Bldg- 1515 WT 18773888 Removal of Steam Lines.pdf

WORK TASK/CAPITAL PROJECT #:

FACILITY:

REQUESTER:

07 July 2026

(This inspection is valid for three years from the inspection date regardless of Exp. Date of inspector cert. If past this date, a visual or additional assessment will then be required)

LEAD BASED PAINT

ASBESTOS

LIMITED INSPECTION REPORT

Utah Certified State Inspector: Kyle Daly (ASB#-7321: Expires-18 Aug. 2026, PB#-2753: Expires-29 Oct 2028)

INSPECTION DATE: 04 August 2026

Reference UDAQ R307-807-6

DEPARTMENT OF THE AIR FORCE

75TH CIVIL ENGINEERING (CEOHA)

HILL AIR FORCE BASE, UTAH

SIGNATURE:

PREPARED BY: Kyle Daly (ASB#-7321, PB#-2753)

REMOVE STEAM LINES IN EAST MECHANICAL ROOMS

ORGANIZATION:

REQUESTED:

18773888

BRIAN BAILEY

THE QUANTITIES WITHIN THIS REPORT ARE ESTIMATES AND SHOULD

NOT BE USED FOR BIDDING PURPOSES

309 SWEG

FACILITY CONSTRUCTION DATE:

ASBESTOS

N/A

This inspection was performed in accordance with the Utah Division of Air Quality (DAQ) requirements as found in the Utah Air Quality Rule R307-801-10. This inspection report is required to be on site during all abatement, renovation, and demolition activities. Samples referenced in this report were analyzed by polarized light microscopy (PLM) utilizing method 600R-93-116 by Dixon Information (AIHA Acc.#-101579, NVLAP Lab

Code 101012-0) at 78 West 2400 South SLC, Utah 84155 Utah (R307-801-10.8.a-b).

N/A

*LOCATIONS FOUND

N/AN/A

Civil Engineering personnel also reviewed previous asbestos inspection reports of suspect asbestos containing materials (ACM) that could potentially be encountered in the proposed area/areas. The information gathered from all current and previous inspections is shown below by homogenous area (R307-801-9-4).

DEPARTMENT OF THE AIR FORCE

75 CIVIL ENGINEERING (CEOHA)

HILL AIR FORCE BASE, UTAH

The quantities within this report are estimates and are not to be used for bidding purposes.

Table 1

SUMMARY OF ASBESTOS CONTAINING MATERIALS FOUND

MATERIAL TYPE

N/A

*RACM

*Category I *Category II

FRIABILITY QUANTITY

Remove steam lines in east mechanical rooms. Statement of Work:

Category I Non-Friable ACM: Asbestos-containing packings, gaskets, resilient floor coverings, or asphalt roofing products containing more than 1% asbestos as determined by using the method specified in 40 CFR Part 763, Subpart E, Appendix E, Section 1, Polarized Light Microscopy (PLM).

N/A

LIMITED ASBESTOS INSPECTION REPORT INFORMATION

RACM: Regulated Asbestos-Containing Material (RACM)" means friable ACM, Category I non-friable ACM that has become friable, Category I non-friable ACM that will be or has been subjected to sanding, grinding, cutting, or abrading, or Category II non-friable ACM that has a high probability of becoming or has become crumbled, pulverized, or reduced to powder by the forces expected to act on the material in the course of demolition or renovation project operations.

*Per UDAQ definition.

Category II Non-Friable ACM: Any material, excluding Category I non- friable ACM, containing more than 1% asbestos as determined by using the methods specified in 40 CFR Part 763, Subpart E, Appendix E, Section 1, Polarized Light Microscopy (PLM) that, when dry, cannot be crumbled, pulverized, or reduced to powder by hand pressure.

A total of 39 13

Thermal System Pipe Insulation, White Over Yellow, Multiple Locations, 800 Linear Feet

Results

N/A

The following table summarizes the sampling data.

N/A

Table 3.

Thermal System Pipe Lagging Insulation, White Over Yellow suspect materials assessed as part of the inspection.

Sample # samples reference the

N/A

Homogenous Building Material, Description, Thermal System Pipe Fitting Insulation, Tan Over White

Locations found: Locations of building materials as described in this report indicate where they were found, but do not necessarily mean that these are the only locations where these materials may be encountered during the project.

The following is a list of the "Suspect Materials" that were sampled as part of this inspection:

Sample Location

Per EPA requirements, all materials analyzed as containing ≤10% asbestos are point counted utilizing EPA method 600/R-93/116 this information is summarized in Table 2.

Table 2.

ASBESTOS

Thermal System Pipe Insulation, White Over Yellow Thermal System Pipe Fitting Insulation, White Over Yellow Thermal System Pipe Fitting Insulation, White Over White

Thermal System Pipe Insulation, Tan Over Yellow

Sprayed-On Fire Proofing, Grey Thermal System Pipe Saddle Insulation, White Drywall Over Joint Compound Wall System

MATERIAL TYPE

Per Hill AFB requirements, all materials containing any detectable amount of asbestos shall be handled as Asbestos Containing Material (ACM). Table 2 shows the summary of materials containing ≤1% that were identified via "Point Counting". Per EPA/UDAQ

≤1% is not considered to be an asbestos containing material, but special handling/packaging requirements are necessary per OSHA 29CFR 1926.1101 and 29CFR

1910.1001

QUANTITY

N/A

*LOCATIONS FOUND

GM261593

GM261590

Location 1, Phase 1 Mechanical Room

None-Detected

Thermal System Pipe Lagging Insulation, Tan Over Yellow Thermal System Tank Insulation, White Over Yellow Wall Packing, Grey Fire Caulking, Red

Location 1, 2nd Floor Mechanical Room

None-Detected

GM261591

Location 4, Phase One

Mechanical Room None-Detected

GM261592

Location 1, Phase Two

Mechanical Room None-Detected

GM261596

Location 1, Mechanical

Room 196 None-Detected

GM261597

Location 12, Mechanical

Room 196

Thermal System Pipe Insulation, Tan Over Yellow, Multiple Locations, 800 Linear Feet

Thermal System Pipe Fitting Insulation, White Over Yellow, Multiple Locations, 60 Linear

Feet

Thermal System Pipe Fitting Insulation, White Over White, Multiple Locations, 15 Linear Feet

Thermal System Pipe Fitting Insulation, Tan Over White, Multiple Locations, 250 Linear

Feet

Thermal System Pipe Lagging Insulation, White Over Yellow

Thermal System Pipe Lagging Insulation, Tan Over Yellow, Location 11, Mechanical Room 196

GM261602

Location 2, Phase Two

Mechanical Room None-Detected

GM261599

Location 4, 2nd Floor

Mechanical Room None-Detected

GM261600

Location 2, Phase One

Mechanical Room

GM261607

Location 14, Mechanical

Room 196 None-Detected

None-Detected

GM261601

Location 5, Phase One

Mechanical Room None-Detected

None-Detected

GM261606

Location 5, 2nd Floor

Mechanical Room None-Detected

GM261603

Location 1, Mechanical

Room 195 None-Detected

GM261604

Location 2, 2nd Floor

Mechanical Room None-Detected

GM261605

Location 2, Mechanical

Room 196

None-Detected

GM261598

GM261594

Location 2, Mechanical

Room 195 None-Detected

None-Detected

GM261595

Location 4, Mechanical

Room 195 None-Detected

GM261614

Location 5, Mechanical

Room 195 None-Detected

GM261612

Location 6, Phase One

Mechanical Room None-Detected

GM261613

Location 3, Mechanical

Room 196 None-Detected

GM261608

Location 3, Mechanical

Room 195 None-Detected

GM261609

Location 3, Phase One

Mechanical Room None-Detected

GM261610

GM261611

Location 3, Phase Two

Mechanical Room None-Detected

Location 3, Second Floor

Fire Caulking, Red

Thermal System Tank Insulation, White Over Yellow, Wall Packing, Grey

Cell: (801)940-2970 Supervisor: Taylor Brimberry: DSN: (801)586-7094

Asbestos/LBP Shop 75 CES(CEOHA)

Asbestos/LBP Shop Personnel

DSN:(801)777-8006

CONTACT INFORMATION

Table 4.

POTENTIAL FOR ADDITIONAL MATERIALS:

This inspection report only encompasses the areas/materials designated within the scope of work that was provided at the date of inspection (see title page for inspection date). Should the scope of the project be altered in any way or any materials found that are not identified in this report shall require additional assessment. This report cannot be used for any other projects within the building.

Any questions or concerns regarding this inspection report or if any new suspect asbestos containing material (ACM) is encountered, stop work and contact the personnel listed below for further assistance/assessment.

GM261615

Location 7, Phase One

Mechanical Room None-Detected

GM261616

Location 8, Phase One

Mechanical Room None-Detected

GM261621

Location 10, 2nd Floor

Mechanical Room None-Detected

GM261622

North Center, Phase One

Mechanical Room None-Detected

GM261623

Center, Phase One Mechanical Room

GM261624

Southeast, Phase Two

Mechanical Room None-Detected

None-Detected

GM261618

Southwest, Phase Two

Mechanical Room None-Detected

GM261619

Southwest, Phase Two

Mechanical Room None-Detected

GM261620

Location 13, Mechanical

Room 196 None-Detected

Drywall Over Joint Compound Wall System, GM261625

Location 5, Phase Two

Mechanical Room None-Detected

GM261626

Location 11, Phase Two

Mechanical Room None-Detected

GM261627

Location 14, Mechanical

Room 195 None-Detected

Thermal System Pipe Saddle Insulation, White

GM261628

Location 15, Mechanical

Room 196 None-Detected

Sprayed-On Fire Proofing, Grey, GM261617

Location 4, Phase Two

SCOPE OF WORK:

XL Number Substrate Component Color Lead Reading Paint

Condition 3358 Metal T Pipe Red 0.65 Poor 3359 Metal T Pipe Red 0.73 Poor 3360 Metal T Pipe Red 0.65 Poor 3361 Metal T Pipe Red 0.44 Poor 3370 Metal T Pipe Red 1.06 Poor 3378 Metal Valve Handle Yellow 1.07 Poor

XRF Analyzer Used: XRF Analyzer XL3T 600 (Serial #120021)

5-This inspection report only encompasses the areas/materials designated within the scope of work that was provided at the date of the inspection (see title page for date). This report must be modified should the scope of the project be altered in any way or additional materials not previously identified within this report are encountered. This report may not be used for any other projects within the building.

LIMITED LEAD-BASED PAINT IDENTIFICATION REPORT INFORMATION

Table 1.

2-The condition column is the condition only of the painted/coated component (See final page for all readings/samples).

3-The U.S. Department of Housing and Urban Development defines Lead-based paint as any paint, varnish, stain, or other applied coating that has 1 mg/cm² as measured by an X-ray Fluorescence (XRF) Analyzer or laboratory analysis or 0.5 percent by weight (5,000 µg/g by dry weight) by laboratory analysis, or more of lead.

All other components tested were less than 0.80 mg/cm².

4-Any effort to disturb lead paint can create lead dust. Ensure that appropriate abatement, cleanup, and disposal will be accomplished and that appropriate safety measures are taken IAW 29 CFR 1926.62. If you have any questions concerning this report, contact the Asbestos/LBP Shop: Taylor Brimberry at 586-7094.

DEPARTMENT OF THE AIR FORCE

75TH CIVIL ENGINEERING (CEOHA)

HILL AIR FORCE BASE, UTAH

1-Table 1 below, summarizes the painted/coated building components that tested positive for Lead Based Paint/Coating. These components should be segregated or abated prior to renovation or demolition, and a composite TCLP taken of the waste before disposal.

Remove steam lines in east mechanical rooms.

3336 1.05 3379 1.15 3337 1.04 3380 1.16

3338 1.03 POS 3381 1.05

Range: .8 to 1.2 Paint Range: .8 to 1.2 Side Condition Color PbL(mg/cm2) NEG/POS North Fair White 0.01 NEG South Fair White 0.01 NEG South Fair White 0.01 NEG North Good Tan 0.01 NEG North Good Tan 0.01 NEG North Good Tan 0.01 NEG North Good Tan 0.01 NEG North Good Tan 0.01 NEG East Good White 0.01 NEG East Good Tan 0.01 NEG West Good White 0.01 NEG West Good Tan 0.01 NEG North Good White 0.01 NEG North Good Tan 0.01 NEG North Good Grey 0.01 NEG North Poor Black 0.01 NEG North Poor Grey 0.01 NEG North Poor Green 0.01 NEG South Fair Green 0.01 NEG South Poor Red 0.65 NEG South Poor Red 0.73 NEG South Poor Red 0.65 NEG South Poor Red 0.44 NEG South Poor Red 0.01 NEG South Poor Green 0.01 NEG South Poor White 0.01 NEG South Poor Blue 0.01 NEG South Poor White 0.01 NEG South Good Blue 0.01 NEG South Good Red 0.01 NEG

3367 Phase 2 Mechanical Room Coupling Metal 3368 Phase 2 Mechanical Room Elbow Metal

Per 20 Second Reading

Calibration Range

Substrate

Wall Wall Drywall

Drywall

Drywall

Post Calibration

PbL (mg/cm²)

DrywallWall Wall

3347 Room 195 Mechanical Room Wall Block

PbL (mg/cm²) Calibration Range

Model# Serial #

Room/Area Structure

XRF Analyzer XL3T 600 (Serial #120021)

Per 20 Second Reading

Room 196 Mechanical Room Wall Room 196 Mechanical Room Wall Drywall

Drywall

3346 Room 196 Mechanical Room Structural Steel

Room 196 Mechanical Room

Metal

Pre Calibration

XL Number

3345 Room 196 Mechanical Room Structural Steel Metal

Room 196 Mechanical Room

3341 Room 196 Mechanical Room

Room 196 Mechanical Room

3350 Second Floor Mechanical Room Wall Block 3351 Second Floor Mechanical Room Wall Drywall

3348 Room 195 Mechanical Room Wall Block 3349 Second Floor Mechanical Room Wall Block

3354 Second Floor Mechanical Room Small Tank Metal 3355 Second Floor Mechanical Room Pipe Metal

3352 Second Floor Mechanical Room Wall Drywall 3353 Second Floor Mechanical Room Frame Metal

3358 Phase 2 Mechanical Room T Pipe Metal 3359 Phase 2 Mechanical Room T Pipe Metal

3356 Second Floor Mechanical Room Coupling Metal 3357 Phase 2 Mechanical Room Motor Metal

3362 Phase 2 Mechanical Room Pipe Clamp Metal 3363 Phase 2 Mechanical Room Turbine Metal

3360 Phase 2 Mechanical Room T Pipe Metal 3361 Phase 2 Mechanical Room T Pipe Metal

3366 Phase 2 Mechanical Room Wall Brick

3364 Phase 2 Mechanical Room Frame Metal 3365 Phase 2 Mechanical Room Tank Metal

West Good White 0.01 NEG North Poor Red 1.06 POS North Poor Red 0.44 NEG North Poor Green 0.01 NEG North Poor White 0.18 NEG North Poor Yellow 0.01 NEG North Poor White 0.01 NEG North Poor Blue 0.02 NEG North Poor Silver 0.01 NEG North Poor Yellow 1.07 POS

3376 Phase 1 Mechanical Room Tank Metal 3377 Phase 1 Mechanical Room Valve Metal 3378 Phase 1 Mechanical Room Valve Handle Metal

3373 Phase 1 Mechanical Room Pipe Metal 3374 Phase 1 Mechanical Room Stand Metal 3375 Phase 1 Mechanical Room Wall Block

3370 Phase 1 Mechanical Room T Pipe Metal 3371 Phase 1 Mechanical Room Elbow Metal 3372 Phase 1 Mechanical Room Pump Motor Metal

3369 Phase 2 Mechanical Room Wall Brick