INTERLAC 665.pdf

A one pack alkyd gloss finish.PRODUCT

DESCRIPTION

For use as an easily maintained cosmetic finish coat on areas above the waterline.

For use at Newbuilding, Maintenance & Repair or On Board Maintenance.

INTENDED USES

CLB000-White, CLD260-Intl. Orange, CLK724-Storm Grey, CLL274-Red, CLL549-Signal Green, CLY999-Black ; and a wide range of colors.

48% ±3% (ISO 3233:1998)

1.6 mils dry (3.3 mils wet)

481 ft²/US gal at 1.6 mils dft, allow appropriate loss factors

Airless Spray, Brush, Conventional Spray, Roller

PRODUCT

INFORMATION

Volume Solids

Typical Film Thickness

Theoretical Coverage

Method of Application

Finish/Sheen High Gloss

Part B (Curing Agent) Not applicable

Flash Point Single Pack 104°F (Product produced and supplied in North America has a flashpoint of 106°F due to locally sourced solvents. There is no detrimental effect on product performance.)

Overcoating Data - see limitations Substrate Temperature

Color

Drying Information 41°F 50°F 77°F 95°F

Touch Dry [ISO 1517:73] 18 hrs 14 hrs 6 hrs 5 hrs

Hard Dry [ISO 9117:90] 62 hrs 48 hrs 24 hrs 12 hrs

Overcoated By

41°F 50°F 77°F 95°F

Min Max Min Max Min Max Min Max

Interlac 665 36 hrs ext 24 hrs ext 24 hrs ext 16 hrs ext

REGULATORY DATA VOC

Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in color and normal manufacturing tolerances.

420 g/lt (3.50 lb/US gal) as supplied (EPA Method 24) 364 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC)

Interlac 665 Alkyd Finish

Ref:161

Issue Date:7/7/2009

Marine Coatings

Interlac 665 Alkyd Finish

When used as part of an approved scheme, this material has the following certification:

• Fire Resistance - Surface Spread of Flame (WFR) - (IMO Resolution A653 (16))

• Fire Resistance - MSC61(67) Smoke & Toxicity (WFR)

• Fire Resistance - Marine Equipment Directive compliant

• Food Contact - Carriage of Grain (NOHA)

• Meets Petrobras Standard N-2492 - Alkyd Finish Gloss

• Fire Resistance - US Coast Guard Type Approval of Interior Finish

Consult your International Paint representative for details.

CERTIFICATION

Interlac 665 should only be applied over recommended anticorrosive primers. The primer to be used will depend upon vessel area, existing coatings, coating condition and application location. Typical primers include:

Interprime 198 Intertuf 203 Interprime 128 (in Europe) Interprime 222 (in South America) Interprime 234 (in North America) Interprime 538 (in Europe) Interlac 497 (applied as a sympathetically colored undercoat over Interprime 198)

In the Americas, Interlac 665 may also be applied over epoxy primers or epoxy tie coats. Consult International Paint.

Consult your International Paint representative for the system best suited for the surfaces to be protected.

SYSTEMS AND

COMPATIBILITY

Use in accordance with the standard Worldwide Marine Specifications.

All surfaces to be coated should be clean, dry and free from contamination.

High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning.

SURFACE

PREPARATIONS

NEWBUILDING/MAJOR REFURBISHMENT

Interlac 665 should always be applied over a recommended primer coating scheme. The primer surface should be dry and free from all contamination, and Interlac 665 must be applied within the overcoating intervals specified (consult the relevant product data sheet).Areas of breakdown, damage etc., should be prepared to the specified standard (e.g. Sa2½ (ISO 8501-1:2007) and primed prior to the application of Interlac 665

REPAIR

Repair corroded areas with an appropriate International Paint primer (consult the primer data sheet).

OBM

Interlac 665 should always be applied over a recommended primer coating scheme. The primer surface should be dry and free from all contamination, and Interlac 665 must be applied within the overcoating intervals specified (consult the relevant product data sheet).Areas of breakdown, damage etc., should be prepared to the specified standard (e.g. Sa2½ (ISO 8501-1:2007) and primed prior to the application of Interlac 665 Interlac 665 may be applied directly over aged Interlac 665 following thorough fresh water washing and degreasing provided the coating to be overcoated is in an intact and tightly adherent condition. Loose or flaking coatings should be removed back to a firm edge and Interlac 665 or an appropriate primer should be used to repair the area before application of the full coat.

Consult your International Paint representative for specific recommendations.

NOTE

For use in Marine situations in North America, the following surface preparation standards can be used:

SSPC-SP10 in place of Sa2½ (ISO 8501-1:2007)

Ref:161

This material is a one pack coating and should always be mixed thoroughly with a power agitator before application.

Suitable.

Suitable.

Not recommended. Use International GTA004 only in exceptional circumstances (max 5% by volume). DO NOT thin more than allowed by local environmental legislation.

International GTA004

In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation. In North America do so in accordance with instruction in ANSI/ASC Z49.1 "Safety in Welding and Cutting."

Recommended Tip Range 13-19 thou (0.33-0.48 mm) Total output fluid pressure at spray tip not less than 2010 psi (141 kg/cm²)

Use suitable proprietary equipment. Thinning may be required.

APPLICATION

Mixing

Airless Spray

Conventional Spray

Brush

Roller

Thinner

Cleaner

Welding

Work Stoppages and Cleanup

Thoroughly flush all equipment with International GTA004. All unused material should be stored in tightly closed containers. Partially filled containers may show surface skinning and/or a viscosity increase of the material after storage. Material should be filtered prior to use.

All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety & Environmental standards and regulations.

Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read and follow all precautionary notices on the Material Safety Data Sheet and container labels. If you do not fully understand these warnings and instructions or if you can not strictly comply with them, do not use this product. Proper ventilation and protective measures must be provided during application and drying to keep solvent vapor concentrations within safe limits and to protect against toxic or oxygen deficient hazards. Take precautions to avoid skin and eye contact (ie. gloves, goggles, face masks, barrier creams etc.) Actual safety measures are dependant on application methods and work environment.

EMERGENCY CONTACT NUMBERS:

USA/Canada - Medical Advisory Number 1-800-854-6813 Europe - Contact (44) 191 4696111. For advice to Doctors & Hospitals only contact (44) 207 6359191 R.O.W. - Contact Regional Office

SAFETY

Ref:161

Interlac 665 is not suitable for use on immersed areas.

Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local International Paint representative for specific recommendations.

Apply in good weather. Temperature of the surface to be coated must be at least 5°F above the dew point. For optimum application properties bring the material to 70°F-81°F, unless specifically instructed otherwise, prior to mixing and application. Unmixed material (in closed containers) should be maintained in protected storage in accordance with information given in the STORAGE Section of this data sheet. Technical and application data herein is for the purpose of establishing a general guideline of the coating application procedures. Test performance results were obtained in a controlled laboratory environment and International Paint makes no claim that the exhibited published test results, or any other tests, accurately represent results found in all field environments. As application, environmental and design factors can vary significantly, due care should be exercised in the selection, verification of performance and use of the coating.

In the overcoating data section 'ext' = extended overcoating period. Please refer to our Marine Painting Guide - Definitions and Abbreviations available on our website.

LIMITATIONS

UNIT SIZE Unit Size

Vol Pack

For availability of other unit sizes consult International Paint

20 lt 20 lt 20 lt

5 lt 5 lt 5 lt

5 US gal 5 US gal 5 US gal

1 US gal 1 US gal 5 US gal

UNIT SHIPPING WEIGHT Unit Size Unit Weight

20 lt 23.9 Kg

5 lt 6.01 Kg

5 US gal 49.5 lb

1 US gal 10 lb

Shelf Life 24 months minimum at 77°F. Subject to reinspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition

STORAGE

Consult International Paint.WORLDWIDE

AVAILABILITY

The information in this data sheet is not intended to be exhaustive: any person using the product for any purpose other than that specifically recommended in this data sheet without first obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at their own risk. All advice given or statements made about the product (whether in this data sheet or otherwise) is correct to the best of our knowledge but we have no control over the quality or the condition of the substrate or the many factors affecting the use and application of the product. Therefore, unless we specifically agree in writing to do so, we do not accept any liability at all for the performance of the product or for (subject to law) any loss or damage arising out of the use of the product. All products supplied and technical advice given are subject to our Conditions of Sale. You should request a copy of this document and review it carefully. The information contained in this data sheet is liable to modification from time to time in the light of experience and our policy of continuous development. It is the user's responsibility to check with their local International Paint representative that this data sheet is current prior to using the product.

IMPORTANT NOTE

and product names mentioned in this data sheet are trademarks of or are licensed to AkzoNobel.

© AkzoNobel, 2009 www.international-marine.com

Ref:161

Issue Date:7/7/2009 www.international-marine.com