Energenics Lint Scrubber.pdf

www.energenics.com

1470 Don Street Naples, Florida 34104 Telephone: (239) 643-1711 Fax: (239) 643-6081 Customer Service: (800) 944-1711

Installation & Operation Manual for Energenics AALF Lint Scrubbers – All Models

Table of Contents Page 1

Receiving and Installation Page 2

Description of Lint Scrubber Operation Page 3

Important Installation Considerations Page 4

Typical Installation over Ironer/Folder – LS-6000 Page 5

Typical Installation over Ironer/Folder – LS-8000 Page 6

Dimensions – Side View – LS-6000 Page 7

Dimensions – End View – LS-6000 Page 8

Dimensions – Side View – LS-8000 Page 9

Dimensions – End View – LS-8000 Page 10

Operation of UL® Control Page 11

Changing the Filter Media – All Models Page 12

Filter Media Routing Diagram & Warning - LS-6000 Page 13

Filter Media Routing Diagram & Warning - LS-8000 Page 14

Warranty Statement Page 15

Changing the Filter Material Roll

CAUTION: FAILURE TO REPLACE SOILED MEDIA TAKEUP

ROLL WITH NEW TAKE-UP ROLL MAY RESULT IN GEAR

MOTOR FAILURE!

The filter material roll has 50 yards of material. The roll needs to be changed in two instances:

1. The entire roll of clean media is rolled up with lint on the lint take-up tube, filled with lint.

2. The lint blanket being rolled up by the lint take-up tube is too large and rubs against the top of the machine and can no longer advance. Cut the media along the clean part for reattachment using one of the extra rolls supplied with the Lint Scrubber.

To Change the Media Roll:

1. Follow the Diagram on Pages 13 & 14 for illustration.

2. Open the red handle, pulling the pin out of the roll.

3. Slide the roll toward the red handle end and off the drive. Discard the full lint take-up roll in an environmentally acceptable manner.

4. Put the new take up roll in place of the discarded roll. Slide onto the pin drive end. Align the other end with the red handle pin and insert in the roll.

5. If the take up roll was too large and discarded before all the clean media was expended, re-attach the clean media to the two sided tape on the take-up roll.

6. Manually advance the media until tight.

COttman Text Box 1..

COttman Text Box Check to see if the filter media is close to needing replaced (3/4 full). If so note on the report.

COttman Text Box 2.

COttman Text Box Check that the drive unit is functioning proper and that the drive spine is not stripped

COttman Text Box 3.

COttman Text Box Clean Unit to ensure all filters, screens and motors are clear and free of lint or debris

LIMITED WARRANTY & DISCLAIMER STANDARD CONDITIONS OF SALES

Energenics Corporation (herein called Energenics) warrants to the original purchaser, & to the original purchaser alone, its products to be free from defects in material and workmanship under normal use & service for a period of twenty-four

(24) months from the date of shipment. Energenics’ obligations under this warranty shall be limited solely to the repair or replacement of such parts, which Energenics examination shall disclose to Energenics satisfaction to have been thus defective & to the shipment of the repaired or replacement part or parts to the original purchaser F.O.B. point of shipment. In no event shall Energenics be liable for any consequential, incidental or special damages of any kind caused by the defect. The Warranty set forth shall not apply to & Energenics shall not be responsible for any equipment or part, which has been repaired or altered in any way, regardless of how or why the part was altered or repaired nor for any equipment or part, which has been subjected to the negligence or accident, improper use or care, nor for equipment or part with respect to which Energenics instructions relating to installation, maintenance, or use have not been followed.

This limited warranty is expressly made in lieu of all other warranties, expressed or implied, and in lieu of all other obligations or liabilities on the part of Energenics.

The purchaser by acceptance of the delivery of any part or product from Energenics agrees to indemnify Energenics & to hold it harmless against any liability, which may arise if the part or product received is mis-applied, improperly installed, improperly maintained, misused or abused, altered or rendered partially or totally inoperative due to any cause.

RETURNS: Merchandise may not be returned unless an RMA is obtained from Energenics.

A copy of the RMA must accompany the returned item as the packing Slip.

Energenics will assume no responsibility for merchandise returned neither without such prior approval nor for any charges or expenses incurred therewith.

CANCELLATIONS: Any order may be cancelled by the purchaser only upon written notice & upon payment to Energenics of reasonable & proper cancellation charges.

SALES & SIMILAR TAXES: Energenics prices do not include sales, use, gross receipts, excise or similar taxes, license fees & export or import duties. All taxes or other charges assessed to Energenics by reason of a transaction with the Purchaser must be paid by the Purchaser.

PRICE POLICY: All sales are made F.O.B. point of shipment. All prices are subject to change without notice.

DESIGN CHANGES: Energenics reserves the right to make changes in the design & changes or improvements in its products without notice or without imposing any obligation upon Energenics to install the same upon products heretofore manufactured.

GENERAL: No alteration, modification or extension of the foregoing conditions shall be binding upon Energenics unless made in writing & signed by an officer of Energenics.