Atch7-1_Equipment Data and Cut Sheets Logistics Category A.pdf

Submittal: ISSUED FOR CONSTRUCTION

Submittal Date: 12/23/2019

FY18 Misawa AB Hospital Renovation

Misawa AB Japan, Client: CDM Smith-TigerbrainBasis of Design Equipment Data and Cut Sheets Logistics Category A

Basis of Design Equipment Data and Cut Sheets

CDM Smith-Tigerbrain

Misawa AB Japan

FY18 Misawa AB Hospital Renovation

FA8903-15-D-0004 TO: 18-F-0072 / 021-10129-000

Logistics Category A

ISSUED FOR CONSTRUCTION

12/23/2019

1392090220U Text Box Attachment 7-1 to RFP No. FA520521R0003

UTILITIY REQUIREMENTS

From: Military Standard 1691 Construction and Material Schedule for Medical, Dental, Veterinary and Medical Research Laboratories December 1, 2016

SECTION 2: SCHEDULE OF TERMS

Joint Schedule Number (JSN). The Joint Schedule Number (JSN) is the alpha numeric designation used to identify FF&E during planning, design and activation activities in support of MHS/DVA healthcare facility requirements development. The number consists of an alpha character followed by four additional characters. The first alpha character denotes the commodity group as follows:

A Architectural C Fixed Casework D Dental Equipment and Casework E Modular Casework F Furniture and Furnishings G Physical Therapy and Gym Equipment K Food Service Equipment L Laboratory Equipment M Miscellaneous Medical Equipment P Plumbing Fixtures R Refrigeration Equipment S Sterilizers, Decontamination and Associated Equipment T Shop Equipment and Tools U User Defined Items (used in SEPS only) V Veterinary Equipment X X-Ray Equipment and Accessories

National Stock Number / Federal Stock Catalog (NSN). Are used to identify the Federal Supply Group (FSG), Federal Supply Class (FSC), NATO Country Code, and National Item Identification Number (NIIN) of an applicable item

Logistical Category (LOGCAT). The LOGCAT codes listed in Table 2-1 are used by the MHS to classify purchase and installation responsibility. The responsibility column is the typical short acronym or term used to identify responsibility of Government and/or its Agent, and Contractor relative to purchase and installation. The description column provides a detailed explanation of the LOGCAT code. Nominal assignment of LOGCATs are provided to JSNs in the MS1691, however, Services and their Agents should review and edit these to fit the project’s execution strategy. Please note that in the construct of this document, the words “purchase, procurement and/or furnished” are synonymous.

LOGCAT Responsibility Description

A CFCI Contractor Furnished Contractor Installed. Equipment is purchased and installed by the construction contractor.

B GFCI Government Furnished Contractor Installed. Equipment is purchased or provided by the Government and installed by the construction contractor.

C GFGI Government Furnished Government Installed. Equipment is provided by the Government and installed by the Government (equipment vendor or agent).

D Leased Other. Leased or rented equipment, arranged by the Government, or any similar type arrangement requiring special funding and/or condition. Justification and approvals may be required for use of this category.

R Reuse Reuse. These are existing equipment assets that will be transferred and reused.

There may be no purchase costs although relocation funding may be required.

SECTION 5: UTILITY REQUIREMENTS FOR MEDICAL / DENTAL / VETERINARY EQUIPMENT

5.1. LEGEND OF UTILITIES. The utility codes and descriptions are intended to describe the base utility requirements for a selected JSN. Designers and planners must ensure to verify all utility requirements at time of specific equipment selection.

Utility 1: Plumbing (Water and Drainage) Code Description A Hot and cold water B Cold water and drain C Hot water and drain D Cold and hot water and drain E Treated water and drain F Cold, hot and treated water and drain G Cold and treated water and drain H Hot and treated water and drain I Drain only J Cold water only

Utility 2: Electrical Code Description A 120 volt, conventional outlet B 120 volt, special outlet C 208/220 volt D 120 and 208/220 volt E 440 volt, 3 phase F Special electrical requirements (includes, but is not limited to emergency power, multiple power connections, etc.)

G 208/220 volt, 3 phase

Utility 3: Medical Gas (Provide operating pressures in accordance with NFPA 99) Code Description A Oxygen B Vacuum C Air, low pressure (30 PSIG) max D Air, high pressure (85 PSIG) max E Oxygen and vacuum F Oxygen and medical air (50 PSIG) G Oxygen, vacuum and medical air (50 PSIG) H Vacuum and HP air (85 PSIG) minimum J Medical air (50 PSIG) K Vacuum and LP air (30 PSIG) maximum

Utility 4: Miscellaneous Gas Code Description A Steam B Nitrogen gas C Nitrous oxide D Nitrogen and nitrous oxide gas E Carbon dioxide gas F Liquid carbon dioxide G Liquid nitrogen H Instrument Air

Utility 5: Non-Medical Gas Code Description A Natural gas B Liquid propane gas C Methane D Butane E Propane F Hydrogen gas G Reserved H Acetylene gas

Utility 6: Miscellaneous Code Description A Earth ground B Lead lined walls C Remote alarm ground D Empty conduit with pull cord E Vent to atmosphere F Special gas requirements G Liquid gas requirements H RF/Magnetic shielding J Wall/ceiling support required K Empty conduit/pullcord & wall/ceiling support required M Earth ground and wall/ceiling support required P Lead lined walls and wall/ceiling support required

CUT SHEET: A1067_01055.pdf

A

UTIL 6

UTIL 5

UTIL 4

UTIL 3

UTIL 2

NOMENCLATURE: Mirror, Float Glass, ADA Accessible

UTILITIES: UTIL 1

DESCRIPTION: A high quality 1/4" polished float glass mirror with a stainless steel frame. Frame holds mirror in a tilted position for accessibility and compliance with ADA requirements. Mirror has a galvanized steel back secured to frame with concealed screws with integral horizontal hanging brackets. Mirror shall be approximately 18" wide and 36" high. Other sizes are available.

JSN: A1067

MODEL:

MANUFACTURER: Bradley Corporation

740-1836-2

LOG CAT:

LOG CAT LEGEND

A = FURNISHED AND INSTALLED BY GENERAL CONTRACTOR.

C = FURNISHED AND INSTALLED BY IOT CONTRACTOR.

R = RELOCATED AND INSTALLED BY IOT CONTRACTOR.

NOTE: GENERAL CONTRACTOR NOT RESPONSIBLE FOR PROCUREMENT OR INSTALLATION OF LOG CAT C OR LOG CAT R EQUIPMENT.

GENERAL CONTRACTOR AND IOT CONTRACTOR TO COORDINATE SCHEDULES FOR INSTALLATION OF EQUIPMENT.

FY18 Misawa AB Hospital Renovation

FA8903-15-D-0004 TO: 18-F-0072 / 021-10

Basis of Design Equipment Data Sheet

Fixed Tilt Mirror

Washroom Accessories Document No. 8725

Orders composed of products indicated as BradEXdd ®XX will be available to ship in three days after receipt of order at the factory. There is no pricing penalty for this service from Bradley.

© 2012 Bradley P.O. Box 309, Menomonee Falls, WI 53052-0309

Phone: 800.BRADLEY (800.272.3539) Fax: 262.253.4161 bradleycorp.com

This information is subject to change without notice. 12/19/2012

Fix tilt mirror with welded corners:

Standard Model 740-1830 (18" x 30") BradEXdd ®XX

Standard Model 740-1836 (18" x 36") BradEXdd ®XX

Standard Model 740-2436 (24" x 36") BradEXdd ®XX

Model 740-XXXX (Specify width and height)

Product Materials FRAME: 20 gauge stainless steel, corners welded and ground smooth to satin finish. 20 gauge angle stiffeners welded to frame provide additional rigidity.

BACK: galvanized steel, secured to frame with concealed screws equipped with integral horizontal hanging brackets.

MIRROR: first quality ¼" float glass, thermosetting infrared-cured paint backing with Poly-Glaze protective finish. Manufactured in accordance with ASTM C 1036 and ASTM C 1503. The back of the mirror is protected by a wedge of extruded polystyrene, which is placed between the mirror and the galvanized steel.

WALL HANGER: 18 gauge cold-rolled steel, all welded construction to form rigid template.

Optional Features Features Suffix

¼" tempered glass mirror in lieu of polished float glass mirror* -2

Laminate glass -3

Highly polished No. 8 architectural finish, 20 gauge stainless steel in lieu of polished float glass mirror

-4

Bright annealed 20 gauge stainless steel in lieu of polished float glass mirror

-5

Plexiglas® -6

*Either the Length (L) or the Width (W) must be greater than 25".

An inherent characteristic of a manufacturing process for tempered glass is distortion which may vary from mirror to mirror.

Stainless steel mirrors will differ in optic quality from glass mirrors.

In larger sizes, stainless mirrors are subject to distortion and/or "oil canning" for which Bradley Corporation cannot accept responsibility.

Bradley mirrors are not field interchangeable from horizontal to vertical or vice versa.

Always specify width first.

Installation Verify all rough-in dimensions prior to installation. Secure concealed mounting bracket to wall with screws (not included) at holes provided. Provide in-wall backing at mounting screw locations. Position mirror over mounting bracket to engage hanger tabs. Slide mirror down and lock into position.

Guide Specification Fixed tilt mirror shall be framed with 20 gauge stainless steel with 20 gauge concealed stiffeners. Welded corners shall be polished to a uniform satin finish. Mirror shall be of first quality ¼" float glass guaranteed for 15 years against silver spoilage and protected by a shock-absorbing, waterproof foam filler with Poly-Glaze protective finish. Back of unit shall be galvanized steel secured to frame with concealed screws, equipped with integral horizontal hanging brackets and separate wall hanger for concealed mounting.

Fixed Tilt Framed Mirror shall be Bradley Model 740-______" W x______" H (specify width and height).

ADA Compliant Consult local and national accessibility codes for proper installation guidelines.

Conformity and compliance to local and national codes is the responsibility of the installer.

sdhillier Text Box A1067 sdhillier Polygon sdhillier Polygon sdhillier Text Box X sdhillier

X

Fixed Tilt Mirror

Washroom Accessories Document No. 8725

Orders composed of products indicated as BradEXdd ®XX will be available to ship in three days after receipt of order at the factory. There is no pricing penalty for this service from Bradley.

© 2012 Bradley P.O. Box 309, Menomonee Falls, WI 53052-0309

Phone: 800.BRADLEY (800.272.3539) Fax: 262.253.4161 bradleycorp.com

This information is subject to change without notice. 12/19/2012

6°

Dimensions

Dim. "A" to finished floor

Dim. "A" Key Surface:

For Dim. "A" Bottom of Unit

Mirror's bottom edge of the reflecting surface to finished floor

40" (1016mm) 39¼" (997mm)

37" (940mm) 36¼" (921mm)

34" (864mm) 33¼" (845mm)

Rough wall opening:

Surface Mount: No rough wall opening, see overall dimensions

BradEXdd ® XX Models Width

(Inches) W

Height (Inches)

H

Overall Dimension (Inches)

Overall Dimensions (Millimeters)

Standard Model

Number

18" 30" 18 x 30 457 x 762 740-1830

18" 36" 18 x 36 457 x 914 740-1836

24" 36" 24 x 36 610 x 914 740-2436

Model 740 series angle framed mirrors can be fabricated to a maximum size of 48"W x 48"H.

“H”

1" (25mm)

“W”

“H” Hanger

Outer edge of mirror

4" (102mm)

2¼" (57mm)

Mounting Screw

Locations

3¹⁄₈" (79mm)

3¹⁄₈" (79mm) sdhillier Polygon sdhillier

A1067

CUT SHEET: A1080_90694.pdf

UTIL 6

UTIL 5

UTIL 4

UTIL 3

UTIL 2

NOMENCLATURE: Mirror, Posture, Wall Mounted

UTILITIES: UTIL 1

DESCRIPTION: Wall mounted posture mirror. Consists of a 1/4" plate glass in a sturdy corrosion resistant frame with water proof back. For educational and therapy programs.

JSN: A1080

MODEL:

MANUFACTURER: Hausmann Industries, Incorporated

LOG CAT:

LOG CAT LEGEND

A = FURNISHED AND INSTALLED BY GENERAL CONTRACTOR.

C = FURNISHED AND INSTALLED BY IOT CONTRACTOR.

R = RELOCATED AND INSTALLED BY IOT CONTRACTOR.

NOTE: GENERAL CONTRACTOR NOT RESPONSIBLE FOR PROCUREMENT OR INSTALLATION OF LOG CAT C OR LOG CAT R EQUIPMENT.

GENERAL CONTRACTOR AND IOT CONTRACTOR TO COORDINATE SCHEDULES FOR INSTALLATION OF EQUIPMENT.

FY18 Misawa AB Hospital Renovation

FA8903-15-D-0004 TO: 18-F-0072 / 021-10

THERAPY AND REHAB EQUIPMENT

A. Model 1675 “Combo” Portable Mirror/Weight Rack

FEATURES:

• High quality, full view, distortion-free glass mirror with ANSI safety backing.

• Reverse side has almond coated pegboard panel for optional Hugger® weights.

• Includes (11) pegboard safety hooks.

• Oak laminate frame and base.

• Easy rolling 2” dia. swiveling casters.

MODEL HEIGHT WIDTH DEPTH

1675 70” 24” 18”

Model 1675-100 Accessorized Mirror/Weight Rack

MODEL CONSISTS OF:

1675-100 (1) 1675 Rack, (1) 5581 Set of (16) Hugger® Weights

C. Model

Front View Reverse view

A. Model 1675 Combination Unit

Weights must be ordered as accessories

B. Model

A. Model

A. Model 1670 Portable Triple Mirror

• (3) high quality, distortion-free, full view glass mirrors with ANSI safety backing.

• Oak laminate frame and finished back.

• Mounted on 2” diameter swiveling casters.

• Viewing angles are easily changed and locked in desired position. Each mirrored panel is 24” wide.

MODEL HEIGHT WIDTH DEPTH

1670 69” 60”(open) 24”(open)

B. Model 1671 Portable Single Mirror

• High quality, distortion-free glass mirror with

ANSI “shatter-stop” safety backing.

• Oak laminate frame and base.

• Finished oak laminate back.

• Mounted on easy rolling 2” diameter swiveling casters.

• Mirror height provides full body image.

MODEL HEIGHT WIDTH DEPTH

1671 70” 24” 18”

C. Model 1672 Wall Mounted Mirror

• High quality, full view, distortion-free glass mirror w/ANSI “shatter-stop”safety backing.

• Oak laminate frame.

• Equipped with mounting cleat for attachment to wall.

• Mirror frame measures 66” x 24”. Can be mounted 6” above floor so that overall height is 72”.

MODEL HEIGHT WIDTH DEPTH

1672 66” 24” 4” sdhillier Text Box A1080 sdhillier Polygon

CUT SHEET: A1130_AM409.pdf

UTIL 6

UTIL 5

UTIL 4

UTIL 3

UTIL 2

B

NOMENCLATURE: Cabinet, Control, Nitrogen

UTILITIES: UTIL 1

DESCRIPTION: Nitrogen control cabinet. Unit consists of supply cut-off valve, supply pressure gauge, pressure regulator (adjustable 0 to 200 PSI), outlet pressure gauge, nitrogen outlet and connection to surgical gas column. Specify recessed or surface mounting. Designed for powering surgical pneumatic tools.

JSN: A1130

MODEL:

MANUFACTURER: D.R.E., Inc.

Nitrogen Control Panel (#504)

LOG CAT:

LOG CAT LEGEND

A = FURNISHED AND INSTALLED BY GENERAL CONTRACTOR.

C = FURNISHED AND INSTALLED BY IOT CONTRACTOR.

R = RELOCATED AND INSTALLED BY IOT CONTRACTOR.

NOTE: GENERAL CONTRACTOR NOT RESPONSIBLE FOR PROCUREMENT OR INSTALLATION OF LOG CAT C OR LOG CAT R EQUIPMENT.

GENERAL CONTRACTOR AND IOT CONTRACTOR TO COORDINATE SCHEDULES FOR INSTALLATION OF EQUIPMENT.

FY18 Misawa AB Hospital Renovation

FA8903-15-D-0004 TO: 18-F-0072 / 021-10

Medical Gas - Nitrogen Control Panels

Add

1 For Quote

Listing Disclaimer

Product Description

Features

• Durable, easy to clean type 304 stainless steel front

• Self relieving 0-250 psi pressure regulator

• High flow capacity

• Patented Front Loaded (fast & easy to repair)

DISS 1120 Outlet

• Painted steel rough in box

• High quality ball valve

• Easy to read 2” 0-300 psi gauges

• Outlet supply tube facilitates piping to additional remote outlets

Specifications

All nitrogen control panels must be installed and tested in strict accordance with NFPA 99 standards and or other local codes before use.

Rough in box assembly is 14 Ga. Steel construction. Box is supplied with a plaster flange for easy mounting. Two ¼” nominal 3/8” OD Type K copper stubs are supplied to facilitate piping to the box and to any optional remote outlets. Box assembly is factory piped to allow for pipeline testing before nitrogen panel is installed.

http://www.dremed.com/listing_disclaimer.php sdhillier

A1130

The nitrogen panel includes a high flow selfrelieving pressure regulator capable of providing pressures up to 250 psi. A quarter turn brass, ball type valve shall be used to supply pressure to the regulator. Two 0-300 psi 2” diameter pressure gauges are provided to monitor both supply and outlet pressure. Panel also includes a front loaded CGA DISS 1120 nitrogen outlet.

The nitrogen panel is factory piped and 100% tested. All components are panel mounted on a type 304 stainless steel, silkscreened front panel.

NFPA – (National Fire Protection Association Pamphlet 99” Health Care Facilities”) compliant.

CGA – (Compressed Gas Association Pamphlet V-5 “Diameter Index Safety System”) compliant.

Options

• Available with ¼ female npt outlet connection

• Conversion kits available for Hill-Rom, Ohmeda, Medaes, Allied/Chemetron and

Oxequip nitrogen control panels.

A1130

CUT SHEET: A1165_6L711.pdf

UTIL 6

UTIL 5

UTIL 4

UTIL 3

UTIL 2

NOMENCLATURE: Track, IV, Ceiling Mounted, 7 Foot

UTILITIES: UTIL 1

DESCRIPTION: 7 ft. ceiling mounted IV track. Unit consists of a straight thick anodized aluminum track. It includes a carrier with self locking hinge, hook for attaching bottle hanger, and an adjustable pendant. Designed for dispensing IV solutions.

JSN: A1165

MODEL:

MANUFACTURER: Imperial Fastener Co., Inc.

IFC-1000, caps, IFC1007 w/3001

LOG CAT:

LOG CAT LEGEND

A = FURNISHED AND INSTALLED BY GENERAL CONTRACTOR.

C = FURNISHED AND INSTALLED BY IOT CONTRACTOR.

R = RELOCATED AND INSTALLED BY IOT CONTRACTOR.

NOTE: GENERAL CONTRACTOR NOT RESPONSIBLE FOR PROCUREMENT OR INSTALLATION OF LOG CAT C OR LOG CAT R EQUIPMENT.

GENERAL CONTRACTOR AND IOT CONTRACTOR TO COORDINATE SCHEDULES FOR INSTALLATION OF EQUIPMENT.

FY18 Misawa AB Hospital Renovation

FA8903-15-D-0004 TO: 18-F-0072 / 021-10

1400 SW 8th Street / Pompano Beach, Florida 33069 Tel: 954-782-7130 / Fax: 954-782-0089 / email: info@imperialfastener.com

HOME

ABOUT US

CUBICLE CURTAINS

CUBICLE TRACKS

IV SUPPORT SYSTEMS

BREAK-A-WAY CURTAINS

SHOWER CURTAINS

BLACKOUT CURTAINS

CART COVERS

EXPORT

CONTACT US

I.V. TRACKS & BOTTLE HOLDERS | INSTALLATION | I.V. SPECIFICATIONS

I.V. Tracks & Bottle Holders IFC-1000 I.V. Track

(w/ IFC-1007 carrier) IFC-1007 I.V. Carrier

Track size is 1 9/16” x 15/16” x .075 extruded 6063-T5 aluminum. Available in oval, “U”, or straight lengths. Also available in electrostatic white paint finish.

Locking roller carrier with four nylon wheels, stainless steel axle and 1/4" diameter stainless steel hanger loop.

IFC-1008 I.V. End Cap IFC-1009 I.V. Splice

Predrilled and fitted molded nylon. Supplied with mounting screws.

Fitted anodized aluminum sleeve. Available in white.

IFC-3000 Bottle Holder IFC-3001 I.V. Bottle Holder IFC-3008 I.V. Bottle Holder

Bright dipped anodized aluminum body with stainless steel ram horns and extender rod. One hand push button operation allows for up to 11 inches of adjustment. Used for ceiling heights up to 8'-6".

This model has the same features as our IFC-3000 but with an extended center shaft for ceilings over 8'-6".

Our 8-Bottle capacity unit has stainless steel ram horns and extender rod. One hand push botton operation allows for up to 18" of adjustment. Used for ceiling heights up to 9'-0".

Extended center shaft is available for higher ceilings.

sdhillier Text Box A1165 sdhillier Polygon sdhillier Polygon sdhillier Polygon

IFC-1004 Stationary I.V. Hook

Stationary body and ram horn is constructed of chrome plated steel and set in a cast aluminum ceiling bracket. Overall length is 6".

Copyright 2011 © Imperial Fastener Company, Inc.

Site Development by @ Artisian Designs

Home | About Us | Cubicle Curtains | Cubicle Tracks | IV Support Systems Break-A-Way | Shower Curtains | Blackout | Cart Covers | Export Privacy Policy | Terms of Use | Warranty | Sitemap | Contact Us sdhillier

A1165

CUT SHEET: A1195_32510.pdf

UTIL 6

UTIL 5

UTIL 4

UTIL 3

UTIL 2

NOMENCLATURE: Counter, Cleanup, With 2 or 3 Sinks

UTILITIES: UTIL 1

D

DESCRIPTION: Two or three sink cleanup counter. Unit is constructed of type 304 corrosion resistant stainless steel. It consists of three sinks 14"W X 16"H X 10"D, hot and cold water faucet, and pre-rinse spray hose. Equipped with channel reinforced drainboards, and backsplash, and supported by tubular stainless steel legs. Unit is designed for use in control sterile supply decontamination areas.

JSN: A1195

MODEL:

MANUFACTURER: Getinge USA, Inc.

6763 (Code 3904)

LOG CAT:

LOG CAT LEGEND

A = FURNISHED AND INSTALLED BY GENERAL CONTRACTOR.

C = FURNISHED AND INSTALLED BY IOT CONTRACTOR.

R = RELOCATED AND INSTALLED BY IOT CONTRACTOR.

NOTE: GENERAL CONTRACTOR NOT RESPONSIBLE FOR PROCUREMENT OR INSTALLATION OF LOG CAT C OR LOG CAT R EQUIPMENT.

GENERAL CONTRACTOR AND IOT CONTRACTOR TO COORDINATE SCHEDULES FOR INSTALLATION OF EQUIPMENT.

FY18 Misawa AB Hospital Renovation

FA8903-15-D-0004 TO: 18-F-0072 / 021-10

CUSTOMER:

REFERENCE:

6763 TRIPLE SINK MODULE

WORK STATIONS

PRODUCT SPECIFICATION

PRODUCT

Getinge clean-up sinks are specially designed for use with Getinge related equipment and accessories. Each is designed to perform specified tasks vital to the effective operation of any work area. Getinge clean-up sinks are an integral part of the total material handling & decontamination system, providing the necessary interface between personnel and equipment.

APPLICATION

The Triple Sink Module is designed to serve primarily as a pre-rinsing station for those items where gross soil has not been previously removed at point of use. It is ideally suited for soiled work areas in a processing system and/or clean sub-sterile areas within the OR. The countertop as well as the sink is de-signed to accommodate large instrument trays and containers.

QUALITY STATEMENT

Confidence in the Getinge Group is the most important quality criterion. This must be the hallmark of all our external and internal commitments, activities and products. Products and services supplied by Getinge must conform to the agreed terms and expectations to ensure recommendations for further busi-ness. The achievement of these quality goals is the basis for a continued competitive and successful enterprise.

CONSTRUCTION

All material for use in the fabrication of workstations shall be of the very best quality, selected for and adapted to the primary purpose for which it is intended.

The workstation shall be of welded construction and consist of a countertop with sink and fixtures, and understructure consist-ing of a shelf, apron and legs.

The countertop shall be constructed of 16 gauge, type 304 stainless steel with a satin finish. A 4'' (102 mm) high back-splash will be provided and top shall be reinforced with steel channels and covered with sound-deadening undercoating.

The front edge and sides of the countertop shall contain a raised 1/8'' (3 mm) drain bead for retaining water spillage.

The sink bowl shall be a formed, seamless type construction with internal corners rounded to a 1'' (25 mm) radius. Formed construction shall insure uniform side wall thickness. The bot-tom of the sink shall be pitched slightly to insure complete drain-ing. A strainer and tail piece will be provided with the sink. Sink shall be welded into the countertop and ground smooth, provid-ing a watertight joint. The sink shall be nominally sized 24'' (610 mm) L x 17'' (432 mm) W x 10'' (254 mm) D to handle major size instrument trays.

UNDERSTRUCTURE

All understructure (apron, legs and shelf) shall be constructed of 18 gauge stainless steel. The apron shall be approximately 11'' (171 mm) high and hide from view the undersurfaces of the countertop. The legs shall be tubular type 1-5/8'' (41.2 mm) O.D. diameter with stainless steel bullet type leg adjustment.

SINK FIXTURES

A T&S Brass Model 1152 deck-mounted, hot & cold water mixing faucet shall be provided and includes 8'' rigid swing nozzle and 4 -foot stainless steel hose w/spray valve. The assembly shall be capable of using water up to 180°F (82°C) at 30 psi (2.1 kg/cm2) minimum.

INSTALLATION AND ASSEMBLY

Sink Modules shall be shipped for easy assembly without the use of special tools. Standard and optional fixtures shall be shipped loose for assembly during installation. Others shall per-form assembling, setting in place, and connecting to building services.

MODELS

Freestanding – self supporting on legs

FINISH

All stainless steel

SIZE

25'' W x 36'' H (Adjustable) x 120'' (10 ft.) Long (635 x 914 x 3048 mm)

SINK PLACEMENT

Work Decks on Both Sides – Sinks Centered

Soiled Deck on Left – Sinks on Right Side

Soiled Deck on Right – Sinks on Left Side

OPTIONS

Compressed Air Gun

Treated Water Faucet

Tubing Manifold

Left Wall Side-Splash

Right Wall Side-Splash sdhillier Text Box A1195 sdhillier Text Box Provide with 1 hp garbage disposal K2620 sdhillier Text Box X sdhillier Text Box X sdhillier

THE GETINGE GROUP is a leading global provider of equipment and systems that contribute to quality enhancement and cost efficiency within healthcare and life sciences. Equipment, services and technologies are supplied under the brands ARJO for patient hygiene, patient handling and wound care, GETINGE for infection control and prevention within healthcare and life science and MAQUET for surgical workplaces, cardiopulmonary and critical care.

Getinge USA, Inc.

1777 East Henrietta Road Rochester, New York 14623-3133 U.S.A.

Phone: (800) 475-9040 Fax: (585) 272-5033 info@getingeusa.com www.getingeusa.com

D S

G et in ge is a re gi st er ed tr ad em ar k.

P rin te d in

U .S

.A

G et in ge is c on st an tly re vi ew in g its p ro du ct s fo r i m pr ov em en ts . C on se qu en tly , t he a ct ua l p ro du ct m ay d iff er s lig ht ly fr om th e pr od uc t p ic tu re d an d de sc rib ed h er e.

sdhillier Text Box X sdhillier Text Box X sdhillier

A1195

CUT SHEET: A1195M.pdf

UTIL 6

UTIL 5

UTIL 4

UTIL 3

UTIL 2

NOMENCLATURE: : Counter, Cleanup, With 2 or 3 Sinks

UTILITIES: UTIL 1

D

DESCRIPTION: Two or three sink cleanup counter. Unit is constructed of type 304 corrosion resistant stainless steel. It consists of three sinks 14"W X 16"H X 10"D, hot and cold water faucet, and pre-rinse spray hose. Equipped with channel reinforced drainboards, and backsplash, and supported by tubular stainless steel legs. Unit is designed for use in control sterile supply decontamination areas.

JSN: A1195M

MODEL:

MANUFACTURER: Getinge USA, Inc.

6763 (Code 3904)

LOG CAT:

LOG CAT LEGEND

A = FURNISHED AND INSTALLED BY GENERAL CONTRACTOR.

C = FURNISHED AND INSTALLED BY IOT CONTRACTOR.

R = RELOCATED AND INSTALLED BY IOT CONTRACTOR.

NOTE: GENERAL CONTRACTOR NOT RESPONSIBLE FOR PROCUREMENT OR INSTALLATION OF LOG CAT C OR LOG CAT R EQUIPMENT.

GENERAL CONTRACTOR AND IOT CONTRACTOR TO COORDINATE SCHEDULES FOR INSTALLATION OF EQUIPMENT.

FY18 Misawa AB Hospital Renovation

FA8903-15-D-0004 TO: 18-F-0072 / 021-10

CUSTOMER:

REFERENCE:

6763 TRIPLE SINK MODULE

WORK STATIONS

PRODUCT SPECIFICATION

PRODUCT

Getinge clean-up sinks are specially designed for use with Getinge related equipment and accessories. Each is designed to perform specified tasks vital to the effective operation of any work area. Getinge clean-up sinks are an integral part of the total material handling & decontamination system, providing the necessary interface between personnel and equipment.

APPLICATION

The Triple Sink Module is designed to serve primarily as a pre-rinsing station for those items where gross soil has not been previously removed at point of use. It is ideally suited for soiled work areas in a processing system and/or clean sub-sterile areas within the OR. The countertop as well as the sink is de-signed to accommodate large instrument trays and containers.

QUALITY STATEMENT

Confidence in the Getinge Group is the most important quality criterion. This must be the hallmark of all our external and internal commitments, activities and products. Products and services supplied by Getinge must conform to the agreed terms and expectations to ensure recommendations for further busi-ness. The achievement of these quality goals is the basis for a continued competitive and successful enterprise.

CONSTRUCTION

All material for use in the fabrication of workstations shall be of the very best quality, selected for and adapted to the primary purpose for which it is intended.

The workstation shall be of welded construction and consist of a countertop with sink and fixtures, and understructure consist-ing of a shelf, apron and legs.

The countertop shall be constructed of 16 gauge, type 304 stainless steel with a satin finish. A 4'' (102 mm) high back-splash will be provided and top shall be reinforced with steel channels and covered with sound-deadening undercoating.

The front edge and sides of the countertop shall contain a raised 1/8'' (3 mm) drain bead for retaining water spillage.

The sink bowl shall be a formed, seamless type construction with internal corners rounded to a 1'' (25 mm) radius. Formed construction shall insure uniform side wall thickness. The bot-tom of the sink shall be pitched slightly to insure complete drain-ing. A strainer and tail piece will be provided with the sink. Sink shall be welded into the countertop and ground smooth, provid-ing a watertight joint. The sink shall be nominally sized 24'' (610 mm) L x 17'' (432 mm) W x 10'' (254 mm) D to handle major size instrument trays.

UNDERSTRUCTURE

All understructure (apron, legs and shelf) shall be constructed of 18 gauge stainless steel. The apron shall be approximately 11'' (171 mm) high and hide from view the undersurfaces of the countertop. The legs shall be tubular type 1-5/8'' (41.2 mm) O.D. diameter with stainless steel bullet type leg adjustment.

SINK FIXTURES

A T&S Brass Model 1152 deck-mounted, hot & cold water mixing faucet shall be provided and includes 8'' rigid swing nozzle and 4 -foot stainless steel hose w/spray valve. The assembly shall be capable of using water up to 180°F (82°C) at 30 psi (2.1 kg/cm2) minimum.

INSTALLATION AND ASSEMBLY

Sink Modules shall be shipped for easy assembly without the use of special tools. Standard and optional fixtures shall be shipped loose for assembly during installation. Others shall per-form assembling, setting in place, and connecting to building services.

MODELS

Freestanding – self supporting on legs

FINISH

All stainless steel

SIZE

25'' W x 36'' H (Adjustable) x 120'' (10 ft.) Long (635 x 914 x 3048 mm)

SINK PLACEMENT

Work Decks on Both Sides – Sinks Centered

Soiled Deck on Left – Sinks on Right Side

Soiled Deck on Right – Sinks on Left Side

OPTIONS

Compressed Air Gun

Treated Water Faucet

Tubing Manifold

Left Wall Side-Splash

Right Wall Side-Splash sdhillier Text Box A1195M sdhillier Text Box Provide with 1 hp garbage disposal K2620 sdhillier Text Box X sdhillier Text Box X sdhillier

THE GETINGE GROUP is a leading global provider of equipment and systems that contribute to quality enhancement and cost efficiency within healthcare and life sciences. Equipment, services and technologies are supplied under the brands ARJO for patient hygiene, patient handling and wound care, GETINGE for infection control and prevention within healthcare and life science and MAQUET for surgical workplaces, cardiopulmonary and critical care.

Getinge USA, Inc.

1777 East Henrietta Road Rochester, New York 14623-3133 U.S.A.

Phone: (800) 475-9040 Fax: (585) 272-5033 info@getingeusa.com www.getingeusa.com

D S

G et in ge is a re gi st er ed tr ad em ar k.

P rin te d in

U .S

.A

G et in ge is c on st an tly re vi ew in g its p ro du ct s fo r i m pr ov em en ts . C on se qu en tly , t he a ct ua l p ro du ct m ay d iff er s lig ht ly fr om th e pr od uc t p ic tu re d an d de sc rib ed h er e.

sdhillier Text Box X sdhillier Text Box X sdhillier

A1195M

CUT SHEET: A4995_AM479.pdf

UTIL 6

UTIL 5

UTIL 4

UTIL 3

UTIL 2

NOMENCLATURE: Table, Diaper Changing, Wall Mounted

UTILITIES: UTIL 1

DESCRIPTION: Wall mounted diaper changing table for use in public restrooms. Unit is a fold down system that folds upward when not in use for minimal intrusion into the room. Changing surface is contoured and has safety belt to insure that an infant will not fall from the table. Table is designed to hold no less than 250 pounds static weight. Closed dimensions are approximately 21" H x 36" W x 5" D. Open dimensions vary according to style. One system's open dimensions are 15 " high, 32" wide and 19" deep.

JSN: A4995

MODEL:

MANUFACTURER: Baby Changing Stations

KB200-00

LOG CAT:

LOG CAT LEGEND

A = FURNISHED AND INSTALLED BY GENERAL CONTRACTOR.

C = FURNISHED AND INSTALLED BY IOT CONTRACTOR.

R = RELOCATED AND INSTALLED BY IOT CONTRACTOR.

NOTE: GENERAL CONTRACTOR NOT RESPONSIBLE FOR PROCUREMENT OR INSTALLATION OF LOG CAT C OR LOG CAT R EQUIPMENT.

GENERAL CONTRACTOR AND IOT CONTRACTOR TO COORDINATE SCHEDULES FOR INSTALLATION OF EQUIPMENT.

FY18 Misawa AB Hospital Renovation

FA8903-15-D-0004 TO: 18-F-0072 / 021-10

New KB200 Koala Horizontal Baby Changing Station -

Quantity in Basket: none Code: KB200

Shipping Weight: 34.00 lbs

Color:

White Granite Cream Grey Earth

Quantity: 1 Add To Basket

Replaces the KB100. New improved design. More strength. More Changing Space, Two Liner Dispensers. Surface Mounted - Baby Changing Station Horizontal. The Koala Kare baby changing station is made with the exclusive Microban® protection and enhanced operator materials that improves sanitation and is embedded in the FDA approved blow molded high-density polyethylene bed surface.

The Koala Kare KB200 baby changing station has reinforced steel-on-steel hinge mechanism and metal mounting chassis with mounting hardware included. The changing station comes with labeled usage instructions and safety messages in four languages. Optional Braille label available. The contoured changing surface area is 450 sq. in (11,430 sq. mm) and comes complete with nylon safety strap and two bag hooks. The locking dual cavity liner dispenser holds approximately 50 KB150-99 bed liners. This surface mounted, horizontal design baby changing station complies with ADA requirements when installed properly. The horizontal design allows for easy access.

Dimensions are 35"w x 4"d x 22"h. Depth open: 22.5 inches. Mounting Height: 44.25 inches. Surcharge and customs may be added for shipments outside of U.S.

** Pre-Paid Price

Don't forget to order these related items!

Code Name Price KB150-99 Sanitary Liners - Case of 500 (On Sale, Reg $79.00) $49.99 H2G-2GALLONS Hands2GO Instant Hand Sanitizer - "2" Gallon Special (On Sale! Reg Price $220 - 37% Disc) $149.95 KB134-PLLD Plastic Liner Dispenser (Reg Price $90.00) $69.00 LINERS Liner Starter Package $10.00 sdhillier Text Box A4995

KOALA KARE PRODUCTS

KB200 HORIZONTAL WALL MOUNTED

BABY CHANGING STATION

KB200-00 CREAM

KB200-01 GREY

KB200-05 WHITE GRANITE

KB200-11 EARTH

KB200 TECHNICAL DATA SHEET

sdhillier Polygon sdhillier

A4995

MATERIALS:

FDA approved injection-molded polypropylene with Microban® antimicrobial additive embedded into the bed surface. Reinforced steel-on-steel hinge mechanism and metal mounting chassis with mounting hardware included. Labelled usage instructions and safety messages in four languages. Optional Braille label available. Contoured changing surface area is 450 sq. in (11,430 sq. mm) and comes complete with nylon safety strap and bag hooks. Dual cavity liner dispenser holds approximately 50 KB150-99 bed liners.

OPERATION:

Concealed pneumatic cylinder and metal mounting chassis provides controlled, slow opening and closing of bed. Polypropylene is easy to clean and resists odors and bacterial growth. Complies with ASTM static load performance requirements when properly installed.

Warning: To ensure that the unit supports the intended loads, baby changing stations must be properly installed according to the manufacturer’s instructions.

SPECIFICATION:

Baby changing station body shall be durable, injection-molded polypropylene. Design of unit shall be surface-mounted. Unit shall be equipped with a pneumatic cylinder for controlled opening and closing of bed. Bed shall be secured to metal mounting chassis with a concealed steel-on-steel hinge. No hinge structure shall be exposed on interior or exterior surfaces. Unit shall have mounting hardware included. Unit shall have Microban® antimicrobial embedded into plastic material on the changing surface. Unit shall conform to ANSI S117.1 Accessible and Usable Building and Facilities, ASTM F 2285-04 Standard Safety Performance Specification for Diaper Changing Tables for Commercial Use, ANSI Z535.4 Product Safety Signs and Labels, EN 12221-1:2008, ASTM G22 Antibacterial standards or local code if more stringent installation requirements are applicable for Barrier-Free accessibility. Unit shall comply with ADA regulations when properly installed. Bed shall have smooth concave changing area with a nylon safety strap and two hooks for bags or purses.

Unit shall have a built-in Liner Dispenser for use with 3-ply chemical free biodegradable bed liners, instructional graphics and safety messages in 4 languages.

Optional Braille label is available. Unit shall be backed by manufacturer’s 5-year limited warranty on materials and workmanship and include a provision for replacement caused by vandalism. Unit shall be manufactured in the U.S.A.

INSTALLATION:

To ensure proper installation and compliance to building codes, it is recommended that a qualified person or carpenter perform the installation of the unit. The unit must be properly installed onto a permanent wall that is capable of supporting significant weight and can accommodate the supplied installation hardware. The Koala Baby Changing Station meets ADA regulations when properly installed.

Drilling holes and mounting the station:

1. Remove changing station from the shipping container and check for any freight damage.

If damage is found, please call Koala Kare Products’ Customer Service at 888.733.3456. Remove “Installation Kit” and “Operator Kit” from box. Please give “Operator Kit” to facility manager or operator. Box should contain two pieces: the bed and metal mounting chassis and the wall mount liner dispenser. Identify the best location for installing the unit.

2. Standard Installation- Remove the bed and chassis from the box and select the wall area where the unit will be installed. Make sure you have taken into consideration the operating clearance of 9½” (241.3 mm) on both sides of the exposed chassis and 22” (558.8 mm) from wall surface when open. Measure from the floor 44¼” (1123.95 mm) on stud center and mark the wall.

The mounting holes are designed for 16” stud centers. Ensure the locations you have marked for the mounting holes are level before drilling. Drill pilot holes for keyhole mounting using a 1/8” regular drill bit.

Masonry or Tile over Stud Wall- Use a 7/32” (5.56 mm) masonry drill bit for the pilot hole until you hit the stud. Change bit to 1/8” (3.18 mm) regular drill bit.

Metal Stud or Concrete Block- If the wall has wood studs that are not on 16” (406.4 mm) centers, has metal studs or an underlying surface of concrete block, drill with a ½” (12.7 mm) masonry bit. (You may have to purchase toggles before installing.) You must allow a minimum of inside wall space for toggles to turn depending on toggles used. Insert and tighten toggles.

3. Screw two of the mounting screws into the pilot holes leaving ¼” (6.35 mm) exposed to allow keyhole slots to be easily mounted over the screw heads. Place chassis over screws. After securing the unit using the keyhole slots, verify that the unit is level. Tighten top two screws so that they are flush with the wall. Use the four lower holes as a guide to mark and drill pilot holes. Use remaining four screws and four washers to complete installation of bed and mounting bracket.

Insert washers over lower four screws. All SIX screws and four washers must be mounted to the chassis.

4. Ensure liner dispenser is free from damage. Remove key, unlock, and open liner dispenser lid. This will expose liner dispenser mounting holes. Line up dispenser mounting holes onto chassis and secure with the four screws provided. Close and lock the liner dispenser door.

5.Clean work area and inspect unit to ensure it opens and closes smoothly. Give Operator Kit and key to the facility operator. Replacement parts and additional liners can be purchased from your local distributor or by calling Koala at 888.733.3456 or 303.539.8300.

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions without notice.

Koala Kare Products ǁ 6982 S Quentin St. ǁ Centennial, CO 80112 Toll Free: 888.733.3456 ǁ 303.539.8300 ǁ Fax: 303.539.8399 www.koalabear.com sdhillier

CUT SHEET: A5030_01055.pdf

UTIL 6

UTIL 5

UTIL 4

UTIL 3

UTIL 2

NOMENCLATURE: Bench, Stall, Shower, Built In

UTILITIES: UTIL 1

DESCRIPTION: Shower bench; built-in. Eighteen (18) gauge stainless steel frame with anchors built-in into the wall. Size and shape as required.

JSN: A5030

MODEL:

MANUFACTURER: Bradley Corporation

LOG CAT:

LOG CAT LEGEND

A = FURNISHED AND INSTALLED BY GENERAL CONTRACTOR.

C = FURNISHED AND INSTALLED BY IOT CONTRACTOR.

R = RELOCATED AND INSTALLED BY IOT CONTRACTOR.

NOTE: GENERAL CONTRACTOR NOT RESPONSIBLE FOR PROCUREMENT OR INSTALLATION OF LOG CAT C OR LOG CAT R EQUIPMENT.

GENERAL CONTRACTOR AND IOT CONTRACTOR TO COORDINATE SCHEDULES FOR INSTALLATION OF EQUIPMENT.

FY18 Misawa AB Hospital Renovation

FA8903-15-D-0004 TO: 18-F-0072 / 021-10

© 2011 Bradley Corporation P.O. Box 309, Menomonee Falls, WI 53052-0309

Phone: 800.BRADLEY (800.272.3539) Fax: 262.253.4161 bradleycorp.com

956, 9561 Antimicrobial L-shaped Shower Seat

Washroom Accessories Document No. 9010

Orders composed of products indicated as BradEX® will be available to ship in three days after receipt of order at the factory. There is no pricing penalty for this service from Bradley.

This information is subject to change without notice. 11-2-2011

Color – Speckled White

Antimicrobial Agent BradEX®

Product Materials FRAME: 1" dia. 18 gauge stainless steel tubing. Welded.

WALL BRACKET: 16 gauge stainless steel with stainless steel piano hinges.

RETAINING BRACKET: 16 gauge stainless steel. Positive bullet-type catch holds seat securely in up or down position.

SEAT: rotational-molded polyethylene. Provides maximum comfort and fl ex without compromising strength. Will not retain heat or cold. Antimicrobial agent molded into seat to inhibit the growth of bacteria that cause product degradation.

Operation Hinged seat folds up and out of the way when not in use. When properly installed, seat can support up to 250 lbs. – static load.

Installation Verify all rough-in dimensions prior to installation. Provide concealed backing or anchors as specifi ed by architect before fi nished wall is applied.

Secure seat support bracket to wall with mounting screws (not included) at holes provided. Locate mounting holes 161⁄6" above fi nished fl oor. Secure leg support bracket to wall at locations shown. Mounting kit available from Bradley. For more information, visit bradleycorp.com.

WARNING: Be sure to use reinforced backing behind wall where mounting screws or anchoring devices are installed to ensure adequate support for the shower seat. All anchoring devices (supplied by installer) must be appropriate for specifi c wall construction. Severe personal injury and/or property damage may result from improper mounting.

Guide Specifi cation Folding shower seat shall be fabricated of molded polyethylene con tain ing an an ti mi cro bi al agent homogeneously distributed throughout the plastic matrix.

Seat secured to 1" diameter, 18 gauge stainless steel tubing. Support leg locks into 16 gauge retaining bracket with bullet-type catch. Shower seat shall meet or exceed ADA guidelines.

Overall dimensions: 34½2"W x 22"D x 3¼" thick.

22" (559mm)

Mounting hole locations for support retaining bracket

11¾" (298mm)8½" (216mm)

195⁄8" (498mm)

Finished wall

2" (51mm) Stainless steel retaining bracket Finished fl oor

18" ref.

(457mm)

1" dia. stainless steel tubing frame

34½" (876mm)

7" (178mm)

13" (330mm)

161⁄16" (408mm)

125⁄8" (321mm)

Mounting hole locations for wall bracket

4" (102mm)

13½" (343mm)

(RIGHT HAND)

(LEFT HAND)

sdhillier Text Box A5030 sdhillier Polygon

CUT SHEET: A5080_01055.pdf

UTIL 6

UTIL 5

UTIL 4

UTIL 3

UTIL 2

NOMENCLATURE: Dispenser, Paper Towel, Sensor, Hands Free

UTILITIES: UTIL 1

DESCRIPTION: A surface mounted, sensor activated, automatic, roll paper towel dispenser. The unit dispenses a paper towel automatically only when hands are place in position below the dispenser for maximum sanitation and hygiene. May include adjustable settings for sheet length, time delay, and sensor range. Unit is battery operated or with optional AC power adapter.

JSN: A5080

MODEL:

MANUFACTURER: Bradley Corporation

2A02-11

LOG CAT:

LOG CAT LEGEND

A = FURNISHED AND INSTALLED BY GENERAL CONTRACTOR.

C = FURNISHED AND INSTALLED BY IOT CONTRACTOR.

R = RELOCATED AND INSTALLED BY IOT CONTRACTOR.

NOTE: GENERAL CONTRACTOR NOT RESPONSIBLE FOR PROCUREMENT OR INSTALLATION OF LOG CAT C OR LOG CAT R EQUIPMENT.

GENERAL CONTRACTOR AND IOT CONTRACTOR TO COORDINATE SCHEDULES FOR INSTALLATION OF EQUIPMENT.

FY18 Misawa AB Hospital Renovation

FA8903-15-D-0004 TO: 18-F-0072 / 021-10

This information is subject to change without notice.

Always consult local and national codes for proper installation guidelines.

Conformity and compliance to local and national codes is the responsibility of the installer. 7/31/2012

© 2012 Bradley P.O. Box 309, Menomonee Falls, WI 53052-0309

Phone: 800.BRADLEY (800.272.3539) Fax: 262.253.4161 bradleycorp.com

2A02 Sensor Activated Roll Paper Towel Dispenser

Washroom Accessories Document No. 9407

Model 2A02 — Recessed (recesses 9-3/4"; projects 2-3/4") Model 2A02-10 — Semi-Recessed (recesses 4"; projects 8-1/2") Model 2A02-11 — Surface-Mounted (projects 13-1/4") Diplomat Series

Roll Paper Towels

Product Materials CABINET: 0.030-inch/22ga.-(0.76 mm) stainless steel with exposed surfaces in architectural satin finish. Welded construction with seamless corners and burr-free edges.

FLANGE: 0.030-inch/22ga.-(0.76 mm) stainless steel with exposed surfaces in architectural satin finish. One-piece seamless construction, 1" wide with 1/4" return.

DOOR: 0.036-inch/20ga.-(0.92 mm) stainless steel with full length piano hinge and tumbler lock keyed like other Bradley units. Front of door has matching curvature to other Bradley Diplomat washroom accessories.

TOWEL DISPENSER: furnished (manufactured by others).

Capacity One standard core 8"W x 8" diameter standard roll paper towels.

Operation Towel dispenser delivers preset length of towel (10" per operation).

Installation Verify all rough-in dimensions prior to installation. Recessed unit requires rough wall opening 15-1/2"W x 29-1/8"H x 9-3/4"D. (Semi-recessed unit only 4"D). Secure to framing with mounting screws (not included) at holes provided. Shim at screw points as required.

ADA Compliant Consult local and national accessibility codes for proper installation guidelines.

Conformity and compliance to local and national codes is the responsibility of the installer.

For information on Warranties, Maintenance and BAA/ARRA Compliance, visit our web site at:

bradleycorp.com/products/accessories/.

Recessed Model Shown

Guide Specification Sensor-activated roll paper towel dispenser in [recessed] [semi-recessed] [surface-mounted] wall cabinet. Towel dispenser door face formed with contemporary contours, radii, and finish matching related accessories in manufacturer's designer series. Towel dispenser capacity one: 8- inch wide by 8-inch diameter standard paper towel roll with sensor-activated towel dispensing mechanism, with hinged service door with keyed tumbler lock.

Universal keying. Formed from stainless steel sheet with satin finish on exposed surfaces, fully welded, with seamless corners and burr-free edges:

cabinet and flange 0.030-inch / 22-ga. thick; door 0.036-inch /20-ga. thick.

Towel dispenser operates with four D-size alkaline batteries.

Overall dimensions: 17-1/8"W x 30-5/8"H x 13-1/4"D.

MasterFormat Title: Commercial Toilet Accessories MasterFormat Number: 10 28 13.13

OmniClass Title: Toilet and Bath Specialties OmniClass Code: 23.31.25.00

Service Parts Available AC Conversion Kit (#P15-459) sdhillier Text Box A5080 sdhillier Text Box X sdhillier

Always consult local and national codes for proper installation guidelines.

Conformity and compliance to local and national codes is the responsibility of the installer. 7/31/2012

© 2012 Bradley P.O. Box 309, Menomonee Falls, WI 53052-0309

Phone: 800.BRADLEY (800.272.3539) Fax: 262.253.4161 bradleycorp.com

2A02 Sensor Activated Roll Paper Towel Dispenser

Washroom Accessories Document No. 9407

23⁄4" (70 mm)

171⁄8" (435 mm)

193⁄16" (497 mm)

305⁄8" (778 mm)

Dimensions

93⁄4" (248 mm)

Dim. "A" to finished floor

Dim. "A" Key Surface:

For Dim. "A" Locate Top of Rough

Wall Opening Locate Bottom of

Rough Wall Opening

Paper towel top of opening to finished floor

48" (1219mm) 66¹/₄" (1683mm) 37¹/₈" (943mm)

45" (1143mm) 63¹/₄" (1607mm) 34¹/₈" (867mm)

42" (1067mm) 60¹/₄" (1530mm) 31¹/₈" (791mm)

40" (1016mm) 58¹/₄" (1480mm) 29¹/₈" (740mm) sdhillier

A5080

CUT SHEET: A5082_01055.pdf

UTIL 6

UTIL 5

UTIL 4

UTIL 3

UTIL 2

NOMENCLATURE: Dispenser, Paper Towel, Sensor, Hands Free

UTILITIES: UTIL 1

DESCRIPTION: A surface mounted, sensor activated, automatic, roll paper towel dispenser. The unit dispenses a paper towel automatically only when hands are place in position below the dispenser for maximum sanitation and hygiene. May include adjustable settings for sheet length, time delay, and sensor range. Unit is battery operated or with optional AC power adapter.

JSN: A5082

MODEL:

MANUFACTURER: Bradley Corporation

2A02-11

LOG CAT:

LOG CAT LEGEND

A = FURNISHED AND INSTALLED BY GENERAL CONTRACTOR.

C = FURNISHED AND INSTALLED BY IOT CONTRACTOR.

R = RELOCATED AND INSTALLED BY IOT CONTRACTOR.

NOTE: GENERAL CONTRACTOR NOT RESPONSIBLE FOR PROCUREMENT OR INSTALLATION OF LOG CAT C OR LOG CAT R EQUIPMENT.

GENERAL CONTRACTOR AND IOT CONTRACTOR TO COORDINATE SCHEDULES FOR INSTALLATION OF EQUIPMENT.

FY18 Misawa AB Hospital Renovation

FA8903-15-D-0004 TO: 18-F-0072 / 021-10

Always consult local and national codes for proper installation guidelines.

Conformity and compliance to local and national codes is the responsibility of the installer. 7/31/2012

© 2012 Bradley P.O. Box 309, Menomonee Falls, WI 53052-0309

Phone: 800.BRADLEY (800.272.3539) Fax: 262.253.4161 bradleycorp.com

2A02 Sensor Activated Roll Paper Towel Dispenser

Washroom Accessories Document No. 9407

Model 2A02 — Recessed (recesses 9-3/4"; projects 2-3/4") Model 2A02-10 — Semi-Recessed (recesses 4"; projects 8-1/2") Model 2A02-11 — Surface-Mounted (projects 13-1/4") Diplomat Series

Roll Paper Towels

Product Materials CABINET: 0.030-inch/22ga.-(0.76 mm) stainless steel with exposed surfaces in architectural satin finish.