05_Fire_Protection.pdf

TS

TS

LOC

1 SUPERVISED INDICATING VALVE (TAMPER SWITCH)

2 MAIN DRAIN SHUT-OFF VALVE

3 ALARM TEST

4 PRESSURE GAUGE

5 FLOW SWITCH

6 CHECK VALVE

7 DOUBLE CHECK DETECTOR ASSEMBLY

8 CONNECTION FLANGE BY FIRE PROTECTION CONSTRACTOR

9 BALL DRIP VALVES-ROUTE TO DRAIN

10 FLOOR OR HUB DRAIN

RISER SCHEMATIC KEYED NOTES:

/3

18"

EXTERIOR

WALL

SPLASH

BLOCK

FS

11 FIRE DEPARTMENT CONNECTION @ 36" AFG

12 2" MAIN DRAIN & TEST OUTLET 18" AFG

13 FORWARD FLOW TEST CONNECTION @ 48" AFG (ABOVE FINISHED

GRADE) (PITCH PIPE TO DRAIN OUTSIDE OF BUILDING)

FINISHED

FLOOR

2"

1"

MINIMUM REQUIRED FEATURES SHOWN. FINAL

PIPING SIZE & DESIGN BY FIRE PROTECTION

CONTRACTOR.

NOTES:

1.

IF ANY SPRINKLER PIPING DOWNSTREAM OF

FLANGED ENTRY TEE IS 6" OR LARGER, USE

WELDED, FLANGED OR THREADED

CONNECTIONS ON ALL PIPING BETWEEN

FLANGED ENTRY TEE AND ALARM VALVES.

2.

FIRE PROTECTION SYMBOLS:

FIRE DEPARTMENT CONNECTION

ORIFICE

FLOW SWITCH

ALARM BELL

ISOLATION VALVE

GATE VALVE

PRESSURE GAUGE

CHECK VALVE

VALVE SUPERVISION/TAMPER

SWITCH

STRAINER

T

PIPE DROP

PIPE RISE

STRAINER

FORWARD FLOW TEST CONNECTION

FIRE PROTECTION HATCH

PATTERN LEGEND:

LIGHT HAZARD (H-1)

EXTRA HAZARD (H-3)

ORDINARY HAZARD (H-2)

1 1/16"

/3

/3

4"MIN.

4"MIN.

4"MIN.

24"MIN.

PLAN VIEW

BPD

BPD

/3

"18"MIN.

/1

"12"-84"

ELEVATION VIEW

FINISHED FLOOR

FLOOR/HUB DRAIN

PITCHED DRAIN

AIR GAP FITTING

LOW POINT

ISOLATION VALVE

HIGH POINT

OBSTRUCTIONS

VALVE HANDLE SIDE

BPD DRAIN

< 2" 2"

2" - 3" 3"

4" 4"

O N

A S

S E

-1

O N

L Y

FLANGE

MAINTAIN 1' ANNULAR GAP

BETWEEN PIPE AND SLAB.

SEAL GAP

EXTERIOR WALL

FINISHED FLOOR LEVEL

GRADE

/3

78" MINIMUM

LOCATE JOINT 24" OUTSIDE OF

FOOTING PRESSURE LINE

45.00°

FOOTING PRESSURE LINE

EXTEND CASING 2" PAST

FOOTING PRESSURE LINE

(TYP)

END SEAL (TYP)

CASING

THRUST

BLOCK

SERVICE

ENTRANCE

PIPE

/3

X

/1

12"

IF DIMENSION "X" IS LESS THAN 12", INSTALL DI OR RCP CASING.

MAINTAIN AT LEAST 2" ANNULAR GAP BETWEEN PIPE AND CASING.

APPLY CASING END SEALS.

FIRE ALARM & MASS NOTIFICATION SYMBOLS

FIRE ALARM PULL STATION

FIRE ALARM ANNUNCIATOR PANEL

SUPERVISED FIRE ALARM HORN LOUDSPEAKER

NEW CONTROL MODULE

FIRE ALARM SPEAKER

FIRE ALARM DUAL WHITE/AMBER MASS NOTIFICATION STROBE, (##) IS

CANDELA RATING

INTELLIGENT PHOTOELECTRIC SMOKE DETECTOR

INTELLIGENT PHOTOELECTRIC DUCT SMOKE DETECTOR

CEILING MOUNTED FIRE ALARM/MASS NOFICATION SPEAKER

NEW SPRINKLER FLOW SWITCH (PROVIDE

ADDRESSIBLE CONTROL MODULE)

NEW MONITOR MODULE

NEW REMOTE TEST SWITCH WITH INDICATOR

NEW SPRINKLER TAMPER SWITCH (PROVIDE

ADDRESSIBLE CONTROL MODULE)

FIRE SUPPRESSION SYSTEM PANEL

S

S

DS

S

MM

CM

FS

TS

RTS/I

FMCP

FAAP

FSS

FIRE & MASS NOTIFICATION CONTROL PANEL

MASS NOTIFICATION SPEAKER VOLUME CONTROLLER.

CONTROLS SPEAKERS WITHIN ROOM INSTALLED.

V

LOCAL OPERATING CONSOLE

FIRE ALARM SPEAKER/DUAL WHITE/AMBER STROBE, (##) IS

CANDELA RATINGS

LINE TYPE KEY

EXISTING TO BE REMOVED BY THIS

CONTRACTOR (DARK DASHED LINE)

EXISTING TO REMAIN WORK

(THIN SOLID LINE)

NEW WORK BY THIS CONTRACTOR

(DARK SOLID LINE)

GENERAL SYMBOLS

KEYED NOTE, USED TO DESCRIBE ADDITIONAL

INFORMATION OF WORK REQUIRED, SPECIFIC TO

THE SHEET AND/OR DETAIL IT IS SHOWN WITH.

DETAIL NUMBER / SHEET NUMBER#/E-###

9.###

FIRE ALARM & MASS NOTIFICATION SYSTEM NOTES:

FIRE ALARM CONTROL UNIT AND MASS NOTIFICATION AUTONOMOUS CONTROL UNIT (FMCP) IS A COMBINED UNIT OF THE FIRE ALARM CONTROL PANEL (FACP) AND THE MNS AUTONOMOUS CONTROL UNIT (ACU). THE UNIT COULD USE

ONE OR MORE ENCLOSURES.

MASS NOTIFICATION ACU SHALL BE INTERFACED WITH THE TELEPHONE SYSTEM, SO THAT ANNOUNCEMENTS MAY BE

MADE OVER THE FA / MNS SPEAKERS VIA THE TELEPHONE SYSTEM.

ALL DETECTION AND ALARM CIRCUITS SHALL BE OF THE SUPERVISED CLASS A, STYLE D FOR INITIATING CIRCUITS AND A SUPERVISED CLASS A, STYLE Z FOR NOTIFICATION APPLIANCE CIRCUITS. SIGNALING LINE CIRCUITS (SLC) SHALL BE CLASS A, STYLE 2α.

MONITORED DEVICES INCLUDE FLOW AND TAMPER SWITCHES.

IF NOTIFICATION APPLIANCE CIRCUIT (NAC) POWER SUPPLIES OR AMPLIFIERS ARE REQUIRED, LOCATIONS SHALL BE APPROVED BY THE OWNER AND SHALL BE ACCESSIBLE TO THE FIRE DEPARTMENT. PROVIDE SMOKE DETECTOR (NOT SHOWN ON FLOOR PLANS) AT EACH NAC POWER SUPPLY/AMPLIFIER LOCATION UNLESS THE ROOM IS COVERED BY AREA SMOKE DETECTION. PROVIDE 120V POWER TO EACH LOCATION. NOTE THE SPEAKERS IN THE

SECURE AREA SHALL HAVE THEIR OWN HIGH GAIN POWER AMPLIFIER.

SEE PLANS FOR SPECIFIC CANDELA (CD) RATINGS ON NOTIFICATION APPLIANCES

ALL JUNCTION, TERMINAL, AND PULLING BOXES AND COVERS SHALL BE PAINTED RED AND SHALL BE IDENTIFIED WITH ENGRAVED LABELS BY CIRCUIT THAT IT CONTAINS. ALL CONDULETS AND SIMILAR UNITS SHALL BE PAINTED RED. ALL DETECTION AND TERMINAL DEVICES SHALL HAVE ENGRAVED PLASTIC OR METALLIC ALPHANUMERIC IDENTIFICATION, WHICH SHALL BE KEYED TO THE POSTED AND OPERATIONS AND MAINTENANCE INSTRUCTIONS.

ALL WIRING SHALL BE PER MANUFACTURER'S RECOMMENDATIONS.

WHEN THE MNS IS ANNOUNCING, AUDIBLE AND VISUAL FIRE ALARMS SHALL BE DE-ENERGIZED. CONTRACTOR SHALL

SUPPLY ALL NECESSARY EQUIPMENT TO ACCOMPLISH THIS PROCEDURE.

ALL SPEAKER AND STROBE CIRCUITS SHALL BE SUPERVISED.

STROBES SHALL BE DUAL AMBER/CLEAR TYPE WITH SEPARATE CABLING TO EACH STROBE.

SEE DRAWING FOR EXACT LOCATION OF REMOTE LOCAL OPERATION CONSOLE (LOC).

ALL SPEAKERS IN THE SECURE AREA SHALL BE TIED INTO THEIR OWN HIGH GAIN AMPLIFIER THAT IS LOCATED IN THE

SECURE AREA ROOM 126.

COORDINATE REQUIRED ALARMS MONITORED AT BASE HEAD END SYSTEM WITH OWNER PRIOR TO PROGRAMMING.

RTS/I

DS MM CM

S S S S

CDCD CDCD

24V POWER

SLC CIRCUIT

ANTENNA CABLING IN CONDUIT

FMCP

COMBINED

FIRE ALARM

CONTROL PANEL

(FACP)

MNS

AUTONOMOUS

CONTROL UNIT

(ACU)

ROOM 174

120 VAC

TO OTHER DUAL AMBER/CLEAR STROBES

AND THEN BACK TO FACP/ACU

TO OTHER SPEAKERS

AND THEN BACK TO AMPLIFIER

MONITORED

DEVICE

CONTROLLED

DEVICE

RTS/I

DS MM CM

S S S S

CDCD CDCD

24V POWER

SLC CIRCUIT

TO OTHER DUAL AMBER/CLEAR STROBES

AND THEN BACK TO FACP/ACU

TO OTHER SPEAKERS

AND THEN BACK TO AMPLIFIER

TO OTHER EQUIPMENT

AND THEN BACK TO FACP/ACU

MONITORED

DEVICE

CONTROLLED

DEVICE

S E

C U

R E

A R

E A

S E

C U

R E

A R

E A

FMCP

COMBINED

FIRE ALARM

CONTROL PANEL

(FACP)

MNS

AUTONOMOUS

CONTROL UNIT

(ACU)

ROOM 126

120 VAC

EWS

TO OTHER EQUIPMENT

AND THEN BACK TO FACP/ACU

EWS

LOC

LOC

LOC

MONACO BT-XM

MASS NOTIFICATION

COMMUNICATOR

ROOM 174

120 VAC

(26) #14 IN 1-1/2" C.

OPTICAL FIBER WITH NO METALLIC SHIELDING, CLADDING OR

STRENGTH MEMBERS PER UFC REQUIREMENTS.

AMPLIFIER

ROOM 126

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

LOC

LOC

LOC

LOC

SCIF GENERAL NOTES:

1. THE VAULT AREA IS CONSIDERED A SENSITIVE COMPARTMENTED

INFORMATION FACILITY. ALL NEW CONSTRUCTION AND RENOVATION TO THE

AREA INCLUDING WALL CONSTRUCTION, FIRE PROTECTION/DETECTION,

MECHANICAL/HVAC, ELECTRICAL, AND TECHNOLOGY SYSTEMS MUST

COMPLY WITH THE REQUIREMENTS PROVIDED IN UNIFIED FACILITY CRITERIA

4-010-05 SENSITIVE COMPARTMENTED INFORMATION FACILITY PLANNING,

DESIGN, AND CONSTRUCTION WITH CHANGE 1, 1 OCTOBER 2013, AND

REFERENCED IC TECH SPEC FOR ICD/ICS 705 TECHNICAL SPECIFICATIONS

FOR CONSTRUCTION AND MANAGEMENT OF SENSITIVE COMPARTMENTED

INFORMATION FACILITIES, VERSION 1.2, DATED 23 APRIL 2012.

2. CONSTRUCTION, GENERAL: UFC 4-010-05 REQUIREMENTS HAVE BEEN

INCORPORATED INTO THE DESIGN DRAWINGS AND SPECIFICATIONS.

CHANGES TO THE SCOPE OF WORK PROVIDED IN THE CONTRACT

DOCUMENTS MAY INVALIDATE THE APPROVALS RECEIVED FOR THIS

CONSTRUCTION, AND COULD RESULT IN THE REMOVAL AND

RECONSTRUCTION OF FINISHED WORK. ANY PROPOSED DEVIATIONS FROM

THE CONTRACT DOCUMENTS MUST BE FULLY REVIEWED AND APPROVED BY

THE COR PRIOR TO IMPLEMENTATION.

3. ALL CONSTRUCTION MUST BE DONE IN SUCH A MANNER AS TO PROVIDE

VISUAL EVIDENCE OF UNAUTHORIZED PENETRATION. CONSTRUCTION MUST

BE COMPLETED IN A MANNER TO PROVIDE THE REQUIRED STC RATINGS FOR

SOUND CONTROL AT THE WALLS IDENTIFIED. THROUGH-WALL

PENETRATIONS OF PIPE, CONDUIT, AND DUCTWORK REQUIRE SPECIAL

CONSTRUCTION AND INSPECTION PROVISIONS WHICH HAVE BEEN

INCORPORATED INTO THE CONTRACT DOCUMENTS.

4. THE CONTRACTOR SHALL SUBMIT A LIST OF ALL MATERIALS USED IN THE

CONSTRUCTION OF THE VAULT AREA, INCLUDING DIMENSIONAL EXTENTS OF

THE USE AND LOCATION(S) WHERE USED IN THE VAULT. THIS LIST SHALL BE

KEPT UP TO DATE DURING THE COURSE OF CONSTRUCTION AND SUBMITTED

TO THE COR AS PART OF THE CLOSE-OUT REQUIREMENTS AT THE END OF

CONSTRUCTION.

5. PHOTOGRAPHY REQUIREMENTS: THE CONTRACTOR IS NOT ALLOWED TO

HAVE PHOTOGRAPHIC OR RECORDING DEVICES IN THE VAULT AREA. 115 FW

CCZ PERSONNEL WILL BE TAKING PICTURES OF ON-GOING CONSTRUCTION

IN ORDER TO DOCUMENT THAT ALL SECURITY MEASURES ARE BEING MET.

THE COR SHALL BE NOTIFIED AT LEAST ONE WORKING DAY PRIOR TO KEY

CONSTRUCTION MILESTONES. KEY CONSTRUCTION MILESTONES INCLUDE

BUT ARE NOT LIMITED TO: WALL CONSTRUCTION, INCLUDING EACH OF

MULTIPLE LAYERS OF GYPSUM BOARD, FINISHING OF PENETRATIONS,

NON-CONDUCTIVE BREAKS OF PENETRATIONS, AND SOUND BATT

INSULATION INSTALLATIONS.

Mead & Hunt, Inc.

2440 Deming Way

Middleton, WI 53562 phone: 608-273-6380 meadhunt.com

SHEET NO.:

SHEET CONTENTS

DO NOT SCALE DRAWINGS

M&H NO.:

DATE:

DESIGNED BY:

DRAWN BY:

CHECKED BY:

ISSUED

© Copyright This document, or any portion thereof, shall not be duplicated, disclosed, or used on any other project or extension of this project except by written agreement with Mead & Hunt, Inc. Mead & Hunt shall not be responsible for any unauthorized use of, or alteration to these documents.

/3

/2

:0

:4

A

M C

R e v it L o c a l\

-1

.0

-P

-C e n tr a l-jo n .t ie d e m e a d h u n t.

c o m

.r v t

W

IS

C O

N S

IN

A

IR

N

A T

IO

N

A L G

U A

R D

T R

U A

X F

IE

L D

A N

G B

M A

D

IS

O N

W

I

A D

A L B

F-001

FIRE PROTECTION &

FIRE ALARM NOTES,

SYMBOLS, ABBREV.,

SCHEDULES &

DETAILS

XGFG132020ANG NO.:

3141300-141489.01

JET/MRF

RMM/ARG

May 4, 2017

MFP/MRF

NO SCALE1

WET PIPE SPRINKLER RISER SCHEMATIC

NO SCALE3

ASSE-1013 & ASSE-1015

NO SCALE2

WATER SERVICE ENTRANCE

12. GENERAL NOTES APPLY UNLESS NOTED OTHERWISE

11. DO NOT SCALE DRAWINGS. USE GIVEN DIMENSIONS. CONTRCTOR SHALL VERIFY ALL CONDITIONS

AND DIMENSIONS AT THE PROJECT SITE PRIOR TO THE START OF CONSTRUCTION. WHERE

SPECIFIC DEMENSIONS, DETAILS OR DESIGN INTENT CANNOT BE DETERMIND, CONSULT COR

BEFORE PROCEEDING WITH THE WORK.

10. NOMINAL FINISHED FLOOR ELEVATION = 100.0 FT. UNLESS OTHERWISE NOTED

9. SEQUENCE OF WORK AND/OR PLACE OF COMMENCEMENT OF WORK SHALL BE

APPROVED PRIOR TO WORK BEING STARTED.

8. VERIFY ALL EQUIPMENT LOCATIONS AND PIPE ROUTING WITH COR PRIOR TO INSTALLATION.

7. TEMPORARILY PATCH ALL ROOF OPENINGS WATERTIGHT UNTIL FINAL CLOSURE CAN BE MADE.

6. ALL EXISTING ROOFING SYSTEMS SHALL BE PROTECTED FROM DAMAGE DURING CONSTRUCTION

ACTIVITIES.

5. ACCURATE AND LEGIBLE RECORD (AS-BUILT) DRAWINGS SHALL BE MAINTAINED AT THE JOB SITE, AND BE SUBMITTED PRIOR TO FINAL PAYMENT.

4. ANY AND ALL INFORMATION SHOWN ON THESE DRAWINGS WITH RESPECT TO

EXISTING STRUCTURES, UTILITIES, AND MECHANICAL SYSTEMS, IS AS EXACT AS

COULD BE SECURED. THE INFORMATION IS NOT WARRANTED NOR GUARANTEED

ACCURATE, FIELD VERIFY ALL EXISTING CONDITIONS PRIOR TO PROCEEDING WITH WORK.

3. ELEVATION OF PIPING INDICATED ON THESE DRAWINGS ARE TO BE USED AS GUIDELINES TO

ASSIST WITH INSTALLATIONS. MINOR CHANGES TO THESE ELEVATIONS MAY BE NECESSARY TO

ELIMINATE UNFORESEEN INTERFERENCES. ANY CHANGE IN ELEVATION SHALL BE APPROVED...

2. THESE DRAWINGS ARE DESIGN DRAWINGS AND ARE DIAGRAMMATIC, THEY MAY NOT

SHOW ALL PHYSICAL ARRANGEMENTS, OFFSETS, BENDS, OR ELBOWS WHICH MAY

BE REQUIRED FOR PROPER INSTALLATION OF VARIOUS MATERIALS, EQUIPMENT, AND PIPING

SYSTEMS IN ALLOTTED SPACES. EXAMINE THESE AND OTHER AVAILABLE DRAWINGS TO DETERMINE

SPACE LIMITATIONS AND INTERFERENCES. MAKE ANY MINOR CHANGES IN LOCATIONS OF

EQUIPMENT, AND PIPING FROM THAT SHOWN ON DRAWINGS AND FOR ALL PHYSICAL DETAILS

REQUIRED FOR INSTALLATION. COST FOR ADAPTING WORK TO JOB SITE CONDITIONS SHALL NOT BE

CONSIDERED AS BASIS OF AN EXTRA COST TO CONTRACT.

1. ABBREVIATIONS INDICATED HERE AND NOT USED IN THE CONTRACT DOCUMENTS DO NOT APPLY

TO THIS PROJECT. ADDITIONAL ABBREVIATIONS MAY BE INDICATED IN THE CONTRACT

DOCUMENTS.

GENERAL FIRE PROTECTION NOTES:

INSTALL EXTENDED SLEEVES AT ALL WALL PENETRATIONS.

PROVIDE SPLASH BLOCKS FOR DRAINS.

PAINT EXPOSED PIPE. SHOW FLOW DIREDTION AND PIPE IDENTIFICATION.

PROVIDE IDENTIFICATION TAGS ON SPECIFIC COMPONENTS. SEE SPECIFICATIONS.

VERIFY ALL EQUIPMENT LOCATIONS AND PIPE ROUTING WITH COR PRIOR TO INSTALLATION.

PROVIDE SUPERVISORY SWITCHES ON ALL ISOLATION VALVES INSTALLED IN CIRCUITS TO ANY

SPRINKLERS.

PROVIDE VALVED OUTLETS TO DRAIN ALL PIPING. ESTEND DRAIN PIPING TO EXTERIOR.

USE VALUES SHOWN IN TABLE 9-4 UFC 3-600-01 (DOD) IN-LIEU OF EQUIVELENT TABLE IN NFPA 13.

USE AREA / DENSITY METHOD TO DETERMINE WATER DEMAND REQUIREMENTS

2. ANG AND UFC SPECIFIC DESIGN REQUIREMENTS INCLUDE BUT NOT LIMITED TO THE FOLLOWING

A. ANG ETL 15-01-04.

B. UFC 3-600-01 (8 AUGUST 2016)

C. NFPA 13 (LATEST PREVAILING EDITION)

D. AMERICAN SOCIETY OF CIVIL ENGINEERS (ASCE) STANDARDS

1. PROVIDE A HYDRAULICALLY DESIGNED WET PIPE SPRINKLER SYSTEM FOR HAZARD

CLASSIFICATION SHOWN. SYSTEM SHALL BE IN CONFORMANCE WITH THE FOLLOWING CODES

AND STANDARDS:

FIRE PROTECTION NOTES:

FLOW GPM: 1500 GPM

RESIDUAL PRESSURE: 82 PSI

STATC PRESSURE: 90 PSI

HYD. OUTLET ELEV.: 20" OFF FINISHED GRADE

TEST HYDRANTS PRESSURE @ HYD. # 10, FLOW @ HYD. #2, 8" WATER MAIN.

LOCATION: TRUAX FIELD ANGB MADISON AT BUILDING 404

DATE OF TEST: AUG. 23, 2016 @ 11:15 AM

FIRE PROTECTION DESIGN / INSTALLATION CONTRACTOR SHALL CONDUCT SEPARATE WATER

FLOW TEST AND USE RESULTS IN HYDRAULIC CALCULATIONS.

NOTE: INFORMATION SHOW FOR BID ONLY, NOT FOR DESIGN.

WATER SUPPLY FLOW BASES FOR BID:

EXTRA (H-3) 500 (1900) 500 (1900) 90

ORDINARY (H-2) 250 (950) 500 (1900) 60

LIGHT (H-1) 250 (950) 500 (1900) 60

CEILING HEIGHT 60 FT.

OR LESS (18.3m)

CEILING HEIGHT

GREATER THAN 60 FT.

(18.3m)

HAZARD

CLASIFICATION

HOSE DEMAND, gpm (lpm)

DURATION, MIN

Table 9-4 Hose Stream Demand and Duration

K-factor 11.2 (160)

11.2 (160)

11.2 (160)

11.2 (160)

11.2 (160)

11.2 (160)

25.2 (360)

N/A

EXTRA

(H-3)

DESIGN

.3/2500 (12/230)

.3/3500 (12/330)

.3/3600 (12/340)

.3/4600 (12/430)

.5/3000 (20/280)

.5/4000 (20/370)

12.0 @ 7 psi

N/A

K-factor 8.0

(115) 8.0

(115) 11.2 (160)

11.2 (160)

11.2 (160)

11.2 (160)

25.2 (360)

N/A

ORDINARY

(H-2)

DESIGN

.2/2500 (8/230)

.2/3500 (8/330)

.2/2500 (8/230)

.2/3500 (8/330)

.2/2500 (8/230)

.2/3500 (8/330)

12.0 @ 7 psi

N/A

K-factor 5.6 (80)

5.6 (80)

11.2 (160)

11.2 (160)

11.2 (160)

11.2 (160)

25.2 (360)

N/A

LIGHT

(H-1)

DESIGN

.1/1500 (4/140)

.1/1500 (4/140)

.2/2500 (8/230)

.2/3500 (8/330)

.2/2500 (8/230)

.2/3500 (8/330)

12.0 @ 7 psi

N/A

WET DRY WET DRY WET DRY WET DRY

HAZARD

CLASIFICATION

CEILING HEIGHT

UP TO 30 FT.

(9.1m)

CEILING HEIGHT

UP TO >30-45FT.

(9.1-13.7m)

CEILING HEIGHT

UP TO 45-60 FT.

(13.7-18.3m)

CEILING

HEIGHT UP TO

60-100 FT.

(18.3m-30.5)

(gpm/ft²)/ft² (mm/min)/m² [minimum K factor]

Table 9-3 Sprinkler Design Demand and Minimum K-Factor

05/04/17 TYPE B3

NO SCALE4

FIRE ALARM & MASS NOTIFICATION RISER DIAGRAM

FS

NF

NF

8"

NF

6"

6"

6"

1/2" 8"

NF

Chimney Pier

FIRE HYDRANT

(PRESSURE READING)

FIRE HYDRANT

(FLOW TEST)

456'-0"

4" FP-W

F P

-W

F P

-W

4" FP-W

PM/PSM

SECURE

VAULT

BREAK

ROOM

VEST

MECH

VEST-1

141-1

VEST

CONFERENCE

STAN

EVAL

Space

HALLWAY

Space

JAN

WOMEN'S

TOILET/

LOCKER

ROOM

STORAGE

AIRCREW

FLIGHT

GROUP

STORAGE

COMM

ELEC

KITCHEN/

VENDING

STOR

BRIEFING/DD

CLASSROOM

SCIF

COPY

ROOM

ARMS

NCOIC

FIRE

ALARM

STORAGE

LIBRARY

BRIEFING

ROOM

INTELLIGENCE

OPEN

OFFICE

INTEL

NCO

INTEL

SUPERVISOR

BRIEFING

ROOM

WEAPONS

HALLWAY

BREAK

ROOM

VEST

AFMT

NCOIC

DO

HALLWAY

OG CHIEF

MISSSION

PLANNING

Space

NVG

AFE

SUPERINTENDENT

AFE

INSPECTION

ROOM

AIRCREW

FLIGHT

GROUP

VEST-2

141-2

LARGE

BRIEFING

STORAGE

Space

Space

FS CC

OG CC

CCA

OSS CC

FLIGHT

COMMANDER

WORK

ROOM

SECURED

VEST

ISSO &

SSR

HALLWAY

MAINT

DEBRIEF

AFE

NCOIC

SIMULATOR

SUPPORT

OFFICE

OPEN

OFFICE

TRAIN

OSF

SCHEDULING

SOF AREA

MEN'S

TOILET/

LOCKER

ROOM

HALLWAY

COMM/

COMPUTER

STORAGE

BREIFING

ROOM

BRIEFING

ROOM

ACMI/CLASSIFIED

WORK

ROOM

AFMT

OPEN

OFFICE

LOBBY

FDC

FORWARD FLOW TEST CONNECTION

MAIN DRAIN AND TEST

F P

-W

F

P -W

4" FP-W

4" FP-W

SCIF BOUNDARY

SCIF BOUNDARY 5.1015.101

5.102

SCIF BOUNDARY

4" FP-W

FIRE ENTRANCE

FIRE RISER

(SEE CIVIL FOR CONTINUATION)

Mead & Hunt, Inc.

2440 Deming Way

Middleton, WI 53562 phone: 608-273-6380 meadhunt.com

SHEET NO.:

SHEET CONTENTS

DO NOT SCALE DRAWINGS

M&H NO.:

DATE:

DESIGNED BY:

DRAWN BY:

CHECKED BY:

ISSUED

© Copyright This document, or any portion thereof, shall not be duplicated, disclosed, or used on any other project or extension of this project except by written agreement with Mead & Hunt, Inc. Mead & Hunt shall not be responsible for any unauthorized use of, or alteration to these documents.

/3

/2

:0

:5

A

M C

R e v it L o c a l\

-1

.0

-P

-C e n tr a l-jo n .t ie d e m e a d h u n t.

c o m

.r v t

W

IS

C O

N S

IN

A

IR

N

A T

IO

N

A L G

U A

R D

T R

U A

X F

IE

L D

A N

G B

M A

D

IS

O N

W

I

A D

A L B

F-101

FIRE PROTECTION -

FIRST FLOOR PLAN

XGFG132020ANG NO.:

3141300-141489.01

JET

RMM

May 4, 2017

MFP

05/04/17 TYPE B3

PLAN

NORTH

TRUE

NORTH

1/8" = 1'-0"1

FIRST FLOOR FIRE PROTECTION PLUMBING PLAN

12" = 1'-0"2

SITE PLAN TEST HYDRANT LOCATIONS

KEYED NOTES

5.101 THERE SHALL BE NO PENETRATIONS THRU PERIMETER OF SCIF BOUNDARY

OTHER THAN SHOWN ON DRAWINGS. (ALL PIPING PENETRATIONS THRU

PERIMETER SCIF-AREA WALLS SHALL BE GROUNDED.)

5.102 METALLIC SPRINKLER (FIRE SUPPRESSION) PIPE: PROVIDE A UL LISTED

DIELECTRIC UNION INSIDE THE SCIF PERIMETER ADJACENT TO THE

PENETRATION, OR GROUND THE CONDUIT WITHIN 6" OF THE PERIMETER

PENETRATION USING A NO. 4 WIRE (0.2043-DIAMETER COPPER WIRE) TO

THE BUILDING GROUND.

H

H

H

H

H

H

H

HH

FA

C

P

H

H

H

H H H

H

HH

H

H

H

H

H

H

H

H

H

H

H H

H

H

H

H

H

H

H

H

H

H

H

H

H

H

H

H H

H

H

H

H

H

H

H

H

H

H

H

HH

H

H

H

H

H

H

H

H

JJ

J

J

J J

A

A

B

B

C

C

D

D

E

E

F

F

G

G

H

H

J

J

K

K

L

L

M

M

N

N

P

P

Q

Q

R

R

S

S

T

T

24 24

23 23

22 22

21 21

20 20

19 19

18 18

17 17

16 16

15 15

14 14

13 13

12 12

11 11

10 10

9 9

8 8

6 6

5 5

4 4

3 3

2 2

1 1

FIRE ALARM DEMOLITION

GENERAL NOTES:

1.

2.

3.

4.

5.

6.

7.

8.

THE INFORMATION SHOWN IS BASED ON EXISTING DRAWINGS AND SITE

OBSERVATIONS TO ASSIST CONTRACTOR IN BIDDING. THE FIRE ALARM

DRAWINGS INDICATE EXISTING ELECTRICAL ITEMS TO BE REMOVED. THE

DRAWINGS ARE INTENDED TO INDICATE THE SCOPE OF WORK REQUIRED

AND DO NOT INDICATE EVERY BOX, CONDUIT, OR WIRE THAT MUST BE

REMOVED. THE CONTRACTOR SHALL VISIT THE SITE PRIOR TO SUBMITTING

A BID AND VERIFY EXISTING CONDITIONS. REFER TO SPECIFICATION

SECTION 26 05 02 FOR ADDITIONAL REQUIREMENTS.

DASHED WALLS ON THE FLOOR PLANS INDICATE EXISTING WALLS BEING

DEMOLISHED. DO NOT RELY ON ELECTRICAL DRAWINGS TO DETERMINE

EXTENT OF GENERAL CONSTRUCTION DEMOLITION. REFER TO THE

ARCHITECTURAL DEMOLITION PLANS FOR THE EXACT EXTENT OF WORK

REQUIRED BY THIS PROJECT. REMOVE ALL DEVICES ON DASHED WALLS

NOT SHOWN ON THE CONTRACT DRAWINGS. REFER TO DEMOLITION

DRAWINGS OF OTHER TRADES.

FIRE ALARM ITEMS REMOVED AND NOT RELOCATED REMAIN THE PROPERTY

OF THE OWNER AND SHALL BE TURNED OVER TO THE OWNER, IN A

STORAGE AREA TO BE DESIGNATED BY THE OWNER. EQUIPMENT BEING

REMOVED SHALL BE HANDLED SO AS NOT TO FURTHER REDUCE ITS VALUE

TO THE OWNER. THE CONTRACTOR SHALL DISPOSE OF MATERIAL THE

OWNER DOES NOT WANT TO REUSE OR RETAIN FOR MAINTENANCE

PURPOSES.

ALL CONDUIT SHALL BE REMOVED WHERE WALLS ARE BEING REMOVED.

WHERE CONDUIT IS IN THE CONCRETE SLAB, CUT OFF FLUSH, PULL OUT

WIRE, AND PLUG. WHERE CONDUIT IS RUN EXPOSED, ALL ASSOCIATED

CLAMPS, SUPPORTS, HANGERS, ETC., SHALL ALSO BE REMOVED. CONDUIT

CONCEALED IN WALL CONSTRUCTION MAY BE ABANDONED IN PLACE IF NOT

AFFECTED BY OTHER CONSTRUCTION.

THIS CONTRACTOR SHALL COORDINATE ALL HIS WORK, INCLUDING

PHASING WITH OTHER CONTRACTORS AT THE JOB SITE BEFORE REMOVING

EXISTING ELECTRICAL AND INSTALLING NEW ITEMS.

EXISTING CONDUIT IN GOOD CONDITION, MAY BE REUSED IN PLACE.

RELOCATED EXISTING CONDUIT SHALL NOT BE ALLOWED. BONDING

CONDUCTORS SHALL BE INSTALLED IN ALL REUSED CONDUIT TO ASSURE

PROPER GROUND PATH.

CONTRACTOR SHALL REMOVE AND INSTALL ALL CEILING TILES AS

REQUIRED FOR THE EXECUTION OF ELECTRICAL WORK THAT IS OUTSIDE

THE CONTRACT LIMITS OF CONSTRUCTION. CONTRACTOR SHALL REPLACE

CEILING TILES WITH IDENTICAL MATERIAL WHERE DAMAGED BY THIS

CONTRACTOR.

REMOVE EXPOSED ABANDONED CONDUIT, INCLUDING ABANDONED

CONDUIT ABOVE ACCESSIBLE CEILING FINISHES. CUT RACEWAY FLUSH

WITH WALLS AND FLOORS, PATCH SURFACES TO MATCH EXISTING. REMOVE

ALL ASSOCIATED CLAMPS, HANGERS, SUPPORTS, ETC. ASSOCIATED WITH

RACEWAY REMOVAL.

Mead & Hunt, Inc.

2440 Deming Way

Middleton, WI 53562 phone: 608-273-6380 meadhunt.com

SHEET NO.:

SHEET CONTENTS

DO NOT SCALE DRAWINGS

M&H NO.:

DATE:

DESIGNED BY:

DRAWN BY:

CHECKED BY:

ISSUED

© Copyright This document, or any portion thereof, shall not be duplicated, disclosed, or used on any other project or extension of this project except by written agreement with Mead & Hunt, Inc. Mead & Hunt shall not be responsible for any unauthorized use of, or alteration to these documents.

5/ 2/

1:

:0

AM

C :\R ev it

Lo ca l\3

-1

9.

-E

-C en tra l-2

7_ m rf.

rv t

W

IS

C O

N

SI

N A

IR

N

AT

IO

N

AL

G U

AR

D

TR

U

AX

F

IE

LD

A N

G B

M

AD

IS

O

N , W

I

AD

AL

B

FD201

FIRST FLOOR

DEMOLITION PLAN -

FIRE ALARM

XGFG132020ANG NO.:

3141300-141489.01

MRF

ARG

May 4, 2017

JRH/MRF

KEYED NOTES

PLAN

NORTH

TRUE

NORTH

1/8" = 1'-0"1 FIRST FLOOR DEMOLITION PLAN - FIRE ALARM

05/04/17 TYPE B3

S SS

S S

S S S

S S S

S

S

S

S

S

S

S S

S S

S S

S S

S

S

S S

S

S

S S

S

S S

S

S

S

S

S

S S

S

S

SS

S

S

S

S

S

S

S

S

S S S S

SSS

S

S

S

S

SS

S

S

S

S

S

S

S

S

S

S

S

S

S

S S

S

S S

S

S S S

S

S

SS

S S

VV

V V

V

S S

S S

V

S

S

S

S S

S

S

S

S

S

S

TSTSFS

S

FS

M M

C M

LOC

LO

C

LOC

LOC

LO

C

LOC

LO

C

FMCP

FM

C

P

FIRE ALARM GENERAL NOTES:

1.

2.

REFER TO TO SHEET F-001 FOR FIRE ALARM AND MASS NOTIFICATION

RISER DIAGRAM.

NEW DEVICES BEING INSTALLED ON EXISTING GYPBOARD WALL SHALL BE

CUT INTO EXISTING WALL AND BE FLUSH MOUNTED.

A

A

B

B

C

C

D

D

E

E

F

F

G

G

H

H

J

J

K

K

L

L

M

M

N

N

P

P

Q

Q

R

R

S

S

T

T

24 24

23 23

22 22

21 21

20 20

19 19

18 18

17 17

16 16

15 15

14 14

13 13

12 12

11 11

10 10

9 9

8 8

6 6

5 5

4 4

3 3

2 2

1 1

INTEL VAULT

CLASSROOM111

INTEL

INTEL OIC

INTEL NCOIC

BRIEFING

ROOM 3

BRIEFING

ROOM 1

HALLWAY

BRIEFING

ROOM 2

BRIEFING

ROOM 4

LIBRARY

STORAGE

BREAK ROOM

MISSION

PLANNING

WEAPONS

ACMI

ISSO & SSR

COMM/

COMPUTER

STORAGE

LOBBY

VEST

MX DEBRIEF

SECURED

VEST

FLIGHT

COMMANDERS

OPEN OFFICE

PM/PSM

SECURE

VAULT

CORR

SIMULATOR

ELEC

FIRE ALARM

SIMULATOR

SUPPORT

OFFICE

ARMS NCOIC

VEST

ARMS

COPY ROOM

SOF 141

VEST

AFMT NCOIC

STORAGE

TRAINING

OFFICER

SCHEDULING

HALLWAY

AIRFIELD

MANAGEMENT

DIRECTOR OF

OPERATIONS

FIGHTER

SQUADRON

COMMANDER

OPERATIONS

GROUP

COMMANDER

VEST149

HALLWAY

HALLWAY

CONFERENCE

ROOM

STAN EVAL

OPERATIONS

CHIEF 151

CCA

OSS

COMMANDER

MEN'S

TOILET/

LOCKER

ROOM

AFE NCOIC

AIRCREW

FLIGHT

EQUIPMENT

AFE

SUPERINTENDENT,

FEO

NVG

AFE

INSPECTION

ROOM

STORAGE163

JANITOR

WOMEN'S

TOILET/

LOCKER

ROOM

HALLWAY

VEST

KITCHEN/

VENDING

BREAK ROOM

MAIN

BRIEFING

ROOM

MECH

AFE

STORAGE

ELEC

COMM

F-201

F-201

15 15

15 15

15 15 15

151515

WP

WP

WP

WP

WP

WP

WP

9.401

9.401

9.401

9.401

9.401

9.401

9.401

9.402

9.404

9.403

9.402

9.4039.403

9.4039.403

9.403

DS DS

DS

DS

DS

WP

9.407

DS

DS

DS

DS DS

166C

STORAGE

166B

STORAGE

166A

STORAGE

WOMENS

ENTRY

TO RTS/I LOCATED

IN FIRE ALARM 126

TO RTS/I LOCATED

IN FIRE ALARM 126

R

TS

/I

(3)

TO RTS/I LOCATED

IN JAN 163

TO RTS/I LOCATED

IN FIRE ALARM 126

CONTROL MODULE SHALL BE

INTERFACED INTO BUILDING

PAGING SYSTEM SO THAT

PAGING SYSTEM IS SILENCED

UPON FIRE ALARM INITIATION.

T

T

16 16

ELEC

MONACO

INTERFACE

PANEL

19 19 18 18

FIRE ALARM

RTS/I(7)

1/2" MINIMUM

SEPARATION BETWEEN

STEEL CONDUIT

CLASS 1 TYPE A

DIELECTRIC LINK

THREADED COUPLING

(SCH. 80 PVC)

SECURE AREA INTERIOR WALL

SEAL WITH ACOUSTICAL FIRE PROOF

SEALANT ALL THE WAY AROUND

Mead & Hunt, Inc.

2440 Deming Way

Middleton, WI 53562 phone: 608-273-6380 meadhunt.com

SHEET NO.:

SHEET CONTENTS

DO NOT SCALE DRAWINGS

M&H NO.:

DATE:

DESIGNED BY:

DRAWN BY:

CHECKED BY:

ISSUED

© Copyright This document, or any portion thereof, shall not be duplicated, disclosed, or used on any other project or extension of this project except by written agreement with Mead & Hunt, Inc. Mead & Hunt shall not be responsible for any unauthorized use of, or alteration to these documents.

5/ 3/

:3

7:

P M

C :\R ev it

Lo ca l\3

-1

9.

-E

-C en tra l-2

7_ m rf.

rv t

W

IS

C O

N

SI

N A

IR

N

AT

IO

N

AL

G U

AR

D

TR

U

AX

F

IE

LD

A N

G B

M

AD

IS

O

N , W

I

AD

AL

B

F-201

FIRST FLOOR PLAN -

FIRE ALARM

XGFG132020ANG NO.:

3141300-141489.01

MRF

ARG

May 4, 2017

JRH/MRF

KEYED NOTES

9.401 CONDUIT ASSOCIATED WITH EXTERIOR MOUNTED FIRE ALARM

NOTIFICATION DEVICE SHALL BE ROUTED INTERIOR TO THE BUILDING IN

FURRED CAVITY. CORE DRILL EXTERIOR WALL FOR CONDUIT INSTALLATION.

PROVIDE SURFACE MOUNTED EXTERIOR WEATHERPROOF BACKBOX.

9.402 SECURE AREA PERIMETER. COORDINATE WITH GENERAL CONTRACTOR.

MINIMIZE, CO-LOCATE, AND SEAL ALL SECURE AREA PENETRATIONS. SEE

DETAIL 1/E-501. CAULK AND SEAL ALL CONDUIT PENETRATIONS IN A

MANNER THAT MAINTAINS ROOM'S SOUND TRANSMISSION CALSS (STC)

RATING OF 55. ALL DEVICES/CONDUIT LOCATED ON THIS PERIMETER WALL

SHALL BE SURFACE MOUNTED.

9.403 DOTTED LINE INDICATES BOUNDARY OF SOUND ASSEMBLY GROUP 4 -

MINIMUM STC 55. CAULK AND SEAL ALL CONDUITS IN A MANNER THAT

MAINTAINS ROOM'S SOUND TRANSMISSION CLASS (STC) RATING OF 50.

9.404 FIRE ALARM WIRELESS ANTENNA SHALL BE SURFACE MOUNTED TO

EXTERIOR FACADE ABOVE ROOF.

9.407 SECURE AREA PERIMETER. COORDINATE WITH GENERAL CONTRACTOR.

MINIMIZE, CO-LOCATE, AND SEAL ALL SECURE AREA PENETRATIONS. SEE

DETAIL 4/F-201.

PLAN

NORTH

TRUE

NORTH

1/8" = 1'-0"1 FIRST FLOOR PLAN - FIRE ALARM

PLAN

NORTH

TRUE

NORTH

1/4" = 1'-0"2 ENLARGED FIRE ALARM PLAN - ELEC 170

PLAN

NORTH

TRUE

NORTH

1/4" = 1'-0"3 ENLARGED FIRE ALARM PLAN - FIRE ALARM 126

NO SCALE4 SECURE AREA PENETRATION DETAIL

05/04/17 TYPE B3