1240LT26Q0003-0001 Attachment 6B Kamas East Bunkhouse Asbestos Report .pdf

2410 WEST CALIFORNIA AVENUE ● SALT LAKE CITY, UTAH 84104

PHONE (801) 972-8400 ● FAX (801) 972-8459

Website: www.wasatch-environmental.com ● e-Mail: wei@wasatch-environmental.com

Mr. Jason Day, P.E., S.E. April 5, 2016 Civil Engineer Project No.: 1139-005 US Forest Service Uintah-Wasatch-Cache National Forests Supervisors Office 857 West South Jordan Parkway South Jordan, Utah 84095

SUBJECT: Asbestos Survey Report

Kamas Bunkhouse 45 East Center Street

Kamas, Utah

On February 19, 2016, Wasatch Environmental, Inc., (Wasatch) performed a limited asbestos survey at the above-referenced property. The purpose of this survey was to identify asbestos-containing materials (ACMs) in anticipation of possible renovation activities.

REGULATORY BACKGROUND

ACM is regulated by the Environmental Protection Agency (EPA) and the Occupational Safety & Health Administration (OSHA). In 1973, the EPA promulgated the "National Emission Standards for Hazardous Air Pollutants" (NESHAP) regulation, which addresses demolition and renovation activities. The federal NESHAP has been adopted by the Utah Department of Air Quality by reference in Section 214-1 of the Utah Air Conservation Rules.

The EPA uses the terms "friable" and “non-friable" to make a distinction between building materials that would readily release asbestos fibers when damaged or disturbed and those materials that are unlikely to result in significant fiber release.

Friable asbestos material is any material containing more than one percent (1%) asbestos that, when dry, can be crumbled, pulverized, or reduced to powder by hand pressure. If the asbestos content is less than 10% as determined by a method other than point counting by polarized light microscopy (PLM), asbestos content must be verified by point counting using PLM or may be assumed to contain greater than 1% asbestos content.

EPA defines two categories of non-friable materials: Category I non-friable ACM and Category II non-friable ACM:

Category I non-friable ACM is any asbestos-containing packing, gasket, resilient floor covering, mastic, or asphalt roofing product that contains more than 1% asbestos. Category I non-friable ACM must be inspected and tested before demolition if it is in poor condition.

EPA has determined that, if in poor condition, otherwise non-friable materials can release significant amounts of asbestos fibers and the material must be handled in accordance with NESHAP. Asbestos-containing packings, gaskets, resilient floor coverings, and asphalt roofing materials must be removed before demolition only if they are in poor condition and are friable. Additionally, when non-friable ACM is subjected to intense mechanical forces, such as those encountered during demolition or renovation, it can be crumbled, pulverized, or reduced to powder, and thereby release asbestos fibers. When non-friable materials are damaged or are likely to become damaged during such activities, they must be handled in accordance with the NESHAP regulation.

Wasatch Environmental Inc.

Category II non-friable ACM is any material excluding Category I non-friable ACM containing more than 1% asbestos.

"Regulated Asbestos-Containing Material" (RACM) is (a) friable asbestos material, (b) Category I non-friable ACM that has become friable, (c) Category I non-friable ACM that will be or has been subjected to sanding, grinding, cutting, or abrading, or (d) Category II non-friable ACM that has a high probability of becoming or has become crumbled, pulverized, or reduced to powder by the forces expected to act on the material in the course of demolition or renovation operations.

Asbestos NESHAP requires that each owner or operator of a demolition or renovation activity involving RACM remove all such material from a facility being demolished or renovated before any activity begins that would break up, dislodge, or similarly disturb the material or preclude access to the material for subsequent removal. ACM need not be removed before demolition if it:

Is a Category I non-friable ACM.

Is on a facility component that is encased in concrete or other similarly hard material and is adequately wet whenever exposed during demolition.

Was not accessible for testing and, therefore, was not discovered until after demolition began and, as a result of the demolition, cannot be safely removed. If not removed for safety reasons, the exposed RACM and any asbestos-contaminated debris must be treated as asbestos-containing waste material and kept adequately wet at all times until disposed.

Is a Category II non-friable ACM and the probability is low that the material will become crumbled, pulverized, or reduced to powder during demolition.

ASBESTOS SURVEY

Audra Heinzel of Wasatch performed the asbestos survey. Ms. Heinzel is a Utah-certified asbestos inspector (ASB-3952). This survey was conducted on behalf of the U.S. Forest Service, the property owner.

This survey was conducted for an approximately 1,620-square-foot, two-story residence with a basement constructed sometime prior to the early 1950s. The residence is constructed of metal siding over a wood frame with a pitched asphalt roof. Interior surfaces consist of wood, fiberboard, and wallboard walls;

fiberboard, wallboard, and acoustic tile ceilings; and wood, vinyl tile, and sheet-vinyl floors. The basement is unfinished and has a concrete floor. For the purpose of this survey, the roof was excluded from the survey.

For surfacing materials, a minimum of three samples is collected for homogenous suspect friable ACM encompassing less than 1,000 square feet, a minimum of five samples for materials encompassing between 1,000 and 5,000 square feet, and a minimum of seven samples for materials encompassing greater than 5,000 square feet. For miscellaneous materials such as floor and ceiling tiles, at least one sample is collected for each homogenous material.

Material visually determined to be non-asbestos (such as fiberglass, foam rubber, wood, etc.) was not sampled. Insulation located above ceilings was a mixture of blown-in cotton mixed with vermiculite;

therefore, in accordance with U.S. Forest Service procedures, the vermiculite has been assumed to contain asbestos and no sample was collected. Additionally, we did not sample the acoustic ceiling tile in the first floor office, kitchen, and bedroom #1 because it was in good condition and sampling the ceiling tile would compromise the ceilings’ integrity.

A total of 18 bulk material samples were collected from the following homogeneous materials:

One sample of carpet foam and mastic remnants on the wood floor in the first floor living room and hallway (approximately 225 square feet);

One sample of rock-pattern sheet vinyl flooring (approximately 223 square feet);

One sample of tan 9”x9” vinyl floor tile with gray streaks and associated mastic (approximately 180 square feet);

Five samples of fiberboard (approximately 2,256 square feet);

Five samples of wallboard (approximately 1,097 square feet);

One sample of gray sheet vinyl (approximately 30 square feet);

One sample of tan sparkle sheet vinyl flooring (approximately 327 square feet);

One sample of tan swirl 9”x9” vinyl floor tile (approximately 51 square feet);

One sample of black wall paper between the walls (approximately 3,000 square feet); and, One sample of TSI pipe wrap (approximately 8 linear feet).

Bulk samples were submitted under chain of custody to EMC Labs, a NVLAP-accredited laboratory. All samples were analyzed using visual estimation with the use of polarized light microscopy (PLM) according to EPA 600/R-93-116.

If the analytical results indicate that all the samples collected for each homogenous suspect ACM did not contain greater than 1% asbestos by weight (as defined by EPA), then the suspect ACM would be considered a non-ACM for the purposes of NESHAP. If the analytical results of at least one of the samples collected per homogenous suspect ACM indicate that asbestos is present in amounts greater than 1% asbestos by weight, all of the homogenous suspect ACM would be treated as ACM.

A summary of sampling locations and laboratory results is presented as Table 1. Sample locations are depicted on Figure 2. The laboratory results and associated chain-of-custody documentation are included in Appendix A. Asbestos content was identified in the following samples:

20% Chrysotile asbestos in the rock-pattern sheet vinyl and 7% chrysotile in the associated brown mastic (AS-2).

3% Chrysotile asbestos in the white skim coat in sample AS-7.

3% Chrysotile asbestos in the white skim coat in sample AS-15.

The skim coat in samples AS-7 and AS-15 were point counted to 3.6% Chrysotile asbestos and 3.2% Chrysotile asbestos, respectively.

There is potential for unidentified suspect ACM to be present within the building in areas that were not accessible during the inspection such as between walls and beneath floors.

Should you have any questions, please do not hesitate to contact us.

WASATCH ENVIRONMENTAL, INC.

Audra Heinzel Julie Kilgore, President Environmental Scientist Principal Environmental Manager

(ASB-3952)

Wasatch Environmental

(ASBC-169)

Distribution: (1) Addressee (electronic)

ATTACHMENTS:

Table 1 – Sampling Locations and Laboratory Results Figure 1 – First Floor Sample Location Map Figure 2 – Second Floor Sample Location Map Appendix A – Laboratory Reports Appendix B – Inspector Certification

The use or reuse of this information is restricted to the referenced document unless otherwise authorized.

Wasatch Environmental Copyright 2006

KAMAS BUNKHOUSE WEI 1139-005

N

S

EW

First Floor Asbestos Sample Location Map Figure 1

AS-2

AS-3

AS-1

AS-5

AS-4

AS-6

AS-8

AS-7AS-11

AS-12

AS-10

AS-9

AS-18

The use or reuse of this information is restricted to the referenced document unless otherwise authorized.

Wasatch Environmental Copyright 2006

N S

E W

Second Floor Asbestos Sample Location Map Figure 2Asbestos Sample Location

AS-16

AS-17AS-13

AS-15

AS-14

KAMAS BUNKHOUSE WEI 1139-005

TABLE 1

SAMPLING LOCATIONS AND LABORATORY RESULTS

Sample

Number Sample Location Material Description

Approximate

Quantity Result Condition Category

Black Carpet Foam

Yellow/Black GLue

Rock-pattern Tan

Sheet Vinyl 20% Chrysotile

Brown Mastic 7% Chrysotile

Tan 9"x9" Vinyl Floor

Tile with Gray

Streaks

Brown Backing, Yellow Mastic, Yellow/Black Mastic on Top

Brown Fiber Board

White Texture Skim

Coat

Brown Fiber Board

White Texture Skim

Coat

Brown Fiber Board

White Texture Skim

Coat

Brown Fiber Board non-detect

White Skim Coat 3% Chrysotile

Wallboard

White Texture

Gray Sheet Vinyl

Yellow Mastic

Tan Sparkle Sheet

Vinyl

Off-White Leveling

Compound

Good Non-Asbestos

AS-12 First Floor Central Hallway Floor 51 ft 2 non-detect Good Non-Asbestos

AS-11 First Floor Closet Floor 327 ft 2 non-detect

Tan Swirl 9"x9" Vinyl

Floor Tile

AS-10 First Floor Bathroom Floor 30 ft 2 non-detect Good Non-Asbestos

AS-9 Bedroom #1 Closet South Wall 1097 ft 2 non-detect

Non-Asbestos

Non-Asbestos

2,256 ft 2 Good

AS-1

223 ft 2 Good Category II (RACM)First Floor Kitchen South Floor non-detect

AS-2

Non-Asbestos

225 ft 2 Good Non-AsbestosFirst Floor Living Room Floor non-detect First Floor Kitchen South Floor Under Rock-

Pattern Sheet Vinyl AS-3 180 ft

2 Good

First Floor Living Room East CeilingAS-4

AS-5 First Floor Living Room East Ceiling Good2,256 ft non-detect non-detect non-detect

2,256 ft 2 Good

Non-AsbestosFirst Floor Living Room East CeilingAS-6

Good Texture is friable RACM

AS-8 Bedroom #2 West Wall 1097 ft 2 non-detect Good Non-Asbestos

AS-7 First Floor Closet East Wall 2,256 ft

Wallboard

Good Non-Asbestos

TABLE 1

SAMPLING LOCATIONS AND LABORATORY RESULTS

Sample

Number Sample Location Material Description

Approximate

Quantity Result Condition Category

Wallboard

Texture White/Green

Wallboard

Texture White Paint

Wallboard non-detect

White Texture 3% Chrysotile

TSI Pipe Wrap

Yellow Mastic

Good Non-AsbestosNA Attic Insulation Throughout Vermiculite, Blown-in

Cotton Insulation 810 ft

3 assumed

Good Non-Asbestos

AS-18 First Floor Storage 8 LF non-detect Good Non-Asbestos

AS-17 Bedroom #3 South Wall Fiber Board 2,256 ft 2 non-detect

Good Texture is friable RACM

AS-16 Bedroom #3 South Wall (In Wall) Black Wall Paper 3,000 ft 2 non-detect Good Non-Asbestos

AS-15 Bedroom #4 Closet West Wall 1,097 ft

Good Non-Asbestos

AS-14 Bedroom #3 Walk-In-Closet South Wall 1,097 ft 2 non-detect Good Non-Asbestos

AS-13 Bedroom #3 South Wall 1,097 ft 2 non-detect

NA Bedroom #1, Office, and Kitchen Ceilings Acoustic Ceiling Tiles 355 ft 2 assumed Good Non-Asbestos

Appendix A

Laboratory Reports

Asbestos

Detected

Layer Name /

Sample Description

Lab ID Sample

Location

Bulk Asbestos Analysis by Polarized Light Microscopy

Non-Asbestos

Constituents

Laboratory Report

0167022

NVLAP#101926-0

Client ID

Client:

Address: 2410 W. CALIFORNIA AVE

SALT LAKE CITY UT 84104

WASATCH ENVIRONMENTAL

Date Received: 02/24/2016

03/07/2016Date Analyzed:

1139-005Job# / P.O. #:

EMC LABS, INC.

Collected: 02/19/2016

EPA Method: Project Name: KAMAS

Submitted By: AUDRA HEINZELAddress:

Collected By:

9830 S. 51st Street, Suite B109, Phoenix, AZ 85044

Phone: 800-362-3373 or 480-940-5294 - Fax: (480) 893-1726

03/07/2016Date Reported:

EPA 600/R-93/116

Asbestos Type

Cellulose FiberNoLAYER 1 Carpet Foam, Black

None Detected0167022-001

AS-1

1%

Foam Gypsum Quartz Binder/Filler

99%

Cellulose FiberNoLAYER 2 Glue, Yellow/ Black

None Detected <1%

Gypsum

Cellulose FiberYesLAYER 1 Sheet Vinyl, Tan

Chrysotile0167022-002

AS-2

20% 10%

Gypsum Mica Carbonates

70%

Cellulose FiberYesLAYER 2 Mastic, Brown

Chrysotile 7% 3%

Gypsum

90%

Cellulose FiberNoLAYER 1 Floor Tile, Tan/ Gray Streaks

None Detected0167022-003

AS-3

5%

Gypsum Carbonates

95%

Backing, Brown

None Detected 90%

Binder/Filler 10%

Cellulose FiberNoLAYER 3 Mastic, Yellow

None Detected 3%

Gypsum Mica

97%

Cellulose FiberNoLAYER 4 Mastic - Top, Yellow/ Black

None Detected 5%

Gypsum Mica

Layer Name /

Sample Description

Lab ID Sample

Location

Bulk Asbestos Analysis by Polarized Light Microscopy

Non-Asbestos

Constituents

Laboratory Report

0167022

NVLAP#101926-0

Client ID

Client:

Address: 2410 W. CALIFORNIA AVE

SALT LAKE CITY UT 84104

WASATCH ENVIRONMENTAL

Date Received: 02/24/2016

03/07/2016Date Analyzed:

1139-005Job# / P.O. #:

EMC LABS, INC.

Collected: 02/19/2016

EPA Method: Project Name: KAMAS

Submitted By: AUDRA HEINZELAddress:

Collected By:

9830 S. 51st Street, Suite B109, Phoenix, AZ 85044

Phone: 800-362-3373 or 480-940-5294 - Fax: (480) 893-1726

03/07/2016Date Reported:

EPA 600/R-93/116

Asbestos Type

Cellulose FiberNoLAYER 1 Fiber Board, Brown

None Detected0167022-004

AS-4

95%

Binder/Filler 5%

TalcNoLAYER 2 Skim Coat, White/ Off White

None Detected 5%

Gypsum Mica

Fiber Board, Brown

None Detected0167022-005

AS-5

95%

Gypsum

5%

Skim Coat, White/ Off White

None Detected <1%

Gypsum Mica

Fiber Board, Brown

None Detected0167022-006

AS-6

95%

Binder/Filler 5%

TalcNoLAYER 2 Skim Coat, White/ Off White

None Detected 2%

Gypsum Mica

98%

Fiber Board, Brown

None Detected0167022-007

AS-7

95%

Binder/Filler 5%

TalcYesLAYER 2 Skim Coat, White/ Off White

Chrysotile 3% 2%

Carbonates Mica Gypsum

Cellulose FiberNoWallboard, Brown None Detected0167022-008

AS-8

98%

Binder/Filler 2%

Layer Name /

Sample Description

Lab ID Sample

Location

Bulk Asbestos Analysis by Polarized Light Microscopy

Non-Asbestos

Constituents

Laboratory Report

0167022

NVLAP#101926-0

Client ID

Client:

Address: 2410 W. CALIFORNIA AVE

SALT LAKE CITY UT 84104

WASATCH ENVIRONMENTAL

Date Received: 02/24/2016

03/07/2016Date Analyzed:

1139-005Job# / P.O. #:

EMC LABS, INC.

Collected: 02/19/2016

EPA Method: Project Name: KAMAS

Submitted By: AUDRA HEINZELAddress:

Collected By:

9830 S. 51st Street, Suite B109, Phoenix, AZ 85044

Phone: 800-362-3373 or 480-940-5294 - Fax: (480) 893-1726

03/07/2016Date Reported:

EPA 600/R-93/116

Asbestos Type

Cellulose FiberNoLAYER 1 Wallboard, Brown

None Detected0167022-009

AS-9

95%

Binder/Filler 5%

Cellulose FiberNoLAYER 2 Texture, White

None Detected 3%

Gypsum Carbonates Mica

Cellulose Fiber Fibrous Glass

NoLAYER 1 Sheet Vinyl, Gray

None Detected0167022-010

AS-10

25% 3%

Carbonates

72%

Mastic, Yellow

None Detected 5%

Gypsum Carbonates

Cellulose Fiber Synthetic Fiber

NoLAYER 1 Sheet Vinyl, Tan Sparkle

None Detected0167022-011

AS-11

25% 5%

Gypsum Carbonates

70%

Leveling Compound, Off White

None Detected 2%

Gypsum

98%

Cellulose FiberNoFloor Tile, Tan Swirl None Detected0167022-012

AS-12

25%

Gypsum Carbonates

75%

Layer Name /

Sample Description

Lab ID Sample

Location

Bulk Asbestos Analysis by Polarized Light Microscopy

Non-Asbestos

Constituents

Laboratory Report

0167022

NVLAP#101926-0

Client ID

Client:

Address: 2410 W. CALIFORNIA AVE

SALT LAKE CITY UT 84104

WASATCH ENVIRONMENTAL

Date Received: 02/24/2016

03/07/2016Date Analyzed:

1139-005Job# / P.O. #:

EMC LABS, INC.

Collected: 02/19/2016

EPA Method: Project Name: KAMAS

Submitted By: AUDRA HEINZELAddress:

Collected By:

9830 S. 51st Street, Suite B109, Phoenix, AZ 85044

Phone: 800-362-3373 or 480-940-5294 - Fax: (480) 893-1726

03/07/2016Date Reported:

EPA 600/R-93/116

Asbestos Type

Cellulose FiberNoLAYER 1 Wallboard, Brown

None Detected0167022-013

AS-13

90%

10%

TalcNoLAYER 2 Texture, White/ Green

None Detected 3%

Gypsum Carbonates

Wallboard, White

None Detected0167022-014

AS-14

10%

Gypsum Carbonates

Texture / Paint, White Note: Layer is mainly Paint

None Detected 3%

Gypsum Carbonates

Wallboard, White

None Detected0167022-015

AS-15

10%

Gypsum Carbonates

YesLAYER 2 Texture, White

Chrysotile 3%

Carbonates Mica Perlite

Cellulose FiberNoWall Paper, Black/ Brown None Detected0167022-016

AS-16

95%

5%

Cellulose FiberNoFiber Board, Brown None Detected0167022-017

AS-17

98%

Binder/Filler 2%

Layer Name /

Sample Description

Lab ID Sample

Location

Bulk Asbestos Analysis by Polarized Light Microscopy

Non-Asbestos

Constituents

Laboratory Report

0167022

NVLAP#101926-0

Client ID

Client:

Address: 2410 W. CALIFORNIA AVE

SALT LAKE CITY UT 84104

WASATCH ENVIRONMENTAL

Date Received: 02/24/2016

03/07/2016Date Analyzed:

1139-005Job# / P.O. #:

EMC LABS, INC.

Collected: 02/19/2016

EPA Method: Project Name: KAMAS

Submitted By: AUDRA HEINZELAddress:

Collected By:

9830 S. 51st Street, Suite B109, Phoenix, AZ 85044

Phone: 800-362-3373 or 480-940-5294 - Fax: (480) 893-1726

03/07/2016Date Reported:

EPA 600/R-93/116

Asbestos Type

Synthetic FiberNoLAYER 1 TSI-Pipe Wrap, Off White

None Detected0167022-018

AS-18

95%

Binder/Filler 5%

Fibrous Glass Cellulose Fiber

NoLAYER 2 Mastic, Yellow

None Detected 5% 3%

Gypsum

92%

Analyst - Paul Hofer Signatory - Lab Director - Kurt Kettler

Distinctly stratified, easily separable layers of samples are analyzed as subsamples of the whole and are reported separately for each discernible layer. All analyses are derived from calibrated visual estimate and measured in area percent unless otherwise noted. The report applies to the standards or procedures identified and to the sample(s) tested. The test results are not necessarily indicated or representative of the qualities of the lot from which the sample was taken or of apparently identical or similar products, nor do they represent an ongoing quality assurance program unless so noted. These reports are for the exclusive use of the addressed client and that they will not be reproduced wholly or in part for advertising or other purposes over our signature or in connection with our name without special written permission. The report shall not be reproduced except in full, without written approval by our laboratory. The samples not destroyed in testing are retained a maximum of thirty days. The laboratory measurement of uncertainty for the test method is approximately less than 1 by area percent.

Accredited by the National Institute of Standards and Technology, Voluntary Laboratory Accreditation Program for selected test method for asbestos. The accreditation or any reports generated by this laboratory in no way constitutes or implies product certification, approval, or endorsement by the National Institute of Standards and Technology. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. Polarized Light Microscopy may not be consistently reliable in detecting asbestos in floor coverings and similar non-friable organically bound materials.

Layer Name /

Sample Description

Lab ID Sample

Location

Bulk Asbestos Analysis by Polarized Light Microscopy

Non-Asbestos

Constituents

Laboratory Report

0167566

NVLAP#101926-0

Client ID

Client:

Address: 2410 W. CALIFORNIA AVE

SALT LAKE CITY UT 84104

WASATCH ENVIRONMENTAL

Date Received: 03/08/2016

03/11/2016Date Analyzed:

1139-005Job# / P.O. #:

EMC LABS, INC.

Collected: 02/19/2016

EPA Method: Project Name: KAMAS

Submitted By: AUDRA HEINZELAddress: POINT COUNT VIA EMC LAB #167022

Collected By:

9830 S. 51st Street, Suite B109, Phoenix, AZ 85044

Phone: 800-362-3373 or 480-940-5294 - Fax: (480) 893-1726

03/11/2016Date Reported:

EPA 600/R-93/116

Asbestos Type

TalcYesSkim Coat, White/ Off White Chrysotile0167566-001

AS-7

3.6% 1.8%

Carbonates Mica Gypsum

94.6%

400 Pt. POINT COUNT

YesTexture, White Chrysotile0167566-002

AS-15

3.2%

Carbonates Mica Perlite

96.8%

400 Pt. POINT COUNT

Analyst - Kenneth Scheske Signatory - Lab Director - Kurt Kettler

Distinctly stratified, easily separable layers of samples are analyzed as subsamples of the whole and are reported separately for each discernible layer. All analyses are derived from calibrated visual estimate and measured in area percent unless otherwise noted. The report applies to the standards or procedures identified and to the sample(s) tested. The test results are not necessarily indicated or representative of the qualities of the lot from which the sample was taken or of apparently identical or similar products, nor do they represent an ongoing quality assurance program unless so noted. These reports are for the exclusive use of the addressed client and that they will not be reproduced wholly or in part for advertising or other purposes over our signature or in connection with our name without special written permission. The report shall not be reproduced except in full, without written approval by our laboratory. The samples not destroyed in testing are retained a maximum of thirty days. The laboratory measurement of uncertainty for the test method is approximately less than 1 by area percent.

Accredited by the National Institute of Standards and Technology, Voluntary Laboratory Accreditation Program for selected test method for asbestos. The accreditation or any reports generated by this laboratory in no way constitutes or implies product certification, approval, or endorsement by the National Institute of Standards and Technology. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. Polarized Light Microscopy may not be consistently reliable in detecting asbestos in floor coverings and similar non-friable organically bound materials.

Appendix B

Inspector Certification