47QMCA23R0011_AttachmentE2_PurchaseDescriptions_Japan_2026-06-11.pdf

PURCHASE DESCRIPTION

RIGHT HAND DRIVE VEHICLES

FOR JAPAN

FY2027

11 JUNE 2026

1. SCOPE AND CLASSIFICATION

1.1 SCOPE

This document covers commercially available, current model year or newer, right hand drive, vehicles.

Types include sedans, passenger vans, sport utility vehicles, trucks, and buses. The vehicles covered by this document are listed by Standard Item Number. The SIN description, minimums, options, and manufacturers' data can be viewed in the Federal Vehicle Standards.

Note: Applicable to GSA SINs with suffix “J”

1.2 PURPOSE

The purpose of this document is to achieve a practical degree of standardization within the Federal Government’s automotive fleet (for Japan) and to simplify the competitive procurement of vehicles. This requirement establishes various types and sizes of passenger vehicles and general equipment requirements.

1.3 COVERAGE

This requirement covers only those vehicles generally acquired competitively by the Federal Government and does not include all the varieties of the commodity indicated by the title.

1.4 CLASSIFICATION

The vehicle’s characteristics, components, equipment, and options shall be based upon the Original Equipment Manufacturer (OEM) makes and models offered.

1.5 STANDARD ITEMS AND OPTIONS

The standard item and the coded additional systems and equipment (options) shall comply with the minimum and detailed requirements specified. The options are additional components, systems, devices, markings, and services that are to be provided and installed. Other special equipment items may be further described in authoritative documents. A minimum requirement cited in this document or in the procurement document is a “Requirement” to be furnished under the contract.

1.6 VEHICLES SUBJECT TO STATUTORY PRICE LIMITATIONS

Commercial passenger vehicles, completely equipped for ordinary operation and identified by the item numbers listed in the table below, are subject to statutory price limitations pursuant to 31 U.S.C. § 1343.

The current statutory price limitations were established in the Consolidated Appropriations Act, 2023, Public Law 117-73, Division D, Title VII, Section 702 (December 29, 2022).

The limits set forth in Division C, Title VII, Section 702 of Public Law 117-73 do not apply to any vehicle that is a commercial item and which operates on emerging motor vehicle technology, including but not limited to electric, plug-in hybrid electric, and hydrogen fuel cell vehicles.

Item No. 8J + 9J 12J 20J 21J 22J 23J 24J

Class II

Subcom and

Compact

5 PAX

Sedan

Subcom pact

5 PAX

Station

Wagon

4 PAX

Wagon

7 PAX

Wagon

8 PAX

Wagon

10 PAX

Wagon

14 PAX

Wagon

Style Trunk/

HB

Station

Wagon

Van

Wagon

Van

Wagon

Van

Wagon

Van

Wagon

Van

Wagon

Engine, Cylinders

4 4 4 4 4 4 4

Transmission

Type

Manual Manual Manual Manual Manual Manual Manual

Brake Type Power

Assist

Power

Assist

Power

Assist

Power

Assist

Power

Assist

Power

Assist

Power

Assist

Steering Power

Assist

Power

Assist

Power

Assist

Power

Assist

Power

Assist

Power

Assist

Power

Assist

Front Seats Bucket Bucket Bucket Bucket Bucket Bucket Bucket

Front Impact

Air Bags

Require Require Require Require Require Require Require

Occupant

Restraint Sys

Required Required Require Require Require Require Require

Tires, Type Radial Radial Radial Radial Radial Radial Radial

2. APPLICABLE DOCUMENTS

2.1 APPLICABLE REFERENCES

When published references are stated they shall be of the issue in effect on the date of the solicitation for offers or request for proposals.

2.1.1 ORDER OF PRECEDENCE

In the event of a conflict between this document and an applicable reference, this document shall take precedence.

2.2 ABBREVIATIONS AND DEFINITIONS

The following are the abbreviations and their meanings, as they appear in this standard:

ABS ........................ Antilock Braking System ALT......................... Alternate/Alternative AMP........................ Ampere AUTO ..................... Automatic BAT ........................ Battery CCA........................ Cold Cranking Amps HD ..........................Heavy Duty HDA........................Heaviest Duty Available KW…………………..Kilo Watt MAN........................Manual MAX........................Maximum MFR........................Manufacturer(s) MIN.........................Minimum KPH........................ Kilometers Per Hour OEM ....................... Original Equipment Manufacturer(‘s) PASS......................Passengers WB..........................Wheel Base Dimension 4X4 ......................... Four Wheel Drive

3. REQUIREMENTS

3.1 DESIGN

These requirements apply to all OEM furnished complete vehicles. The vehicles shall comply with applicable Japanese Ministry of Environment (MOE) standards in effect at time of ordering. The vehicles shall be type approved to the applicable United Nations Economic Commission for Europe (UN ECE) standards in effect at the time of ordering, unless specified otherwise. The vehicles shall be type approved to the applicable Japanese Ministry of Land, Infrastructure, Transport, and Tourism (MLIT), Road Transport Bureau, Road Transport and Motor Vehicle Safety Standards requirements in effect at the time of ordering, unless specified otherwise.

All Telecommunications Equipment, including Land Mobile Radios, Electronic Toll Collection Systems shall be type approved to the applicable Japanese Ministry of Internal Affairs and Communications (MIC), requirements in effect at the time of ordering, unless specified otherwise.

3.1.1 VEHICLES

The vehicles and the related equipment furnished under this document shall be the vehicle manufacturer’s current production. The vehicle(s) offered shall be as shown under the “Standard Item Number”. Vehicle(s) shall be complete with all the necessary operating components and accessories customarily furnished to the general public, whether stipulated herein or not, together with such modifications and accessories as may be necessary or are specified herein to enable the vehicle to function reliably and efficiently in sustained operation.

3.1.2 VEHICLE EQUIPMENT AND ACCESSORIES

The vehicle, components, assemblies, and accessories to be delivered under the contract shall be standard or optional commercial products that meet or exceed the requirements specified. They shall comply with local regulations for the regional destinations specified on the vehicle order on the date of manufacture. In addition, the vehicle(s) shall be furnished with the equipment, systems, and accessories as specified by the equipment codes. Equipment codes are defined within this document or are self-explanatory, as generally used in the automotive industry. All components and equipment shall be as represented in the manufacturer’s current model year technical data. The OEM component parts of the vehicle need not be the products of the same manufacturer. Optional and standard (GSA minimum requirements) equipment ordered shall be installed, serviced, and ready for use.

3.1.3 BASIC VEHICLE

The basic vehicles were established by statute and are subject to price limitations. Basic vehicles are identified in 1.6 and shall be equipped as specified in 1.6. Standard and optional equipment described in this standard do not apply to basic vehicles.

3.2 VEHICLE, COMPONENTS, AND SYSTEMS

3.2.1 CURB WEIGHT

The curb weight of the vehicle is defined as the weight of the complete vehicle without payload. Curb weight shall include the chassis, cab and body, all permanently attached devices, equipment, and a full complement of fuel, lubricants, and coolants.

3.2.2 PAYLOAD CAPACITY

The payload specified for each Item Number is defined as the minimum net weight for occupants and body/cargo carrying capacity, with the minimum equipment as specified. It does not include optional equipment that may be ordered. The ordering agency is responsible for loading the vehicle so that the front axle weight, rear axle weight and GVWR are not exceeded. The payload shall be evenly distributed in accordance with the vehicle design and intended use.

NOTE: PAYLOAD IS REDUCED BY THE WEIGHT OF EACH ADDED OPTION!!!

3.2.3 GROSS VEHICLE WEIGHT RATING (GVWR)

The gross vehicle weight rating is the maximum, fully loaded weight of a vehicle. The minimum GVWR of a vehicle furnished shall comply with payload shown for each Item Number, and shall be at least the sum of the curb weight and the payload capacity specified. Manufacturers shall provide a rating label showing the actual GVWR of the vehicle furnished. The chassis manufacturer’s maximum GVWR, shown on the certification label, shall not be increased.

3.2.4 EMISSION CONTROL SYSTEM.

Vehicles shall comply with emissions standards of the Japanese Ministry of Environment (MOE).

3.2.5 FUEL SYSTEM

The fuel tank(s) shall be protected by a metal shield when available from the OEM, or be located in an area which will be free from hazards of off-road operation. The fuel fill pipe shall be protected against deformation by body or component installation. A fuel gauge shall be provided which accurately indicates total remaining fuel.

3.2.6 COOLING SYSTEM

A coolant overflow recovery tank and compensating system shall be furnished. The cooling system shall be protected with an OEM solution of extended life antifreeze/coolant. The supplier shall provide the OEM maximum size cooling system for the engine provided.

3.2.7 BRAKE SYSTEM

All vehicles furnished shall be equipped with the OEM power assisted, self-adjusting, front and rear wheels, Antilock Braking System (ABS), unless specified otherwise.

3.2.8 STABILITY CONTROL SYSTEM

When code AVSC is specified, an automatic vehicle stability control system shall be furnished

3.3 DRIVETRAIN

3.3.1 ENGINE

The engine furnished shall have the minimum displacement as specified.

3.3.2 TRANSMISSION

3.3.2.1 CODE “T2” AUTOMATIC TRANSMISSION

The OEM standard production automatic transmission shall be provided, unless otherwise specified.

3.3.2.1.1 AUTOMATIC TRANSMISSION FLUID COOLER

The OEM standard automatic transmission fluid cooler shall be provided.

3.3.2.2 MANUAL TRANSMISSION

When specified by code T5, a manual transmission shall be provided. The number in the code represents the number of forward transmission gears.

OR

When specified, the OEM manual transmission shall be provided. The minimum quantity of forward gears shall be as specified in the standard item number.

3.3.2.2.1 CLUTCH

Vehicles equipped with a manual transmission shall be furnished with the OEM heaviest duty available clutch assembly offered for the model furnished.

3.3.2.3 AUTOMATED MANUAL TRANSMISSION

When specified, an automated manual transmission shall be provided. The minimum quantity of forward gears shall be as specified in the standard item number

3.3.3 TRANSFER CASE

The transfer case shall be of the type that will provide a part-time (selective) four-wheel drive system.

When available from the OEM protective skid plates or shields shall be provided on all 4X4 vehicles and when specified (code SP).

3.3.4 DRIVE HUBS, FRONT WHEELS-FOUR WHEEL DRIVE (4X4) ONLY

The OEM heaviest duty available 4X4 full time or front wheel locking system engaged from the cab shall be furnished. Vehicles shall have automatic locking hubs.

3.4 SUSPENSION SYSTEM

3.4.1 SUSPENSION

The vehicle shall be equipped with a suspension system (axles, springs, wheels and tires) having a rated capacity equal to or in excess of the GVWR. All vehicles shall be furnished with OEM heaviest duty available springs, shock absorbers, and stabilizer device(s).

3.4.2 SPRING STOPS

The spring and/or axle stops furnished shall prevent the axle and other suspension components from striking any part of the chassis or body.

3.4.3 WHEELS, TIRES, and TIRE TREADS

The wheel and tire size shall be provided as specified by each OEM. Wheels and tires shall be of the identical size, type, brand, and load ranges per axle. All tires shall have radial construction.

3.4.4 SPARE TIRE, JACK, and TOOLS

When available from the OEM as standard equipment or as an OEM option, a full size spare assembly (a tire mounted on a wheel) shall be furnished as a part of the basic (minimum) vehicle. The full size spare tire shall be of the identical load range and rolling design characteristics as the tires furnished on the steering axle. In some cases the full size spare tire may not match identically in tread pattern or tire dimensions. If a full size spare assembly is not offered by the OEM, a space saver type spare assembly shall be furnished if offered by the OEM as standard or an option.

When spare tire assemblies are mounted inside of passenger vans and sport utility vehicles, a cover shall be furnished for the spare tire.

NOTE: Spare tire assemblies for vehicles with tire pressure monitoring systems may not have monitoring devices if the OEM does not offer them.

OEM jack and tire changing tools shall be provided.

3.5 ELECTRICAL

3.5.1 ALTERNATOR AND BATTERY

When additional electrical power consuming equipment is furnished, the chassis manufacturer shall provide a generating system capable of supplying the total continuous electrical load at normal engine idle for the equipment furnished with the completed vehicle. Batteries furnished shall be of the maintenance-free type.

3.6 CAB/BODY, EQUIPMENT AND ACCESSORIES

Controls and operating mechanisms shall be located for left-hand drive. Equipment controls shall be complete and conveniently located for the driver. Lever controls for specified equipment shall be designed and located to permit easy entrance and of the driver’s compartment. Instruments and controls shall be identified as to their function and installed in a manner to facilitate removal and servicing

3.6.1 STANDARD EQUIPMENT AND ACCESSORIES

Except as identified in vehicles subject to statutory price limitations, each vehicle shall be equipped with, but not limited to, the following OEM accessories: driver and passenger front air bags (unless specified otherwise); air conditioning (unless specified otherwise); power windows and locks; cruise control, tilt steering; interior lighting (dome); dual sun visors; dual outside mirrors; non-glare day and night type inside mirror; multi-speed, intermittent dual electric windshield wipers and washers; rear window defroster; finished steel wheels with center hubcaps, or full size wheel covers, or cast aluminum wheels;

headliner; floor carpet including carpeted mats for front and rear seating areas; trunk floor covering (carpet/mat); all tinted glass windows when available; electric power outlet;, keyed driver's door lock, and two sets of keys/fobs. Provisions for mounting front and rear license plates shall be provided. License plate brackets shall be furnished when available from the OEM. 41 CFR 102-34 requires the display of official U.S. Government license plates on the front and rear of all Government motor vehicles unless otherwise exempt, regardless of state motor vehicle requirements.

3.6.2 CONTROLS AND OPERATING MECHANISMS

Controls and operating mechanisms shall be located for right-hand drive. Equipment controls shall be complete and conveniently located for the driver. Lever controls for specified equipment shall be designed and located to permit easy entrance and of the driver’s compartment. Instruments and controls shall be identified as to their function and installed in a manner to facilitate removal and servicing.

3.6.3 PAINT, FINISH, OR COLOR

The government agencies’ vehicle(s) exterior will be selected from the manufacturer’s standard colors offered . The interior finish shall be manufacturer’s standard compatible color with the exterior.

3.6.4 MIRRORS, OUTSIDE

Dual OEM outside rearview mirrors shall be provided, one on each side of the vehicle.

3.7 VEHICLE EQUIPMENT CODES

The content of the following equipment codes are described in detail as required. Equipment codes may be specified as GSA minimum requirements for the standard item number or may be specified as GSA orderable options for the standard item number. All equipment codes do not apply to all standard items numbers.

3.7.1 CODE “AC2” AIR CONDITIONING

When code AC2 is specified, an OEM auxiliary rear air conditioning system shall be furnished.

3.7.2 CODE “AT”

When coder AT is specified, All-Terrain (AT) tread tires shall be provided and mounted. All-Terrain is suitable for both on-road and off-road use. The All-Terrain (AT) tread is intended to perform well under a variety of conditions found off-road while still providing acceptable on-road performance. This tread pattern is more aggressive and may improve traction off-road, but will result in shorter tire life, decreased ride comfort and increased tire noise on-road. The All-Terrain (AT) tread is offered as an option on SINs 4x4 and AWD.

Tread Types When code AT is specified, the corresponding tire tread, of the minimum size specified shall be provided.

Code AT - All Terrain tread

3.7.3 CODE “ATC” AUTOMATIC TRACTION CONTROL

When ATC is specified, an OEM automatic traction control system, functioning through the vehicle brake and/or engine systems, shall be furnished.

3.7.4 CODE “AVSC” AUTOMATIC VEHICLE STABILITY CONTROL

When code AVSC Is specified, the OEM’s integrated vehicle stability enhancement system shall be furnished. AVSC will help the driver control the vehicle on a variety of road surfaces, in inclement weather, and in avoidance maneuvers.

3.7.5 CODE “BL” BED LINER

When code BL is specified, an OEM protective cargo bed liner shall be furnished.

3.7.6 CODE “BTBE” TARPAULIN AND FRAME

When code BTBE is specified, a tarpaulin and frame shall be provided.

3.7.7 CODE “BUA” BACK-UP ALARM

When code BUA is specified, a back-up alarm shall be provided.

3.7.8 CODE “BCW” COLD WEATHER PACKAGE

When code BCW is specified, the following shall be provided as available from the OEM:

Heavier duty battery Heavier duty starter motor Low temperature coolant mixture Low temperature window washer fluid mixture Winter wiper blades

3.7.9 CODE “CBE” CARGO BED EXTENDER

When code CBE is specified, the OEM cargo bed extender shall be provided.

3.7.10 CODE “CM” CARPETED FLOOR COVERING

When code CM is specified, carpeted floor covering and carpeted floor mats shall be provided in all seating areas at a minimum.

3.7.11 CODES CNS CONSIGNEE DELIVERY LOCATIONS

When consignee (direct) delivery codes CNS, is specified, the contractor shall deliver the vehicle to the consignee delivery address designated on the motor vehicle delivery order.

The consignee is responsible for:

1. The predelivery inspection and servicing normally provided by the dealer during the standard dealer delivery process.

2. Notifying the contractor of the delayed delivery date and the in-transit mileage accumulation if applicable.

3. In the presence of the delivering driver, immediately inspecting the vehicle for damage, abuse, loss or theft that may have occurred during transit. Any such findings should be accurately described on the delivery receipt the driver presents for signature. If the vehicle(s) are covered with snow, Ice or dirt so as to prevent a complete inspection at the time of delivery, this is to be noted on the delivery receipt. The driver is required to acknowledge any notification on the delivery receipt by signature.

4. Notifying the contractor of any damages or shortages found within 24 hours.

Items normally installed by the dealer as part of the predelivery servicing shall be shipped in the vehicle.

The consignor is responsible for:

The fuel tank(s) shall be filled with a minimum of 10 liters of fuel.

The vehicle(s) must be delivered-accepted wheels on ground.

Camp Zama

Region

1 - Okinawa

2 – Kyushu

3 – Honshu South

4 – Honshu Central

5 – Honshu North

6 - Hokkaido

3.7.11.1 CODE “CNS1”

When code CNS1 is specified, the vehicle shall be delivered to Zone 1- Okinawa as depicted on the map, installations include:

Navy (USN)-Kadena Air Force (USAF)-Kadena Marine Corps (USMC)-Futenma Marine Corps (USMC)-Camp Butler Army (USA)-Okinawa Army (USA)-Okinawa- Torri Station Defense Health Agency (DHA)-Okinawa Defense Logistics Agency (DLA)-Camp Kiner General Services Administration (GSA)-Kadena

3.7.11.2 CODE “CNS2”

When code CNS2 is specified, the vehicle shall be delivered to Zone 2- Kyushu as depicted on the map, installations include:

USN-Sasebo DLA-Sasebo

3.7.11.3 CODE “CNS3”

When code CNS3 is specified, the vehicle shall be delivered to Zone 3- Honshu South as depicted on the map, installations include:

USMC-Iwakuni USA-Hiroshima USA-Kure DLA-Iwakuni

3.7.11.4 CODE “CNS4”

When code CNS4 is specified, the vehicle shall be delivered to Zone 4- Honshu Central as depicted on the map, installations include:

USN-Yokosuka USN- Atsugi USAF- Yokota USA- Camp Zama USA- Sagami DLA- Yokosuka

3.7.11.5 CODE “CNS5”

When code CNS5 is specified, the vehicle shall be delivered to Zone 5- Honshu North as depicted on the map, installations include:

USN-Misawa USAF- Misawa DLA-Misawa GSA- Misawa

3.7.11.6 CODE “CNS6”

When code CNS6 is specified, the vehicle shall be delivered to Zone 6- Hokkaido as depicted on the map, installations include:

3.7.11.1 CODE “CNS1”

When code CNS1 is specified, the vehicle shall be delivered to the following location:

YOKOSUKA US Navy

NAVFAC FAR EAST PWD YOKOSUKA

TRANSPORTATION

BLDG 1851

1 TOMARICHO,

YOKOSUKA-SHI, KANAGAWA 238-0041

AP - Pacific, 238-0041

3.7.11.2 CODE “CNS2”

When code CNS2 is specified, the vehicle shall be delivered to the following location:

ATSUGI US Navy

NAVFAC FAR EAST PWD ATSUGI

PRODUCTION DIVISION, TRANSPORTATION

BRANCH (PRA33)

BLDG 243

ATSUGI KOUKU-KICHI,

AYASE-SHI, KANAGAWA 252-1101

AP - Pacific, 252-1101

3.7.11.3 CODE “CNS3”

When code CNS3 is specified, the vehicle shall be delivered to the following location:

YOKOTA GSA MART #46

GSA MART #46-ASIA

BLDG 924, YOKOTA AIR BASE

FUSSA-SHI, TOKYO 197-0001

AP - Pacific, 197-0001

3.7.11.4 CODE “CNS4”

When code CNS4 is specified, the vehicle shall be delivered to the following location:

YOKOTA USFJ

Pacific & Far East Branch

374 LRS GROUND

TRANSPORTATION

BLDG 4125

YOKOTA AIR BASE,

FUSSA-SHI, TOKYO 197-0001

AP - Pacific, 197-0001

3.7.11.5 CODE “CNS5”

When code CNS5 is specified, the vehicle shall be delivered to the following location:

MISAWA GSA MART #43

GSA Mart #43 Bldg 1334, Misawa AB; Hirahata 64

MISAWA-SHI, AOMORI 033-0032

AP - Pacific, 033-0032

3.7.11.6 CODE “CNS6”

When code CNS6 is specified, the vehicle shall be delivered to the following location:

MISAWA US Navy

NAVFAC FAR EAST PWD MISAWA

PRODUCTION DIVISION, TRANSPORTATION

BRANCH (PRM33)

BLDG 1395

MISAWA BEIGUN-KICHI,

MISAWA-SHI, AOMORI 033-0012

AP - Pacific, 033-0012

3.7.11.7 CODE “CNS7”

When code CNS7 is specified, the vehicle shall be delivered to the following location:

SASEBO US Navy

NAVFAC FAR EAST PWD SASEBO

TRANSPORTATION (PRS33)

BLDG 203

MUBANCHI, HIRASE-CHO,

SASEBO-SHI, NAGASAKI 857-0056

AP - Pacific, 857-0056

3.7.11.8 CODE “CNS8”

When code CNS8 is specified, the vehicle shall be delivered to the following location:

OKINAWA GSA PACIFIC AND FAR EAST BRANCH

Pacific & Far East Branch-Okinawa Bldg 792, 1st floor

KADENA-CHO, OKINAWA 904-0200

AP - Pacific, 904-0200

3.7.11.9 CODE “CNS9”

When code CNS9 is specified, the vehicle shall be delivered to the following location:

OKINAWA US Navy

NAVFAC FAR EAST PWD OKINAWA

BLDG 3571, KADENA AIR BASE,

KADENA-CHO, OKINAWA 904-0200

AP - Pacific, 904-0200

3.7.11.10 CODE “CNSZ”

When code CNSZ is specified, the vehicle shall be delivered to the following location:

DLA Distribution Yokosuka

BLDG 4831, 2ND Floor

Yokosuka Japan 96349 Phone : 011-81-46-816-6980

DSN: 315-243-6980

3.7.11.11 CODE “CNSY”

When code CNSY is specified, the vehicle shall be delivered to the following location:

DLA Disposition Services Iwakuni

BLDG 299 Marine Corps Air Station Iwakuni 1-Chrome Misumi-Cho Iwakuni-Shi Yamaguchi-Ken Japan 740-0025

Phone: 011-81-82-729-4008

DSN: 315-234-0611

3.7.11.12 CODE “CNSX”

When code CNSX is specified, the vehicle shall be delivered to the following location:

DLA Distribution Okinawa

BLDG 502 Camp Kinser Marine Corps Base

Okinawa Japan 9012100 Phone: 080-5511-4457

DSN: 315-234-0836

3.7.12 CODE “CNSW”

When code CNSW is specified, the vehicle shall be delivered to the following location:

Marine Corp Base Butler-Okinawa

Motor Transport Branch MCB Butler G4/MTB Unit 35001 BLDG. 5832 Camp Foster, Kitamae Okinawa 904-0117

POC: Joseph Vilailack Phone: 011-81-98-970-3657 EMAIL: joseph.vilailack@usmc.mil

MARK FOR ADDRESS:

Camp Foster, BLDG. 5822 Kitamae, Okinawa 904-0117

3.7.13 CODE “CNSV”

When code CNSV is specified, the vehicle shall be delivered to the following location:

Army Camp ZAWA (mainland Japan)

3.7.14 CODE “CNSU”

When code CNSU is specified, the vehicle shall be delivered to the following location:

Army Camp Kinser Okinawa-

3.7.15 CODE “CNST”

When code CNST is specified, the vehicle shall be delivered to the following location:

US Air Force Base- Kadena

Department of the Air Force

FB5270 18 LRS LGRDDC

BLDG 794 DOUGLAS BLVD

KADENA AIR BASE, 47 90402

Japan

Point of contact

FLEET MANAGER

18LRS.LGRVFMA.LGRVFMA@us.af.mil 81-989-381-111 ext. 7155

3.7.15.1 CODE “CNSS”

When code CNSS is specified, the vehicle shall be delivered to the following location:

US Air Force Base- Yokota

Point of contact

FLEET MANAGER

3.7.15.2 CODE “CNSR”

When code CNSR is specified, the vehicle shall be delivered to the following location:

US Air Force Base- Misawa

3.7.15.3 CODE “CNSQ”

When code CNSQ is specified, the vehicle shall be delivered to the following location:

US Air Force Base- Kunsan, ROK

3.7.15.4 CODE “CNSP”

When code CNSP is specified, the vehicle shall be delivered to the following location:

US Air Force Base- Osan, ROK

3.7.7 RESERVED

3.7.8 RESERVED

3.7.9 RESERVED

3.7.10 RESERVED

3.7.11 RESERVED

3.7.12 RESERVED

3.7.13 RESERVED

3.7.14 RESERVED

3.7.15 RESERVED

3.7.16 RESERVED

3.7.17 RESERVED

3.7.18 RESERVED

3.7.19 RESERVED

3.7.20 CODE “CRTS” CRUISE CONTROL and TILT STEERING

When code CRTS is specified, OEM cruise control and tilt steering shall be furnished.

3.7.21 CODE “CTB” OEM TRAILER BRAKE CONTROLLER

When code CTB is specified, the vehicle shall be furnished with an integrated electronic device that controls electrical power to trailer braking system and provides ideally matched braking force between tow vehicle and trailer.

3.7.22 CODE “CTBP” OEM TRAILER BRAKE CONTROLLER PRE-WIRING

When code CTBP is specified, the vehicle shall be furnished with a 4 way brake wiring connector or access to brake wiring located under the instrument panel. This connector or wiring access shall contain the following circuits:

• Battery Ground

• Battery Positive

• Stop Lamp Switch

• Electric Brake Feed

3.7.23 CODE “D3” SPECIAL TRACTION

When code D3 is specified, the vehicle shall be provided with a positive-traction, automatic locking differential.

3.7.24 CODE “D7” TOWING/MOUNTAIN RATIO

When code D7 is specified, it shall indicate that the vehicle will be used for trailering (towing), or operating in mountainous terrain. The vehicle shall be furnished with the OEM higher than standard numerical axle ratio that is compatible with the required equipment and options selected.

3.7.25 CODE “DTG” DARK TINTED GLASS

When code DTG is specified, OEM dark tinted glass on all windows behind the front seat shall be furnished.

3.7.26 CODE “EH” ENGINE BLOCK HEATER

Ordering Note: When Code “YD” is specified, “EH” shall be furnished.

When code EH is specified, OEM engine highest wattage block heater(s) shall be furnished.

3.7.27 CODE “EHM” ENGINE HOUR METER

When code “YD” is specified, an engine hour meter (EHM) shall be provided. The meter shall have a totalizing mechanism of not less than 9,999 hours for the chassis engine to register accurately the number of hours of operating time. The meter shall be of rugged construction to ensure continuous trouble-free performance under severe operating conditions. The meter shall be mounted on the cab instrument panel or in the engine compartment in a readable location.

3.7.28 CODE “FEX” SAFETY KIT AND FIRE EXTINGUISHER

When code FEX is specified, a safety kit and fire extinguisher shall be provided. The safety kit shall include reflective triangles and two (2) safety vests or EU approved warning lights. A type ABC fire extinguisher rated a minimum 2KG shall be provided.

3.7.29 CODE “FOG” FOG LIGHTS

When code FOG is specified, a fog lights shall be provided.

3.7.30 CODE “FTH” FRONT TOW HOOKS

When code FTH is specified, the chassis manufacturer’s front recovery hooks shall be frame mounted on the front of the vehicle. The chassis manufacturer’s front recovery hooks shall be provided on all 4X4 vehicles.

3.7.31 CODE “HB” HATCH BACK

When code HB is specified, a hatch back style body, in lieu of trunk, shall be provided.

3.7.32 CODE “HDAC” HEAVY DUTY AIR CONDITIONING

When code HDAC is specified, heavy duty air conditioning system with a minimum of 9kw capacity shall be provided.

3.7.33 CODE “HTG” HYDRAULIC LIFT TAILGATE

When code HTG is specified, a hydraulic lift tailgate rated at a minimum of 1000 kg shall be provided.

3.7.34 CODE “HTGU” HYDRAULIC LIFT TAILGATE

When code HTGU is specified, a fold under hydraulic lift tailgate rated at a minimum of 1000 kg shall be provided.

3.7.35 CODE “LRI ” OVERHEAD STORAGE RACKS

When code LRI is specified, interior overhead storage racks shall be provided.

3.7.36 CODE “MBG” FRONT BRUSH GUARD

When code MBG is specified, the vehicle shall be equipped with a radiator and headlamp brush guard.

3.7.37 CODE “MF” FLOOR MATS

When code MF is specified, carpeted floor mats shall be provided.

3.7.38 CODE “MIL” MILITARY MARKINGS AND DATA PLATES

When code MIL is specified and available under contract, the following shall be furnished:

1. Data Plate. A data plate only shall be furnished. No other exterior military markings shall be furnished.

At a minimum, the Data Plate shall be as follows:

2. A DD FORM 250 (MATERIAL INSPECTION AND RECEIVING

REPORT) shall be furnished in lieu of a GSA form 308.

3.7.40 CODE “NAV” NAVIGATION SYSTEM

When code NAV is specified, an OEM navigation system with Japan maps shall be provided. The navigation display and menu shall be selectable or configurable for both English and Japanese.

3.7.41 CODE “PSM and PSME” PARTS AND SERVICE MANUALS

When PSM or PSME is specified, the contractor shall furnish all parts lists and service publications for the vehicle and all equipment provided. When PSM is specified, the publications provided shall be printed documents. The publications shall be in English. The publications may be shipped separately from the vehicle to the consignee mailing address as shown on the Motor Vehicle Delivery Order. If the OEM does not support printed manuals, the offeror/contractor shall configure this GSA option as "Not Available" during the proposal phase.

When PSME is specified, the publications shall be provided in electronic media, or it may be web based.

All subscriptions beyond the 1st year shall be the ordering activity’s responsibility. If the OEM does not support electronic manuals, the offeror/contractor shall configure this GSA option as "Not Available" during the proposal phase.

3.7.42 CODE “PWL” POWER WINDOWS AND LOCKS

When code PWL is specified, OEM power windows and power locks option shall be provided.

3.7.43 CODE “RD” REAR ELECTRIC DEFROSTER

When code RD is specified, the OEM rear window electric defogger/defroster shall be furnished.

3.7.44 CODE “RKE” REMOTE KEYLESS ENTRY

When code RKE is specified, OEM optional remote keyless entry system shall be furnished.

3.7.45 CODE “RKS” REMOTE KEYLESS START

When code RKS is specified, the OEM optional remote keyless start system shall be furnished.

3.7.46 CODE “RUVM” REAR UNDER VIEW MIRROR

When code RUVM is specified, OEM rear mounted under view mirror shall be provided.

3.7.47 CODE “S3”THREE PASSENGER SEATING

When code S3 is specified, driver plus 2 passenger seating shall be furnished.

3.7.48 CODE “S5” FIVE PASSENGER SEATING

When code S5 is specified, driver plus 4 passenger seating shall be furnished.

3.7.49 CODE “S6” SIX PASSENGER SEATING

When code S6 is specified, driver plus 5 passenger seating shall be furnished.

3.7.50 CODE “S7” SEVEN PASSENGER SEATING

When code S7 is specified, driver plus 6 passenger seating shall be furnished.

3.3.51 CODE “SAR” AIR SPRING SUSPENSION REAR

When code SAR is specified, a rear air spring suspension shall be provided.

3.7.52 CODE “SK” METRIC ODOMETER

When code SK is specified, the odometer shall show cumulative distance in kilometers.

3.7.53 CODE “SP” SKID PLATES

When code SP is specified, protective plates, or shields, shall be provided. The OEM skid plate(s) shall provide protection for at least the transfer case. The skid plates shall be demountable for service of the components they protect. Sufficient openings shall be provided to enable draining of transmission and servicing the underside of the engine.

3.7.54 CODE “SPB” PERIMETER SEATING

When Code SPB is specified, perimeter seating shall be furnished.

3.7.55 CODE “SRG” SLIDING REAR WINDOW

When code SRG is specified, the OEM sliding rear glass window shall be furnished.

3.7.56 CODE “SRO” OEM REVERSE OBSTACLE SENSOR

When code SRO is specified, the vehicle shall be furnished with a sensor system that is installed on the bumper of the vehicle and detects the proximity of objects and transmits an audible signal to the driver. A switch may be provided that allows the driver to turn this device on/off.

3.7.57 CODE "TMA" TRANSMISSION MECHANICAL AUTOMATED

When code TMA is specified, an automated mechanical transmission shall be provided. The transmission may allow clutch-less shifting.

3.7.58 CODE “TSCF” TIRE-SPARE ASSEMBLY AND CARRIER-FRONT AXLE

When code TSCF is specified, an inflated spare wheel/tire assembly, identical to the front tires, furnished in a readily accessible carrier, located as to not protrude beyond the body and attached to the chassis, shall be provided. The tire must be positioned horizontal to the ground. The wheel shall be a steel disc regardless of optional wheel choices.

3.7.59 CODE “TSCR” TIRE-SPARE ASSEMBLY AND CARRIER--REAR AXLE

When code TSCR is specified, an inflated spare wheel/tire assembly, identical to the rear tires, furnished in a readily accessible carrier, located as to not protrude beyond the body and attached to the chassis, shall be provided. The tire must be positioned horizontal to the ground. The wheel shall be a steel disc regardless of optional wheel choices. When a wide single/floatation front tire is required by equipment selection, this option is not available.

3.7.60 CODE “TTPE” TRAILER TOW PACKAGE

When Code TTPE is specified, a trailer tow package, including coupler and wiring shall be provided. Two

(2) couplers and air lines for trailer brakes shall be provided. 24V 15-pin and 12V 13-pin electrical sockets shall be provided.

3.7.61 CODES “T5”,FIVE SPEED MANUAL TRANSMISSION

When code T5, is specified, a five speed manual transmission, respectively, shall be furnished.

3.3.62 CODE “VCB1” VIDEO CAMERA BACKUP

When code VCB1 is specified, video camera backup shall be provided

3.7.63 CODE “VU” VINYL INTERIOR

When Code VU is specified, OEM optional vinyl interior shall be furnished.

3.7.64 CODES “WARB” WARRANTY COVERAGE

When code WARB is specified, OEM standard commercial hybrid propulsion battery warranty shall be provided. This coverage shall be exclusive of accumulated drive away distance, whichever occurs first.

3.7.65 CODES “WARC” WARRANTY COVERAGE

When code WARC is specified, OEM standard commercial corrosion warranty shall be provided. This coverage shall be exclusive of accumulated drive away distance, whichever occurs first.

3.7.66 CODES “WARP” WARRANTY COVERAGE

When code WARP is specified, OEM standard commercial power-train warranty shall be provided. This coverage shall be exclusive of accumulated drive away distance, whichever occurs first.

3.7.67 CODES “WARR” WARRANTY COVERAGE

When code WARR is specified, OEM standard commercial whole vehicle (bumper-to-bumper) warranty shall be provided. This coverage shall be exclusive of accumulated drive away distance, whichever occurs first.

3.7.68 CODE “WR” INCREASED GVWR

When code WR Is specified, the GVWR shall be increased by the OEM to the maximum level available

3.7.69 CODE “YD” DIESEL ENGINE

When code YD is specified, OEM maximum power diesel engine available for the specified application shall be furnished.

3.7.70 CODE “ESSE” ENERGY STORAGE SYSTEM EXTENDED RANGE

When code ESSE is specified, an extended range energy storage system shall be provided.

3.7.71 CODES “ OBD” ON BOARD DIAGNOSTIC CONNECTOR

The OEM shall indicate the standard port type furnished on each individual standard item offered.

The OBD port shall be identified from the available choices listed below:

SAE J1962 Type A SAE J1962 Type B

SAE J1939

EOBD (Europe) JOBD (Japan) Other Industry Standard No OBD Port

3.7.72 CODE “AM6” AUTOMATED MANUAL TRANSMISSION 6 SPEED

When code AM6 is specified, an automated manual transmission with 6 forward speeds shall be provided.

3.7.73 CODE “GI” GROSS VEHICLE WEIGHT RATING INCREASE

When code GI is specified, an increased GVWR shall be provided.

3.7.74 CODE “GU” GROSS VEHICLE WEIGHT RATING DECREASE

When code GU is specified, a decreased GVWR shall be provided.

3.7.75 CODE “CBU” BACKUP CAMERA

When code CBU is specified, a backup camera shall be provided.

3.7.76 CODE “RPJ” RUSTPROOFING JAPAN

When code RPJ is specified, rustproofing suitable for mainland Japan shall be provided.

3.7.77 CODE “RPO” RUSTPROOFING OUTLYING ISLANDS JAPAN

When code RPO is specified, tropical rustproofing suitable for locations outlying islands and territories in Japan, shall be provided.

3.7.78 CODE “ALWJ” ALUMINUM WHEELS JAPAN

When code ALWJ is specified, aluminum wheels shall be provided.

3.7.79 CODE “MSEJ” STUDLESS WINTER TIRES

When code MSEJ is specified, stud less winter rated snow tires shall be provided and installed on the vehicle.

3.7.80 CODE “MER2” OUTSIDE MIRRORS

When code MER2 is specified, heated and powered outside mirrors shall be provided.

3.7.81 CODE “LU94" LE PATROL UPFIT JAPAN

This option is for Police-Security Forces use of a SUV (GSA SINs 9J, 103J, and 105J) or a Cargo Van (GSA SIN 30J). When code LU94 is specified, the following shall be provided.

The vehicle shall be equipped with a complete all LED emergency lighting system with siren and PA and other controllers, relays, harnesses, and up-fit items as required. All equipment shall be installed in full compliance with the manufacturer's guidelines and recommendations. The siren shall be equipped with a horn ringer sequencer feature, allowing the driver to scroll through wail, yelp, and phase tones by tapping the vehicles horn for "hands-free" control when the siren selector is in the standby position. The system shall be installed in accordance to the OEM’s Upfitter/Modifier Guide. The installation shall include the integration (cables, connections, and programming).

The mounting clip for the PA microphone shall be mounted higher than the leg, in the knee area, within center reach of driver and front passenger.

The emergency lighting and siren system shall include:

DESCRIPTION

One (1) light/siren controller, Whelen

CenCom Core, with OBD-II adapter, or equal, configured as required shall be provided

CenCom Core 399 Series

One (1) Whelen CenCom Core, or equal, control head

CCTL7

One (1) Whelen CenCom Core, or equal, installation kit shall be provided

C399K1

One (1) Whelen WeCan X Legacy, or equal, rooftop Lightbar - LED/RED/RED + Alley + TakeDown + Amber Traffic Arrow, 18 LED module

WeCan X Legacy

Whelen Lightbar bulkhead connector assemblies

Cable Assembly Lightbar End 46-078010-00

Cable Assembly Vehicle End 46-0787010-01

Two (2) Whelen, or equal, grill lights/LED/ Red

TLIR

Two (2) Whelen, or equal, behind glass on tailgate (operate in closed position) /LED/ Red

(operate in open position)

A suggested source of supply is:

Rita Company, Limited http://www.whelen-jpn.co.jp/

6 - 33 Aobaoka Minami Suita-Shi

Osaka 565

JP

(8166) 878-1254 www.whelen-jpn.co.jp/ https://www.whelen.com/find-a-distributor?f0=00000192-f88d-d033-af93-fdedc6af0000&f1=

The OEM center console shall be utilized. Two (2) power ports for 12-volt, a terminal block with two (2) 20 ampere spare circuits ignition controlled shall be provided.

An equipment tray shall be provided in the rear cargo area. One (1) mount assembly with an equipment tray for mounting provisions for a radio amplifier and siren controller shall be provided to allow access to the spare tire/wheel assembly (if equipped).

The contractor shall provide and install power, an ignition sense circuit, ground, antenna wiring, and mounting provisions for the base radios. All console and rear cargo cable ends shall include minimum length of a 24” service loop. All antennas shall be at least 18 inches from any other antenna or the light bar.

The customer shall provide and install, after acceptance and delivery, the radio, control head, microphone, and all other required cables. The customer shall configure and program the radios to prevent battery discharge when the vehicle is not in use. The customer’s make/models radios include:

Motorola / APX 7500

Motorola / APX 6500

Motorola / APX 3500

Motorola / XTL 5000

The contractor shall supply and install the following power cables) to the base radio, a dedicated protected circuit to the vehicle battery shall be provided

Motorola HKN6110B (100 Watt High Power)

The contractor shall provide and install three (3) single band antenna kits with tunable frequency range of 136MHz to 1 GHz

Sti-Co ROOF-FT-NITI 3

The contractor shall provide and install an auxiliary radio speaker, rated at 7 watts

Motorola B18-HSN4031 or

RSN4003A

or

HSN4042A

The contractor shall supply and install one (1) GPS antenna.

Motorola HAG4000 or

PM4000

tel:(8166)%20878-1254

One (1) gun vault shall be provided, Boss Strong Box model 7126-7530 top loader, or equal. All mounting brackets and hardware shall be provided. The vault dimensions are 14” width x 37” depth x 10” height.

The vault shall secure the M16 rifle with M68 or M150 optics, using the TACOM approved M16 collapsible butt stock conversion kit, the M4A1 rifle with M68 or M150 optics, and the M4 rifle with M68 or M150 optics.

The vault shall secure the weapons with a unique (not keyed alike) styled key-locking mechanism, which requires a unique specific key to open (or release) and secure. The weapon locker shall utilize keys and key control security measures as defined in Army Regulation 190-11. Combination or cypher locks are not acceptable. Five (5) sets of keys shall be provided.

Mike Curtis President Boss Safety Products

30081Comercio Rancho Santa Margarita, CA 92688

949-533-3510 mike@bosssafety.com

A prisoner transport system shall be provided and installed. The transport system shall include seating for a minimum of two occupants in the rear area. The seating shall include three-point seat belts.

The transport system shall include forward and rear partitions.

The partitions shall be fabricated of metal in the lower section and expanded metal with polycarbonate covers on the upper section.

The transport system shall include window and door guards.

All mounting shall be tool fastened. All sharp edges shall be deburred

A suggested source of supply locally in Japan is:

AKW

TEL 0774-44-2327

FAX 0774-43-4650

Exterior vinyl graphics shall be provided and installed in accordance to the current edition of the FEDSLEVES branding guide, option XW06 – Navy CNIC

3.7.82 CODE “LU95” WATCH COMMANDER JAPAN

This option is for Police-Security Forces use of a SUV (GSA SINs 9J, 103J, and 105J) or a Cargo Van (GSA SIN 30J). When code LU95 is specified, the following shall be provided.

The vehicle shall be equipped with a complete all LED emergency lighting system with siren and PA and other controllers, relays, harnesses, and up-fit items as required. All equipment shall be installed in full compliance with manufacturer's guidelines and recommendations. The siren shall be equipped with a horn ringer sequencer feature, allowing the driver to scroll through wail, yelp, and phase tones by tapping the vehicles horn for "hands-free" control when the siren selector is in the standby position. The system shall be installed in accordance to the OEM’s Upfitter/Modifier Guide. The installation shall include the integration (cables, connections, and programming).

The mounting clip for the PA microphone shall be mounted higher than the leg, in the knee area, within controller, Whelen

CenCom Core, with OBD-II adapter, or equal, configured as required shall be provided

CenCom Core 399 Series

One (1) Whelen CenCom Core, or equal, control head

CCTL7

One (1) Whelen CenCom Core, or equal, installation kit shall be provided

C399K1

One (1) Whelen WeCan X Legacy, or equal, rooftop Lightbar - LED/RED/RED + Alley + TakeDown + Amber Traffic Arrow, 18 LED module

WeCan X Legacy

Whelen Lightbar bulkhead connector assemblies

Cable Assembly Lightbar End 46-078010-00

Cable Assembly Vehicle End 46-0787010-01

Two (2) Whelen, or equal, (operate in closed position)

(operate in open position)

6 - 33 Aobaoka Minami Suita-Shi

Osaka 565

JP

The OEM center console shall be utilized. Two (2) power ports for 12-volt, a terminal block with two (2) 20 ampere spare circuits ignition controlled shall be provided.

An equipment tray shall be provided in the rear cargo area. One (1) mount assembly with an equipment tray for mounting provisions for a radio amplifier and siren controller shall be provided to allow access to the spare tire/wheel assembly (if equipped).

The contractor shall provide and install power, an ignition sense circuit, ground, antenna wiring, and mounting provisions for the base radios. All console and rear cargo cable ends shall include minimum length of a 24” service loop. All antennas shall be at least 18 inches from any other antenna or the light bar.

http://www.whelen-jpn.co.jp/ tel:(8166)%20878-1254

The customer shall provide and install, after acceptance and delivery, the radio, control head, microphone, and all other required cables. The customer shall configure and program the radios to prevent battery discharge when the vehicle is not in use. The customer’s make/models radios include:

Motorola / APX 7500

Motorola / APX 6500

Motorola / APX 3500

Motorola / XTL 5000

The contractor shall supply and install the following power cables) to the base radio, supplied by a 12V 30 Ampere circuit connected to the battery

Motorola HKN6110B (100 Watt High Power)

The contractor shall provide and install three (3) single band antenna kits with tunable frequency range of 136MHz to 1 GHz

Sti-Co ROOF-FT-NITI 3

The contractor shall provide and install an auxiliary radio speaker, rated at 7 watts

Motorola B18-HSN4031 or

RSN4003A

or

HSN4042A

The contractor shall supply and install one (1) GPS antenna.

Motorola HAG4000 or

One (1) gun vault shall be provided, Boss Strong Box model 7126-7530 top loader, or equal. All mounting brackets and hardware shall be provided. The vault dimensions are 14” width x 37” depth x 10” height.

The vault shall secure the M16 rifle with M68 or M150 optics, using the TACOM approved M16 collapsible butt stock conversion kit, the M4A1 rifle with M68 or M150 optics, and the M4 rifle with M68 or M150 optics.

The vault shall secure the weapons with a unique (not keyed alike) styled key-locking mechanism, which requires a unique specific key to open (or release) and secure. The weapon locker shall utilize keys and key control security measures as defined in Army Regulation 190-11. Combination or cypher locks are not acceptable. Five (5) sets of keys shall be provided.

A suggested source of supply is:

Mike Curtis

3.7.83 CODE “LU96” MWD JAPAN

This option is for Police-Security Forces use of a Cargo Van (GSA SIN 30J). When code LU96 is specified, the following shall be provided. The vehicle shall be equipped with heating and condition in the rear cargo area.

The vehicle shall be equipped with a complete all LED emergency lighting system with siren and PA and other controllers, relays, harnesses, and up-fit items as required. All equipment shall be installed in full compliance with manufacturer's guidelines and recommendations. The siren shall be equipped with a horn ringer sequencer feature, allowing the driver to scroll through wail, yelp, and phase tones by tapping the vehicles horn for "hands-free" control when the siren selector is in the standby position. The system shall be installed in accordance to the OEM’s Upfitter/Modifier Guide. The installation shall include the integration (cables, connections, and programming).

The mounting clip for the PA microphone shall be mounted higher than the leg, in the knee area, within controller, Whelen

CenCom Core, with OBD-II adapter, or equal, configured as required shall be provided

CenCom Core 399 Series

One (1) Whelen CenCom Core, or equal, control head

CCTL7

One (1) Whelen CenCom Core, or equal, installation kit shall be provided

C399K1

One (1) Whelen WeCan X Legacy, or equal, rooftop Lightbar - LED/RED/RED + Alley + TakeDown + Amber Traffic Arrow, 18 LED module

WeCan X Legacy

Whelen Lightbar bulkhead connector assemblies

Cable Assembly Lightbar End 46-078010-00

Cable Assembly Vehicle End 46-0787010-01

Two (2) Whelen, or equal, (operate in closed position)

(operate in open position)

6 - 33 Aobaoka Minami Suita-Shi

Osaka 565

JP

The OEM center console shall be utilized. Two (2) power ports for 12-volt, a terminal block with two (2) 20 ampere spare circuits ignition controlled shall be provided.

An equipment tray shall be provided in the rear cargo area. One (1) mount assembly with an equipment tray for mounting provisions for a radio amplifier and siren controller shall be provided to allow access to the spare tire/wheel assembly (if equipped).

The contractor shall provide and install power, an ignition sense circuit, ground, antenna wiring, and mounting provisions for the base radios. All console and rear cargo cable ends shall include minimum length of a 24” service loop. All antennas shall be at least 18 inches from any other antenna or the light bar.

http://www.whelen-jpn.co.jp/ tel:(8166)%20878-1254

The customer shall provide and install, after acceptance and delivery, the radio, control head, microphone, and all other required cables. The customer shall configure and program the radios to prevent battery discharge when the vehicle is not in use. The customer’s make/models radios include:

Motorola / APX 7500

Motorola / APX 6500

Motorola / APX 3500

Motorola / XTL 5000

The contractor shall supply and install the following power cables) to the base radio, supplied by a 12V 30 Ampere circuit connected to the battery

Motorola HKN6110B (100…