Appendix_J_-_Installation_HAZMAT_Management_Plan.pdf

Thule Air Base Installation HAZMAT Management Plan

Installation HAZMAT Management Plan (IHMP)

Thule Air Base, Greenland

OPR: GREENLAND CONTRACTORS

Chief of Environmental Engineering DSN 629-3840 ext. 2698 Supersedes IHMP Oct 2011

14 March 2014

TABLE OF CONTENTS

1 LETTER OF INSTRUCTION

1.1 SECURITY AND ADMINISTRATIVE INSTRUCTIONS

2 GENERAL

2.1 INTRODUCTION

2.2 PURPOSE

2.3 SCOPE

2.4 REGULATORY OVERVIEW

3 ORGANIZATION AND RESPONSIBILITIES

3.1 HMMP TEAM

3.2 IHMP OBJECTIVES

4 HAZARDOUS MATERIAL CHARACTERISTICS

4.1 DEFINITIONS OF HAZARDOUS MATERIALS (HAZMAT)

4.2 HAZMAT PRODUCTS LISTED FOR SUBSTITUTION IF POSSIBLE

4.3 PRODUCTS NOT CONSIDERED AS HAZMAT

4.4 HAZMAT AUTHORIZATION PROCESS

5 LABELING OF HAZMAT PRODUCTS

6 HAZMAT STORAGE AREAS

6.1 SHOP INVENTORY AND MATERIAL SAFETY DATA SHEETS (MSDS)

6.2 GENERAL HOUSEKEEPING OF HAZMAT STORAGE AREAS

6.3 INSPECTIONS OF HAZMAT STORAGE AREAS

7 ACRONYMS

8 APPENDICES

1 LETTER OF INSTRUCTION

1.1 Security and Administrative Instructions

Title: The title of this document is “Installation HAZMAT Management Plan”. The acronym, IHMP, will be used throughout the document.

Classification: The title and the document are unclassified, and do not fall within the scope of directives governing the protection of information affecting National Security as specified in the United States Air Force (USAF) directives, in the Air Force Instruction (AFI) 31-series.

Responsibilities: Greenland Contractors, Environmental Engineering (GC/EE) is the office of primary responsibility for developing and maintaining the IHMP. Organizations are authorized to extract and reproduce those sections of the IHMP that are essential in the accomplishment of necessary planning and in the preparation of supporting document and reports.

References: References referred to in the IHMP do not appear in the plan, but they may be accessed through GC Environmental Engineering or the Air Force Electronic Publication Library

(AFEPL).

Reviews/Changes: The IHMP will be reviewed and updated annually. Furthermore, the plan is subject to change if any of the applicable laws, regulations, or requirements is altered.

Initial Distribution: Mr. Donald Chase, USAF, 21 CES/CEIE, Environmental COR Mr. Joseph Partoll, USAF, 21 AMDS/SGPB, Bioenvironmental COR Capt Nathan Thomsen, USAF, 821 SPTS Civil Engineer Flight CC/COR

Final Distribution:

Mr. Donald Chase, USAF, 21 CES/CEIE, Environmental COR Mr. Joseph Partoll, USAF, 21 AMDS/SGPB, Bioenvironmental COR Capt Nathan Thomsen, USAF, 821 SPTS Civil Engineer Flight CC/COR TSgt Jeffery Desjardins, USAF, 821 SPTS Logistics Flight, Supply COR Capt Jason Stack, USAF, 821 SFS/CC Ms. Susan Iversen, BAE Systems Mr. Michael Krueger, Harris Mr. Arthur French, Honeywell Mr. Joe Hurley, National Science Foundation Mr. Jens Ole Nielsen, Air Greenland Mr. Finn Bo Madsen, DTU Space (Technical University of Denmark) Mr. Patrick King, US Embassy (contracting), Copenhagen Greenland Contractors (all sections via GC Intranet)

2 GENERAL

2.1 Introduction

The purpose of the Installation HAZMAT Management Plan (IHMP) is to provide the Air Force installation with a standardized way to handle HAZMAT from cradle to grave. Although the focus is on HAZMAT, the broader purpose is to protect the environment, safety and health of potentially all Thule residents.

According to AFI32-7086 the Installation Hazardous material management process (HMMP) team functions to provide an oversight for three major areas which are the IHMP, the Weapon system HAZMAT Program (WSHP) and the ODS Program.

This program assigns specific functional area responsibilities for HMMP execution at all levels.

The key to effective HMMP management is cross-functional cooperation to be achieved through the establishment of HMMP teams at all levels.

At Thule AB the HMMP is facilitated by BMC. The ODS Program is set out in CDRL CEV-20 and the IHMP describes the HAZMAT Pharmacy requirements for authorizing, procuring, issuing, and monitoring HAZMAT which is described in this plan. The only identified HAZMART is part of the BMC.

The BMC does not manage the WSHP and shipping of explosives is not covered by this plan.

Questions regarding the WSHP should be directed to 821 SFS and 821 SPTS/CE.

2.2 Purpose

In accordance with the U.S. Air Force Instruction (AFI) 32-7086, Hazardous Materials Management; this document represents the Installation HAZMAT Management plan (IHMP) for Thule AB, Greenland.

The purpose of the IHMP is to ensure that documented guidance for Hazardous material (HAZMAT) management is available to all installation personnel.

The documentation will include:

• Identification of Shops using HAZMAT

• Identification of HAZMAT storage

• HAZMAT tracking at Thule AB

• Procedures for HAZMAT procurement and authorization

• An overview of HAZMAT storage locations and inspection intervals

The goal is to achieve a full state of awareness throughout the installation of hazardous material (HAZMAT). The IHMP ensures the purchase of only the smallest quantities of hazardous materials necessary by focusing on eliminating or, reducing the introduction of hazardous material into the installation.

Throughout this document the abbreviation BMC is used for Base Maintenance Contract the point of contact for the BMC is GC Environmental Engineering (email: Environmental@gc.gl).

2.3 Scope

The provisions of the IHMP apply throughout Thule AB and to all personnel. Certain responsibilities are specifically assigned to selected individuals identified in the plan.

Related plans that are developed to cover functions may need to be consulted:

• Polychlorinated Biphenyl (PCB) Replacement Plan, CDRL CEV-12

• Hazardous Waste Management Plan, CDRL CEV-15B

• Spill Prevention and Response Plan, CDRL CEV-15C

• Pollution Prevention Management Plan, CDRL CEV-15D

• Halon and Refrigerant Management Plans, CDRL CEV-20

2.4 Regulatory Overview

In accordance with USAF policy, Thule AB is required to comply with the following regulations.

Thule Air Base: Final Governing Standard (FGS)

Environmental, Safety, Occupational Health Council (ESOHC) decisions

USAF: AFI32-7086 November 2004

3 ORGANIZATION AND RESPONSIBILITIES

In order to ensure that HAZMAT is handled in a correct manner, it is important that the personnel using HAZMAT are fully aware of their responsibilities in the HAZMAT management program

(HMMP).

3.1 HMMP Team

AFI32-7086 Section 1.4.2 provides guidance on HMMP team composition. These functions are all either contracted to the BMC (Environmental, Fire Protection, Civil Engineering, Bioenvironmental Engineering, Civil Engineering, HAZMART, Maintenance etc.) or not represented on-base (contracting, legal). As a consequence, dedicated HMMP meetings are not feasible. The HMMP is implemented through weekly meetings between 821 SPTS/CE, GC/EE and the BCE. Major issues will be presented at the ESOH Council were appropriate CORs are represented and additional functions can be engaged (Finance, tenant units, Manpower etc).

3.2 IHMP Objectives

The IHMP supports accomplishment of the Air Force mission by minimizing and effectively managing dependence on HAZMAT within acceptable levels of mission and EESOH risk and reducing associated HAZMAT life cycle costs.

The specific objectives of the IHMP are to:

1. Purchase, store and issue HAZMAT in smallest quantities required to support accomplishment of the Air Force mission

2. Focus to improve process efficiency

3. Provide standardized HAZMAT service to costumer

4. Ensure HAZMAT issue and use conform to appropriate EESOH requirements

5. Track HAZMAT by shop, facility and where applicable

6. Enter all required HAZMAT data into EESOH-MIS, the resent established HAZMAT tracking program at Thule AB

7. Provide HAZMAT data to support Air Force requirements

4 HAZARDOUS MATERIAL CHARACTERISTICS

A material is considered to be a hazardous material if it exhibits either a health hazard and/or a physical hazard.

4.1 Definitions of Hazardous Materials (HAZMAT)

A commonly accepted definition (OSHA 29CFR 1910.1200) of hazardous materials includes products which are carcinogens, toxic or highly toxic agents, reproductive toxins, irritants, corrosives, sensitizers, hepatotoxins, nephrotoxins, neurotoxins, agents which act on the hematopoietic system, and agents which damage the lungs, skin, eyes, or mucous membranes.

Physical hazard means a product for which there is scientifically valid evidence that it is a combustible liquid, a compressed gas, explosive, flammable, an organic peroxide, an oxidizer, pyrophoric, unstable (reactive) or water-reactive.

Typical hazardous materials characteristics as they are defined in the Final Governing Standard (FGS) Table C5.T1:

1. The item is a health or physical hazard. Health hazards include carcinogens, corrosive materials, irritants, sensitizers, toxic materials, and materials which damage the skin, eyes, or internal organs. Physical hazards include combustible liquids, compressed gasses, explosives, flammable materials, organic peroxides, oxidizers, pyrophric materials, unstable (reactive) materials, and water-reactive materials.

2. The item/or its disposal is regulated by the host nation because of its hazardous nature.

3. The item contains asbestos, mercury, or polychlorinated biphenyls.

4. The Item has a flashpoint below 93˚C (200˚F) closed cup, or is subject to spontaneous heating or is subject to polymerization with release of large amounts of energy when handled, stored, and shipped without adequate control.

5. The item is a flammable solid or is an oxidizer or is a strong oxidizing or reducing agent with a standard reduction potential of greater than 1.0 volt or less than -1.0 volt.

6. In the course of normal operations, accidents, leaks, or spills, the item may produce dusts, gases, fumes, vapors, mists, or smokes with one or more of the above characteristics.

7. The item has special characteristics, which in the opinion of the manufacturer or the DoD

Components could cause harm to personnel if used or stored improperly.

4.2 HAZMAT Products listed for substitution if possible

EPA has listed 31 substances as priority chemicals in the National Waste Minimization Program.

This program is used for guidance by GC/EE when reviewing HAZMAT requests and considering candidates for substitution to products with a lesser environmental impact at Thule AB. The 31 chemicals are listed below

Table 1: List of EPA-Priority Chemicals:

1. 1,2,4-Trichlorobenzene 17. Hexachloroethane

2. 1,2,4,5-Tetrachlorobenzene 18. Methoxychlor

3. 2,4,5-Trichlorophenol 19. Naphthalene

4. 4-Bromophenyl phenyl ether 20. Pendimethalin

5. Acenaphthene 21. Pentachlorobenzene

6. Acenaphthylene 22. Pentachloronitrobenzene

7. Anthracene 23. Pentachlorophenol

8. Benzo(g,h,i)perylene 24. Phenanthrene

9. Dibenzofuran 25. Polycyclic Aromatic Hydrocarbons

10. Dioxins and Furans 26. Polychlorinated biphenyls

11. Endosulfan, alpha & Endosulfan, beta 27. Pyrene

12. Fluorene 28. Trifluralin

13. Heptachlor & Heptachlor Epoxide 29. Cadmium

14. Hexachlorobenzene 30. Lead

15. Hexachlorobutadiene 31. Mercury

16. Hexachlorocyclohexane

Besides the 31 chemicals the HAZMAT regulations from the Danish OSHA are also used as guidelines.

Furthermore, the Final Governing Standard (FGS) prohibits all procurement of products containing polychlorinated biphenyls (PBCs).

4.3 Products not considered as HAZMAT

Commonly accepted criteria (OSHA 29CFR1910.1200(b)(6)) for products not considered being HAZMAT is as follows below. These considerations are consistent with the Final Governing Standards (FGS) intent and will be considered valid for Thule AB.

1. Any hazardous waste as such term is defined by the Solid Waste Disposal Act. The specific handling this at Thule AB is outlined in CDRL CEV-15B.

2. Any hazardous substance as such term is defined by the Comprehensive Environmental Response.

3. Tobacco or tobacco products

4. Wood or wood products

5. Articles hereby meant as:

Manufactured item other than a fluid or particle:

- Which is formed to a specific shape or design during manufacture.

- Which has end use function(s) dependent in whole or in part upon its shape or design during end use.

- Which under normal conditions of use does not release more than very small quantities, e.g., minute or trace amounts of a hazardous chemical, and does not pose a physical hazard or health risk to employees.

6. Food or alcoholic beverages which are sold, used or prepared in a retail establishment and foods intended for personal consumption by employees while in the workplace.

7. Any drug, as that term is defined in the Federal Food, Drug and Cosmetic Act.

8. Cosmetics which are packed for sale in a retail establishment, and cosmetics intended for personal consumption by employees while in the workplace.

9. Any consumer product or hazardous substance, as those terms are defined in the Consumer Product Safety Act and Federal Hazardous Substances Act respectively.

10. Nuisance particles where the chemical manufacturer or importer can establish that they do not pose any physical or health hazard.

11. Ionizing and non-ionizing radiation

12. Biological hazards

A List of typical products which are not hazardous according to the criteria above has been prepared as a guideline for users. Products on this list will not be tracked nor does their use require authorization, this list is added as Appendix 1.

4.4 HAZMAT Authorization Process

Hazmat requests are handled IAW procedures described in this section.

A product needed for a task is shipped to TAB.

1. User requests a product

2. MSDS and AF Form 3952 is sent to GC/EE

3. GC/EE review the documents and submit a request for the EESOH-MIS data stewards

4. MSDS is approved by EESOH-MIS data stewards

5. GC/EE register MSN-number of product to the user in EESOH-MIS

6. The product is now approved for use on TAB

NOTE: A product must be approved according to the above before it can enter TAB.

Any non-BMC HAZMAT requests are reviewed for informational purposes only. GC/EE may provide guidelines and recommendations for substitutions and will track the material in EESOH-

MIS.

It is the responsibility of the requester to provide a Material Safety Data Sheet (MSDS) in English, prepared by the manufacturer that fulfils CFR and/or EU requirements when a new product is requested.

Furthermore, amounts of procured HAZMAT in pounds (lbs) must be reported to the BMC

(GC/EE).

The process is shown in figure 1.

The documents, MSDS and AF Form 3952 request, can be sent by email to:

Environmental@gc.gl

A form (EESOH-MIS MSDS Request Form) indicating the information needed to receive a material stock number (MSN number) for EESOH- MIS can be used as an alternative to AF Form 3952 and is attached as Appendix 2.

AF Form 3952 is added as Appendix 3. The instruction on how to fill out the AF Form 3952 can be found in AFI32-7086.

Figure 1 Flowchart showing the HAZMAT authorization procedure mailto:Environmental@gc.gl�

5 LABELING OF HAZMAT PRODUCTS

All HAZMAT products shall contain a label. The chemical manufacturer or distributor shall ensure that all hazardous products leaving the workplace are labeled, tagged or marked with:

1. Identity of the hazardous product

2. Appropriate hazard warnings

3. Name and address of the chemical manufacturer, importer or other responsible party

In case a products label has become damaged, obscured, illegible or otherwise does not convey the information required or if a product is contained in a non-original container a label will have to be made.

Presently DD Form 2522 is commonly used at Thule AB when a new label is needed. This is filled out as follows:

1. The Name of the product

2. Hazard code if available

3. The MSN-number of the product

4. The individual part number of the product if this is at hand

5. Item name

6. The Hazardous Materials Identification System

(HMIS)

7. Specific hazards can be identified if there is any.

In case the product is labeled with The Global Harmonized System (GHS) the classifications can be added to this box

8. PPE can be marked in this box

9. The manufacturer importer or other responsible party identification

10. Procurement year if available

Figure 2 DD Form 2522, Hazardous Chemical warning Label

The Final Governing Standard requires as mentioned above, identity of the hazardous product, appropriate hazard warnings and name and address of the chemical manufacturer, importer or other responsible party. Therefore when using DD Form 2522 it is important to fill out box number 1 - Product identity, box 3 – MSN-number, box 6 or 7 - appropriate hazard warnings, when knowing HMIS warnings fill out box 6 and when knowing GHP warnings use box 7, box 8

– it is very important to consider the kind of PPE needed when using the product hence it is important to relate to box 8 and box 9 a – company name.

6 HAZMAT STORAGE AREAS

IAW the Final Governing Standard, C5.3 materials must be stored in a safe and secure area to limit access and prevent inadvertent release.

6.1 Shop Inventory and Material Safety Data sheets (MSDS)

All shops must keep an inventory list of the HAZMAT contained in the shop and keep a file containing Material Safety Data sheets (MSDS) of all their products. The inventory lists must be updated annually or when a new product is added to the shop. These shop inventories shall match the inventory entered to the EESOH-MIS by the BMC GC/EE. Appendix 4 is an example of an inventory list.

As part of the IHMP the BMC GC/EE will update an Installation listing of all HAZMAT storage locations for shops and HAZMART Pharmacy. This list is added as Appendix 5.

6.2 General Housekeeping of HAZMAT Storage Areas

All HAZMAT dispensing areas will be properly maintained. Drums/containers must not be leaking. Drip pans will be placed under containers as necessary to collect drips or spills.

Container contents will be clearly marked and dispensing areas will be located away from catch basins and storm drains.

6.3 Inspections of HAZMAT Storage Areas

All HAZMAT storage areas will be subject to recurring inspections. The frequency of inspections is based on type and amounts of stored materials, as well as the result of previous inspections.

An annual inspection plan is created before each fiscal year. Facility managers or alternates will be notified and can participate in the inspection. In Appendix 6 a list of HAZMAT locations and their inspection intervals is given. This list is used to plan the annual HAZMAT inspections.

7 ACRONYMS

AB Air Base AF Air Force AFI Air Force Instruction BMC Base Maintenance Contract DRMO Defense Reutilization and Marketing office EESOH-MIS Enterprise Environmental, Safety & Occupational Health –

Material Inventory System ESOH Environmental, Safety & Occupational Health EPA U.S. Environmental Protection Agency FGS Final Governing Standard ESOHC Environmental, Safety, Occupational Health Council GC Greenland Contractors GC/EE Greenland Contractors Environmental Engineering HAZMART Hazardous Materials Pharmacy HAZMAT Hazardous Material HMMP Hazardous Material Management process IHMP Installation HAZMAT Management Plan MSDS Material Safety Data Sheet MSN Material Stock Number ODS Ozone Depleting Substances ODSP Ozone Depleting Substances Program POC Point of Contact

8 APPENDICES

APPENDIX 1: EXEMPTION LIST

In order to facilitate the use of common products without unnecessary bureaucracy Thule AB has an exemption list from the requirements set forth in the Hazardous Material Management Process. Products on the list can be used safely without training.

HAZMAT EXEMPTION LIST

The following products are exempted from being tracked in EESOH-MIS and being listed on inventory lists and in MSDS binders. Proper disposal requirements are not exempted.

Office supplies including

• Screen cleaners

• Correction ink

• Shredder oil

• Printer ink cartridges

• Glue sticks

• Markers and Pens

• Antistatic agents

Ordinary soap including

• Hand soap, including liquid soaps and shampoo.

• Ordinary dishwashing detergent (i.e. not detergent for industrial machine washing)

• Cleaning agents (non-industrial)

Miscellaneous products including

• Batteries (for flashlights, watches, hand tools and other equipment etc.)

• Bug Repellants

• Perfume, including air fresheners

• Hand sanitizers

• Disinfection swipes (paper towels with disinfection agent)

APPENDIX 2: INFORMATION NEEDED TO RECEIVE A MATERIAL STOCK NUMBER, MSN

NUMBER, FOR EESOH-MIS

APPENDIX 3: AF FORM 3952 IS ADDED AS AN EXAMPLE

This AF form can be found at http://www.e-publishing.af.mil/shared/media/epubs/AF3952.xfdl, the instruction on how to fill out this form is given in AFI32-7086.

http://www.e-publishing.af.mil/shared/media/epubs/AF3952.xfdl�

APPENDIX 4: HAZMAT INVENTORY LIST (EXAMPLE)

APPENDIX 5: INSTALLATION LISTING OF ALL HAZMAT STORAGE LOCATIONS FOR

SHOPS AND HAZMART PHARMACY

EESOH-MIS SHOP NAME RESPONSIBLE

ORGANISATION

EESOH-MIS

SHOP CODE

HAZMAT STORAGE

BUILDING

HAZMART Pharmacy GC Supply

GC/EE HAZ99 #935, #933, #555, HG2

GC, QES Laboratory GC/EE TH0501 555 GC, Medical Clinic GC/EE TH0601 #118 Dentist GC/EE TH0602 #118 GC Operations, Transportation, Ramp Services

GC/EE TH0901 HG4, HG7, HG8, HG9

GC Operations, Transportation, Pavement and Grounds

GC/EE TH0902 HG3, HG9, #580

GC Operations, Transportation, Transportation Services

GC/EE TH0903 HG3

GC Operations, Transportation, AGE

GC/EE TH0904 #1408

GC Operations, Enterprise, Painting

GC/EE TH1101 #801

GC Operations, Enterprise, Fixed Price Projects

GC/EE TH1102 #571, #801

GC Operations, UFM, Heating

GC/EE TH1201 #1401,#935, #341, #241

GC Operations, UFM, Power

GC/EE TH1203 #1391, #4016

GC Operations, UFM, Bowling Pinsetter

GC/EE TH1204 #608

GC Operations, UFM, Fuels

GC/EE TH1205 #1307, #616, #614, HG3

GC Operations, UFM, Polynea

GC/EE TH1206 #992

GC Operations, UFM, Flightline

GC/EE TH1207 #1105

GC Operations, UFM, UFM

GC/EE TH1208 #551, #200

GC Operations, UFM, BMEWS

GC/EE TH1209 #4002

GC Operations, UFM, DET-1

GC/EE TH1210 #1825

GC Operations, UFM, Water Treatment

GC/EE TH1211 #1400, #1411, #608

GC Operations, UFM, Refrigiration

GC/EE TH1212 #551

GC Operations, Fire Mainbase

GC/EE TH1301 #628, #619

GC Operations, Fire BMEWS

GC/EE TH1302 #4002

GC Operations, Non Secure Communications

GC/EE TH1401 #1950, #1411

GC Operations, ATCALS

GC/EE TH1402 #1950, #1411

GC Operations, Vehiecle Maintenance, Maintenance

GC/EE TH1601 #580

GC Operations, Vehicle Maintenance, Refuling

GC/EE TH1602 #563

GC Operations, Vehicle Maintenance, Paint Shop

GC/EE TH1603 #580

GC Operations, Vehicle Maintenance, Boat Team

GC/EE TH1604 #580

GC Services, Activities, Fitness

GC/EE TH1901 #608

GC Services, Activities, Community Center

GC/EE TH1902 #362

GC Services, Housing

GC/EE TH2101 #608, #237, #107

Basewide depots

GC Services, Food Services

GC/EE TH2201 #4002, #1824, #107

GC Services, Supply

GC/EE TH2401 #935

GC Administration GC/EE TH3021 #274, #564, #619 BAE-Systems, PMEL

Thule BAE

TH9001 #561

BAE-Systems, BMEWS

TH9002 #4002

BAE-Systems, LAN

TH9003 #112

Air Greenland Air Greenland TH9004 HG4 Harris Harris TH9005 #1824

821 SFS 821 SFS TH9006 #363

NRG NRG TH9007 #1391

Canadian Air Force Canadian Air Force TH9008 HG7

AAFES,

AAFES TH9009 #1409, #251

12 SWS 12 SWS TH9010 #4002

AAFES,

TOW-Club

AAFES TH9011 #236

NSF NSF TH9012 #2403, HG4, Camp Tuto Base Camp

Private Organisations Gocart Club, Skeet Club, RC car Club

TH9014

- Go-cart Club by the SAC- Ramp

- Skeet Club by the beach

- RC car Club by abandoned Runway near HG2

MT Hojgaard MTH TH9015 #974 GC Boat Guild GC/EE TH9016 Installation TAB GE Americom J-Site GE Americom TH9017 #4002 AARSLEFF AARSLEFF TH9018 Various locations

BAE ARHE PROJECTS BAE TH9019 Container at Tank Farm Brøndum Brøndum TH9020 Container at the pier Pilegaard & Henriksen Pilegaard & Henriksen TH9021 Various locations ARSSARNERIT A/S ARSSARNERIT A/S TH9022 Various locations Adserballe & Knudsen Adserballe & Knudsen TH9023 #211, various locations Raytheon Raytheon TH9024 Various locations DTU Space DTU Space TH9025 #898

APPENDIX 6: HAZMAT LOCATIONS AND THEIR INSPECTION INTERVALS

HAZMAT Inspections at TAB

Frequency > annually Annual inspection Frequency < annually #555 (Lab/HAZMART) #107 (Dining Hall) #112 (BAE) #580 (VM/P&G) #237 (Housing) #118 (Medical Clinic/Dentist) #604 (HAZMART) #241 (E-Plant) #200 (UFM) #605 (HG3) (Transportation) #251/#1409 (BASE EXCHANGE) #236 (TOW Club) #623 (HG7 – BOXTOP) #341 (D-Plant) #363 (SFS) #629 (HG9) #362 + Container (CC) #561 (PMEL)

#630 (HG10) #551 (UFM) #570 (HAZMART)

#935/937 (HAZMART) #563 (VM) #610 (HG6)

#1091 (HG2) #606 (HG4/Air Greenland) #622 (FIRE) #1391 (M-Plant) #608 (Fitness/UFM/Housing) #933 (Supply) #1401 (K-Plant) #623/624 (HG7/HG8) (RAMP services) #992 (UFM)

#2403 (NSF) #628 (FIRE) #1105 (UFM)

#4002 (BMEWS/SMART-1) #801 (Enterprise/P&G) #1307 (UFM) #4016 (J-Plant) #836 (Cold storage) #1409 (AAFES)

#935 (UFM) #1950 (NSC)

#972 (Cold Storage) #1951 (NSC) #974 (MT Højgaard) #4002 (BAE/USAF)

#1090 (HG1) #4002 (FIRE)

#1400/1411 (Water Treatment) #RC Club by HG2 #1408 (AGE) #SAC-RAMP (Go-Cart Club)

#1411 (NSC) CARS

#1824 (SMART-1/HARRIS/Honeywell) #4002 (Food Services) DRMO Yard