UFGS 09 90 00 Paints and Coatings.pdf

USACE / NAVFAC / AFCEC / NASA UFGS- 09 90 00 ( Febr uar y 2021)

Pr epar i ng Act i v i t y: NAVFAC Superseding UFGS- 09 90 00 ( May 2011)

UNI FI ED FACI LI TI ES GUI DE SPECI FI CATI ONS

Ref er ences ar e i n agr eement wi t h UMRL dat ed Jul y 2021

SECTION TABLE OF CONTENTS

DIVISION 09 - FINISHES

SECTION 09 90 00

PAINTS AND COATINGS

02/21

PART 1 GENERAL

1.1 RELATED REQUIREMENTS

1.1.1 Painting Included

1.1.1.1 Exterior Painting

1.1.1.2 Interior Painting

1.1.2 Painting Excluded

1.1.3 Mechanical and Electrical Painting

1.1.3.1 Fire Extinguishing Sprinkler Systems

1.1.4 Exterior Painting of Site Work Items

1.1.5 Miscellaneous Painting

1.1.5.1 Lettering [Building ][Room Number(s)]

1.1.5.2 Obstructions To Aviation

1.2 REFERENCES

1.3 DEFINITIONS

1.3.1 Qualification Testing

1.3.2 Batch Quality Conformance Testing

1.3.3 Coating

1.3.4 DFT or dft

1.3.5 DSD

1.3.6 EXT

1.3.7 INT

1.3.8 Loose Paint

1.3.9 micron / microns

1.3.10 mil / mils

1.3.11 mm

1.3.12 MPI Gloss Levels

1.3.13 MPI System Number

1.3.14 Paint

1.3.15 REX

1.3.16 RIN

1.4 SCHEDULING

1.5 SUBMITTALS

1.6 QUALITY ASSURANCE

SECTION 09 90 00 Page 1

1.6.1 Regulatory Requirements

1.6.1.1 Environmental Protection

1.6.1.2 Lead Content

1.6.1.3 Chromate Content

1.6.1.4 Asbestos Content

1.6.1.5 Mercury Content

1.6.1.6 Silica

1.6.1.7 Human Carcinogens

1.6.1.8 Carbon Based Fibers / Tubes

1.6.2 Coating Contractor's Qualification

1.6.3 SSPC QP 1 Certification

1.6.4 Approved Products List

1.6.5 Paints and Coatings Indoor Air Quality Certifications

1.6.6 Field Samples and Tests

1.6.6.1 Sampling Procedure

1.6.6.2 Testing Procedure

1.6.7 Textured Wall Coating System

1.6.8 Sample Textured Wall Coating System Mock-Up

1.7 PACKAGING, LABELING, AND STORAGE

1.8 SAFETY AND HEALTH

1.8.1 Toxic Materials

1.9 ENVIRONMENTAL REQUIREMENTS

1.9.1 Coatings

1.9.2 Post-Application

PART 2 PRODUCTS

2.1 MATERIALS

2.2 COLOR CODING FOR SHORE-TO SHIP UTILITY CONNECTIONS

2.3 COLOR SELECTION OF FINISH COATS

PART 3 EXECUTION

3.1 PROTECTION OF AREAS AND SPACES NOT TO BE PAINTED

3.2 REPUTTYING AND REGLAZING

3.3 RESEALING OF EXISTING EXTERIOR JOINTS

3.3.1 Surface Condition

3.3.2 Backstops

3.3.3 Primer and Bond Breaker

3.3.4 Ambient Temperature

3.3.5 Exterior Sealant

3.3.6 Cleaning

3.4 SURFACE PREPARATION

3.4.1 Additional Requirements for Preparation of Surfaces With

Existing Coatings

3.4.2 Existing Coated Surfaces with Minor Defects

3.4.3 Removal of Existing Coatings

3.4.4 Substrate Repair

3.5 PREPARATION OF METAL SURFACES

3.5.1 Existing and New Ferrous Surfaces

3.5.2 Final Ferrous Surface Condition:

3.5.2.1 Tool Cleaned Surfaces

3.5.2.2 Abrasive Blast Cleaned Surfaces

3.5.2.3 Waterjet Cleaned Surfaces

3.5.3 Galvanized Surfaces

3.5.4 Non-Ferrous Metallic Surfaces

3.5.5 Terne-Coated Metal Surfaces

3.5.6 Existing Surfaces with a Bituminous or Mastic-Type Coating

3.6 PREPARATION OF CONCRETE AND CEMENTITIOUS SURFACE

SECTION 09 90 00 Page 2

3.6.1 Concrete and Masonry

3.6.2 Gypsum Board, Plaster, and Stucco

3.6.2.1 Surface Cleaning

3.6.2.2 Repair of Minor Defects

3.6.2.3 Allowable Moisture Content

3.6.3 Existing Asbestos Cement Surfaces

3.7 PREPARATION OF WOOD AND PLYWOOD SURFACES

3.7.1 New[, Existing Uncoated,][ and][ Existing Coated] Plywood and

Wood Surfaces, Except Floors:

3.7.2 Wood Floor Surfaces, Natural Finish

3.7.3 Interior Wood Surfaces, Stain Finish

3.7.4 Water Blasting of Existing Coated Wood Surfaces:

3.8 APPLICATION

3.8.1 Coating Application

3.8.2 Mixing and Thinning of Paints

3.8.3 Two-Component Systems

3.8.4 Coating Systems

3.9 COATING SYSTEMS FOR METAL

3.10 COATING SYSTEMS FOR CONCRETE AND CEMENTITIOUS SUBSTRATES

3.11 COATING SYSTEMS FOR WOOD AND PLYWOOD

3.12 PIPING IDENTIFICATION

3.13 INSPECTION AND ACCEPTANCE

3.14 WASTE MANAGEMENT

3.15 PAINT TABLES

3.15.1 Exterior Paint Tables

3.15.1.1 MPI Division 3: Exterior Concrete Paint Table

3.15.1.2 MPI Division 4: Exterior Concrete Masonry Units Paint

Table

3.15.1.3 MPI Division 5: Exterior Metal, Ferrous and Non-Ferrous

Paint Table

3.15.1.4 MPI Division 6: Exterior Wood; Dressed Lumber, Paneling, Decking, Shingles Paint Table

3.15.1.5 MPI Division 9: Exterior Stucco Paint Table

3.15.1.6 MPI Division 10: Exterior Cloth Coverings and Bituminous

Coated Surfaces Paint Table

3.15.2 Interior Paint Tables

3.15.2.1 MPI Division 3: Interior Concrete Paint Table

3.15.2.2 MPI Division 4: Interior Concrete Masonry Units Paint

Table

3.15.2.3 MPI Division 5: Interior Metal, Ferrous and Non-Ferrous

Paint Table

3.15.2.4 MPI Division 6: Interior Wood Paint Table

3.15.2.5 MPI Division 9: Interior Plaster, Gypsum Board, Textured

Surfaces Paint Table

-- End of Section Table of Contents --

SECTION 09 90 00 Page 3

USACE / NAVFAC / AFCEC / NASA UFGS- 09 90 00 ( Febr uar y 2021)

Pr epar i ng Act i v i t y: NAVFAC Superseding UFGS- 09 90 00 ( May 2011)

UNI FI ED FACI LI TI ES GUI DE SPECI FI CATI ONS

Ref er ences ar e i n agr eement wi t h UMRL dat ed Jul y 2021

SECTION 09 90 00

PAINTS AND COATINGS

02/21

NOTE: Thi s gui de speci f i cat i on cover s t he r equi r ement s f or pai nt i ng of new and exi st i ng, i nt er i or and ext er i or subst r at es, i ncl udi ng masonr y, concr et e, met al , wood, and ot her mi scel l aneous materials.

Adher e t o UFC 1-300-02 Uni f i ed Faci l i t i es Gui de Speci f i cat i ons ( UFGS) For mat St andar d when edi t i ng t hi s gui de speci f i cat i on or pr epar i ng new pr oj ect speci f i cat i on sect i ons. Edi t t hi s gui de speci f i cat i on f or pr oj ect speci f i c r equi r ement s by addi ng, del et i ng, or r evi s i ng t ext . For br acket ed i t ems, choose appl i cabl e i t em( s) or i nser t appr opr i at e i nf or mat i on.

Remove i nf or mat i on and r equi r ement s not r equi r ed i n r espect i ve pr oj ect , whet her or not br acket s ar e present.

Comment s, suggest i ons and r ecommended changes f or t hi s gui de speci f i cat i on ar e wel come and shoul d be submi t t ed as a Criteria Change Request (CCR) .

NOTE: Thi s gui de speci f i cat i on i ncl udes t ai l or i ng f or ARMY and NAVY pr oj ect s, and f or I NTERI OR and EXTERI OR pai nt i ng. Wher e an Edi t or ' s Not e st at es a par agr aph i s t ai l or ed f or a Ser vi ce or pai nt i ng t ype, t he cont ent of t he par agr aph, or a por t i on of t he par agr aph, i s sui t ed speci f i cal l y t o be i ncl uded onl y f or t hat Ser vi ce or pai nt i ng t ype.

NOTE: Thi s Gui de Speci f i cat i on i s used i n t he pr epar at i on of pr oj ect speci f i cat i ons f or Depar t ment of Def ense f aci l i t i es:

1. Bui l di ngs;

SECTION 09 90 00 Page 4

2. Rel at ed mechani cal , el ect r i cal , and mi scel l aneous i t ems; and

3. Shor e- t o- shi p ut i l i t y connect i ons.

Thi s gui de speci f i cat i on has been pr epar ed t o addr ess t he r equi r ement s of r out i ne mai nt enance pai nt i ng when modi f i ed t o i ncl ude or ut i l i ze mai nt enance opt i ons.

Thi s gui de speci f i cat i on DOES NOT addr ess hi gh- per f or mance or speci al t y coat i ng r equi r ement s, or pr ot ect i ve coat i ng of i ndust r i al st r uct ur es or f aci l i t i es, i ncl udi ng but not l i mi t ed t o:

1. Tower s;

2. Pi l i ngs;

3. Pavement mar ki ngs;

4. I t ems r equi r i ng speci al i zed t r eat ment due t o pecul i ar usage;

5. Pet r ol eum st or age f aci l i t i es;

6. Wat er st or age f aci l i t i es;

7. Wat er f r ont f aci l i t i es, except shor e- t o- shi p ut i l i t y connect i ons; and

8. Hangar s

I f such i t ems ar e i n t he pr oj ect i ncl ude i n a separ at e sect i on or modi f y t hi s sect i on accor di ngl y. The f ol l owi ng gui de speci f i cat i ons ar e exampl es of t hose avai l abl e f or speci f i c ser vi ce condi t i ons not ed, and may be modi f i ed t o pr ovi de f or r el at ed ser vi ce condi t i ons:

1. Sect i on 09 97 23 METALLI C TYPE CONDUCTI VE/ SPARK RESI STANT CONCRETE FLOOR FI NI SH. Thi s speci f i cat i on cover s t he r equi r ement s f or met al l i c t ype conduct i ve/ spar k r esi st ant concr et e f l oor f i ni sh f or or dnance and ot her s i mi l ar st r uct ur es.

2. Sect i on 09 97 02 PAI NTI NG: HYDRAULI C STRUCTURES. Thi s speci f i cat i on cover s t he pai nt i ng of hydr aul i c st r uct ur es l ocat ed i n f r esh wat er such as l ocks and dams.

3. Sect i on 09 97 13. 27 HI GH PERFORMANCE COATI NG FOR STEEL STRUCTURES. Thi s speci f i cat i on i s usabl e f or any st eel st r uct ur e exposed t o weat her , and i s usabl e f or ot her pur poses as wel l , such as hangar st r uct ur es, encl osed swi mmi ng pool st r uct ur es, and most s i t uat i ons r equi r i ng hi gh- per f or mance pr ot ect i ve coat i ng syst ems.

4. Sect i on 09 97 13. 16 I NTERI OR COATI NG OF WELDED STEEL WATER TANKS. Thi s gui de speci f i cat i on cover s t he r equi r ement s f or pol yami de epoxy coat i ng syst em f or i nt er i or of newl y const r uct ed Navy and Ai r For ce wat er t anks, pot abl e and non- pot abl e, wher e shop appl i ed coat i ngs ar e not bei ng consi der ed.

5. Sect i on 09 97 13. 15 LOW VOC POLYSULFI DE I NTERI OR COATI NG OF WELDED STEEL PETROLEUM FUEL TANKS. Thi s

SECTION 09 90 00 Page 5 cover s t he r equi r ement s f or a Low VOC ( l ess t han 50 gr ams/ l i t er ) t wo- coat modi f i ed epoxy novol ac pol ysul f i de coat i ng syst em f or i nt er i or s of newl y const r uct ed Navy bul k f uel st or age t anks. Wi t h pr oper modi f i cat i on i t can al so be used f or mai nt enance appl i cat i ons.

6. Sect i on 09 97 13. 26 COATI NG OF STEEL WATERFRONT

STRUCTURES, ZERO VOC, ( SZC) SPLASH ZONE COATI NG.

Thi s cover s t he r equi r ement s f or a Low VOC t wo- coat modi f i ed epoxy novol ac pol ysul f i de coat i ng syst em f or newl y const r uct ed st eel st r uct ur es i n a sal t wat er envi r onment especi al l y exposed t o t he spl ash zone ar ea. The syst em may al so be appl i ed t o st eel st r uct ur es i n a f r esh wat er envi r onment . Wi t h modi f i cat i on f or speci f i c l ocat i on and r equi r ement s i t can al so be used f or mai nt enance appl i cat i ons.

Thi s gui de speci f i cat i on gener al l y cont ai ns onl y t wo t ypes of coat i ng syst ems, sol vent based and wat er based. I f di f f er ent syst ems ar e r equi r ed r egi onal l y, or f or speci al needs, modi f y t he gui de accordingly.

PART 1 GENERAL

1.1 RELATED REQUIREMENTS

NOTE: I ndi cat e t ype and ext ent of wor k on dr awi ngs. Speci f i c quant i t i es shoul d not be ci t ed i n t he speci f i cat i on. I ndi cat e on t he dr awi ngs t he l i near amount of exi st i ng put t y, gl azi ng compound, seal ant or caul k i ng t o be r epl aced wi t h new mat er i al and quant i f y t he ar ea of exi st i ng coat i ng t o be r emoved by met hods speci f i ed f or each subst r at e material.

1.1.1 Painting Included

Where a space or surface is indicated to be painted, include the following unless indicated otherwise.

a. Surfaces behind portable objects and surface mounted articles readily detachable by removal of fasteners, such as screws and bolts.

b. New factory finished surfaces that require identification or color coding and factory finished surfaces that are damaged during performance of the work.

c. Existing coated surfaces that are damaged during performance of the work.

1.1.1.1 Exterior Painting

NOTE: The f ol l owi ng subpar agr aph i s t ai l or ed f or

SECTION 09 90 00 Page 6 i ncl usi on i n pr oj ect s wi t h ext er i or pai nt i ng.

Choose br acket ed i t ems accor di ng t o scope of pr oj ect .

Includes new surfaces[, existing coated surfaces,][ and ][existing uncoated surfaces,] of the building[s] and appurtenances. Also included are existing coated surfaces made bare by cleaning operations.

1.1.1.2 Interior Painting

NOTE: The f ol l owi ng subpar agr aph i s t ai l or ed f or i ncl usi on i n pr oj ect s wi t h i nt er i or pai nt i ng.

Choose br acket ed i t ems accor di ng t o scope of pr oj ect .

Includes new surfaces[, existing uncoated surfaces,][ and ][existing coated surfaces] of the building[s] and appurtenances as indicated and existing coated surfaces made bare by cleaning operations. Where a space or surface is indicated to be painted, include the following items, unless indicated otherwise.

a. Exposed columns, girders, beams, joists, and metal deck; and

b. Other contiguous surfaces.

1.1.2 Painting Excluded

Do not paint the following unless indicated otherwise.

a. Surfaces concealed and made inaccessible by panelboards, fixed ductwork, machinery, and equipment fixed in place.

b. Surfaces in concealed spaces. Concealed spaces are defined as enclosed spaces above suspended ceilings, furred spaces, attic spaces, crawl spaces, elevator shafts and chases.

c. Steel to be embedded in concrete.

d. Copper, stainless steel, aluminum, anodized aluminum, brass, and lead except existing coated surfaces.

e. Hardware, fittings, and other factory finished items.

[ f. Do not paint surfaces in the following areas: [_____].

] 1.1.3 Mechanical and Electrical Painting

NOTE: Choose br acket ed i t ems i n par agr aph bel ow accor di ng t o scope of pr oj ect .

Includes field coating of [interior][ and ][exterior] new[ and existing] surfaces.

a. Where a space or surface is indicated to be painted, include the

SECTION 09 90 00 Page 7 following items unless indicated otherwise.

(1) Exposed piping, conduit, and ductwork;

(2) Supports, hangers, air grilles, and registers;

(3) Miscellaneous metalwork and insulation coverings.

[ b. Do not paint the following, unless indicated otherwise:

[ (1) New zinc-coated, aluminum, and copper surfaces under insulation

][ (2) New aluminum jacket on piping

][ (3) New interior ferrous piping under insulation.

]][ 1.1.3.1 Fire Extinguishing Sprinkler Systems

Clean, pretreat, prime, and paint new fire extinguishing sprinkler systems including valves, piping, conduit, hangers, supports, miscellaneous metalwork, and accessories. Apply coatings to clean, dry surfaces, using clean brushes.

] [ 1.1.4 Exterior Painting of Site Work Items

NOTE: The f ol l owi ng par agr aph i s t ai l or ed f or i ncl usi on i n pr oj ect s wi t h ext er i or pai nt i ng.

I nser t l i s t of Si t e Wor k I t ems t o be pai nt ed i n t abl e bel ow, such as hand r ai l s, f i r e ext i ngui shi ng syst ems, door s.

Field coat the following items:

New Surfaces Existing Surfaces a.

b.

c.

] 1.1.5 Miscellaneous Painting

1.1.5.1 Lettering [Building ][Room Number(s)]

Provide lettering [as scheduled on the drawings][block][Gothic] type, [black enamel][water-type decalcomania, finished with a protective coating of spar varnish]. Samples must be approved before application.

[ 1.1.5.2 Obstructions To Aviation

NOTE: Speci f y by name st r uct ur es such as smokest acks, pol es, and bui l di ngs whi ch have been i dent i f i ed as obst r uct i on t o avi at i on. Ver i f y t hat

SECTION 09 90 00 Page 8 t he st r uct ur es so i dent i f i ed ar e not speci f i ed t o be pai nt ed i n t he sect i ons speci f y i ng t he st r uct ur es so t hat pai nt i ng wi l l not be speci f i ed t wi ce.

Coor di nat e wi t h FAA f or al t er nat e col or s and patterns.

Paint the following obstructions to aviation in the pattern and color prescribed by FAA AC 70/7460-1 : [smokestacks][poles][buildings][_____]

] 1.2 REFERENCES

NOTE: Thi s par agr aph i s used t o l i s t t he publ i cat i ons c i t ed i n t he t ext of t he gui de speci f i cat i on. The publ i cat i ons ar e r ef er r ed t o i n t he t ext by basi c desi gnat i on onl y and l i s t ed i n t hi s par agr aph by or gani zat i on, desi gnat i on, dat e, and t i t l e.

Use t he Ref er ence Wi zar d' s Check Ref er ence f eat ur e when you add a Ref er ence I dent i f i er ( RI D) out si de of t he Sect i on' s Ref er ence Ar t i c l e t o aut omat i cal l y pl ace t he r ef er ence i n t he Ref er ence Ar t i c l e. Al so use t he Ref er ence Wi zar d' s Check Ref er ence f eat ur e t o updat e t he i ssue dat es.

Ref er ences not used i n t he t ext wi l l aut omat i cal l y be del et ed f r om t hi s sect i on of t he pr oj ect speci f i cat i on when you choose t o r econci l e r ef er ences i n t he publ i sh pr i nt pr ocess.

The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text by the basic designation only.

AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGIENISTS (ACGIH)

ACGIH 0100 (2017; Suppl 2020) Documentation of the Threshold Limit Values and Biological Exposure Indices

AMERICAN SOCIETY OF MECHANICAL ENGINEERS (ASME)

ASME A13.1 (2020) Scheme for the Identification of Piping Systems

ASTM INTERNATIONAL (ASTM)

ASTM C920 (2018) Standard Specification for Elastomeric Joint Sealants

ASTM D235 (2002; R 2012) Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent)

ASTM D523 (2014; R 2018) Standard Test Method for Specular Gloss

SECTION 09 90 00 Page 9

ASTM D2824/D2824M (2018) Standard Specification for Aluminum-Pigmented Asphalt Roof Coatings, Non-Fibered, and Fibered without Asbestos

ASTM D4214 (2007; R 2015) Standard Test Method for Evaluating the Degree of Chalking of Exterior Paint Films

ASTM D4263 (1983; R 2018) Standard Test Method for Indicating Moisture in Concrete by the Plastic Sheet Method

ASTM D4444 (2013; R 2018) Standard Test Method for Laboratory Standardization and Calibration of Hand-Held Moisture Meters

ASTM D6386 (2016a) Standard Practice for Preparation of Zinc (Hot-Dip Galvanized) Coated Iron and Steel Product and Hardware Surfaces for Painting

ASTM F1869 (2016a) Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride

CENTERS FOR DISEASE CONTROL AND PREVENTION (CDC)

Intelligence Bulletin 65 (2013) Occupational Exposure to Carbon Nanotubes and Nanofibers

MASTER PAINTERS INSTITUTE (MPI)

MPI 1 (2012) Aluminum Paint

MPI 2 (2012) Aluminum Heat Resistant Enamel (up to 427 C and 800 F

MPI 3 (2016) Primer, Alkali Resistant, Water Based

MPI 4 (2016) Interior/Exterior Latex Block Filler

MPI 5 (2015) Primer, Exterior Alkyd Wood

MPI 6 (2015) Primer, Exterior Latex Wood

MPI 8 (2016) Alkyd, Exterior Flat (MPI Gloss Level I)

MPI 9 (2016) Alkyd, Exterior Gloss (MPI Gloss Level 6)

MPI 10 (2016) Latex, Exterior Flat (MPI Gloss Level 1)

MPI 11 (2016) Latex, Exterior Semi-Gloss, MPI Gloss Level 5

MPI 13 (2016) Stain, Exterior Solvent-Based, SECTION 09 90 00 Page 10

Semi-Transparent

MPI 16 (2016) Stain, Exterior, Water Based, Solid Hide

MPI 17 (2016) Primer, Bonding, Water Based

MPI 19 (2012) Primer, Zinc Rich, Inorganic

MPI 21 (2012) Heat Resistant Coating, (Up to 205°C/402°F), MPI Gloss Level 6

MPI 22 (2012) Aluminum Paint, High Heat (up to 590° C/1100° F)

MPI 23 (2015) Primer, Metal, Surface Tolerant

MPI 27 (2016) Floor Enamel, Alkyd, Gloss (MPI Gloss Level 6)

MPI 31 (2012) Varnish, Polyurethane, Moisture Cured, Gloss (MPI Gloss Level 6)

MPI 38 (2016) Elastomeric Coating, Exterior, Water Based, Non-Flat

MPI 39 (2018) Primer, Latex, for Interior Wood

MPI 42 (2012) Textured Coating, Latex, Flat

MPI 44 (2016) Latex, Interior, (MPI Gloss Level 2)

MPI 45 (2016) Primer Sealer, Interior Alkyd

MPI 46 (2016) Undercoat, Enamel, Interior

MPI 47 (2016) Alkyd, Interior, Semi-Gloss (MPI Gloss Level 5)

MPI 48 (2016) Alkyd, Interior, Gloss (MPI Gloss Level 6-7)

MPI 49 (2015) Alkyd, Interior, Flat (MPI Gloss Level 1)

MPI 50 (2015) Primer Sealer, Latex, Interior

MPI 51 (2016) Alkyd, Interior, (MPI Gloss Level 3)2

MPI 52 (2016) Latex, Interior, (MPI Gloss Level 3)

MPI 54 (2016) Latex, Interior, Semi-Gloss (MPI Gloss Level 5)

MPI 56 (2012) Varnish, Interior, Polyurethane, Oil Modified, Gloss

MPI 57 (2012) Varnish, Interior, Polyurethane, SECTION 09 90 00 Page 11

Oil Modified, Satin

MPI 59 (2016) Floor Paint, Alkyd, Low Gloss

MPI 60 (2016) Floor Paint, Latex, Low Gloss

MPI 68 (2016) Floor Paint, Latex, Gloss

MPI 71 (2012) Varnish, Polyurethane, Moisture Cured, Flat (MPI Gloss Level 1)

MPI 72 (2016) Polyurethane, Two-Component, Pigmented, Gloss (MPI Gloss Level 6-7)

MPI 76 (2016) Primer, Alkyd, Quick Dry, for Metal

MPI 77 (2015) Epoxy, Gloss

MPI 79 (2016) Primer, Alkyd, Anti-Corrosive for Metal

MPI 90 (2012) Stain, Semi-Transparent, for Interior Wood

MPI 94 (2016) Alkyd, Exterior, Semi-Gloss (MPI Gloss Level 5)

MPI 95 (2015) Primer, Quick Dry, for Aluminum

MPI 101 (2016) Primer, Epoxy, Anti-Corrosive, for Metal

MPI 107 (2016) Primer, Rust-Inhibitive, Water Based

MPI 108 (2015) Epoxy, High Build, Low Gloss

MPI 113 (2018) Elastomeric, Pigmented, Exterior, Water Based, Flat

MPI 116 (2012) Block Filler, Epoxy

MPI 119 (2016) Latex, Exterior, Gloss (MPI Gloss Level 6)

MPI 120 (2020) Epoxy, High Build, Self Priming, Low Gloss

MPI 134 (2015) Primer, Galvanized, Water Based

MPI 138 (2016) Latex, Interior, High Performance Architectural, (MPI Gloss Level 2)

MPI 139 (2016) Latex, Interior, High Performance Architectural, (MPI Gloss Level 3)

MPI 140 (2016) Latex, Interior, High Performance Architectural, (MPI Gloss Level 4)

MPI 141 (2016) Latex, Interior, High Performance

SECTION 09 90 00 Page 12

Architectural, Semi-Gloss (MPI Gloss Level 5)

MPI 144 (2016) Latex, Interior, Institutional Low Odor/VOC, (MPI Gloss Level 2)

MPI 145 (2016) Latex, Interior, Institutional Low Odor/VOC, ( MPI Gloss Level 3)

MPI 146 (2016) Latex, Interior, Institutional Low Odor/VOC, (MPI Gloss Level 4)

MPI 147 (May 2016) Latex, Interior, Institutional Low Odor/VOC, Semi-Gloss (MPI Gloss Level 5)

MPI 149 (2016) Primer Sealer, Interior, Institutional Low Odor/VOC

MPI 151 (2016) Light Industrial Coating, Interior, Water Based (MPI Gloss Level 3)

MPI 153 (2016) Light Industrial Coating, Interior, Water Based, Semi-Gloss (MPI Gloss Level 5)

MPI 154 (2016) Light Industrial Coating, Interior, Water Based, Gloss (MPI Gloss Level 6)

MPI 161 (2016) Light Industrial Coating, Exterior, Water Based ( MPI Gloss Level 3)

MPI 163 (2016) Light Industrial Coating, Exterior, Water Based, Semi-Gloss (MPI Gloss Level 5)

MPI 164 (2016) Light Industrial Coating, Exterior, Water Based, Gloss (MPI Gloss Level 6)

MPI 177 (2020) Epoxy, Semi-Gloss (MPI Gloss Level 5)

MPI 214 (2016) Latex, Exterior (MPI Gloss Level 2)

MPI ASM (2019) Architectural Painting Specification Manual

MPI GPS-1-14 (2014) Green Performance Standard GPS-1-14

MPI GPS-2-14 (2014) Green Performance Standard GPS-2-14

MPI MRM (2015) Maintenance Repainting Manual

SOCIETY FOR PROTECTIVE COATINGS (SSPC)

SSPC 7/NACE No.4 (2007) Brush-Off Blast Cleaning

SSPC Glossary (2011) SSPC Protective Coatings Glossary

SSPC Guide 6 (2015) Guide for Containing Surface Preparation Debris Generated During Paint

SECTION 09 90 00 Page 13

Removal Operations

SSPC Guide 7 (2015) Guide to the Disposal of Lead-Contaminated Surface Preparation Debris

SSPC PA 1 (2016) Shop, Field, and Maintenance Coating of Metals

SSPC QP 1 (2019) Standard Procedure for Evaluating the Qualifications of Industrial/Marine Painting Contractors (Field Application to Complex Industrial Steel Structures and Other Metal Components)

SSPC SP 1 (2015) Solvent Cleaning

SSPC SP 2 (2018) Hand Tool Cleaning

SSPC SP 3 (2018) Power Tool Cleaning

SSPC SP 6/NACE No.3 (2007) Commercial Blast Cleaning

SSPC SP 10/NACE No. 2 (2007) Near-White Blast Cleaning

SSPC VIS 1 (2002; E 2004) Guide and Reference Photographs for Steel Surfaces Prepared by Dry Abrasive Blast Cleaning

SSPC VIS 3 (2004) Guide and Reference Photographs for Steel Surfaces Prepared by Hand and Power Tool Cleaning

SSPC VIS 4/NACE VIS 7 (1998; E 2000; E 2004) Guide and Reference Photographs for Steel Surfaces Prepared by Waterjetting

SSPC-SP WJ-1/NACE WJ-1 (2012) Clean to Bare Substrate, Waterjet Cleaning of Metals

SSPC-SP WJ-2/NACE WJ-2 (2012) Very Thorough Cleaning, Waterjet Cleaning of Metals

SSPC-SP WJ-3/NACE WJ-3 (2012) Thorough Cleaning, Waterjet Cleaning of Metals

SSPC-SP WJ-4/NACE WJ-4 (2012) Light Cleaning, Waterjet Cleaning of Metals

SOCIETY OF AUTOMOTIVE ENGINEERS INTERNATIONAL (SAE)

SAE AMS-STD-595A (2017) Colors used in Government Procurement

U.S. ARMY CORPS OF ENGINEERS (USACE)

EM 385-1-1 (2014) Safety and Health Requirements Manual

SECTION 09 90 00 Page 14

U.S. DEPARTMENT OF DEFENSE (DOD)

MIL-PRF-680 (2010; Rev C; Notice 1 2015) Degreasing Solvent

MIL-STD-101 (2014; Rev C) Color Code for Pipelines and for Compressed Gas Cylinders

U.S. ENVIRONMENTAL PROTECTION AGENCY (EPA)

EPA Method 24 (2000) Determination of Volatile Matter Content, Water Content, Density, Volume Solids, and Weight Solids of Surface Coatings

U.S. FEDERAL AVIATION ADMINISTRATION (FAA)

FAA AC 70/7460-1 (2016; Rev L; Change 2) Obstruction Marking and Lighting

U.S. GENERAL SERVICES ADMINISTRATION (GSA)

FED-STD-313 (2018) Material Safety Data, Transportation Data and Disposal Data for Hazardous Materials Furnished to Government Activities

U.S. NATIONAL ARCHIVES AND RECORDS ADMINISTRATION (NARA)

29 CFR 1910.1000 Air Contaminants

29 CFR 1910.1001 Asbestos

29 CFR 1910.1025 Lead

29 CFR 1926.62 Lead

1.3 DEFINITIONS

1.3.1 Qualification Testing

Qualification testing is the performance of all test requirements listed in the product specification. This testing is accomplished by MPI to qualify each product for the MPI Approved Product List, and may also be accomplished by Contractor's third-party testing lab if an alternative to Batch Quality Conformance Testing by MPI is desired.

1.3.2 Batch Quality Conformance Testing

Batch quality conformance testing determines that the product provided is the same as the product qualified to the appropriate product specification. This testing must be accomplished by an MPI testing lab.

1.3.3 Coating

SSPC Glossary ; (1) A liquid, liquefiable, or mastic composition that is converted to a solid protective, decorative, or functional adherent film after application as a thin layer; (2) Generic term for paint, lacquer, enamel.

SECTION 09 90 00 Page 15

1.3.4 DFT or dft

Dry film thickness, the film thickness of the fully cured, dry paint or coating.

1.3.5 DSD

Degree of Surface Degradation, the MPI system of defining degree of surface degradation. Five levels are generically defined under the Assessment sections in the MPI MRM, MPI Maintenance Repainting Manual.

1.3.6 EXT

NOTE: The f ol l owi ng par agr aph i s t ai l or ed f or i ncl usi on i n pr oj ect s wi t h ext er i or pai nt i ng.

MPI short term designation for an exterior coating system.

1.3.7 INT

NOTE: The f ol l owi ng par agr aph i s t ai l or ed f or i ncl usi on i n pr oj ect s wi t h i nt er i or pai nt i ng.

MPI short term designation for an interior coating system.

1.3.8 Loose Paint

Paint or coating that can be removed with a dull putty knife.

1.3.9 micron / microns

The metric measurement for 0.001 mm or one one-thousandth of a millimeter.

1.3.10 mil / mils

The English measurement for 0.001 in or one one-thousandth of an inch.

1.3.11 mm

The metric measurement for millimeter, 0.001 meter or one one-thousandth of a meter.

1.3.12 MPI Gloss Levels

MPI system of defining gloss. Seven gloss levels (G1 to G7) are generically defined under the Evaluation sections of the MPI Manuals.

Traditionally, Flat refers to G1/G2, Eggshell refers to G3, Semigloss refers to G5, and Gloss refers to G6.

Gloss levels are defined by MPI as follows:

SECTION 09 90 00 Page 16

Gloss Level Description Units at 60 degree angle

Units at 80 degree angle

G1 Matte or Flat 0 to 5 10 max

G2 Velvet 0 to 10 10 to 35

G3 Eggshell 10 to 25 10 to 35

G4 Satin 20 to 35 35 min

G5 Semi-Gloss 35 to 70

G6 Gloss 70 to 85

G7 High Gloss

Gloss is tested in accordance with ASTM D523. Historically, the Government has used Flat (G1 / G2), Eggshell (G3), Semi-Gloss (G5), and Gloss (G6).

1.3.13 MPI System Number

The MPI coating system number in each MPI Division found in either the MPI Architectural Painting Specification Manual or the Maintenance Repainting Manual and defined as an exterior (EXT/REX) or interior system (INT/RIN).

1.3.14 Paint

SSPC Glossary ; (1) Any pigmented liquid, liquefiable, or mastic composition designed for application to a substrate in a thin layer that is converted to an opaque solid film after application. Used for protection, decoration, identification, or to serve some other functional purposes; (2) Application of a coating material.

1.3.15 REX

NOTE: The f ol l owi ng par agr aph i s t ai l or ed f or i ncl usi on i n pr oj ect s wi t h ext er i or pai nt i ng.

MPI short term designation for an exterior coating system used in repainting projects or over existing coating systems.

1.3.16 RIN

NOTE: The f ol l owi ng par agr aph i s t ai l or ed f or i ncl usi on i n pr oj ect s wi t h i nt er i or pai nt i ng.

MPI short term designation for an interior coating system used in repainting projects or over existing coating systems.

1.4 SCHEDULING

NOTE: Thi s Ar t i c l e i s t ai l or ed f or i ncl usi on i n

SECTION 09 90 00 Page 17

NAVY pr oj ect s onl y.

Mat er i al s t hat adsor b VOCs i ncl ude car pet s, t ext i l es, unpr i med gypsum wal l boar d, and acoust i cal cei l i ng panel s. Add any of t hese mat er i al s t hat ar e i ncl uded i n t he pr oj ect and ot her adsor bi ng mat er i al s i nt o t he empt y br acket .

Allow paint, polyurethane, varnish, and wood stain installations to cure prior to the installation of materials that adsorb VOCs, including[ carpets,][ textiles,][ unprimed gypsum wallboard,][ acoustical ceiling panels,][_____].

1.5 SUBMITTALS

NOTE: Revi ew Submi t t al Descr i pt i on ( SD) def i ni t i ons i n Sect i on 01 33 00 SUBMI TTAL PROCEDURES and edi t t he f ol l owi ng l i s t , and cor r espondi ng submi t t al i t ems i n t he t ext , t o r ef l ect onl y t he submi t t al s r equi r ed f or t he pr oj ect . The Gui de Speci f i cat i on t echni cal edi t or s have cl assi f i ed t hose i t ems t hat r equi r e Gover nment appr oval , due t o t hei r compl exi t y or cr i t i cal i t y, wi t h a " G. " Gener al l y, ot her submi t t al i t ems can be r evi ewed by t he Cont r act or ' s Qual i t y Cont r ol Syst em. Onl y add a " G" t o an i t em i f t he submi t t al i s suf f i c i ent l y i mpor t ant or compl ex i n cont ext of t he pr oj ect .

For Ar my pr oj ect s, f i l l i n t he empt y br acket s f ol l owi ng t he " G" c l assi f i cat i on, wi t h a code of up t o t hr ee char act er s t o i ndi cat e t he appr ovi ng aut hor i t y. Codes f or Ar my pr oj ect s usi ng t he Resi dent Management Syst em ( RMS) ar e: " AE" f or Ar chi t ect - Engi neer ; " DO" f or Di st r i ct Of f i ce ( Engi neer i ng Di v i s i on or ot her or gani zat i on i n t he Di st r i ct Of f i ce) ; " AO" f or Ar ea Of f i ce; " RO" f or Resi dent Of f i ce; and " PO" f or Pr oj ect Of f i ce. Codes f ol l owi ng t he " G" t ypi cal l y ar e not used f or Navy, Ai r For ce, and NASA pr oj ect s.

The " S" c l assi f i cat i on i ndi cat es submi t t al s r equi r ed as pr oof of compl i ance f or sust ai nabi l i t y Gui di ng Pr i nci pl es Val i dat i on or Thi r d Par t y Cer t i f i cat i on and as descr i bed i n Sect i on 01 33 00 SUBMI TTAL

PROCEDURES.

Choose t he f i r st br acket ed i t em f or Navy, Ai r For ce, and NASA pr oj ect s, or choose t he second br acket ed i t em f or Ar my pr oj ect s.

Government approval is required for submittals with a "G" or "S" classification. Submittals not having a "G" or "S" classification are [for Contractor Quality Control approval.][for information only. When used, a code following the "G" classification identifies the office that will review the submittal for the Government.] Submit the following in accordance with Section 01 33 00 SUBMITTAL PROCEDURES:

SECTION 09 90 00 Page 18

Samples of specified materials may be taken and tested for compliance with specification requirements.

SD-02 Shop Drawings

Piping Identification

SD-03 Product Data

Coating ; G[, [_____]]

Product Data Sheets

Sealant

SD-04 Samples

Color ; G[, [_____]]

Textured Wall Coating System ; G[, [_____]]

[ Sample Textured Wall Coating System Mock-Up ; G[, [_____]]

] SD-07 Certificates

Qualification Testing laboratory for coatings; G[, [_____]]

Indoor Air Quality for Paints and Primers

[ Indoor Air Quality for Consolidated Latex Paints

] SD-08 Manufacturer's Instructions

Application Instructions

Mixing

Manufacturer's Safety Data Sheets

SD-10 Operation and Maintenance Data

Coatings , Data Package 1; G[, [_____]]

1.6 QUALITY ASSURANCE

1.6.1 Regulatory Requirements

1.6.1.1 Environmental Protection

In addition to requirements specified elsewhere for environmental protection, provide coating materials that conform to the restrictions of the local Air Pollution Control District and regional jurisdiction.

Notify Contracting Officer of any paint specified herein which fails to conform.

1.6.1.2 Lead Content

Do not use coatings having a lead content over 0.06 percent by weight of

SECTION 09 90 00 Page 19 nonvolatile content.

1.6.1.3 Chromate Content

Do not use coatings containing zinc-chromate or strontium-chromate.

1.6.1.4 Asbestos Content

Provide asbestos-free materials.

1.6.1.5 Mercury Content

Provide materials free of mercury or mercury compounds.

1.6.1.6 Silica

Provide abrasive blast media containing no free crystalline silica.

1.6.1.7 Human Carcinogens

Provide materials that do not contain ACGIH 0100 confirmed human carcinogens (A1) or suspected human carcinogens (A2).

1.6.1.8 Carbon Based Fibers / Tubes

Materials must not contain carbon based fibers such as carbon nanotubes or carbon nanofibers. Intelligence Bulletin 65 ranks toxicity of carbon nanotubes on a par with asbestos.

NOTE: Sel ect onl y one of t he f ol l owi ng t wo br acket ed par agr aphs.

[ 1.6.2 Coating Contractor's Qualification

NOTE: When usi ng t he Cont r act or qual i f i cat i on c l ause r at her t han t he SSPC Cer t i f i cat i on r equi r ement s, edi t t o r equi r e appr opr i at e exper i ence.

NOTE: I nser t st r uct ur e t ype compar abl e t o t hose bei ng pai nt ed i n br acket s.

Submit the name, address, telephone number, and e-mail address of the Contractor that will be performing all surface preparation and coating application. Submit evidence that key personnel have successfully performed surface preparation and application of coatings on [_____] on a minimum of three similar projects within the past three years. List information by individual and include the following:

a. Name of individual and proposed position for this work.

b. Information about each previous assignment including:

Position or responsibility

SECTION 09 90 00 Page 20

Employer (if other than the Contractor)

Name of facility owner

Mailing address and telephone number of facility owner

Name of individual in facility owner's organization who can be contacted as a reference

Location, size and description of structure

Dates work was carried out

Description of work carried out on structure

][ 1.6.3 SSPC QP 1 Certification

NOTE: For pr oj ect s i n cont i nent al U. S. , Hawai i , Al aska, and Puer t o Ri co, r equi r e SSPC Cer t i f i cat i on. Use i n ot her l ocat i ons wher e qual i f i ed U. S. Cont r act or i s desi r ed. I f pr oj ect i nvol ves r emoval of pai nt cont ai ni ng hazar dous mat er i al s, add r equi r ement f or SSPC QP 2 cer t i f i cat i on i n sect i on of speci f i cat i on wher e t he hazar dous pai nt r emoval i s speci f i ed, gener al l y Section 02 83 00 LEAD REMEDI ATI ON.

NOTE: * * WARNI NG* * WARNI NG* * WARNI NG* * WARNI NG* *

Sol i c i t at i ons r equi r i ng SSPC Cer t i f i cat i on must poi nt out t he exi st ence and l ocat i on of t he cer t i f i cat i on r equi r ement , i n t he Pr oj ect I nf or mat i on For m. To be enf or ceabl e, i ncl ude t he r equi r ement i n t he sol i c i t at i on document s. SSPC Cer t i f i cat i on i s a speci al r esponsi bi l i t y r equi r ement pur suant t o FAR 9. 104- 2 Speci al St andar ds. Thi s i s anal ogous t o r equi r i ng bi dder s t o have a speci f i ed l evel of exper i ence or exper t i se and GAO has sust ai ned t hese t ypes of speci al requirements.

NOTE: Use br acket opt i on bel ow concer ni ng SSPC QP 1 onl y when i ndust r i al coat i ngs ar e r equi r ed.

Pai nt i ng qual i f i cat i ons f or pr oj ect s such as BEQ' s, t r ai ni ng f aci l i t i es and gener al admi ni st r at i on bui l di ngs do not r equi r e QP 1 cer t i f i cat i on.

Contractors that perform surface preparation or coating application on steel substrates must be certified by the Society for Protective Coatings (formerly Steel Structures Painting Council) (SSPC) to the requirements of SSPC QP 1 prior to Contract award, and must remain certified while accomplishing any surface preparation or coating application. If a Contractor's certification expires, the firm will not be allowed to

SECTION 09 90 00 Page 21 perform any work until the certification is reissued. Requests for extension of time for any delay to the completion of the project due to an inactive certification will not be considered. Notify the Contracting Officer of any change in Contractor certification status. Notify the Contracting Officer of all scheduled and unannounced on-site audits from SSPC and furnish a copy of all audit reports.

] 1.6.4 Approved Products List

The current MPI, "Approved Product List" which lists paint by brand, label, product name and product code as of the date of Contract award, will be used to determine compliance with the submittal requirements of this specification. The Contractor may choose to use a subsequent MPI "Approved Product List", however, only one list may be used for the entire Contract and each coating system is to be from a single manufacturer.

Provide all coats on a particular substrate from a single manufacturer.

No variation from the MPI Approved Products List is acceptable.

1.6.5 Paints and Coatings Indoor Air Quality Certifications

NOTE: The Gover nment s ' s pr ef er ence i s f or use of pr oduct s t hat have been cer t i f i ed f or i ndoor ai r qual i t y by a t hi r d- par t y or gani zat i on such as MPI ' s MPI GPS- 1- 14 and MPI GPS- 2- 14 Gr een Per f or mance St andar ds. Resear ch has shown t hat al l pai nt s except consol i dat ed l at ex pai nt s ar e avai l abl e among t hr ee nat i onal manuf act ur er s. Ver i f y t her e i s a cer t i f i ed pr oduct avai l abl e when speci f y i ng consol i dat ed l at ex pai nt t hat i s bot h cost ef f ect i ve and appr opr i at e f or t he pr oj ect . Conf i r m l ocal / r egi onal avai l abi l i t y of cer t i f i ed pr oduct s when speci f y i ng consol i dat ed l at ex pai nt t hat does not i mpact cost ef f ect i veness.

Provide paint and coating products certified to meet indoor air quality requirements by MPI GPS-1-14 , MPI GPS-2-14 or provide certification by other third-party programs. Provide current product certification documentation from certification body.

Provide certification of Indoor Air Quality for Paints and Primers .

[Provide certification of Indoor Air Quality for Consolidated Latex Paints .

]Submit required indoor air quality certifications in one submittal package.

1.6.6 Field Samples and Tests

The Contracting Officer may choose up to two coatings that have been delivered to the site to be tested at no cost to the Government. Take samples of each chosen product as specified in the paragraph SAMPLING PROCEDURE. Test each chosen product as specified in the paragraph TESTING PROCEDURE. Remove products from the job site which do not conform, and replace with new products that conform to the referenced specification.

Test replacement products that failed initial testing as specified in the paragraph TESTING PROCEDURE at no cost to the Government.

NOTE: The f ol l owi ng par agr aph i s t ai l or ed f or

SECTION 09 90 00 Page 22 i ncl usi on i n ARMY pr oj ect s onl y.

Onl y r equi r e t he t est i ng f or l ar ge quant i t i es of epoxy/ pol yur et hane coat i ngs or a s i ngl e coat i ng syst em t hat i s used i n l ar ge quant i t i es on t he pr oj ect . A l ar ge quant i t y of epoxy/ pol yur et hane coat i ngs i s consi der ed t o be 189 Li t er s 50 gal l ons or mor e, a l ar ge quant i t y of ot her coat i ng syst ems i s consi der ed t o be 757 Li t er s 200 gal l ons or mor e.

Li st al l coat i ngs f or t est i ng by MPI or SSPC pai nt number i n t he f ol l owi ng par agr aph.

[ Another required testing is Batch Quality Conformance Testing to prove conformance of the manufacturer's paint to the specified MPI standard.

This testing is accomplished before the materials are delivered to the job site. Provide testing for [_____] paint products. Test paint products as specified in the paragraph TESTING PROCEDURE.

1.6.6.1 Sampling Procedure

Select paint at random from the products that have been delivered to the job site for sample testing. The Contractor must provide one liter one quart samples of the selected paint materials. Take samples in the presence of the Contracting Officer, and label, and identify each sample.

Provide labels in accordance with the paragraph PACKAGING, LABELING, AND

STORAGE.

1.6.6.2 Testing Procedure

Provide Batch Quality Conformance Testing for specified products, as defined by and performed by MPI. As an alternative to Batch Quality Conformance Testing, the Contractor may provide Qualification Testing for specified products above to the appropriate MPI product specification, using the third-party laboratory approved under the paragraph QUALIFICATION TESTING laboratory for coatings. Include the backup data and summary of the test results within the qualification testing lab report. Provide a summary listing of all the reference specification requirements and the result of each test. Clearly indicate in the summary whether the tested paint meets each test requirement. Note that Qualification Testing may take 4 to 6 weeks to perform, due to the extent of testing required.

Submit name, address, telephone number, FAX number, and e-mail address of the independent third party laboratory selected to perform testing of coating samples for compliance with specification requirements. Submit documentation that laboratory is regularly engaged in testing of paint samples for conformance with specifications, and that employees performing testing are qualified. If MPI is chosen to perform the Batch Quality Conformance testing, the above submittal information is not required, only a letter is required from the Contractor stating that MPI will perform the testing.

1.6.7 Textured Wall Coating System

Three complete samples of each indicated type, pattern, and color of textured wall coating system applied to a panel of the same material as that on which the coating system will be applied in the work. Provide samples of wall coating systems minimum 125 by 175 mm 5 by 7 inches and of

SECTION 09 90 00 Page 23 sufficient size to show pattern repeat and texture.

[ 1.6.8 Sample Textured Wall Coating System Mock-Up

NOTE: I ncl ude t he f ol l owi ng Mock- Up sect i on when a t ext ur ed wal l coat i ng syst em i s i ncl uded i n t he project.

After coating samples are approved and prior to starting installation, provide a minimum 2.43 m by 2.43 m 8 foot by 8 foot mock-up for each substrate and for each color and type of textured wall coating using the actual substrate materials. Use the approved mock-up samples as a standard of workmanship for installation within the facility. Submit at least 48 hour advance written notice to the Contracting Officer's Representative prior to mock-up installation.

] 1.7 PACKAGING, LABELING, AND STORAGE

NOTE: The f ol l owi ng par agr aph i ncl udes t ai l or i ng f or i ncl usi on i n Navy pr oj ect s. I ncl ude t he l ast t wo sent ences f or Navy pr oj ect s onl y.

Mat er i al s wi t h a hi gh capaci t y t o absor b VOC emi ssi ons i ncl ude mat er i al s whi ch ar e woven, f i br ous or por ous i n nat ur e, such as acoust i cal cei l i ngs, car pet , and t ext i l es. I ncl ude such mat er i al s bei ng i nst al l ed i n br acket s.

Provide paints in sealed containers that legibly show the Contract specification number, designation name, formula or specification number, batch number, color, quantity, date of manufacture, manufacturer's formulation number, manufacturer's directions including any warnings and special precautions, and name and address of manufacturer. Furnish pigmented paints in containers not larger than 20 liters 5 gallons . Store paints and thinners in accordance with the manufacturer's written directions, and as a minimum, stored off the ground, under cover, with sufficient ventilation to prevent the buildup of flammable vapors, and at temperatures between 4 to 35 degrees C 40 to 95 degrees F . Do not store paint, polyurethane, varnish, or wood stain products with materials that have a high capacity to absorb VOC emissions[, including [_____]]. Do not store paint, polyurethane, varnish, or wood stain products in occupied spaces.

1.8 SAFETY AND HEALTH

Comply with applicable Federal, State, and local laws and regulations, and with the ACCIDENT PREVENTION PLAN, including the Activity Hazard Analysis as specified in Section 01 35 26 GOVERNMENTAL SAFETY REQUIREMENTS and in Appendix A of EM 385-1-1 . Include in the Activity Hazard Analysis the potential impact of painting operations on painting personnel and on others involved in and adjacent to the work zone.

1.8.1 Toxic Materials

To protect personnel from overexposure to toxic materials, conform to the

SECTION 09 90 00 Page 24 most stringent guidance of:

a. The applicable manufacturer's Safety Data Sheets (SDS) or local regulation.

b. 29 CFR 1910.1000 .

c. ACGIH 0100 , threshold limit values.

NOTE: Del et e f ol l owi ng par agr aph i f no l ead i s cont ai ned i n exi st i ng coat i ng syst ems.

[ d. The appropriate OSHA standard in 29 CFR 1910.1025 and 29 CFR 1926.62 for surface preparation on painted surfaces containing lead. Removal and disposal of coatings which contain lead is specified in Section 02 83 00 LEAD REMEDIATION. Additional guidance is given in SSPC Guide 6 and SSPC Guide 7 . Refer to drawings for list of hazardous materials located on this project. Coordinate paint preparation activities with this specification section.

NOTE: Del et e f ol l owi ng par agr aph i f no asbest os i s cont ai ned i n exi st i ng coat i ng syst ems.

[ e. The appropriate OSHA standards in 29 CFR 1910.1001 for surface preparation of painted surfaces containing asbestos. Removal and disposal of coatings which contain asbestos materials is specified in Section 02 82 00 ASBESTOS REMEDIATION. Refer to drawings for list of hazardous materials located on this project. Coordinate paint preparation activities with this specification section.

] Submit manufacturer's Safety Data Sheets for coatings, solvents, and other potentially hazardous materials, as defined in FED-STD-313 .

1.9 ENVIRONMENTAL REQUIREMENTS

NOTE: Choose br acket ed opt i on i n t he f ol l owi ng par agr aph i f hi gh emi ssi on pai nt s or coat i ngs, such as epoxi es or al kyds, wi l l be used.

Comply, at minimum, with manufacturer recommendations for space ventilation during and after installation.[ Isolate area of application from rest of building when applying high-emission paints or coatings.]

1.9.1 Coatings

Do not apply coating when air or substrate conditions are:

a. Less than 3 degrees C 5 degrees F above dew point;

b. Below 10 degrees C 50 degrees F or over 35 degrees C 95 degrees F , unless specifically pre-approved by the Contracting Officer and the product manufacturer. Do not, under any circumstances, violate the manufacturer's application recommendations.

SECTION 09 90 00 Page 25

1.9.2 Post-Application

NOTE: The f ol l owi ng par agr aphs ar e t ai l or ed f or i ncl usi on i n NAVY pr oj ect s onl y.

Choose t he most appr opr i at e opt i on( s) f or vent i l at i on. For i nst ance, hi gh- humi di t y r egi ons may gener at e t oo much condensat e when usi ng 100 per cent out si de ai r .

Vacate space for as long as possible after application. Wait a minimum of 48 hours before occupying freshly painted rooms. Maintain one of the following ventilation conditions during the curing period, or for 72 hours after application:

a. Supply 100 percent outside air 24 hours a day.

b. Supply airflow at a rate of 6 air changes per hour, when outside temperatures are between 13 degrees C 55 degrees F and 29 degrees C 85 degrees F and humidity is between 30 percent and 60 percent.

c. Supply airflow at a rate of 1.5 air changes per hour, when outside air conditions are not within the range stipulated above.

PART 2 PRODUCTS

2.1 MATERIALS

NOTE: Repr ocessed and consol i dat ed l at ex pai nt s ar e EPA desi gnat ed pr oduct s. Ver i f y t he avai l abi l i t y of cer t i f i ed pr oduct s wi t hi n t he r egi on when speci f y i ng consol i dat ed l at ex pai nt .

Conform to the coating specifications and standards referenced in PART 3.

Submit Product Data Sheets for specified coatings and solvents. Provide preprinted cleaning and maintenance instructions for all coating systems.

Submit Manufacturer's Instructions on Mixing : Detailed mixing instructions, minimum and maximum application temperature and humidity, pot life, and curing and drying times between coats.

[ 2.2 COLOR CODING FOR SHORE-TO SHIP UTILITY CONNECTIONS

NOTE: I ncl ude t he f ol l owi ng br acket ed par agr aph and Tabl e i f t he pr oj ect i ncl udes pai nt i ng of Shor e- To- Shi p Ut i l i t y connect i ons

Color Coding For Shore-To-Ship Utility Connections: Paint hose connection fittings and shut-off valves the designated color. In addition to color coding provide 50 mm 2 inch high stenciled letters using black stencil paint, clearly designating service for each connection.

SECTION 09 90 00 Page 26

Color Coding for Shore-to-Ship

Utility Connections

Service Color SAE AMS-STD-595A No.

Potable Water* Blue 15044

Water Provided for Fire Protection**

Red 11105

Chilled Water Striped Blue/White 15044 / 17886

Oily Waste Water Striped Yellow/Black 13528 / 17038

Sewer Gold 17043

Steam White 17886

High Pressure Air Gray 16081

Low Pressure Air Tan 10324

Fuels Yellow 13655

* This includes connections serving domestic functions.

** This includes non-potable salt water or, at some locations, fresh water connections provided for fire protection (may also include flushing and cooling requirements). Note: This does not include waterfront fire hydrants.

] 2.3 COLOR SELECTION OF FINISH COATS

Provide colors of finish coats as indicated or specified. Allow Contracting Officer to select colors not indicated or specified.

Manufacturers' names and color identification are used for the purpose of color identification only. Named products are acceptable for use only if they conform to specified requirements.