Final Draft WPPD2111 West Point India White Coat July 17 2026 Mens_.pdf

FINAL DRAFT w/ Updated Final measurements

DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.

INCH-POUNDS

WP-PD-21-11

17 July 2026

PURCHASE DESCRIPTION

COAT, INDIA WHITE, MEN’S

This purchase description is approved for use by the United States Military Academy (USMA).

1. SCOPE

1.1 Scope. This purchase description covers the requirements for an India White Coat constructed with a polyester/ cotton twill cloth and is intended to be worn by the Men in the

Corps of Cadets at the United States Military Academy (USMA) at West Point.

1.2 Classification. The Coat will be available in the following sizes:

1.2.1 Sizes.

Chest

Size

MEN’S SIZES

Lengths

Extra Short

(XS)

Short

(S)

Regular

(R)

Long

(L)

Extra Long

(XL)

35 X X X X X

36 X X X X X

37 X X X X X

38 X X X X X

39 X X X X X

40 X X X X X

41 X X X X X

42 X X X X X

43 X X X X X

44 X X X X X

45 X X X X X

46 X X X X X

Comments, suggestions, or questions on this document should be addressed to: Department of the U.S. Army, DEVCOM - Soldier Center, ATTN: FCDD-SCD-PEC, 10 General Greene

Avenue, Natick, MA 01760-5019, and the Cadet Uniform Factory, 687 Hardee Place, West Point, NY, 10996, ATTN: ASCE-LWP-CU.

AMSC N/A FSC 8405

Chest

MEN’S SIZES - Continued

Lengths

Extra Short

(XS)

Short

(S)

Regular

(R)

Long

(L)

Extra Long

(XL)

47 X X X X X

48 X X X X X

49 X X X X X

50 X X X X X

51 X X X X X

52 X X X X X

53 X X X X X

54 X X X X X

2. APPLICABLE DOCUMENTS

2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3 and 4 of this specification, whether or not they are listed.

2.2 Government documents.

2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract.

COMMERCIAL ITEM DESCRIPTIONS

A-A-50198 - Thread, Buttonhole Gimp

A-A-50199 - Thread, Polyester Core, Cotton or Polyester-Covered

DEPARTMENT OF DEFENSE SPECIFICATIONS

MIL-B-1563 - Buttons, Insignia and Findings (U.S.M.A), General Specification For

MIL-DTL-1563/6 - Insignia, U.S.M.A., Button, Ball, 25 Ligne

MIL-DTL-1563/7 - Insignia, U.S.M.A., Button, Ball, 36 Ligne

MIL-DTL-1563/19 - Insignia, U.S.M.A., Toggle

DEPARTMENT OF DEFENSE STANDARDS

MIL-STD-1490 - Provisions For Evaluating Quality of Coats, Men’s Dress

(Copies of these documents are available online at https://quicksearch.dla.mil) https://quicksearch.dla.mil/

2.2.2 Other Government documents, drawings, and publications. The following other

Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation or contract.

PURCHASE DESCRIPTIONS

WP-PD-21-01 Cloth, Twill, Polyester/Cotton, White (Local Stock Number C0053)

(Copies of this document are available through the contracting activity.)

2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract.

AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC)

AATCC EP9 - Evaluation Procedure for Visual Assessment of Color Difference of

Textiles

AATCC TM130 - Soil Release: Oily Stain Release

AATCC TM150 - Test Method for Dimensional Changes of Garments After Home

Launderings

AATCC TM158 - Dimensional Changes on Drycleaning in Perchloroethylene: Machine

Method

(Copies of these documents are available online at https://aatcc.org)

ASTM INTERNATIONAL

ASTM D3990 - Standard Terminology Relating to Fabric Defects

ASTM D6193 - Standard Practice for Stitches and Seams

ASTM D6544 - Standard Practice for Preparation of Textiles Prior to Ultraviolet (UV)

Transmission Testing

(Copies of these documents are available online at https://www.astm.org)

2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Unless a specific exemption has been obtained, nothing in this document, supersedes applicable laws and regulations.

3. REQUIREMENTS

3.1 Inspections.

3.1.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection in accordance with 4.2.

https://aatcc.org/ https://www.astm.org/

3.1.2 Conformance inspection. When specified (see 6.2), a sample shall be subjected to conformance inspection in accordance with 4.3.

3.1.3 Component and end item inspection. When specified (see 6.2) a sample shall be subjected to component and end item inspection in accordance with 4.4.

3.2 Standard sample. Unless otherwise indicated, the finished Coat shall match the standard sample for shade and appearance and shall be equal to or better than the standard sample with respect to all characteristics for which the standard sample is referenced (see 6.3) when tested as specified in 4.5.4.1.

3.3 Recycled, recovered, environmentally preferable, or biobased materials. Recycled, recovered, environmentally preferable, or biobased materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs.

3.4 Design. The coat shall be unlined, single breasted with a top collar, and a six (6) button closure. There shall be two (2) chest pockets with button down pocket flaps and epaulettes on both shoulders.

3.4.1 Figures. Figures 1 through 3 are furnished for informational purposes only. To the extent of any inconsistencies between the written document and the figures, the written document shall govern.

3.5 Materials.

3.5.1 Basic material shell fabric (Local Stock Number C0053). The basic material used for the shell shall be in accordance with WP-PD-21-01 Polyester/ Cotton twill cloth treated with optical brightener and a soil release finish. The color shall be White.

3.5.2 Fusible interfacing (Local Stock Number TR0130). The fusible interfacing shall be 60 inches wide. (See 6.6.5)

3.6 Components.

3.6.1 Threads.

3.6.1.1 Thread (Local Stock Number TH0043) The thread for stitching and seaming shall be spun staple 100 percent polyester, conforming to A-A-50199 Type II, TEX 36-45, 2 ply. As an alternate, cotton thread conforming to Type I of A-A-52094 may be used. The color for stitching the coat shall be white and a good match to the basic material. (See 6.6.1).

3.6.1.2 Buttonhole gimp (Local Stock Number TH0015). The gimp for reinforcing the buttonholes shall be cotton, soft finish or glazed finish, TEX 210 conforming to Types I or II of

A-A-50198. The color for stitching the coat shall be white and a good match to the basic material

(See 6.6.1).

3.6.2 Buttons and toggles.

3.6.2.1 Button, Brass, USMA (Local Stock Number B0031). The button shall be brass with no toggle conforming to MIL-B-1563 and MIL-DTL-1563/6, ligne 25. (See 6.6.2).

3.6.2.2 Button Brass, USMA (Local Stock Number B0050). The button shall be brass with concave back conforming to MIL-B-1563 and MIL-DTL-1563/7, 36 ligne with concave back and 7/32-inch stem. (See 6.6.2).

3.6.2.3 Toggle (Local Stock Number A0050). The toggle shall be 3/4-inch long and conform to MIL-B-1563 and MIL-DTL-1563/19. (See 6.6.2).

3.6.3 Hook and eye tape.

3.6.3.1 Eye-tape (Local Stock Number F0074). The eye tape shall be white and conform to part #8848. (See 6.6.3).

3.6.3.2 Hook-tape (Local Stock Number F0075). The hook tape shall be white and conform to part #7986. (See 6.6.3).

3.6.4 Labels (Local Stock Number TR0095). The labels shall conform to the labels produced at the CUF in accordance with CUF requirements. (See 6.6.4).

3.6.4.1 Identification label. The identification label shall be sewn down on all four (4) sides and shall be positioned on the coat, on the lower left front facing towards the body approximately 6-inches above the hem of the coat The stitching shall not cover the printing and shall not be visible on the shell of the coat.(See figure 1).

3.6.4.2 Size and barcode label. Each coat shall have a barcode on the size label. The bar coding element shall be the 13-digit NSN. The barcode for NSN shall be a medium to high density and shall be located at the bottom of the identification label shall be stitched on one (1) side at the top of size/ bar code label. The size label shall include the chest size and length for the Men (See figure 1). Any additional labels or hang tags that may be added shall be according to CUF Procedures and shall cause no damage to the coat.

NOTE: Lot number shall be stamped or printed with indelible black ink prior to shipment.

FIGURE 1. Identification label, size and barcode label.

3.7 Construction.

3.7.1 Patterns. Standard patterns, to be used for cutting the contractor’s working patterns, shall be furnished by the CUF. Minor pattern modifications are permitted to accommodate automation and manufacturing procedures; however, the design and finished measurements must be maintained. The patterns provide for a seam allowance of 3/8-inch (±1/16-inch).

3.7.1.1 List of pattern parts. The pattern list in Table I is provided to ensure that the pattern set is complete.

TABLE I. Pattern list of parts - Men’s.

Cloth Nomenclature Pattern Name Cut Direction Cut Pieces

Shell

(C0053)

Front MWhiteCoat-FRONT2015 Face to Face 2

Back MWhiteCoat-BCK2015 Face to Face 2

Blade MWhiteCoat-BLD2015 Face to Face 2

Facing MWhiteCoat-FAC2015 Face to Face 2

Top Sleeve MWhiteCoat-TSLV2015 Face to Face 2

Under Sleeve MWhiteCoat-USLV2015 Face to Face 2

Under Collar MWhiteCoat-UCLR46 Face to Face 1

Top Collar MWhiteCoat-TCLR45 Face to Face 2

Pocket MWhiteCoat-PKT40 Face to Face 2

Flap MWhiteCoat-FLAP40 Face to Face 2

Epaulet MWhiteCoat-EPL45 Face to Face 2

3.8 Stitches, seams and stitching. All information relating to stitches, seams and stitching shall conform to ASTM D6193 and shall be in accordance with the operation procedures as specified by the CUF.

3.8.1 Table of operations.

3.8.1.1 Stitching. The process/directions for stitching the Men’s India White coat shall follow current CUF operations and processes. See Appendix A.

3.8.2 Marking. The component parts shall be marked to ensure a uniform shade and size throughout the coat. Any method of shade marking may be used except:

a. Corrosive metal fastening devices.

b. Sew-on type tickets.

c. Adhesive type tickets which leave traces of paper or adhesive on the material upon removal of the tickets.

3.8.3 Use of automated apparel equipment. Automated apparel equipment may be used provided that the finished coat conforms to the required size, dimensions, and configurations.

Patterns may be altered to accommodate the use of automated equipment as specified in 3.8.4.

3.8.4 Manufacturing requirements. The coat shall be cut in accordance with the pattern.

Component parts shall be cut from the same piece (dye lot) of fabric. The use of drill holes on coat is prohibited.

3.9 Cleaning. All loose threads shall be removed. All spots, stains, and marking tickets shall be removed.

3.10 Pressing. The pressing of the coat shall be according to CUF procedures.

3.11 Finished measurements. The finished coat measurements shall conform to the measurements in

Table II when tested as specified in Table III. All measurements are indicated in inches; the coat shall be measured lying flat and smooth, with buttons engaged.

THIS SPACE LEFT INTENTIONALLY BLANK

TABLE II. Finished measurements for Men’s coat (in inches).

Sample

Across

Bottom of

Finished

Collar

Center of

Back from

Bottom collar to bottom of

Finished hem

Finished

Shoulder

Seam

Finished

Sleeve

Under

Sleeve armhole to Sleeve

Hem

Across

Back from

Blade to

Blade

Finished

Coat

Sweep at

Bottom of

Finished

Hem

Across

Front from

Sleeve seam to

Sleeve

Seam

34-R 16.75 28.00 5.75 18.00 15.50 43.00 18.50

35-R 17.00 28.25 5.875 18.00 15.75 44.00 18.75

36-R 17.25 28.50 6.00 18.00 16.00 45.00 19.00

37-R 17.50 28.75 6.125 18.00 16.25 46.00 19.25

38-R 17.75 29.00 6.25 18.00 16.50 47.00 19.5

39-R 18.00 29.25 6.375 18.00 16.75 48.00 19.75

40-R

(BASE) 18.25 29.50 6.50 18.00 17.00 49.00 20.00

41-R 18.5 29.75 6.625 18.00 17.25 50.00 20.25

42-R 18.75 30.00 6.75 18.00 17.50 51.00 20.50

43-R 19.00 30.25 6.875 18.00 17.75 52.00 20.75

44-R 19.25 30.50 7.00 18.00 18.00 53.00 21.00

45-R 19.50 30.75 7.125 18.00 18.25 54.00 21.25

46-R 19.75 31.00 7.25 18.00 18.50 55.00 21.50

47-R 20.00 31.25 7.375 18.00 18.75 56.00 21.75

48-R 20.25 31.50 7.50 18.00 19.00 57.00 22.00

49-R 20.50 31.75 7.625 18.00 19.25 58.00 22.25

50-R 20.75 32.00 7.75 18.00 19.50 59.00 22.50

51-R 21.00 32.25 7.875 18.00 19.75 60.00 22.75

52-R 21.25 32.50 8.00 18.00 20.00 61.00 23.00

53-R 21.50 32.75 8.125 18.00 20.25 62.00 23.25

54-R 21.75 33.00 8.25 18.00 20.50 63.00 23.50

55-R 22.00 33.25 8.375 18.00 20.75 64.00 23.75

COAT LENGTHS

Extra short

XS

Short

S

Regular

R

Long

L

Extra

Long

XL

Extra

Extra

Long

XXL

Grade in Coat Length 26.50 28.00 29.50 31.00 32.50 34.00

Grade in Sleeve Length 17.00 17.50 18.00 18.50 19.00 19.50

NOTE: Collar Height is 1.75 inches for all sizes

3.12 End item requirements. The finished coat shall meet the requirements of Table III when tested as specified in 4.5.3.

TABLE III. End item requirements.

Characteristic Requirement

Dimensional stability, percent (maximum) After two (2) cycles Laundering Warp

Filling

3.0

Dimensional stability, percent (maximum) After two (2) cycles Dry Cleaning Warp Filling

Soil release, rating (minimum) After one (1) laundering cycle

3.5

3.13 Toxicity. Unless otherwise specified in the contract or procurement documents, the finished cloth shall not present a health hazard and shall show compatibility with prolonged, direct skin contact when tested as specified in 4.5.3.

3.14 Workmanship. The finished Men’s India white coat, basic material and components shall conform to the quality and grade established by the purchase description. The occurrence of defects, as specified in 4.5.1, shall not exceed the criteria specified in the contract or purchase order. The coat shall be free of all defects which would affect its serviceability, appearance, and uniformity.

4. VERIFICATION

4.1 Classification of inspections. The inspection requirements specified herein are classified as follows:

a. First article inspection (see 4.2)

b. Conformance inspection (see 4.3)

c. Component and end item inspection (see 4.4)

4.1.1 Inspection conditions. Unless otherwise specified, excluded, amended, modified, or qualified in this PD or applicable procurement documents (see 6.2), all inspections shall be performed in accordance with all the requirements of referenced documents.

4.2 First article inspection. The first article, submitted in accordance with 3.1.1, shall be inspected for design, examined for color and appearance in 3.2, finished dimensions in Table II and 3.11, finished defects in Table IV, and tested as specified in Table V.

4.3 Conformance inspection. Conformance inspection shall include the examination of defects as specified in 4.5.1, finished measurements in 3.11, and the tests in 4.5.3. Sampling for inspection shall be performed in accordance with ASQ/ANSI Z1.4 and Acceptance Quality

Limits (AQL) as defined in the contract and/order, except where otherwise indicated (see 6.2).

4.4 Component and end item inspection. In accordance with 4.1, components and end items shall be tested in accordance with all the requirements of referenced documents unless otherwise excluded, amended, modified or qualified in this document or applicable procurement documents. The Government reserves the right to inspect and test all components and end items to determine conformance to requirements.

4.5 End item examination.

4.5.1 End item visual examination. Each coat shall be visually examined for the defects listed in Table IV. The lot shall be expressed in units of coats. All fabric and garment defects shall be scored in accordance with Table IV, which are clearly visible when examined at a distance of 3-feet and affect serviceability and appearance of the finished coats. Material defects are defined in MIL-STD-1490 and ASTM 3990. If needed, closer inspection shall be conducted to verify compliance with specification requirements.

TABLE IV. End item visual defects.

Material Defect Classification

Major Minor

Material and workmanship

Component part omitted, not cut as specified, distorted, full, tight or twisted; any part of coat caught in any unrelated row of stitching

Hole, cut, tear, smash, burn, drill hole, run, thin place, dye streak, color not as specified, mis-weave, knot or slubs.

Any finished measurement not as specified. 103

Seam: puckered, distorted, pleated, wavy, twisted, irregular or open, loose or tight stitch tension, broken, missing thread or stitch, needle chew, visible mend, edge or raised stitching sewn too close to edge, resulting in damage to cloth seam allowance not as specified, raw edge.

Length of fronts at closure uneven at neck or bottom edge by 1/4-inch or more.

Permanent fold, pleat, or crease 202

Front pockets: not uniform in size or shape, out of horizontal alignment by more than 1/4-inch

Buttons Not specified type, size, or color

Misplaced, omitted, broken or defective

Not attached as specified

Button not aligned with corresponding buttonhole causing gap, puckers, or tightness

TABLE IV. End item visual defects. - Continued

Material Defect Classification

Major Minor

Buttonholes

Any omitted, added, misplaced, ragged edges, caught in other stitching or component, not secured through proper layers of fabric, not serving intended purpose, broken stitches

Not specified size or type, finished cut length not as specified

Shade Shade variation within a part or between parts. 108

Cleanness Spot, stain, thread ends not trimmed or removed.

Rancid odor.

Labels Omitted, incorrect, illegible, misplaced, not attached as specified, or stitched through printing; human readable interpretation (HRI) omitted or illegible; bar code not visible on folded, packaged item.

4.5.2 End item dimensional examination. The Men’s coat shall be examined for conformance to the dimensions specified in 3.11 and the requirements of Table III when tested as specified in 4.5.3. Any dimension not within the specified tolerance shall be classified as a defect. The lot size shall be expressed in units of coats. The inspection and the AQL, expressed in terms of defects per hundred units, shall be as specified in the contract or purchase order.

4.5.3 End item testing. The coats shall be tested according to the test methods specified in

Table V.

TABLE V. End item test methods

Characteristic Requirement Paragraph Test Method

Visual Shade Matching 3.2 4.5.4.1

Presence of Optical Brightener 3.5.1 ASTM D6544

Dimensional stability, After two laundering (2) cycles

3.12 AATCC TM150, (3)(IV)(Aiii)

Dimensional stability, After (2) Dry Cleaning cycles

3.12 AATCC TM158

Soil release grade (min.)

After one (1) laundering cycle

3.12 AATCC TM130

(washing temperature 120 ℉)

Toxicity 3.13 4.5.4.2

4.5.4 Methods of inspection.

4.5.4.1 Visual shade matching. The color and appearance of the Coat shall match the standard sample when viewed using the AATCC EP 9, Option C, (see 6.5) with a primary light source simulating the spectral quality of average daylight, CIE Illuminant D65, with a color temperature of 6500 (± 200) Kelvin (K) illumination of 100 (± 20) foot candles. Alternatively, the color and appearance of the Coat shall match the standard sample with a primary light source simulating artificial daylight, CIE Illuminant D75, with a color temperature of 7500K (± 200) illumination of 100 (± 20) foot candles in lieu of D65. (See 6.5.1). The Coat shall also be a good match to the standard sample with a secondary source simulating the spectral quality of incandescent lamplight, CIE Illuminant A, with a color temperature of 2856K (± 200).

4.5.4.2. Toxicity test. When the toxicity requirement (see 3.13) can be demonstrated with historical use data on the finishing treatments used, toxicity testing may not be required.

(See 6.7 and 6.9).

5. PACKAGING

5.1 Packaging. CUF storage practices for finished garments shall be followed.

6. NOTES

(This section contains information of a general or explanatory nature that may be helpful, but is not mandatory)

6.1 Intended use. The India white coat is intended to be worn by the men in the Corps of

Cadets at the United States Military Academy (USMA) at West Point.

6.2 Acquisition requirements.

a. Title, number, and date of this specification.

b. Sizes required (see 1.2)

c. The specific issue of individual documents referenced (see 2.2 and 2.3).

d. When first article is required (see 3.1.1, 4.2 and 6.3).

e. Conformance inspection (see 3.1.2 and 4.3).

f. Toxicity testing when required (see 3.13 and 4.5.4.2)

g. Inspection conditions (see 4.4)

h. Packaging (see 5.1).

6.3 First article. When a first article inspection is required (see 3.1.1), it will be inspected and approved under the appropriate provisions of FAR 52.209-4. The first article should be a preproduction sample. The contracting officer should specify the appropriate type of first article and the number of units to be furnished. The contracting officer should include specific instructions in acquisition documents regarding arrangements for selection, inspection, and approval of the first article.

6.4 Standard sample. For access to standard samples and patterns contact the following:

ASCE-LWP-CU, Cadet Uniform Factory, 687 Hardee Place, West Point, NY 10996

6.5 Visual shade matching. In 2017, Option A of AATCC Evaluation Procedure 9, Visual

Assessment of Color Difference of Textiles was changed to Option C. NOTE: In case of confusion, the viewing geometry should be “The specimen plane and illumination source will be parallel to each other and aligned so that the light flux is incident at the center of the specimen plane, which is set at a 35 (± 5°) angle relative to the horizontal. The observer will view the specimens at a 90° angle, relative to the plane of the specimens”.

6.5.1 Light source. In 2022, the U.S. Military (All Services) accepted D65 as the new preferred light source for visual shade matching due to the supply chain issues with D75.

DD1222’s should reflect which light source is used. If the light source is not indicated on the

DD1222, D65 will be assumed by the Government Shade Laboratory.

6.6 Known sources.

6.6.1 Thread TH0043 meeting the requirement in 3.6.1.1 is available from Coats

(Astra Tex 40). The Buttonhole gimp TH0015 Both are available from many commercial thread suppliers.

6.6.2 The buttons and toggles in 3.6.2 are available from Waterbury Button.

6.6.3 The hook and eye tapes in 3.6.3 Eye Tape (SOS-Discontinued) part # #8848 Yale

Hook and Eye Style 1-55Z-A21 and Hook Tape (SOS Discontinued) part # 7986 Yale

Hook and Eye Style 8683-A21 are available from Stackry.

6.6.4 The labels (see 3.6.4) are made at the CUF.

6.6.5 Apparel-Lock, Spin fuse, WEB 60" (AP30-60 WE) meets the requirement of 3.5.2.

6.7 Certificate of compliance. The contracting activity may select to accept a certificate of compliance for some requirements.

6.8 Equal item. Prior to the use of an “or equal” item, the contractor shall submit the item with supporting (comparison) data to the contracting officer for approval.

6.9 Toxicity testing. If dermal toxicity testing is required, it will be conducted using Title 40, Protection of Environment, Code of Federal Regulations current edition and applicable sections, which are also consistent with the following OECD tests: Skin Sensitization 406 and Dermal

Irritation 404 (https://www.oecd-ilibrary.org/environment/oecd-guidelines-for-the-testing-of-chemicals-section-4-health-effects_20745788?page=1)

Dermal Sensitization (https://www.law.cornell.edu/cfr/text/40/798.4100

Dermal Toxicity (https://www.law.cornell.edu/cfr/text/40/798.2250 https://www.oecd-ilibrary.org/environment/oecd-guidelines-for-the-testing-of-chemicals-section-4-health-effects_20745788?page=1 https://www.oecd-ilibrary.org/environment/oecd-guidelines-for-the-testing-of-chemicals-section-4-health-effects_20745788?page=1 https://www.law.cornell.edu/cfr/text/40/798.4100 https://www.law.cornell.edu/cfr/text/40/798.2250

6.10 NSN’s

Size NSN

34S

34 R

35 XS 840501Y503200

35 S 840501Y503201

35 R 840501Y503202

35 L 840501Y503259

35XL

36 XS 840501Y503203

36 S 840501Y503204

36 R 840501Y503205

36 L 840501Y503206

36XL

37 XS 840501Y503207

37 S 840501Y503208

37 R 840501Y503209

37 L 840501Y503210

37 XL 840501Y503211

38 XS 840501Y503212

38 S 840501Y503213

38 R 840501Y503214

38 L 840501Y503215

38 XL 840501Y503216

38 XXL 840501Y503264

39XS

39 S 840501Y503217

39 R 840501Y503218

39 L 840501Y503219

39 XL 840501Y503220

39 XXL 840501Y503265

40 XS 840501Y503255

40 S 840501Y503221

40 R 840501Y503222

40 L 840501Y503223

40 XL 840501Y503224

40 XXL 840501Y503266

41 XS 840501Y503257

41 S 840501Y503225

NSN’s Continued

41 R 840501Y503226

41 L 840501Y503227

41 XL 840501Y503228

41 XXL 840501Y503267

42 XS

42 S 840501Y503229

42 R 840501Y503230

42 L 840501Y503231

42 XL 840501Y503232

42 XXL 840501Y503268

43XS

43 S 840501Y503233

43 R 840501Y503234

43 L 840501Y503235

43 XL 840501Y503236

43 XXL 840501Y503269

44 S 840501Y503277

44 R 840501Y503237

44 L 840501Y503238

44 XL 840501Y503239

44 XXL 840501Y503270

45 R 840501Y503240

45 L 840501Y503241

45 XL 840501Y503242

45 XXL 840501Y503271

46 R 840501Y503243

46 L 840501Y503244

46 XL 840501Y503245

46 XXL 840501Y503272

47 R 840501Y503246

47 L 840501Y503247

47 XL 840501Y503256

47 XXL 840501Y503273

48 R 840501Y503248

48 L 840501Y503249

48 XL 840501Y503254

48 XXL 840501Y503274

49 L 840501Y503250

NSN’s Continued

49 XL 840501Y503251

49 XXL 840501Y503275

50 L 840501Y503252

50 XL 840501Y503253

50 XXL 840501Y503276

51 L 840501Y503261

51 XL

52 L 840501Y503262

53 L 840501Y503263

54 XL

Odd Size 840501Y503260

6.11 Subject term key words.

Polyester/Cotton

USMA

West Point

THIS SPACE LEFT INTENTIONALLY BLANK

FIGURE 2. Men’s India White Coat Front.

FIGURE 3. Men’s India White Coat Back.

Custodians: Preparing Activity

Army - GL Army-GL

Reviewing Activity

ASCE-LWP-CU CADET UNIFORM FACTORY, (CUF)