Drawing Vol 1-8 Mechanical 614-700-MH-20231011.pdf

H

C

C

1. UNLESS NOTED OTHERWISE, THE SIZE OF EACH BRANCH DUCT TO A TERMINAL AIR BOX

(TAB) SHALL MATCH THE INLET SIZE UNLESS THE BRANCH IS GREATER THAN 6FEET IN

LENGTH, IN WHICH CASE THE BRANCH DUCT SHALL BE SIZED AT A PRESSURE DROP OF

0.07"W.C. PER 100' OF DUCTWORK.

2. UNLESS NOTED OTHERWISE, THE SIZE OF EACH BRANCH DUCT TO AN AIR TERMINAL SHALL

MATCH THE INLET SIZE.

3. ALIGN TEMPERATURE SENSORS WITH LIGHT SWITCHES WHEN IN CLOSE PROXIMITY TO

EACH OTHER.

4. PROVIDE ACCESS DOORS AT ALL DUCT MOUNTED EQUIPMENT.

5. EXISTING AIR INLET AND OUTLET CFM SHOWN ON DRAWINGS ARE FROM EXISTING

DRAWINGS, AND ARE FOR REFERENCE ONLY.

6. CONTRACTOR MAY REUSE PORTIONS OF EXISTING DUCT PROVIDED SIZES AND PRESSURE

CLASSES ARE CORRECT, DUCT IS THOROUGHLY CLEANED AND FREE OF DEFECTS, AND ALL

TRANSVERSE JOINTS, LONGITUDINAL SEAMS, AND DUCT WALL PENETRATIONS ARE SEALED

AS SPECIFIED FOR NEW DUCTWORK.

VENTILATION GENERAL NOTES:

1. THE SIZE OF BRANCH PIPING TO TERMINAL HEATING DEVICES AND COILS SHALL BE 3/4"

UNLESS NOTED OTHERWISE.

2. PIPE DRAIN LINES FROM EQUIPMENT TO NEAREST FLOOR DRAIN.

3. INSTALL ALL REFRIGERANT LIQUID AND SUCTION PIPING SIZED PER EQUIPMENT

MANUFACTURER RECOMMENDATIONS.

PIPING GENERAL NOTES:

MECHANICAL GENERAL NOTES:

THESE NOTES APPLY TO ALL MECHANICAL SHEETS AND TRADES, INCLUDING BUT NOT LIMITED

TO, FIRE PROTECTION, PLUMBING, MEDICAL GAS, VENTILATION, PIPING AND TEMPERATURE

CONTROL.

1. DRAWINGS SHOWING LOCATIONS OF EQUIPMENT, DUCTWORK, PIPING, ETC. ARE

DIAGRAMMATIC AND MAY NOT ALWAYS REFLECT EXACT INSTALLATION CONDITIONS.

DRAWINGS SHOW THE GENERAL ARRANGEMENT OF DUCTWORK, PIPING, EQUIPMENT, ETC.,

AND MAY NOT INCLUDE ALL OFFSETS AND FITTINGS REQUIRED FOR COMPLETE

INSTALLATION. THE DRAWINGS SHALL BE FOLLOWED AS CLOSELY AS ACTUAL BUILDING

CONSTRUCTION AND THE WORK OF OTHERS WILL PERMIT.

2. DO NOT SCALE DRAWINGS. VERIFY ALL DIMENSIONS AND CLEARANCES FROM

ARCHITECTURAL, STRUCTURAL, SUBMITTALS, AND OTHER APPROPRIATE DRAWINGS OR

PHYSICALLY AT SITE. REVIEW ALL DRAWINGS, INCLUDING THOSE OF OTHER TRADES.

3. COORDINATE ALL WORK WITH ALL OTHER TRADES PRIOR TO INSTALLATION TO PROVIDE

CLEARANCES REQUIRED FOR OPERATION, MAINTENANCE, CODE COMPLIANCE, AND TO

VERIFY NON-INTERFERENCE WITH OTHER WORK. DO NOT FABRICATE PRIOR TO

VERIFICATION OF NECESSARY CLEARANCES FOR ALL TRADES. BRING ANY INTERFERENCES

OR CONFLICTS TO THE ATTENTION OF THE ARCHITECT/ENGINEER BEFORE PROCEEDING

WITH FABRICATION OR EQUIPMENT ORDERS.

4. REVIEW SPACE REQUIREMENTS OF EQUIPMENT SPECIFIED OR SUBSTITUTED AND MAKE

REASONABLE ACCOMMODATIONS IN LAYOUT AND POSITIONING TO PROVIDE PROPER

ACCESS.

5. ANY CHANGES REQUIRED TO ELIMINATE CONFLICTS OR THAT RESULT FROM A FAILURE TO

COORDINATE SHALL BE MADE BY THE CONTRACTOR WITHOUT ADDITIONAL COST OR

EXPENSE TO OTHERS.

6. EACH CONTRACTOR IS RESPONSIBLE FOR ALL COSTS ASSOCIATED WITH ELECTRICAL

CHANGES REQUIRED FOR EQUIPMENT PROPOSED THAT DIFFERS FROM THE BASIS OF

DESIGN.

7. REFER TO ARCHITECTURAL REFLECTED CEILING PLAN, ELECTRICAL, TECHNOLOGY

AUDIO/VISUAL, AND OTHER MECHANICAL PLANS FOR EXACT LOCATIONS OF ALL CEILING

MOUNTED DEVICES, OTHER THAN SPRINKLERS.

8. EACH CONTRACTOR IS RESPONSIBLE FOR DAMAGE CAUSED BY THEIR ACTIONS TO WALLS,

FLOORS, CEILINGS, AND ROOFS. THE CONTRACTOR WHOSE WORK CAUSES DAMAGE IS

RESPONSIBLE FOR PATCHING TO MATCH ORIGINAL CONSTRUCTION, FIRE RATING, AND

FINISH.

9. IN AREAS WITH DRYWALL CEILINGS COORDINATE LOCATIONS OF ACCESS PANELS WITH THE

GC FOR ACCESS TO VALVES, DUCTWORK ACCESSORIES, DAMPERS, ETC. COORDINATE

PANEL TYPE AND COLOR WITH ARCHITECT. NOTIFY THE GC OF THE REQUIRED ACCESS

PANELS PRIOR TO BIDDING.

10. SEAL ALL FLOOR, WALL, AND ROOF PENETRATIONS AIRTIGHT WHERE CONDUITS, PIPING,

AND DUCTS PENETRATE. PENETRATIONS THROUGH EXTERIOR WALLS AND ROOF SHALL BE

SEALED AIRTIGHT WITH WATERPROOFING MATERIALS RECOMMENDED BY MANUFACTURER

FOR OUTDOOR USE.

11. CAULK ALL PIPE AND DUCT PENETRATIONS OF FULL HEIGHT NON-FIRE RATED WALL,

PARTITION, FLOOR, AND ROOF ASSEMBLIES. THIS IS ESSENTIAL TO PREVENT NOISE

TRANSMISSION FROM ONE ROOM TO ANOTHER AND TO PROVIDE THE DESIRED NC LEVELS

WITHIN ROOMS.

12. WHERE PIPES AND DUCTS ARE SHOWN TO PENETRATE FLOORS, PROVIDE SLEEVED

OPENINGS WITH THE TOP EDGE RAISED ABOVE FLOOR SURFACE IN ACCORDANCE WITH ALL

RELEVANT SPEC SECTIONS. SEAL SLEEVE PERIMETER TO BE WATERTIGHT.

13. EQUIPMENT SIZES AND SERVICE CLEARANCE REQUIREMENTS VARY AMONG DIFFERENT

MANUFACTURERS. CONSULT APPROVED SHOP DRAWINGS FOR EQUIPMENT SIZES AND

REQUIRED SERVICE CLEARANCES. COORDINATE WITH LAYOUT OF EQUIPMENT PADS,

PIPING, DUCTWORK, ETC.

14. DO NOT BLOCK EQUIPMENT SERVICE CLEARANCES.

15. MAINTAIN A MINIMUM WORKING CLEARANCE OF 3’-6” IN FRONT OF ALL ELECTRICAL

EQUIPMENT REQUIRING MAINTENANCE, INSPECTION, AND TESTING INCLUDING BUT NOT

LIMITED TO PANELS, DISTRIBUTION PANELS, SWITCHBOARDS, MOTOR CONTROL CENTERS,

TRANSFORMERS, EQUIPMENT DISCONNECTS AND STARTERS.

16. MAINTAIN THE DEDICATED ELECTRICAL EQUIPMENT SPACE DEFINED BY THE WIDTH / DEPTH

OF ELECTRICAL EQUIPMENT MEASURED FROM THE FLOOR TO A HEIGHT 6’-0” ABOVE THE

EQUIPMENT OR THE STRUCTURAL CEILING, WHICHEVER IS LOWER. SYSTEMS FOREIGN TO

THE ELECTRICAL DISTRIBUTION SYSTEM ARE NOT ALLOWED IN THE DEDICATED

ELECTRICAL SPACE INCLUDING: DUCTWORK, PIPING, ETC.

17. DO NOT SUPPORT EQUIPMENT, PIPING, OR DUCTWORK FROM METAL DECKING OR OTHER

NON-STRUCTURAL BUILDING ELEMENTS. ANCHORS EMBEDDED IN CONCRETE SHALL BE

CRACKED CONCRETE APPROVED IN ACCORDANCE WITH SPECIFICATIONS.

MECHANICAL RENOVATION NOTES:

1. EXISTING CONDITIONS ARE SHOWN BASED ON INFORMATION OBTAINED FROM FIELD

SURVEYS, EXISTING BUILDING DOCUMENTS, AND STAFF. VERIFY EXISTING CONDITIONS AND

REPORT ANY CONFLICTS BEFORE PROCEEDING.

2. NOT ALL EXISTING DUCTWORK AND PIPING IS SHOWN. VERIFY EXISTING CONDITIONS

BEFORE STARTING WORK. NOTIFY ENGINEER OF ANY CONFLICTS WITH NEW WORK.

3. FIELD VERIFY THE AVAILABLE CLEARANCES FOR DUCTWORK AND PIPING BEFORE

FABRICATION. RISES AND DROPS MAY BE NECESSARY BECAUSE OF EXISTING FIELD

CONDITIONS.

4. EACH CONTRACTOR SHALL FIELD VERIFY ACCESSIBILITY TO THE AREA OF THEIR WORK AND

SHALL NOTIFY THE ARCHITECT/ENGINEER PRIOR TO BIDDING IF OTHER UTILITIES ARE

REQUIRED TO BE REMOVED OR RELOCATED TO ALLOW ACCESS TO THEIR AREA OF WORK.

5. THE GENERAL CONTRACTOR IS RESPONSIBLE FOR CUTTING, REMOVAL AND PATCHING OF

ROOFS, WALLS, AND FLOORS ASSOCIATED WITH WORK BY ALL CONTRACTORS.

CONTRACTORS SHALL NOTIFY THE GC OF AFFECTED AREAS PRIOR TO BIDDING.

6. THE GENERAL CONTRACTOR IS RESPONSIBLE FOR REMOVAL AND REPLACEMENT OF

CEILINGS, CEILING TILES, AND CEILING GRIDS ASSOCIATED WITH AREAS OF WORK BY ALL

CONTRACTORS. NOTIFY THE GENERAL CONTRACTOR OF AFFECTED AREAS PRIOR TO

BIDDING.

7. WHERE EXISTING MECHANICAL SYSTEMS ARE LOCATED IN AREAS THAT CONFLICT WITH

NEW EQUIPMENT, PIPING, OR DUCTWORK TO BE INSTALLED, EACH CONTRACTOR SHALL

EITHER ARRANGE NEW EQUIPMENT, PIPING, OR DUCTWORK IN SUCH A FASHION THAT IT

DOES NOT CONFLICT WITH EXISTING SYSTEMS, OR REWORK EXISTING MECHANICAL

SYSTEMS TO ALLOW FOR INSTALLATION OF NEW EQUIPMENT, PIPING, OR DUCTWORK.

8. PROVIDE TEMPORARY CONNECTIONS TO MAINTAIN EXISTING SYSTEMS IN SERVICE DURING

CONSTRUCTION. MAINTAIN ACCESS TO EXISTING MECHANICAL INSTALLATIONS THAT

REMAIN ACTIVE.

9. OBTAIN PERMISSION FROM OWNER BEFORE SHUTTING DOWN ANY SYSTEM FOR ANY

REASON. MAINTAIN SERVICE TO ALL COMPONENTS THAT ARE TO REMAIN UNTIL NEW

SYSTEMS ARE INSTALLED.

10. MAINTAIN EXISTING SYSTEM IN SERVICE UNTIL NEW SYSTEM IS COMPLETE AND READY FOR

TIE IN AND SWITCHOVER. DRAIN SYSTEM ONLY TO MAKE SWITCHOVERS AND

CONNECTIONS. OBTAIN PERMISSION FROM OWNER BEFORE PARTIALLY OR COMPLETELY

DRAINING SYSTEM. MAKE CHANGEOVER TO NEW SYSTEMS WITH MINIMUM OUTAGE.

11. DISCONNECT AND REMOVE MECHANICAL DEVICES AND EQUIPMENT SERVING EQUIPMENT

THAT HAS BEEN REMOVED.

MECHANICAL PHASING NOTES:

1. REFER TO ARCHITECTURAL DRAWINGS FOR GENERAL DESCRIPTION OF PHASES. REFER TO

ARCHITECT'S INSTRUCTIONS FOR MORE DETAILS AND PHASING SCHEDULES AND FOR

CONCURRENT WORK. MECHANICAL, ELECTRICAL AND TECHNOLOGY DRAWINGS DEPICT

THE INTENT OF THE FINAL DESIGN. THE MECHANICAL, ELECTRICAL, AND TECHNOLOGY

DRAWINGS DO NOT DEPICT THE MEANS AND METHODS TO MEET THE REQUIREMENTS OF

THE PHASING CRITERIA.

2. REVIEW PROJECT PHASING PLANS TO COORDINATE DEMOLITION WORK, OUTAGES, ETC.

WITH AFFECTED ADJACENT AREAS.

3. PROVIDE TEMPORARY DUCTWORK, PIPING, SHUTOFF VALVES, ZONE VALVES, ZONE

ALARMS, ETC. AS NEEDED TO MAINTAIN SERVICE TO ALL AREAS DURING ALL PHASES OF

PROJECT.

4. INSTALL TEMPORARY DUCTWORK, PIPING, SHUTOFF VALVES, ETC. AS NECESSARY TO KEEP

ALL OCCUPIED SPACES OPERATIONAL THROUGHOUT ALL PHASES OF THE PROJECT

5. PHASE DEMOLITION WORK TO MINIMIZE DOWNTIME.

6. COORDINATE PHASING IN MAIN COMPUTER ROOM WITH TELECOMMUNICATIONS PHASING

PLANS.

PLAN OR DETAIL NUMBER

PLAN OR DETAIL NAME

PLAN OR DETAIL SCALE

DETAIL REFERRED TO BY SECTION CUT

SHEET DETAIL IS LOCATED ON

NAME

VIEW NAME

1/8" = 1'-0"

M101

SIMSIM

INDICATES SIMILAR DETAIL REFERENCED

IN MULTIPLE LOCATIONS

LEVEL NAME

10'-0" HEIGHT ABOVE

PROJECT 0'-0"

1 INDICATES NOTE USED TO DESCRIBE

ADDITIONAL INFORMATION ABOUT

WORK REQUIRED, SPECIFIC TO THE

SHEET AND/OR DETAIL

N O R

HT

INDICATES DIRECTION OF TRUE NORTH

VIEW KEY

LINE TYPE AND TAG KEY:

NEW WORK BY THIS CONTRACTOR (WIDE LINE)

NEW

EXISTING TO BE REMOVED (SHORT DASHED PATTERN)

NEW UNDERFLOOR OR UNDERGROUND (LONG DASHED PATTERN)

EXISTING TO REMAIN OR WORK BY OTHERS (NARROW LINE)

EXISTING

EXISTING TO BE REMOVED BY OTHERS (SHORT DASHED PATTERN)

EXISTING UNDERFLOOR OR UNDERGROUND (LONG DASHED PATTERN)

HALFTONING DOES NOT MODIFY SCOPE.

'TAG'-E TAGS WITH DASH 'E' INDICATES THE REFERENCED OBJECT IS EXISTING

TAG UNDERLINED TAG INDICATES OBJECT IS IN-SCOPE. IF NEW, ADDITIONAL

INFORMATION IS AVAILABLE IN A SCHEDULE, MATERIAL LIST, OR SYMBOL LIST

INDICATES AN EXISTING SYSTEM'S POINT OF CONNECTION/REMOVAL

T101

THE LINE TYPES SHOWN ARE FOR THE CONVENIENCE OF THE CONTRACTOR. THE CONTRACTOR

SHALL VERIFY RATINGS WITH THE LATEST SET OF ARCHITECTURAL PLANS AND FURNISH ALL

MATERIALS REQUIRED TO COMPLY WITH THOSE RATINGS WHETHER SHOWN OR NOT.

FIRE / SMOKE BARRIER DESIGNATIONS

2 HOUR FIRE PARTITION

SMOKE PARTITION

1 HOUR FIRE/SMOKE PARTITION

2 HOUR FIRE/SMOKE PARTITION

1 HOUR FIRE PARTITION

INFRASTRUCTURE STANDARD FOR TELECOMMUNICATIONS SPACES: V3.1, JULY 1, 2021

VA FIRE PROTECTION DESIGN MANUAL: 8TH ED., JUNE 1, 2021

VA PHYSICAL SECURITY AND RESILIENCY DESIGN MANUAL: REV. JULY 1, 2021

VA PLUMBING DESIGN MANUAL: REV. JUNE 1, 2022

VA HVAC DESIGN MANUAL: REV. OCTOBER 1, 2022

VA SITE DESIGN MANUAL: REV. APRIL 1, 2021

NFPA 13 INSTALLATION OF SPRINKLER SYSTEMS: 2022 EDITION

NFPA 72 FIRE ALARM AND SIGNALING CODE: 2022 EDITION

NFPA 75 FIRE PROTECTION OF IT EQUIPTMENT: 2020 EDITION

NFPA 99 HEALTHCARE FACILITIES CODE: 2021 EDITION

NFPA 101 LIFE SAFETY CODE: 2021 EDITION

NFPA 2001 CLEAN AGENT FIRE EXTINGUISHING SYSTEMS: 2022 EDITION

INTERNATIONAL BUILDING CODE: 2021 EDITION

INTERNATIONAL MECHANICAL CODE: 2021 EDITION

INTERNATIONAL PLUMBING CODE: 2021 EDITION

APPLICABLE CODES AND STANDARDS

CONTRACTOR SHALL COMPLY WITH APPLICABLE CODES AND LOCAL AMENDMENTS.

MECHANICAL ABBREVIATION KEY

ABBR: DESCRIPTION:

NOT IN CONTRACTNIC

EA EXHAUST/RELIEF AIR

FD FIRE DAMPER

FSD FIRE/SMOKE DAMPER

MA MIXED AIR

OA OUTSIDE AIR

RA RETURN AIR

SA SUPPLY AIR

SD SMOKE DAMPER

TRANSFER DUCTTD

TERMINAL AIR BOXTAB

TYPICALTYP

NORMALLY CLOSEDN.C.

NORMALLY OPENN.O.

MIXING VALVEMV

PROJECT ALTITUDE: 338.00 FT. ABOVE SEA LEVEL

MECHANICAL DESIGN CONDITIONS:

SUMMER:

WINTER:

DESIGN CONDITIONS:

TYPICAL ROOM SETPOINTS (AT IT EQUIPMENT INLET):

BASED ON WEATHER DATA FOR: MEMPHIS, TENNESSEE

TR CONDITIONS: 41-95°F DRY BULB, 8-80% RELATIVE HUMIDITY

MCR CONDITIONS: 72-81°F DRY BULB, 8-60% RELATIVE HUMIDITY

SUMMER SETBACK: NONE

WINTER SETBACK: NONE

REFER TO CONTROL DIAGRAMS FOR ROOM SPECIFICS.

96.7°F DRY BULB, 77.2°F WET BULB

18.7°F DRY BULB

OCCUPANCY SENSORO

HUMIDISTAT SENSOR

CARBON MONOXIDE SENSOR

CARBON DIOXIDE SENSOR

H HUMIDISTAT / SENSOR

TEMPERATURE SENSOR WITH WELL

T

THERMOMETER WITH WELL (DIAL TYPE)T

THERMOMETER WITH WELL (FILLED TYPE)

DIRECTION OF AIR FLOW

FLEXIBLE DUCT

MANUAL VOLUME DAMPER

RISE IN DIRECTION OF AIR FLOWR

DUCT CAP

DROP IN DIRECTION OF AIR FLOWD

DUCT DOWN

DUCT UP

SUPPLY/OUTSIDE AIR DUCT SECTION

RETURN AIR DUCT SECTION

EXHAUST/RELIEF AIR DUCT SECTION

4-WAY DIFFUSER WITH BLANKOFF IN ONE DIRECTION

SD-1

6/115

AIR TERMINAL PROPERTIES SYMBOL

NECK SIZE/CFM

TERMINAL AIR BOX (REFER TO SCHEDULE)###

### TERMINAL AIR BOX w/REHEAT COIL (REFER TO SCHEDULE)

HUMIDIFIERH

OPPOSED BLADE DAMPER (REFER TO SCHEDULE)

PARALLEL BLADE DAMPER (REFER TO SCHEDULE)

DIFFERENTIAL PRESSURE SENSOR

PRESSURE SENSOR/MONITORP

PRESSURE SENSOR (DUCT MOUNTED)P

THERMOSTAT/SENSORT

TEMPERATURE SENSORT

THERMOSTAT/SENSOR WITH HEAVY DUTY ENCLOSURET

MECHANICAL SYMBOL LIST

SYMBOL: DESCRIPTION:

AIRFLOW MEASUREMENT SYMBOL

XX - AHU SYMBOL

Y - SEQUENTIAL NUMBER

XX-Y

NOT ALL SYMBOLS MAY APPLY.

FAN POWERED TERMINAL AIR BOX w/REHEAT COIL

(REFER TO SCHEDULE)

CONTROL VALVE (TWO-WAY)

PITCH PIPE IN DIRECTION

DIELECTRIC CONNECTION

UNION/FLANGE

BALANCING VALVE (NUMBER INDICATES GPM)

PIPE CAP

PIPE DOWN

PIPE UP OR UP/DOWN

DIRECTION OF FLOW IN PIPE

SHUTOFF VALVE NORMALLY OPEN

SHUTOFF VALVE NORMALLY CLOSED

THROTTLING VALVE

AUTOMATIC BALANCING VALVE

MIXING VALVE

CONTROL VALVE (THREE-WAY)

SOLENOID VALVE

CHECK VALVE

SAFETY/RELIEF VALVE

PRESSURE REDUCING VALVE (LIQUID/GAS)

TRIPLE DUTY VALVE (ANGLE TYPE)

TRIPLE DUTY VALVE (IN-LINE TYPE)

VACUUM BREAKER

"WYE" - STRAINER

"WYE" - STRAINER W/SHUTOFF VALVE AND HOSE CONNECTION WITH CAP

BASKET STRAINER

FLEXIBLE CONNECTION

PRESSURE/TEMPERATURE TEST PLUG

REDUCER - REFERENCE SPECIFICATION

FOR CONCENTRIC/ECCENTRIC AND FOT/FOB

SUCTION DIFFUSER WITH SUPPORT FOOT

AUTOMATIC AIR VENT

MANUAL AIR VENT

DRAIN VALVE WITH HOSE CONNECTION AND CAP

ALIGNMENT GUIDE

PIPE ANCHOR

EXPANSION JOINT

#.#" IS THE EXPANSION TRAVEL INCHES

HEATING/CHILLED WATER RETURNHCR

CONDENSER WATER RETURNCR

CONDENSER WATER SUPPLYCS

CHILLED WATER RETURNCWR

CHILLED WATER SUPPLYCWS

HEATING WATER RETURNHWR

HEATING WATER SUPPLYHWS

REFRIGERANT LIQUIDLIQ

REHEAT WATER RETURNRWR

REHEAT WATER SUPPLYRWS

REFRIGERANT SUCTIONSUC

HEATING/CHILLED WATER SUPPLYHCS

CONDENSATE DRAINCD

PUMP

PRESSURE GAUGE (FURNISHED WITH BALL VALVE)P

DIFFERENTIAL PRESSURE SENSOR

PRESSURE SENSOR (FURNISHED WITH BALL VALVE)P

FLOW METER

FM

FLOW SWITCH

F

FS FLOW SENSOR

MECHANICAL SYMBOL LIST

SYMBOL: DESCRIPTION:

NOT ALL SYMBOLS MAY APPLY.

BACKFLOW PREVENTER

EJ-#

REFRIGERANTREF

101 NORTH SEVENTH STREET

LOUISVILLE, KY 40202

P: 502.236.2344 www.imegcorp.com

PROJECT #22005162.00

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMPCONSULTANT

321 4 5 6 7 8 9 10

10360 Ellison Circle Omaha, NE 68134 Phone: 402.991.5520 www.specializedeng.com SES Project : 22122

1221 N. Pennsylvania St.

Indianapolis, IN 46202 Phone: 317.800.6388 www.guidondesign.com

GD Project : 22.3101

35% SCHEMATIC DESIGN 10/31/2022

65% DESIGN DEVELOPMENT 05/03/2023

95% CONSTRUCTION DOCUMENTS 08/16/2023

100% FINAL BID DOCUMENTS 09/27/2023

100% FINAL STAMPED BID DOCUMENTS 10/11/2023

B

IM

/2

.3

V A

M e m p h is

E H

R M

I n fr a s tr u c tu re /6

-7

.B

A

.M P

R

A

L L S e c ti o n .r v t

/1 /2

:3

:5

A M

M000

MECHANICAL GENERAL NOTES AND LEGENDS VA MEMPHIS INFRASTRUCTURE

UPGRADE

MEMPHIS, TN

614-22-700

N/A

10/11/2023 LDH CAH

100% FINAL STAMPED

BID DOCUMENTS

FULLY SPRINKLERED

MECHANICAL SHEET INDEX

M000 MECHANICAL GENERAL NOTES AND LEGENDS

B01-M100 B01 GROUND LEVEL PLAN - OVERALL

B01-M100AE B01 PARTIAL GROUND LEVEL PLAN - MECHANICAL - SECTION AE

B01-M100AW B01 PARTIAL GROUND LEVEL PLAN - MECHANICAL - SECTION AW

B01-M100BE B01 PARTIAL GROUND LEVEL PLAN - MECHANICAL - SECTION BE

B01-M100BW B01 PARTIAL GROUND LEVEL PLAN - MECHANICAL - SECTION BW

B01-M100CE B01 PARTIAL GROUND LEVEL PLAN - MECHANICAL - SECTION CE

B01-M100CW B01 PARTIAL GROUND LEVEL PLAN - MECHANICAL - SECTION CW

B01-M100J B01 PARTIAL GROUND LEVEL PLAN - MECHANICAL - SECTION J

B01-M101 B01 FIRST LEVEL PLAN - OVERALL

B01-M101AE B01 PARTIAL FIRST LEVEL PLAN - MECHANICAL - SECTION AE

B01-M101AW B01 PARTIAL FIRST LEVEL PLAN - MECHANICAL - SECTION AW

B01-M101BE B01 PARTIAL FIRST LEVEL PLAN - MECHANICAL - SECTION BE

B01-M101BW B01 PARTIAL FIRST LEVEL PLAN - MECHANICAL - SECTION BW

B01-M101CE B01 PARTIAL FIRST LEVEL PLAN - MECHANICAL - SECTION CE

B01-M101CW B01 PARTIAL FIRST LEVEL PLAN - MECHANICAL - SECTION CW

B01-M101J B01 PARTIAL FIRST LEVEL PLAN - MECHANICAL - SECTION J

B01-M102 B01 SECOND LEVEL PLAN - OVERALL

B01-M102AE B01 PARTIAL SECOND LEVEL PLAN - MECHANICAL - SECTION AE

B01-M102AW B01 PARTIAL SECOND LEVEL PLAN - MECHANICAL - SECTION AW

B01-M102BE B01 PARTIAL SECOND LEVEL PLAN - MECHANICAL - SECTION BE

B01-M102BW B01 PARTIAL SECOND LEVEL PLAN - MECHANICAL - SECTION BW

B01-M102CE B01 PARTIAL SECOND LEVEL PLAN - MECHANICAL - SECTION CE

B01-M102CW B01 PARTIAL SECOND LEVEL PLAN - MECHANICAL - SECTION CW

B01-M102J B01 PARTIAL SECOND LEVEL PLAN - MECHANICAL - SECTION J

B01-M103 B01 THIRD LEVEL PLAN - OVERALL

B01-M103BW B01 PARTIAL THIRD LEVEL PLAN - MECHANICAL - SECTION BW

B01-M103CW B01 PARTIAL THIRD LEVEL PLAN - MECHANICAL - SECTION CW

B01-M103J B01 PARTIAL THIRD LEVEL PLAN - MECHANICAL - SECTION J

B01-M104 B01 FOURTH LEVEL PLAN - OVERALL

B01-M104BW B01 PARTIAL FOURTH LEVEL PLAN - MECHANICAL - SECTION BW

B01-M104CW B01 PARTIAL FOURTH LEVEL PLAN - MECHANICAL - SECTION CW

B01A-M100 B01A GROUND LEVEL PLAN - OVERALL

B01A-M100D B01A PARTIAL GROUND LEVEL PLAN - MECHANICAL - SECTION D

B01A-M100E B01A PARTIAL GROUND LEVEL PLAN - MECHANICAL - SECTION E

B01A-M100F B01A PARTIAL GROUND LEVEL PLAN - MECHANICAL - SECTION F

B01A-M100G B01A PARTIAL GROUND LEVEL PLAN - MECHANICAL - SECTION G

B01A-M101 B01A FIRST LEVEL PLAN - OVERALL

B01A-M101D B01A PARTIAL FIRST LEVEL PLAN - MECHANICAL - SECTION D

B01A-M101E B01A PARTIAL FIRST LEVEL PLAN - MECHANICAL - SECTION E

B01A-M101F B01A PARTIAL FIRST LEVEL PLAN - MECHANICAL - SECTION F

B01A-M101G B01A PARTIAL FIRST LEVEL PLAN - MECHANICAL - SECTION G

B01A-M102 B01A SECOND LEVEL PLAN - OVERALL

B01A-M102D B01A PARTIAL SECOND LEVEL PLAN - MECHANICAL - SECTION D

B01A-M102E B01A PARTIAL SECOND LEVEL PLAN - MECHANICAL - SECTION E

B01A-M102F B01A PARTIAL SECOND LEVEL PLAN - MECHANICAL - SECTION F

B01A-M102G B01A PARTIAL SECOND LEVEL PLAN - MECHANICAL - SECTION G

B01A-M103 B01A THIRD LEVEL PLAN - OVERALL

B01A-M103D B01A PARTIAL THIRD LEVEL PLAN - MECHANICAL - SECTION D

B01A-M103E B01A PARTIAL THIRD LEVEL PLAN - MECHANICAL - SECTION E

B01A-M103F B01A PARTIAL THIRD LEVEL PLAN - MECHANICAL - SECTION F

B01A-M103G B01A PARTIAL THIRD LEVEL PLAN - MECHANICAL - SECTION G

B01A-M104 B01A FOURTH LEVEL PLAN - OVERALL

B01A-M104D B01A PARTIAL FOURTH LEVEL PLAN - MECHANICAL - SECTION D

B01A-M104E B01A PARTIAL FOURTH LEVEL PLAN - MECHANICAL - SECTION E

B01A-M104F B01A PARTIAL FOURTH LEVEL PLAN - MECHANICAL - SECTION F

B01A-M104G B01A PARTIAL FOURTH LEVEL PLAN - MECHANICAL - SECTION G

B01A-M105 B01A FIFTH LEVEL PLAN - OVERALL

B01A-M105D B01A PARTIAL FIFTH LEVEL PLAN - MECHANICAL - SECTION D

B01A-M105E B01A PARTIAL FIFTH LEVEL PLAN - MECHANICAL - SECTION E

B01A-M105F B01A PARTIAL FIFTH LEVEL PLAN - MECHANICAL - SECTION F

B01A-M105G B01A PARTIAL FIFTH LEVEL PLAN - MECHANICAL - SECTION G

B01A-M106 B01A SIXTH LEVEL ROOF PLAN - OVERALL - MECHANICAL

B05-M100 B05 GROUND LEVEL PLAN - OVERALL

B05-M100A B05 PARTIAL GROUND LEVEL PLAN - MECHANICAL - SECTION 5A

B05-M100B B05 PARTIAL GROUND LEVEL PLAN - MECHANICAL - SECTION 5B

B05-M101 B05 FIRST LEVEL PLAN - OVERALL

B05-M101A B05 PARTIAL FIRST LEVEL PLAN - MECHANICAL - SECTION 5A

B05-M101B B05 PARTIAL FIRST LEVEL PLAN - MECHANICAL - SECTION 5B

B05-M102 B05 SECOND LEVEL PLAN - OVERALL

B05-M102A B05 PARTIAL SECOND LEVEL PLAN - MECHANICAL - SECTION 5A

B07-M100 B07 GROUND LEVEL PLAN - OVERALL

B07-M100A-B B07 PARTIAL GROUND LEVEL PLAN - MECHANICAL - SECTION 7A-B

B07-M100C B07 PARTIAL GROUND LEVEL PLAN - MECHANICAL - SECTION 7C

B07-M100D-E B07 PARTIAL GROUND LEVEL PLAN - MECHANICAL - SECTION 7D-E

B07-M101 B07 FIRST LEVEL PLAN - OVERALL

B07-M101A B07 PARTIAL FIRST LEVEL PLAN - MECHANICAL - SECTION 7A

B07-M101B B07 PARTIAL FIRST LEVEL PLAN - MECHANICAL - SECTION 7B

B07-M101C B07 PARTIAL FIRST LEVEL PLAN - MECHANICAL - SECTION 7C

B07-M101D B07 PARTIAL FIRST LEVEL PLAN - MECHANICAL - SECTION 7D

B07-M101E B07 PARTIAL FIRST LEVEL PLAN - MECHANICAL - SECTION 7E

B07-M102 B07 SECOND LEVEL PLAN - OVERALL

B07-M102A B07 PARTIAL SECOND LEVEL PLAN - MECHANICAL - SECTION 7A

B07-M102B-E B07 PARTIAL SECOND LEVEL PLAN - MECHANICAL - SECTION 7B-E

B07-M102C-D B07 PARTIAL SECOND LEVEL PLAN - MECHANICAL - SECTION 7C-D

B10-M100 B10 PARTIAL GROUND LEVEL PLAN - MECHANICAL

M400 MECHANICAL DETAILS

M500 MECHANICAL DIAGRAMS

M600 MECHANICAL SCHEDULES

M700 TEMPERATURE CONTROLS DIAGRAMS AND SEQUENCES

GRAND TOTAL: 90

Revisions: Date:

101 NORTH SEVENTH STREET

LOUISVILLE, KY 40202

P: 502.236.2344 www.imegcorp.com

PROJECT #22005162.00

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMPCONSULTANT

321 4 5 6 7 8 9 10

KEYPLAN N

AW

BW

CW CE

BE

AE

7C

7D 7E

7B

7A

GF

E D

J

5A

5BE

10360 Ellison Circle Omaha, NE 68134 Phone: 402.991.5520 www.specializedeng.com SES Project : 22122

1221 N. Pennsylvania St.

Indianapolis, IN 46202 Phone: 317.800.6388 www.guidondesign.com

GD Project : 22.3101

5BW

35% SCHEMATIC DESIGN 10/31/2022

65% DESIGN DEVELOPMENT 05/03/2023

95% CONSTRUCTION DOCUMENTS 08/16/2023

100% FINAL BID DOCUMENTS 09/27/2023

100% FINAL STAMPED BID DOCUMENTS 10/11/2023

B

IM

/2

.3

V A

M e m p h is

E H

R M

I n fr a s tr u c tu re /6

-7

.B

A

.M P

R

A

L L S e c ti o n .r v t

/1 /2

:3

:2

A M

B01-M100

B01 GROUND LEVEL PLAN - OVERALL VA MEMPHIS INFRASTRUCTURE

UPGRADE

MEMPHIS, TN

614-22-700

10/11/2023 LDH CAH

100% FINAL STAMPED

BID DOCUMENTS

FULLY SPRINKLERED

SCALE: 1" = 20'-0"B01-M100

1 B01 - GROUND LEVEL PLAN - OVERALL

SHEET NOTES:

1. REFER TO SECTION PLANS ON SUBSEQUENT

DRAWINGS FOR ADDITIONAL INFORMATION.

2. HATCHED AREAS INDICATE LOCATIONS OF

NEW TELECOMMUNICATION ROOMS.

SHEET NOTES:

1. REFER TO SECTION PLANS ON SUBSEQUENT

DRAWINGS FOR ADDITIONAL INFORMATION.

2. HATCHED AREAS INDICATE LOCATIONS OF

NEW TELECOMMUNICATION ROOMS.

0 20' 40'10'

T H

T H

Q

R

S

T

U

U.7

V

V.8

W

18.818.417.517.116.215.915.3

14.9

1413121110

14.113.112.811.911.110.69.89.2 9.79.3

B01-M100AE

B01-M100AE

B01-M100AE

4REF 3/4"CD

AWG18B

AFGE

AEG18A

STAIR

NO-8

BIO MED EQUIP EQUIP MECH RM

AEG13

AFGE

AEG10

OFFICE

AEG10A

PROJET FILE

AEG 11

OFFICE

AEG15A

AEG11A

ENV. MANAGMENT

AEG15

AEG11B

MENS TOILET

AEG12

WOMENS

TOILET

AEG 14

HAC

AWG42

AEG18

AEG 20E

ENGG CORRIDOR

AEG-C1

WORK ORDER

AEG17A

WORK RM

INT. DESIGN OFFICE

AEG15D

ENG CHIEF

AEG17B SECY

AEG17

SIGN SHOP

AEG 20

CONFERENCE

AEG 22

OFFICE

AEG24

OFFICE

AEG26

ENG TECH

AEG28

COPIER

AEG19A

ASST. CHIEF

AEG 17C

OFFICE

AWG59

CONFERENCE

OFFICE

AEG19

PLAN RM.

AEG 30

UNION

AEG21

MECH EQUP RM.

AEG 32

OFFICE

AEG19C

IRM COMPUTER

SHOP

AEG23

STAIR

REC / STO

AEG 70

EXISTING

MECH RM.

AEG33

CORRIDOR

STOR

AEG38

SERVER

AEG35

AEG 36

BREAK RM

AEG69

PHYSICS

AEG37CONFERENCE ROOM

AEG39

WORK ROOM

AEG41

CORRIDOR

MD

AEG68

AWG79

AWG80

CAD DRAFTING

AEG 30A

ADMIN ASST

AEG44

EXAM-2

AEG47

SUPPLY

AEG46

NURSES

AEG 60

CHEIF TECH

AEG 62

TLT

AEG63

CHIEF OF SVC

AEG43

EQUIP

AEG73A

AEG50

ACCELERATOR

AEG73

MAZE

AEG52

RECEPTION

AEG54

STAGING

AEG4

EXAM

EXAM-4

AEG51

WAITING

AEG7

PT. TLT

AEG48

AEG57

SECY

AEG45

STFF TLT

AEF40

RESEARCH LAB

AEG 9C

RESEARCH LAB

AEG9

TISSUE CULLTURE

AEG9A

OFFICE

AEG9B

OFFICE

AEG9C

SIMULATOR

AEG55

TR

AEG15B

ENGG CORRIDOR

AEG-C1

AC-AEG15B

20x10 SA

24x24 OA

18x10 OA ø

S A

TR

AE15B

SG-1

8x6/50

AEG15B

OFFICE

20x10 SA

3"CWR

3"CWS

2 1/2"HWS

2 1/2"HWR

24x24 OA x1

O

A

3"MPS

1 1/2"LPC

ø

R A ø

S A

OFFICE

AEG15A

ENV. MANAGMENT

AEG15

AC-AEG15B

3"CWR

3"CWS

REF

3/4"CD

1 1/2"LPC

3"MPS

2 1/2"HWR

2 1/2"HWS

OFFICE

AEG15A

TR

AEG15B

101 NORTH SEVENTH STREET

LOUISVILLE, KY 40202

P: 502.236.2344 www.imegcorp.com

PROJECT #22005162.00

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMPCONSULTANT

321 4 5 6 7 8 9 10

KEYPLAN N

AW

BW

CW CE

BE

AE

7C

7D 7E

7B

7A

GF

E D

J

5A

5BE

10360 Ellison Circle Omaha, NE 68134 Phone: 402.991.5520 www.specializedeng.com SES Project : 22122

1221 N. Pennsylvania St.

Indianapolis, IN 46202 Phone: 317.800.6388 www.guidondesign.com

GD Project : 22.3101

5BW

35% SCHEMATIC DESIGN 10/31/2022

65% DESIGN DEVELOPMENT 05/03/2023

95% CONSTRUCTION DOCUMENTS 08/16/2023

100% FINAL BID DOCUMENTS 09/27/2023

100% FINAL STAMPED BID DOCUMENTS 10/11/2023

B

IM

/2

.3

V

A M e m p h is

E H

R M

I n fr a s tr u c tu re /6

-7

.B

A .M

P R

A

L L

S e c ti o n .r v t

/1 /2

:3

:3

A

M

B01-M100AE

B01 PARTIAL GROUND LEVEL PLAN -

MECHANICAL - SECTION AE

VA MEMPHIS INFRASTRUCTURE

UPGRADE

MEMPHIS, TN

614-22-700

10/11/2023 LDH CAH

100% FINAL STAMPED

BID DOCUMENTS

FULLY SPRINKLERED

SCALE: 1/16" = 1'-0"B01-M100AE

1 B01 - PARTIAL GROUND LEVEL PLAN - MECHANICAL - SECTION AE

SCALE: 1/4" = 1'-0"B01-M100AE

3 B01 - GROUND LEVEL - ENLARGED ROOM AEG15B - VENTILATION

SHEET NOTES:

1. DRIP PANS TO BE PROVIDED UNDER ALL

EXISTING HYDRNOIC, PLUMBING, AND FIRE

PROTECTION PIPING OVERHEAD IN TR

SPACES. FOR CLARITY DRIP PANS ARE ONLY

SHOWN ON PLUMBING DRAWINGS.

MECHANICAL CONTRACTOR SHALL

COORDINATE WITH PLUMBING CONTRACTOR

TO VERIFY ALL EXISTING AND NEW PIPING

OVERHEAD ARE PROVIDED WITH DRIP PAN

COVERAGE.

2. DO NOT SPILL CONDENSATE PIPING INTO DRIP

PANS OVER TR SPACES. COORDINATE

INSTALLATION OF REFRIGERANT AND

CONDENSATE PIPING WITH DRIP PAN

LOCATIONS. AVOID PENETRATIONS OF NEW

DRIP PANS. SEAL ANY NECESSARY

PENETRATIONS WATER TIGHT.

3. TEMPERATURE CONTROLS CONTRACTOR

SHALL COORDINATE LOCATION OF ALL DRIP

PANS FOR LEAK DETECTION MONITORING.

4. TEMPERATURE CONTROLS CONTRACTOR

SHALL BE RESPONSIBLE FOR INTEGRATION OF

ALL TEMPERATURE AND HUMIDITY SENSORS

INTO EXISTING FACILITY CONTROLS SYSTEM.

COORDINATE ALL RACK-MOUNTED SENSORS

WITH TELECOMMUNICATIONS CONTRACTOR.

5. ELECTRICAL AND TELECOMMUNICATIONS

EQUIPMENT SHOWN FOR REFERENCE ONLY.

SCALE: 1/4" = 1'-0"B01-M100AE

2 B01 - GROUND LEVEL - ENLARGED ROOM AEG15B - MECHANICAL DEMOLITION

SCALE: 1/4" = 1'-0"B01-M100AE

4 B01 - GROUND LEVEL - ENLARGED ROOM AEG15B - MECHANICAL PIPING

0 16' 32'8' 0 4' 8'2'

0 4' 8'2'

0 4' 8'2'

KEYNOTES:

1. REMOVE EXISTING CEILING DEVICE. DEMOLISH

DUCT TO POINT INDICATED AND CAP.

2. INSTALL WALL MOUNTED SPLIT SYSTEM PER

MANUFACTURER'S INSTRUCTIONS.

COORDINATE EXACT LOCATION WITH

ELECTRICAL AND TELECOMMUNICATIONS

CONTRACTORS.

3. INSTALL NEW SPLIT SYSTEM THERMOSTAT

AND HUMIDISTAT ON WALL ADJACENT TO

LIGHT SWITCH. REFER TO M700.

4. ROUTE CONDENSATE DRAIN PIPING ABOVE

CEILING TO HAC. ROUTE PIPING DOWN WALL

AND SPILL INTO MOP BASIN. TERMINATE

PIPING 3" ABOVE FLOOR OF MOP BASIN.

5. ROUTE REFRIGERANT LINESET, SIZED PER

MANUFACTURER'S INSTRUCTIONS, AS

INDICATED. REFER TO SHEET B01-M101AE FOR

CONTINUATION.

Q

R

S

T

U

U.7

V

V.8

W

9.2 9.79.3

87654321

8.37.97.16.25.84.94.13.62.71.91.30.70.3

GENERATORS

GB1103

TRANS VAULT

GB1102

STAIR

SW GEAR

GB1105A

OPEN TO BELOW

OFFICE

GB1105B

MECH ROOM

AWG 19

BOILE ROOM

(OPEN TO BELOW)

MECH RM

AWG 21

OFFICE

AWG 27

OFFICE

MEZZANINE

AWG23

WATER

TREATMENT

AWG 26A

STAIR

BOILER RM.

AWG 26

STAIR

LOGISTCIS

AWG24B

LOGISTICS

AWG24

CORRIDOR

AWG16

TOILET

AWG22

WORK ROOM

AWG24A

LOGISTICS

AWG20

LOGISTICS

AWG20A

LOGISTICS

AWG20B

CORRIDOR TO

NURSING

ROOM

LOGISTICS

CONFERENCE

AWG18

CLOSET

AWG18A

AWG18B

AFGE

AEG18A

STAIR

NO-8

BIO MED EQUIP

PIPE BASEMENT

MENS LOCKER

ROOM

AWG10

RESEARCH LAB

AEG 9C

ELEV MECH RM

AWG8

SWITCHGEAR

AWG15

101 NORTH SEVENTH STREET

LOUISVILLE, KY 40202

P: 502.236.2344 www.imegcorp.com

PROJECT #22005162.00

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMPCONSULTANT

321 4 5 6 7 8 9 10

KEYPLAN N

AW

BW

CW CE

BE

AE

7C

7D 7E

7B

7A

GF

E D

J

5A

5BE

10360 Ellison Circle Omaha, NE 68134 Phone: 402.991.5520 www.specializedeng.com SES Project : 22122

1221 N. Pennsylvania St.

Indianapolis, IN 46202 Phone: 317.800.6388 www.guidondesign.com

GD Project : 22.3101

5BW

35% SCHEMATIC DESIGN 10/31/2022

65% DESIGN DEVELOPMENT 05/03/2023

95% CONSTRUCTION DOCUMENTS 08/16/2023

100% FINAL BID DOCUMENTS 09/27/2023

100% FINAL STAMPED BID DOCUMENTS 10/11/2023

B

IM

/2

.3

V A

M e m p h is

E H

R M

I n fr a s tr u c tu re /6

-7

.B

A

.M P

R

A

L L S e c ti o n .r v t

/1 /2

:3

:4

A M

B01-M100AW

B01 PARTIAL GROUND LEVEL PLAN -

MECHANICAL - SECTION AW

VA MEMPHIS INFRASTRUCTURE

UPGRADE

MEMPHIS, TN

614-22-700

10/11/2023 LDH CAH

100% FINAL STAMPED

BID DOCUMENTS

FULLY SPRINKLERED

SCALE: 1/16" = 1'-0"B01-M100AW

1 B01 - PARTIAL GROUND LEVEL PLAN - MECHANICAL - SECTION AW

SHEET NOTES:

1. SHEET INCLUDED FOR REFERENCE ONLY. NO

MECHANICAL SCOPE IN THIS AREA.

0 16' 32'8'

TH

M

L

K

J

H

N

P

P1

P2

P4

P5

15.9

1514 16 17 18 1913121110

B01-M100BE

B01-M100BE

B01-M100BE

EC

EC

AEG1 EC

AEG1A

OFFICE RM

AEG3

IRM STAGING

STORAGE

STORAGE

STORAGE IRM

AEG4A

OIT WORK RM

AEG 5

LOBBY

PT. TLT

AEG 52

ELEC

AEG76

STAIR

HAC

OFFICE

C

OFFICE

CWG 20C

EEO OFFICE

CWG 15-C

EEO OFFICE

CWG 15B

CWG 16B

OFFICE

CWG 20D

BULKFEED AND

GENERAL STORAGE

BWG 10

A/C SHOP

BWG 4

A/C SHOP

BWG 4B

WOMEN'S

LOCKER & TLT

BWG 7

MENS LOCKER /

TOILET

BWG 8

CORRIDOR

BE C1

DIRTY CAGE

STAGING

BWG14

CLEAN CAGE

BEDDING / STAGING

BWG 13

EQUIP

POOL SVC ROOM

BECEG1

CORRIDOR

BW C20

ANIMAL 1

BEG 3

ANIMAL 2

BEG 4

ANIMAL RM. 3

BEG 5

ANIMAL RM. 4

BEG6 ANIMAL RM. 5

BEG7

ANIMAL RM. 6

BEG8

EXIST COMM

BEG 23A

STORAGE

BEG 23

AUTO WATER

BEG 24

HKS

BEC3

HSK

BG25

BRU OFFICE

BEG 26C

BRU OFFICE

BEG26B

OFFICE

CEG 58C

OFFICE

CEG58D

CLOSET

CEG 58E

OFFICE

CEG 58B

OFFICE

CEG 58A

OFFICE

CEG 45

KITCHENETTE

CEG 48C

BRU OFFICE

CEG 44

BRU OFFICE

CEG 43

BRU OFFICE

CEG 42BRU OFFICE

CEG 41

CONFERENCE

CEG48

HSRD CONFERENCE

CEG 38

HSRD

CEG 40

HSRD OFFICE

CEG39

HSRD OFFICE

CEG 34

HSRD OFFICE

CEG 35

HSRD OFFICE

CEG 36

MEN

CEG 32

WOMENS

CEG 33

ANIMAL RM. 7

BEG 13

ANIMAL RM 8

BEG 12

VMU STORAGE

BEG 14

HSRD BREAK

BEG 15 BEG 16

ANIMAL RM. 9

BEG11

BRU OFFICE

BEG 17

ANIMAL RM. 10

BEG 10

BRU OFFICE

BEG 18

BRU OFFICE

BEG 19

BRU OFFICE

BEG 20

ELECTRICAL

BEG 21

IRR

BEG22

PROCEDURE

BEG 9

CWG 20B

INFO SYSTEMS

SECURITY

CWG 16

CWG 16A

BREAK ROOM

CWG 16C

CONTAINMENT

BWG 11C

CONTAINMENT LAB

BWG 11D CONTAINMENT

BWG 11A

SHAFT

ANTE

BWG 11

EUTH

BWG 12

STORAGE

BWG 16

CORRIDOR

BECE -C2

CORRIDOR

CE C3

CORRIDOR

CE C2

CORRIDOR

WOMEN

CEG 48D

CORRIDOR

BG26

COPY

CEG 48B

A/V

CEG48A

ELECTRICAL

BWG 9

CORRIDOR

BW-C25

TR

AEG 2

CORRIDOR

BW-C25

3/4"CD

AEG2

FLOOR

MACHINE

AEG1B

STORAGE

48x24 EA

10x10 SA 10x10 SA

3/4"HWS

3/4"HWR

1 1 1

EC

AEG1A

CORRIDOR

BW-C25

CORRIDOR

BW-C25

AC-AEG2

SG-1

8x6/50

48x24 EA

10x10 SA

TR

AEG 2

CORRIDOR

BW-C25

AC-AEG2

R E

F

3/4"CD

EC

AEG1A

CORRIDOR

BW-C25

TR

AEG 2

TR

AEG 2

CORRIDOR

BW-C25

101 NORTH SEVENTH STREET

LOUISVILLE, KY 40202

P: 502.236.2344 www.imegcorp.com

PROJECT #22005162.00

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMPCONSULTANT

321 4 5 6 7 8 9 10

KEYPLAN N

AW

BW

CW CE

BE

AE

7C

7D 7E

7B

7A

GF

E D

J

5A

5BE

10360 Ellison Circle Omaha, NE 68134 Phone: 402.991.5520 www.specializedeng.com SES Project : 22122

1221 N. Pennsylvania St.

Indianapolis, IN 46202 Phone: 317.800.6388 www.guidondesign.com

GD Project : 22.3101

5BW

35% SCHEMATIC DESIGN 10/31/2022

65% DESIGN DEVELOPMENT 05/03/2023

95% CONSTRUCTION DOCUMENTS 08/16/2023

100% FINAL BID DOCUMENTS 09/27/2023

100% FINAL STAMPED BID DOCUMENTS 10/11/2023

B

IM

/2

.3

V A

M e m p h is

E H

R M

I n fr a s tr u c tu re /6

-7

.B

A

.M P

R

A

L L S e c ti o n .r v t

/1 /2

:3

:5

A M

B01-M100BE

B01 PARTIAL GROUND LEVEL PLAN -

MECHANICAL - SECTION BE

VA MEMPHIS INFRASTRUCTURE

UPGRADE

MEMPHIS, TN

614-22-700

10/11/2023 LDH CAH

100% FINAL STAMPED

BID DOCUMENTS

FULLY SPRINKLERED

SCALE: 1/16" = 1'-0"B01-M100BE

1 B01 - PARTIAL GROUND LEVEL PLAN - MECHANICAL - SECTION BE

SCALE: 1/4" = 1'-0"B01-M100BE

2 B01 - GROUND LEVEL - ENLARGED ROOM AEG2 - MECHANICAL DEMOLITION

SCALE: 1/4" = 1'-0"B01-M100BE

3 B01 - GROUND LEVEL - ENLARGED ROOM AEG2 - VENTILATION

SCALE: 1/4" = 1'-0"B01-M100BE

4 B01 - GROUND LEVEL - ENLARGED ROOM AEG2 - MECHANICAL PIPING

SHEET NOTES:

1. DRIP PANS TO BE PROVIDED UNDER ALL

EXISTING HYDRNOIC, PLUMBING, AND FIRE

PROTECTION PIPING OVERHEAD IN TR

SPACES. FOR CLARITY DRIP PANS ARE ONLY

SHOWN ON PLUMBING DRAWINGS.

MECHANICAL CONTRACTOR SHALL

COORDINATE WITH PLUMBING CONTRACTOR

TO VERIFY ALL EXISTING AND NEW PIPING

OVERHEAD ARE PROVIDED WITH DRIP PAN

COVERAGE.

2. DO NOT SPILL CONDENSATE PIPING INTO DRIP

PANS OVER TR SPACES. COORDINATE

INSTALLATION OF REFRIGERANT AND

CONDENSATE PIPING WITH DRIP PAN

LOCATIONS. AVOID PENETRATIONS OF NEW

DRIP PANS. SEAL ANY NECESSARY

PENETRATIONS WATER TIGHT.

3. TEMPERATURE CONTROLS CONTRACTOR

SHALL COORDINATE LOCATION OF ALL DRIP

PANS FOR LEAK DETECTION MONITORING.

4. TEMPERATURE CONTROLS CONTRACTOR

SHALL BE RESPONSIBLE FOR INTEGRATION OF

ALL TEMPERATURE AND HUMIDITY SENSORS

INTO EXISTING FACILITY CONTROLS SYSTEM.

COORDINATE ALL RACK-MOUNTED SENSORS

WITH TELECOMMUNICATIONS CONTRACTOR.

5. ELECTRICAL AND TELECOMMUNICATIONS

EQUIPMENT SHOWN FOR REFERENCE ONLY.

0 16' 32'8' 0 4' 8'2'

0 4' 8'2'

0 4' 8'2'

KEYNTOES:

1. REMOVE EXISTING CEILING DEVICE. DEMOLISH

DUCT TO POINT INDICATED AND CAP.

2. REMOVE EXISTING CEILING DEVICE. DEMOLISH

DUCT TO POINT INDICATED AND PREPARE FOR

RECONNECTION.

3. DEMOLISH EXISTING PIPING TO UNDERSIDE OF

FLOOR SLAB AND CAP.

4. INSTALL WALL MOUNTED SPLIT SYSTEM PER

MANUFACTURER'S INSTRUCTIONS.

COORDINATE EXACT LOCATION WITH

ELECTRICAL AND TELECOMMUNICATIONS

CONTRATORS.

5. CONNECT TO EXISTING DUCT AND EXTEND TO

NEW SIDEWALL GRILLE. PROVIDE TRANSITION

AS REQUIRED.

6. INSTALL NEW SPLIT SYSTEM THERMOSTAT

AND HUMIDISTAT ON WALL ADJACENT TO

LIGHT SWITCH. REFER TO SHEET M700.

7. ROUTE REFRIGERANT LINESET, SIZED PER

MANUFACTURER'S INSTRUCTIONS, AS

INDICATED. REFER TO SHEET B01-M101BE FOR

CONTINUATION.

8. ROUTE CONDENSATE DRAIN PIPING ABOVE

CEILING TO HAC. ROUTE PIPING DOWN WALL

AND SPILL INTO MOP BASIN. TERMINATE

PIPING 3" ABOVE FLOOR OF MOP BASIN.

T

T H

M

L

K

J

H

N

P

P1

P2

P4

P5

9876543

B01-PL100BW

B01-PL100BW

B01-PL100BW

B01-M100BW

2REF

3/4"CD

ELEV MECH RM

AWG8

ELEV LOBBY

FITNESS CENTER

AWG3

TLT

AWG10A

STORAGE

CORRIDOR

AW-C11

WOMENS LOCKER

RM

AWG 13

TOILETS &

SHOWERS

AWG11A

FEMALE LOUNGE

AWG 11

STAIR

CORRIDOR

BWC31A

AUTOPSY

CWG2

PARAFFIN

CWG4 FRAM STOR

CWG6A

OFFICE

CWG6B

LAB STORAGE LAB STORAGE

CWG 9

CYTOLOGY

CWG 7

OFFICE

CWG 7B

SCREENING

CWG 7A

OFFICE

CWG 20A

OFFICE

CWG 20C

COMPLIANCE

OFFICE

CWG 20MECH RM.

BWG 1REFRIGERANT

STORAGE

BWG 24B

REFRIGERANT

STORAGE

BWG 24A

ELEC SHOP

STORAGE

BWG 25

BIO MED SERVER

ROOM

BWG 2A

AC SHOP STORAGE

BWG24

EEO OFFICE

CWG 15A

HAC

CWG 14

EEO OFFICE

CWG 15-C

EEO OFFICE

CWG 15B

MECH ROOM

BIO MED

STORAGE

BWG 2

CHIEF

BWG 33B

CLERICAL SEC/WAIT

BWG 33

ASST

BWG33A

CORRIDOR

BWC 30

OFFICE

BWG30

OFFICE

BWG 29

CONF

BWG 28

CARE OFFICE

BWG 27

STUDY

BWG 26

CONSULT

BWG 32

PHARM

BWG 31

COPY

BWG33C

A/C SHOP

BWG 4

A/C SHOP

BWG 4B

OFFICE

BWG 4A

CORRIDOR

BWC 29

CORRIDOR

BWC 28

TR

AWG 9

TR

AWG 9

CORRIDOR

AW-C11

/4

"C D

AWG 9

LOCK SMITH

STORAGE

20x14 EA

"C

W S

"C

W R

CORRIDOR

AW-C11

CORRIDOR

AW-C11

AC-AWG9

REF

"C

W S

"C

W R

/4

"C D

CORRIDOR

AW-C11

TR

AWG 9

TR

AWG 9

CORRIDOR

AW-C11

AC-AWG9

20x14 EA x1

E

A

TR

AWG 9

CORRIDOR

AW-C11

SG-1

8x6/50

8x6 SA

101 NORTH SEVENTH STREET

LOUISVILLE, KY 40202

P: 502.236.2344 www.imegcorp.com

PROJECT #22005162.00

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMPCONSULTANT

321 4 5 6 7 8 9 10

KEYPLAN N

AW

BW

CW CE

BE

AE

7C

7D 7E

7B

7A

GF

E D

J

5A

5BE

10360 Ellison Circle Omaha, NE 68134 Phone: 402.991.5520 www.specializedeng.com SES Project : 22122

1221 N. Pennsylvania St.

Indianapolis, IN 46202 Phone: 317.800.6388 www.guidondesign.com

GD Project : 22.3101

5BW

35% SCHEMATIC DESIGN 10/31/2022

65% DESIGN DEVELOPMENT 05/03/2023

95% CONSTRUCTION DOCUMENTS 08/16/2023

100% FINAL BID DOCUMENTS 09/27/2023

100% FINAL STAMPED BID DOCUMENTS 10/11/2023

B

IM

/2

.3

V A

M e m p h is

E H

R M

I n fr a s tr u c tu re /6

-7

.B

A

.M P

R

A

L L S e c ti o n .r v t

/1 /2

:3

:0

A M

B01-M100BW

B01 PARTIAL GROUND LEVEL PLAN -

MECHANICAL - SECTION BW

VA MEMPHIS INFRASTRUCTURE

UPGRADE

MEMPHIS, TN

614-22-700

10/11/2023 LDH CAH

100% FINAL STAMPED

BID DOCUMENTS

FULLY SPRINKLERED

SCALE: 1/16" = 1'-0"B01-M100BW

1 B01 - PARTIAL GROUND LEVEL PLAN - MECHANICAL - SECTION BW

SCALE: 1/4" = 1'-0"B01-M100BW

2 B01 - GROUND LEVEL - ENLARGED ROOM AWG9 - MECHANICAL DEMOLITION

SCALE: 1/4" = 1'-0"B01-M100BW

3 B01 - GROUND LEVEL - ENLARGED ROOM AWG9 - MECHANICAL PIPING

SCALE: 1/4" = 1'-0"B01-M100BW

4 B01 - GROUND LEVEL - ENLARGED ROOM AWG9 - VENTILATION

SHEET NOTES:

1. DRIP PANS TO BE PROVIDED UNDER ALL

EXISTING HYDRNOIC, PLUMBING, AND FIRE

PROTECTION PIPING OVERHEAD IN TR

SPACES. FOR CLARITY DRIP PANS ARE ONLY

SHOWN ON PLUMBING DRAWINGS.

MECHANICAL CONTRACTOR SHALL

COORDINATE WITH PLUMBING CONTRACTOR

TO VERIFY ALL EXISTING AND NEW PIPING

OVERHEAD ARE PROVIDED WITH DRIP PAN

COVERAGE.

2. DO NOT SPILL CONDENSATE PIPING INTO DRIP

PANS OVER TR SPACES. COORDINATE

INSTALLATION OF REFRIGERANT AND

CONDENSATE PIPING WITH DRIP PAN

LOCATIONS. AVOID PENETRATIONS OF NEW

DRIP PANS. SEAL ANY NECESSARY

PENETRATIONS WATER TIGHT.

3. TEMPERATURE CONTROLS CONTRACTOR

SHALL COORDINATE LOCATION OF ALL DRIP

PANS FOR LEAK DETECTION MONITORING.

4. TEMPERATURE CONTROLS CONTRACTOR

SHALL BE RESPONSIBLE FOR INTEGRATION OF

ALL TEMPERATURE AND HUMIDITY SENSORS

INTO EXISTING FACILITY CONTROLS SYSTEM.

COORDINATE ALL RACK-MOUNTED SENSORS

WITH TELECOMMUNICATIONS CONTRACTOR.

5. ELECTRICAL AND TELECOMMUNICATIONS

EQUIPMENT SHOWN FOR REFERENCE ONLY.

0 16' 32'8' 0 4' 8'2'

0 4' 8'2'

0 4' 8'2'

KEYNOTES:

1. REMOVE EXISTING CEILING DEVICE. DEMOLISH

DUCT TO POINT INDICATED AND CAP.

2. REMOVE EXISTING CEILING DEVICE. DEMOLISH

DUCT TO POINT INDICATED AND PREPARE FOR

RECONNECTION.

3. INSTALL WALL MOUNTED SPLIT SYSTEM PER

MANUFACTURER'S INSTRUCTIONS.

COORDINATE EXACT LOCATION WITH

ELECTRICAL AND TELECOMMUNICATIONS

CONTRACTORS.

4. CONNECT TO EXISTING DUCT AND EXTEND TO

NEW SIDEWALL GRILLE. PROVIDE TRANSITION

AS REQUIRED.

5. INSTALL NEW SPLIT SYSTEM THERMOSTAT

AND HUMIDISTAT ON WALL ADJACENT TO

LIGHT SWITCH. REFER TO SHEET M700.

6. ROUTE REFRIGERANT LINESET, SIZED PER

MANUFACTURER'S INSTRUCTIONS, AS

INDICATED. REFER TO SHEET B01-M101AE FOR

CONTINUATION.

7. ROUTE CONDENSATE DRAIN PIPING ABOVE

CEILING TO MECHANICAL ROOM. ROUTE

PIPING DOWN WALL AND SPILL INTO FLOOR

DRAIN. TERMINATE PIPING WITHIN FLOOR

DRAIN BODY. PIPING SHALL NOT BE INSTALLED

IN SUCH A WAY THAT A TRIP HAZARD IS

CREATED.

8. ROUTE CONDENSATE DRAIN PIPING ABOVE

CEILING TO HAC. ROUTE PIPING DOWN WALL

AND SPILL INTO MOP BASIN. TERMINATE

PIPING 3" ABOVE FLOOR OF MOP BASIN.

G

F

E

D

C

B

A

1514 16 17 18 19131211109

OFFICE

6005A

OFFICE

POLICE OFFICE

CEG 22

OFFICE

CEG 22A

OFFICE

CEG22B

OFFICE

CEG 22C

OFFICE

CEG 22D

OFFICE

CEG 22E

OFFICE

CEG 22F

OFFICE

CEG 23E

EXAM

OFFICE

CEG 23D

EXAM OFFICE

CEG 23 B

EXAM OFFICE

CEG 23 C

STORAGE

CEG 22G

EMS

OFFICE

CEG 23

OFFICE

CEG 23A

EMS WORK

LENDER

CEG 24A

HAC OFFICE

CEG 24B

OFFICE

CEG 24C

OFFICE

CEG 24D

OFFICE

HOUSEKEEPING

CEG 24

EMS STORAGE

CEG 24 E

BREAK

CEG 26C

SUPV

CEG 26A

POLICE

CEG 27

POLICE

INVESTIGATION

CEG 28

STORAGE

CEG 29A

CEG 29

LOCKSMITH OFFICE

CEG 29B

MECH

CEG29C

STORAGE

CWG 31D

EMS STORAGE

CWG 31

GA ELECTRIC

CWG 47A

EMS STORAGE

CWG 47

MAIL ROOM

CWG 30

UPS

TRACKING

CWG 30B

REPRODUCTION

STORAGE

CWG 31 A COPY RM.

CEG 26B

STORAGE

CEG 57

OFFICE

CEG 56C

OFFICE

CEG 20A

POLICE

CEG 21

OFFICE

CEG20

POLICE

CEG 19A

STAIR

OFFICE

CEG 16D

CHIEF OFFICE

CEG 16C

CEG 19B

POLICE

CEG 19

FIRE CONTROL

CEG 18

OFFICE

CEG 16B

POLICE

CEG 16

POLICE OFFICE

CEG 16A

CORRIDOR

CE C1

CEG 5C

POLICE

CEG 5A

CEG 5B

CEG 7

CEG6CEG5

EVIDENCE

CEG 4

POLICE DISPATCH

CEG 1

STORAGE

CEG 3

COMM

CEG 52

VENDING

CEG 51

STORAGE

CEG 53

OFFICE

CEG 54 A

OFFICE

CEG 54 B

CLINICAL

CEG 54

OFFICE

CEG 54D

OFFICE

CEG 54 C

OFFICE

CEG 55B

OFFICE

CEG 55A

OFFICE

CEG55D

OFFICE

CEG 55C

OFFICE

CEG 55E

OFFICE

CEG 56B

OFFICE

CEG 56 A OFFICE

CEG 56D

OFFICE

CEG 56 E

OFFICE

CEG 46

OFFICE

CEG 47

HSRD OFFICE

CEG 50

HSRD OFFICE

CEG 49

HSRD OFFICE

CEG 37

TRAINEE

CEG 31

CEG 30

ISS

OFFICE

CWG 16D

OFFICE

POLICE TRAINING

CWG 20 D

VNGE OFFICE

CWG 26

VNGE OFFICE

CWG 27

OFFICEELEVATOR

ELEVATOR

ELEC CLOSET

MEN

CEG 48E

PASSENGER

ELEVATOR LOBBY

CWC 45

FEMALE

TLT

MALE

TLT

TR

TR

101 NORTH SEVENTH STREET

LOUISVILLE, KY 40202

P: 502.236.2344 www.imegcorp.com

PROJECT #22005162.00

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMPCONSULTANT

321 4 5 6 7 8 9 10

KEYPLAN N

AW

BW

CW CE

BE

AE

7C

7D 7E

7B

7A

GF

E D

J

5A

5BE

10360 Ellison Circle Omaha, NE 68134 Phone: 402.991.5520 www.specializedeng.com SES Project : 22122

1221 N. Pennsylvania St.

Indianapolis, IN 46202 Phone: 317.800.6388 www.guidondesign.com

GD Project : 22.3101

5BW

35% SCHEMATIC DESIGN 10/31/2022

65% DESIGN DEVELOPMENT 05/03/2023

95% CONSTRUCTION DOCUMENTS 08/16/2023

100% FINAL BID DOCUMENTS 09/27/2023

100% FINAL STAMPED BID DOCUMENTS 10/11/2023

B

IM

/2

.3

V A

M e m p h is

E H

R M

I n fr a s tr u c tu re /6

-7

.B

A

.M P

R

A

L L S e c ti o n .r v t

/1 /2

:3

:1

A M

B01-M100CE

B01 PARTIAL GROUND LEVEL PLAN -

MECHANICAL - SECTION CE

VA MEMPHIS INFRASTRUCTURE

UPGRADE

MEMPHIS, TN

614-22-700

10/11/2023 LDH CAH

100% FINAL STAMPED

BID DOCUMENTS

FULLY SPRINKLERED

SCALE: 1/16" = 1'-0"B01-M100CE

1 B01 - PARTIAL GROUND LEVEL PLAN - MECHANICAL - SECTION CE

SHEET NOTES:

1. SHEET INCLUDED FOR REFERENCE ONLY. NO

MECHANICAL SCOPE IN THIS AREA.

TH

G

F

E

D

C

B

A

987654321

B01-M100CW

B01-M100CW

B01-M100CW

REF

CORRIDOR

CB1-9

HAC

DB1104

BMSA STORAGE

DB1103

TOILET

CWG40

TOILET

CWG41

BREAK ROOM

CWG 42

WAREHOUSE

CWG 32G STORAGE

CWG 31D

WAREHOUSE

STORAGE

CWG 32 F

PHARMACY

STORAGE

CWG 32 E

NITROUS OXIDE

CWG 33

NARCOTICS AND

ALCOHOL VAULT

CWG 32 A

OFFICE

CWG 35

LAUNDRY

CWG 39

WAREHOUSE

STORAGE

CWG 32 D

STORAGE

CWG 32 H

LAUNDRY

CWG 51 A

LAUNDRY

CWG 51B

EMS

CWG 46

BREAK ROOM /

STORAGE

CWG 48

EMS STORAGE

CWG 31

GA ELECTRIC

CWG 47A

EMS STORAGE

CWG 47

WRAPPING RM.

CWG 39A

UNIFORM ISSUE

CWG 39B

WASH RM.

CWG 51

UNIFORM STORAGE

CWG 52

SVC ELEVATOR

LOBBY

CWC 44

MED

WASH

CWG 53

PATHOLOGY

STORAGE/LAB EMS STORAGE

CWG 12

LAB STORAGE LAB STORAGE

CWG 9

CONFERENCE RM.

CWG 15D

EEO OFFICE

CWG 15-C

ELEVATOR

ELEVATOR

ELEC CLOSET

TELECOM

ELEVATOR

S2

ELEVATOR

S3 PASSENGER

ELEVATOR LOBBY

CWC 45

TEL CLOSET

SIGN

CLOSET

TR

CWG 1

TR

CWG 1

SVC ELEVATOR

LOBBY

CWC 44

CU-CW160C

CU-CWG1.1

CU-CWG1.2

REF

REF 3/4"CD

3/4"CD

2"CHS

1 1/4"CHR

x8

S A

TR

CWG 1

TR

CWG 1

AC-CWG1.1

AC-CWG1.2

2"CHS

1 1/4"CHR

3/4"CD

3/4"CD

TR

CWG 1

TR

CWG 1

R E

F R

E F

AC-CWG1.1

AC-CWG1.2

SG-1

8x6/50

TR

CWG 1

8x6 SA

101 NORTH SEVENTH STREET

LOUISVILLE, KY 40202

P: 502.236.2344 www.imegcorp.com

PROJECT #22005162.00

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMPCONSULTANT

321 4 5 6 7 8 9 10

KEYPLAN N

AW

BW

CW CE

BE

AE

7C

7D 7E

7B

7A

GF

E D

J

5A

5BE

10360 Ellison Circle Omaha, NE 68134 Phone: 402.991.5520 www.specializedeng.com SES Project : 22122

1221 N. Pennsylvania St.

Indianapolis, IN 46202 Phone: 317.800.6388 www.guidondesign.com

GD Project : 22.3101

5BW

35% SCHEMATIC DESIGN 10/31/2022

65% DESIGN DEVELOPMENT 05/03/2023

95% CONSTRUCTION DOCUMENTS 08/16/2023

100% FINAL BID DOCUMENTS 09/27/2023

100% FINAL STAMPED BID DOCUMENTS 10/11/2023

B

IM

/2

.3

V A

M e m p h is

E H

R M

I n fr a s tr u c tu re /6

-7

.B

A

.M P

R

A

L L S e c ti o n .r v t

/1 /2

:3

:2

A M

B01-M100CW

B01 PARTIAL GROUND LEVEL PLAN -

MECHANICAL - SECTION CW

VA MEMPHIS INFRASTRUCTURE

UPGRADE

MEMPHIS, TN

614-22-700

10/11/2023 LDH CAH

100% FINAL STAMPED

BID DOCUMENTS

FULLY SPRINKLERED

SCALE: 1/16" = 1'-0"B01-M100CW

1 B01 - PARTIAL GROUND LEVEL PLAN - MECHANICAL - SECTION CW

SCALE: 1/4" = 1'-0"B01-M100CW

2 B01 - GROUND LEVEL - ENLARGED ROOM CWG1 - MECHANICAL DEMOLITION

SCALE: 1/4" = 1'-0"B01-M100CW

4 B01 - GROUND LEVEL - ENLARGED ROOM CWG1 - MECHANICAL PIPING

SCALE: 1/4" = 1'-0"B01-M100CW

3 B01 - GROUND LEVEL - ENLARGED ROOM CWG1 - VENTILATION

SHEET NOTES:

1. DRIP PANS TO BE PROVIDED UNDER ALL

EXISTING HYDRNOIC, PLUMBING, AND FIRE

PROTECTION PIPING OVERHEAD IN TR

SPACES. FOR CLARITY DRIP PANS ARE ONLY

SHOWN ON PLUMBING DRAWINGS.

MECHANICAL CONTRACTOR SHALL

COORDINATE WITH PLUMBING CONTRACTOR

TO VERIFY ALL EXISTING AND NEW PIPING

OVERHEAD ARE PROVIDED WITH DRIP PAN

COVERAGE.

2. DO NOT SPILL CONDENSATE PIPING INTO DRIP

PANS OVER TR SPACES. COORDINATE

INSTALLATION OF REFRIGERANT AND

CONDENSATE PIPING WITH DRIP PAN

LOCATIONS. AVOID PENETRATIONS OF NEW

DRIP PANS. SEAL ANY NECESSARY

PENETRATIONS WATER TIGHT.

3. TEMPERATURE CONTROLS CONTRACTOR

SHALL COORDINATE LOCATION OF ALL DRIP

PANS FOR LEAK DETECTION MONITORING.

4. TEMPERATURE CONTROLS CONTRACTOR

SHALL BE RESPONSIBLE FOR INTEGRATION OF

ALL TEMPERATURE AND HUMIDITY SENSORS

INTO EXISTING FACILITY CONTROLS SYSTEM.

COORDINATE ALL RACK-MOUNTED SENSORS

WITH TELECOMMUNICATIONS CONTRACTOR.

5. ELECTRICAL AND TELECOMMUNICATIONS

EQUIPMENT SHOWN FOR REFERENCE ONLY.

0 16' 32'8' 0 4' 8'2'

0 4' 8'2'

0 4' 8'2'

KEYNOTES:

1. DEMOLISH EXISTING FAN COIL UNIT AND ALL

ASSOCIATED DUCT WORK, CEILING DEVICES,

CONTROLS, ETC. DEMOLISH CHILLED WATER

AND CONDENSATE PIPING TO POINT

INDICATED AND CAP.

2. INSTALL WALL MOUNTED SPLIT SYSTEM PER

MANUFACTURER'S INSTRUCTIONS.

COORDINATE EXACT LOCATION WITH

ELECTRICAL AND TELECOMMUNICATIONS

CONTRACTORS.

3. INSTALL NEW SIDEWALL SUPPLY GRILLE

ABOVE DOOR. ROUTE 8X6 SA DUCT TO

EXISTING FAN COIL ABOVE LOBBY CEILING.

CONNECT NEW DUCT TO EXISTING SUPPLY

PLENUM.

4. INSTALL NEW SPLIT SYSTEM THERMOSTAT

AND HUMIDISTAT ON WALL ADJACENT TO

LIGHT SWITCH. REFER TO SHEET M700.

5. ROUTE NEW CONDENSATE DRAIN PIPING

ABOVE CEILING AS INDICATED. REFER TO

SHEET B01-M100BW FOR CONTINUATION.

6. ROUTE REFRIGERANT LINESET, SIZED PER

MANUFACTURER'S INSTRUCTIONS, AS

INDICATED.

7. REFRIGERANT PIPING UP. REFER TO SHEET

B01-M101BE FOR CONTINUATION.

8. INSTALL CONDENSING UNIT MOUNTED ON

WALL WITH MANUFACTURER'S WALL HANGING

KIT.

9. UNITS ARE STACKED VERITICALLY.

10. ALL EXTERIOR PIPING SHALL BE INSULATED,

JACKETED, AND SUPPORTED PER DETAILS

AND SPECIFICATIONS. ROUTE PIPING UP ON

EXTERIOR OF WALL TO ABOVE INTERIOR

CEILING HEIGHT AND TURN IN TO BUILDING.

SEAL ALL EXTERIOR PENETRATIONS WEATHER

TIGHT.

T H

2726252423222120

G

F

E

D

C

B

A

B01-M100J

B01-M100J

B01-M100J

REF

MECH EQUIP

AREA WAYSTAIR

HEALTH INFO RM.

OFFICE

6027 A

OFFICE

6018C

OFFICE

6018B

OFFICE

6018A

MAS

MASS CONFERENCE

CENTER

ELEC

AMBULATORY CARE

& PROCESSING

OFFICE

TRANSCRIPTION

6008A

OFFICE

OFFICE

ROI

TRANSCRIPTION

RELEASE OF INFO

GENERAL OFFICE

OFFICE

6018D

OFFICE

6018E

BUSINESS OFFICE

SUPPLY

OFFICE

6018F

OFFICE

6002A

OFFICE

OFFICE

6002B

BREAK ROOMHAC

CREDIT UNION

EMS STORAGE

SUPV MED

NURSE

OFFICE 6030

MEN

WOMEN

PUMP RM.

MEN

WOMEN

STAIR

MEDICAL RECORDS

OFFICE

6005A

OFFICE

OFFICE

CEG22B

OFFICE

CEG 22C

HSCPAC OFFICE

ELEVATOR MACHS

ELEVATOR

ELEVATOR

CORRIDOR

60-C4

CORRIDOR

60-C2

CORRIDOR

50-C1

ELEVATOR LOBBY

FILE SURV OFFICE

6003A

OFFICE

CEG 20A

POLICE

CEG 21

MEN

WOMEN

TR

TR

CORRIDOR

60-C2

OFFICE

2"CD

3/4"HWR

3/4"HWS

36x24 RA36x20 RA

8x5 EA x1

S

A x4

S A x5

E A

AC-6007.2

AC-6007.1

8x5 EA

36x24 RA x1

S

A

4SG-1

6x8/50

TR

AC-6007.1

AC-6007.2

R E

F

REF

2"CD

3/4"CD

TR

TR

101 NORTH SEVENTH STREET

LOUISVILLE, KY 40202

P: 502.236.2344 www.imegcorp.com

PROJECT #22005162.00

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMPCONSULTANT

321 4 5 6 7 8 9 10

KEYPLAN N

AW

BW

CW CE

BE

AE

7C

7D 7E

7B

7A

GF

E D

J

5A

5BE

10360 Ellison Circle Omaha, NE 68134 Phone: 402.991.5520 www.specializedeng.com SES Project : 22122

1221 N. Pennsylvania St.

Indianapolis, IN 46202 Phone: 317.800.6388 www.guidondesign.com

GD Project : 22.3101

5BW

35% SCHEMATIC DESIGN 10/31/2022

65% DESIGN DEVELOPMENT 05/03/2023

95% CONSTRUCTION DOCUMENTS 08/16/2023

100% FINAL BID DOCUMENTS 09/27/2023

100% FINAL STAMPED BID DOCUMENTS 10/11/2023

B

IM

/2

.3

V A

M e m p h is

E H

R M

I n fr a s tr u c tu re /6

-7

.B

A

.M P

R

A

L L S e c ti o n .r v t

/1 /2

:3

:3

A M

B01-M100J

B01 PARTIAL GROUND LEVEL PLAN -

MECHANICAL - SECTION J

VA MEMPHIS INFRASTRUCTURE

UPGRADE

MEMPHIS, TN

614-22-700

10/11/2023 LDH CAH

100% FINAL STAMPED

BID DOCUMENTS

FULLY SPRINKLERED

SCALE: 1/16" = 1'-0"B01-M100J

1 B01 - PARTIAL GROUND LEVEL PLAN - MECHANICAL - SECTION J

SCALE: 1/4" = 1'-0"B01-M100J

2 B01 - GROUND LEVEL - ENLARGED ROOM 6007 - MECHANICAL DEMOLITION

SCALE: 1/4" = 1'-0"B01-M100J

3 B01 - GROUND LEVEL - ENLARGED ROOM 6007 - VENTILATION

SCALE: 1/4" = 1'-0"B01-M100J

4 B01 - GROUND LEVEL - ENLARGED ROOM 6007 - MECHANICAL PIPING

SHEET NOTES:

1. DRIP PANS TO BE PROVIDED UNDER ALL

EXISTING HYDRNOIC, PLUMBING, AND FIRE

PROTECTION PIPING OVERHEAD IN TR

SPACES. FOR CLARITY DRIP PANS ARE ONLY

SHOWN ON PLUMBING DRAWINGS.

MECHANICAL CONTRACTOR SHALL

COORDINATE WITH PLUMBING CONTRACTOR

TO VERIFY ALL EXISTING AND NEW PIPING

OVERHEAD ARE PROVIDED WITH DRIP PAN

COVERAGE.

2. DO NOT SPILL CONDENSATE PIPING INTO DRIP

PANS OVER TR SPACES. COORDINATE

INSTALLATION OF REFRIGERANT AND

CONDENSATE PIPING WITH DRIP PAN

LOCATIONS. AVOID PENETRATIONS OF NEW

DRIP PANS. SEAL ANY NECESSARY

PENETRATIONS WATER TIGHT.

3. TEMPERATURE CONTROLS CONTRACTOR

SHALL COORDINATE LOCATION OF ALL DRIP

PANS FOR LEAK DETECTION MONITORING.

4. TEMPERATURE CONTROLS CONTRACTOR

SHALL BE RESPONSIBLE FOR INTEGRATION OF

ALL TEMPERATURE AND HUMIDITY SENSORS

INTO EXISTING FACILITY CONTROLS SYSTEM.

COORDINATE ALL RACK-MOUNTED SENSORS

WITH TELECOMMUNICATIONS CONTRACTOR.

5. ELECTRICAL AND TELECOMMUNICATIONS

EQUIPMENT SHOWN FOR REFERENCE ONLY.

0 16' 32'8' 0 4' 8'2'

0 4' 8'2'

0 4' 8'2'

KEYNOTES:

1. REMOVE EXISTING CEILING DEVICE. DEMOLISH

DUCT TO POINT INDICATED AND CAP.

2. REMOVE EXISTING CEILING DEVICE. DEMOLISH

DUCT TO POINT INDICATED AND PREPARE FOR

RECONNECTION.

3. INSTALL WALL MOUNTED SPLIT SYSTEM PER

MANUFACTURER'S INSTRUCTIONS.

COORDINATE EXACT LOCATION WITH

ELECTRICAL AND TELECOMMUNICATIONS

CONTRACTORS.

4. CONNECT TO EXISTING DUCT AND EXTEND TO

NEW SIDEWALL GRILLE. PROVIDE TRANSITION

AS REQUIRED.

5. INSTALL NEW SPLIT SYSTEM THERMOSTAT

AND HUMIDISTAT ON WALL ADJACENT TO

LIGHT SWITCH. REFER TO SHEET M700.

6. ROUTE 3/4" CONDENSATE DRAIN PIPING AS

INDICATED. HOLD TIGHT TO WALL. ROUTE

PIPING DOWN WALL AND ALONG FLOOR TO

SPILL INTO FLOOR DRAIN. TERMINATE PIPING

WITHIN DRAIN BODY. PIPING SHALL NOT

CREATE A TRIPPING HAZARD.

7. ROUTE REFRIGERANT LINESET, SIZED PER

MANUFACTURER'S INSTRUCTIONS, AS

INDICATED. REFER TO SHEET B01-M101J FOR

CONTINUATION.

P: 502.236.2344 www.imegcorp.com

PROJECT #22005162.00

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMPCONSULTANT

321 4 5 6 7 8 9 10

KEYPLAN N

AW

GF

E D

BW

CW CE

J

BE

AE

7D 7E

7B7C

7A

5A

10360 Ellison Circle Omaha, NE 68134 Phone: 402.991.5520 www.specializedeng.com SES Project : 22122

1221 N. Pennsylvania St.

Indianapolis, IN 46202 Phone: 317.800.6388 www.guidondesign.com

GD Project : 22.3101

5BE5BW

35% SCHEMATIC DESIGN 10/31/2022

65% DESIGN DEVELOPMENT 05/03/2023

95% CONSTRUCTION DOCUMENTS 08/16/2023

100% FINAL BID DOCUMENTS 09/27/2023

100% FINAL STAMPED BID DOCUMENTS 10/11/2023

B

IM

/2

.3

V A

M e m p h is

E H

R M

I n fr a s tr u c tu re /6

-…