15-B50_Design_Analysis.pdf

100% DESIGN SUBMITTAL

DESIGN ANALYSIS

FOR

REPAIR (SUS), HVAC, CPO; BUILDING 50

SCOTT AIR FORCE BASE, ILLINOIS

PROJECT NO. VDYD 12-1211

A-E CONTRACT NO. FA 4407-14-D-0018

Prepared By:

BIAGI, CHANCE, CUMMINS, LONDON, TITZER, INC.

Consulting Engineers

February 23, 2016

FA440718R0002

Attachment 15

INDEX

I. ARCHITECTURAL

II. PLUMBING

III. HEATING, VENTILATION, AND AIR CONDITIONING

IV. ELECTRICAL

APPENDIX A – CALCULATIONS

APPENDIX B – EQUIPMENT CUT SHEETS

APPENDIX C – CONFIRMATION NOTICES

FA440718R0002

I. ARCHITECTURAL

A. GENERAL PARAMETERS

1. The objective of the project is to reduce energy consumption and increase efficiency of the HVAC in Building 50 at Scott Air Force Base.

Architectural work is to include replacement of ceiling tile with new to facilitate new HVAC throughout building and extending partial height walls at selected offices to above ceiling for acoustical privacy.

B. FUNCTIONAL AND TECHNICAL DATA

1. Design Criteria

a. Unified Facilities Criteria-UFC 1-200-1 General Building

Criteria.

b. International Building Code.

C. DESIGN OBJECTIVES

1. Site

a. No Work

2. Building Upgrade

a. No Work

3. Interior Renovation

a. Replace all ceiling tile. (Proposed product: Armstrong, “Fine Fissured Open Plan," #1754)

b. Replace ceiling grid at offices to receive new walls.

c. Extend walls to above ceiling in rooms 109, 111 and 112.

II. PLUMBING

A. SCOPE

1. Make up water will be provided for the hot water heating system.

B. TECHNICAL REQUIREMENTS

1. Design Criteria.

a. The following technical manuals will be used:

- Military Handbook MIL-HDBK, “Facility Planning and Design

Guide”.

- National Plumbing Code

A. Domestic cold water service will connect to the exiting water service and extend to hot water heating system fill valve assembly.

B. Fire protection heads will be added to provide coverage in the revised office areas (walls to deck areas).

C. Fire protection heads will be removed and reinstalled as required for ceiling pads change out.

III. HEATING, VENTILATION AND AIR CONDITIONING

A. SCOPE

1. The existing HVAC equipment and systems will be removed due to age and condition. Removal work will include existing air handling units, fan coil units, ductwork, hot water heating boiler, pumps, piping and temperature controls.

2. The new HVAC systems will include pumps, air handling units, shut-off variable air volume (VAV) terminal units with hot water reheat coils, ductwork, piping and temperature controls.

3. High efficiency (90%) hot water heater boiler.

B. FUNCTIONAL AND TECHNICAL REQUIREMENTS

1. Design Criteria.

a. The following technical manuals will be used:

- Military Handbook MIL-HDBK-1190, “Facility Planning and Design Guide”.

- ASHRAE Handbook “1993 Fundamentals” and “1992

HVAC Systems and Equipment”.

b. Design Conditions

Outside Design: Winter 6oF

Summer 95oF Dry Bulb 76oF Wet Bulb

Inside Design: Winter 70oF Summer 76oF

30-60% RH

Outside Air Per ASHRAE 62.1

1. Remove pumps, air handling unit, fan coil units, ductwork, diffusers, grilles, piping and temperature controls. Install replacement HVAC systems connected to the existing cooling source and replacement hot water heating boiler.

2. Provide new piping and accessories for supplying hot water to heating coils and chilled water to the cooling coils in the air handling unit and hot water for reheat to the VAV unit heating coils.

3. Provide new pumps. The chilled water will be supplied to the cooling coils in the new air handling units for the cooling coils and hot water will

FA440718R0002

be supplied to the new air handling units for the pre-heat coils and to the terminal unit reheat coils.

4. New hot water heating boiler and integral controls will be installed.

5. Provide new central station air handling unit with pre-heat coil and chilled water coil. Unit will have economizer system for using up to 100% outside air for cooling when outside air conditions permit. Provision for economizer cycle relief air to the exterior will be included.

6. The temperature and air flow to the rooms will be controlled by shut-off variable air volume terminal units. The terminal units will have hot water heating coils.

7. The temperature controls will be DDC with electric valve and damper actuator motors and will tie to existing Base JCI DDC system via BACnet

MSTP.

8. Provide new ductless split system in Computer Room 110 which houses

IT equipment and computers.

D. DESIGN DATA

1. Refer to Appendix B for HVAC equipment data and load estimate calculations.

IV. ELECTRICAL

A. SCOPE

1. Remove and replace building lighting with high efficient LED lighting.

2. Remove electric to HVAC equipment to be replaced and provide electrical to new HVAC equipment.

B. FUNCTIONAL AND TECHNICAL DATA

1. Design Criteria.

a. National Electrical Code - NEC

b. National Fire Protection Association – NFPA

c. International Building Code – IBC

d. Interior Electrical Systems – UFC 3-520-01

e. Grounding Systems – AFI 32-1065

f. Grounding, Bonding and Shielding – MIL-STD-188-124B

g. Illumination Engineering Society of North America – IESNA

h. International Energy Conservation Code IECC 2012

C. EXISTING CONDITIONS

1. Existing Power Distribution

a. Building 50 is served from the base primary electrical distribution system. Electrical service enters the building at 208Y/120 volts, 3-phase, 4-wire solidly grounded wye configuration to a main disconnect switch.

b. Electrical is then routed to a main distribution panels and then to a series of branch circuit breaker panelboards for distribution throughout the building.

c. The lighting source within the building is fluorescent.

D. DESIGN OBJECTIVES

1. Replace the existing lighting fixtures with high efficient LED lighting fixtures.

a. High efficient LED 2x4 lighting fixtures will be provided throughout the majority of the building. 2x2 LED and Led downlights will be provided in selected areas where 2x4 style fixtures are not appropriate.

b. Wall mounted passive infrared (PIR) occupancy sensors will be provided in small individual offices as lighting control.

c. Lighting control in multi-person offices and, restrooms, and other locations where wall sensors would not be appropriate will be provided with ceiling mounted occupancy sensors. PIR ceiling

FA440718R0002

sensors and dual technology (PIR and ultrasonic) ceiling sensors will be provided.

d. Lighting control will be set to be a manual ON and automatic OFF control.

e. Lighting control in the open office area and the large multi-person office will be accomplished through a lighting control panel with a programmed time-of-day schedule where occupancy sensors would not be and effective control.

2. Provide electric to HVAC equipment.

a. Branch circuits will be provided to provide power to the HVAC equipment.

b. Motors will be provided with an appropriate motor controller.

APPENDIX A – CALCULATIONS

PEAK COOLING LOADS

MAIN SYSTEM

By BCCLT

SPACE COIL

SpaceSpaceRoom Supply Space OA

CoilSupply

CoilCoil

Floor Peak LatentSensibleAir Peak Condition Sensible Latent

Area Time LoadLoadBulb Bulb Flow Time DB AirflowDry Bulb Load Load

System ft² Mo/Hr Btu/hBtu/h°F °F cfm Mo/Hr °F Btu/hBtu/hcfm°F

WB

°F

OA

°F °F

WBDB

Condition Dry Dry

Zone Room

Alternative 1 262 18 74 9,254 2,729 54.5 412 75.0 7 74 54.5 2,7297 / 91 412 91/18Peak 101 10,020

256 18 74 5,781 882 54.5 257 75.0 7 74 54.5 8827 / 91 257 91/18Peak 102 6,519

180 15 74 4,264 617 54.5 190 75.0 9 74 54.5 6179 / 91 190 91/15Peak 103 4,499

698 74 19,299 4,228 54.5 858 75.0 74 54.5 4,228 91 858 91 Peak 21,037 Zone - 001

698 18 74 18,057 4,291 54.5 803 75.0 7 74 54.5 4,2917 / 91 803 91/18Block 20,043 Zone - 001

526 16 77 11,522 6,745 54.5 512 75.0 7 77 54.5 6,7457 / 95 512 95/16Peak 104 12,803

219 16 77 1,584 776 54.5 70 75.0 7 77 54.5 7767 / 95 70 95/16Peak 105 2,211

745 77 13,106 7,520 54.5 583 75.0 77 54.5 7,520 95 583 95 Peak 15,014 Zone - 002

745 16 77 13,106 7,520 54.5 583 75.0 7 77 54.5 7,5207 / 95 583 95/16Block 15,014 Zone - 002

158 13 76 3,274 496 54.5 146 75.0 7 76 54.5 4967 / 93 146 93/13Peak 106 3,596

266 16 77 9,073 3,070 54.5 404 75.0 7 77 54.5 3,0707 / 95 404 95/16Peak 107 9,817

424 76 12,348 3,566 54.5 549 75.0 78 54.5 3,566 93 549 95 Peak 13,413 Zone - 003

424 13 76 12,089 3,460 54.5 538 75.0 7 78 54.5 3,6957 / 93 530 95/15Block 13,011 Zone - 003

1,020 18 74 21,444 4,145 54.5 954 75.0 7 74 54.5 4,1457 / 91 954 91/18Peak 108-W Ext 24,487

1,020 74 21,444 4,145 54.5 954 75.0 74 54.5 4,145 91 954 91 Peak 24,487 Zone - 004

1,020 18 74 21,444 4,145 54.5 954 75.0 7 74 54.5 4,1457 / 91 954 91/18Block 24,487 Zone - 004

115 18 74 4,635 467 54.5 206 75.0 7 74 54.5 4677 / 91 206 91/18Peak 109 4,975

115 74 4,635 467 54.5 206 75.0 74 54.5 467 91 206 91 Peak 4,975 Zone - 005

115 18 74 4,635 467 54.5 206 75.0 7 74 54.5 4677 / 91 206 91/18Block 4,975 Zone - 005

1,078 16 77 12,909 5,325 54.5 574 75.0 7 77 54.5 5,3257 / 95 574 95/16Peak 108 - S Cnt 15,589

1,078 77 12,909 5,325 54.5 574 75.0 77 54.5 5,325 95 574 95 Peak 15,589 Zone - 006

1,078 16 77 12,909 5,325 54.5 574 75.0 7 77 54.5 5,3257 / 95 574 95/16Block 15,589 Zone - 006

1,081 16 77 13,857 5,340 54.5 616 75.0 7 77 54.5 5,3407 / 95 616 95/16Peak 108 - Cnt Cnt 16,542

1,081 77 13,857 5,340 54.5 616 75.0 77 54.5 5,340 95 616 95 Peak 16,542 Zone - 007

1,081 16 77 13,857 5,340 54.5 616 75.0 7 77 54.5 5,3407 / 95 616 95/16Block 16,542 Zone - 007

1,078 16 77 21,202 5,325 54.5 943 75.0 7 77 54.5 5,3257 / 95 943 95/16Peak 108 - N Cnt 23,883

1,078 77 21,202 5,325 54.5 943 75.0 77 54.5 5,325 95 943 95 Peak 23,883 Zone - 008

1,078 16 77 21,202 5,325 54.5 943 75.0 7 77 54.5 5,3257 / 95 943 95/16Block 23,883 Zone - 008

439 16 77 5,468 2,169 54.5 243 75.0 7 77 54.5 2,1697 / 95 243 95/16Peak 108 - E Ext 6,712

0 17 76 881 0 54.5 39 75.0 7 76 54.5 07 / 93 39 93/17Peak 108 - E Int 881

122 16 77 1,777 603 54.5 79 75.0 7 77 54.5 6037 / 95 79 95/16Peak 110 2,088

78 12 74 2,298 201 54.5 102 75.0 7 76 54.5 2457 / 91 100 93/13Peak ent 2,412

639 78 10,425 2,972 54.5 464 75.0 78 54.5 3,016 95 461 95 Peak 12,093 Zone - 009

639 15 78 9,974 3,146 54.5 444 75.0 7 78 54.5 3,1467 / 95 444 95/15Block 11,770 Zone - 009

Project Name: TRACE® 700 v6.3.2 calculated at 02:45 PM on 11/12/2015SAFB BLD 50

Dataset Name: 15818-LOAD.trc Peak Clg Loads Main System Report Page 1 of 2

FA440718R0002

SPACE COIL

SpaceSpaceRoom Supply Space OA

CoilSupply

CoilCoil

Floor Peak LatentSensibleAir Peak Condition Sensible Latent

Area Time LoadLoadBulb Bulb Flow Time DB AirflowDry Bulb Load Load

System ft² Mo/Hr Btu/hBtu/h°F °F cfm Mo/Hr °F Btu/hBtu/hcfm°F

WB

°F

OA

°F °F

WBDB

Condition Dry Dry

Zone Room

160 16 77 2,132 790 54.5 95 75.0 7 77 54.5 7907 / 95 95 95/16Peak 111 2,592

303 16 77 3,624 1,497 54.5 161 75.0 7 77 54.5 1,4977 / 95 161 95/16Peak 112 4,492

463 77 5,756 2,287 54.5 256 75.0 77 54.5 2,287 95 256 95 Peak 7,084 Zone - 010

463 16 77 5,756 2,287 54.5 256 75.0 7 77 54.5 2,2877 / 95 256 95/16Block 7,084 Zone - 010

969 18 74 16,010 3,938 54.5 712 75.0 7 76 54.5 4,4467 / 91 706 93/17Peak 108 - N Ext Wall 18,309

969 74 16,010 3,938 54.5 712 75.0 76 54.5 4,446 91 706 93 Peak 18,309 Zone - 011

969 18 74 16,010 3,938 54.5 712 75.0 7 76 54.5 4,4467 / 91 706 93/17Block 18,309 Zone - 011

8,310 74 150,990 45,113 54.5 6,715 75.0 76 54.5 45,666 91 6,707 93 Peak 172,427AHU-1

8,310 18 74 146,444 40,489 54.5 6,513 75.0 7 76 54.5 44,8517 / 91 6,481 93/17Block 168,433AHU-1

0 0 0 0 0 0.0 0 0.0 0 0 0.0 00 / 0 0 0/0Peak113 0

0 0 0 0 0 0.0 0 0.0 0 0 0.0 00 / 0 0 0/0Peak114 0

0 0 0 0 0 0.0 0 0.0 0 0 0.0 00 / 0 0 0/0PeakOut-Str 0

0 0 0 0 0.0 0 0.0 0 0.0 0 0 0 0 Peak 0Heating Only

0 0 0 0 0 0.0 0 0.0 0 0 0.0 00 / 0 0 0/0Block 0Heating Only

Project Name: TRACE® 700 v6.3.2 calculated at 02:45 PM on 11/12/2015SAFB BLD 50

Dataset Name: 15818-LOAD.trc Peak Clg Loads Main System Report Page 2 of 2

FA440718R0002

PEAK HEATING LOADS

MAIN SYSTEM

By BCCLT

SPACE COIL

CoilCoilSupplySpaceSpaceSupplyRoom

SensibleAirDryFloor SensibleAirDryDry

LoadFlowBulbArea LoadFlowBulbBulb

System Btu/hcfm°Fft² Btu/hcfm°F°F

OA Condition

DB

°F

WB

°FPeak Time

Htg Design -4 -6

Zone Room

Block or

Peak

Alternative 1 123 -7,549 110.3 262 75.0 123 -4,772 110.3Peak 101

77 -6,406 130.3 256 75.0 77 -4,672 130.3Peak 102

57 -4,826 131.9 180 75.0 57 -3,547 131.9Peak 103

258 -18,781 121.0 698 75.0 258 -12,991 121.0Peak Zone - 001

258 -18,781 121.0 698 75.0 258 -12,991 121.0Block Zone - 001

154 -9,020 108.0 526 75.0 154 -5,564 108.0Peak 104

21 -2,792 175.0 219 75.0 21 -2,316 175.0Peak 105

175 -11,812 116.1 745 75.0 175 -7,880 116.1Peak Zone - 002

175 -11,812 116.1 745 75.0 175 -7,880 116.1Block Zone - 002

44 -4,725 153.2 158 75.0 44 -3,743 153.2Peak 106

121 -8,345 117.4 266 75.0 121 -5,623 117.4Peak 107

165 -13,070 126.9 424 75.0 165 -9,366 126.9Peak Zone - 003

165 -13,070 126.9 424 75.0 165 -9,366 126.9Block Zone - 003

286 -24,461 132.5 1,020 75.0 286 -18,027 132.5Peak 108-W Ext

286 -24,461 132.5 1,020 75.0 286 -18,027 132.5Peak Zone - 004

286 -24,461 132.5 1,020 75.0 286 -18,027 132.5Block Zone - 004

62 -4,175 116.1 115 75.0 62 -2,785 116.1Peak 109

62 -4,175 116.1 115 75.0 62 -2,785 116.1Peak Zone - 005

62 -4,175 116.1 115 75.0 62 -2,785 116.1Block Zone - 005

172 -15,274 135.4 1,078 75.0 172 -11,402 135.4Peak 108 - S Cnt

172 -15,274 135.4 1,078 75.0 172 -11,402 135.4Peak Zone - 006

172 -15,274 135.4 1,078 75.0 172 -11,402 135.4Block Zone - 006

185 -15,591 131.4 1,081 75.0 185 -11,434 131.4Peak 108 - Cnt Cnt

185 -15,591 131.4 1,081 75.0 185 -11,434 131.4Peak Zone - 007

185 -15,591 131.4 1,081 75.0 185 -11,434 131.4Block Zone - 007

283 -17,763 111.8 1,078 75.0 283 -11,402 111.8Peak 108 - N Cnt

283 -17,763 111.8 1,078 75.0 283 -11,402 111.8Peak Zone - 008

283 -17,763 111.8 1,078 75.0 283 -11,402 111.8Block Zone - 008

73 -8,213 157.2 439 75.0 73 -6,572 157.2Peak 108 - E Ext

12 -1,137 142.7 0 75.0 12 -873 142.7Peak 108 - E Int

24 -2,978 169.0 122 75.0 24 -2,445 169.0Peak 110

31 -4,817 197.8 78 75.0 31 -4,128 197.8Peak ent

139 -17,144 166.9 639 75.0 139 -14,017 166.9Peak Zone - 009

Project Name: TRACE® 700 v6.3.2 calculated at 02:45 PM on 11/12/2015SAFB BLD 50

Dataset Name: 15818-LOAD.trc Peak Htg Loads Main System Report Page 1 of 2

FA440718R0002

SPACE COIL

CoilCoilSupplySpaceSpaceSupplyRoom

SensibleAirDryFloor SensibleAirDryDry

LoadFlowBulbArea LoadFlowBulbBulb

System Btu/hcfm°Fft² Btu/hcfm°F°F

OA Condition

DB

°F

WB

°FPeak Time

Htg Design -4 -6

Zone Room

Block or

Peak

139 -17,144 166.9 639 75.0 139 -14,017 166.9Block Zone - 009

28 -3,080 153.3 160 75.0 28 -2,440 153.3Peak 111

48 -5,702 162.1 303 75.0 48 -4,615 162.1Peak 112

77 -8,782 158.8 463 75.0 77 -7,056 158.8Peak Zone - 010

77 -8,782 158.8 463 75.0 77 -7,056 158.8Block Zone - 010

214 -24,592 159.5 969 75.0 214 -19,789 159.5Peak 108 - N Ext Wall

214 -24,592 159.5 969 75.0 214 -19,789 159.5Peak Zone - 011

214 -24,592 159.5 969 75.0 214 -19,789 159.5Block Zone - 011

2,015 -171,444 132.1 8,310 75.0 2,015 -126,148 132.1Peak AHU-1

2,015 -171,444 132.1 8,310 75.0 2,015 -126,148 132.1Block AHU-1

35 -1,910 125.0 130 75.0 35 -1,910 125.0Peak113

480 -26,323 125.0 707 75.0 480 -26,323 125.0Peak114

104 -5,703 125.0 165 75.0 104 -5,703 125.0PeakOut-Str

619 -33,936 125.0 1,002 75.0 619 -33,936 125.0Peak Heating Only

619 -33,936 125.0 1,002 75.0 619 -33,936 125.0Block Heating Only

Project Name: TRACE® 700 v6.3.2 calculated at 02:45 PM on 11/12/2015SAFB BLD 50

Dataset Name: 15818-LOAD.trc Peak Htg Loads Main System Report Page 2 of 2

FA440718R0002

AHU- 1

BIAGI, CHANCE, CUMMINS, LONDON, TITZER, INC.

Consulting Engineers

Job Name 15818 BLD 50

Place SAFB

WORKSHEET FOR MULTIZONE SYSTEMS

Calculated by : Russel McKinney

DESIRED ACH = 8 Various

DESIRED (SUM)COLD DECK TEMP. (F)= 55 DESIRED (SUM)HOT-DECK TEMP. (F) = 95

DESIRED (WIN) HOT-DECK TEMP. (F) = 95 DESIRED (WIN)COLD-DECK TEMP. (F) = 55

1 2 3 4 5 6 7 8 9 10 11 12 13 14 Cooling Heating MI N MI N

ROOM/ ROOM ROOM SUPPLY EXHAUST O.A. MIN. CFM CFM ROOM CLG. LOAD CLG.LOAD ROOM HTG.LOAD Q O.A. FLOOR CEILING Room Room GPM SUPPLY CFM

ZONE # DESCRIPTION VOLUME ACH ACH ACH Q1 Q1 SENSIBLE LATENT CFM HTG.LOAD CFM SUPPLY CFM AREA HEIGHT Design Design ACH Q1

@ACH @ACH BTU/HR BTU/HR Q2 BTU/HR Q3 CFM @ACH SQ.FT. FT. Temp (F) Temp (F) @ACH

1 101 2620 8 0 350 0 9253 2729 430 - 4766 220 430 0 262 10.00 75 75 1. 6 6 265

1 102 2560 8 0 345 0 5781 882 270 - 4666 215 345 0 256 10.00 75 75 1. 3 6 260

1 103 1800 8 0 240 0 4264 617 200 - 3542 165 240 0 180 10.00 75 75 0. 9 6 180

2 104 5260 8 0 705 0 11522 6745 535 - 5551 260 705 0 526 10.00 75 75 2. 7 6 530

2 105 2190 8 10 295 365 1584 776 75 - 2311 110 295 0 219 10.00 75 75 1. 1 6 220

3 106 1580 8 10 215 265 3274 496 155 - 3739 175 215 0 158 10.00 75 75 0. 8 6 160

3 107 2660 8 0 355 0 9073 3070 420 - 5617 260 420 0 266 10.00 75 75 1. 6 6 270

4 108- W WALL EXT 10200 8 0 1360 0 21444 4145 990 - 18027 835 1360 0 1020 10.00 75 75 5. 2 6 1020

5 109 1150 8 0 155 0 4635 467 215 - 2782 130 215 0 115 10.00 75 75 0. 8 6 115

6 108- S CENTER 10780 8 0 1440 0 12909 5325 595 - 11396 530 1440 0 1078 10.00 75 75 5. 5 6 1080

7 108- MI D CENTER 10810 8 0 1445 0 13857 5340 640 - 11427 530 1445 0 1081 10.00 75 75 5. 5 6 1085

8 108- N CENTER 10780 8 0 1440 0 21202 5325 980 - 11396 530 1440 0 1078 10.00 75 75 5. 5 6 1080

9 108- E WALL EXT 4390 8 0 590 0 5468 2169 255 - 6570 305 590 0 439 10.00 75 75 2. 2 6 440

9 108- E WALL I NT 2370 8 0 320 0 881 0 45 - 873 45 320 0 237 10.00 75 75 1. 2 6 240

9 110 1220 8 0 165 0 1777 603 85 - 2442 115 165 0 122 10.00 75 75 0. 6 6 125

9 ent r ance 780 8 0 105 0 2298 201 110 - 4126 195 195 0 78 10.00 75 75 0. 7 6 80

10 111 1600 8 0 215 0 2131 790 100 - 2437 115 215 0 160 10.00 75 75 0. 8 6 160

10 112 3030 8 0 405 0 3623 1497 170 - 4608 215 405 0 303 10.00 75 75 1. 5 6 305

11 108- N WALL EXT 9690 8 0 1295 0 16010 3938 740 - 19789 915 1295 0 969 10.00 75 75 4. 9 6 970

TOTALS 85470 11440 630 150986 45115 7010 - 126065 5865 11735 0 8547 44. 6 8585

7,010

5,865

11,735

1.37

GPM based on

35F Δ a i r , 20F Δ wat er

CFM/SQ. FT. =

AIR HANDLING UNIT COOLING COIL MAXIMUM CFM =

AIR HANDLING UNIT HEATING COIL MAXIMUM CFM =

AIR HANDLING UNIT OA MIN =

AIR HANDLING UNIT FAN CFM =

FA440718R0002

19.718.525.235.737.634.528.928.435.138.336.328.930.535.935.633.228.733.740.942.336.022.217.611.015.937.143.946.247.748.648.346.339.536.143.047.449.550.850.949.247.044.033.529.034.637.434.930.3

23.220.726.436.037.535.629.628.736.038.536.929.530.336.836.733.329.434.441.243.537.124.521.913.019.042.549.552.053.955.054.852.344.841.449.554.156.257.557.255.252.949.437.632.939.341.938.934.2

27.023.326.034.034.934.028.526.934.236.034.627.928.034.834.931.027.632.538.441.235.626.426.715.122.846.153.656.258.459.759.958.050.847.255.359.561.262.361.959.757.153.340.335.341.944.641.536.7

31.628.226.330.230.930.326.525.030.331.730.826.125.830.931.128.325.929.333.636.433.330.634.517.124.848.756.058.761.062.663.162.458.957.862.163.564.365.265.363.660.956.543.639.044.746.442.737.8

36.337.137.439.840.841.741.641.543.344.144.243.142.944.745.144.443.844.845.846.444.743.044.221.027.550.457.760.462.864.565.264.260.862.365.565.766.166.967.466.565.061.951.145.247.647.343.137.6

38.742.345.648.851.253.054.454.955.355.856.356.556.757.258.058.158.158.558.858.456.553.250.428.730.350.657.660.362.764.264.462.355.654.561.564.065.666.967.867.466.965.757.146.544.642.938.633.7

39.243.848.051.855.257.358.358.458.659.259.759.960.261.062.362.461.762.162.762.561.359.355.652.352.253.053.750.539.332.844.751.053.355.356.456.253.646.343.451.255.557.960.462.262.863.864.757.042.636.735.131.827.8

40.045.449.753.957.860.061.561.862.362.863.663.363.663.866.266.064.365.465.965.763.761.959.157.056.057.057.954.545.333.937.040.842.744.244.844.242.136.333.940.143.746.048.852.455.658.961.557.047.643.942.739.134.5

36.641.945.046.348.950.252.955.354.852.053.656.057.155.756.855.956.058.356.453.253.054.852.148.547.448.653.151.543.933.536.039.141.142.643.042.239.433.331.036.839.840.240.041.147.657.159.151.247.550.951.447.241.4

30.234.437.740.446.348.345.345.543.037.238.843.846.748.653.451.647.446.842.737.138.845.045.945.848.046.546.743.936.531.841.445.848.049.950.549.545.236.834.341.745.444.741.737.340.853.857.045.742.449.551.547.542.1

31.836.540.345.250.653.851.448.645.237.839.645.349.652.557.857.451.849.343.637.039.848.351.653.854.453.751.847.739.233.946.251.654.156.457.456.851.839.635.346.052.651.746.938.139.252.455.844.140.348.251.247.641.9

30.134.337.740.945.947.045.645.042.235.537.042.346.047.752.551.146.945.841.034.937.445.647.648.850.548.248.446.239.336.149.855.458.260.862.262.458.144.338.049.158.357.853.344.343.853.956.342.534.940.643.741.136.3

24.528.131.333.341.343.236.636.133.428.030.034.437.139.447.745.738.336.832.727.829.936.538.239.646.843.539.938.132.133.452.459.162.264.866.165.860.951.147.053.661.461.760.055.453.457.158.743.429.329.430.628.424.9

29.333.737.241.648.450.846.543.840.333.836.241.445.248.255.454.447.244.639.333.335.443.546.549.553.452.047.743.235.835.253.560.363.265.766.865.959.345.340.650.560.160.757.849.147.155.862.256.445.942.139.734.830.0

30.335.039.043.248.949.848.346.543.236.338.443.847.449.954.853.949.147.042.035.737.946.348.751.653.050.949.445.238.034.749.956.358.961.362.461.857.044.238.249.156.856.152.443.842.255.062.863.258.353.548.742.936.9

27.231.134.336.343.144.140.240.137.631.533.037.940.742.749.246.741.740.536.231.033.040.441.943.348.344.242.239.933.628.939.044.045.847.548.347.844.336.232.439.944.343.240.336.941.356.563.462.757.151.345.639.634.1

27.431.033.837.444.345.941.339.236.230.532.437.240.643.451.149.241.739.935.229.931.839.241.544.449.147.543.239.533.027.434.138.039.641.242.040.936.730.031.036.639.439.538.839.047.361.064.561.251.940.233.428.924.7

29.734.338.243.348.249.247.044.040.033.636.241.745.148.453.953.047.244.339.433.535.343.246.750.652.652.049.744.737.231.439.443.946.248.249.447.540.932.639.846.848.650.652.355.060.465.665.961.850.135.031.329.326.3

29.434.037.439.643.845.143.142.940.033.535.841.143.845.348.847.344.343.339.033.235.142.944.745.848.346.846.944.337.233.144.649.952.254.555.853.546.337.046.153.955.557.860.162.564.366.265.761.754.144.139.736.233.1

25.328.931.433.939.040.737.036.033.628.429.834.437.139.345.143.037.436.532.627.929.736.338.440.043.541.840.237.631.731.045.450.853.255.556.854.446.938.148.456.657.859.661.663.364.165.265.061.954.547.142.038.435.2

27.030.934.739.244.146.543.540.336.630.733.338.241.444.549.450.044.340.835.930.432.840.243.546.848.948.145.740.632.730.745.651.353.856.457.855.247.539.150.158.157.556.256.557.257.558.057.756.947.636.035.935.032.1

32.036.740.642.944.747.749.649.045.938.441.347.450.851.050.050.552.150.545.038.140.449.751.651.049.749.952.248.239.632.340.044.947.249.551.049.143.139.352.760.154.445.241.939.638.642.645.750.848.936.733.832.429.6

25.729.431.532.033.134.435.335.633.928.830.134.136.335.435.334.434.435.933.128.930.236.537.636.536.236.640.039.636.234.142.646.948.650.552.152.050.852.260.763.156.145.840.535.232.542.750.356.759.053.047.142.337.6

26.530.132.534.235.934.930.627.525.924.224.125.226.227.631.631.226.926.426.125.526.028.831.735.039.240.941.642.343.446.554.357.658.559.961.562.563.264.665.060.448.942.642.338.036.948.957.260.761.458.853.948.242.7

32.436.940.542.041.237.332.628.627.727.727.928.028.630.432.732.029.729.128.929.229.431.936.339.945.149.051.252.754.356.358.559.760.260.962.063.364.365.364.157.739.829.933.133.337.851.159.462.162.160.256.050.444.2

33.838.642.142.639.532.737.142.047.751.353.555.456.958.158.959.560.160.962.063.865.364.760.746.834.733.531.537.351.960.162.562.160.256.751.044.8

33.838.141.140.836.629.132.637.143.247.850.352.153.654.755.455.756.457.157.960.263.063.762.258.351.947.040.039.052.060.262.662.060.156.851.445.4

33.237.339.939.034.828.028.632.738.142.445.046.848.149.049.649.850.250.751.152.357.060.460.858.654.649.942.039.251.659.862.261.659.656.451.045.2

31.635.738.237.032.926.655.557.957.454.850.842.037.849.357.259.658.957.154.049.043.0

30.033.836.034.730.725.248.553.054.853.851.343.635.742.347.348.748.046.443.839.734.8

27.030.832.931.728.022.943.748.151.152.051.547.539.837.537.336.635.534.232.028.624.8

23.226.428.327.224.019.638.041.444.145.345.443.840.337.035.233.932.731.329.226.122.9

LIGHTING CALCULATIONS

FA440718R0002

APPENDIX B – EQUIPMENT CUT SHEETS

11/11/2015Performance Climate Changer

Job Name

User Name

Address

SAFB 8000 CFM AHU

(H25)Brad Barton

Evansville

Quantity

Job Comments

Performance Climate Changer AHU-2

Module Position: 0Unit level options

Actual airflow 7000 cfm FLA (CV) circuit 2 6.70 A

Unit elevation 0.00 ft MCA circuit 2 8.38 A

Unit size 14 MOP circuit 2 15.07 A

Integral base frame 6in. integral base frame Fuse size circuit 2 15.00 A

UL listed unit UL listed unit Product group Indoor unit

Circuit number 1 Supply fan motor(s) High voltage location Right

FLA (CV) circuit 1 12.50 A Length 187.630 in

MCA circuit 1 15.63 A Width 72.000 in

MOP circuit 1 28.13 A Installed weight 2983.2 lb

Fuse size circuit 1 25.00 A Rigging weight 2890.9 lb

Circuit number 2 Return/booster fan motor(s)

Module Position: 0Controls and VFD/starter

Factory controls package No factory mount Frost protection sensor None

Automatic Selection No auto selection Outside air sensor None

Controller mounting No mount Design sequence - controls H

Controller type No controller Prepackaged solution option used PPS common configuration not used

LCD screen No LCD Total number of control points 0 control points

Module Position: 0Warranty

Warranty section Std. warranty only

1All weights and dimensions are approximate. Certified prints on request.

Unless otherwise noted in the product report, performance is certified in accordance with the AHRI Forced-Circulation Air-Cooling and Air-Heating Coils

Certification Program which is based on AHRI Standard 410 within the Range of Standard Rating Conditions listed in Table 1 of the Standard.

Certified units may be found in the AHRI Directory at www.ahridirectory.org

Air-handling performance data is certified in accordance with AHRI standard 430. Air handlers with plenum fans and vertical draw-thru air handlers where the coil is mounted immediately below the fan section are not covered under the scope of AHRI 430.

FA440718R0002

Module Position: 1Fan section

Fan sec [1]-1

Section type Fan Unit discharge ESP 0.500 in H2O

Fan application Return fan Elevation 0.00 ft

Unit size 14 Minimum temperature 40.00 F

Inlet location Top inlet Design temperature 70.00 F

Fan orientation Front-top discharge Fan size and type 18in. diameter FC, M press

Fan discharge Front top Total brake horsepower 3.546 hp

Side access door location Right Total brake horsepower at min temp 3.759 hp

Drive location Right side drive Total static pressure 2.287 in H2O

Design sequence K2 Speed 888 rpm

Motor horsepower per fan 5 hp Outlet area 2.88 sq ft

Full load motor efficiency 89.50 % Fan outlet velocity 2081 ft/min

Motor class NEMA premium compliant

ODP

Fan module pressure drop 1.000 in H2O

Motor voltage 460/3 Fan discharge loss pressure drop 0.000 in H2O

Cycle 60 cycles/sec Section height 45.000 in

Drive service factor 1.5 fixed drive Section length 42.500 in

Motor RPM 1800 Section width 72.000 in

Fan airflow 6000 cfm Section weight 734.8 lb

Overall ESP 1.000 in H2O Static pressure origin Program calculated

Unit entering ESP 0.500 in H2O

Module Position: 2Air mixing section

Section type Air mixing section Left side opening type No opening

Unit size 14 Design sequence H

Mixing section type reduced length without filter Actuator No

Side access door location Right Opening 1 back - airflow 7000 cfm

Back opening type Full face opening Opening 1 front - airflow 7000 cfm

Back air path Entering Opening 1 top - airflow 7000 cfm

Front opening type Full face opening Opening 1 top total pressure drop 1.287 in H2O

Front air path Leaving Greatest entry PD 1.287 in H2O

Top opening type High velocity parallel damper Opening 1 back - area 16.53 sq ft

Top air path Leaving Opening 1 front - area 16.53 sq ft

Top air path type Exhaust Opening 1 top - area 3.44 sq ft

Top inlet type Unducted Opening 1 top - face velocity 2036 ft/min

Bottom opening type No opening Opening 1 top - pressure drop 1.287 in H2O

Right side opening type No opening

2All weights and dimensions are approximate. Certified prints on request.

Unless otherwise noted in the product report, performance is certified in accordance with the AHRI Forced-Circulation Air-Cooling and Air-Heating Coils

Certification Program which is based on AHRI Standard 410 within the Range of Standard Rating Conditions listed in Table 1 of the Standard.

Certified units may be found in the AHRI Directory at www.ahridirectory.org

Air-handling performance data is certified in accordance with AHRI standard 430. Air handlers with plenum fans and vertical draw-thru air handlers where the coil is mounted immediately below the fan section are not covered under the scope of AHRI 430.

FA440718R0002

Module Position: 3Air mixing section

Section type Air mixing section Actuator No

Unit size 14 Filter condition Mid-life

Mixing section type with filter Filter airflow 7000 cfm

Filter frame 2" Opening 1 back - airflow 7000 cfm

Filter type 1 - run set Pleated media - MERV 8 Opening 1 front - airflow 7000 cfm

Side access door location Right Opening 1 top - airflow 7000 cfm

Back opening type Parallel blade damper Opening 1 back total pressure drop 0.197 in H2O

Back air path Entering Opening 1 top total pressure drop 0.197 in H2O

Back air path type Return Greatest entry PD 0.197 in H2O

Back inlet type Ducted Opening 1 back - area 5.66 sq ft

Front opening type Full face opening Opening 1 back - face velocity 1237 ft/min

Front air path Leaving Opening 1 back - pressure drop 0.197 in H2O

Top opening type Parallel blade damper Opening 1 front - area 16.53 sq ft

Top air path Entering Opening 1 top - area 5.66 sq ft

Top air path type Outside Opening 1 top - face velocity 1237 ft/min

Top inlet type Ducted Opening 1 top - pressure drop 0.197 in H2O

Bottom opening type No opening Filter area 18.06 sq ft

Right side opening type No opening Filter face velocity 388 ft/min

Left side opening type No opening Filter pressure drop 0.606 in H2O

Design sequence H

3All weights and dimensions are approximate. Certified prints on request.

Unless otherwise noted in the product report, performance is certified in accordance with the AHRI Forced-Circulation Air-Cooling and Air-Heating Coils

Certification Program which is based on AHRI Standard 410 within the Range of Standard Rating Conditions listed in Table 1 of the Standard.

Certified units may be found in the AHRI Directory at www.ahridirectory.org

Air-handling performance data is certified in accordance with AHRI standard 430. Air handlers with plenum fans and vertical draw-thru air handlers where the coil is mounted immediately below the fan section are not covered under the scope of AHRI 430.

FA440718R0002

Module Position: 4Coil section

Coil se [4]-1

Section type Horizontal coil Target valve pressure drop 4.00 psig

Unit size 14 Coil type 5W

Section size Small Rows 1

Side access door location None Fin type Prima flo E (energy efficient)

Coil application Heating coil Fin material Aluminum fins

Changeover coil No Tube diameter 5/8in. tube diameter (15.875 mm)

System type Hot water Tube matl/wall thickness .020" (0.508mm) copper tubes

Coil supply/cabinet side Right Turbulators Yes

Coil casing Galvanized Corrosion resistant coating None

Coil height Unit coil height Coil face velocity 560 ft/min

Extended drain and vent Holes only Air pressure drop 0.083 in H2O

Drain pan No drain pan J trap dimension 1.765 in

Design sequence E H trap dimension 3.530 in

Apply AHRI ranges No Leaving fluid temperature 160.00 F

Coil performance airflow 7000 cfm Fluid pressure drop 2.77 ft H2O

Coil elevation 0.00 ft Fluid volume 2.25 gal

Entering dry bulb 45.00 F Fluid velocity 2.36 ft/s

Leaving dry bulb 73.14 F Total cap top or single coil 213.63 MBh

Total capacity 213.63 MBh Coil face area 12.50 sq ft

Nominal fin spacing 80 Per Foot Coil rigging weight 62.2 lb

Entering fluid temperature 180.00 F Coil installed weight 81.0 lb

Fluid temperature drop 20.00 F Coil section pressure drop 0.083 in H2O

Standard fluid flow rate 21.33 gpm Section length 10.000 in

Coil fouling factor 0.00025 hr-sq ft-deg F/Btu Section height 45.000 in

Fluid type Water Section width 72.000 in

Coil fluid percentage 100.00 % Section weight 195.2 lb

Module Position: 5Access section

Section type Access/blank/turning Back opening Full Face

Unit size 14 Design sequence B

Section size Medium Section length 14.000 in

Side access door location Right Section width 72.000 in

Door swing direction Outward swing Section height 45.000 in

Front opening Full Face Section weight 109.4 lb

4All weights and dimensions are approximate. Certified prints on request.

Unless otherwise noted in the product report, performance is certified in accordance with the AHRI Forced-Circulation Air-Cooling and Air-Heating Coils

Certification Program which is based on AHRI Standard 410 within the Range of Standard Rating Conditions listed in Table 1 of the Standard.

Certified units may be found in the AHRI Directory at www.ahridirectory.org

Air-handling performance data is certified in accordance with AHRI standard 430. Air handlers with plenum fans and vertical draw-thru air handlers where the coil is mounted immediately below the fan section are not covered under the scope of AHRI 430.

FA440718R0002

Module Position: 6Coil section

Coil se [6]-1

Section type Horizontal coil Fluid type Water

Unit size 14 Coil fluid percentage 100.00 %

Section size Medium Target valve pressure drop 4.00 psig

Side access door location None Coil type UW

Coil application Cooling coil Rows 6

Changeover coil No Fin type Delta flo E (energy efficient)

System type Chilled water Fin material Aluminum fins

Coil supply/cabinet side Right Tube diameter 1/2in. tube diameter (12.7 mm)

Coil casing Galvanized Tube matl/wall thickness .016" (0.406mm) copper tubes

Coil height Unit coil height Turbulators Yes

Extended drain and vent Holes only Corrosion resistant coating None

Drain pan Galvanized Coil face velocity 513 ft/min

Drain connection location Right Air pressure drop 0.664 in H2O

Design sequence E J trap dimension 2.097 in

Apply AHRI ranges No H trap dimension 4.194 in

Coil performance airflow 7000 cfm Leaving fluid temperature 55.00 F

Coil elevation 0.00 ft Fluid pressure drop 18.86 ft H2O

Entering dry bulb 80.00 F Fluid volume 8.79 gal

Entering wet bulb 67.00 F Fluid velocity 3.76 ft/s

Leaving dry bulb 55.00 F Coil face area 13.65 sq ft

Leaving wet bulb 54.26 F Coil rigging weight 203.0 lb

Sensible capacity 192.91 MBh Coil installed weight 276.5 lb

Total capacity 275.06 MBh Coil section pressure drop 0.664 in H2O

Nominal fin spacing 95 Per Foot Section length 14.000 in

Entering fluid temperature 45.00 F Section height 45.000 in

Fluid temperature rise 10.00 F Section width 72.000 in

Standard fluid flow rate 54.82 gpm Section weight 426.3 lb

Coil fouling factor 0.00000 hr-sq ft-deg F/Btu

5All weights and dimensions are approximate. Certified prints on request.

Unless otherwise noted in the product report, performance is certified in accordance with the AHRI Forced-Circulation Air-Cooling and Air-Heating Coils

Certification Program which is based on AHRI Standard 410 within the Range of Standard Rating Conditions listed in Table 1 of the Standard.

Certified units may be found in the AHRI Directory at www.ahridirectory.org

Air-handling performance data is certified in accordance with AHRI standard 430. Air handlers with plenum fans and vertical draw-thru air handlers where the coil is mounted immediately below the fan section are not covered under the scope of AHRI 430.

FA440718R0002

Module Position: 7Fan section

Fan sec [7]-1

Section type Fan Unit discharge ESP 1.250 in H2O

Fan application Supply fan Elevation 0.00 ft

Unit size 14 Minimum temperature 40.00 F

Inlet location Back inlet Design temperature 70.00 F

Fan orientation Top-back discharge Fan size and type 18in. diameter FC, H press

Fan discharge Top back Total brake horsepower 7.655 hp

Side access door location Right Total brake horsepower at min temp 8.115 hp

Drive location Right side drive Total static pressure 4.050 in H2O

Design sequence K2 Speed 1209 rpm

Motor horsepower per fan 10 hp Outlet area 2.88 sq ft

Full load motor efficiency 91.70 % Fan outlet velocity 2427 ft/min

Motor class NEMA premium compliant

ODP

Fan module pressure drop 2.500 in H2O

Motor voltage 460/3 Fan discharge loss pressure drop 0.000 in H2O

Cycle 60 cycles/sec Section height 45.000 in

Drive service factor 1.5 fixed drive Section length 42.500 in

Motor RPM 1800 Section width 72.000 in

Fan airflow 7000 cfm Section weight 862.2 lb

Overall ESP 2.500 in H2O Static pressure origin Program calculated

Unit entering ESP 1.250 in H2O

6All weights and dimensions are approximate. Certified prints on request.

Unless otherwise noted in the product report, performance is certified in accordance with the AHRI Forced-Circulation Air-Cooling and Air-Heating Coils

Certification Program which is based on AHRI Standard 410 within the Range of Standard Rating Conditions listed in Table 1 of the Standard.

Certified units may be found in the AHRI Directory at www.ahridirectory.org

Air-handling performance data is certified in accordance with AHRI standard 430. Air handlers with plenum fans and vertical draw-thru air handlers where the coil is mounted immediately below the fan section are not covered under the scope of AHRI 430.

FA440718R0002

FS Series

2FSL4

2' x 4'

LED

LED 2FSL42X4

2FSL4

Series Air function Lumens Lens Voltage Driver Color temperature Controls5 Options

2FSL4 2X4 FSL (blank) Static

H Heat removal

30L 30001

40L 40001

48L 48001

60L 60001

72L 72001

(blank) Satin white

(blank) MVOLT

347 3472

EZ1 eldoLED dims to 1%, 0-10V

EZB eldoLED dims to black, 0-10V

EDB eldoLED DALI3

EXB eldoLED DMX/

RDM3

SLD Step-level dimming3,4

EXA1 Dims to 1%, XPoint wireless enabled

EXAB Dims to dark, XPoint wireless enabled

EOHN On/Off (non-dim)

LP830 3000 K

LP835 3500 K

LP840 4000 K

LP850 5000 K

(blank) No controls

N80 nlight® with 80% lumen manage-ment

N80EMG nlight® with 80% lumen manage-ment. For use with generator supply EM power.

N100 nlight® without lumen manage-ment

N100EMG nlight® without lumen manage-ment. For use with generator supply EM power.

EL7L 700 lumen battery pack

EL14L 1400 lumen battery pack

CP Chicago plenum

PWS1836 6' prewire, 3/8" diameter, 18-gauge, 1-circuit

PWS1846 6' prewire, 3/8" diameter, 18-gauge, 2-circuit

RRL_ RELOC®-ready luminaire6

NPLT Narrow pallet

ORDERING INFORMATION Lead times will vary depending on options selected. Consult with your sales representative. Example: 2FSL4 40L EZ1 LP835 N100

Catalog

Number

Notes

Type

FEATURES & SPECIFICATIONS

INTENDED USE — The FS Series recessed LED luminaire combines modern aesthetics and performance in a general lighting product that enables the transformation from fluorescent to

LED. The high efficacy light engine delivers long life and excellent color to ensure a quality lighting installation. Integrated controls options provide for design flexibility and optimum energy savings.

Multiple lumen packages and driver options provide solutions for all your lighting applications.

Certain airborne contaminants can diminish integrity of acrylic. Click here for Acrylic

Environmental Compatibility table for suitable uses.

CONSTRUCTION — Rugged, one-piece cold-rolled steel coated polyester, painted after fabrication. The satin white lens provides excellent shielding and wide distribution. End plates include integral T-bar clips.

Fixture may be mounted and wired in continuous rows. Total fixture height is only 4-3/8".

ELECTRICAL — Long-life LEDs, coupled with high-efficiency drivers, provide superior illumination for extended service life. 90% LED lumen maintenance at 60,000 hours (L90/60,000). The LEDs have a CRI of 82.

eldoLED driver options deliver choice of dimming range, and choices for control, while assuring flicker-free, low-current inrush, 89% efficiency and low EMI.

Optional integrated nLight® controls make each luminaire addressable - allowing it to digitally communicate with other nLight enabled controls such as dimmers, switches, occupancy sensors and photocontrols. Simply connect all the nLight enabled control devices and the FSL luminaires using standard

CAT-5 cabling. Unique plug-and-play convenience allows devices and luminaires to automatically discover each other and self-commission.

Lumen Management: Unique lumen management system (option N80) provides onboard intelligence that actively manages the LED light source so that constant lumen output is maintained over the system life, preventing the energy waste created by the traditional practice of over-lighting.

Step-level dimming option allows system to be switched to 50% power for compliance with common energy codes while maintaining fixture appearance.

Driver disconnect provided where required to comply with US and Canadian codes.

INSTALLATION — Unique grid interfacing arrangement provides mounting into standard 1" and 9/16" tee bar or screw slot grids. 9/16" allows fixture trim to hang level with architectural ceiling tiles. Drywall ceiling adaptors available. Suitable for damp location.

LISTINGS — CSA certified to meet US and Canadian standards. IC rated. DesignLights Consortium® (DLC) qualified product. Not all versions of this product may be DLC qualified. Please check the DLC Qualified

Products List at www.designlights.org/QPL to confirm which versions are qualified.

WARRANTY — 5-year limited warranty. Complete warranty terms located at www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx

Note: Actual performance may differ as a result of end-user environment and application.

All values are design or typical values, measured under laboratory conditions at 25 °C.

Specifications subject to change without notice.

Stock Configurations

2FSL4 40L EZ1 LP835

2FSL4 40L EZ1 LP840

Notes

1 Approximate lumen output.

2 Consult factory for availability. Not available with SLD, EL7L, or EL14L.

3 Not available with N80, N80EMG, N100 or N100EMG.

4 When using prewire option, use PWS1846.

5 nIO access limitations on 30L or EZB.

6 For ordering logic consult: RRL_2013.

Accessories: Order as separate catalog number.

2FS4 F916 Trim to adjust fixture mounting flush with 9/16" T-bar; for 2x4 fixture

DGA24 FS/VT Drywall ceiling adaptor , unit installation

FA440718R0002

2FSL42X4

LED: One Lithonia Way Conyers, GA 30012 Phone: 800-858-7763 Fax: 770-929-8789 www.lithonia.com © 2014-2015 Acuity Brands Lighting, Inc. All rights reserved. Rev. 08/25/15

2FSL4 48L LP835, test no. LTL24699P9, tested in accordance to IESNA LM-79

2FSL4 LED Recessed Lighting 2'x4'

PHOTOMETRICS

2FSL4 40L LP835, test no. LTL24699P5, tested in accordance to IESNA LM-79

0° 20°

40°

60°

80°

90°

0°0°0° 90°

180°

Coefficients of Utilization pf 20% pc 80% 70% 50% pw 70%50%30% 50%30%10% 50%30%10%

R C

R

Zonal Lumen Summary Zone Lumens % Lamp % Fixture 0° - 30° 0° - 40° 0° - 60° 0° - 90° 90° - 180° 0° - 180°

26.9 43.9 77.5

100.0 0.0

100.0

26.9 43.9 77.5

100.0 0.0

100.0

CP Summary 0° 90

0° 5° 15° 25° 35° 45° 55° 65° 75° 85°

0° 20°

40°

60°

80°

90°

0°0°0° 90°

180°

Coefficients of Utilization pf 20% pc 80% 70% 50% pw 70%50%30% 50%30%10% 50%30%10%

R C

R

Zonal Lumen Summary Zone Lumens % Lamp % Fixture 0° - 30° 0° - 40° 0° - 60° 0° - 90° 90° - 180° 0° - 180°

26.9 43.9 77.5

100.0 0.0

100.0

26.9 43.9 77.5

100.0 0.0

100.0

CP Summary 0° 90

0° 5° 15° 25° 35° 45° 55° 65° 75° 85°

Performance Data

Lumen package Input watts 1 Lumens LPW

30L LP830 30.7 3170 103

30L LP835 30.8 3341 108

30L LP840 30.9 3430 111

30L LP850 31.0 3664 118

40L LP830 39.2 3994 102

40L LP835 39.4 4247 108

40L LP840 39.5 4368 111

40L LP850 39.6 4637 117

48L LP830 46.2 4596 100

48L LP835 46.4 4856 105

48L LP840 46.6 4995 107

48L LP850 46.7 5347 115

60L LP830 52.0 5071 98

60L LP835 52.2 5373 103

60L LP840 52.4 5531 106

60L LP850 52.5 5867 112

72L LP830 69.5 6758 97

72L LP835 70.0 6847 98

72L LP840 70.2 7433 106

72L LP850 70.3 7823 111

FA440718R0002

LED: One Lithonia Way Conyers, GA 30012 Phone: 800-858-7763 Fax: 770-929-8789 www.lithonia.com © 2014-2015 Acuity Brands Lighting, Inc. All rights reserved. Rev. 08/25/15

2FSL4 LED Recessed Lighting 2'x4'

Specifications

Length: 48 (122.0)

Width: 24 (61.0)

Depth: 4-3/8 (11.1)

Notes

With nlight 80% lumen management input watts start at 37 and gradually increasing to 46 at 50,000 hrs when using 48L system.

15-3/4 (40)

(61)

4-3/8

(11.1)

Constant Lumen Management Enabled by the embedded nLight control, the FSL actively tracks its run-time and manages its light source such that constant lumen output is maintained over the system life. Referred to as lumen management, this feature eliminates the energy waste created by the traditional practice of over-lighting.

0 10 20 30 40 50

THOUSAND OPERATING HOURS

0 10 20 30 40 50

THOUSAND OPERATING HOURS

POWER INPUT

LIGHT

OUTPUT

100%

80%

100%

80% 37W37W

LI

G

H T

O U

TP

U

T

LI

G

H T

O U

TP

U

T

PO

W

ER

IN

PU

ER

IN

PU

T

Without Lumen Management Energy is wasted and light level is inconsistent.

POWER

INPUT

LIGHT OUTPUT

With Lumen Management Energy is saved and light level remains consistent.

Wasted Energy

Saved Energy

46W 46W

9/16 with accessory 2FS4 F916

9/16 15/16

SS

nLight® Control Accessories:

Order as separate catalog number. Visit www.sensorswitch.com/nLight for complete listing of nLight controls.

WallPod stations Model number Occupancy sensors Model number

On/Off nPODM [color] Small motion 360°, ceiling (PIR / dual tech) nCM 9 / nCM PDT 9

On/Off & Raise/Lower nPODM DX [color] Large motion 360°, ceiling (PIR / dual tech) nCM 10 / nCM PDT 10

Graphic Touchscreen nPOD GFX [color] Wide view (PIR / dual tech) nWV 16 / nWV PDT 16

Photocell controls Model number Wall Switch w/ Raise/Lower (PIR / dual tech) nWSX LV DX / nWSX PDT LV DX

On/Off & Dimming nCM ADCX Cat-5 cables (plenum rated) Model number

10', CAT5 10FT CAT5 10FT J1

15', CAT5 15FT CAT5 15FT J1

MOUNTING DATA DIMENSIONS

All dimensions are inches (centimeters) unless otherwise specified.

FA440718R0002

FS Series

2FSL4

2' x 4'

LED

LED 2FSL42X4

2FSL4

Series Air function Lumens Lens Voltage Driver Color temperature Controls5 Options

2FSL4 2X4 FSL (blank) Static

H Heat removal

30L 30001

40L 40001

48L 48001

60L 60001

72L 72001

(blank) Satin white

(blank) MVOLT

347 3472

EZ1 eldoLED dims to 1%, 0-10V

EZB eldoLED dims to black, 0-10V

EDB eldoLED DALI3

EXB eldoLED DMX/

RDM3

SLD Step-level dimming3,4

EXA1 Dims to 1%, XPoint wireless enabled

EXAB Dims to dark, XPoint wireless enabled

EOHN On/Off (non-dim)

LP830 3000 K

LP835 3500 K

LP840 4000 K

LP850 5000 K

(blank) No controls

N80 nlight® with 80% lumen manage-ment

N80EMG nlight® with 80% lumen manage-ment. For use with generator supply EM power.

N100 nlight® without lumen manage-ment

N100EMG nlight® without lumen manage-ment. For use with generator supply EM power.

EL7L 700 lumen battery pack

EL14L 1400 lumen battery pack

CP Chicago plenum

PWS1836 6' prewire, 3/8" diameter, 18-gauge, 1-circuit

PWS1846 6' prewire, 3/8" diameter, 18-gauge, 2-circuit

RRL_ RELOC®-ready luminaire6

NPLT Narrow pallet

ORDERING INFORMATION Lead times will vary depending on options selected. Consult with your sales representative. Example: 2FSL4 40L EZ1 LP835 N100

Catalog

Number

Notes

Type

FEATURES & SPECIFICATIONS

INTENDED USE — The FS Series recessed LED luminaire combines modern aesthetics and performance in a general lighting product that enables the transformation from fluorescent to

LED. The high efficacy light engine delivers long life and excellent color to ensure a quality lighting installation. Integrated controls options provide for design flexibility and optimum energy savings.

Multiple lumen packages and driver options provide solutions for all your lighting applications.

Certain airborne contaminants can diminish integrity of acrylic. Click here for Acrylic

Environmental Compatibility table for suitable uses.

CONSTRUCTION — Rugged, one-piece cold-rolled steel coated polyester, painted after fabrication. The satin white lens provides excellent shielding and wide distribution. End plates include integral T-bar clips.

Fixture may be mounted and wired in continuous rows. Total fixture height is only 4-3/8".

ELECTRICAL — Long-life LEDs, coupled with high-efficiency drivers, provide superior illumination for extended service life. 90% LED lumen maintenance at 60,000 hours (L90/60,000). The LEDs have a CRI of 82.

eldoLED driver options deliver choice of dimming range, and choices for control, while assuring flicker-free, low-current inrush, 89% efficiency and low EMI.

Optional integrated nLight® controls make each luminaire addressable - allowing it to digitally communicate with other nLight enabled controls such as dimmers, switches, occupancy sensors and photocontrols. Simply connect all the nLight enabled control devices and the FSL luminaires using standard

CAT-5 cabling. Unique plug-and-play convenience allows devices and luminaires to automatically discover each other and self-commission.

Lumen Management: Unique lumen management system (option N80) provides onboard intelligence that actively manages the LED light source so that constant lumen output is maintained over the system life, preventing the energy waste created by the traditional practice of over-lighting.

Step-level dimming option allows system to be switched to 50% power for compliance with common energy codes while maintaining fixture appearance.

Driver disconnect provided where required to comply with US and Canadian codes.

INSTALLATION — Unique grid interfacing arrangement provides mounting into standard 1" and 9/16" tee bar or screw slot grids. 9/16" allows fixture trim to hang level with architectural ceiling tiles. Drywall ceiling adaptors available. Suitable for damp location.

LISTINGS — CSA certified to meet US and Canadian standards. IC rated. DesignLights Consortium® (DLC) qualified product. Not all versions of this product may be DLC qualified. Please check the DLC Qualified

Products List at www.designlights.org/QPL to confirm which versions are qualified.

WARRANTY — 5-year limited warranty. Complete warranty terms located at www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx

Note: Actual performance may differ as a result of end-user environment and application.

All values are design or typical values, measured under laboratory conditions at 25 °C.

Specifications subject to change without notice.

Stock Configurations

2FSL4 40L EZ1 LP835

2FSL4 40L EZ1 LP840

Notes

1 Approximate lumen output.

2 Consult factory for availability. Not available with SLD, EL7L, or EL14L.

3 Not available with N80, N80EMG, N100 or N100EMG.

4 When using prewire option, use PWS1846.

5 nIO access limitations on 30L or EZB.

6 For ordering logic consult: RRL_2013.

Accessories: Order as separate catalog number.

2FS4 F916 Trim to adjust fixture mounting flush with 9/16" T-bar; for 2x4 fixture

DGA24 FS/VT Drywall ceiling adaptor , unit installation

FA440718R0002

LED: One Lithonia Way Conyers, GA 30012 Phone:…