PART 6 ATTACHMENT A1_19-0037 Building 1 A110 Revised.pdf

DEMOLISH EXISTING ROOF

SCUTTLE. REPLACE WITH NEW

INSULATED ROOF SCUTTLE AND

FRAME WITH NEOPRENE SEAL ALL

SIDES. PROVIDE HINGED

CONDITION AND HASP FOR

PADLOCK (NIC)

SEE NOTE CUPOLA GENERAL

NOTES

SEE NOTES N1, N3, AND N4

FROM LEFT TO RIGHT:

1. SYNTHETIC PERMEABLE ICE &

SHIELD MEMBRANE (PERM 10

OR HIGHER)

2. FLASHING

3. CAP FLASHING

FROM BOTTOM TO TOP:

1. CLOSED CELL SPRAYED ON

INSULATION

2. SUBSTRATE

3. SYNTHETIC PERMEABLE ICE &

SHIELD MEMBRANE (PERM 10 OR

HIGHER)

4. SSMR

1. SSMR CLOSURE STRIP

VAPOR BARRIER OVERLAPED OVER

FLASHING

DEMOLISH TRIM AND REMOVE FRONT

PANEL/CLADDING AS NECESSARY TO ALLOW

THE REMOVAL OF THE LOUVER

EXIST LOUVER: REMOVE, REPAIR AND

PREPARE FOR RE-FINISH STORE FOR

RE-INSTALLATION. DISCARD IF DAMAGED

FLASHING: DEMO

DEMOLISH TRIM AND REMOVE FRONT

PANEL/CLDDING AS NECESSARY TO ALLOW THE

REMOVAL OF THE LOUVER

EXIST LOUVER: REMOVE, REPAIR AND PREPARE

FOR RE-FINISH STORE FOR RE-INSTALLATION.

DISCARD IF DAMAGED

INSTALL NEW THROUGH FLASHING. INSTALL

PANEL/CLADDING AND TRIM TO MATCH

LOUVER: RE-INSTALL, PAINT. REPLACE WITH

NEW TO MATCH EXISTING IF DAMAGED

1' ALUMINUM INSULATED PANEL OVER THE

ENTIRE LOUVER OPENING. INSTALL OVER

CONTINUOUS BEAD OF CAULKING AND FASTEN

AT 6" O.C. ALL SIDES. TYP AT ALL LOUVERS

INSTALL NEW VAPOR BARRIER AS NECESARY

INSTALL NEW THROUGH FLASHING. INSTALL

PANEL AND TRIM TO MATCH. PAINT

LOUVER: RE-INSTALL, PAINT. REPLACE WITH NEW

TO MATCH EXISTING IF DAMAGED

INSULATED PANEL SEE DETAIL

ABOVE

INSTALL NEW VAPOR BARRIER AS NECESARY

DEMOLISH TRIM AND REMOVE FRONT PANEL/AS

NECESSARY AS NECESSARY TO ALLOW THE

REMOVAL OF THE LOUVER

EXIST LOUVER: REMOVE, REPAIR AND PREPARE

FOR RE-FINISH STORE FOR RE-INSTALLATION.

DISCARD IF DAMAGED

INSTALL NEW THROUGH FLASHING. INSTALL

PANEL/CLADDING AND TRIM TO MATCH

LOUVER: RE-INSTALL, PAINT. REPLACE WITH

NEW TO MATCH EXISTING IF DAMAGED

INSTALL NEW VAPOR BARRIER AS NECESARY

INSULATED PANEL SEE DETAIL

ABOVE

BLDG. 1 CUPOLA ELEVATION1

CUPOLA BASE AT SSMR- RENO6

CONST. CONTR. NO.

DISCLOSURE OF INFORMATION CONTRACTOR SHALL COMPLY AS FOLLOWS:

A. THE CONTRACTOR SHALL NOT RELEASE TO ANYONE OUTSIDE THE CONTRACTOR'S

ORGANIZATION ANY UNCLASSIFIED INFORMATION, REGARDLESS OF MEDIUM (E.G., FILM, TAPE, DOCUMENT), PERTAINING TO ANY PART OF THIS CONTRACT OR ANY PROGRAM RELATED TO

THIS CON- TRACT OR ANY PROGRAM RELATED TO THIS CONTRACT, UNLESS:

(1) THE CONTRACTING OFFICER HAS GIVEN PRIOR WRITTEN APPROVAL; OR

(2) THE INFORMATION IS OTHERWISE IN THE PUBLIC DOMAIN BEFORE THE

DATE OF RELEASE.

B. REQUESTS FOR APPROVAL SHALL IDENTIFY THE SPECIFIC INFORMATION TO BE RELEASED, THE

MEDIUM TO BE USED, AND THE PURPOSE FOR THE RELEASE. THE CONTRACTOR SHALL SUBMIT

ITS REQUEST TO THE CONTRACTING OFFICER AT LEAST 45 DAYS BEFORE THE PROPOSED DATE

FOR RELEASE.

C. THE CONTRACTOR AGREES TO INCLUDE A SIMILAR REQUIREMENT IN EACH SUBCONTRACT

UNDER THIS CONTRACT. SUBCONTRACTORS SHALL SUBMIT REQUESTS FOR AUTHORIZATION

TO RELEASE THROUGH THE PRIME CONTRACTOR TO THE CONTRACTING OFFICER.

17 APRIL 2020 A110

GUSTAVO DE LUCA

GUSTAVO DE LUCA

GUSTAVO DE LUCA

GUSTAVO DE LUCA

THOMAS BURTON

PWO or OICC

BUILDING 1

CUPOLA ELEV, SEC, & DETAILS

XXXXX

19-0037

NOTED NA

10 10

ROOF EDGE & LOUVER HEAD - DEMO2

LOUVER SILL & ROOF FLASHING- DEMO4

ROOF EDGE & LOUVER HEAD- RENO3

LOUVER SILL & ROOF FLASHING - RENO5

LOUVER JAMB - DEMO7 LOUVER JAMB - RENO8

CUPOLA GENERAL NOTES

No.

NOTES (NOT KEYED IN SEC. & DET.)

N1

EXIST TRIM ITEMS, FASCIA, SOFFIT, PANELS, ETC.: FOR BIDING PURPOSES

ASSUME THAT 50% MUST BE REPLACED. ALL EXTERIOR CLADDING,

MOLDING, RIM, FASCIA BOARDS, LAP SIDING, SOFFIT MUST BE SOLID PVC

WITH A FLAME SPREAD INDEX OF LESS THAN 25, ASTM E 84.

N2

EXISTING ROOFING SUBSTRATE, NAILERS, BLOCKING, ETC.: REPLACE ALL

DAMAGED ITEMS. FOR BIDING PURPOSES ASSUME 50% NEW MATERIALS.

REPLACE WITH MOISTURE RESISTANT LUMBER, MATCH EXISTING

THICKNESS AND OTHER CONDITIONS

N3

EXISTING ROOFING MATERIAL: THE CONTRACTOR MUST VERIFY ITS

CONDITION. REPLACE WITH NEW IF NECESSARY. MATCH EXISTING

N4

APPLY CLOSED CELL SPRAY POLYURETHANE FOAM, 1” THICK TO THE

INSIDE FACE OF ALL THE CUPOLA'S COMPONENTS. APPLY TO ROOF

SUBSTRATE TO A MINIMUM OF 24" BEYOND THE CUPOLA'S OUTER EDGES

N5

EXISTING CLADDING, SIDING, ASSOCIATED TRIM, SUBSTRATE, VAPOR

BARRIER, ETC.: REMOVE AS NECESSARY TO ALLOW THE INSTALLATION OF

NEW FLASHING. REPLACE WITH NEW MOISTURE RESISTANT LUMBER AND

OTHER SUITABLE MATERIALS.

N6

EXISTING COATING AND SEALANT JOINTS: REMOVE ALL LOOSE COATING

AND JOINT SEALANTS. RE-FASTEN JOINTS AS NECESSARY. THE

CONTRACTOR MUST VERIFY FIELD THESE CONDITION. RE-COAT AND

RE-SEAL ALL CUPOLA, THE DESIGNER OF RECORD MUST PROVIDE

RECOMMENDATION AS TO THE TYPE OF MATERIAL BEST SUITED FOR THIS

APPLICATION

AutoCAD SHX Text NOTES: 1. THE CONTRACTOR MUST FIELD VERIFY ALL THE CONDITIONS SHOWN. THESE DETAILS THE CONTRACTOR MUST FIELD VERIFY ALL THE CONDITIONS SHOWN. THESE DETAILS AND RECOMMENDATIONS MUST NOT BE CONSIDERED THE FINAL DESIGN. IT IS THE CONTRACTORS RESPONSIBILITY TO REPRESENT THE SCOPE OF WORK IN SUFFICIENT DETAILS IN THE SHOP DRAWINGS, INCLUDING BUT NOT LIMITED TO ACTUAL DETAILS, MATERIALS SPECIFICATIONS, METHODS FOR REMOVAL AND REPLACEMENT WHILE MAINTAINING THE INTEGRITY OF THE BUILDING ENVELOPE, COLOR SELECTIONS FOR APPROVAL BY THE BEAP-REVIEW BOARD, ETC. 2. THESE BUILDINGS ARE REGISTERED HISTORICAL LANDMARKS. THE CONTRACTOR MUST THESE BUILDINGS ARE REGISTERED HISTORICAL LANDMARKS. THE CONTRACTOR MUST PRESENT THE PROPOSED SOLUTION(S) IN THE SHOP DRAWING SUBMITTAL OR WITH ANY OTHER METHOD SELECTED LEFT TO THE CONTRACTOR'S PREROGATIVE (FOR EXAMPLE: MOCK UPS, FIELD MEETINGS, ETC.) TO ENSURE THAT IT IS CONSISTENT WITH THE DESIGN INTENT OF THE MCBCL 3. ALL ENLARGED DETAILS SHOWN MAY HAVE SMALL VARIATIONS AMONG THE VARIOUS ALL ENLARGED DETAILS SHOWN MAY HAVE SMALL VARIATIONS AMONG THE VARIOUS CUPOLAS DESIGNS AND DETAILING. THESE DETAILS ARE NOT AN ACCURATE REPRESENTATION OF THE ACTUAL FIELD CONDITIONS. THE CONTRACTOR MUST BRING TO THE ATTENTION OF THE CM ANY DISCREPANCY FOUND IN THE FIELD. THE CONTRACTOR MUST PRESENT ALTERNATIVE DETAILING TO ACCOMMODATE THE EXISTING CONDITIONS.

AutoCAD SHX Text

AutoCAD SHX Text A107

AutoCAD SHX Text ALL DIMENSIONS SHOWN ARE FROM EXISTING DRAWINGS AND HAVE NOT BEEN VERIFIED. FIELD CHECK

AutoCAD SHX Text

AutoCAD SHX Text A107

AutoCAD SHX Text

AutoCAD SHX Text A107

AutoCAD SHX Text

AutoCAD SHX Text A107

AutoCAD SHX Text

AutoCAD SHX Text A107

AutoCAD SHX Text

AutoCAD SHX Text A107

AutoCAD SHX Text

AutoCAD SHX Text A107

AutoCAD SHX Text NOTES: 1. THE DESIGNER OF RECORD MUST FIELD VERIFY ALL THE CONDITIONS SHOWN. THESE DETAILS AND RECOMMENDATIONS MUST NOT BE CONSIDERED THE FINAL DESIGN. IT IS THE DESIGNER OF RECORD RESPONSIBILITY TO REPRESENT THE SCOPE OF WORK IN THE DESIGNER OF RECORD MUST FIELD VERIFY ALL THE CONDITIONS SHOWN. THESE DETAILS AND RECOMMENDATIONS MUST NOT BE CONSIDERED THE FINAL DESIGN. IT IS THE DESIGNER OF RECORD RESPONSIBILITY TO REPRESENT THE SCOPE OF WORK IN SUFFICIENT DETAILS IN THE DRAWINGS AND TO DESCRIBE IT IN SUFFICIENT DETAIL IN THE SPECIFICATIONS. THE SECTIONS AND DETAILS ARE GENERIC IN NATURE AND NOT THE FINAL CONFIGURATION. THE DESIGNER OF RECORD MUST PERFORM THE APPROPRIATE CALCULATIONS TO DETERMINE APPROPRIATE MATERIALS, LOADS, CODE COMPLIANCE REQUIREMENTS, ETC. 2. THE DESIGNER OF RECORD MUST PRESENT THE PROPOSED SOLUTION(S) DURING THE CDW TO ENSURE THAT IT IS CONSISTENT WITH THE DESIGN INTENT OF THE MCBCL THE DESIGNER OF RECORD MUST PRESENT THE PROPOSED SOLUTION(S) DURING THE CDW TO ENSURE THAT IT IS CONSISTENT WITH THE DESIGN INTENT OF THE MCBCL 3. THE DESIGNER OF RECORD MUST PERFORM THE APPROPRIATE CODE COMPLIANCE ANALYSIS BASED ON OCCUPANCY TO DETERMINE THE MINIMUM NUMBER OF REQUIRED PLUMBING FIXTURES, REQUIRED EXITS, ETC. ALL THE FLOOR PLAN LAYOUTS MUST BE THE DESIGNER OF RECORD MUST PERFORM THE APPROPRIATE CODE COMPLIANCE ANALYSIS BASED ON OCCUPANCY TO DETERMINE THE MINIMUM NUMBER OF REQUIRED PLUMBING FIXTURES, REQUIRED EXITS, ETC. ALL THE FLOOR PLAN LAYOUTS MUST BE APPROVED BY THE USER AT THE CDW. THIS APPLIES TO: THE SCOPE OF WORK (SOW) SHOWN WITHIN BLOCKED AREAS ON THE DRAWINGS DEVELOPED FLOOR PLAN LAYOUTS SHOWING FOR EXAMPLE: TOILET FIXTURES, FURNITURE, CABINETS, EXITS, ETC. ARE GENERIC IN NATURE AND NOT THE FINAL CONFIGURATION 4. NOTES SHOWN WITH TYPICAL (TYP) INDICATES CONDITIONS THAT OCCUR MULTIPLE TIMES NOTES SHOWN WITH TYPICAL (TYP) INDICATES CONDITIONS THAT OCCUR MULTIPLE TIMES 5. COMPLETE DEMOLITION OF INTERIOR CONDITIONS INCLUDES: WOOD OR METAL STUDS OR OTHER MATERIALS, GWB, PLASTER, FURRING FRAMING, FLOORING, BASE, CEILING, PLUMBING, HVAC, ELECTRICAL, SPRINKLER SYSTEMS, ETC. COMPLETE DEMOLITION OF INTERIOR CONDITIONS INCLUDES: WOOD OR METAL STUDS OR OTHER MATERIALS, GWB, PLASTER, FURRING FRAMING, FLOORING, BASE, CEILING, PLUMBING, HVAC, ELECTRICAL, SPRINKLER SYSTEMS, ETC. 6. THE BUILDINGS IN THIS PROJECT ARE HISTORICAL STRUCTURES. ALL EXTERIOR NEW EXTERIOR ITEMS MUST MATCH EXISTING DESIGN AESTHETICS. THE DESIGNER OF RECORD MUST SUBMIT DESIGN INTENT TO BE REVIEWED DURING THE CDW-PHASE THE BUILDINGS IN THIS PROJECT ARE HISTORICAL STRUCTURES. ALL EXTERIOR NEW EXTERIOR ITEMS MUST MATCH EXISTING DESIGN AESTHETICS. THE DESIGNER OF RECORD MUST SUBMIT DESIGN INTENT TO BE REVIEWED DURING THE CDW-PHASE 7. THE ASHRAE 90.1 -2016 REQUIREMENTS SHOWN IN SKEET A100 ARE APPLICABLE TO ALL THE BUILDINGS INCLUDED IN THIS PROJECTTHE ASHRAE 90.1 -2016 REQUIREMENTS SHOWN IN SKEET A100 ARE APPLICABLE TO ALL THE BUILDINGS INCLUDED IN THIS PROJECT

AutoCAD SHX Text

NTS

AutoCAD SHX Text A110

AutoCAD SHX Text 3"'= 1'-0"

AutoCAD SHX Text A110

AutoCAD SHX Text

SHEET:

AutoCAD SHX Text 80091

AutoCAD SHX Text E1

AutoCAD SHX Text

MARINE CORPS BASE

AutoCAD SHX Text

DEPARTMENT OF THE NAVY NAVAL FACILITIES ENGINEERING COMMAND

AutoCAD SHX Text

CAMP LEJEUNE, NORTH CAROLINA

AutoCAD SHX Text

DESIGN DIR.

AutoCAD SHX Text

SUBMITTED BY:

AutoCAD SHX Text

NAVFAC DRAWING NO.

AutoCAD SHX Text

CODE IDENT. NO

AutoCAD SHX Text

SIZE

AutoCAD SHX Text

SPEC.

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

SATISFACTORY TO:

AutoCAD SHX Text

APPROVED: PWO OR OICC:

AutoCAD SHX Text

DR.

AutoCAD SHX Text

DES.

AutoCAD SHX Text

CHK.

AutoCAD SHX Text

DATE:

AutoCAD SHX Text

DATE:

AutoCAD SHX Text

OF

AutoCAD SHX Text 3"'= 1'-0"

AutoCAD SHX Text A110

AutoCAD SHX Text 3"'= 1'-0"

AutoCAD SHX Text A110

AutoCAD SHX Text 3"'= 1'-0"

AutoCAD SHX Text A110

AutoCAD SHX Text 3"'= 1'-0"

AutoCAD SHX Text A110

AutoCAD SHX Text 3"'= 1'-0"

AutoCAD SHX Text A110

AutoCAD SHX Text 3"'= 1'-0"

AutoCAD SHX Text A110