BAA-03-05-PRKAmend06.doc

BAA 03-05-PRK AMENDMENT 06

BROAD AGENCY ANNOUNCEMENT (BAA) NUMBER

BAA 03-05-PRK

POWER AND THERMAL TECHNOLOGIES FOR AIR AND SPACE (PTTAS)

AMENDMENT 06 AND

CALL FOR PROPOSALS

CURRENT CALL TITLE: SMALL AND LIGHTWEIGHT PORTABLE POWER

SYSTEMS FOR AIRMEN

TECHNICAL POC: The technical POC for this call is: Capt. William Notbohm, AFRL/PRPS, Phone (937) 255-4226, e-mail: william.notbohm@wpafb.af.mil; USPS mail address: AFRL/PRPS, 1950 Fifth Street, Bldg. 18, WPAFB, OH 45433-7919.

CONTRACTING POC: Scott Savory, Contracting Officer, AFRL/PKPA, (937) 255-0335, e-mail: scott.savory@wpafb.af.mil; USPS mail address: AFRL/PKPA, Bldg 167, 2310 8th St., Wright-Patterson AFB, OH 45433-7801.

PROPOSAL DUE DATE AND TIME: 17 October 2005, 3:00 P.M. Eastern Daylight Time.

****NOTICE:***** Proposals received after the due date and time shall be governed by the provisions of FAR 52.215-1(c)(3).

Proposals should be submitted only to the following Contracting Point of Contact (POC) : Scott Savory, AFRL/PKPA, Bldg 167, 2310 8th St., Wright-Patterson AFB, OH 45433-7801. Proposals may NOT be submitted electronically. Any proposals received electronically will be rejected.

Note: Intent to Propose: Offerors that anticipate submitting a proposal are requested to submit an e-mail to Scott Savory, Contracting Officer, at scott.savory@wpafb.af.mil containing the name of the contractor, the POC, and the contractor’s intent to submit a proposal. This “intent to Propose” is requested by 16 September 2005, 3:00 P.M. EDT.

PART 1:

INTRODUCTION:

The Power Division (AFRL/PRP) of the Air Force Research Laboratory Propulsion Directorate is currently soliciting proposals under Broad Agency Announcement (BAA) 03-05-PRK in the area of Power Generation Technologies. This call (Amendment 06) is seeking proposals for “Small and Lightweight Portable Power Systems for Airmen.” Details for the technical aspects of this call are contained in PART 5 of this Amendment Detailed information on the over arching Power and Thermal Technologies for Air and Space (PTTAS) program is provided in the initial BAA announcement. The initial solicitation and subsequent amendments also provide detailed information and instructions concerning award information, proposal preparation instructions, data requirements, basis for award, and evaluation category definitions. Interested offerors may view and/or download the full text of the BAA 03-05-PRK with all amendments by accessing the Federal Business Opportunities (FedBizOpps) homepage at http://www.eps.gov/. Offerors are notified that BAA-03-05-PRK “Introduction” Section A through Section E, and Part 2 “Contract Data Requirements List” (CDRL) govern this call for proposals. Changes to any part of the foregoing are identified in this amendment. Accordingly; offerors are strongly encouraged to review the entire solicitation, including all amendments, prior to preparing and submitting a proposal for the current call.

PART 1 SECTION A—Paragraph 4-Other Requirements Item Identification and Valuation: Any contract award resulting from this solicitation may contain the clause at DFARS 252.211-7003, Item Identification and Valuation, (APR 2005) which requires unique item identification and valuation of any deliverable item for which the Government’s unit acquisition cost is $5,000 or more; subassemblies, components, and parts embedded within an item valued at $5,000 or more; or items for which the Government’s unit acquisition cost is less than $5,000 when determined necessary by the requiring activity for serially managed, mission essential, or controlled inventory. Also included are any DoD serially managed subassembly, component, or part embedded within a delivered item and the parent item that contains the embedded Subassembly, component, or part. Per DFARS 211.274-3 Policy for Valuation, it is DoD policy that contractors shall be required to identify the Government’s unit acquisition cost for all items delivered, even if none of the criteria for placing a unique item identification mark applies. Therefore, your proposal must clearly break out the unit acquisition cost for any deliverable items. Per DFARS 211.274-3 Policy for Valuation, “The Government’s unit acquisition cost is the Contractor’s estimated fully burdened unit cost at time of delivery to the Government for cost type or undefinitized line, subline, or exhibit line items” (Per DoD, “fully burdened unit costs” to the Government would include all direct, indirect, G&A costs, and an appropriate portion of fee.). If you have questions regarding the Unique Item Identification requirements, please contact the Contracting Point of Contact listed above. For more information, see the following website: http://www.acq.osd.mil/uid.

PART 1 SECTION D- BASIS FOR AWARD

1. Paragraph a. Technical Evaluation Criteria for CPFF contracts, CR contracts and Assistance Instruments, set forth in the basic announcement and repeated here for clarity, shall apply to this call for proposals.

(1) The proposal must reflect a new and creative solution that clearly demonstrates technical or scientific merit and be highly relevant to Air Force needs

(2) Successful development of the proposed effort must have a significant impact on advancing technology for air and/or space power applications

(3) The proposal, including the proposed Statement of Work (SOW), must reflect a sound technical approach

(4) The proposal must indicate that competent experienced engineering, scientific and technical personal are available to support the program and that necessary research/ test/ laboratory facilities are available

(5) The proposal must indicate that the offeror has quality experience with the technology to be developed

PART 4 PROPOSAL EVALUATION CATEGORY DEFINITIONS

1. The following Proposal Evaluation Category Definitions, which were set forth in Amendment 05 to the BAA, shall apply to this call for proposals:

i. Category I: Well conceived scientifically and technically sound proposals pertinent to program goals and objectives, and offered by a responsible contractor with the competent scientific and technical staff and supporting resources needed to ensure satisfactory program results. Proposals in Category I are recommended for acceptance subject to funding constraints.

ii. Category II: Proposals not technically sound or do not meet agency needs.

Broad Agency Announcement (BAA)

BAA-03-05-PRK AMENDMENT 06

Part 5 – CURRENT SOLICITATION TOPIC

PROGRAM TITLE: Small and Lightweight Portable Power Systems for Airmen ANTICIPATED AWARD DATE: 17 November 2005 TYPE OF AWARD: The Air Force anticipates award of a cost-reimbursement contract, a cost-sharing contract, or a cost-plus-fixed-fee contract. Offerors are highly encouraged to propose a cost sharing arrangement. The Air Force reserves the right to award a procurement contract.

NUMBER OF AWARDS: The Government anticipates making one award. The Government reserves the right to select for award any, all, part or none of the proposals received.

PROPOSAL PREPARATION INSTRUCTIONS: All proposals must be prepared in accordance with the Proposal Preparation Instructions contained in Part I - Section C of solicitation BAA 03-05-PRK available at the Fed Biz Ops website http://www1.eps.gov/spg/USAF/AFMC/AFRLWRS/BAA%2D03%2D05%2DPRK/listing.html.

WIDE AREA WORK FLOW: NOTICE: Any contract award resulting from this solicitation will contain the clause at DFARS 252.232-7003 “Electronic Submission of Payment Requests,” which requires electronic submission of all payment requests. The clause identifies three possible electronic formats through which to submit electronic payment requests. Pursuant to that clause, the Department of Defense is adopting the Wide Area Work Flow – Receipt and Acceptance (WAWF-RA) system as the preferred electronic method and which will apply any contracts resulting from this solicitation. Information regarding WAWF-RA, including web-based training and registration, can be found at https://wawf.eb.mil/index.html.

RELATED IR&D: Offerors shall identify any independent research and development programs conducted within the last three years in the technical areas of this solicitation. The significant results of such programs should be presented in the proposals. Include this information in the technical/management volume of your proposal.

SMALL AND DISADVANTAGED BUSINESS SUBCONTRACTING PLAN: Offerors submitting proposals for contacts are notified that in accordance with Federal Acquisition Regulation (FAR) 19.702, any contract that is expected to exceed $500,000 and that has subcontracting possibilities requires a subcontracting plan. Proposed subcontracting plan must be submitted with the offeror’s proposal. Small business concerns are exempt from this requirement (FAR 19-702(b)).

REPS AND CERTS PACKAGES: Potential offerors are notified that effective 01 Jan 2005 to be eligible for an award, they must submit annual Electronic Representations and Certifications, otherwise known as On-line Representations and Certifications Application (ORCA) via the Business Partner Network (BPN) at http://www.bpn.gov/orca. These FAR level representations and certifications are required in addition to the representations and certifications specific to this acquisition. Before submitting the Electronic Representations and Certifications, contractors must be registered in the Central Contractor Registration (CCR) Database. On-line registration instructions can be accessed from the Wright Research Site Contracting Office home page at http://www.wrs.afrl.af.mil/contract/ or the DISA CCR home page at http://www.ccr.gov/. In addition, a local representations and certifications package is included with this amendment. Offerors must complete and include this package with your proposal.

STATEMENT OF OBJECTIVES:

General Description:

The purpose of this effort is to develop a hybrid power system that will be used to power multiple electronic devices in a military environment. The objective is to deliver between 2 and 5 prototype systems that are sufficiently rugged to undergo field testing while meeting the system energy density goals. The system should consist of three components: 1) a rechargeable battery 2) a high specific energy recharging source, and 3) a power manager. The entire system must be able to deliver between 1800 and 3000 Watthours over a 72 hour period and should not weigh over 16.5 lbs. (The electronic equipment being powered, and their connecting cords are not included in this weight) The devices to be powered fall into two voltage categories, a high voltage range 20-34V, and a low voltage range 10-18V. The system must be able to provide for both voltage outputs in as energy efficient manner as possible. All DC/DC conversions should be greater than 90% efficiency, with a goal of being above 95% efficiency. A basic schematic is provided below:

Figure 1: Basic Schematic of Power System

Detailed information on the required connectors will be supplied upon contract award. A weight and specific energy breakdown is provided as an example of how the system will be evaluated. The following breakdown that is included is for example purposes only, and should not be construed as a requirement. Any system combination is acceptable as long as it meets the guidelines laid out in the specifications section.

Table 1: Example Weight and Energy Breakdown for Hypothetical System

Batteries and Circuitry

5 lbs ( 2.5 kg)

135 Wh/kg

340 Wh

Fuel Cell plus Fuel

9.5 lbs (4.9 kg) 405 Wh/kg

1,660 Wh

Power Manager plus cords 1 lb (.5 kg)

Total Energy System

16.5 lbs (7.5kg) 266 Wh/kg

2,000 Wh

The concept of operations for this system is for the energy storage (batteries) to be kept as near a full state of charge as possible throughout operation of the system, with an emphasis on using available energy as efficiently as possible.

System Requirements:

The following requirements pertain to the entire hybrid power system. Threshold values are given as the minimum performance requirements to meet. Objective values are provided as goals to strive for. Demonstrating the capability to exceed thresholds and meet objective values in as many areas as possible is highly desirable in this effort and will be used as a discriminator in the selection process.

Aural Signature:

Aural Detectability- (per MIL-STD 1474D Requirement 2, Table 2-11)

Threshold:

1) High Specific Energy Power Source Off: 30 Meter Aural Non-Detectability

2) High Specific Energy Power Source On: 100 Meter Aural Non-Detectability

Objective:

1) High Specific Energy Power Source Off: 10 Meter Aural Non-Detectability

2) High Specific Energy Power Source On: 30 Meter Aural Non-Detectability

Operating Temperature:

Environmental Temperature range:

Threshold: -5 to 55C continuous operation per MIL-STD 810F Table 502.4-II and Table 501.4-II for basic hot and cold environments. System components do not have to meet energy density targets below 0C and above 45C.

Objective: -20 to 55C continuous operation

Start-Up Temperature:

Threshold: -5C unassisted start-up (system should start up under its own battery power)

Objective: -20C unassisted start up

Orientation:

Storage and Transport: Orientation Independent

Operation:

Threshold: 90º in + and -x direction

90 º in + and –y directions

Objective: Orientation Independent

Ambient Pressure:

Operation:

Threshold: 820 to 1050 mbar (corresponds to an altitude of approx. 5,000 ft) At ambient pressures below 900 mbar, a reversible performance decay of the high specific energy power source of 5% per every 50 mbar is permissible.

Objective: 400 to 1050 mbar

Transportation:

Threshold: 400 to 1050 mbar

Dust and Sand:

Complies with MIL-STD-810F, Method 510.4, Procedures 1,2,3

Water Immersion:

Threshold: The power manager must be submersible (up to 1ft of water). Other system components need to be packageable in dry bags for underwater submersion. There is no underwater operation requirement.

Water Resistance:

The system should be sufficiently watertight that it can operate in heavy rainfall.

Storage:

Temperature:

Threshold: -20 to 55 C

Objective: -40 to 65 C

Duration:

Threshold: 3 months

Objective: 12 months

Shock:

Threshold: MIL-STD-810F, Method 516.5, Procedure I and IV

Vibration:

Threshold: MIL-STD-810F, Method 514.5, Test for Categories 2, 4, 5, 7, 10, 20, 23 (per Table 514.5-I).

EMI/EMC:

MIL-STD-461E (Ground, Army Requirement, TableV) and MIL-STD-462D

Exterior Surface Temperature

Threshold: Not to exceed MIL-STD-1472F, Table XXI values for momentary and prolonged contact.

Communications Interface:

Threshold: SMBus compliant

Data:

Threshold: Total System Runtime, Battery Voltage, Battery Health Status, System Status, Error Log, Fuel Cartridge Level/Status, Subsystem Check, Air Filter Status.

(Data does not necessarily need to be displayed on units, but should be able to be viewed on standard computing platforms using USB interface)

Housings: Sand (33303). Please reference US Federal Standard 595B for color charts

Air Filter (if applicable): Easily accessible/replaceable.

Emissions: OSHA concentrations (per 1910.1000 Tables Z-1 and Z-2) for common exhausts such as methanol vapour, carbon monoxide, hydrogen (NTE LEL of 4% in exhaust), ect. Please reference http://www.osha.gov/SLTC/dieselexhaust/standards.html System Component Specifications:

Rechargeable Batteries

· 30 V nominal

· Upper voltage limit: 34 Volts

· Lower voltage limit: 20 Volts

· Energy storage:

· Threshold: 216 Wh (at C/2 discharge) and 8 Ah

· Objective: 340 Wh (at C/2 discharge) and 13 Ah

· Peak discharge capability: 16 Amps for 1 minute, repeatable every other minute for 10 minutes (a total of 5 minutes peak discharge)

· Integrated Charge electronics:

· Upper voltage cutoff (prevents overcharging)

· High Recharging Efficiency: above 93%

· Integrated Safety circuits

· Auto-reset low voltage cutoff/short circuit protection

· Auto-reset high temperature cutoff:

· Threshold: 65 C

· Objective: 75 C

· Non-resetting thermal fuse:

· Threshold: 75 C

· Objective: 85 C

· Cycle life to 75% original capacity:

· Threshold: 200 cycles

· Objective: 400 cycles

· Specific Energy:

· Threshold: 130 Wh/kg

· Objective: 200 Wh/kg

· SMBus compliant voltage and clock data output

· Must comply with DOT regulations for commercial transport on passenger aircraft

· Must fit inside a battery box whose inner dimensions are 2.4375” x 8.875’ x 5.625”

High Specific Energy Recharging Source

· Average Power

· Threshold: 25 W

· Objective: 50 W

· Specific Energy for continuous operation over 72 hours

· Threshold: 400 Wh/kg

· Objective: 600 Wh/kg

· Voltage: either a high (30-34V) output or a low (10-18V) output is acceptable

· If a low voltage output is selected, a suitable boost converter should be used in the power manager to step the voltage up to recharge the system batteries

· Voltage choice should hinge on most efficient operation of entire system

· Fuel Cartridges: If fuel is required, cartridges should be proposed that meet the following criteria

· Threshold: 8 hours of run time per cartridge

· Objective: 24 hours of run time

· Fuel Transport

· Threshold: Military transport as cargo

· Objective: Commercial transport as cargo

Lifetime:

Operation:

Threshold: 1500 operating hours before critical failure

Objective: 5000 operating hours before critical failure

Power Manager

· Two 22-34V inputs

· One for the system batteries (capable of max 16A current for 1 minute at a time)

· One for the high energy density recharging source (if a high voltage output is selected)

· One 30V output

· Capable of 10 Amp output for 1 minute at a time

· Two 15 V outputs

· Capable of a sum total of 6A continuous output

· One 10-18V input capable of accepting up to 10 Amps (This input should be capable of stepping voltage up to the high voltage bus at high efficiency)

· Connector specifications will be provided upon contract award

· State of Charge indicator: System should display a state of charge indication for the internal batteries. Recommend a state of charge indication that is not affected by current draw on the system. (For example, voltage indicators are adversely affected by the load the battery is under)

· All DC/DC conversions should be above 90% efficiency, with a goal of being above 95% efficiency over the current range they operate in.

· Data – Power manager should be able to track energy inputs and outputs from internal battery, and make predictions of runtime based on the current energy draw of the system.

PERIOD OF PERFORMANCE:

Technical Effort Complete: Twelve (12) Months After Effective Date of Award

Final Report Due: Four (4) Months After Completion of Technical Effort

ANTICIPATED FUNDING:

The funding profile shown below reflects the anticipated funding for the Small and Lightweight Portable Power Systems for Airmen Program. This funding profile is an estimate only and is not a promise of funding. Funding is uncertain and is subject to change. Changes in availability may occur as a result of the exercise of Government discretion and availability.

Funding in ($M)

COST SHARING:

Based on the potential for commercial application of this technology, cost sharing is encouraged.

DELIVERABLE ITEMS:

Data: In accordance with CDRLs identified below.

Hardware: Between two (2) and five (5) complete, field-testable hybrid power system prototypes are to be delivered. These prototypes must be stand-alone systems capable of being operated and tested in a military field environment.

APPLICABLE CDRLS (FOR CONTRACT ONLY):

Small and Lightweight Portable Power Systems for Airmen

APPLICABLE OTHER REQUIREMENTS

Security Classification

Unclassified

ITAR/Export Control PL 98-94

Does not apply for this effort

Notice to Foreign Owned Firms

No restrictions apply for this effort

Organizational Conflict of Interest

Does not apply for this effort

Government Furnished Property

No government furnished property is anticipated for this effort

Base Support

No base support is anticipated for this effort

Hazardous Material

This effort may involve the use of hazardous materials which include aviation fuel. Offerors should state their compliance with all applicable state and federal regulations.

Associate Contractor Provision

Does not apply for this effort

Computer and Network Access Requirements for Users and Equipment

Access to Government computer systems and government computer networks will not be provided

Power and Thermal Technologies for Air & Space (PTTAS) –

Small and Lightweight Portable Power Systems for Airmen Representations & Certifications for Contracts

I. NOTICE: The following solicitation provisions pertinent to this section are hereby incorporated by reference:

DEFENSE FEDERAL ACQUISITION REGULATION SUPPLEMENT SOLICITATION PROVISIONS

252.209-7001

DISCLOSURE OF OWNERSHIP OR CONTROL BY THE GOVERNMENT OF A

TERRORIST COUNTRY (SEP 2004)

II. NOTICE: The following solicitation provisions pertinent to this section are hereby incorporated in full text:

A. FEDERAL ACQUISITION REGULATION SOLICITATION PROVISIONS IN FULL TEXT

52.204-08 ANNUAL REPRESENTATIONS AND CERTIFICATIONS (JAN 2005)

(a)

(1) If the clause at 52.204-7, Central Contractor Registration, is included in this solicitation, paragraph (b) of this provision applies.

(2) If the clause at 52.204-7 is not included in this solicitation, and the offeror is currently registered in CCR, and has completed the ORCA electronically, the offeror may choose to use paragraph

(b) of this provision instead of completing the corresponding individual representations and certification in the solicitation. The offeror shall indicate which option applies by checking one of the following boxes:

[ ] (i) Paragraph (b) applies.

[ ] (ii) Paragraph (b) does not apply and the offeror has completed the individual representations and certifications in the solicitation.

(b) The offeror has completed the annual representations and certifications electronically via the

Online Representations and Certifications Application (ORCA) website at http://orca.bpn.gov. After reviewing the ORCA database information, the offeror verifies by submission of the offer that the representations and certifications currently posted electronically have been entered or updated within the last 12 months, are current, accurate, complete, and applicable to this solicitation (including the business size standard applicable to the NAICS code referenced for this solicitation), as of the date of this offer and are incorporated in this offer by reference (see FAR 4.1201); except for the changes identified below

[offeror to insert changes, identifying change by clause number, title, date]. These amended representation(s) and/or certification(s) are also incorporated in this offer and are current, accurate, and complete as of the date of this offer.

FAR Clause

Title

Date

Change

Any changes provided by the offeror are applicable to this solicitation only, and do not result in an update to the representations and certifications posted on ORCA.

B. DEFENSE FAR SUPP SOLICITATION PROVISIONS IN FULL TEXT

252.227-7017 IDENTIFICATION AND ASSERTION OF USE, RELEASE, OR DISCLOSURE

RESTRICTIONS (JUN 1995)

(a) The terms used in this provision are defined in following clause or clauses contained in this solicitation-

(1) If a successful offeror will be required to deliver technical data, the Rights in

Technical Data--Noncommercial Items clause, or, if this solicitation contemplates a contract under the Small Business Innovative Research Program, the Rights in Noncommercial Technical Data and

Computer Software--Small Business Innovative Research (SBIR) Program clause.

(2) If a successful offeror will not be required to deliver technical data, the Rights in

Noncommercial Computer Software and Noncommercial Computer Software Documentation clause, or, if this solicitation contemplates a contract under the Small Business Innovative Research Program, the

Rights in Noncommercial Technical Data and Computer Software--Small Business Innovative Research

(SBIR) Program clause.

(b) The identification and assertion requirements in this provision apply only to technical data, including computer software documentation, or computer software to be delivered with other than unlimited rights. For contracts to be awarded under the Small Business Innovative Research Program, the notification and identification requirements do not apply to technical data or computer software that will be generated under the resulting contract. Notification and identification is not required for restrictions based solely on copyright.

(c) Offers submitted in response to this solicitation shall identify, to the extent known at the time an offer is submitted to the Government, the technical data or computer software that the Offeror, its subcontractors or suppliers, or potential subcontractors or suppliers, assert should be furnished to the

Government with restrictions on use, release, or disclosure.

(d) The Offeror's assertions, including the assertions of its subcontractors or suppliers or potential subcontractors or suppliers shall be submitted as an attachment to its offer in the following format, dated and signed by an official authorized to contractually obligate the Offeror:

Identification and Assertion of Restrictions on the Government's Use, Release, or Disclosure of Technical Data or Computer Software.

The Offeror asserts for itself, or the persons identified below, that the Government's rights to use, release, or disclose the following technical data or computer software should be restricted:

Technical Data or

Basis for

Asserted

Name of Person

Computer Software

Assertion** Rights

Asserting to be Furnished

Category***

Restrictions****

With Restrictions*

*For technical data (other than computer software documentation) pertaining to items, components, or processes developed at private expense, identify both the deliverable technical data and each such item, component, or process. For computer software or computer software documentation identify the software or documentation.

**Generally, development at private expense, either exclusively or partially, is the only basis for asserting restrictions. For technical data, other than computer software documentation, development refers to development of the item, component, or process to which the data pertain. The Government's rights in computer software documentation generally may not be restricted. For computer software, development refers to the software. Indicate whether development was accomplished exclusively or partially at private expense. If development was not accomplished at private expense, or for computer software documentation, enter the specific basis for asserting restrictions.

***Enter asserted rights category (e.g., government purpose license rights from a prior contract, rights in

SBIR data generated under another contract, limited, restricted, or government purpose rights under this or a prior contract, or specially negotiated licenses).

****Corporation, individual, or other person, as appropriate.

*****Enter "none" when all data or software will be submitted without restrictions.

Date

Printed Name and Title

Signature

(End of identification and assertion)

(e) An offeror's failure to submit, complete, or sign the notification and identification required by paragraph (d) of this provision with its offer may render the offer ineligible for award.

(f) If the Offeror is awarded a contract, the assertions identified in paragraph (d) of this provision shall be listed in an attachment to that contract. Upon request by the Contracting Officer, the Offeror shall provide sufficient information to enable the Contracting Officer to evaluate any listed assertion.

252.247-7022 REPRESENTATION OF EXTENT OF TRANSPORTATION BY SEA (AUG 1992)

(a) The Offeror shall indicate by checking the appropriate blank in paragraph (b) of this provision whether transportation of supplies by sea is anticipated under the resultant contract. The term "supplies" is defined in the Transportation of Supplies by Sea clause of this solicitation.

(b) Representation. The Offeror represents that it-

____Does anticipate that supplies will be transported by sea in the performance of any contract or subcontract resulting from this solicitation.

____ Does not anticipate that supplies will be transported by sea in the performance of any contract or subcontract resulting from this solicitation.

(c) Any contract resulting from this solicitation will include the Transportation of Supplies by Sea clause. If the Offeror represents that it will not use ocean transportation, the resulting contract will also include the Defense FAR Supplement clause at 252.247-7024, Notification of Transportation of Supplies by Sea.

END OF CERTIFICATIONS FOR CONTRACTS

30 V

Equipment

15 V

Equipment

High Specific

Energy

Power Source

Energy Storage

(Battery Box)

Power

Manager

Energy

Harvesting