25-0036-REQ_Plans-Electrical.pdf
PDF 2 MB Posted
- Attached to
- Cross Bayou Athletic Association Complex Improvements - Professional Design-Build Services (PID 004556B)
- Solicitation number
- 25-0036-RFQ-DB
- Issued by
- Pinellas County, Clewiston City, Florida
About this file
This is an electrical site plan document prepared by professional engineer Krista Marie Taylor for the Cross Bayou Athletic Association Complex Improvements project in Seminole, Florida, under Pinellas County's jurisdiction. The plans detail electrical infrastructure for a baseball park reconstruction project located at the corner of 102nd Avenue and 98th Street North. The design includes two proposed electrical panels (LP1 and LP2), three utility transformers (UTXFMR-1, UTXFMR-2, and UTXFMR-M1), and an 800-ampere main service disconnect rated at 277/480 volts with three-phase, four-wire configuration in a NEMA 3R exterior rated enclosure. The electrical work encompasses connections for sports lighting via Musco lighting poles, a scoreboard with 120-volt service, a batting cage pitching machine, monument signage with flashing beacons, and an existing well pump. The plans establish a steel channel support rack system for equipment mounting and specify grounding requirements using number 1/0 copper conductors in one-inch conduit connected to a five-eighths-inch by thirty-foot copper-clad ground triad with three-point configuration.
All work must comply with the Florida Building Code, the 2017 National Electrical Code, and applicable state and local amendments as determined through coordination with Duke Energy and Musco Lighting. The contractor is responsible for field verification of all device and equipment locations prior to rough-in installation, managing voltage drop calculations to maintain maximum cumulative five percent at the furthest downstream equipment, and providing arc flash and shock hazard signage in accordance with NEC Article 110.16, NFPA 70E, and OSHA requirements. The design specifies Schneider Electric as the manufacturer basis for all power distribution equipment and requires the contractor to provide trenching, backfill, conduit, conductors, and transformer pad installation in coordination with the utility company. The electrical plans were last revised on July 12, 2024, and form part of the comprehensive design-build service delivery for the professional reconstruction of the baseball facility.
View the file
Other files
Show all 49
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
ELECTRICAL SITE PLAN
SCALE: 1" = 30'1
PLAN NOTES
120V CONNECTION TO SCOREBOARD.
VERIFY EXACT LOCATION AND
REQUIREMENTS WITH OWNER AND
MANUFACTURER. PROVIDE
DISCONNECTING MEANS AS REQUIRED.
PROVIDE 120V GFCI PROTECTED DUPLEX
CONVENIENCE RECEPTACLE IN
WEATHERPROOF BACK-BOX WITH
LOCKABLE IN-USE COVER.
120V CONNECTION TO BATTING CAGE
PITCHING MACHINE. VERIFY EXACT
REQUIREMENTS WITH OWNER AND
MANUFACTURER. PROVIDE
DISCONNECTING MEANS AS REQUIRED.
120V CONNECTION TO MONUMENT SIGN.
VERIFY EXACT REQUIREMENTS WITH
OWNER AND MANUFACTURER. PROVIDE
DISCONNECTING MEANS AS REQUIRED.
CONNECTION TO EXISTING WELL PUMP.
VERIFY EXACT REQUIREMENTS. PROVIDE
DISCONNECTING MEANS AS REQUIRED.
CONTRACTOR SHALL VERIFY ALL SPORTS
LIGHTING LOCATIONS AND
REQUIREMENTS WITH FINAL LIGHTING
DESIGN.
T
UTXFMR-M1
PROPOSED PANEL LP1
LOCATION. SEE RISER
DIAGRAM FOR MORE
INFORMATION.
2 2
PROPOSED PANEL LP2 LOCATION.
SEE RISER DIAGRAM FOR MORE
INFORMATION.
MAINTENANCE
BUILDING #1
J
WELL
PUMP
10 10
10 10
LP2-6
MONUMENT SIGN
T
UTXFMR-1
PROPOSED UTILITY TRANSFORMER AND
METER LOCATION. SEE RISER DIAGRAM
FOR MORE INFORMATION.
PROPOSED UTILITY TRANSFORMER AND
METER LOCATION. SEE RISER DIAGRAM
FOR MORE INFORMATION.
UTXFMR-2
T
LP1-2
LP1-4
LP1-1
LP1-3
LP1-5
LP1-7
LP1-10
LP2-6
LP2-25
WP
WP
WP
WP
WP
WP
WP
MUSCO LIGHTING SERVICE TRANSFORMER, METER,
DISCONNECT SWITCH, DISTRIBUTION AND CONTROL PANEL
LOCATION. SEE RISER DIAGRAM FOR MORE INFORMATION.
RESTROOM/
CONCESSION
BUILDING #2
LP1-9
MUSCO LIGHTING
POLE LOCATION
(TYP.)
(TYP.)
MUSCO LIGHTING
POLE LOCATION
(TYP.)
(TYP.)
Krista Marie Taylor, P.E. #93024
3664 ROLLING HILLS LANE, APOPKA, FL 32712
407-703-3444 - www.TaylorAndTaylor.net
Feet 40200 10
07-12-2024
ELECTRICAL SITE PLAN
SCALE: 1" = 30'1
LP2-6
PROPOSED UTILITY TRANSFORMER AND
METER LOCATION. SEE RISER DIAGRAM
FOR MORE INFORMATION.
UTXFMR-2
T
LP1-1
LP2-6
LP2-1
LP2-3
LP2-9
LP2-14
LP2-16
WP
WP
WP
WP
RESTROOM/
CONCESSION
BUILDING #2
LP2-12
MUSCO LIGHTING
POLE LOCATION
(TYP.)
(TYP.)
PLAN NOTES
120V CONNECTION TO SCOREBOARD.
VERIFY EXACT LOCATION AND
REQUIREMENTS WITH OWNER AND
MANUFACTURER. PROVIDE
DISCONNECTING MEANS AS REQUIRED.
PROVIDE 120V GFCI PROTECTED DUPLEX
CONVENIENCE RECEPTACLE IN
WEATHERPROOF BACK-BOX WITH
LOCKABLE IN-USE COVER.
120V CONNECTION TO BATTING CAGE
PITCHING MACHINE. VERIFY EXACT
REQUIREMENTS WITH OWNER AND
MANUFACTURER. PROVIDE
DISCONNECTING MEANS AS REQUIRED.
120V CONNECTION TO FLASHING
BEACONS/SIGN. VERIFY EXACT
REQUIREMENTS WITH OWNER AND
MANUFACTURER.
CONNECTION TO EXISTING WELL PUMP.
VERIFY EXACT REQUIREMENTS. PROVIDE
DISCONNECTING MEANS AS REQUIRED.
CONTRACTOR SHALL VERIFY ALL SPORTS
LIGHTING LOCATIONS AND
REQUIREMENTS WITH FINAL LIGHTING
DESIGN.
Krista Marie Taylor, P.E. #93024
3664 ROLLING HILLS LANE, APOPKA, FL 32712
407-703-3444 - www.TaylorAndTaylor.net
07-12-2024
ELECTRICAL RISER DIAGRAM @ MUSCO LIGHTING DISTRIBUTION
SCALE: NONE1
800A
SERVICE
DISCONNECT
277/480V 3Ø-4W
NEMA 3R
EXTERIOR ELECTRICAL EQUIPMENT RACK @
MUSCO LIGHTING SERVICE
SERVICE
METER
UTILITY
TRANSFORMER
UTXFMR-1
120/240V 1Ø
SECONDARY
MAINTENANCE
BLDG. #1
PANEL LP1
200A MCB
120/240V
1Ø,3W
NEMA 1
ELECTRICAL RISER DIAGRAM @ BUILDING #1
SCALE: NONE2
ELECTRICAL RISER DIAGRAM @ BUILDING #2
SCALE: NONE3
UTILITY
TRANSFORMER
UTXFMR-M1
480V-3Ø
SECONDARY
TO UTILITY
PRIMARY
TO UTILITY
PRIMARY
MUSCO
LIGHTING
DISTRUBUTION
PANEL MLDP
800A
MLO
277/480V 3Ø-4W
NEMA 3R
MUSCO
LIGHTING
CONTROL
PANEL
MUSCO
LIGHTING
CONTROL
PANEL
MUSCO
LIGHTING
CONTROL
PANEL
NEMA 3R
T
6 6 6
GENERAL NOTESRISER DIAGRAM NOTES #
A. ALL WORK SHALL COMPLY WITH THE FLORIDA BUILDING CODE AND THE 2017
NATIONAL ELECTRIC CODE, AS WELL AS STATE AND LOCAL CODES AND/OR
AMENDMENTS.
B. DO NOT SCALE ELECTRICAL DRAWING FOR ANY DIMENSIONS.
C. PROVIDE GROUNDING AND BONDING PER NEC 250.
D. ALL CIRCUITS NOT SIZED ON DRAWING SHALL BE INSTALLED TO MEET MINIMUM SIZE
REQUIRED BY NEC. ALL CONDUCTORS SHALL HAVE AN EQUIPMENT GROUND WIRE
SIZED PER NEC.
E. FIELD VERIFY EXACT LOCATION OF ALL DEVICES AND EQUIPMENT PRIOR TO
ROUGH-IN.
F. CONTRACTOR SHALL PROVIDE PROVIDE ARC FLASH / SHOCK HAZARD SIGNAGE FOR
ALL SWITCHGEAR IN ACCORDANCE WITH NEC ARTICLE 110.16, NFPA 70E, AND OSHA.
INCLUDE ALL INFORMATION PER LATEST REQUIREMENTS INCLUDING NOMINAL
VOLTAGE, AVAILABLE FAULT CURRENT, CLEARING TIME FOR DEVICES, APPROACH
BOUNDARIES, AND REQUIRED LEVEL OF PPE.
G. PER NEC 110.24 SERVICE EQUIPMENT IN OTHER THAN DWELLING UNITS SHALL BE
LEGIBLY MARKED IN THE FIELD WITH THE MAXIMUM AVAILABLE FAULT CURRENT. THE
FIELD MARKING(S) SHALL INCLUDE THE DATE THE FAULT CURRENT CALCULATION
WAS PERFORMED AND BE OF SUFFICIENT DURABILITY TO WITHSTAND THE
ENVIRONMENT INVOLVED. WHEN MODIFICATIONS TO THE ELECTRICAL INSTALLATION
OCCUR THAT AFFECT THE MAXIMUM AVAILABLE FAULT CURRENT AT THE SERVICE,
THE MAXIMUM AVAILABLE FAULT CURRENT SHALL BE VERIFIED OR RECALCULATED AS
NECESSARY TO ENSURE THE SERVICE EQUIPMENT RATINGS ARE SUFFICIENT FOR
THE MAXIMUM AVAILABLE FAULT CURRENT AT THE LINE TERMINALS OF THE
EQUIPMENT. THE REQUIRED FIELD MARKING(S) IN 110.24(A) SHALL BE ADJUSTED TO
REFLECT THE NEW LEVEL OF MAXIMUM AVAILABLE FAULT CURRENT.
H. THE MANUFACTURER BASIS OF DESIGN FOR ALL POWER DISTRIBUTION EQUIPMENT IS
SCHNEIDER ELECTRIC.
I. INCREASE FEEDER CONDUCTOR AND CONDUIT SIZES (AS REQUIRED WHEN FINAL
FEEDER ROUTE IS ESTABLISHED) IN ORDER TO MAINTAIN A MAXIMUM CUMULATIVE
VOLTAGE DROP OF FIVE (5) PERCENT AT THE FURTHEST DOWNSTREAM EQUIPMENT.
VOLTAGE DROP SHALL BE DISTRIBUTED AMONGST FEEDERS AND BRANCH CIRCUITS
IN ACCORDANCE WITH FLORIDA ENERGY CODE REQUIREMENTS. WHERE EQUIPMENT
IS UNABLE TO ACCOMMODATE UPSIZED CONDUCTORS, PROVIDE LUG KITS (AS
REQUIRED). WHERE LUG KITS ARE UNABLE TO ACCOMMODATE UPSIZED
CONDUCTORS, SPLICE AND TRANSITION TO A SMALLER CONDUCTOR SIZE AT THE
POINT OF TERMINATION VIA AN AUXILIARY GUTTER, PULL BOX, WIREWAY, OR OTHER
SUITABLE DEVICE.
3 3 3
FRONT SIDE OF EQUIPMENT RACK REAR SIDE OF EQUIPMENT RACK
20'-0"
MIN
SERVICE
METER
CT CABINET
PANEL LP2
100A MCB
120/240V
1Ø,3W
NEMA 1
SERVICE
METER
UTILITY
TRANSFORMER
UTXFMR-2
120/240V 1Ø
SECONDARY
TO UTILITY
PRIMARY
CONCESSION /
RESTROOM BLDG. #2
SPD
SPD
SPD
2 2
FINISHED FLOOR
FINISHED FLOORGRADE
GRADEGRADE
FEEDER SCHEDULE #
NEMA 3R
S3
S1
SVC. ENTRANCE FEEDER SCHEDULE S#
1. UTILITY COMPANY PAD MOUNTED TRANSFORMER. CONTRACTOR SHALL
COORDINATE EXACT SERVICE LOCATION AND REQUIREMENTS WITH
DUKE ENERGY. PROVIDE TRENCHING, BACKFILL, CONDUIT,
CONDUCTORS AND TRANSFORMER PAD AS REQUIRED.
2. UTILITY METER AND/OR CT CABINET. VERIFY ALL REQUIREMENTS WITH
DUKE ENERGY.
3. PROVIDE STEEL CHANNEL SUPPORT RACK FOR ELECTRICAL
EQUIPMENT SIZED AS REQUIRED. POSTS MUST BE SPACED TO PROVIDE
STABLE MOUNTING FOR EQUIPMENT. RACK CROSS-MEMBERS MUST BE
STAINLESS STEEL FOR MOUNTING OF THE ELECTRICAL ENCLOSURES.
USE CHANNEL SUPPORT SYSTEM FOR ALL RACK MOUNTED EQUIPMENT.
EXTERIOR UNITS SHALL BE THOROUGHLY INSPECTED AFTER
INSTALLATION.
4. PROVIDE #1/0 CU GROUND IN 1" CONDUIT TO 5/8"x30' CU CLAD GROUND
THREE POINT GROUND TRIAD.
5. STEP-DOWN TRANSFORMER 1kVA 277-120/240V & 20A ENCLOSED
CIRCUIT BREAKER FOR LIGHTING CONTROL 120V CONTROL CIRCUIT.
6. CONTRACTOR SHALL VERIFY EXACT REQUIREMENTS FOR MUSCO
LIGHTING DISTRIBUTION AND CONTROL EQUIPMENT WITH MUSCO
LIGHTING FINAL DESIGN DOCUMENTS. ADJUST EQUIPMENT RACK AND
ALL RELATED COMPONENTS AS REQUIRED.
7. PROVIDE SERVICE GROUND PER NEC 250. SEE DETAIL.
800A: (2) SETS OF (4) #600, #1/0 GRD. IN EACH OF 3-1/2" C.
(2) #12, #12 GRD. 3/4" C.
S1. 800A: (2) SETS OF (4) #600, IN EACH OF 3-1/2" C.
S2. 100A: (3) #3, 1-1/4" C.
S3. 200A: (4) #1/0, 2" C.
S2
S1 1
ECB
(1) #12, 3/4" C.(1) #4 GEC, 3/4" C.
(1) #6 GEC , 3/4" C.
CT CABINET SERVICE
METER
GRADE
Krista Marie Taylor, P.E. #93024
3664 ROLLING HILLS LANE, APOPKA, FL 32712
04/19/202407-12-2024
Krista Marie Taylor, P.E. #93024
3664 ROLLING HILLS LANE, APOPKA, FL 32712
04/19/202407-12-2024
| E-01 |
| Sheets and Views |
| E-01 |
| E-02 |
| Sheets and Views |
| E-02 |
| E-03 |
| E003 |
| E003 |
| E-04 |
| E004 |
| E004 |
File details come from the government source that posted it. Updated .