Appendix_CCTV_Camera_and_Associated_Equipment_Specifications.pdf

P a g e | 1

DDOT CCTV camera specification April 4, 2012

DDOT CCTV CAMERA AND ASSOCIATED EQUIPMENT Specification

After receiving the Engineer’s approval of the catalog cuts, the contractor shall procure the CCTV camera, encoder and DSL modem for the cabinet, decoder and DSL modem for the TMC, mast arms and all other associated equipment as determined to be necessary according to the DDOT Standard Drawings, this special provision and as directed by DDOT personnel.

The following is a list of materials that are needed for the installation of CCTV Cameras:

1. 1ea,Honeywell ACUIX 35X Outdoor Pendant with clear lower dome and 8" pigtail with 14 pin connector factory installed, including ACUIX Pigtail Assembly, smoked Cover.

Note: Camera must operate with existing DDOT Philips/Bosch protocol

2. 1 ea PMA18BS Pole Mount Adapter

3. 1 each DWM19S Wall Mount

4. 1ea Remote Vision System panel mount camera interface power supply with surge protection on power data and video. 120 VAC Input, 24VAC camera power and heater/blower. Video output for local test monitor. Includes Phillips to Honeywell standard protocol conversion. Dimensions: 9" X 7" X 5" (HWD). Includes NEMA4X fiberglass enclosure (or approved equal)

5. 1ea, 25 foot Honeywell Composite Cable, for ACUIX model camera

6. 2 ea, ML624 Actelis Ethernet Access Device (EDA)

7. 2 ea, ML688 Actelis Copper Drop/Add (EDA(

8. 1 ea, Siqura Model C-60 encoder, with DC power adapter, and mating AC power cord

9. 1 ea, Siqura Model S-60 decoder, with DC power adapter, and mating AC power cord

10. RG-6 flooded coax cable (West Penn Wire # 6325 or equiv.)

11. 3-pair 19 gauge solid distribution cable (Type IMSA 60-6 or RUS

Spec. PE-54 BWFG) .)

12. IMSA 19-1, 7 conductor,14 gauge, stranded cable

13. 2ea, 1½" cast iron hub plate (Pelco SE4124 or equivalent)

14. 2ea, Rubber grommet (sized to fit hole drilled into pole for cable

15. 1 ea, 1½" malleable iron LR or LL threaded conduit body (drilled and tapped for 5/16-24 set screws)

16. 2 ea, neoprene gasket

17. 1 ea, galvanized conduit body cover (1½")

18. 30', 3/4" stainless steel metal strap banding (Band-It C206 or equivalent)

19. 6 ea, 3/4" stainless steel metal strap banding buckles (Band-It C256 or equivalent)

20. 2 ea universal channel clamp (Band-It SX0220 or equivalent)

21. 2 ea medium extrusion 8½" long (Band-It SX0073 or equivalent)

22. 1 ea Kellum Grip (Hubbell part # 02201037 or equiv.)

P a g e | 2

DDOT CCTV camera specification April 4, 2012

23. 2 ea 3M 4460-D shield connector

24. 1 ea BNC connector (West Penn Wire # CN-BM73-2 or equiv.)

25. 2 ea BNC connector (West Penn Wire # CN-BM73-5 or equiv.)

26. 1 ea RJ-11 jack (Suttle # 625A2-4-50)

27. 1 ea RJ-45 jack (Suttle # 625A28NK50)

28. 1 ea McCain Accessory Power Tap

29. 1 ea Tripp-Lite Power Strip (Model #PDU1215)

30. 1 ea RJ-11 telephone cord (comes with Modem)

31. 2 ea 3' Category 5 straight patchcord

32. 2 ea splicing sleeves for safety cable

33. 1 ea Hubbell HBL5965VY plug for camera cable

• Contractor shall install all required Cables to pole and mount equipment according to DDOT CCTV standards and as directed by DDOT ITS personnel.

• Communications pairs shall be assigned by DDOT.

These items are available from:

Wes Heilman

Hillcrest Enterprises

PH 410-252-2540

Fax 443-281-5600 wes@hillcrestenterprises.com