TE-6_Instructions_and_TO_Summary.docx

TECHNICAL EXHIBIT 6 Reference Number: Solicitation FA2860-18-R-0010

APPLICABLE AF INSTRUCTIONS AND TECHNICAL ORDERS (MANDATORY)

Publications and forms that apply to the PWS are listed below. The publications and forms have been coded as mandatory or advisory. The contractor is obligated to follow those publications and use those forms coded as mandatory to the extent specified in other sections of this PWS. The contractor shall be guided by those publications or use those forms coded advisory to the extent necessary to accomplish requirements in this PWS. The government shall provide all publications and forms in electronic or paper format (when electronic format is not available).

The following regulations, manuals, and other directives, as supplemented, are applicable to the requirements set forth in this contract. The most current referenced directives and supplements thereto are to be utilized in the pricing of this contract. If additional publications are applicable or noted in the PWS that are not listed below, they should be considered in pricing. The contractor shall be required to maintain the Technical Libraries and therefore, will be responsible for updating and utilizing changes to these directives as they occur. It is the responsibility of the contractor to establish follow-on requirements with the publication distribution office and that the most current publication or form is in use. Supplements or amendments to listed publications from any organizational level may be issued during the life of the contract. The contractor shall immediately implement those changes that result in a decrease or no change in the contract price and notify the contracting officer in writing of such change. Should a decrease in contract price result, the contractor shall provide a proposal for a reduction in the contract price to the contracting officer. Before implementing any change that will result in an increase in contract price, the contractor shall submit to the contracting officer a price proposal within 30 calendar days following receipt of the change by the contractor. The contracting officer and the contractor shall negotiate the change into the contract under the provisions of the contract clause entitled "Changes." Failure of the contractor to submit a price proposal within 30 calendar days following receipt of the change entitles the government to performance according to such change at no increase in contract price (unless the time requirement is waived by the contracting officer according to paragraph (c) of the Changes clause).The contractor shall be bound to accomplish the tasks set forth in this PWS, and the references set forth in the PWS. Should there be a conflict between or among two or more such references, those issued by a higher authority will control over those issued by a lower authority; for those issued at the same level of authority, those with a later date of issue will control over those with earlier dates of issue. Any task set forth in any such reference which will call for the exercise of non-delegable discretionary government authority will be subject to the final approval of the government official having such authority.

Technical Data

00-25-245

Testing And Inspection Procedures For Personnel Safety And Rescue Equipment

00-80G-32

00-110A-1

Guidelines For Identification And Handling Of Acft And Material Contaminated With Radioactive Debris (Fallout)

1-1-300

Acceptance/Functional Check Flight and Maintenance OPR Checks

1-1A-1

General Manual For Structural Repair Engineering, H/ B Series For Aircraft

1-1-8

Application And Removal Of Organic Coatings, Aerospace And Non-Aerospace Eqpt

1-1-17

Storage Of Acft And Missile Sys

1-1-19

Insp, Test And Repl Of Vibration Isolators On Eqpt In Acft

1-1-312

Use Of High Pressure Air And Nitrogen

1-1-689-3

Cleaning And Corrosion Control - Avionics And Electronics (Vol 111)

1-1-690

General Advanced Composite Repair Manual

1-1A-8

Aircraft Structural Hardware

1-1A-9

Engrg Series For Acft Rpr -- Aerospace Metals -- Genl Data And Usage Factors

1-1A-14

1-1A-15

General Maintenance Instructions for support

1-1A-14-2

Installation And Repair Practices, A/C Circular Electrical Connectors And Accessories

1H-1(U)N-21

Equipment Inventory List USAF Model UH-1N Helicopter

2-1-16

Reidentification By Serial Number Of Aircraft Engines

2J-T400-6-2

Depot Maintenance Twin Power Section Turbo shaft Engine Model T400-CP-400 and T 400-WV-402

3R12-4-3

Overhaul Instructions and Illustrated Parts Breakdown Engine to Transmission Driveshaft

3R17-5-3

Overhaul Instruction and Illustrated Parts Breakdown Vaneaxial Fan Assembly

5-1-2

Methods of Marking Instruments and Interpretation of Markings

5E6-1-103

Overhaul Instructions with Illustrated Parts Breakdown Master Caution Ind. Light

5F8-2-1-1

Calibration Instructions Pitot Static Installations

6J3-4-92-3

Overhaul Instructions with Illustrated Parts Breakdown Manual Fuel Control Unit

8D1-13-45-3

Overhaul Instructions with illustrated Parts Breakdown Linear Electro-Mechanical Actuator

8D10-14-2-3

O/H Instr With IPB -- Search And Landing Light

9H8-30-107-3

Maintenance and Overhaul Instructions Hydraulic Valve and Filter Assembly

9P5-14-45-3

Overhaul Instructions with Illustrated Parts Breakdown Variable Control Mixing Valve Assembly

11A18-14-7

Stor And Maint Proc – Fire Ext Crtg

13F3-1-104

Airborne Liquid Agent Fire Extinguishing Equipment Illustrated Parts Breakdown

13F6-12-3

Aircraft Fire Extinguisher Overhaul with Parts Breakdown

32A25-1-104

Vibrex System Track and Balance Illustrated Parts Breakdown

32B14-3-1-101

Operation & Service Installation torque indicating Devices

33K-1-100-2-CD-1

TMDE Calibration Interval Technical Order and Work Unit Code Reference Guide

34-1-3

Machinery and Shop Equipment Inspection and Maintenance

35-1-24

Air Force Economic Repair/Replacement Criteria for Selected San Antonio Air Logistics Center (ALC) Managed Support Equipment

42A3-1-2

Cements, Sealant, and Coatings

42B2-1-1

Use And Grades Of Acft Eng Lubricating Oils

42B2-1-3

Fluids For Hyd Equip

42E1-1-1

Aerospace Hose Assemblies

44H1-1-2

Description and Use of Plate Vibration Insulators, Specification No. MIL-I-5432

44H1-1-11

Selection And Instl Instr -- Huck Lockbolts

35-1-246WC-1

Periodic Inspection Non-powered Aerospace Ground Equipment Aircraft Ground Servicing Equipment (FSC 1730) and Airfield Specialized Trucks and Trailers (FSC 1740)

HM-7M/BDW

Bracket Tow Bar and GHW

21C243G01

Engine Universal Wash Cart

LCL-1HS Acft Wash

Aircraft Wash Checklist

LCL-1HS Debrief

Aircraft Debrief Checklist

Air Force Instructions

Lead & Using Command Supplements

JBA & 811 OG Operating Instructions