EXHIBIT_P_-_ELECTRICAL_AND_COMMUNICATIONS.pdf

EXHIBIT P - ELECTRICAL AND COMMUNICATIONS

G

F

E

D

C

B

A

2 3

#6 BARE COPPER

CONDUCTOR

ISOMETRIC ELEVATION

STATIONARY INFANTRY TARGET

NOTTO SCALE

NOTES:

1. RE-USE EXISTING CABLES CONDUITS WITH POWER AND

DATA CABLES ENTERING EMPLACEMENT.

2. INSTALL NEW CONDUIT HUB WITH CABLE SEAL FITTING IN

NEW MTDP. SEE DETAIL ON E-07.

3. PROTECT POWER AND DATA CABLES DURING

REMOVAUDEMOLITION OF EXISTING DATA ENCLOSURE

LOADCENTER. RE-TERMINATE DATA CABLES IN NEW

MTDP ENCLOSURE AND POWER CABLES IN NEW

LOADCENTER.

4. EQUIPMENT SHALL NOT BE MOUNTED HIGHER THAN 2"

FROM TOP OF EMPLACEMENT WALL.

5. POWER TO DATA PANEL RECEPTACLE IN MTDP SHALL BE

ROUTED THROUGH SINGLE POLE SINGLE THROW SWITCH.

6. OUTLET BOXES SHALL BE MOUNTED SO THAT CONDUIT

RUNNING FROM OUTLETS TO LOADCENTER AND MTDP

ENCLOSURES ARE PERPENDICULAR. BENDS AND

CONDUIT OFFSETS TO ENTER ENCLOSURES ARE

UNACCPETBLE.

7. TPR, APR AND DPR SHALL NOT BE GFCI PROTECTED.

8. PERMANENTLY LABEL THE EMPLACEMENT ACCORDING TO

EXISTING LABELING SCHEME. COORDINATE LABELING

WITH FT HOOD RANGE OPERATIONS.

9. PROVIDE SEAL FITTINGS AS SHOWN IN DETAILS ON SHEET

E-07 FOR ALL CABLE ENTRANCES INTO NEMA 4 RATED

ENCLOSURES.

PANEL BOARD: SIT LOCATI ON: XXXX

125 AM P MAIN MAIN LUGS ONLY

VOLTAG E: 240/120 PHASE: 1 WIRE: 3

VAi PHASE

LOAD SERVED

NO. TRIP WIRE

A B

CKT

POLES AM PS SIZE NO.

SURGE ARRESTOR 2 ---- --- 1

SUB FEED THRU LUGS 2 ---- --- 5

0 0

TOTAL VA PHASE A: 444

TOTAL VA PHASE B: 394

SUPPLIED FROM: TRSF-XX

10. INSTALL MYERS TYPE HUBS ON ALL CONDUIT

PENETRATIONS TO SIDE OF ENCLOSURE.

11. ALL DIMENSIONS SHOWN IN INCHES UNLESS OTHERWISE

NOTED.

12. PROVIDE TARGET AND AUXILIARY OUTLETS WITH NEMA 3R

WET LOCATION COVERS MAKING OUTLETS SUITABLE FOR

USE IN WET LOCATIONS. SEE DETAIL SHEET E-07 FOR WET

LOCATION COVER. IN USE COVERS WITH COVERS

INTENDED TO CLOSE OVER THE INSERTED CORD ARE NOT

ACCEPTABLE AS THESE COVERS WILL NOT CLOSE OVER

TARGET OR AUXILIARY CORDS.

13. DEVIATIONS TO THE EQUIPMENT SIZES, EQUIPMENT

NUMBERS, RECEPTACLE COVERS, OR CABLE ENTRY

METHODS INTO ENCLOSURES WILL REQUIRE RANGE

TRAINING AND LAND PROGRAM HUNTSVILLE CENTER

MANDATORY CENTER OF EXPERTISE APPROVAL.

14. SEE SHEET E-08 FOR ADDITIONAL INFORMATION ON

MASTER TARGET DATA PANELS.

MOUNTED: SURFACE FEED: BOTTOM

ASYM A. I. C MIN. : 10,000

RATING: NEMA 3R

VAi PHASE

CKT

A B

WIRE TRIP NO.

LOAD SERVED NO. SIZE AM PS POLES

394 SIT (NEMA L 14-20R &

2 12 20 2 NEMA L5-20R) 394

6 50 12 20 1 TDP AND MR

8 --- --- 20 1 SPARE

444 394

TOTAL CONNECTED WATTAGE: 838

TOTAL DEMAND AM PS: 3

5 6

LATCHED TYPE REMOVABLE LID.

CONTINUOUS HINGE WITH

REMOVABLE PIN. NEMA 4

ENCLOSURE. SEE NOTE 14.

CONDUIT WITH FIBER OPTIC

DATA CABLES. SEE

NOTE 1-3, & 9.

#6 AWG BARE COPPER

CONDUCTOR. SEE NOTE 9.

CABLE SEAL FITTING.

SEE NOTE 9. TYPICAL

SINGLE GANG 2 5/8" DEEP WEATHERPROOF

BOX WITH WEATHERPROOF BLANK COVER

FOR USE BY TARGET VENDOR.

8 9 10

GFCI MAINTENANCE RECEPTACLE (MR)

AND SINGLE POLE, SINGLE THROW 120V

SWITCH IN WEATHERPROOF ENCLOSURE

WITH COVER. SEE NOTE 4 & 5.

TARGET POWER RECEPTACLE (TPR)

120/240V, 20A, 4 WIRE. TWIST LOCK

(NEMA L 14-20R) WITH WEATHERPROOF

ENCLOSURE WITH WET LOCATION

COVERS. SEE NOTES 4, 7, & 12.

SEE NOTE 8

POWER CABLE IN CONDUIT TO

NEXT/PREVIOUS TARGET PIT.

SEE NOTES 1-3.

AUXILIARY POWER RECEPTACLE (APR) 120V, 20A,

3 WIRE, TWIST LOCK (NEMA L5-20R) WITH WET

LOCATION COVER IN WEATHERPROOF

ENCLOSURE. SEE NOTE 7 & 12.

FRONT ELEVATION

STATIONARY INFANTRY TARGET

DATA POWER RECEPTACLE (DPR) LOCATED

INSIDE PANEL. SEE NOTES 14. RECEPTACLE

SHOWN ON MTDP DETAIL.

NOTTO SCALE

TOP ELEVATION

STATIONARY INFANTRY TARGET

NOTTO SCALE

WALL MOUNTED NEMA 3R

LOADCENTER

13"H X 12"W X 6"D MAX

#6 AWG BARE COPPER

CONDUCTOR, 6' COILED

ABOVE GROUND FOR

BONDING TO FUTURE

TARGET

US Army Corps of Engineers® u 0:

a.

f-:,; :,;

<( e. w

0: CD

(9 ~ ~

Cf) Ct'.

Ou, z <{

8:~~ _J f-

~ >-OU(.') Ct'.

'.'izffi ~ w f-a, ;;: 0 z (.')a,<( _J <{ ~5g: <{ lJ._

~U w (.) ~ <ocn ir >-~g~ f- Ct'.

0 :,:0: (.) <{

~~~ w z _J 0 UJQ>- w

(.') u_J f'= z :, 0: -;j_ Cf) ci i5

SHEET ID

E-01

F

E

D

C

B

A

WALL MOUNTED NEMA 3R

LOADCENTER. SEE NOTE 4

POWER CABLE FROM 120/240V

POWER SOURCE IN CONDUIT.

SEE NOTES 1-3

POWER CABLE TO NEXT TARGET

EMPLACEMENT IN CONDUIT.

SEE NOTES 1-3.

2 3 4 5 6 7

SAT TAR GET ELEVATION

EQUIPMENT MOUNTED ON 1.625" DEEP

UNISTRUT. SEE NOTE 6.

NOTTO SCALE

TARGET POWER RECEPTACLE (TPR) 120/240V, 20A,

4 WIRE, TWIST LOCK (NEMA L 14-20R) WITH WET

LOCATION COVER IN WEATHERPROOF ENCLOSURE

SEE NOTES 4, 8, & 13.

GFCI MAINTENANCE RECEPTACLE (MR)

AND SINGLE POLE, SINGLE THROW, 120V

SWITCH IN WEATHERPROOF ENCLOSURE

WITH COVER. SEE NOTES 4 & 5.

RIGID METAL CONDUIT.

TYPICAL.

SINGLE GANG 2 5/8" DEEP WEATHERPROOF

BOX WITH WEATHERPROOF BLANK COVER

FOR USE BY TARGET VENDOR.

AUXILIARY POWER RECEPTACLE (APR), 120V, 20A,

3 WIRE, TWIST LOCK (NEMA L5-20R) IN

WEATHERPROOF ENCLOSURE WITH COVER. SEE

NOTES 4, 8, & 13.

CABLE SEAL FITTING

SEE NOTE 10

#6 AWG BARE COPPER

CONDUCTOR

#6 BARE COPPER CONDUCTOR

SEE NOTE 10

#6 AWG BARE COPPER CONDUCTOR, 10' COILED

ABOVE GROUND FOR BONDING TO FUTURE TARGET.

SEE NOTE 7.

LATCHED TYPE REMOVABLE LID.

CONTINUOUS HINGE WITH

RE MOVEABLE PIN. NEMA 4 TYPE

ENCLOSURE. SEE NOTES 4.

CONDUIT/CABLE SEAL FITTING.

SEE NOTE 18

EXISTING FIBER OPTIC CABLE

ENCLOSURE. SEE NOTE 19.

PANEL BOARD: SAT

XXXX MAIN

VOLTAGE: 240/120

LOAD SERVED

NO.

POLES

SURGE ARRESTOR 2

SPARE 1

SPACE

SPACE

SPACE

TOTAL VA PHASE A: 1375

TOTAL VA PHASE B: 1325

SAT TARGET ENLARGED ELECTRICAL EQUIPMENT ELEVATION SUPPLIED FROM: TRSF-XX

NOTTO SCALE

TRIP

AMPS

8 9 10

NOTES:

1. RE-USE EXISTING CABLES CONDUITS WITH POWER AND

DATA CABLES ENTERING EMPLACEMENT.

2. INSTALL NEW CONDUIT HUB WITH CABLE SEAL FITTING IN

NEW MTDP. SEE DETAIL ON E-07.

3. PROTECT POWER AND DATA CABLES DURING

REMOVAL/DEMOLITION OF EXISTING DATA ENCLOSURE

LOADCENTER. RE-TERMINATE DATA CABLES IN NEW

MTDP ENCLOSURE AND POWER CABLES IN NEW

LOADCENTER.

4. EQUIPMENT SHALL NOT BE MOUNTED HIGHER THAN 2"

FROM TOP OF EMPLACEMENT WALL.

5. POWER TO DATA PANEL RECEPTACLE IN MTDP SHALL BE

ROUTED THROUGH SINGLE POLE, SINGLE THROW SWITCH.

6. ALL EQUIPMENT SHALL BE MOUNTED ON 1.625" DEEP

UNISTRUT. NO EQUIPMENT SHALL BE PERMITTED TO BE

INSTALLED DIRECTLY TO CONCRETE WALL.

7. FOR FLANK TYPE SAT TARGET INCREASE THE LENGTH OF

GROUND CABLE TO 18 FT.

8. TPR, APR AND DPR SHALL NOT BE GFCI PROTECTED.

9. PERMANENTLY LABEL THE EMPLACEMENT ACCORDING TO

THE CIVIL AND ELECTRICAL DESIGNATIONS.

10. PROVIDE SEAL FITTINGS AS SHOWN IN DETAIL ON SHEET

E-07 FOR ALL CABLE PENETRATIONS TO NEMA 4, 4X, OR 6P

RATED ENCLOSURES.

11 . INSTALL MYERS TYPE HUBS ON ALL CONDUIT

PENETRATIONS TO SIDE OF ENCLOSURE.

12. ALL DIMENSIONS SHOWN IN INCHES UNLESS OTHERWISE

NOTED.

13. PROVIDE TARGET AND AUXILIARY OUTLETS WITH NEMA

3R WET LOCATION COVERS MAKING OUTLETS SUITABLE

FOR USE IN WET LOCATIONS. SEE DETAIL SHEET E-07

FOR WET LOCATION COVER. IN USE COVERS WITH

COVERS INTENDED TO CLOSE OVER THE INSERTED CORD

ARE NOT ACCEPTABLE AS THESE COVERS WILL NOT

CLOSE OVER THE TARGET POWER OR AUXILIARY CORDS.

14. DEVIATIONS TO THE EQUIPMENT SIZES, EQUIPMENT

NUMBERS, RECEPTACLE COVERS, OR CABLE ENTRY

METHODS INTO ENCLOSURES WILL REQUIRE RANGE

TRAINING AND LAND PROGRAM HUNTSVILLE CENTER

MANDATORY CENTER OF EXPERTISE APPROVAL.

15. NOT USED.

16. SEE SHEET E-09 FOR ADDITIONAL INFORMATION ON

MASTER TARGET DATA PANELS.

17. MOUNT EQUIPMENT AS LOW AS POSSIBLE ON THE FRONT

WALL OF THE EMPLACEMENT. NO ELECTRICAL

EQUIPMENT SHALL BE INSTALLED WITHIN 2" OF THE TOP

OF THE EMPLACEMENT WALL.

18. CONDUIT/CABLE SEAL FITTING CONNECTION TO THE

MTDP. SEE CONDUIT/CABLE SEAL FITTING DETAIL ON

SHEET E-07.

19. EXISTING FIBER OPTIC CABLE ENCLOSURE. RE-USE

EXISTING ENCLOSURE. SEAL ALL OPENINGS WITH NEMA 4

RATED PLUGS. PROVIDE NEW CONDUIT INTO NEW MTDP

FOR TERMINATION OF EXISTING FIBER OPTIC CABLES

INSIDE NEW MTDP.

LOCATI ON: XXXXXXX MOUNTED: SURFACE FEED: BOTTOM

MAIN LUGS ONLY ASYM A.I.C MIN.: xxxxx

PHASE: 1 WIRE: 3 RATI NG: NEMA 3R

VA/ PHASE VA/ PHASE

WIRE

A B

CKT CKT

A B

WIRE TRIP NO.

LOAD SERVED SIZE NO. NO. SIZE AM PS POLES

--- 1325 SAT (NEMA L 14-20R, --- 1 2 12 20 2 2-NEMA L5-20R) --- 1325

--- --- 5 6 50 12 20 1 TDP AND MR

7 8 --- --- 20 1 SPARE

9 10 1 SPACE

11 12 1 SPACE

0 0 1375 1325

TOTAL CONNECTED WATTAGE: 2,700

TOTAL DEMAND AM PS: 11

US Army Corps of Engineers® u 0:

a.

f-<( e. w 0:

(9 ~ ~

Ou, z Cf) et:

8:~~ _J <{

~ f- OU(.') et:

'.'izffi ~ w 0 a, ;;: 0 ::;;

(.')a,<( _J et: ~5g: <{ <{ ~U w (.)

>-<ocn ir ~g~ f- et:

0 :,:0: (.) z ~~~ w 0 _J

UJQ>- w f'.= (.') u_J

~ z :, <(:,; Cf) 0: -;j_ ci i5

E-02

E

D

C

B

A

2 3

TARGET POWER RECEPTACLE (TPR) 120/240V,

20A, 4 WIRE, TWIST LOCK (NEMA L 14-20R) IN

WEATHERPROOF ENCLOSURE WITH WET

LOCATION COVERS. SEE NOTES 4, 7, & 14.

WALL MOUNTED NEMA 3R LOAD

CENTER. SEE NOTE 4.

RIGID METAL CONDUIT

TYPICAL

EMPLACEMENT WALL

POWER CABLE FROM

120/240V POWER

SOURCE IN CONDUIT.

SEE NOTES 1-3.

2"

MIN

5"

MIN

POWER CABLE IN

CONDUIT TO NEXT

TARGET PIT.

SEE NOTES 1-3.

SEE NOTE 8

4 5

GFCI MAINTENANCE RECEPTACLE (MR)

AND SINGLE POLE, SINGLE THROW, 120V

SWITCH IN WEATHERPROOF ENCLOSURE

WITH COVER. SEE NOTE 5.

EQUIPMENT MOUNTED ON 1.625" DEEP

UNISTRUT. SEE NOTE 6.

2" MIN

SEE NOTE 11 SEE NOTE 9

SINGLE GANG 2 5/8" DEEP WEATHERPROOF

BOX WiTH WEATHERPROOF BLANK COVER

FOR USE BY TARGET VENDOR.

AUXILIARY POWER RECEPTACLE (APR)

120V, 20A, 3 WIRE, TWIST LOCK (NEMA L5-20R)

WITH WET LOCATION COVER IN WEATHERPROOF

#6 AWG BARE ENCLOSUl'tE. SEE NOTES 4, 7, & 14.

COPPER CONDUCTOR ~-----------------~

#6 AWG BARE COPPER CONDUCTOR.

SEE NOTE 18.

#6 AWG BARE COPPER CONDUCTOR

10' COILED ABOVE GROUND FOR

BONDING TO FUTURE TARGET

CONDUIT WITH DATA CABLES

AS SHOWN ON THE RISER DIAGRAM.

SEE NOTES 1-3, 9, & 16.

ELEVATION

6 7

DATA POWER RECEPTACLE (DPR)

LOCATED INSIDE ENCLOSURE.

SEE NOTE 7. RECEPTACLE NOT

SHOWN FOR CLARITY.

78" MAX. SEE NOTE 10.

AREA FOR ELECTRICAL

EQUIPMENT

5"

MIN

LATCHED TYPE REMOVABLE

LID. CONTINUOUS HINGE WITH

REMOVABLE PIN. NEMA 4.

SEE NOTES 4 & 6.

CONDUIT/CABLE SEAL FITTING.

SEE NOTE 13

ELECTRICAL BLOCKOUT TYPICAL OF 2.

SEE CIVIL DETAILS FOR EXACT PLACEMENT.

MOVING INFANTRY TARGET

NOTTO SCALE

NOTES:

1. CONDUIT TO EXTEND 5 FEET BEYOND EMPLACEMENT. 12.

2. CABLES/CONDUITS ARE ROUTED FROM SIDE OF BERM TO

PREVENT CABLE DAMAGE DURING MAINTENANCE OF 13.

PANEL BOARD: MIT LOCATI ON: XXXXXXX MOUNTED: SURFACE FEED: BOTTOM

BERM.

3. ROUTE UNDER SLAB. POWER AND DATA INSTALLED IN

125 MAIN MAIN LUGS ONLY ASYM A.I.C MIN .. 10,000 SAME TRENCH. 14.

VOLTAGE: 2401120 PHASE: 1 WIRE: 3 RATI NG: NEMA3R 4. EQUIPMENT SHALL NOT BE MOUNTED HIGHER THAN 2" VAi PHASE VAi PHASE FROM TOP OF EMPLACEMENT WALL.

LOAD SERVED

NO. TRIP WIRE

A B

CKT CKT

A B

WIRE TRIP NO.

LOAD SERVED POLES AM PS SIZE NO. NO. SIZE AM PS POLES 5. POWER TO DATA PANEL RECEPTACLE IN MTDP SHALL BE

ROUTED THROUGH SINGLE POLE SINGLE THROW SWITCH.

SURGE ARRESTOR

--- 1000 MIT (NEMA L 14-20R &

2 ---- --- 1 2 12 20 2 NEMA L5-20R) --- 1000 6. ALL EQUIPMENT SHALL BE MOUNTED ON 1.625" DEEP 15.

UNISTRUT. NO EQUIPMENT SHALL BE PERMITTED TO BE

SPARE 1 20 --- --- 5 6 50 12 20 1 TDP AND MR INSTALLED DIRECTLY TO CONCRETE WALL.

SPACE 7 8 --- --- 20 1 SPARE

SPACE 9 10 1 SPACE

7. TPR, APR AND DPR SHALL NOT BE GFCI PROTECTED.

SPACE 11 12 1 SPACE

0 0 1050 1000

8. PERMANENTLY LABEL THE EMPLACEMENT ACCORDING TO 16.

THE CIVIL AND ELECTRICAL DESIGNATIONS.

TOTAL VA PHASE A: 1050 9. PROVIDE SEAL FITTINGS AS SHOWN IN DETAIL ON SHEET 17.

TOTAL VA PHASE B: 1000

TOTAL CONNECTED WATTAG E: 2,050

E-07 FOR ALL CABLE PENETRATIONS TO NEMA 4, 4X, OR 6P

RATED ENCLOSURES.

18.

- 10. INSTALL POWER AND DATA ON THE FIRST 78" OF THE

SUPPLIED FROM : TRSF-XX TOTAL DEMAND AM PS: 9

- FRONT WALL CLOSEST TO THE DIRECTION OF FIRE.

11. INSTALL MYERS TYPE HUBS ON ALL CONDUIT

PENETRATIONS INTO THE SIDE OF THE DATA ENCLOSURE.

8 9

ALL DIMENSIONS SHOWN IN INCHES UNLESS OTHERWISE

NOTED.

CONDUIT/CABLE SEAL FITTING CONNECTION TO THE

MTDP. SEE CONDUIT/CABLE SEAL FITTING DETAIL ON

SHEET E-07.

PROVIDE TARGET AND AUXILIARY OUTLETS WITH NEMA

3R WET LOCATION COVERS MAKING OUTLETS SUITABLE

FOR USE IN WET LOCATIONS. SEE DETAIL SHEET E-07

FOR WET LOCATION COVER. IN USE COVERS WITH

COVERS INTENDED TO CLOSE OVER THE INSERTED CORD

ARE NOT ACCEPTABLE AS THESE COVERS WILL NOT

CLOSE OVER THE TARGET POWER OR AUXILIARY CORDS.

DEVIATIONS TO THE EQUIPMENT SIZES, EQUIPMENT

NUMBERS, RECEPTACLE COVERS, OR CABLE ENTRY

METHODS INTO ENCLOSURES WILL REQUIRE RANGE

TRAINING LAND PROGRAM, HUNTSVILLE CENTER

MANDA TORY CENTER OF EXPERTISE APPROVAL.

STUB UP CONDUIT AS CLOSE AS PRACTICAL TO CABLE

FITTING.

SEE SHEET E-09 FOR ADDITIONAL INFORMATION ON

MASTER TARGET DATA PANELS.

PROVIDE GROUNDING IN ACCORDANCE WITH

EMPLACEMENT GROUNDING DETAIL ON SHEET E-07.

US Army Corps of Engineers® u 0:

a.

<( e. f- 0: w w "' "'"' (!) Cf) Ow z

8:~~ a:: _J

O<.lc,i ~ ~ '.'izffi ~ >- w a, ;;: a:: Cl C)a,<( f- _J

~5g: z ~ ~U w ~ (.)

<ocn u. ir ~g~ ~ f- 0 :,:0: (!) (.)

~~~ z w > _J

WQ>- w C) u_J 0 z :, :,; <(:,;

0: 'ii.

ci i5

E-03

E

D

C

B

A

2 3 4

SEEN 19

PARTIAL MAT TARGET ELEVATION

NOTTO SCALE

NOTES:

1. CONDUIT TO EXTEND 5 FEET BEYOND EMPLACEMENT.

2. CABLES/CONDUITS ARE ROUTED FROM SIDE OF BERM TO

PREVENT CABLE DAMAGE DURING MAINTENANCE OF

BERM.

3. ROUTE UNDER SLAB. POWER AND DATA INSTALLED IN

SAME TRENCH.

4. EQUIPMENT SHALL NOT BE MOUNTED HIGHER THAN 2"

FROM TOP OF EMPLACEMENT WALL.

5. POWER TO DATA PANEL RECEPTACLE IN MTDP SHALL BE

ROUTED THROUGH SIGN LE POLE, SINGLE THROW

SWITCH.

6. ALL EQUIPMENT SHALL BE MOUNTED ON 1.625" DEEP

UNISTRUT. NO EQUIPMENT SHALL BE PERMITTED TO BE

INSTALLED DIRECTLY TO THE CONCRETE WALL.

7. NOTUSED.

8. TPR, APR AND DPR SHALL NOT BE GFCI PROTECTED.

9. PERMANENTLY LABEL THE EMPLACEMENT ACCORDING TO

THE CIVIL AND ELECTRICAL DESIGNATIONS.

10. PROVIDE SEAL FITTINGS AS SHOWN IN DETAIL ON SHEET

E-07 FOR ALL CABLE PENETRATIONS TO NEMA 4, 4X, OR 6P

RATED ENCLOSURES.

11 . INSTALL MYERS TYPE HUBS ON ALL CONDUIT

PENETRATIONS TO SIDE OF ENCLOSURE.

12. ALL DIMENSIONS SHOWN IN INCHES UNLESS OTHERWISE

NOTED.

13. IF TARGET IS BATTERY OPERATED WITH NO AC POWER

PROVIDED, THE TARGET GROUND ROD SHALL BE

INSTALLED WITH A 15' COILED #1 /0 AWG BARE COPPER

GROUND CABLE FOR FUTURE BONDING TO THE TARGET

MECHANISM.

14. PROVIDE TARGET AND AUXILIARY OUTLETS WITH NEMA

3R WET LOCATION COVERS MAKING OUTLETS SUITABLE

FOR USE IN WET LOCATIONS. SEE DETAIL SHEET E-07

FOR WET LOCATION COVER. IN USE COVERS WITH

COVERS INTENDED TO CLOSE OVER THE INSERTED CORD

ARE NOT ACCEPTABLE AS THESE COVERS WILL NOT

CLOSE OVER THE TARGET POWER OR AUXILIARY CORDS.

15. DEVIATIONS TO THE EQUIPMENT SIZES, EQUIPMENT

NUMBERS, RECEPTACLE COVERS, OR CABLE ENTRY

METHODS INTO ENCLOSURES WILL REQUIRE RANGE

TRAINING AND LAND PROGRAM HUNTSVILLE CENTER

MANDATORY CENTER OF EXPERTISE APPROVAL.

16. CONDUIT STUBBED UP AS CLOSE TO CABLE SEAL FITTING

AS POSSIBLE.

17. EQUIPMENT IS SHOWN AT THE PREFERRED MOUNTING

HEIGHT. UNDER NO CIRCUMSTANCE SHOULD ANY

EQUIPMENT BE INSTALLED SUCH THAT THE TOP OF THE

EQUIPMENT IS LESS THAN 2" FROM THE TOP OF THE

EMPLACEMENT WALL.

18. SEE SHEET E-09 FOR ADDITIONAL INFORMATION ON

MASTER TARGET DATA PANELS.

19. INSTALL NEW TARGET EQUIPMENT APPROXIMATELY 20 FT

FROM EXISTING MAT EQUIPMENT AND POWER CENTER

EQUIPMENT. EXTEND POWER AND DATA FROM POWER

CENTER DISTRIBUTION PANEL AND FIBER PATCH PANEL IN

PVC CONDUIT.

5 6 7

PANEL BOARD: MAT

235 MAIN

VOLTAGE: 240/120

LOAD SERVED

NO.

POLES

SURGE ARRESTOR 2

SPARE 1

SPACE

SPACE

SPACE

TOTAL VA PHASE A: 1950

TOTAL VA PHASE B: 1900

SUPPLIED FROM : TRSF-XX

#6 AWG BARE COPPER

CONDUCTOR

#1 /0 AWG BARE COPPER

CONDUCTOR EXOTHERMIC

WELD TO GROUND ROD

TARGET GROUND ROD

8 9 10

LOCATION: XXXXXXX MOUNTED: SURFACE FEED: BOTTOM

MAIN LUGS ONLY ASYM A. I.C MIN .. 10,000

PHASE: 1 WIRE: 3 RATING: NEMA3R

VA/ PHASE VA/ PHASE

TRIP WIRE

A B

CKT CKT

A B

WIRE TRIP NO.

LOAD SERVED AMPS SIZE NO. NO. SIZE AMPS POLES

--- 1900 MAT (NEMA L 14-20R,

---- --- 1 2 12 20 2 2-NEMA L5-20R) --- 1900

20 --- --- 5 6 50 12 20 1 TDPAND MR

7 8 --- --- 20 1 SPARE

9 10 1 SPACE

11 12 1 SPACE

0 0 1950 1900

TOTAL CONNECTED WATTAG E: 3,850

TOTAL DEMAND AMPS: 16

NEMA 3R

LOADCENTER

NEMA 4 MTDP / TDP

#1 /0 AWG BARE COPPER

CONDUCTOR, 15' COILED

ABOVE GROUND FOR

BONDING TO FUTURE

TARGET TRACK

PROVIDE CABLE SEAL FITTING FOR

GROUND CABLE PENETRATION

INTO DATA ENCLOSURE

GROUND ROD FOR TARGET TRACK

INSTALL 30 FT FROM MTDP.

#1/0 AWG BARE COPPER CONDUCTOR.

SEE EMPLACEMENT GROUNDING DETAIL.

EMPLACEMENT GROUNDING DETAIL

EQUIPMENT MOUNTED ON 1.625"

DEEP UNISTRUT. SEE NOTE 6.

NOTTO SCALE

TARGET POWER RECEPTACLE (TPR) 120/240V, 20A,

~tc!~fi'ci~b~v~ic~N<~i~~~~t~i~o111~~7}suRE.

AUXILIARY POWER RECEPTACLE (APR) 120V, 20A, 3 WIRE,

TWIST LOCK (NEMA L5-20R) WITH WET LOCATION COVER

IN WEATHERPROOF ENCLOSURE. SEE NOTES 4 & 14.

SEE NOTES 4 & 14.

SEE NOTE 9

SINGLE POLE, SINGLE THROW, 120V

SWITCH IN WEATHERPROOF ENCLOSURE

WITH COVER. SEE NOTES 4 & 5

SINGLE GANG 2 5/8" DEEP WEATHERPROOF

RIGID METAL CONDUIT ~g~ t1'~1HB'¢'t!W,ilf~i?N°cioiLANK covER

(TYPICAL)

GFCI MAINTENANCE RECEPTACLE (MR) IN

WEATHERPROOF ENCLOSURE WITH COVER

WALL MOUNTED NEMA 34

LOADCENTER. SEE NOTE 4.

#6 BARE COPPER

CONDUCTOR

#6 BARE COPPER CONDUCTOR

SEE NOTE 10

CONDUIT WITH ARMORED DATA CABLES.

SEE NOTES 1-3, 10, & 16

DATA POWER RECEPTACLE (DPR) LOCATED

INSIDE PANEL. SEE NOTE 9. RECEPTACLE

NOT SHOWN FOR CLARITY.

MAT TARGET ENLARGED ELECTRICAL EQUIPMENT ELEVATION

NOTTO SCALE

US Army Corps of Engineers® u 0:

a.

<( e.

0: f- (9 ~ ~

Cf) w Ou,z

8:~~ _J <:)

ll'.

OU(.') j::

'.'izffi~ w a,;;: 0 ll'.

(.')a,<( _J 0 ~5g: -,: :,;

~Uw (.) ll'.

<ocn ir -,:

~g~ f- <:)

0:,:0: (.) z ~~~ w > _J

UJQ>- w 0 (.')u_J :,; z :, 0: 'ii.

ci i5

E-04

E

D

C

B

A

2 3

SIT CLUSTER DATA OUTLETS.

SEE NOTE 15.

SINGLE POLE, SINGLE THROW, 120V

SWITCH IN WEATHERPROOF ENCLOSURE

WITH COVER. SEE NOTES 4 & 5.

GFCI MAINTENANCE RECEPTACLE (MR) IN

WEATHERPROOF ENCLOSURE WITH COVER

EQUIPMENT MOUNTED ON 1.625" DEEP

UNISTRUT. SEE NOTE 6.

WALL MOUNTED NEMA 3R

LOADCENTER. SEE NOTE 4

POWER CABLE FROM 120/240V

POWER SOURCE IN CONDUIT.

SEE NOTES 1-3

SAT EMPLACEMENT

POWER AND DATA

OUTLETS.

SEE NOTE 15.

SIT CLUSTER POWER OUTLETS.

SEE NOTE 15.

SAT EMPLACEMENT

ELECTRICAL EQUIPMENT

STATIONARY ARMOR TARGET ELEVATION

RIGID METAL CONDUIT.

TYPICAL

NOTTO SCALE

TARGET DATA PANEL (TDP) 2" CONDUIT

6 7

SIT CLUSTER POWER OUTLETS.

SEE NOTE 15.

SIT CLUSTER DA TA OUTLETS.

SEE NOTE 15.

MASTER TARGET DATA PANEL (MTDP)

LATCHED TYPE REMOVABLE LID.

CONTINUOUS HINGE WITH

RE MOVEABLE PIN. NEMA 4 TYPE

ENCLOSURE. SEE NOTES 4.

DATA POWER RECEPTACLE (DPR) LOCATED

INSIDE PANEL. RECEPTACL~

NOT SHOWN FOR CLARITY.

CONDUIT/CABLE SEAL FITTING.

SEE NOTE 18

8 9 10

NOTES:

1. RE-USE EXISTING CABLES CONDUITS WITH POWER AND

DATA CABLES ENTERING EMPLACEMENT.

2. INSTALL NEW CONDUIT HUB WITH CABLE SEAL FITTING IN

NEW MTDP. SEE DETAIL ON E-07.

3. PROTECT POWER AND DATA CABLES DURING

REMOVAL/DEMOLITION OF EXISTING DATA ENCLOSURE

LOADCENTER. RE-TERMINATE DATA CABLES IN NEW

MTDP ENCLOSURE AND POWER CABLES IN NEW

LOADCENTER.

4. EQUIPMENT SHALL NOT BE MOUNTED HIGHER THAN 2"

FROM TOP OF EMPLACEMENT WALL.

5. POWER TO DATA PANEL RECEPTACLE IN MTDP SHALL BE

ROUTED THROUGH SINGLE POLE, SINGLE THROW SWITCH.

6. ALL EQUIPMENT SHALL BE MOUNTED ON 1.625" DEEP

UNISTRUT. NO EQUIPMENT SHALL BE PERMITTED TO BE

INSTALLED DIRECTLY TO CONCRETE WALL.

7. FOR FLANK TYPE SAT TARGET INCREASE THE LENGTH OF

GROUND CABLE TO 18 FT.

8. TPR, APR AND DPR SHALL NOT BE GFCI PROTECTED.

9. PERMANENTLY LABEL THE EMPLACEMENT ACCORDING TO

THE CIVIL AND ELECTRICAL DESIGNATIONS.

10. PROVIDE SEAL FITTINGS AS SHOWN IN DETAIL ON SHEET

E-07 FOR ALL CABLE PENETRATIONS TO NEMA 4, 4X, OR 6P

RATED ENCLOSURES.

11 . INSTALL MYERS TYPE HUBS ON ALL CONDUIT

PENETRATIONS TO SIDE OF ENCLOSURE.

12. ALL DIMENSIONS SHOWN IN INCHES UNLESS OTHERWISE

NOTED.

13. PROVIDE TARGET AND AUXILIARY OUTLETS WITH NEMA

3R WET LOCATION COVERS MAKING OUTLETS SUITABLE

FOR USE IN WET LOCATIONS. SEE DETAIL SHEET E-07

FOR WET LOCATION COVER. IN USE COVERS WITH

COVERS INTENDED TO CLOSE OVER THE INSERTED CORD

ARE NOT ACCEPTABLE AS THESE COVERS WILL NOT

CLOSE OVER THE TARGET POWER OR AUXILIARY CORDS.

14. DEVIATIONS TO THE EQUIPMENT SIZES, EQUIPMENT

NUMBERS, RECEPTACLE COVERS, OR CABLE ENTRY

METHODS INTO ENCLOSURES WILL REQUIRE RANGE

TRAINING AND LAND PROGRAM HUNTSVILLE CENTER

MANDATORY CENTER OF EXPERTISE APPROVAL.

15. SEE SHEET E-06 FOR DETAILS ON SAT POWER AND DATA

OUTLETS, SIT POWER OUTLETS, AND SIT DATA OUTLETS.

16. SEE SHEET E-09 FOR ADDITIONAL INFORMATION ON

MASTER TARGET DATA PANELS.

17. MOUNT EQUIPMENT AS LOW AS POSSIBLE ON THE FRONT

WALL OF THE EMPLACEMENT. NO ELECTRICAL

EQUIPMENT SHALL BE INSTALLED WITHIN 2" OF THE TOP

OF THE EMPLACEMENT WALL.

18. CONDUIT/CABLE SEAL FITTING CONNECTION TO THE

MTDP. SEE CONDUIT/CABLE SEAL FITTING DETAIL ON

SHEET E-07.

19. EXISTING FIBER OPTIC CABLE ENCLOSURE. RE-USE

EXISTING ENCLOSURE. SEAL ALL OPENINGS WITH NEMA 4

RATED PLUGS. PROVIDE NEW CONDUIT INTO NEW MTDP

FOR TERMINATION OF EXISTING FIBER OPTIC CABLES

INSIDE NEW MTDP.

CONDUIT/CABLE SEAL FITTING.

SEE NOTE 18 PANEL BOARD: SAT-SIT CLUSTERLOCATI ON: XXXXXXX MOUNTED: SURFACE FEED: BOTTOM

POWER CABLE TO NEXT TARGET

EMPLACEMENT IN CONDUIT.

SEE NOTES 1-3.

WIRE GUTTER, SIZE PER NUMBER AND

SIZE OF CONDUCTORS IN EACH EMPLACEMENT

#6 AWG BARE COPPER CONDUCTOR, 1 O' COILED

ABOVE GROUND FOR BONDING TO FUTURE TARGET.

SEE NOTE 7.

CONDUIT FOR POWER TO LOAD

CENTER

CONDUIT FOR POWER TO EMPLACEMENT

POWER OUTLETS

#6 BARE COPPER CONDUCTOR

SEE NOTE 10

STATIONARY ARMOR TARGET

ELECTRICAL EQUIPMENT ELEVATION

NOTTO SCALE

CABLE SEAL FITTING.

SEE NOTE 10

#6 BARE COPPER CONDUCTOR

SEE NOTE 10

EXISTING FIBER OPTIC CABLE

ENCLOSURE. SEE NOTE 19.

125 MAIN

VOLTAGE: 240/120

LOAD SERVED

NO.

POLES

SURGE ARRESTOR 2

2-SITS(2-NEMA L 14-20R,

2-NEMA L5-20R) 2

2-SITS(2-NEMA L 14-20R,

2-NEMA L5-20R) 2

TOTAL VA PHASE A: 2951

TOTAL VA PHASE B: 2901

SUPPLIED FROM: TRSF-XX

MAIN LUGS ONLY

PHASE: 1 WIRE: 3

VA/ PHASE

TRIP WIRE

A B

CKT

AM PS SIZE NO.

---- --- 1 ...

20 12 788 5

788 7 788 9

20 12 788 11

1576 1576

ASYM A.I.C MIN. : 10,000

RATI NG: NEMA3R

VA/ PHASE

CKT

A B

WIRE TRIP NO.

LOAD SERVED NO. SIZE AM PS POLES

1325 SAT (NEMA L 14-20R,

2 12 20 2 2-NEMA L5-20R) 1325

6 50 12 20 1 TDPAND MR

8 ... ... 20 1 SPARE

10 ... ... 20 1 SPARE

12 1 SPAC E

1375 1325

TOTAL CONNECTED WATTAGE: 5,852

TOTAL DEMAND AM PS: 24

US Army Corps of Engineers® a::

lJ.J f-u (/)

0: I-' (l_ f- 0 :,; :,;

~ t;; <( e.

0:

(9 ~ ~ Cl) tij (9 Ou, z ..J(!)a::

8:~~ ;;: a::;::

OU(.') f- <( >- '.'izffi ~ lJ.J f- a::

a, ;;: 0 a:: f- (.')a,<( -'OZ ~5g: <( ::;; <( ~ U w Ua::u..

<ocn ii' <(~ ~g~ f- >- >- 0 :,:0: U a::a::

UJQ>- woo (.') u_J z :, i= i= <(:,;

0: -;j_ ;:: ;::

ci z i5 <(

E-05

F

E

D

C

B

A

I 2

FOR USE BY TARGET VENDOR. SEE NOTE 1. ..,

SINGLE GANG 2 5/8" DEEP WEATHERPROOF ~

BOX WITH WEATHERPROOF BLANK COVER

I 3 I 4 I 5

AUXILIARY POWER RECEPTACLE (APR), 120V, 20A, ~

3 WIRE, TWIST LOCK (NEMA L5-20R) IN '.

WEATHERPROOF ENCLOSURE WITH COVER. SEE

NOTES 2, 3, AND 4.

TARGET POWER RECEPTACLE (TPR\ 120/240V, 20A,

4 WIRE, TWIST LOCK (NEMA L 14-20R WITH WET

LOCATION COVER IN WEATHERPROOF ENCLOSURE

SEE NOTES 2, 3, AND 4 .

I 6

STATIONARY INFANTRY TARGET

CLUSTER DATA OUTLETS ELEVATION

STATIONARY INFANTRY TARGET

CLUSTER POWER OUTLETS ELEVATION

NOTTO SCALE

PROVIDED THIS CONTRACT + PROVIDED BY TARGET CONTRACT

,-= ____ ;__ __ ,-::::::~:c---;;~ 0 0 • ----Q)

SINGLE GANG, DEEP,

WEATHERPROOF

OUTLET BOX

Q)

L----

SEALING GASKET WEATHERPROOF AMPHENOL AMPHENOL

COVER JE18 RJF21G

GASKET ETHERNET

NOTES:

CONNECTOR

1. CONSTRUCTION CONTRACTOR TO PROVIDE BLANK

WEATHERPROOF COVER. ALL OPENINGS IN COVER FOR

WEAHTERPROOF DATA CONNECTOR WILL BE DONE BY

THE TARGET VENDOR DURING THE TARGET

INSTALLATION.

DATA OUTLET RESPONSIBILITY

REFERENCE DETAIL

NOTTO SCALE

AMPHENOL

RJFC6G

OUTLET CAP

NOTTO SCALE

I 7 I 8 I 9 I 10

FOR USE BY TARGET VENDOR. SEE NOTE 1. ..,

SINGLE GANG 2 5/8" DEEP WEATHERPROOF ~

BOX WITH WEATHERPROOF BLANK COVER

i • r AUXILIARY POWER RECEPTACLE (APR), 120V, 20A, 3 WIRE, TWIST LOCK (NEMA L5-20R) IN

WEATHERPROOF ENCLOSURE WITH COVER. SEE

NOTES 2, 3, AND 4.

TARGET POWER RECEPTACLE (TPR) 120/240V, 20A,

4 WIRE, TWIST LOCK (NEMA L 14-20R) WITH WET

LOCATION COVER IN WEATHERPROOF ENCLOSURE

SEE NOTES 2, 3, AND 4.

STATIONARY ARMOR TARGET

POWER AND DATA OUTLETS ELEVATION

NOTTO SCALE

NOTES:

1.

2.

TARGET DATA OUTLET SHALL HAVE 6" -12" OF CAT 6

CABLE COILED AND TERMINATED WITH A MAIL RJ-45

CONNECTOR. INSTALL SEALING GASKET AND

WEATHERPROOF COVER. ALL OTHER DATA OUTLET

RQUIREMENTS WILL BE INSTALLED BY TARGET VENDOR

UNDER A SEPER.ATE COTRACT. SEE DATA OUTLET

RESPONSIBILITY REFERENCE DETAIL FOR MORE

INFORMATION ON HOW DATA OUTLET WILL BE INSTALLED.

ALL OUTLETS SHALL BE MOUNTED ON THE EMPLACEMENT

WALL AS LOW AS POSSIBLE. UNDER NO CIRCUMSTANCE

SHALL THE OUTLETS BE INSTALLED WITHIN 2" FROM THE

TOP OF THE EMPLACEMENT WALL.

3. TARGET POWER OUTLETS AND AUXILIARY POWER

OUTLETS SHALL NOT BE GFCI PROTECTED.

4. PROVIDE TARGET AND AUXILIARY OUTLETS WITH NEMA 3R

WET LOCATION COVERS MAKING OUTLETS SUITABLE FOR

USE IN WET LOCATIONS. SEE DETAIL SHEET E-07 FOR

WET LOCATION COVER. IN USE COVERS WITH COVERS

INTENDED TO CLOSE OVER THE INSERTED CORD ARE NOT

ACCEPTABLE AS THESE COVERS WILL NOT CLOSE OVER

THE TARGET POWER OR AUXILIARY CORDS.

US Army Corps of Engineers®

<I)"' "'w w >w z z w

- u ~ b:

0 Q.

<I) <I) Q.

"'°" 8 <!)

:, "' "'w <I) 0 u 0:

Q.

< e.

0:

(9 ~ ~ Owz

8:~~

OU<!)

'.'izffi~ a,,::

"'"'" ~5g:

~Uw «o<ll ~g~ 0:,:0:

WQ>-

<!Ju.J z ::, 0: -;j_ i5

-w N U) a::

lJ.J f-

I -' f- 0

~t;;

Cl) tij (9 _J (!) a::

;;:a::;::

f- <( >-lJ.J f- a::

0 a:: f- -'Oz <( ::;; <( Ua::u._ ii'<(~ f- >- >-Ua::a::

~~~ woo i= i= ;::;::

z

E-06

E

D

C

B

A

WEATHERPROOF EXTERIOR

ENCLOSURE

2 3

LID SPRINGS CLOSED

WHEN PLUG NOT

INSERTED

RUBBER GASKET

NOTE:

WEATHERPROOF, IN-USE WET LOCATION COVERS SHALL BE PROVIDED

WITH ETHYLENE PROPYLENE RUBBER GASKETS AROUND THE FACE OF

THE RECEPTACLE TO PREVENT THE ENTRANCE OF MOISTURE AND DIRT

WITH COVER OPEN AND PLUG INSERTED. COVER SHALL ACCEPT MALE

PLUG WITH DIAMETER OF 1.8" - 1.95".

WET LOCATION RECEPTACLE COVER

NOTTO SCALE

NEMA3R

LOADCENTER

NEMA 4 MTDP / TDP

LOCKNUT

BOTTOM OF

DATA ENCLOSURE

CABLE SEAL FITTING

MAIN BODY

NEOPRENE BUSHING

CABLE SEAL FITTING

GLAND NUT

CONDUIT

PROVIDE CABLE SEAL FITTING

#6 AWG BARE COPPER

CONDUCTOR EXOTHERMIC

WELD TO GROUND ROD

TARGET GROUND ROD

NOTE:

FOR GROUND CABLE PENETRATION

INTO DATA ENCLOSURE

#6 AWG BARE COPPER CONDUCTOR,

10' (FOR MITS AND SATS)AND 6' (FOR

SITS) COILED ABOVE GROUND FOR

BONDING TO FUTURE TARGET

THIS DETAIL DEPICTS GROUNDING REQUIREMENTS FOR SITS, SATS,

AND MITS. SEE SHEET E-4 FOR MAT GROUNDING DETAIL.

EMPLACEMENT GROUNDING DETAIL

NOTTO SCALE

5 6 7

CABLE SEAL FITTING DETAIL

NOTTO SCALE

8 9 10

EXISTING FIBER OPTIC CABLE

CABLE SEAL FITTING

GLAND NUT

NEOPRENE BUSHING

CABLE SEAL FITTING

MAIN BODY

BOTTOM OF DATA ENCLOSURE

THREADED REDUCING BUSHING AS

NEEDED TO REDUCE CONDUIT SIZE

TO CABLE SEAL FITTING SIZE

(NOT SHOWN)

RIGID COUPLING

EXISTING CONDUIT

CONDUIT/ CABLE SEAL FITTING DETAIL

NOTTO SCALE

US Army Corps of Engineers® u 0:

a. f-:,; :,; z

<( e. w 0:

(9 ~ ~

Ou,z w Cf)

8:~~ (.) _J

<{ ~ OU(.') _J

'.'izffi~ CL w a,;;:

:;; Cl (.')a,<( w _J

~5g: f- <{ ~Uw w (.)

<ocn (!) ir ~g~ a:: f- 0:,:0: ~ (.)

~~~ w _J _J

UJQ>- <{ w (.')u_J (.)

z :, a: <(:,;

0: "ii. >-f-ci i5

E-07

E

D

C

B

A

2 3 4 5 6

TYPICAL MASTER TARGET DATA PANEL (MTDP) DETAIL AT TARGET EMPLACEMENT

NOTTO SCALE

KEYED NOTES REPRESENTED WITH@:

1. ENCLOSURE SHALL BE 16 GAUGE MINIMUM GALVANIZED STEEL SHEET METAL WITH

WALL MOUNT BRACKETS. ENCLOSURE SHALL CARRY A NEMA 4 RATING AND BE

TESTED BY UL OR OTHER APPROVED TESTING AGENCY.

2. PROVIDE ENCLOSURE WITH FAST OPERATING CLAMP ASSEMBLY. BOLT TYPE CLAMPS

ARE NOT ACCEPTABLE.

3. INJECTION-MOLDED PLASTIC CONNECTOR 12 PORT PATCH PANEL.

4. METAL BACK PLATE TO SECURE COMPONENTS INSIDE ENCLOSURE.

5. 6-STRAND ARMORED TYPE FIBER OPTIC CABLE(S) WITH CENTRAL STRENGTH

MEMBER. SECURE FIBER OPTIC CABLE CENTRAL MEMBER INSIDE MTDP ENCLOSURE.

6. METALLIC CABLE SHEATH GROUNDING CLAMP AND GROUNDING CONNECTOR, BOND

CABLE ARMOR/SHIELD TO MTDP BACK PLATE GROUNDING BAR. ALL GROUND CABLES

NOT SHOWN FOR CLARITY.

7. CENTRAL MEMBER STRAIN-RELIEF BRACKET.

8. GROUND BAR - SECURE TO METAL BACK PLATE.

9. #6 AWG BARE COPPER GROUNDING CONDUCTOR.

10. DATA PANEL RECEPTACLE (DPR)- 20 AMP, 125 VOLT, 2 POLE, 3 WIRE GROUNDING

TYPE IN A STANDARD SINGLE-GANG METAL BOX AND GALVANIZED STEEL DEVICE

PLATE. CONNECT DPR AHEAD OF GFCI MAINTENANCE RECEPTACLE TO AVOID

NUISANCE TRIPPING.

11. 2/C #12 WITH GROUND CORD IN CONDUIT FROM CIRCUIT BREAKER LOADCENTER FOR

120 VOLT, 1-PHASE SERVICE TO DUPLEX RECEPTACLE. RECEPTACLE SHALL NOT BE

FED FROM ANY GROUND FAULT INTERRUPTING DEVICE.

12. FIELD INSTALLABLE "SC" CONNECTORS WITH BEND PROTECTOR. ALL CONNECTORS

NOT SHOWN FOR CLARITY.

13. FIBER OPTIC CABLE BUFFER TUBES WITH 6-STRANDS OF FIBER, EACH. PROVIDE 2'

SLACK EACH END.

14. NOT USED.

15. WALL MOUNTED SINGLE PANEL HOUSING FOR FIBER OPTIC CABLE TERMINATIONS.

FIBER OPTIC BUFFER TUBE SLACK AND FAN OUT KIT SHALL BE CONTAINED WITHIN

HOUSING. HOUSING SHALL BE COMPATIBLE WITH 12 PORT PATCH PANEL.

16. NOT USED.

17. PROVIDE MYERS HUB TYPE FITTING AT CONDUIT PENETRATION.

18. MTDP SHALL HAVE A ROLLED FLANGE AROUND PERIMETER OF OPENING.

19. PROVIDE ONE CABLE SEAL FITTING FOR EACH CABLE. SEE TYPICAL CABLE SEAL

FITTING DETAIL ON SHEET E-07.

20. EXISTING CONDUIT FOR FIBER OPTIC CABLES.

21 . CONDUIT/CABLE SEAL FITTING CONNECTION TO THE MTDP. SEE CONDUIT/CABLE

SEAL FITTING DETAIL ON SHEET E-07.

22. HINGED COVER WITH CORROSION - RESISTANT STAINLESS STEEL CAPTIVE CLAMPS.

HINGE MUST HAVE REMOVABLE PIN. PROVIDE A SEAMLESS FOAM-IN-PLACE GASKET

FOR A WATERTIGHT AND DUST TIGHT SEAL.

23. FIBER OPTIC FAN-OUT KIT OR SPLICE KIT WITH PIGTAILS.

24. PROVIDE 14" X 10" SPACE FOR INSTALLATION OF TARGET COMMUNICATIONS

EQUIPMENT. POWER OUTLET AND GROUND LUG ARE ONLY COMPONENTS INSTALLED

IN THIS SPACE THAT IS NOT BY THE TARGET VENDOR. AREA MEASURED FROM SIDE

OF ENCLOSURE NOT EDGE OF BACKPLATE.

7 8 9

MASTER TARGET DATA PANEL

(MTDP)

- - - - - - - - - - - - - - - - - - - - - - - - - .£""® -I

, MTDP BACKPLATE

~~-----------7 ~@~ ' I ~~ I

~-c=J ___ _

-c::J ,-~J

~i- ---------- _I tj ETHERNET

I SWITCH

GROUND

LUGS

mm d I d I

1-d L ___ _

L .. - .. - .. - .. - .. - .. - . --1- -_-.: :.-.: :.--= :...-J -

MTDP DATA WIRING SCHEMATIC

PROVIDED BY MCA CONTRACTOR

• - - - - - - - - PROVIDED BY OPA CONTRACTOR

GENERAL NOTES:

1. THIS DETAIL ONLY APPLIES FOR THE STATIONARY TARGET EMPLACEMENTS (SIT).

2. TERMINATE ALL FIBER OPTIC CABLES ENTERING OR LEAVING WITH "SC" CONNECTORS. ALL 6

STRANDS OF FIBER ARE REQUIRED TO BE TERMINATED AT EACH EMPLACEMENT.

3. PROVIDE CABLE IDENTIFICATION DIRECTORY ON INSIDE OF COVER.

4. LABEL ALL CABLES WITH ADHESIVE POLYETHYLENE WRAP AROUND LASER PRINTED LABELS

INDICATING CABLE DESTINATION AND CABLE TYPE.

5. MASTER TARGET DATA PANEL (MTDP) SHALL BE 24"W X 12"H X 6"D.

ml US Army Corps of Engineers® w N U) iii u Ir al z z iii

U) ...

z w u :;;;

w

0: () a. <( :,; " _J <( e. Q_ 0: :;;;

(9 ~ ~ Ou,z U) w 8:~~ _J ...

OU<!) ~ ci5 '.'izffi~ w _.:, a,;;: 0 w <!)a,<( _J z ~5g: <( <( ~Uw () Q_ <ocn ir <( ~g~ ...

~ 0:,:0: ()

~~~ w 0 _J ... UJQ>- w w <!Ju.J z :, ('.)

<(" ~ 0: 'ii. <( 0 ~ i5 w ...

U)

E-08

E

D

C

B

A

2 3 4 5 6

TYPICAL MASTER TARGET DATA PANEL (MTDP) DETAIL AT TARGET EMPLACEMENT

NOTTO SCALE

KEYED NOTES REPRESENTED WITH@:

1. ENCLOSURE SHALL BE 16 GAUGE MINIMUM GALVANIZED STEEL SHEET METAL WITH

WALL MOUNT BRACKETS. ENCLOSURE SHALL CARRY A NEMA 4 RATING AND BE

TESTED BY UL OR OTHER APPROVED TESTING AGENCY.

2. PROVIDE ENCLOSURE WITH FAST OPERATING CLAMP ASSEMBLY. BOLT TYPE CLAMPS

ARE NOT ACCEPTABLE.

3. INJECTION-MOLDED PLASTIC CONNECTOR 12 PORT PATCH PANEL.

4. METAL BACK PLATE TO SECURE COMPONENTS INSIDE ENCLOSURE.

5. 6-STRAND ARMORED TYPE FIBER OPTIC CABLE(S) WITH CENTRAL STRENGTH

MEMBER. SECURE FIBER OPTIC CABLE CENTRAL MEMBER INSIDE MTDP ENCLOSURE.

6. METALLIC CABLE SHEATH GROUNDING CLAMP AND GROUNDING CONNECTOR, BOND

CABLE ARMOR/SHIELD TO MTDP BACK PLATE GROUNDING BAR. ALL GROUND CABLES

NOT SHOWN FOR CLARITY.

7. CENTRAL MEMBER STRAIN-RELIEF BRACKET.

8. GROUND BAR - SECURE TO METAL BACK PLATE.

9. #6 AWG BARE COPPER GROUNDING CONDUCTOR.

10. DATA PANEL RECEPTACLE (DPR)- 20 AMP, 125 VOLT, 2 POLE, 3 WIRE GROUNDING

TYPE IN A STANDARD SINGLE-GANG METAL BOX AND GALVANIZED STEEL DEVICE

PLATE. CONNECT DPR AHEAD OF GFCI MAINTENANCE RECEPTACLE TO AVOID

NUISANCE TRIPPING.

11. 2/C #12 WITH GROUND CORD IN CONDUIT FROM CIRCUIT BREAKER LOADCENTER FOR

120 VOLT, 1-PHASE SERVICE TO DUPLEX RECEPTACLE. RECEPTACLE SHALL NOT BE

FED FROM ANY GROUND FAULT INTERRUPTING DEVICE.

12. FIELD INSTALLABLE "SC" CONNECTORS WITH BEND PROTECTOR. ALL CONNECTORS

NOT SHOWN FOR CLARITY.

13. FIBER OPTIC CABLE BUFFER TUBES WITH 6-STRANDS OF FIBER, EACH. PROVIDE 2'

SLACK EACH END.

14. NOT USED.

15. WALL MOUNTED SINGLE PANEL HOUSING FOR FIBER OPTIC CABLE TERMINATIONS.

FIBER OPTIC BUFFER TUBE SLACK AND FAN OUT KIT SHALL BE CONTAINED WITHIN

HOUSING. HOUSING SHALL BE COMPATIBLE WITH 12 PORT PATCH PANEL.

16. NOT USED.

17. PROVIDE MYERS HUB TYPE FITTING AT CONDUIT PENETRATION.

18. MTDP SHALL HAVE A ROLLED FLANGE AROUND PERIMETER OF OPENING.

19. PROVIDE ONE CABLE SEAL FITTING FOR EACH CABLE. SEE TYPICAL CABLE SEAL

FITTING DETAIL ON SHEET E-07.

20. CONDUIT FOR FIBER OPTIC CABLES.

21 . NOTUSED

22. HINGED COVER WITH CORROSION - RESISTANT STAINLESS STEEL CAPTIVE CLAMPS.

HINGE MUST HAVE REMOVABLE PIN . PROVIDE A SEAMLESS FOAM-IN-PLACE GASKET

FOR A WATERTIGHT AND DUST TIGHT SEAL.

23. FIBER OPTIC FAN-OUT KIT OR SPLICE KIT WITH PIGTAILS.

24. PROVIDE 14" X 10" SPACE FOR INSTALLATION OF TARGET COMMUNICATIONS

EQUIPMENT. POWER OUTLET AND GROUND LUG ARE ONLY COMPONENTS INSTALLED

IN THIS SPACE THAT IS NOT BY THE TARGET VENDOR. AREA MEASURED FROM SIDE

OF ENCLOSURE NOT EDGE OF BACKPLATE.

8 9

MASTER TARGET DATA PANEL

(MTDP)

-~--------------------------1

MTDP BACKPLATE ,

~@~ i-----------1c

- - - -1~-j :- - - - - - - - - - -~

I :1 [;:=i- - _J

I ETHERNET p

SWITCH I

b I b I b-1 ____ _j

GROUND

LUGS

mm _ l-_: :...-_: :...-_::...-_:·I- •• - •• - •• - •• - •• - •• - •• .J

MTDP DATA WIRING SCHEMATIC

PROVIDED BY MCA CONTRACTOR

• - - - - - - - - PROVIDED BY OPA CONTRACTOR

GENERAL NOTES:

1. TERMINATE ALL FIBER OPTIC CABLES ENTERING OR LEAVING WITH "SC" CONNECTORS. ALL 6

STRANDS OF FIBER ARE REQUIRED TO BE TERMINATED AT EACH EMPLACEMENT.

2. PROVIDE CABLE IDENTIFICATION DIRECTORY ON INSIDE OF COVER.

3. LABEL ALL CABLES WITH ADHESIVE POLYETHYLENE WRAP AROUND LASER PRINTED LABELS

INDICATING CABLE DESTINATION AND CABLE TYPE.

4. MASTER TARGET DATA PANEL (MTDP) SHALL BE 24"W X 12"H X 6"D.

5. ALL COMPONENTS INSTALLED INSIDE MTDP ENCLOSURES SHALL BE SECURED BY

MECHANICAL MEANS. ADHESIVES ARE NOT ALLOWED FOR SECURING COMPONENTS INSIDE

MTDP ENCLOSURES.

US Army Corps of Engineers® w N U) iii u Ir al z z iii

U) w _J al u (.)

0: (.)

a. f'.C :,; " <( e. Q_

0: 0 (9 ~ ~

U) c,:

Ou,z w 8:~~ _J al

OU<!) u::

'.'izffi~ w _.'., a,;;: 0 <!)a,<( _J w ~5g: <{ z

~Uw (.)

Q_ <ocn ir ~g~ f- <{

0:,:0: (.) ~ ~~~ w 0 _J

UJQ>- w f- <!Ju.J w z :, (!)

0: 'ii.

c,:

>- f- 0 c,:

i5 w f- U)

E-09

E

D

C

B

A

2 3 4 5 6

TYPICAL FACADE/CLUSTER MASTER TARGET DATA PANEL (MTDP) DETAIL AT TARGET EMPLACEMENT

NOTTO SCALE

KEYED NOTES REPRESENTED WITH@:

1.

2.

3.

4.

5.

ENCLOSURE SHALL BE 16 GAUGE MINIMUM GALVANIZED STEEL SHEET METAL WITH

WALL MOUNT BRACKETS. ENCLOSURE SHALL CARRY A NEMA 4 RATING AND BE

TESTED BY UL OR OTHER APPROVED TESTING AGENCY.

PROVIDE ENCLOSURE WITH FAST OPERATING CLAMP ASSEMBLY. BOLT TYPE

CLAMPS ARE NOT ACCEPTABLE. TYPICAL FOR BOTH ENCLOSURES.

INJECTION-MOLDED PLASTIC CONNECTOR 12 PORT PATCH PANEL WITH SUPPORT

BRACKETS FOR FIELD INSTALLABLE SC CONNECTORS.

METAL BACK PLATE TO SECURE COMPONENTS INSIDE ENCLOSURE.

~li:~~D tr~1?tn1JJ~'b~~~~~~[f cii,~irn~i~~~~JJ\~~ ~lllPNmtLOSURE

6. METALLIC CABLE SHEATH GROUNDING CLAMP AND GROUNDING CONNECTOR, BOND

CABLE ARMOR/SHIELD TO MTDP BACK PLATE GROUNDING BAR. ALL GROUND

CABLES NOT SHOWN FOR CLARITY.

7. CENTRAL MEMBER STRAIN-RELIEF BRACKET.

8. GROUND BAR - SECURE TO METAL BACK PLATE. BOND ALL GROUND BARS

TOGETHER WITH A #6 AWG COPPER GROUND CONDUCTOR. GROUND CONDUCTOR

NOT SHOW IN THIS DETAIL.

9. #6 AWG BARE COPPER GROUNDING CONDUCTOR.

10. DATA PANEL RECEPTACLE (DPR)- 20 AMP, 125 VOLT, 2 POLE, 3 WIRE GROUNDING

TYPE IN A STANDARD SINGLE-GANG METAL BOX AND GALVANIZED STEEL DEVICE

PLATE. CONNECT DPR AHEAD OF GFCI MAINTENANCE RECEPTACLE TO AVOID

NUISANCE TRIPPING.

11. 2/C #12 WITH GROUND CORD IN CONDUIT FROM SINGLE POLE SINGLE THROW

SWITCH FOR 120 VOLT, 1-PHASE SERVICE TO DUPLEX RECEPTACLE. SEE TARGET

EMPLACEMENT ELECTRICAL DETAIL FOR SWITCH LOCATIONS.

12. FIELD INSTALLABLE "SC" CONNECTORS WITH BEND PROTECTOR. ALL CONNECTORS

NOT SHOWN FOR CLARITY.

13. FIBER OPTIC CABLE BUFFER TUBES WITH 6-STRANDS OF FIBER, EACH. PROVIDE 2'

SLACK EACH END, COIL AROUND RADIUS CONTROL GUIDES.

14. INDOOR/OUTDOOR RATED CATEGORY 6 CABLES TO TARGET DATA OUTLETS. COIL 3'

SLACK IN MTDP. COIL 6"-12" OF CABLE IN TARGET OUTLET AND TERMINATE CABLE

WITH MALE RJ-45 CONNECTOR. SAT-SIT CLUSTER EMPLACEMENTS MAY HAVE AS

MANY AS 5 CAT 6 DATA CABLES SERVING TARGET MECHANISMS. ONLY ONE CABLE

SHOWN ON THIS DETAIL FOR CLARITY.

15. WALL MOUNTED SINGLE PANEL HOUSING FOR FIBER OPTIC CABLE TERMINATIONS.

FIBER OPTIC BUFFER TUBE SLACK AND FAN OUT KIT SHALL BE CONTAINED WITHIN

HOUSING. HOUSING SHALL BE COMPATIBLE WITH 12 PORT PATCH PANEL.

16. PROVIDE MODULAR JACK WITH 110 BLOCKS ON LINE SIDE AND RJ45 OUTLETS ON

EQUIPMENT SIDE TO TERMINATE CAT 6 CABLES ENTERING OR EXITING ENCLOSURE.

17. 2" CONDUIT WITH MYERS HUBS WHERE CONDUIT PENETRATES EACH ENCLOSURE.

CONDUIT USE BY TARGET INSTALLER.

18. MTDP SHALL HAVE A ROLLED FLANGE AROUND PERIMETER OF OPENING.

19. PROVIDE ONE CABLE SEAL FITTING FOR EACH CABLE. SEE "TYPICAL CABLE SEAL

FITTING DETAIL," SHEET E-07.

20. NOT USED.

21. CONDUIT WITH CAT 6 CABLES, SEE TARGET EMPLACEMENT PLAN AND ELEVATION.

22. HINGED COVER WITH CORROSION-RESISTANT STAINLESS STEEL CAPTIVE CLAMPS.

HINGE MUST HAVE REMOVABLE PIN . PROVIDE A SEAMLESS FOAM-IN-PLACE GASKET

FOR A WATERTIGHT AND DUST TIGHT SEAL.

23. FIBER OPTIC FAN-OUT KIT OR SPLICE KIT WITH PIGTAILS.

24. PROVIDE MYERS HUB FITTING AT CONDUIT PENETRATION.

25. CONDUIT/CABLE SEAL FITTING CONNECTION TO THE MTDP. SEE CONDUIT/CABLE

SEAL FITTING DETAIL ON SHEET E-07.

7 8 9 10

TARGET DATA PANEL (MASTER) TARGET DATA PANEL

SEE GENERAL NOTE 4 SEE GENERAL NOTE 4

TYPICAL

r- - - -1~ --------- -1 I -------f~ - - - - - - - - - _,-,-_-__ -_-_-_

-c:: = = = = = = = = = = = ,--L..c::

t ------ I 1 r=--=--=--= b------C ~--'II I L ____ _J I I

I -::-..=-..=-..=-..=-~ I p------c! ~---· I L ____ _J b-1 ____ _J

I I I

TO LOCAL 1

TARGET - - _J

MECHANISM

..=- ..=- ..=- 7 -1 I --7 I I I

I I I I I I I I I I I

I

MTDP DATA WIRING SCHEMATIC

PROVIDED BY MCA CONTRACTOR

• - - - - - - - - PROVIDED BY OPA CONTRACTOR

GENERAL NOTES:

1. TERMINATE ALL FIBER OPTIC CABLES ENTERING OR LEAVING WITH "SC" CONNECTORS. ALL 6

STRANDS OF FIBER ARE REQUIRED TO BE TERMINATED AT EACH EMPLACEMENT.

2. PROVIDE CABLE IDENTIFICATION DIRECTORY ON INSIDE OF COVER.

3. LABEL ALL CABLES WITH ADHESIVE POLYETHYLENE WRAP AROUND LASER PRINTED LABELS

INDICATING CABLE DESTINATION AND CABLE TYPE.

4. TARGET DATA PANEL ENCLOSURES SHALL BE 16"W X 12"H X 6"D. MATER TARGET DATA PANEL

ENCLOSURES SHALL BE 24"W X 12"H X 6"D.

5. ALL COMPONENTS INSTALLED INSIDE MTDP ENCLOSURES SHALL BE SECURED BY

MECHANICAL MEANS. ADHESIVES ARE NOT ALLOWED FOR SECURING COMPONENTS INSIDE

MTDP ENCLOSURES.

US Army Corps of Engineers®

_J w z u <(

0..

0: <( a.

<( e. <( 0: 0 (9 ~ ~ (/) >- (/) Ou, z

8:~~ _J w w ;;: (.') _, OU(.') >- D:'. Ol

'.'izffi ~ w <( <( a, ;;: 0 >- (.)

(.')a,<( _JD:'.(.)

~5g: ~~~ ~Uw <ocn D:'. <( 0 ~g~ >- :a D:'.

0 :,:0: Uo::w ~~~ ~ w £Q UJQ>- w >- lJ._ (.') u_J (/) z :, ::::, <(:,; _J 0: 'ii. ~ >-ci 0 i5 <( lJ._

E-10