S-3_USS_CHOSIN_PPI_QA1_final.xlsm

QA1

USS CHOSIN (CG 65) MODPRD Pre-Proposal Information (PPI) Questions

please contact Justin Lessel, justin.d.lessel@navy.mil, and Martha Bello, martha.bello@navy.mil.

Question #2 - Please identify which valves on attachment B have hydraulic valve operator and reach rods.

(a) Definitions.

(i) A "zero-tier reference" is a specification, standard, or drawing that is cited in the contract (including its attachments).

(ii) A "first-tier reference" is either: (1) a specification, standard, or drawing cited in a zero-tier reference, or (2) a specification cited in a first-tier drawing.

(b) Requirements.

All zero-tier and first-tier references, as defined above, are mandatory for use. All lower tier references shall be used for guidance only.

It is the Contractors understanding that all required references listed in paragraph 2 of a zero-tier specification (work item) are "first tier" references. However, when a zero-tier specification directs to use a first-tier reference as "guidance", bidders should not estimate the reference and only use it to aid in the development of an estimate of references that are to be accomplished.

2) If so, verify that all paint applied outside of the United States met NAVSEA Standard Item FY-19 Change 2, 009-32, table 1 thru 8 requirements? 1) It is unknown when the ship was last painted.

2) Govt cannot confirm when the ship was last painted, but can confirm it was sometime prior to 2016. KTR shall assume SI FY 19 requirements were not used.

Various RFP_N00024-19-R-4447, Page 81 of 163

1.8 GOVERNMENT FURNISHED MATERIAL: Government Furnished Material (GFM) cited in work specification(s) and/or Statement of Work (SOW) will be shipped to the contractor’s facility. The successful offeror is to coordinate delivery of GFM with the Project Manager. Government property permanently removed from a vessel that requires a Property Administrator’s disposition instructions shall be properly prepared for shipment and be delivered as direct by the Property Administrator. GFM will be listed in paragraph 5 of Work Item(s).

1.8.2 The following is applicable to in homeport contractors: Government Furnished Material (GFM) cited in the solicitation will be shipped to the contractor’s facility for NAVSEA items only. The contractor is to coordinate delivery of NAVSEA Government Furnished Material with the Project Manager. The contractor is to coordinate pickup of TYCOM Government Furnished Material from the Naval Base with the Project Manager. This GFM will be available at A-30 from one building on the Naval Base. Contractor shall develop pick up schedule accordingly. Transportations costs shall be included in the contract. Change order will only be issued if there is a Government caused change to the pickup date. Government property permanently removed from a vessel that requires a Property Administrator's disposition instructions shall be properly prepared for shipment and be delivered as directed by the Property Administrator. GFM will be listed in paragraph 5 of the Work Item(s).

Question 1) For the TYCOM GFM will the Government provide a Building Number along with a POC including phone number?

Question 2) For planning purposes can the Government provide a number of crates, boxes and pallets of TYCOM GFM?

Q1) kSARIA Corporation, 2055 Sanyo Ave, Suite 200, San Diego, CA 92154, POC: Chris Hensley, Mobile: (619) 600-2155, chensley@ksaria.com Q2) The government is unable to provide number of crates, boxes and pallets.

456-90-003 Shipalt CG47-77614.03K, ACB12/TI12 OA Computer Plant Upgrade; accomplish Para 3.2 states accomplish ref 2.4 through 2.22 and applicable portions of 2.23 through 2.35.

Ref 2.27 (drawing 8710392) is an arrangement drawing that shows rip out and installation of equipment. The drawing also lists equipment that is being ordered on second tier references 4 and 27 listed in 8710392, which are not called out on the spec.

Ref 2.11 (drawing 8709464) is an arrangement drawing that has rip out and installation of equipment, and equipment is being ordered on second tier references 21, 20, 31,32, 33, 34, 35 and 36 listed in 8709464 which are not called out on the spec.

Ref 2.36 (drawing 8710393) is an arrangement drawing that has rip out and installation of equipment, and equipment is being ordered on second tier references 12, 15 and 24, which are not called out on the spec.

Ref 2.35 (drawing 8710392) is an arrangement drawing that has rip out and installation of equipment, and equipment is being ordered on second tier references 8, 9, 11, 17, 21, 23, 28, 29, 30, 31,35, and 43, which are not called out on the spec.

Ref 2.5 drawing 8710392 is an arrangement drawing that has rip out and installation of equipment, and equipment is being ordered on second tier references 20 drawing 8710392 , which are not called out on the spec.

Ref 2.19 drawing 8710249 is an arrangement drawing that has rip out and installation of equipment, and equipment is being ordered on second tier references 16, 17, 18, 27, 28, and 29 , which are not called out on the spec.

Ref 2.15, 2.38, 2.39 and 2.40 is an arrangement drawing that has rip out and installation of equipment, and equipment is being ordered on drawing 8709623, 8709627, 8709625 which is not called out on the spec.

Ref 2.3 drawing 8709658 is an arrangement drawing that has rip out and installation of equipment, and equipment is being ordered on drawing 8709659 which is not called out on the spec.

There is no statement of what to repair in this work item, Paragraph 4.2 states; "Work accomplished by this work item will clear DFS-CG-65-1006-2012",

*Contractor notes that the Attachment J-1 Specification Package No. TPPC-CG65-SWRMC19-CN01 does not contain the above listed specification.

*Contractor note that the following (2) references was note provided by the Customer.

-Reference 2.2, 3300, USFF AT OPORD, (CONFIDENTIAL) -Reference 2.3, 251702ZJUN15, Safety/Security/CG LSD Modernization Program EXORD, (CONFIDENTIAL)

Ref 2.5 drawing 8710392 is an arrangement drawing that has rip out and installation of equipment, and equipment is being ordered on second tier references 32 and 48, which are not called out on the spec.

Ref 2.3 (drawing 8709732) is an arrangement drawing that has installation of new equipment. The equipment is being ordered on second tier references 4 and 5, which are not called out on the spec.

QUESTION; This type of apron typically comes already installed to the Type XVIII Aircraft Securing Fittings (as one piece). Are the Aprons being provided as part of the Aircraft Securing Fittings or will the contractor be required to weld the apron to the fitting and then install?

QUESTION; Is 50 square feet the total of bulkhead & deck plating or is 30 square feet of each? and how many Linear Feet of tees are to be replaced?

QUESTION; Is 50 square feet the total of bulkhead & deck plating or is 50 square feet of each? and how many Linear Feet of tees are to be replaced?

QUESTION; Is 50 square feet the total of bulkhead & deck plating or is 50 square feet of each? and how many Linear Feet of tees are to be replaced?

QUESTION; Is 30 square feet the total of bulkhead & deck plating or is 30 square feet of each? and how many Linear Feet of tees are to be replaced?

Question #1 - Data sheet does not provide the following information needed to price.

1. length of hoses –

2. End fittings required

3. Style

Question #2 - Please confirm 14,000 psi, subcontractors do not know of any hose goes that high.

Please provide information and confirm or advise of PSI.

Q #1. Request hoses be templated for shipboard conditions (template from existing) and verify possible reuse of fittings.

Q #2 The government reviewed ref 2.6 hose data, and did not see any test pressure over 5000 PSI. 14000 PSI is burst pressure not test pressure.

We expect that as the planning tempo ramps up on the MODPRD's, we will receive Amendments, Errata, and possible Addendums, further stressing the schedule for this proposal. It is a significant challenge to adjudicate changes in this constrained environment with other proposals also incurring changes.

Question:

&P of &N

Attachment A

&P of &N image1.jpeg image2.png