Navy Paint Drawing.pdf

16 15 14 13 12 Li

GENERAL NOTES

H 1, FOR ALL BARE METAL, UNPAINTED AREAS’ DO NOT APPLY DECORATIVE

PAINT IN THIS AREA,

G

2. APPLY 1’ WIDE STRIPE OF CLEAR ENAMEL CENTERED OVER

LEADING EDGE OF PAINT.

3. BLUE STRIPE MEASUREMENT IS AS FOLLOWS 3’ BOTTOM OF WINDOW

BARE METAL FRAME TO TOP OF BLUE STRIPE.

11. ALL EXPOSED PRIMED SURFACES: BELOW GOLD STRIPE SHALL

RECEIVE’ COLOR *16440 LIGHT GREYj ABOVE INSIGNIA BLUE

STRIPE SHALL RECEIVE: COLOR #17875 INSIGNIA WHITE

WITH THE EXCEPTION OF THE ANTI—GLARE AREA.

12, ALL DECALS SHALL BE APPLIED PER NAO1—C9B—2—11.

13. DIMENSIONING AND TOLERANCING PER ASME Y14, 5M—A994.

THIS DRAWING HAS BEEN GENERATED AND IS MAINTAINED

BY A CAD SYSTEM. CHANGES SHAU. BE INCORPORATED AS

DIRECTED BY THE DESIGN AC11VITY.

E

4. LETTERING TO BE PER MILITARY SPECIFICATION MIL—STD—2161 (AS).

5. COLOR USED ARE IDENTIFIED BY THE FOLLOWING NUMBERS:

COLOR FED STD 595 MIL

FLAT BLACK 37038 MIL—PRF—83285

GLOSS BLACK 17038 MIL—PRF—83285

INSIGNIA BLUE 15044 MIL—PRF—83285

LIGHT GREY 16440 MIL—PRF—83285

GOLD 17043 MIL—PRF—83285

INSIGNIA WHITE 17875 MIL—PRF—83285

RED 11136 MIL—PRF—83285

PRIMER MIL—PRF—23377

CLEAR MIL—PRF—83285

6. C—9 AIRCRAFT EMPLOY A COPPER BERYLLIUM ALLOY IN THE MAIN

LANDING GEAR DOORS SKIDS. THESE MAY BE SUBJECT TO SANDING IN

PREPARATION FOR PAINTING THAT MAY CONSTITUTE A HEALTH RISK IF

PROPER PRECAUTIONS ARE NOT TAKEN. ENSURE PROPER PRECAUTIONS

ARE TAKEN WHEN SANDING THE DOOR SKIDS,

7. AREAS TO BE PAINTED SHALL BE PREPARED AND PAINTED PER

D APPROPRIATE MILITARY SPEC DOCUMENTS.

8. APPLICATION AND REMOVAL OF TEMPORARY CORROSION PROTECTION

SHALL BE ACCOMPLISHED PER MILITARY SPEC DOCUMENTS.

9. SPLINE ALL CURVES APPROXIMATELY AS SHOWN.

14. ALL DIMENSIONS ARE ALONG CONTOUR, EXCEPT AS NOTED.

15. UNLESS NOTED, ALL DIMENSIONS ARE IN INCHES,

16. DO NOT PAINT RUBBER, MYLAR, SILICONE RUBBER SEALANT,

OR RUBBER STRIPS,

17. ANTENNAS: DO NOT PAINT BLADE ANTENNAS, OR FLUSH MOUNTED

ANTENNAS LOCATED ON TOP OR BOTTOM OF AIRCRAFT.

18, DO NOT PAINT RADOME.

19. DO NOT PAINT ANTI—CHAFE COATING ON ELEVATOR STABILIZER

ROTATION AREA.

20. MASK OVER CABIN PRESSURE SAFETY RELEASE VALVES PRIOR TO

PAINTING THE AIRCRAFT. AFTER PAINTING, INSPECT TO ENSURE

ALL MASKING HAS BEEN REMOVED.

21. ALL FUSELAGE DRAIN VALVES ALONG UNDERSIDE MUST BE

TEMPORARILY PLUGGED PRIOR TO PAINTING. PAINT THE EXPOSED

SURFACE OF THE HOUSING UNLESS IT FALLS IN A BARE METAL

AREA.

22, PASSENGER WINDOW FRAMES ARE 0. 50’ BARE METAL.

23. APPLY TEFLON COATING TO LEADING EDGE OF WINGS

BEHIND SLATS AFTER PAINTING.

C 10. ALL UNPAINTED AREA OF CLAD SKIN SHALL MEET THE REQUIREMENTS

OF APPROPRIATE DAC/BAC DOCUMENTS.

24, FORWARD FLAP HINGE COVERS SHALL

AND COVERED WITH MYLAR.

REMAIN BARE METAL

DISTRIBUTION STATEMENT C:

DISTRIBUTION AUTHORIZED TO U.S. GOVERNMENT AGENCIES ONLY AND THEIR CONTRACTORS TO PROTECT PUBUCATIONS REQUIRED FOR OFFICIAL USE OR FOR ADMINISTRATIVE OR OPERATIONAL PURPOSES ONLY, DE1ERMINED ON 1 JUNE 2010. OThER REQUESTS FOR THIS DOCUMENT SHAU. BE REFERRED TO COMMANDING OffiCER, NAVAL AIR SYSTEMS COMMAND (PMA 2O7/C—9 IPT), 46990 HINKLE CIRCLE.

BUILDING 419, PATUXENT RIVER, MD 20670—1627.

EFFECTIVE

SHEET LIST

ALL USN C—9B

EFFECTIVITY

AT

L1C*T25I

F

DESTRUCTION NOTICE:

FOR UNCLASSIFiED, LIMITED DOCUMENTS, DESTROY BY ANY METHOD THAT WILL PREVENT DISCLOSURE

OF CONTENTS OR RECONSTRUCTION OF THE DOCUMENT.

L5 It $1NYA! I t14.Efl dI1t Wtfl25, I DII IN II€

2 . .2 • XX ‘ANGIE

*25 I*.i I*.os I±a

ABBREVIATIS lAW

ASHE Y14. 3811

_n.n TIC WI

NAVAL AIR SYSTD4S I4AND

PATUXENT RIVEN, 140 20670—1627

EXTERIOR SURFACE PAINT

AND MAJOR MARKINGS —

—9B AIRCRAFT (USN)

4025AS0200

7 6

USN C-9B (Sheet 6 of 6) Doors & Escape Hatches(R1)