14f- 578-20-002 100percent Bid Drawings -Part 6.pdf

ELECTRICAL GENERAL NOTES GENERAL NOTES - DEMOLITION

NOTES:

1. ALL DIMENSIONS ARE CONSIDERED FROM FINISHED FLOOR AND, UNLESS NOTED OTHERWISE, SHALL NOT VARY. RAISED FLOORS SHALL BE

CONSIDERED FINISHED FLOOR.

2. ALL DIMENSIONS SHALL BE COORDINATED WITH ARCHITECTURAL DETAILS AND MAY BE ADJUSTED TO CONFORM WITH ARCHITECTURAL

REQUIREMENTS AS LONG AS NO CODE RESTRICTION IS VIOLATED.

3. OUTLETS INSTALLED LOWER THAN 15" AFF (FORWARD REACH) AND 9" AFF (SIDE REACH) ARE IN VIOLATION OF ADA.

AS NOTED ON DRAWINGS.

EXCEPTION: 44" MAXIMUM TO TOP ABOVE COUNTERS WHICH ARE

20"-25"D.

16" TO BOTTOM OF BOX OR AS NOTED ON DRAWINGS. EXCEPTION: 44"

MAXIMUM TO TOP ABOVE COUNTERS WHICH ARE 20"-25"D.

48" TO HIGHEST OPERABLE PART (SIDE OR FORWARD ACCESS).

16" TO BOTTOM OF BOX.

EXCEPTION: 44" MAXIMUM TO TOP ABOVE COUNTERS WHICH ARE

20"-25"D.

90" TO CENTERLINE OF SIGN OR CENTERED IN WALL

48" TO CENTERLINE OF BOX MINIMUM (TOILETS).

66" TO CENTERLINE OF BOX MAXIMUM (SHOWERS -

LOCATED OUT OF SPRAY AREA).

AREA BETWEEN TOP OF DOOR AND CEILING.

80" TO CENTERLINE OF DEVICE OR 6" BELOW CEILING, WHICHEVER IS

LOWER.

48" TO CENTERLINE OF BOX.

EXCEPTION: 44" MAXIMUM TO TOP ABOVE COUNTERS

WHICH ARE 20"-25"D.

80" TO BOTTOM OF DEVICE OR NOT MORE THAN 96" TO TOP.FIRE ALARM VISUAL ONLY DEVICE OR A

COMBINATION AUDIBLE AND VISUAL DEVICE

NOT LESS THAN 90" TO TOP OR 6" BELOW CEILING, WHICH

EVER IS HIGHER.

48" TO HIGHEST OPERABLE PART - NOT MORE THAN 5'-0" FROM

EXIT.

54" TO DIAL CENTER (NON-ACCESSIBLE).

48" TO HIGHEST OPERABLE PART (ACCESSIBLE).

12" CEILING TO CENTERLINE OR 7'-0" TO CENTERLINE IF CEILING IS OVER

8'-0".

DISCONNECT SWITCHES, MOTOR STARTERS,

MOTOR PUSH BUTTON STATIONS

MOUNTING HEIGHTSDEVICE

"A" FT.

LIGHT SWITCHES, WALL MOUNTED OCCUPANCY

SENSORS

WALL MOUNTED EXIT SIGNS

CEILING MOUNTED EXIT SIGNS

RECEPTACLES

SPECIAL OUTLETS OR

RECEPTACLES

PLUGMOLD OR WIREMOLD

CLOCK OUTLETS

DATA/COMMUNICATION OR TELEPHONE OUTLETS

TELEPHONE OUTLETS - WALL TYPE

FIRE ALARM MANUAL PULL STATIONS

FIRE ALARM AUDIBLE ONLY DEVICE

WALL MOUNTED REMOTE INDICATOR LIGHT

AREA OF REFUGE TELEPHONE

CALL FOR AID SWITCH WITH PULL CHAIN TO FLOOR

CARD READER

INTERCOM STATION

SOUND SYSTEM VOLUME CONTROL

MICROPHONE OUTLETS

THERMOSTATS

TEMPERATURE/HUMIDITY SENSORS 60" TO CENTER LINE OF BOX.

54" TO HIGHEST OPERABLE PART (SIDE ACCESS).

48" HIGHEST OPERABLE PART (FORWARD ACCESS).

16" TO BOTTOM OF BOX.

54" TO HIGHEST OPERABLE PART (SIDE ACCESS).

48" HIGHEST OPERABLE PART (FORWARD ACCESS).

54" TO HIGHEST OPERABLE PART (SIDE ACCESS).

48" HIGHEST OPERABLE PART (FORWARD ACCESS).

SAME AS TELEPHONE - ACCESSIBLE.

16" TO BOTTOM OF BOX.

80" TO BOTTOM FIXTURE.

60" TO CENTERLINE.

IF DISTANCE (A+B) IN FEET IS:

(SEE DIAGRAMAT RIGHT)

FOR 120V-20A BRANCH CIRCUITS ONLY (UNLESS NOTED OTHERWISE)

USE COPPER WIRE IN METALLIC CONDUIT,

AWG SIZE AS FOLLOWS ON ENTIRE CIRCUIT

AND SIZE CONDUIT ACCORDINGLY.

#12 AWG (MIN.)

#10 AWG

#8 AWG

#6 AWG (MAX.)

PANELBOARD

* RECEPTACLE OR LIGHTING LOAD

PANELBOARD

*LAST ON

CIRCUIT.

#12 AWG (MIN.)

#10 AWG

#8 AWG

#6 AWG (MAX.)

0' TO 100'

100' TO 175'

175' TO 300'

300' TO 450'

*FIRST ON

CIRCUIT.

"B" FT.

"A" FT.

0' TO 250'

250' TO 400'

400' TO 700'

700' TO 1000'

MOUNTING HEIGHTS FOR ELECTRICAL DEVICES

WIRE SIZING TABLE

SEE ALL PROJECT GENERAL NOTES AND OTHER REQUIREMENTS

INCLUDING THE LIFE SAFETY AND INFECTION CONTROL

REQUIREMENTS LOCATED WITHIN THE GENERAL DRAWINGS SECTION.

COMPLY WITH ALL REQUIREMENTS AS THEY ARE A DIRECT PART OF

THIS SECTION AND AS IF THEY WERE DIRECTLY INCLUDED AND

PROVIDED BELOW.

EQUIVALENCY SUBSTITUTIONS: THE "BASIS OF DESIGN (BOD)

PROTOCOLS": IS TO BE FOLLOWED FOR ALL EQUIPMENT, MATERIAL

AND ASSEMBLIES SPECIFIED AND DETAILED THROUGHOUT ALL

DRAWINGS AND SPECIFICATION SECTIONS, WHETHER THE BOD

DESIGNATE IS SPECIFICALLY REFERENCED THEREIN OR NOT. SEE THE

GENERAL DRAWINGS SECTION FOR THE FULL BOD EQUIVALENCY

SUBSTITUTION REQUIREMENTS AND PROTOCOLS TO BE FOLLOWED.

1. CODES

THE WORK SHALL COMPLY WITH ALL APPLICABLE LOCAL,

MUNICIPAL, STATE, NATIONAL CODES, AND ALL VA APPLICABLE

DESIGN MANUALS STANDARDS REQUIREMENTS. WHERE THE

CONSTRUCTION DOCUMENTS INDICATE MORE RESTRICTIVE

REQUIREMENTS THE CONSTRUCTION DOCUMENTS SHALL

GOVERN. HOWEVER, THE CONSTRUCTION DOCUMENTS SHALL

NOT BE INTERPRETED AS AUTHORITY TO VIOLATE ANY CODE OR

REGULATION.

ALL WORK, MATERIAL, AND EQUIPMENT SHALL COMPLY WITH

ALL REQUIREMENTS OF THE LATEST EDITIONS AND INTERIM

AMENDMENTS OF THE NATIONAL ELECTRICAL CODE (N.E.C.),

NATIONAL ELECTRICAL SAFETY CODE, OSHA, AND ALL

APPLICABLE FEDERAL, STATE, AND LOCAL LAWS AND

ORDINANCES ALONG WITH ALL DESIGN CRITERIA STD AND

REQUIREMENTS. ALL ELECTRICAL EQUIPMENT PROVIDED

UNDER THIS CONTRACT SHALL BE NEW (UNLESS OTHERWISE

NOTED) AND SHALL BEAR THE MARK OF NATIONALLY

RECOGNIZED TESTING LABORATORY. ALL EQUIPMENT OF THE

SAME TYPE AND CAPACITY SHALL BE BY THE SAME

MANUFACTURER.

2. DRAWINGS AND SPECIFICATIONS

THE CONTRACTOR SHALL BE RESPONSIBLE FOR READING AND

COMPLYING WITH BOTH THE DRAWINGS AND SPECIFICATIONS.

IN THE EVENT OF A CONFLICT OR INCONSISTENCY BETWEEN

THE DRAWINGS, NOTES, SPECIFICATIONS, OR CODES, THE

REFERENCE WHICH PROVIDES THE MORE COMPLETE OR

HIGHER STANDARD SHALL PREVAIL.

CONTRACTOR SHALL REVIEW ENTIRE SET OF CONTRACT

DOCUMENTS: INCLUDING BUT NOT NECESSARILY LIMITED TO

ALL ARCHITECTURAL, ALL STRUCTURAL, ALL MECHANICAL, ALL

ELECTRICAL, ALL PLUMBING, AND ENTIRE SPECIFICATIONS.

CONTRACTOR SHALL ACKNOWLEDGE AND INCLUDE IN THE

SCOPE OF WORK (CONTRACT) ALL CONDITIONS PERTINENT TO

THE COMPLETION OF THE ELECTRICAL WORK. CONTRACTOR

SHALL FULLY COORDINATE ELECTRICAL WORK WITH THE

INSTALLATION OF WORK BY ALL OTHER TRADES AND MAKE

NECESSARY FIELD ADJUSTMENTS AS REQUIRED TO

ACCOMMODATE THE ELECTRICAL INSTALLATION. ALL OF THE

ABOVE SHALL BE INCLUDED IN THE BASE SCOPE OF WORK AT

NO ADDITIONAL COST TO THE VA.

3. INTERPRETATION OF THE DOCUMENTS

CAREFULLY COMPARE THE DRAWINGS AND SPECIFICATIONS,

CHECKING MEASUREMENTS AND CONDITIONS UNDER WHICH

THIS INSTALLATION IS TO BE MADE. FOR CLARIFICATION

BETWEEN VARIOUS DRAWINGS, BETWEEN DRAWINGS OR

SPECIFICATION, OR BETWEEN SECTIONS OF THE

SPECIFICATION, THE MATTER SHALL BE REFERRED TO THE COR

BEFORE ANY WORK IS EXECUTED. THE CONTRACTOR SHALL

STATE IN THEIR PROPOSAL ANY EXCEPTIONS NECESSARY TO

MAKE THIS A COMPLETE, READY TO USE INSTALLATION. IF NOT

STATED IN THE BID, IT WILL NOT BE CONSIDERED EXTRA.

ALL WORK SHALL BE DONE IN ACCORDANCE WITH THE

CONTRACT DOCUMENTS, IN A NEAT AND WORKABLE MANNER

CONSISTENT WITH RECOGNIZED GOOD PRACTICE, AND SHALL

BE SUBJECT TO THE APPROVAL OF THE VA.

ANY CHANGES TO THE CONTRACT REQUIREMENTS MUST BE

APPROVED PRIOR TO CONSTRUCTION. THE CONTRACTOR

SHALL KEEP UP-TO-DATE DRAWINGS, ON-SITE, AVAILABLE,

INCLUDING ALLOWABLE DEVIATIONS FROM THE CONTRACT

DRAWINGS.

4. ELECTRICAL DRAWINGS

THE ELECTRICAL DRAWINGS ARE DIAGRAMMATIC AND SHALL

NOT BE SCALED. THE CONTRACTOR SHALL DETERMINE THE

EXACT LOCATION OF ALL DOORS, WALLS, FURNITURE,

EQUIPMENT, ETC. THE LOCATION OF RACEWAY SYSTEM

COMPONENTS IS SCHEMATIC. THE EXACT LOCATION OF

RACEWAY SYSTEM COMPONENTS SHALL BE DETERMINED BY

THE CONTRACTOR IN THE FIELD. THE CONTRACTOR SHALL

CONFIRM THE ACTUAL EQUIPMENT TO BE SUPPLIED FOR THIS

PROJECT, AND VERIFY CLEARANCES AND ROUGH-INS PRIOR TO

STARTING WORK.

5. SITE EXAMINATION

BEFORE SUBMITTING A BID, THE CONTRACTOR SHALL VISIT THE

SITE AND MAKE A THOROUGH SURVEY OF THE EXISTING

CONDITIONS. THIS VISIT SHALL ONLY BE ALLOWED AS PER THE

VA SCHEDULED WALKTHROUGH AND THE SUBMISSION OF A BID

WILL BE CONSTRUED AS EVIDENCE THAT SUCH A VISIT HAS

BEEN MADE. NO CONSIDERATION OR ALLOWANCE WILL BE

GRANTED FOR FAILURE TO VISIT THE SITE OR FOR LATER

CLAIMS FOR LABOR, EQUIPMENT, MATERIALS REQUIRED, OR

FOR DIFFICULTIES ENCOUNTERED WHICH COULD HAVE BEEN

FORESEEN HAD SUCH VISIT BEEN MADE.

CONTRACTOR SHALL CAREFULLY EXAMINE THE DRAWINGS AND

SPECIFICATIONS, VISIT THE SITE OF THE WORK, AND FULLY

INFORM HIM/HER SELF AS TO ALL CONDITIONS AND MATTERS

THAT CAN, IN ANY WAY, AFFECT THE WORK OR THE COST

THEREOF, SHOULD THIS CONTRACTOR FIND DISCREPANCIES IN,

OR OMISSIONS FROM, THE DRAWINGS, SPECIFICATIONS OR

OTHER DOCUMENTS OR BE IN DOUBT AS TO THEIR MEANING,

NOTIFY THE VA AT ONCE, IN WRITING, OF ANY DISCREPANCIES

BETWEEN EXISTING CONDITIONS AND NEW WORK, OR BETWEEN

ELECTRICAL WORK AND THE WORK OF OTHER TRADES AND

OBTAIN CLARIFICATION PRIOR TO SUBMITTING ANY BID. LACK

OF SUCH NOTIFICATION SHALL BE CONSTRUED TO INDICATE NO

DISCREPANCIES OR CONFLICTS EXIST. ADDITIONAL

COMPENSATION WILL NOT BE GRANTED AFTER AWARD OF

CONTRACT FOR ANY WORK REQUIRED TO COMPLY WITH THESE

REQUIREMENTS.

6. COORDINATION WITH OTHER TRADES

THE ELECTRICAL CONTRACTOR SHALL OBTAIN A COMPLETE SET

OF ARCHITECTURAL AND ENGINEERING DOCUMENTS AND

COORDINATE WITH MECHANICAL, PLUMBING, ARCHITECTURAL,

AND OTHER TRADES FOR EXACT DIMENSIONS, CLEARANCES,

ROUGH-IN LOCATIONS, AND OTHER ADDITIONAL SCOPE OF

WORK THAT MAY NOT BE SHOWN ON THE ELECTRICAL PLANS.

THE ELECTRICAL CONTRACTOR SHALL BE RESPONSIBLE FOR

ALL 120 VOLT (AND HIGHER) AC POWER TO OTHER TRADES

EQUIPMENT AND HARDWARE. THIS SHALL INCLUDE, BUT NOT BE

LIMITED TO, CONTROLS, FIRE AND SECURITY SYSTEMS,

MOTORIZED DOORS, DAMPERS, LIFTS, AND OTHER SYSTEMS.

UNLESS SPECIFICALLY NOTED OTHERWISE ON THE ELECTRICAL

PLANS, THE ELECTRICAL CONTRACTOR SHALL FURNISH ALL

SAFETY DISCONNECT SWITCHES TO MECHANICAL EQUIPMENT.

THE CONTRACTOR SHALL CHECK ALL ARCHITECTURAL,

STRUCTURAL, AND MECHANICAL TRADES WORK FOR POSSIBLE

INTERFERENCE CAUSED BY CONDITIONS IN THE FIELD BEFORE

THE BID IS MADE. NO ALLOWANCE SHALL SUBSEQUENTLY BE

MADE TO THE CONTRACTOR BY REASON OF HIS/HER FAILURE

TO HAVE MADE SUCH EXAMINATIONS OR OF ANY ERROR OF

HIS/HER PART.

7. THE ELECTRICAL CONTRACTOR IS RESPONSIBLE FOR

SCHEDULING DELIVERY, RECEIVING, UNLOADING, UNCRATING,

STORING SETTING IN PLACE, AND PROTECTING FROM DAMAGE,

VANDALISM, THEFT OR WEATHER DURING CONSTRUCTION FOR

ALL NEW EQUIPMENT FURNISHED BY THE ELECTRICAL

CONTRACTOR.

CONTRACTOR SHALL PAY ALL PERMIT FEES, PLAN REVIEW

FEES, LICENSE FEES, INSPECTIONS AND TAXES APPLICABLE TO

THIS DIVISION IF NECESSARY. (FEDERAL GOVERNMENT IS NOT

SUBJECT TO LOCAL PERMITS OR FEE FOR THE PROJECT).

8. FIRE STOPPING

ALL PENETRATIONS IN WALL, FLOOR OR CEILINGS SHALL BE

SUITABLY CLOSED UP AND SEALED WITH AN INTUMESCENT FIRE

STOPPING COMPOUND LISTED IN THE MOST RECENT FACTORY

MUTUAL RESEARCH CORPORATION (FMRC) APPROVAL GUIDE.

FIRE STOPPING PRODUCTS SHALL BE MANUFACTURED BY 3M

CO OR APPROVED EQUAL.

9. PAINTING

ALL NEWLY INSTALLED EXPOSED PIPING SHALL BE PAINTED TO

MATCH THE EXISTING ADJACENT WALL OR CEILING SURFACE.

10. VA FURNISHED EQUIPMENT

EQUIPMENT THAT WILL BE FURNISHED BY THE VA SHALL BE

INDICATED ON A SEPARATE SCHEDULE. THE CONTRACTOR

SHALL COORDINATE WITH THE VA FOR DELIVERY SCHEDULES.

THE CONTRACTOR IS TO ASSUME THAT ON SITE STORAGE MAY

NOT BE AVAILABLE WHEN COORDINATING DELIVERY OF

EQUIPMENT. THE CONTRACTOR, IN COORDINATION WITH THE

COR, WILL INSPECT THE DELIVERY FOR ACCURACY AND

SHIPMENT DAMAGE AND ACCEPTING THE EQUIPMENT. THE

CONTRACTOR SHALL BE RESPONSIBLE TO STORE, PROTECT,

AND ULTIMATELY INSTALL THE EQUIPMENT.

11. ELECTRICAL SERVICE DISRUPTIONS

ANY WORK INVOLVING A TASK WHICH EXPOSES ACTIVE BUS

SHALL BE PERFORMED AFTER HOURS (11:00PM TO 5:00AM). THIS

RESTRICTION INCLUDES REMOVING THE COVER FROM ANY

PANEL BOARD, SWITCHBOARD, M.C.C. ETC. ALL WORK WHICH

EXPOSES ACTIVE BUS REQUIRES A WRITTEN NOTIFICATION TO

THE COR WHICH WILL OUTLINE THE METHOD OF PROCEDURE

FOR THE WORK. THE CONTRACTOR SHALL PROVIDE A MINIMUM

OF 2 WEEKS NOTICE TO THE COR BEFORE WORKING ON ANY

ENERGIZED ELECTRICAL SYSTEM. ALL POWER DISRUPTION

SHALL OCCUR AT TIMES AND OF DURATIONS ACCEPTABLE TO

THE COR.

12. EQUIPMENT

ALL MATERIALS AND EQUIPMENT USED IN THIS INSTALLATION

SHALL BE NEW, AND HAVE THE APPROPRIATE UL LISTING AND

LABEL.

THE CONTRACTOR SHALL FURNISH ALL LABOR, MATERIAL,

TOOLS, EQUIPMENT SERVICES, AND ACCESSORIES FOR

COMPLETE INSTALLATION OF ALL ELECTRICAL WORK AS NOTED.

ITEMS OMITTED FROM EITHER THE SPECIFICATIONS OR THE

DRAWINGS, BUT SHOWN OR DESCRIBED IN ONE OR THE OTHER,

AND ITEMS NECESSARY TO MAKE THE ELECTRICAL SYSTEM

COMPLETE AND WORKABLE SHALL FORM A PART OF THE WORK.

13. MISCELLANEOUS SUPPORTING MEMBERS

ALL ANGLES CHANNELS, AND OTHER MISCELLANEOUS STEEL,

BOLTS, RODS, ETC. REQUIRED TO SUPPORT LUMINAIRE,

CONDUIT, RACEWAY, LADDER TRAY, OR OTHER ELECTRICAL

EQUIPMENT OR DEVICES SHALL BE FURNISHED AND INSTALLED

BY THE CONTRACTOR.

ANY MENTION OF A SPECIFIC VOLTAGE ON THE ELECTRICAL

DRAWINGS SHALL NOT RELIEVE THE ELECTRICAL CONTRACTOR

OF THE RESPONSIBILITY TO VERIFY THE VOLTAGE PRIOR TO

PURCHASING OR ROUGH-IN WORK.

14. DISTRIBUTION PANELS AND PANELS BOARDS

ALL DISTRIBUTION PANELS AND PANEL BOARDS SHALL BE

PROVIDED WITH TYPEWRITTEN DIRECTORIES. SEE PANEL

SCHEDULES ON THE DRAWINGS AND SPECIFICATION FOR

COMPLETE IDENTIFICATION AND LABELING REQUIREMENTS. ALL

DISTRIBUTION PANELS AND PANEL BOARDS SHALL BE LABELED

ON THE PANEL CABINET WITH THE PANEL NAME AND THE

POWER SOURCE FEEDING THE PANEL AS PER THE ELECTRICAL

ONE LINE. ALL PANELS AND PANEL BOARDS SHALL BE PROVIDED

WITH HINGED DOOR WITH LOCK AND KEY.

15. SAFETY

THE CONTRACTOR SHALL TAKE ALL STEPS NECESSARY TO

ENSURE THE SAFETY OF THE VA'S EMPLOYEES, BUILDING

EMPLOYEES AND GUESTS, AS WELL AS THEIR OWN FORCES, BY

ADEQUATELY PROTECTING ANY EXPOSED LIVE CONDUCTORS,

OR DEVICES THROUGHOUT THE COURSE OF THIS WORK

16. EQUIPMENT CONNECTIONS

PROVIDE FINAL CONNECTIONS FOR ALL EQUIPMENT FURNISHED

UNDER OTHER DIVISIONS AND FOR ALL VA FURNISHED

EQUIPMENT. PROVIDE A FLEXIBLE LIQUID TIGHT CONNECTION

TO ALL VIBRATION PRODUCING EQUIPMENT.

17. TEMPORARY LIGHTING, POWER, FIRE, AND SAFETY

PROVIDE TEMPORARY LIGHTING AND POWER AS REQUIRED IN

AREAS UNDERGOING WORK DURING CONSTRUCTION. FURNISH

AND INSTALL ONE OSHA APPROVED PIGTAIL SOCKET WITH LED

EQUIVALENT 150-WATT LAMP FOR EVERY 500 SQUARE FEET OF

FLOOR SPACE AND A MINIMUM 1 PER ROOM. TEMPORARY

LIGHTING SHALL BE LEFT IN PLACE UNTIL PERMANENT LIGHTING

IS COMPLETELY OPERATIONAL.

FURNISH AND INSTALL POWER OUTLETS TO A TOTAL ONE FOR

EVERY 2,000 SQUARE FEET OR PART THEREOF OF FLOOR AREA

AND THESE SHALL BE 20 AMP, SINGLE PHASE RECEPTACLES

FOR EITHER 110 VOLTS OR AS INDICATED ON THE DRAWINGS.

COORDINATE ADDITIONAL TEMPORARY POWER AND

REQUIREMENTS WITH OTHER TRADES TO PROVIDE AN

ADEQUATE INSTALLATION.

COMPLY WITH NFPA 241 FOR SAFEGUARDING DURING

CONSTRUCTION AND ALTERATION OPERATIONS. IN ADDITION,

ANY OPENINGS IN FIRE RATED SEPARATIONS BETWEEN

OCCUPIED AND UNOCCUPIED (OR OPERATIONAL AND NON-

OPERATIONAL) AREAS SHALL BE SEALED AT THE END OF EACH

WORK DAY WITH AN APPROPRIATE FIRE RATED ENCLOSURE OR

SEALANT. DO NOT COMPROMISE EXISTING SECURITY OR FIRE

ALARM SYSTEMS SERVING THE OCCUPIED OR OPERATIONAL

AREAS.

DURING CONSTRUCTION THE CONTRACTOR SHALL MAINTAIN

ELECTRICAL SERVICE TO THE BUILDING WITHOUT ANY POWER

OUTAGES OR INTERRUPTION AT ALL TIMES. SHOULD IT BE

NECESSARY TO INTERRUPT ANY ELECTRICAL SERVICE OR

UTILITY, THE CONTRACTOR SHALL REQUIRED PERMISSION IN

WRITING FROM THE COR FOR SUCH INTERRUPTION AT LEAST 2

WEEKS IN ADVANCE. ANY INTERRUPTION SHALL BE MADE WITH

A MINIMUM AMOUNT OF DOWNTIME TO THE VA. ANY SHUT-DOWN

TIME SHALL HAVE TO BE ON A PREMIUM TIME BASIS AND SUCH

TIME TO BE INCLUDED IN THE CONTRACTOR'S BID.

CONTRACTOR SHALL ESTABLISH SAFE WORKING PROCEDURES

FOR THE PROTECTION OF THE WORKMEN IN ALL PHASES OF

WORK, COMPLYING WITH THE APPLICABLE PROVISIONS OF ALL

CITY, STATE, AND FEDERAL SAFETY LAWS (OSHA), AND AS

RECOMMENDED IN THE "MANUAL OF ACCIDENT PREVENTION IN

CONSTRUCTION" AS ISSUED BY THE ASSOCIATION OF GENERAL

CONTRACTORS OF AMERICA, INC., 20TH AND E. STREETS, N.W.

WASHINGTON, D.C.

18. POWER COORDINATION

THE CONTRACTOR SHALL PERFORM ALL COORDINATION AND

SCHEDULING OF LOCAL POWER OUTAGES REQUIRED WITH THE

COR. ALL NEEDED POWER OUTAGES TO BE SCHEDULED WITH

THE COR TWO WEEKS IN ADVANCE.

19. CABLING

BRANCH CIRCUITS TO RECEPTACLES, LIGHTING AND MISC.

SMALL LOADS (15 OR 20 AMP CIRCUITS), UNLESS SPECIFICALLY

NOTED OTHERWISE, SHALL BE 2 - #12, 1 - #12 GRD., 3/4" C. A

SEPARATE NEUTRAL SHALL BE RUN FOR EACH CIRCUIT. SEE

WIRE SIZING TABLE ON THIS SHEET.

ALL WIRE SIZE #12 AWG AND LARGER SHALL BE STRANDED AND

SOLID FOR #14 AND SMALLER.

EACH BRANCH CIRCUIT HOMERUN SHALL HAVE NO MORE THAN

THREE CIRCUITS. EACH BRANCH CIRCUIT HOMERUN SHALL

HAVE A SEPARATE GREEN INSULATED EQUIPMENT GROUNDING

CONDUCTOR. ALL CONDUCTORS SHALL BE COPPER TYPE

THWN / XHHW.

20. CABLING SIZES

BRANCH CIRCUIT CABLE SIZING SHALL BE ADJUSTED BASED ON

THE VALUES INDICATED IN THE WIRE SIZING TABLE PER THIS

SHEET.

21. SPECIAL LUG REQUIREMENTS

ANY CABLE WHICH TERMINATES DIRECTLY ON TO A BUS BAR

SHALL BE 2 BOLT LONG BARREL TYPE WITH INSPECTION HOLES

PRODUCED WITH NON FLASHING TYPE DYES AS

MANUFACTURED BY THOMAS AND BETTS, OR EQUAL MINIMUM

10 TONS OF COMPRESSION, HEX CRIMP. THE USE OF HEAT

SHRINK TUBING IS EXPLICITLY FORBIDDEN. THERE SHALL BE NO

"SHINERS" AT THE LUGS.

22. RACEWAYS

ALL WIRE SHALL BE INSTALLED IN THIN WALL (E.M.T.) CONDUIT

UNLESS OTHERWISE NOTED. MINIMUM SIZE SHALL BE 3/4"

EXCEPT FOR DROPS FOR DEVICES, SWITCH LEGS,

TEMPERATURE CONTROL CONDUITS, WHERE INDICATED OR AS

CALLED FOR ON DRAWINGS. ALL THINWALL FITTINGS SHALL BE

OF THE STEEL COMPRESSION GLAND TYPE.

ALL UNDERFLOOR, UNDERGROUND OR EXPOSED-TO-WEATHER

CONDUIT SHALL BE HEAVYWALL GALVANIZED RIGID STEEL.

(G.R.S.), MINIMUM 3/4".

ALL CONDUIT FASTENERS, STRAPS, SUPPORTS ETC. MUST BE

"BOLT-ON" GALVANIZED STEEL ON EXPOSED CONSTRUCTION

AND IN WET AREAS. SNAP-ON BLACK METAL "CADDY" CLIPS IN

METAL PARTITION WALLS AND ABOVE SUSPENDED CEILINGS

WILL BE PERMITTED. ALL FASTENERS, STRAPS, CLIPS, ETC.

SHALL BE UL LISTED FOR THEIR USE.

SUPPORT CONDUIT WITH P1000 UNISTRUT OR APPROVED

EQUAL WITH 3/8" THREADED ROD 8'-0" O.C. MAX.

PROVIDE MYERS HUBS OR EQUAL FOR ALL CONDUIT TO

ENCLOSURE CONNECTIONS.

ALL CONDUIT RACEWAYS SHALL BE CONCEALED IN OR WITHIN:

WALLS, CEILING CAVITY, ROOF CONSTRUCTION (WHERE

APPROVED), SLAB, GRADE, ETC. UNLESS OTHERWISE NOTED.

ANY RACEWAY THAT IS TO BE ROUTED EXPOSED SHALL BE

APPROVED BY THE VA/COR AND SUCCESSFULLY REVIEWED BY

THE ARCHITECT/ENGINEER. PRIOR TO INSTALLATION. ALL

CONDUIT SHALL BE ROUTED PARALLEL OR PERPENDICULAR TO

WALLS AND STRUCTURAL MEMBERS WITH 90° BENDS WHERE

REQUIRED AND SHALL BE RACKED. PULL AND JUNCTION BOXES

SHALL BE HELD TO A MINIMUM. CONTRACTOR SHALL INSTALL

ALL WORK IN NEAT & WORK LIKE MANNER.

GROUND ALL CONDUITS, MOTORS, AND EXPOSED NON-

CURRENT CARRYING METAL PARTS OF ELECTRICAL EQUIPMENT

IN ACCORDANCE WITH ALL PROVISIONS WITH THE LATEST

EDITION OF THE NATIONAL ELECTRICAL CODE. VA

SPECIFICATION SECTION 26 05 26 "GROUNDING AND BONDING

FOR ELECTRICAL SYSTEM".

CONTRACTOR SHALL PROVIDE BOXES, JUNCTION BOXES,

SPLICE BOXES AND FITTINGS WHERE NECESSARY OR

REQUIRED BY THE NEC.

ALL ELECTRICAL CONDUITS TO A MINIMUM OF 3/4". MULTI-GANG

BACKBOXES FOR DIFFERENT VOLTAGES AND TYPES OF

EMERGENCY AND NORMAL BRANCH WIRING DEVICES SHALL

HAVE DIVIDERS BETWEEN DEVICES.

PROVIDE COLOR RED CONDUIT FOR FIRE ALARM. WHERE CORE

DRILLING AND CUTTING OF FLOORS OR WALLS IS REQUIRED, X

RAY THE AREAS PRIOR TO DRILLING. AVOID INTERFERENCE

WITH EXISTING CONCEALED ELECTRICAL, PLUMBING

INSTALLATIONS REINFORCING STEEL. REFINISH DAMAGED AND

CUT SURFACES TO MATCH ADJACENT FINISHES.

CONTRACTOR SHALL FIREPROOF ALL CONDUIT OPENINGS

BETWEEN FLOORS AND ANY INTERSPACE FIRE SEPARATION

BLOCK WALLS WITH AN COR APPROVED U.L. LISTED FIRE

RETARDANT MATERIAL. AS SUCCESSFULLY REVIEWED BY

ARCHITECT/ENGINEER.

23. LIGHTING

ALL FINAL LOCATIONS AND ARRANGEMENTS OF LIGHTING

FIXTURES SHALL BE OBTAINED FROM THE ARCHITECTURAL

REFLECTED CEILING PLAN.

24. RECEPTACLES

CONTRACTOR SHALL VERIFY ALL OUTLET MOUNTING

ARRANGEMENTS, HEIGHTS AND LOCATIONS WITH THE

ARCHITECTURAL DRAWINGS PRIOR TO ROUGH-IN. ANY

MENTION OF A SPECIFIC MOUNTING ARRANGEMENT, HEIGHT OR

LOCATION SHALL NOT RELIEVE THE CONTRACTOR OF THE

RESPONSIBILITY TO VERIFY THE SPECIFIC REQUIREMENT WITH

THE EQUIPMENT FURNISHED OR THE OTHER TRADES WORKING

IN THE SAME AREA. NO ADDITIONS TO THE CONTRACT SUM

WILL BE PERMITTED FOR OUTLETS IN WRONG LOCATIONS, IN

CONFLICT WITH OTHER WORK ETC. THE VA RESERVES THE

RIGHT TO RELOCATE ANY DEVICE 10'-0" PRIOR TO ROUGH-IN

WITHOUT ANY ADDITIONAL CHARGES BY THE CONTRACTOR.

OUTLET BOXES MOUNTED BACK-TO-BACK IN THE SAME WALL

ARE PROHIBITED. A MINIMUM 24" CENTER-TO-CENTER LATERAL

SPACING SHALL BE MAINTAINED BETWEEN BOXES.

ALL DUPLEX RECEPTACLES SHALL BE HOSPITAL GRADE

NEMA 5-20R.

ALL EMERGENCY POWER OUTLETS SHALL BE RED IN COLOR. IN

ROOMS WITHOUT GENERAL ILLUMINATION ON EMERGENCY

POWER, EMERGENCY RECEPTACLES SHALL BE OF THE SELF

ILLUMINATED TYPE.

25. GUARANTEE

ALL EQUIPMENT FURNISHED AND WORK PERFORMED UNDER

THE CONTRACT DOCUMENTS SHALL BE GUARANTEED AGAINST

DEFECTS IN MATERIALS OR WORKMANSHIP FOR A PERIOD AS

PER VA SPECIFICATION, UNLESS OTHERWISE NOTED. ANY

FAILURE OF EQUIPMENT OR WORK DUE TO DEFECTS IN

MATERIALS OR WORKMANSHIP SHALL BE CORRECTED BY THE

CONTRACTOR AT NO COST TO THE VA.

26. FINAL INSPECTION

ALL THE ITEMS AND WORK SHALL BE TESTED FOR SAFE,

PROPER OPERATIONS.

UPON COMPLETION OF THE WORK, THE ELECTRICAL

CONTRACTOR SHALL REVIEW AND CHECK THE ENTIRE PORTION

OF WORK, CLEAN EQUIPMENT AND DEVICES, REMOVE SURPLUS

MATERIALS AND RUBBISH FROM THE VA'S PROPERTY, LEAVING

THE WORK IN NEAT AND CLEAN ORDER AND IN COMPLETE

WORKING CONDITION. THE ELECTRICAL CONTRACTOR SHALL BE

RESPONSIBLE FOR REMOVAL OF ANY CARTON, DEBRIS, ETC.

FOR EQUIPMENT INSTALLED BY THIS CONTRACTOR INCLUDING

EQUIPMENT FURNISHED BY THE VA. THE ABOVE SHALL ALSO

APPLY TO ALL EQUIPMENT FURNISHED BY OTHERS AND

UNPACKED OR REMOVED FROM CARTON, BY THE CONTRACTOR.

1. EXAMINATION

A. THE CONTRACTOR SHALL VISIT THE SITE AND EXAMINE AREAS UNDERWHICH THE WORK IS

TO BE PERFORMED AND NOTIFY THE VA IN WRITING OF ANY CONDITIONS DETRIMENTAL TO

THE PROPER AND TIMELY COMPLETION OF THE WORK. CONTRACTOR SHALL NOT

PROCEED WITH WORK UNTIL SATISFACTORY CONDITIONS HAVE BEEN CORRECTED.

B. VERIFY FIELD MEASUREMENTS AND CIRCUITING ARRANGEMENTS FOR DEVICES SHOWN

ON DRAWINGS.

C. DEMOLITION DRAWINGS ARE BASED ON FIELD OBSERVATION AND EXISTING RECORD

DRAWINGS. REPORT DISCREPANCIES TO COR BEFORE DISTURBING EXISTING

INSTALLATION. CONTRACTOR SHALL COORDINATE WITH COR FOR ANY

HIDDEN/UNFORESEEN WORK FOUND AFTER COMMENCEMENT OF WORK THAT NEEDS TO

BE REWORKED/RELOCATED TO COMPLETE THE NEW WORK.

D. COMMENCEMENT OF DEMOLITION MEANS ACCEPTANCE OF EXISTING CONDITIONS.

E. REVIEW MECHANICAL AND ARCHITECTURAL DEMOLITION DRAWINGS FOR FOR ANY OTHER

ELECTRICAL REQUIREMENTS.

2. PREPARATION

A. DISCONNECT ELECTRICAL ACCESSORIES IN WALLS, FLOORS, AND CEILINGS SCHEDULED

FOR REMOVAL.

3. DEMOLITION AND EXTENSION OF EXISTING ELECTRICAL WORK.

A. REMOVE, RELOCATE, AND EXTEND EXISTING ELECTRICAL WORK AS INDICATED ON THE

DRAWINGS AND AS NOTED HEREIN.

B. ABANDONED WIRING BACK TO SOURCE OF SUPPLY AND REMOVE ABANDONED CONDUIT

BACK TO NEAREST ACCESSIBLE JUNCTION BOX FOR ALL EQUIPMENT SHOWN TO BE

REMOVED.

C. ALL DEMOLISHED EQUIPMENT FROM PANELBOARD SHALL BE, RE-LABELED (TYPE WRITTEN)

AS "SPARE". AFTER DEMOLITION IS COMPLETE, SUBMIT REVISED PANELBOARD

SCHEDULES INDICATING "SPARE" CIRCUIT BREAKER.

D. REMOVE EXPOSED ABANDONED CONDUIT ABOVE ACCESSIBLE CEILING FINISHES. CUT

CONDUIT FLUSH WITH WALLS AND FLOORS, AND PATCH SURFACES. CONDUIT MAY BE

ABANDONED IN WALLS TO REMAIN EXISTING WIRING WITHIN THESE CONDUITS SHALL BE

REMOVED COMPLETELY.

E. DISCONNECT AND REMOVE ABANDONED OUTLETS AND ASSOCIATED DEVICES.

F. DISCONNECT AND REMOVE ABANDONED PANELBOARDS AND DISTRIBUTION EQUIPMENT.

G. DISCONNECT AND REMOVE ELECTRICAL DEVICES AND EQUIPMENT THAT IS NO LONGER IN

USE.

H. DISCONNECT AND REMOVE ABANDONED LUMINARIES, BRACKETS, STEMS, HANGERS, AND

ACCESSORIES, ETC.

I. REMOVE ALL ACCESSIBLE ABANDONED WIRING OF ALL TYPES, OR CAP AND LABEL IN

JUNCTION BOX FOR RE-USE, IN COMPLIANCE WITH THE NATIONAL ELECTRIC CODE.

J. REPAIR ADJACENT CONSTRUCTION AND FINISHES DAMAGED DURING DEMOLITION AND

EXTENSION OF WORK.

K. IF INTERRUPTED MAINTAIN AND RESTORE, ALL WALL AND CEILING FINISHES PASSING

THROUGH UN-RENOVATED AREAS.

4. CLEANING, REPAIR, AND REPLACEMENT

A. GENERAL: CLEAN AND REPAIR EXISTING MATERIALS AND EQUIPMENT THAT WILL REMAIN

OR ARE TO BE REUSED.

B. PANELBOARDS: CLEAN EXPOSED SURFACES AND TIGHTEN ALL ELECTRICAL

CONNECTIONS. REPLACE DAMAGED CIRCUIT BREAKERS AND PROVIDE CLOSURE PLATES

FOR VACANT POSITIONS. PROVIDE TYPED SCHEDULES SHOWING REVISED CIRCUITING

INFORMATION.

C. LUMINARIES: REMOVE EXISTING LUMINARIES AS NOTED.

5. DISPOSAL

A. VA SHALL HAVE RIGHT TO RETAIN ANY EQUIPMENT OR MATERIALS THAT HAVE BEEN

DEMOLISHED PRIOR TO DISPOSAL OR REMOVAL FROM SITE.

B. ANY EQUIPMENT OR MATERIALS NOT WANTED BY THE VA SHALL BECOME THE PROPERTY

OF THE CONTRACTOR AND REMOVED FROM SITE.

C. CONTRACTOR SHALL COMPLY WITH ENVIRONMENTAL LAWS AND REGULATIONS FOR

DISPOSAL OF DEMOLISHED MATERIALS AND EQUIPMENT.

SPECIAL NOTES:

1. EXIT SIGNS SHALL NOT BE INSTALLED IN A MANNER THAT THE SIGN WILL BLOCK FIRE ALARM VISUAL DEVICES.

2. FOR LIGHTING FIXTURES MOUNTING HEIGHTS SEE SCHEDULE AND DRAWINGS.

NOTES:

1. TABLES ARE BASED ON EVENLY DISTRIBUTED LOAD ALLOWING A 3% VOLTAGE DROP AT LAST OUTLET.

2. 480V MOTOR BRANCH CIRCUIT CONDUCTORS SHALL BE #12 AWG IN 3/4" C UNLESS OTHERWISE NOTED.

3. SIZE OF CONDUCTORS ARE BASED UPON EACH MOTOR BEING FED WITH SEPARATE CONDUIT. IF CONDUCTORS FOR TWO MOTORS (MAX.) ARE TO BE

COMBINED IN ONE CONDUIT, INCREASE THE SIZE OF CONDUCTORS AND CONDUITS PER NATIONAL ELECTRICAL CODE (NEC), TO COMPENSATE FOR

CONDUCTOR DE-RATING.

4. PROVIDE DEDICATED NEUTRAL FOR EACH CIRCUIT.

USE COPPER WIRE IN METALLIC CONDUIT,

AWG SIZE AS FOLLOWS ON ENTIRE CIRCUIT

AND SIZE CONDUIT ACCORDINGLY.

*LAST ON

CIRCUIT.

*FIRST ON

CIRCUIT.

IF DISTANCE (A+B) IN FEET IS:

(SEE DIAGRAMAT RIGHT)

TEMPERATURE/HUMIDITY SENSORS 60" TO CENTER LINE OF BOX.

FOR 277V-20A BRANCH CIRCUITS ONLY (UNLESS NOTED OTHERWISE)

WIRE SIZE CONDUIT SIZE

WIRE SIZE CONDUIT SIZE

3/4"

3/4"

3/4"

1"

3/4"

3/4"

3/4"

1"

"B" FT.

* LIGHTING LOAD

1 2 3 4 5 6 7 8 9 10

1 2 3 4 5 6 7 8 9 10

A

B

C

D

E

F

A

B

C

D

E

F

CONSULTANT ARCHITECT/ENGINEER OF RECORD STAMP Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

Drawing Title

Approved: Project Director

Phase Project Title Project Number

Building Number

Drawing NumberLocation

Issue Date Checked Drawn

VA FORM 08-6231

REVIEW ONLY - NOT FOR CONSTRUCTION

Bancroft Project No. VA CONTRACT NO.

12/06/2024

ELECTRICAL - GENERAL NOTES RENOVATIONS TO

BUILDING 217

EDWARD J. HINES JR. VAMC

WG JC

578-20-002

E001

100% CONSTRUCTION

DOCUMENTS

23-00936C25223C0071

DRAWING INDEX - ELECTRICAL

NUMBER TITLE

E001 ELECTRICAL - GENERAL NOTES

E002 ELECTRICAL - SYMBOLS AND ABBREVIATIONS

EPD101 ELECTRICAL - OVERALL DEMO PLAN, FIRST FLOOR

EPD102 ELECTRICAL - OVERALL DEMO PLAN, SECOND FLOOR

EPD401.1 ELECTRICAL - DEMOLITION PLAN, ENTRANCE LOBBY, VESTIBULE, RCC108R & 1A3

EPD401.2 ELECTRICAL - DEMOLITION PLAN, DINING ROOM

EPD401.3 ELECTRICAL - DEMOLITION PLAN, DINING ROOM

EPD401.4 ELECTRICAL - DEMOLITION PLAN, SECOND FLOOR CONFERANCE ROOMS

EPD401.5 ELECTRICAL - DEMOLITION PLAN, BARIATRIC ROOMS

EPD401.6 ELECTRICAL - POWER DEMOLITION PLAN, DEMENTIA UNIT

EPD401.7 ELECTRICAL - LIGHTING DEMOLITION PLAN, DEMENTIA UNIT

EPD401.8 ELECTRICAL - DEMOLITION PLAN, HIGH FALL-RISK PATIEN ROOMS

EPD401.9 ELECTRICAL - DEMOLITION PLAN, EASY STREET

EPD401.10 ELECTRICAL - POWER DEMOLITION PLAN, ELECTRICAL ROOMS

EPD401.11 ELECTRICAL - DEMOLITION PLAN, SMOKE SHELTER

EP101 ELECTRICAL - OVERALL PLAN, FIRST FLOOR

EP102 ELECTRICAL - OVERALL PLAN, SECOND FLOOR

EP401.1 ELECTRICAL - PLANS, PRIMARY & ENTRANCE LOBBY

EP401.2 ELECTRICAL - PLANS, DINING ROOMS 1A118

EP401.3 ELECTRICAL - PLANS, DINING ROOM 2A26

EP401.4 ELECTRICAL - PLANS, LIBRARY

EP401.5 ELECTRICAL - PLANS, BARIATRIC ROOMS

EP401.6 ELECTRICAL - POWER PLAN, DEMENTIA UNIT

ET401.7 ELECTRICAL - TELECOM PLAN, DEMENTIA UNIT

EL401.8 ELECTRICAL - LIGHTING PLAN, DEMENTIA UNIT

EP401.9 ELECTRICAL - PLANS, HIGH FALL-RISK ROOMS

EP401.10 ELECTRICAL - PLANS, EQUIPMENT STORAGE

EP401.11 ELECTRICAL - POWER PLAN, ELECTRICAL ROOMS

EP401.12 ELECTRICAL - PLANS, EASY STREET

EP401.13 ELECTRICAL - POWER PLAN, ROOF

E501 ELECTRICAL - DETAILS

E502 ELECTRICAL - DETAILS

E503 ELECTRICAL - DETAILS

E504 ELECTRICAL - DETAILS

E505 ELECTRICAL - DETAILS

E601 ELECTRICAL - LUMINAIRE AND CONTROLS SCHEDULES

E602 ELECTRICAL - SCHEDULES

E701 ELECTRICAL - DEMOLITION NORMAL POWER SINGLE LINE DIAGRAM

E702 ELECTRICAL - DEMOLITION EMERGENCY POWER SINGLE LINE DIAGRAM

E703 ELECTRICAL - NEW WORK NORMAL POWER SINGLE LINE DIAGRAM

E704 ELECTRICAL - NEW WORK EMERGENCY POWER SINGLE LINE DIAGRAM

E801 ELECTRICAL - PANEL SCHEDULES

E802 ELECTRICAL - PANEL SCHEDULES

E803 ELECTRICAL - PANEL SCHEDULES

E804 ELECTRICAL - PANEL SCHEDULES

E805 ELECTRICAL - PANEL SCHEDULES

E806 ELECTRICAL - PANEL SCHEDULES

Revisions: Date:

30% DESIGN DEVELOPMENT 11/23/2023

60% DESIGN DEVELOPMENT 05/08/2024

90% CONSTRUCTION DOCUMENT 08/23/2024

100% CONSTRUCTION DOCUMENTS 12/06/2024

T

H

B

FR

PP

N P

N D

N BI

N SA

N DS

N ST

N CB

D

N MS

S PA

C

C

P A

DC

CR

ES

ML

CR/K

REX

KP

AIP

DC

RX

ES

ML

CCP

RTLS

QTS

MID

GB

SD

SSD

HD

HD135

SPS

SP

ST

HS

P

F SP

F SPS

STF

HSF

TS

FS

PS

FACP

MM

CM

RTS/I

Z

I

VSS

VTS

LS

XX

XX

GF

TVSS

M

CM

KWH

V

AS

VS

A

ST

T

TV TV

TVTV

TVTV

1/4

1/8

J

1. THIS IS A STANDARD LEGEND SHEET. SOME SYMBOLS OR ABBREVIATIONS MAY APPEAR ON THIS SHEET AND NOT ON THE

PLANS.

ELECTRICAL ABBREVIATIONSELECTRICAL SYMBOLS - DIAGRAM

MOTORS AND CONTROLS

ELECTRICAL SYMBOLS - LIGHTING PLAN

ELECTRONIC SAFETY AND SECURITY SYMBOLS

ELECTRICAL SYMBOLS - COMM. / DATA PLAN

FIRE ALARM SYMBOLSELECTRICAL SYMBOL - POWER PLAN

ELECTRICAL SYMBOL - HVAC POWER PLAN

GENERAL NOTES

NURSE CALL SYMBOLS

PC

OS

S

S

S

S

DH

PB

TC

T

PB

A/V

VFD

GFCI

GFCI

1PH SINGLE-PHASE

1P SINGLE POLE

2/C TWO-CONDUCTOR

3/C THREE-CONDUCTOR

3PH THREE-PHASE

4/C FOUR-CONDUCTOR

4W FOUR-WIRE

A/C UNIT AIR CONDITIONING UNIT

A/E ARCHITECT/ENGINEER

AAP ALARM ANNUNCIATOR PANEL

AC ALTERNATING CURRENT OR ARMORED CABLE

ACC ACCESSIBLE

ADDL ADDITIONAL

ADJ ADJACENT, ADJOINING

ADO AUTOMATIC DOOR OPENER

AF AMPERE FRAME OR AMP FUSE

AFC ABOVE FINISHED COUNTER, AUTOMATIC FREQUENCY

CONTROL, OR AVAILABLE FAULT CURRENT

AFF ABOVE FINISHED FLOOR

AFG ABOVE FINISHED GRADE

AH AMPERE HOUR

AHJ AUTHORITY HAVING JURISDICTION

AIC AMPERE INTERRUPTING CAPACITY

ALT ALTERNATE

AMB OR A AMBIENT

AMP AMPERE

ARCH ARCHITECT

ASC AMPS SHORT CIRCUIT

AT AMPERE TRIP

ATS AUTOMATIC TRANSFER SWITCH

AUTO AUTOMATIC

AV AUDIO VISUAL

BAT BATTERY

BC BARE COPPER

BD BOARD

BFF BELOW FINISH FLOOR

BIL BASIC INSULATION LEVEL

BLDG BUILDING

BPIP BOILER PLANT INSTRUMENTATION PANEL

BRKR BREAKER

BYP BY PASS

C CONDUIT

CAB CABINET

CALC CALCULATE

CAP CAPACITY

CAT CATALOG

CATV COMMUNITY ANTENNA TELEVISION

CCR CONTROL CONTACTOR

CCTV CLOSED CIRCUIT TELEVISION

CB CODE BLUE

cd CANDELA

CD CONSTRUCTION DOCUMENTS

CF CONTRACTOR FURNISHED

CF/CI CONTRACTOR FURNISHED/CONTRACTOR INSTALLED

CF/OI CONTRACTOR FURNISHED/OWNER INSTALLED

CFE CONTRACTOR FURNISHED EQUIPMENT

CHW CHILLED WATER

CHWP CHILLED WATER PUMP

CKT CIRCUIT

CKT BRKR CIRCUIT BREAKER

CLF CURRENT LIMITING FUSE

CLG CEILING

CMU CONCRETE MASONRY UNIT

COAX COAX CABLE

COMM COMMUNICATION

COMPT COMPARTMENT

CONC CONCRETE

CONT CONTINUE

CONTR CONTRACTOR

COORD COORDINATE

CPT CONTROL POWER TRANSFORMER

CRI COLOR RENDERING INDEX

CT CURRENT TRANSFORMER

CTV CABLE TELEVISION

CU COPPER

CU FT CUBIC FEET

CUR CURRENT

DB DECIBEL OR DIRECT BURIAL

DC DIRECT CURRENT

DCP DIMMER CONTROL PANEL

DEG C DEGREES CELSIUS

DEG F DEGREES FAHRENHEIT

DEMO DEMOLITION

DIAG DIAGRAM

DISC DISCONNECT

DISTR DISTRIBUTION

DISTR PNL DISTRIBUTION PANEL

DMR SW DIMMER SWITCH

DN DOWN

DPDT DOUBLE POLE, DOUBLE THROW

DPST DOUBLE POLE, SINGLE THROW

DRSW DOOR SWITCH

DS DISCONNECT SWITCH

DWG DRAWING

EC EMPTY CONDUIT

EG EQUIPMENT GROUND

EL ELEVATION

ELEC ELECTRIC OR ELECTRICAL

ELEV ELEVATOR

EMCP EMERGENCY MONITORING CONTROL PANEL

EMER EMERGENCY

EMI ELECTROMAGNETIC INTERFERENCE

EMT ELECTRICAL METALLIC TUBING

ENCL ENCLOSURE

EPO EMERGENCY POWER OFF

EPRF EXPLOSION PROOF

ESMT EASEMENT

EWC ELECTRIC WATER COOLER

EWH ELECTRIC WATER HEATER

EXIST, EX EXISTING

FA FIRE ALARM

FAAP FIRE ALARM ANNUNCIATOR PANEL

FABL FIRE ALARM BELL

FABX FIRE ALARM BOX

FACP FIRE ALARM CONTROL PANEL

FC FOOTCANDLE

FI FILM ILLUMINATOR

FIXT FIXTURE

FLA FULL LOAD AMPS

FLEX FLEXIBLE METALLIC CONDUIT

FLT FLOODLIGHT

FLUOR FLUORESCENT

FLUOR FIX FLUORESCENT FIXTURE

FOUTT TELEPHONE FLOOR OUTLET

FP FIRE PROTECTION

FT FEET OR FOOT

FU SW FUSED SWITCH

FVNR FULL VOLTAGE NON-REVERSING

FVR FULL VOLTAGE REVERSING

G OR GND GROUND OR GENERATOR

GEN GENERATOR

GFCI GROUND FAULT CIRCUIT INTERRUPTER

GTB GROUND TERMINAL BOX

HID HIGH INTENSITY DISCHARGE

HOA HAND-OFF-AUTOMATIC

HP HORSEPOWER

HT HEIGHT

HZ HERTZ

IESNA ILLUMINATION ENGINEERING SOCIETY OF NORTH AMERICA

IMC INTERMEDIATE METAL CONDUIT

INCAND INCANDESCENT

IR INFRARED

IWH INSTANTANEOUS WATER HEATER

J-BOX, JB JUNCTION BOX

kV KILOVOLT kVA KILOVOLT AMPERE kVAH KILOVOLT AMPERE PER HOUR kVAR KILOVOLT AMPERE REACTIVE kW KILOWATT kWH KILOWATT HOUR kWHM KILOWATT HOUR METER

LED LIGHT EMITTING DIODE

LF LINEAR FEET (FOOT)

LM LUMEN

LP LIGHT POLE

LPS LOW PRESSURE SODIUM

LRA LOCKED ROTOR AMPS

LTCP LOCAL TEMPERATURE CONTROL PANEL

LT LIGHT

LTG LIGHTING

LTG PNL LIGHTING PANEL

LTNG LIGHTNING

LV LOW VOLTAGE

MATV MASTER ANTENNA TELEVISION SYSTEM

MAX MAXIMUM

MC METAL-CLAD

MCA MINIMUM CIRCUIT AMPS

MCB MAIN CIRCUIT BREAKER

MCC MOTOR CONTROL CENTER

MDP MAIN DISTRIBUTION PANEL

MECH MECHANICAL

MG MOTOR GENERATOR

MH MANHOLE

MIN MINIMUM

MOCP MAXIMUM OVERCURRENT PROTECTION

MLO MAIN LUGS ONLY

MT MOUNT

MTD MOUNTED

MTG MOUNTING

MTS MANUAL TRANSFER SWITCH

MV MEDIUM VOLTAGE

MVA MEGAVOLT-AMPERE

MW MEGAWATT MICROWAVE

NA NOT APPLICABLE

NAC NOTIFICATION APPLIANCES CIRCUIT PANEL

NEC NATIONAL ELECTRICAL CODE

NEMA NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION

NEUT OR N NEUTRAL

NFPA NATIONAL FIRE PROTECTION ASSOCIATION

NIC NOT IN CONTRACT

NL NIGHT LIGHT

NO NORMALLY OPEN

NS NO SCALE

NTS NOT TO SCALE

OC ON CENTER

OD OUTSIDE DIAMETER

OL OVERLOAD

P POLE

PA PUBLIC ADDRESS

PB PANELBOARD, PULL BOX, OR PUSHBUTTON

PBPU PREFABRICATED BEDSIDE PATIENT UNIT

PCB POLYCHLORINATED BIPHENYL

PEC PHOTOELECTRIC CELL

PED PEDESTAL

PEND PENDANT

PF POWER FACTOR

PH PHASE

PNL PANEL

POD POWER OPERATED DAMPER

PT POTENTIAL TRANSFORMER

PTRV POWER TYPE ROOF VENTILATION

PVC POLYVINYL CHLORIDE (PLASTIC)

PWR POWER

RCP REFLECTED CEILING PLAN

REC RECESSED

RECPT RECEPTACLE

RGS RIGID GALVANIZED STEEL

RM ROOM

RMS ROOT MEAN SQUARE

REQD REQUIRED

SCC SHORT CIRCUIT CAPACITY

SES SERVICE ENTRANCE SECTION

SD SMOKE DETECTOR

SF SQUARE FOOT (FEET)

SHT SHEET

SI INTERNATIONAL SYSTEM OF UNITS

SPEC SPECIFICATION

SPST SINGLE POLE, SINGLE THROW

SURF SURFACE

SW SWITCH

SWBD SWITCHBOARD

SWGR SWITCHGEAR

TC TIME CLOCK

TEL TELEPHONE

TP TWISTED PAIR

TPS TWISTED PAIR SHIELDED

TTB TELEPHONE TERMINAL BOARD

TV TELEVISION

TYP TYPICAL

UFD UNDERFLOOR DUCT

UGND UNDERGROUND

UL UNDERWRITERS LABORATORY

UON UNLESS OTHERWISE NOTED

UPS UNINTERRUPTIBLE POWER SUPPLY

UTIL UTILITY

V VOLT

VA VOLT AMPERE

VAR VOLT AMPERE REACTIVE

VFD VARIABLE FREQUENCY DRIVE

VOLT VOLTAGE

W WATT

WH WATER HEATER

WP WEATHERPROOF

XFER TRANSFER

XFMR TRANSFORMER

FUSE WITH RATING

NORMALLY CLOSED RELAY CONTACT

NORMALLY OPEN RELAY CONTACT

MOLDED CASE CIRCUIT BREAKER

LOW-VOLTAGE DRAWOUT AIR CIRCUIT BREAKER

SWITCH AND FUSE UNIT

FUSED DRAWOUT POTENTIAL TRANSFORMER

DELTA CONNECTION

TRANSFORMER

WYE CONNECTION

EARTH GROUND

PULL BOX

TIME CLOCK

POWER JUNCTION BOX

TRANSFORMER, PLAN

MOTOR, SINGLE-PHASE

MOTOR, THREE-PHASE

WYE CONNECTION

EARTH GROUND

LADDER CABLE TRAY

PULL BOX

WIREWAY

REGULAR POWER

RECEPTACLE, DUPLEX

RECEPTACLE, DUPLEX ON CRITICAL POWER

RECEPTACLE, DUPLEX WITH GROUND FAULT

CIRCUIT INTERRUPTER

RECEPTACLE, QUADRAPLEX

LIFE SAFETY POWER

CRITICAL POWER

ELECTRICAL STRIP MOLD (OUTLETS ON 2'-0" CENTERS OR AS

DESIGNATED ON DRAWINGS), MTD 3'-6" AFF OR AS INDICATED.

3-GANG COMPARTMENT BOX IN FLOOR FOR TELEPHONE, DATA

& RECEPTACLE.

DOUBLE GANG DEEP AUDIO/VISUAL JUNCTION BOX

SWITCH

BLANK = SINGLE POLE 3 = THREE-WAY

4 = FOUR-WAY K = KEY OPERATED

DM= DIMMER P = WITH PILOT LIGHT

LV= LOW VOLTAGE TM = TIMER OPERATED

WP=WEATHER PROOF X = EXPLOSION PROOF

T= THERMAL OVERLOAD PROTECTION OS= OCCUPANCY SENSOR

SWITCH, LAMP HOLDER POLE

LIGHT FIXTURE RECESSED ROUND CEILING MOUNTED DOWNLIGHT

LIGHT FIXTURE, RECESSED LED, 2'x4'

LIGHT FIXTURE, RECESSED LED 1'x4'

LIGHT FIXTURE, LED, 2'x4' LETTER INDICATES MOUNTING TYPE i.e. LETTER "S" INDICATES SURFACE MOUNTED.

LIGHT FIXTURE, LED LIFE SAFETY

LIGHT FIXTURE, RECESSED LED, 2'x2'

LIGHT TRACK WITH HEADS AS SHOWN

LIGHT FIXTURE, STRIP/INDUSTRIAL LED; LETTER INDICATES TYPE.

LIGHT FIXTURE RECESSED SQUARE CEILING MOUNTED DOWNLIGHT

SWITCH, EXTERIOR PHOTO CELL FOR CONTROL OF EXTERIOR LIGHTING

LIGHTING, UNDERCABINET LIGHT/COVE LIGHT

SWITCH, OCCUPANCY SENSOR REFER TO FIXTURE SCHEDULE FOR TYPE

FIRE ALARM LINE = FA

ELECTROMAGNETIC TYPE DOOR HOLDER OUTLET

EMERGENCY BATTERY BACK-UP EGRESS LIGHT

CEILING MOUNTED RECEPTACLE ON CRITICAL POWER

DOUBLE FACED CEILING OR WALL MOUNTED EXIT SIGN. ARROW INDICATES DIRECTION

SINGLE FACED CEILING OR WALL MOUNTED EXIT

SIGN.

ARROW INDICATES DIRECTION

HOMERUN TO PANELBOARDS. 4#10 + 1#12 GROUND IN 3/4" CONDUIT

THREE PORT TELEPHONE DATA OUTLET - MOUNTED 18"

AFF UNLESS OTHERWISE NOTED.

SECURITY / DURESS-ALARM BUTTON MOUNTED 3" ABOVE COUNTER

TOP

/ COUNTER TOP BACK SPLAH.

JUNCTION BOX WITH DISCONNECT SWITCH AND

FLEXIBLE CONDUIT CONNECTION

AUTOMATIC DOOR OPERATOR PUSH PLATE

CEILING MOUNTED RECEPTACLE

FLOOR RECEPTACLE, DUPLEX

FOUR PORT TELEPHONE/DATA OUTLET -

MOUNTED 18" AFF UNLESS OTHERWISE

NOTED. CABLE AND JACK COLOR AS FOLLOW

VOICE - WHITE, GREEN - VOIP,

BLUE - DATA, RED - DATA

TELEPHONE OUTLET - WALL MOUNTED

CEILING MOUNTED DATA OUTLET

GETWELL NETWORK DATA OUTLET

DUCT SMOKE DETECTOR W/REMOTE TEST STATION

WP INDICATES WEATHERPROOF HOUSING FOR

BOTH

TEMPER SWITCH

FLOW SWITCH

PRESSURE SWITCH

FIRE ALARM CONTROL PANEL

MONITOR MODULE

CONTROL MODULE

REMOTE TEST SWITCH W/INDICATOR

FIRE FIGHTERS TELEPHONE JACK

CEILING MOUNTED SECURITY CAMERA

WALL MOUNTED CARD READER

KEYPAD LOCK

AIPHONE

ACCESS CONTROL PANEL

ROOF POLE MOUNTED SECURITY CAMERA

CAMERA CONTROL PANEL

RECEPTACLE, QUADRAPLEX ON CRITICAL POWER

TV OUTLET - +84" A.F.F. OTHERWISE NOTED

AND EXISTING WORK

POINT OF CONNECTION BETWEEN NEW

LIMIT OF DEMOLITION

RECEPTACLE, DUPLEX WITH GROUND FAULT CIRCUIT

INTERRUPTER MOUNTED AT 44"

WIRELESS ACCESS POINT

INCOMING LINE

GROUND

FUSIBLE SWITCH

CURRENT TRANSFORMER

CONTROL OR POTENTIAL TRANSFORMER

SURGE AND LIGHTNING ARRESTER

CONTACTOR

SHUNT TRIP

AMMETER

AMMETER SELECTOR SWITCH

VOLTMETER

VOLTMETER SELECTOR SWITCH

UTILITY METER

OWNER METER

KILOWATT HOUR METER

TRANSIENT VOLTAGE SURGE SUPPRESSOR

GROUND FAULT

CABLE AND CONDUIT TAG

SEE

SCHEDULE

EQUIPMENT TAG SEE

EQUIPMENT

SCHEDULE

CONDUIT STUBBED DOWN

CONDUIT STUBBED UP

FLEXIBLE CONDUIT

EQUIPMENT CONNECTION

EMERGENCY POWER OFF PUSHBUTTON

BELL

BUZZER

DISCONNECT SWITCH, FUSED (SWITCH/FUSE RATING)

DISCONNECT SWITCH, UNFUSED (SWITCH RATING)

STARTER, COMBINATION WITH DISCONNECT SWITCH

STARTER OR MOTOR CONTROLLER

VARIABLE FREQUENCY DRIVE

30A/20A

30A

SINGLE PHASE MOTOR (HP AS INDICATED)

THREE PHASE (HP AS INDICATED)

VAV BOX

UNIT HEATER (ELECTRIC

COIL)

UNIT HEATER (GAS OR HOT

WATER

TYPE)

FAN POWERED BOX

CP

CPFP

11/8HP

2KW

UH

10KW

1/8HP

EUH

VAV

CP

CP

SPEAKER FOR PUBLIC ANNOUNCEMENT

L6-30R TWIST LOCK RECEPTACLE ON CRITICAL POWER, 250V,

TWO-POLE, 3W GROUNDED

L6-30R TWIST LOCK RECEPTACLE ON NORMAL POWER,

250V, TWO-POLE, 3W GROUNDED

FLOOR RECEPTACLE, DUPLEX ON CRITICAL POWER

F.A. INDIVIDUAL ADDRESSABLE MODULE

F.A. DOOR HOLDER

F.A. DOOR CLOSER

FIRE ALARM SHUT DOWN RELAY

F.A. ZONE ADDRESSABLE MODULE

WALL MOUNTED CARD READER WITH KEYPAD

DOCK DOOR POSITION INDICATOR LIGHT

HDMI OUTLET - CEILING/WALL

COAXIAL OUTLET - CEILING/WALL

TELEVISION ANTENNA SYSTEM OUTLET - CEILING/WALL

FCU

XX

CCT. XX

30A/1P

CONDENSATE PUMP

LIGHT FIXTURE, LED, 1'x4' LETTER INDICATES MOUNTING TYPE i.e. LETTER "S" INDICATES SURFACE MOUNTED.

LIGHT FIXTURE, LED, 2'x2' LETTER INDICATES MOUNTING TYPE i.e. LETTER "S" INDICATES SURFACE MOUNTED.

CHIME

FLOOR MOUNTED

FOUR PORT TELEPHONE/DATA OUTLET

LIGHT FIXTURE, LED CRITICAL POWER

WALL MOUNTED SECURITY CAMERA

CEILING MOUNTED HORN/STROBE (A/V)

CEILING MOUNTED STROBE

CEILING MOUNTED FIRE ALARM SPEAKER

WALL MOUNTED HORN/STROBE

WALL MOUNTED STROBE

WALL MOUNTED FIRE ALARM SPEAKER

CEILING MOUNTED FIRE ALARM SPEAKER/STROBE

WALL MOUNTED FIRE ALARM SPEAKER/STROBE

MANUAL PULL STATION WP-WEATHERPROOF HOUSING

STANDARD, CEILING MOUNTED SMOKE DETECTOR

NURSE CALL, WALL MOUNTED DOME LIGHT

NURSE CALL, WALL MOUNTED BED INTERFACE

NURSE CALL, WALL MOUNTED STAFF ASSIST

NURSE CALL, WALL MOUNTED DUTY STATION

NURSE CALL, CEILING MOUNTED DOME LIGHT

NURSE CALL, WALL MOUNTED PULL CORD

NURSE CALL, WALL MOUNTED STAFF TERMINAL

SOUNDER BASE, CEILING MOUNTED SMOKE DETECTOR

FIXED TEMP (135°), CEILING MOUNTED HEAT DETECTOR

RATE-OF-RISE STD, CEILING MOUNTED HEAT DETECTOR

MEDIUM-VOLTAGE OIL CIRCUIT BREAKER

MEDIUM-VOLTAGE DRAWOUT AIR CIRCUIT BREAKER

POTHEAD

STRESS CONE

LIGHT POLE, ONE MAST ARM, ONE LUMINAIRE

LIGHT POLE, TWO MAST ARMS, TWO LUMINAIRES

LIGHT POLE, POST TOP MOUNT LUMINAIRE

LIGHT POLE, ONE LUMINAIRE

LIGHTING WALL PACK - EXTERIOR BUILDING

LIGHT FIXTURE, BOLLARD, SQAURE

LIGHT FIXTURE, DIRECTIONAL

LIGHT POLE, TWO LUMINAIRES

FLOOR RECEPTACLE, QUADRAPLEX ON CRITICAL POWER

FLOOR RECEPTACLE, QUADRAPLEX

NURSE CALL, COUNTER MOUNTED MASTER STATION

NURSE CALL, WALL MOUNTED CODE BLUE

DOOR CONTACT/DOOR POSITION SWITCH

REQUEST TO EXIT MOTION

DOOR LOCKING MECHANISM/ELECT STRIKE

DOOR LOCKING MECHANISM/MAG LOCK

ACCESS CONTROL PANEL (LNL-AL400ULX)

ACCESS CONTROL POWER SULLPY (AL600ULACMCB)

HUMIDISTAT, WALL MOUNTED

THERMOSTAT, WALL MOUNTED PULL CORD

REQUEST TO EXIT PUSH BUTTON

REAL TIME LOCATING SYSTEM

MOTION INTRUSION DETECTOR

GLASS BREAK SENSOR

DOOR CONTACT (SN-CSD80-W)

ELECTRIC STRIKE (DS160I)

MAG LOCK

CENTRAX EQUIPMENT TRACKING SYSTEM

UNIT HEATER

LIGHT FIXTURE, BOLLARD, ROUND

LIGHTING LANDSCAPE WALL

VALVE TAMPER SWITCH

VALVE SUPERVISORY SWITCH

LEVEL SWITCH

PANELBOARD

J

J

J

WAP

N

F

F

F

F

F

F

F

F

ACP

ACP

ACPS

FA

RECEPTACLE, DUPLEX MOUNTED AT 44"

RECEPTACLE, QUADRAPLEX MOUNTED AT 44"

S

1 2 3 4 5 6 7 8 9 10

1 2 3 4 5 6 7 8 9 10

A

B

C

D

E

F

A

B

C

D

E

F

CONSULTANT ARCHITECT/ENGINEER OF RECORD STAMP Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

Drawing Title

Approved: Project Director

Phase Project Title Project Number

Building Number

Drawing NumberLocation

Issue Date Checked Drawn

VA FORM 08-6231

REVIEW ONLY - NOT FOR CONSTRUCTION

Bancroft Project No. VA CONTRACT NO.

12/06/2024

ELECTRICAL - SYMBOLS AND

ABBREVIATIONS

RENOVATIONS TO

BUILDING 217

EDWARD J. HINES JR. VAMC

WG JC

578-20-002

E002

100% CONSTRUCTION

DOCUMENTS

23-00936C25223C0071

Revisions: Date:

30% DESIGN DEVELOPMENT 11/23/2023

60% DESIGN DEVELOPMENT 05/08/2024

ELEVATOR

1C268

ELEVATOR MACHINE RM.

1A40

ELECTRICAL

1A39

TELE.

1A137A

MECHANICAL

1A32

SOILED LINEN HOLDING

1A130

BUILDING MANAGEMENT

1A128

DIETICIAN

1A125

P.T. OFFICE

1A124

STORAGE

1A23A

HYDRO THERAPY

1A-26

MECHANICAL

1A114

O.T. OFFICE

1A116 O.T. OFFICE

1A-17

TOILET

1A119

MECHANICAL

1A121

STORAGE

1A137

H.A.C.

1A134

NON FOOD STORAGE

1A135

KITCHEN

1A127

DINING ROOM

1A118

LAUNDRY

1A110

NURSING HOME

SUPERVISOR

1A105

LOUNGE

1A104

OFFICE

1A106

OFFICE

1A107

C O

N F

E R

E N

C E

C

L A

S S

A

WOMEN

1A142

MEN

1A141

RECREATION ROOM

1A108

WOMEN

1A113

MEN

1A112

H.A.C.

1A111

NOURISH. KITCHEN

1A115

BATH

1B119

2 BEDROOM

1B120

TOILET

1B121

1 BEDROOM

1B122

2 BEDROOM

1B162

BATH

1B163

PANTRY

1B136

SOILED UTILITY

1B146

HAC

1B147

SHOWER

1B135

CONFERENCE ROOM

1B133

CLEAN UTILITY

1C133

WARD SUPPLY

1C134

H.A.C.

1B-4

SOILED UTILITY

1C146

TEL. CL.

1C43

CONGREGATE BATH

1C135

TOILET

1B-8

LOUNGE / TV ROOM

1C137

OFFICE

1C138

EXAM / TREATMENT

1C139

W/C STORAGE

1C140

NOURISHMENT KITCHEN

1C141

QUIET ROOM

1C142

STORAGE

1C136

ELECTRICAL

1C45

NURSE'S TOILET

1C181

MED.

1C180

BEDROOM

1B123

TOILET

1B124

BEDROOM

1B126

BEDROOM

1B127

TOILET

1B128

BEDROOM

1B130

BEDROOM

1B131

TOILET

1B132 TOILET

1B148

BEDROOM

1B149

TOILET

1B150

SOILED UTILITY

1B151

BEDROOM

1B152

TOILET

1B153

BEDROOM

1B155

BEDROOM

1B156

TOILET

1B157

BEDROOM

1B159

TOILET

1B161

BEDROOM

1B160

BEDROOM

1B164

TOILET

1B165

BATH

1B166

BEDROOM

1B167

BEDROOM

1B168

TOILET

1B169

BEDROOM

1B171

BEDROOM

1B172

BEDROOM

1B175

BEDROOM

1B176

TOILET

1B177

BEDROOM

1B178

TOILET

1B179

TOILET

B103

BEDROOM

B104

TOILET

1B105

BEDROOM

1B106

BEDROOM

1B107

TOILET

1B108

BEDROOM

1B110

BEDROOM

1B111

TOILET

1B112

BEDROOM

1B114

CORRIDOR

1B-84

CLEAN LINEN

1B115BTOILET

1B117

BEDROOM

1B118

TOILET

1C103

PATIENT ROOM

1C104

TOILET

1C105

BEDROOM

1C106

BEDROOM

1C107

TOILET

1C108

BEDROOM

1C110

BEDROOM

1C111

TOILET

1C112

BEDROOM

1C114

BEDROOM

1C115

BATH

1C116

TOILET

1C117

BEDROOM

1C118

BATH

1C119

BEDROOM

1C120

BEDROOM

1C122

TOILET

1C121

BEDROOM

1C123

TOILET

1C125

BEDROOM

1C126

BEDROOM

1C127

TOILET

1C129

BEDROOM

1C130

BEDROOM

1C131

TOILET

1C132

BEDROOM

1C149

TOILET

1C148

TOILET

1C150

BEDROOM

1C151

BEDROOM

1C152 TOILET

1C154

BEDROOM

1C155

BEDROOM

1C156

TOILET

1C158

BEDROOM

1C159

TOILET

1C161

BEDROOM

1C160

BEDROOM

1C162

TOILET

1C163

BEDROOM

1C164

TOILET

1C165

BEDROOM

1C167

BEDROOM

1C168

TOILET

1C170

BEDROOM

1C171

BEDROOM

1C172

TOILET

1C174

BEDROOM

1C175

BEDROOM

1C176

TOILET

1C177

TOILET

1C179

TOILET

1B173

TOILET

1C166

TOILET

1A138 TOILET

1A136

STORAGE

1A108A

REHABILITATION

THERAPY ROOM

1A43

PHYSICAL THERAPY

1A123

TOILET

1C173

PATIENT ROOM

1C178

TOILET

1C169

TOILET

1C157

TOILET

1C153

TOILET

1C128

TOILET

1C124

TOILET

1C113

TOILET

1C109

TOILET

1B174

TOILET

1B170

TOILET

1B158

TOILET

1B154

EQUIP. ROOM

1B151A

TOILET

1B129

TOILET

1B125

STORAGE

1B115A

TOILET

1B113

TOILET

1B109

OFFICE

1B139

OFFICE

1B141

MEDS

1B138

ELECT.

1B143

SUPPLY

1B142

STORAGE

1B145

EMS

1B145A

LOUNGE

1B80

SOILED UTILITY

1A131

ELEVATOR

1C268

J

K

H

M

L

N

O

P

Q

S

R

G

F1

E

D

C

B

A

234567

1010.11111.111.21213141515.11617

1920212223242526

S16

S15

S14

S13

S12

S11

S10

S9

S8

S7

S6

S5

S4

S3

S2

S1

N19

N17

N15.1N14.1

N16N15 S19

S18

S17

S16.1

S15.1

S14.1

N14

N13

N12

N11

N10

N9

N8

N7

N6

N5

N4

N3

N2

N1

EPD401.6

EPD401.8

EPD401.5

EPD401.8

EPD401.2

EPD401.9

EPD401.1

EPD401.11

EPD401.10

EPD401.10

EPD401.10

EPD401.1

EPD401.9

EPD401.2

EPD401.8

EPD401.8

EPD401.7

EPD401.5

1 2 3 4 5 6 7 8 9 10

1 2 3 4 5 6 7 8 9 10

A

B

C

D

E

F

A

B

C

D

E

F

CONSULTANT ARCHITECT/ENGINEER OF RECORD STAMP Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

Drawing Title

Approved: Project Director

Phase Project Title Project Number

Building Number

Drawing NumberLocation

Issue Date Checked Drawn

VA FORM 08-6231

REVIEW ONLY - NOT FOR CONSTRUCTION

Bancroft Project No. VA CONTRACT NO.

BUILDING 217 KEY PLAN

12/06/2024

ELECTRICAL - OVERALL DEMO PLAN, FIRST

FLOOR

RENOVATIONS TO

BUILDING 217

EDWARD J. HINES JR. VAMC

WG BX

578-20-002

EPD101

100% CONSTRUCTION

DOCUMENTS

23-00936C25223C0071

N 1/16" = 1'-0"

ELECTRICAL - DEMOLITION OVERALL PLAN, FIRST FLOOR

A. REFER TO E-001 ELECTRICAL GENERAL CONSTRUCTION NOTES.

B. ANY EXISTING CEILING MOUNTED SPEAKER, STROBE, AND SMOKE

DETECTORS TO BE RE-USED UNLESS OTHERWISE NOTED.

ELECTRICAL DEMOLITION GENERAL NOTES

Revisions: Date:

60% DESIGN DEVELOPMENT 05/08/2024

DN

LAUNDRY

2A32

WOMEN'S TOILET

2A27

MEN'S TOILET

2A28

OFFICE

2A33

OFFICE

2A34

ELECTRICAL

2A3

MECHANICAL

2A5

STORAGE

2A6

OFFICE

2A14

OFFICE

2A15

OFFICE

2A16

KINESIOTHER

2A17

STORAGE

2A18

PATIO

2APATIO

OFFICE

2A1

TOILET

2A9

TOILET

2A10

H.A.C.

2A11

SANCTUARY ROOM

2A12

CONFERENCE ROOM

2A13

OFFICE

2A25

DINING

2A26

NOURISHMENT KITCHEN

2A31

H.A.C.

2A39

MECHANICAL

2A24

PHARMACY

2A23 OFFICE

2A22 TOILET

2C2

MEDS

2C80

PATIENT ROOM

2C4

PATIENT ROOM

2C6

PATIENT ROOM

2C7

PATIENT ROOM

2C10

TOILET

2C9

TOILET

2C13

PATIENT ROOM

2C11

PATIENT ROOM

2C14

PATIENT ROOM

2C15

PATIENT ROOM

2C18

PATIENT ROOM

2C20

TOILET

2C61

TOILET

2B81

MEDS

2B80

TOILET

2B3

OFFICE

B26

OFFICE

2B20

TOILET

2B25

TOILET

2B21

TOILET

2B32

TOILET

2B50

TOILET

2B48

TOILET

2B35A

TOILET

2B54

TOILET

2B58 TOILET

2B61

TOILET

2B63

TOILET

2B65

TOILET

2B66

TOILET

2B69

TOILET

2B73

TOILET

2B77

TOILET

2B79

OFFICE

2B22

OFFICE

2B49

PATIENT RM.

2B59

PATIENT RM.

2B60

PATIENT RM.

2B62

PATIENT RM.

2B64

PATIENT RM.

2B67

PATIENT RM.

2B68

PATIENT RM.

2B71

PATIENT RM.

2B72

PATIENT RM.

2B75

TWO PATIENT RM.

2B76

SPD

2B33

STORAGE

2B34

H.A.C.

2B47

SOILED LINEN

2B46

SHOWER / BATHROOM

2B35

BREAK ROOM

2B42 NOURISH.

2B41

CLEAN SUPPLY

2B40

COPIER/MAIL RM.

2B39

OFFICE

2B38

CONFERENCE ROOM

2B37

SMOKING ROOM

2C37

OFFICE

2C39

STORAGE

2C40

NOURISH.

1C259

LOUNGE

2C42

ELECTRICAL

2C43

SHOWER / BATHROOM

2C35

TEL.

2C45

SOILED LINEN

2C46

WARD SUPPLY

2C34

CLEAN LINEN

2C33

TOILET

2C17

TOILET

2C16

TEL CLOSET

2A4

TOILET

2C79

TOILET

2C77

TOILET

2C74

TOILET

2C70

TOILET

2C66

TOILET

2C65

TOILET

2C63

TOILET

2C58

TOILET

2C53

TOILET

2C50

TOILET

2C48

TOILET

2C32

TOILET

2C29

TOILET

2C25

TOILET

2C19

TOILET

2C5

TOILET

2C3

TOILET

2B74

TOILET

2B70

TOILET

2B57

TOILET

2B53

TOILET

2B29

TOILET

2B24

TOILET

2B19

TOILET

2B17

TOILET

2B16

TOILET

2B13

TOILET

2B9 TOILET

2B5

PATIENT ROOM

2C76

PATIENT ROOM

2C75

PATIENT ROOM

2C78

OFFICE

2A19

PATIENT ROOM

2C72

PATIENT ROOM

2C71

PATIENT ROOM

2C68

PATIENT ROOM

2C67 PATIENT ROOM

2C64

PATIENT ROOM

2C62

PATIENT ROOM

2C60

PATIENT ROOM

2C59

PATIENT ROOM

2C56

PATIENT ROOM

2C55

PATIENT ROOM

2C52

PATIENT ROOM

2C51

HAC

2C47

EQUIP STORAGE

2C49

PATIENT ROOM

2C31

PATIENT ROOM

2C30

PATIENT ROOM

2C27

PATIENT ROOM

2C26

PATIENT ROOM

2C23

PATIENT ROOM

2C22

TOILET

2C21

MECHANICAL

2A20

OFFICE

2C38

TOILET

2C44

2C36

TOILET

2A21

CLEAN LINEN

2A2

OCCUPATION THERAPY

RM.

2A34A

STORAGE

2A35

OFFICE

2A36

OFFICE

2B4

OFFICE

2B7

OFFICE

2B10

OFFICE

2B11

OFFICE

2B14

OFFICE

2B15

OFFICE

2B18

OFFICE

2B23

OFFICE

2B26

OFFICE

2B27

OFFICE

2B30

OFFICE

2B31

PATIENT ROOM

2B51

PATIENT ROOM

2B52

PATIENT ROOM

2B55

PATIENT ROOM

2B56

FAMILY ROOM

2B78

J

K

H

M

L

N

O

P

Q

S

R

G

F1

E

D

C

B

A

234567

1010.11111.111.21213141515.11617

1920212223242526

S16

S15

S14

S13

S12

S11

S10

S9

S8

S7

S6

S5

S4

S3

S2

S1

N19

N17

N15.1N14.1

N16N15 S19

S18

S17

S16.1

S15.1

S14.1

N14

N13

N12

N11

N10

N9

N8

N7

N6

N5

N4

N3

N2

N1

EPD401.3

EPD401.8

EPD401.4

EPD401.8

EPD401.10

EPD401.10

EPD401.10

EPD401.3

EPD401.4

EPD401.8

EPD401.5

EPD401.8

EPD401.5

EPD401.8

1 2 3 4 5 6 7 8 9 10

1 2 3 4 5 6 7 8 9 10

A

B

C

D

E

F

A

B

C

D

E

F

CONSULTANT ARCHITECT/ENGINEER OF RECORD STAMP Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

Drawing Title

Approved: Project Director

Phase Project Title Project Number

Building Number

Drawing NumberLocation

Issue Date Checked Drawn

VA FORM 08-6231

REVIEW ONLY - NOT FOR CONSTRUCTION

Bancroft Project No. VA CONTRACT NO.

BUILDING 217 KEY PLAN

12/06/2024

ELECTRICAL - OVERALL DEMO PLAN,

SECOND FLOOR

RENOVATIONS TO

BUILDING 217

EDWARD J. HINES JR. VAMC

WG BX

578-20-002

EPD102

100% CONSTRUCTION

DOCUMENTS

23-00936C25223C0071

N 1/16" = 1'-0"

ELECTRICAL - DEMOLITION OVERALL PLAN, SECOND FLOOR

A. REFER TO E-001 ELECTRICAL GENERAL CONSTRUCTION NOTES.

B. ANY EXISTING CEILING MOUNTED SPEAKER, STROBE, AND SMOKE

DETECTORS TO BE RE-USED UNLESS OTHERWISE NOTED.

ELECTRICAL DEMOLITION GENERAL NOTES

Revisions: Date:

60% DESIGN DEVELOPMENT 05/08/2024

R e fr ig e ra to r

WAP

N S S

F

S S

N

F

F

P

F

F

WAP

WAP

F

F

F

F

WAP

F

W A

P

TV

F

W A

P

J

FA

A

P

C R

/K

C R

/K

N

F

MIDMID

CR

WAP

J

C R

C R

P P

S

N

J

F

DH

DH

DAS

F

F

N

N

WAP

F

WAP

F

JJ

R e fr ig e ra to r

K

M

L

N

O

P

Q

S

R

1515.11617

SP

SD

SPS

SPS

SP

ST

SD

SP

HS

ST

SP

SD

D

SD

D

SP

D

D

SP

A. REMOVE VAV POWER SUPPLIES NO LONGER IN USE.

B. RECEPTACLES NOTED AS DEMOLISH, REMOVE CONDUITS, PULL BOXES

AND CONDUCTORS BACK TO PANEL SOURCE. UPDATE TYPEWRITTEN

DIRECTORY TO REFLECT CHANGES.

C. LOW VOLTAGE DEVICES NOTED AS DEMOLISH, REMOVE CONDUITS, PULL

BOXES AND CONDUCTORS BACK TO SOURCE.

D. REMOVE ALL ABANDONED WIRING AND CONDUIT BACK TO SOURCE.

E. EXISTING CIRCUITS OUTSIDE OF SCOPE OF WORK SHALL BE EXISTING TO

REMAIN. IF CIRCUITS ARE AFFECTED FROM NEW CONSTRUCTION,

CONTRACTOR SHALL CIRCUIT TRACE AS NECESSARY. CIRCUITS FOR

THESE INTERRUPTED CIRCUITS SHALL BE NEW WIRING. ALL CIRCUITS

THAT ARE SHARED WITH DEVICES OUTSIDE THE AREA OF DEMOLITION

SHALL REMAIN POWERED AND SHALL BE RECONNECTED TO THE EXISTING

ASSOCIATED PANEL FEEDING THESE ITEMS. CONTINUITY SHALL BE

CHECKED FOR ALL LIGHTING, OUTLETS, COMM/DATA OUTLETS, FIRE

ALARM DEVICES IN THE AREAS NOT BEING REMODELED TO ENSURE

PROPER FUNCTIONING.

F. ALL ELECTRICAL DEVICES/EQUIPMENT SHOWN WITH DARK DASH LINES

SHALL BE REMOVED AND DEMOLISHED INCLUDING WIRING, BOXES AND

CONDUIT BACK TO SOURCE, UNLESS OTHERWISE NOTED.

G. ALL ELECTRICAL LUMINAIRES AND LIGHTING CONTROLS SHOWN WITH

DARK DASH LINES SHALL BE REMOVED AND DEMOLISHED, UNLESS

OTHERWISE NOTED.

H. NORMAL POWER AND LIFE SAFETY LIGHTING BRANCH CIRCUITS SHALL BE

RE-USED IN THE RENOVATED AREA.

I. EMERGENCY EXIT SIGN BRANCH CIRCUITS SHALL BE RE-USED IN THE

RENOVATED AREA.

J. WIRELESS ACCESS POINTS SHALL BE CAREFULLY REMOVED AND STORED

IN A VA DESIGNATED SECURED SITE.