WI_64390__CCTV_Monitoring_System_Installation_Rev._2.pdf

NOAA SHIP RONALD H. BROWN

(R-104)

14 July 2017

ITEM NO. 64390 OPTIONAL ITEM MED/JAL

CCTV System Installation

64390-1

1.0 ABSTRACT

1.1 This item describes the requirement to install a new security video monitoring system.

2.0 REFERENCES:

2.1 Drawing 439-6932759 Closed Circuit Television System Block Diagram

2.2 Drawing 439-001, Security Monitoring System Installation

3.0 ITEM LOCATION/DESCRIPTION: Throughout the ship.

4.0 GOVERNMENT FURNISHED EQUIPMENT/MATERIAL/SERVICE: None.

5.0 NOTES

5.1 The contractor and all subcontractors regardless of tier are advised to review other work items under this contract, including but not limited to 10420to determine their effect on the work required under this work item. Many of the definitions relating to performance of this work item are found in references included in work item 10420.

6.0 QUALITY ASSURANCE: NONE ADDITIONAL.

7.0 STATEMENT OF WORK REQUIRED:

7.1 Remove the existing closed circuit television system utilizing Reference 2.1 for guidance.

7.1.1 Remove all existing cabling.

7.1.2 Remove existing cameras. Turn over equipment to the ship’s

ET.

7.1.3 Remove the CCTV equipment rack, located in the aft bridge.

Grind deck smooth in way of removal.

7.2 Install a new video monitoring system utilizing Reference 2.2 for guidance.

7.2.1 Install cameras in the locations shown in Reference 2.2.

Mount each camera to a junction box and attach each junction box with welded stainless steel studs to associated frames, beams, or structure other than the hull. Manufacture’s installation guidance shall be followed for installation.

Final placement of each camera will be approved by the COR.

The cameras shown on Reference 2.2 are Pelco, or equal.

7.2.1.1 Utilize the manufacture’s mounts and arms as far as

practical. Exterior camera mounts and hardware are to be stainless steel.

NOAA SHIP RONALD H. BROWN

(R-104)

14 July 2017

ITEM NO. 64390 OPTIONAL ITEM MED/JAL

CCTV System Installation

64390-2

7.2.2 Run cables from the cameras to the Computer Lab (1-45-2).

Cables shall be run in cableways and through existing Multi Cable Transits (MCT) when passing through bulkheads or deck to the maximum extent possible. See Reference 2.2 for guidance. All cables shall be low smoke type cables for shipboard use.

7.2.3 Power cables and video cables shall be labeled at each end and at both sides of bulkhead or deck penetrations. Labels shall have the following identification code.

7.2.3.1 Power cable code – SC24VAC-XX (XX = Breaker Number)

7.2.3.2 Video Cable Code – R-TC-XX (XX = sequential number

beginning with 16)

7.2.4 Install two each Digital Video Recorders (DVR) in the

Computer Lab (1-45-2)into an existing electronic rack at frame 62. The DVR’s are to be Pelco DSSRV2-040 4TB or equal.

7.2.5 Install two each Power Supply Modules, Altronix R2416UL or equal, on the aft bulkhead of the Computer Lab (1-45-2).

7.2.6 Connect all camera cables to the video recorders and power supply units following the manufacture’s installation guidance.

7.2.7 The system shall be capable of monitoring and joystick

control from the Bridge and Main Control Station (2-64-1).

7.3 Provide the services of manufacturer’s representative to set up and configure the CCTV system. Representative is to also provide training for operation and troubleshooting of the system.

7.4 The following is a proposed camera equipment list. See reference

2.2 for locations and quantities:

7.4.1 Camera, Pan/Tilt/Zoom INDOOR, Pelco Spectra Mini (Clear

Dome) Model SD4-W1, or equal.

7.4.2 Camera, Pan/Tilt/Zoom OUTDOOR, Pelco Spectra IV SE Dome Pressurized, Model SD429-PRE1 or equal.

7.4.3 Camera, Fixed INDOOR, Pelco Model IS21-CHV10S or equal.

7.4.4 Camera, Fixed OUTDOOR, Pelco Model BU6IRWV506X, or equal.

END OF ITEM