Attachment 03e - Electrical Combined (10 pages).pdf

U.S. Department of Veterans Affairs strollo & strollo 718 Virginia Drive

Orlando, FL. 32803 T: (407) 423-5355 F: (407) 422-5994

MES Group, Inc.

550 North Reo Street, Suite 203 Tampa, FL, 33609 813.289.4700 mes group

COA # 8304

ELECTRICAL SYMBOLS AND

LEGENDS

E-000

ELECTRICAL LIGHTING SYMBOLS LEGEND

2X2 FIXTURE - RECESSED, SURFACE, OR PENDANT

MOUNTED - TYPE AS SPECIFIED

2X2 EMERGENCY BRANCH FIXTURE - RECESSED, SURFACE,

OR PENDANT MOUNTED - TYPE AS SPECIFIED

1X4 FIXTURE - RECESSED, SURFACE, OR PENDANT

MOUNTED - TYPE AS SPECIFIED

EXIT SIGN-WALL MOUNTED - TYPE AS SPECIFIED, ARROWS

AS SHOWN ON PLANS

WALL MOUNTED OCCUPANCY SENSOR SWITCH; DUAL

TECHNOLOGY

(PASSIVE INFRARED/ULTRASONIC)

CEILING MOUNTED OCCUPANCY/VACANCY SENSOR;

DUAL TECHNOLOGY

(PASSIVE INFRARED/ULTRASONIC)

EMERGENCY SHUNT RELAY

(UL924 GENERATOR TRANSFER DEVICE)

ROOM CONTROLLER (REFER TO PLANS)

LOCAL WALL DIMMER SWITCH (48" AFF)S

OS VS

RC#

ELCU

(REFER TO LIGHTING FIXTURE SCHEDULE FOR MORE INFORMATION)

D

4' FIXTURE - LINEAR WALL MOUNTED - TYPE AS SPECIFIED

4' FIXTURE - PENDANT LINEAR MOUNTED - TYPE AS

SPECIFIED

VS

DUPLEX RECEPTACLE (18" AFF)

DOUBLE DUPLEX RECEPTACLE (18" AFF)

DUPLEX RECEPTACLE -

CEILING MOUNTED

DOUBLE DUPLEX RECEPTACLE -

CEILING MOUNTED

SIMPLEX RECEPTACLE (18" AFF)

DUPLEX RECEPTACLE 40" AFF OR UON

ELECTRICAL POWER SYMBOLS LEGEND

(MOUNTING HEIGHT TO CENTER LINE OF BOX UNLESS NOTED OTHERWISE)

PANELBOARD

TRANSFORMER

MOTOR CONNECTION - HORSE POWER AS NOTED

DISCONNECT SWITCH - FUSED - FRAME/FUSE/POLES/NEMA

AS NOTED ON PLANS, ALL DISCONNECTS SHALL BE HEAVY

DUTY AND NEMA TYPE 1 U.O.N.

DISCONNECT SWITCH - MOTOR/STARTER COMBINATION

NEMA SIZE TO MATCH HP SHOWN ON PLANS AT THE

SPECIFIED VOLTAGE, HEAVY DUTY

VARIABLE FREQUENCY DRIVE - SEE SPECIFICATIONS

JUNCTION BOX OR PULL BOX - SINGLE GANG U.O.N.

WALL MOUNTED JUNCTION BOX OR PULL BOX - SINGLE

GANG U.O.N.

VFD

SM

30/15/2/3R

DISCONNECT SWITCH - NON-FUSED -

FRAME/FUSE/POLES/NEMA AS NOTED ON PLANS, ALL

DISCONNECTS SHALL BE HEAVY DUTY AND NEMA TYPE 1

U.O.N.

30/2/3R

MOTOR RATED SWITCH WITH THERMAL OVERLOADS FOR

FRACTIONAL HORSEPOWER MOTORS

FLOOR BOX OR POKE THRU JUNCTION OR PULL BOX

VAV WITH ELECTRIC HEAT - KW AS SHOWN

ELECTRIC DUCT HEATER - KW AS SHOWN

VAV X-X

XX KW

EDH X-X

XX KW

J

J

HP

J COMMUNICATION SYMBOLS LEGEND

DATA OUTLET (VERIFY MOUNTING HEIGHT WITH ARCHITECT)

COMMUNICATION CABLE TRAY MOUNTED ABOVE

SUSPENDED CEILING - SIZE AS NOTED ON PLANS

8" CEILING MOUNTED PAGING SPEAKER; PROVIDED WITH

BAFFLE, GRILL AND MATCHING TRANSFORMER

CARD READER. FLUSHED MOUNTED AT 42" AFF.

ELECTRIC DOOR STRIKE

PUSH BUTTON/PUSH PLATE

(MOUNTING HEIGHT TO CENTER LINE OF BOX UNLESS NOTED OTHERWISE)

S

CR

ES

P

REQUEST TO EXITRTE

FIRE ALARM SYMBOLS LEGEND

STROBE LIGHT (80" AFF)

SPEAKER/STROBE COMBINATION (80" AFF)

MAGNETIC DOOR HOLDER (72" AFF)

FIRE ALARM CONTROL PANEL SURFACE OR RECESSED

S

S

DH

FACP FACP

CONDUIT AND WIRING

2A-1,3,5

BRANCH CIRCUIT RUN CONCEALED

BRANCH CIRCUIT RUN UNDER FLOOR

BRANCH CIRCUIT DOWN

BRANCH CIRCUIT UP

HOME RUN TO PANEL 2A SPACES 1, 3, & 5, REFER TO PANEL

SCHEDULES

LINE TYPES

NEW WORK SCOPE OF WORK

EXISTING SCOPE OF WORK

DEMOLITION SCOPE OF WORK

FUTURE SCOPE OF WORK

GENERAL SYMBOLS

KEY NOTE INDICATOR

DRAWING REVISION INDICATORX

X X X X

CODE BLUE STATION (46" AFF)(40" AFF PATIENT BED WALL)

BED NURSE CALL (46" AFF)

NURSE CALL MASTER

NURSE CALL DOME LIGHT (CEILING)

DUTY STATION (46" AFF)

NURSE CALL SYMBOLS LEGEND

ND

NC

C

B

NURSE CALL (46" AFF)

1PH SINGLE-PHASE

1P SINGLE POLE

2/C TWO-CONDUCTOR

3/C THREE-CONDUCTOR

3PH THREE-PHASE

4/C FOUR-CONDUCTOR

4W FOUR-WIRE

A/C UNIT AIR CONDITIONING UNIT

A/E ARCHITECT/ENGINEER

AAP ALARM ANNUNCIATOR PANEL

AC ALTERNATING CURRENT OR ARMORED

CABLE

ACC ACCESSIBLE

ADDL ADDITIONAL

ADJ ADJACENT, ADJOINING

AF AMPERE FRAME OR AMP FUSE

AFC ABOVE FINISHED COUNTER, AUTOMATIC

FREQUENCY CONTROL, OR AVAILABLE

FAULT CURRENT

AFCI ARC-FAULT CURRENT INTERRUPTER

AFF ABOVE FINISHED FLOOR

AFG ABOVE FINISHED GRADE

Ah AMPERE HOUR

AHJ AUTHORITY HAVING JURISDICTION

AIC AMPERE INTERRUPTING CAPACITY

ALT ALTERNATE

AMB AMBIENT

AMP AMPERE

ARCH ARCHITECT

ASC AMPS SHORT CIRCUIT

AT AMPERE TRIP

ATS AUTOMATIC TRANSFER SWITCH

AUTO AUTOMATIC

AV AUDIO VISUAL

BAT BATTERY

BD BOARD

BFF BELOW FINISH FLOOR

BLDG BUILDING

BRKR BREAKER

BYP BY PASS

C CONDUIT

CAB CABINET

CALC CALCULATE

CAP CAPACITY

CAT CATALOG

CATV COMMUNITY ANTENNA TELEVISION

CCR CONTROL CONTACTOR

CCTV CLOSED CIRCUIT TELEVISION

cd CANDELA

CD CONSTRUCTION DOCUMENTS

CF CONTRACTOR FURNISHED

CF/CI CONTRACTOR FURNISHED/CONTRACTOR

INSTALLED

CF/OI CONTRACTOR FURNISHED/OWNER INSTALLED

CFE CONTRACTOR FURNISHED EQUIPMENT

CHW CHILLED WATER

CHWP CHILLED WATER PUMP

CKT CIRCUIT

CKT BRKR CIRCUIT BREAKER

OR C/B

CLF CURRENT LIMITING FUSE

CLG CEILING

COAX COAX CABLE

COMM COMMUNICATION

COMPT COMPARTMENT

CONC CONCRETE

CONT CONTINUE

CONTR CONTRACTOR

COORD COORDINATE

CPT CONTROL POWER TRANSFORMER

CRI COLOR RENDERING INDEX

CT CURRENT TRANSFORMER

CTV CABLE TELEVISION

CU COPPER

CUR CURRENT

dB DECIBEL

DC DIRECT CURRENT

DCP DIMMER CONTROL PANEL

DEG C DEGREES CELSIUS

DEG F DEGREES FAHRENHEIT

DEMO DEMOLITION

DIAG DIAGRAM

DISC DISCONNECT

DISTR PNL DISTRIBUTION PANEL

DMR SW DIMMER SWITCH

DPDT DOUBLE POLE, DOUBLE THROW

DPST DOUBLE POLE, SINGLE THROW

DRSW DOOR SWITCH

DS DISCONNECT SWITCH

DWG DRAWING

EL ELEVATION

ELEC ELECTRIC OR ELECTRICAL

ELEV ELEVATOR

EMER EMERGENCY

EMI ELECTROMAGNETIC INTERFERENCE

EMT ELECTRICAL METALLIC TUBING

ENCL ENCLOSURE

EPO EMERGENCY POWER OFF

EPRF EXPLOSION PROOF

ESMT EASEMENT

EWC ELECTRIC WATER COOLER

EWH ELECTRIC WATER HEATER

EXIST OR EXISTING

(E)

FA FIRE ALARM

FAAP FIRE ALARM ANNUNCIATOR PANEL

FACP FIRE ALARM CONTROL PANEL

FC FOOTCANDLE

FIXT FIXTURE

FLA FULL LOAD AMPS

FLUOR FLUORESCENT

FP FIRE PROTECTION

FT FEET OR FOOT

FU SW FUSED SWITCH

FVNR FULL VOLTAGE NON-REVERSING

FVR FULL VOLTAGE REVERSING

G ELECTRICAL GROUND

GEN GENERATOR

GFCI GROUND FAULT CIRCUIT INTERRUPTER

HID HIGH INTENSITY DISCHARGE

HOA HAND-OFF-AUTOMATIC

HP HORSEPOWER

HT HEIGHT

HZ HERTZ

IESNA ILLUMINATION ENGINEERING SOCIETY OF

NORTH AMERICA

IMC INTERMEDIATE METAL CONDUIT

INCAND INCANDESCENT

IR INFRARED

IWH INSTANTANEOUS WATER HEATER

J-BOX JUNCTION BOX

kV KILOVOLT kVA KILOVOLT AMPERE kVAh KILOVOLT AMPERE PER HOUR kVAR KILOVOLT AMPERE REACTIVE kW KILOWATT kWh KILOWATT HOUR kWhM KILOWATT HOUR METER

LED LIGHT EMITTING DIODE

LF LINEAR FEET (FOOT)

LP LIGHT POLE

LPS LOW PRESSURE SODIUM

LRA LOCKED ROTOR AMPS

LT LIGHT

LTG LIGHTING

LTG PNL LIGHTING PANEL

LTNG LIGHTNING

LV LOW VOLTAGE

MAX MAXIMUM

MC METAL-CLAD

MCA MINIMUM CIRCUIT AMPS

MCB MAIN CIRCUIT BREAKER

MCC MOTOR CONTROL CENTER

MECH MECHANICAL

MH MANHOLE

MIN MINIMUM

MOCP MAXIMUM OVERCURRENT PROTECTION

MLO MAIN LUGS ONLY

MT MOUNT

MTD MOUNTED

MTG MOUNTING

MTS MANUAL TRANSFER SWITCH

MV MEDIUM VOLTAGE

MVA MEGAVOLT-AMPERE

MW MEGAWATT

NA NOT APPLICABLE

NC NORMALLY CLOSED

NEC NATIONAL ELECTRICAL CODE

NEMA NATIONAL ELECTRICAL MANUFACTURERS

ASSOCIATION

NEUT OR N NEUTRAL

NFPA NATIONAL FIRE PROTECTION ASSOCIATION

NIC NOT IN CONTRACT

NL NIGHT LIGHT

NO NORMALLY OPEN

NTS NOT TO SCALE

OC ON CENTER

OD OUTSIDE DIAMETER

OL OVERLOAD

P POLE

PB PULL BOX

PEC PHOTOELECTRIC CELL

PED PEDESTAL

PEND PENDANT

PF POWER FACTOR

PH PHASE

PNL PANEL

PT POTENTIAL TRANSFORMER

PVC POLYVINYL CHLORIDE (PLASTIC)

PWR POWER

RCP REFLECTED CEILING PLAN

REC RECESSED

RECPT RECEPTACLE

RM ROOM

RMS ROOT MEAN SQUARE

REQD REQUIRED

SCC SHORT CIRCUIT CAPACITY

SD SMOKE DETECTOR

SF SQUARE FOOT (FEET)

SHT SHEET

SI INTERNATIONAL SYSTEM OF UNITS

SPEC SPECIFICATION

SPST SINGLE POLE, SINGLE THROW

SURF SURFACE

SW SWITCH

SWBD SWITCHBOARD

SWGR SWITCHGEAR

TEL TELEPHONE

TV TELEVISION

TYP TYPICAL

UFD UNDERFLOOR DUCT

UGND UNDERGROUND

UL UNDERWRITERS LABORATORY

UON UNLESS OTHERWISE NOTED

UPS UNINTERRUPTIBLE POWER SUPPLY

UTIL UTILITY

V VOLT

VA VOLT AMPERE

VAR VOLT AMPERE REACTIVE

VFD VARIABLE FREQUENCY DRIVE

VOLT VOLTAGE

W WATT

WH WATER HEATER

WP WEATHERPROOF

XFER TRANSFER

XFMR TRANSFORMER

ELECTRICAL ABBREVIATIONS GENERAL PROJECT NOTES

1. PANELBOARDS SHALL BE SUPPLIED WITH BOLT-ON CIRCUIT BREAKERS. ALL BUSBARS,

PHASE, NEUTRAL, GROUND IN PANELBOARDS SHALL BE TIN-PLATED ALUMINUM.

2. ALL FINAL LOCATIONS AND ARRANGEMENTS OF LIGHTING FIXTURES SHALL BE OBTAINED

FROM THE ARCHITECTURAL REFLECTED CEILING PLAN.

3. LIGHTING FIXTURES WITH MORE THAN TWO LAMPS SHALL HAVE TWO OUTER LAMPS

CONTROLLED WITH ONE SWITCH AND INNER LAMP(S) CONTROLLED BY A SECOND SWITCH.

4. EACH BRANCH CIRCUIT HOMERUN SHALL HAVE NO MORE THAN THREE CIRCUITS. EACH

BRANCH CIRCUIT HOMERUN SHALL HAVE A SEPARATE GREEN INSULATED EQUIPMENT

GROUNDING CONDUCTOR.

5. THE ELECTRICAL DRAWINGS ARE SCHEMATIC IN NATURE. BEFORE STARTING THE WORK

THE CONTRACTOR SHALL REVIEW ALL OTHER DISCIPLINE DRAWINGS AND VERIFY FIELD

CONDITIONS AND SHALL MAKE ANY REQUIRED MINOR ADJUSTMENTS WITHOUT EXTRA

COST TO THE VA. ANY MAJOR DISCREPANCIES FOUND SHALL BE BROUGHT TO THE

ATTENTION OF THE ARCHITECT/ENGINEER.

Sheet List Table Sheet Number Sheet Title

E-000 ELECTRICAL SYMBOLS AND LEGENDS

ED100 ELECTRICAL DEMOLITION PLAN - FIRST FLOOR

EL100 ELECTRICAL LIGHTING PLAN

EP100 ELECTRICAL POWER PLAN

ET100 ELECTRICAL TELECOMMUNICATIONS PLAN

EY100 ELECTRICAL AUXILIARY SYSTEMS

FA100 FIRE ALARM PLAN

E-500 ELECTRICAL ONE-LINE DIAGRAM

E-600 ELECTRICAL DETAILS

E-700 ELECTRICAL SCHEDULES

FIRE ALARM NOTE

FIRE ALARM DEVICES ARE SHOWN FOR REFERENCE ONLY. FULLY FUNCTIONAL FIRE

ALARM SYSTEM TO INCLUDE FIRE CONTROL PANELS, DIALERS, EXPANDER MODULES,

ANNUNCIATION AND NOTIFICATION DEVICES, WIRING, PROGRAMMING, TESTING,

WARRANTY AND COMMISSIONING SHALL BE INCLUDE IN THIS PROJECT BID. ADDITIONAL

SPACE SHALL BE INCORPORATED INTO THE CURRENT BUILDING TENANT COMPLETE

SPACE. SIGNED AND SEALED DRAWING AND DOCUMENTS AND SEPARATE PERMITTING

SHALL BE PROVIDED BY OTHERS.

RADIOGRAPHIC

CONTROL

A-105

ROOM

HOUSE-

KEEPINGKEEPING

HOUSE-

A-112A-112 A-111A-111

C O R R I D O R

A-104

A-103

C O

R R

I D

O R

A V O

A V O

A V O

A V O

A-148

A-149

A-180

STAIR #6

SIGNAL CLO.

RADIOLOGY

CHIEF

ASSIST. CHIEF

ADMIN..

X RAY ELEVATOR

ROOM

D-103

STOOGE

A V

O

D-1110a

C O

R R

I D

O R

C

-1

STOOGE

C O

R R

I D

O R

LOBBY ELEVATOR

PASSENGER

SIGNAL COLS.

SOILED

R/F ROOM

MULTIPURPOSE

STORAGE

BATHROOM

OFFICE

A-116q

F.H.

I.R.

OFFICE

LOCKER

ROOM

S C

S S

S D

D

S S

D

S D

S

CONTROLS

S C

S C

OS

S S

B S

LINEN

ROOM

BILLING

OFFICE

A-101a

ULTRASOUND

ROOM NO.1

A-101b

SUPERVISOR

OFFICE

HOLDING

RECOVERY

ROOM

A-102

READING

ROOM

A-112a

OFFICE

NO.1

A-101c

OFFICE

NO.2

C-109

UPS

PANEL

1LX (D)

PANEL

1HA(1) (E)

30KVA

XFMR

(R)

XFMR

1LX

75KVA

(E)

XFMR

1LA

75KVA

(E)

PANEL

1LA (D)

PANEL

'ULTRASOUND'

(E)

I J

S

S

I

PANEL

1CP

(D) 3

(TYP)

(TYP)

(TYP)

XFMR

1CP (D)

A-179b

A-179d

ELECTRICAL

ELECTRICAL

(TYP)

(TYP)

U.S. Department of Veterans Affairs strollo & strollo 718 Virginia Drive

Orlando, FL. 32803 T: (407) 423-5355 F: (407) 422-5994

MES Group, Inc.

550 North Reo Street, Suite 203 Tampa, FL, 33609 813.289.4700 mes group

COA # 8304

ELECTRICAL DEMOLITION

PLAN - FIRST FLOOR

ED100

DEMO NOTES

A. EXISTING CONDITIONS ARE BASED ON RECORD DOCUMENTS AND FIELD

OBSERVATION. NOTIFY ENGINEER OF ANY DISCREPANCIES BETWEEN

THESE DRAWINGS AND EXISTING CONDITIONS PRIOR TO DISTURBING

EXISTING INSTALLATION.

B. ALL SERVICE INTERRUPTIONS TO THIS EXISTING FACILITY MUST BE

SCHEDULED AT LEAST 3 WEEKS IN ADVANCE AND BE KEPT TO A

MINIMUM. COORDINATE ALL DISRUPTIVE WORK AND OUTAGE

REQUIREMENTS WITH THE VA/COR.

C. REMOVE EXISTING ELECTRICAL DEVICES, EQUIPMENT, BRANCH

CIRCUITS AND FEEDERS THAT ARE INDICATED FOR DEMOLITION IN THEIR

ENTIRETY BACK TO POINT OF ORIGIN UNLESS OTHERWISE INDICATED.

TURN OFF AND LABEL CIRCUIT BREAKERS AS SPARES FOR NEW WORK

WHERE APPLICABLE.

D. FOR EQUIPMENT WITHIN THE SCOPE OF THIS REMODEL, VERIFY

CONDITION AND AGE OF EXISTING REUSED ELECTRICAL EQUIPMENT,

CIRCUIT BREAKERS, FUSES, CONDUIT, SWITCHES AND RELATED WIRING.

NOTIFY ENGINEER OF ANY ELECTRICAL AND WIRING AGED BEYOND ITS

USEFUL LIFE AND REPLACE AS DIRECTED.

E. ELECTRICAL DRAWINGS ARE DIAGRAMMATIC/SCHEMATIC IN NATURE AND

REPRESENT THE GENERAL SCOPE OF WORK. IT IS NOT WITHIN THE

SCOPE OF THE ELECTRICAL DRAWINGS TO SHOW ALL NECESSARY

RACEWAY ROUTING, BENDS, OFFSETS, PULL BOXES AND

OBSTRUCTIONS. CONTRACTOR SHALL COORDINATE THE FINAL

LOCATION OF EQUIPMENT FOR PROPER OPERATION IN ACCORDANCE

WITH CODE, VA AND MANUFACTURER RECOMMENDATIONS.

F. ELECTRICAL CONTRACTOR SHALL REVIEW OTHER DISCIPLINES

DRAWINGS AND SHALL DISCONNECT AND MAKE SAFE FOR REMOVAL OF

ALL EQUIPMENT SHOWN TO BE DEMOLISHED.

G. DISCONNECT ALL ABANDONED WIRING OF ALL TYPES AT THE

OVERCURRENT PROTECTIVE DEVICE. COMPLETELY REMOVE ALL

ABANDONED WIRING.

H. MAINTAIN AND RESTORE, IF INTERRUPTED, ALL CONDUITS AND

CONDUCTORS PASSING THROUGH AREAS AND SERVICING UNDISTURBED

AREAS.

I. ALL FIRE ALARM DEVICES IN AREAS THAT ARE EXISTING TO REMAIN

SHALL REMAIN OPERATIONAL DURING CONSTRUCTION.

J. ALL DEMOLISHED EQUIPMENT SHALL BE PRESENTED TO VA FOR

FIRST RIGHT OF REFUSAL.

K. EQUIPMENT LABELED AS (E) IS EXISTING TO REMAIN.

L. EQUIPMENT LABELED AS (R) SHALL BE RELOCATED.

M. EQUIPMENT LABELED AS (D) SHALL BE DEMOLISHED.

KEYNOTES

1. EXISTING PANEL '1LA' IS OUTDATED AND SHALL BE REPLACED WITH

NEW ELECTRICAL PANEL TO COMPLY WITH CURRENT CODES. REFER

TO POWER FLOOR PLAN KEYNOTES FOR ADDITIONAL DETAILS.

2. EXISTING PANEL '1LX' IS OUTDATED AND SHALL BE REPLACED WITH

NEW ELECTRICAL PANEL TO COMPLY WITH CURRENT CODES. REFER

TO POWER FLOOR PLAN KEYNOTES FOR ADDITIONAL DETAILS.

3. EXISTING PANEL '1CP' IS OUTDATED AND SHALL BE REPLACED WITH

NEW ELECTRICAL PANEL TO COMPLY WITH CURRENT CODES. REFER

TO POWER FLOOR PLAN KEYNOTES FOR ADDITIONAL DETAILS.

4. TYPICAL FOR ALL ROOMS - DEMOLISH ALL ELECTRICAL EQUIPMENT,

FIRE ALARM DEVICES, RECEPTACLES, DATA DEVICES, JUNCTION

BOXES, ETC. AND ASSOCIATED WIRING AND CONDUIT BACK TO THE

SOURCE, UNLESS OTHERWISE NOTED. ALL DEMOLISHED EQUIPMENT

AND DEVICES SHALL BE RETURNED TO THE VA.

5. TYPICAL FOR ALL ROOMS - LIGHTING FIXTURES AND EXIT SIGNS SHALL

BE DEMOLISHED AND RETURNED TO THE VA. ELECTRICAL CIRCUITS

FROM PANEL '1HA(1)' (ELECTRICAL ROOM A-179b) CURRENTLY FEEDING

NORMAL LIGHTING SHALL REMAIN FOR CONNECTION OF NEW LIGHTING

FIXTURES. EMERGENCY FIXTURES' CONDUIT AND WIRING SHALL BE

DEMOLISHED BACK TO THE SOURCE AND LABELED AS "SPARE" IN

PANEL. NEW EMERGENCY FIXTURES SHALL BE CONNECTED TO

EMERGENCY PANEL '1CP' IN ELECTRICAL ROOM A-179b.

6. CARE SHALL BE EXERCISED WHILE DEMOING FIRE ALARM.

COORDINATE WITH VA SO DEVICES ARE REMOVED FROM THE FIRE

ALARM PANEL PROGRAM. INTENT IS TO AVOID A FALSE ALARM

INCIDENT. GENERAL CONTRACTOR SHALL HAVE WRITTEN APPROVAL

TO PROCEED PRIOR FIRE ALARM REMOVAL COMMENCEMENT.

7. APPROXIMATE LOCATION OF EXISTING PNEUMATIC TUBE SYSTEM.

GENERAL CONTRACTOR SHALL PROTECT TERMINAL DURING DEMO AND

CONSTRUCTION PERIOD. CARE SHALL BE EXERCISED WHILE WORKING

IN THE VICINITY OF THE AREA. SYSTEM TERMINAL FUNCTIONAL TEST

SHALL BE PERFORMED AT THE END OF THE PROJECT. NON PASSING

RESULTS SHALL REQUIRE THE GENERAL CONTRACTOR TO PROVIDE

LABOR AND MATERIAL UNTIL ITS FIXED. PASSING RESULTS SHALL BE

OBTAINED PRIOR GENERATING PANEL REPORT. REPORT SHALL BE

DELIVERED TO COR AS PART OF THE CLOSING DOCUMENTATION

PACKAGE.

ROOM

A-106

CONTROL

A-105

ROOM

HOUSE-

KEEPINGKEEPING

HOUSE-

A-112A-112 A-111A-111

A-104

58.60n.s.f.

77.16n.s.f.

299.00n.s.f.

C O

R R

I D

A V O

A V O

A V O

A V O

C O

R R

I D

O R

C

-1

R/F ROOM

MULTIPURPOSE

CLOSET

EQUIP.

ASSISTANT

BATHROOM

A-116p

AUTOMATION

OFFICE

A-116q

F.H.

LOUNGE/

LOCKER

ROOM

I.R.

OFFICE

PREP/RECOVERY

PREP/RECOVERY

PREP/RECOVERY

READING

AREA

PREP/RECOVERY

SOILED

LINEN

CATHETERS

SUPPLY

PREP/RECOVERY

SCRUB AREA

NURSE

STATION

LINEN

STORAGE

RECLINERS /

OUTPROCESSING100

ENTRY

C-RENO

CORRIDOR

VS

VS

S DS D

AW

b

AW

a

AW

a

AW

c

AW

c b

SD SD

B

B

AW

a

AW

a

AW

a

SDa

SD

b

AW

bAW a

AW

a

AW

c SD a

SD

c

D e

C

C

D e

D e

D f

D f

D f

D f

D e

D f

S D S D

S D

(TYP)

X

X

B

S D

S DVS

RC1

1HA-1

D e

NEW LED LIGHTS TO BE

WRAPPED AROUND

SOFFIT SHALL BE

PROVIDED BY

CONTRACTOR,

SELECTED BY

ARCHITECT.

WATTAGE TO BE

NO MORE THAN

1 W/SQFT

AW

a ca

S D S

D S D e f g e f g kk

B k

B k

B k g g

CB NC

FLOOR

3'-4"

1'-6"

3'-4"

1'-6"

WALL LIGHT. REFER TO PLANS AND

SCHEDULES FOR MORE INFORMATION.

NOTE: HEADWALL SHOWN FOR COORDINATION PURPOSES ONLY

GENERAL CONTRACTOR SHALL COORDINATE ACTUAL HEADWALL REQUIREMENTS

WITH COR AND USE ELECTRICAL PROVISIONS TO CONNECT THEM.

N C N N C N

DEFINITIONS:

CB - CODE BLUE

NC - NURSE CALL

N - NORMAL BRANCH

C - CRITICAL BRANCH

NOTE: REFER TO SPECIFICATION 10 25 13 FOR ADDITIONAL

SYSTEMS LIKE MED GAS, VACUUM SYSTEM, ETC. REFER TO

TYPICAL OUTLET CONFIGURATION FOR OUTLET SHOWN IN

THIS DETAIL.

U.S. Department of Veterans Affairs strollo & strollo 718 Virginia Drive

Orlando, FL. 32803 T: (407) 423-5355 F: (407) 422-5994

MES Group, Inc.

550 North Reo Street, Suite 203 Tampa, FL, 33609 813.289.4700 mes group

COA # 8304

ELECTRICAL LIGHTING PLAN

EL100

GENERAL NOTES

A. ELECTRICAL DRAWINGS ARE DIAGRAMMATIC/SCHEMATIC IN NATURE AND

REPRESENT THE GENERAL SCOPE OF WORK. IT IS NOT WITHIN THE

SCOPE OF THE ELECTRICAL DRAWINGS TO SHOW ALL NECESSARY

RACEWAY ROUTING, BENDS, OFFSET, PULL BOXES AND OBSTRUCTIONS.

CONTRACTOR SHALL COORDINATE THE FINAL LOCATION OF EQUIPMENT

FOR PROPER OPERATION IN ACCORDANCE WITH CODE, OWNER, AND

MANUFACTURER RECOMMENDATIONS.

B. ALL JUNCTION BOXES SHALL BE RIGIDLY ATTACHED TO STRUCTURE OR

MILLWORK.

C. PROVIDE DUAL TECHNOLOGY OCCUPANCY/VACANCY SENSORS FOR

AUTOMATIC LIGHTING CONTROL IN ALL SPACES REQUIRED BY 2020 FBC.

D. LIGHTING CONTROLS CONTRACTOR SHALL PROVIDE CONTROLS AND

SENSORS WITH APPROPRIATE COVERAGE PATTERNS, AND

ADJUSTMENTS OF SENSITIVITY LEVELS TO PREVENT NUCANCE

SWITCHING ON AND OFF OF LIGHTS.

E. THE SYSTEMS SHALL BE A STAND ALONE, NON NETWORKED SYSTEM AS

MANUFACTURED BY WATTSTOPPER, OR O/A/E APPROVED EQUAL.

KEYNOTES

1. REFER TO THIS SHEET, DETAIL #2 FOR LOCATION OF SWITCH ON

PATIENT BED WALL.

FT

NOTE: REFER TO SPECIFICATION 10 25 13 FOR ADDITIONAL

SYSTEMS LIKE MED GAS, VACUUM SYSTEM, ETC.

TYPICAL OUTLET CONFIGURATION SHOWN IN THIS DETAIL.

299.00n.s.f.

302.31n.s.f.

ULTRASOUND

D-111g

WAITING AREA

U

LT

R A

SO

U

N D

S U

IT

E

ULTRASOUND

ROOM NO.6

ULTRASOUND

ROOM NO.5

ULTRASOUND

ROOM NO.4

ULTRASOUND

ROOM NO.3

ULTRASOUND

ROOM NO.2

A V O

A V O

A V O

A V O

D-1115

D-1114

D-1113

X-D1112

D-1110

CIDEX

ROOM

D-1111

A V

O

D-1110a

P-2 P-3

P-1 P-4

D-103C1 -1

151.56n.s.f.

J

J

GFCI

UPS

1LX

ENCLOSURE

PANEL

1HA(1) (E)

30KVA

XFMR

(R)

XFMR

1LX

75KVA

(E)XFMR

1LA

75KVA

(E)

1LA

ENCLOSURE

PANEL

'ULTRASOUND'

(E)

1CP

ENCLOSURE

PREP/RECOVERY

PREP/RECOVERY

PREP/RECOVERY

READING

AREA

PREP/RECOVERY

SOILED

LINEN

CATHETERS

SUPPLY

PREP/RECOVERY

SCRUB AREA

NURSE

STATION

LINEN

STORAGE

RECLINERS /

OUTPROCESSING

ENTRY

CLOS.

ELEC.

A-179b

A-179d

ELECTRICAL

ELECTRICAL

XFMR

1CP

75KVA

(N)

PANEL

1LX (N)

PANEL

1CP (N)

PANEL

1LA (N)

(TYP)

(TYP)

GFCI

GFCI

4 4

EXISTING TUBE SYSTEM

1HA-3 1HA-5

1HA-7

1HA-9

1HA-11

1HA-13

1HA-15

1HA-17

1HA-14

1HA-16 1HA-18

1HA-20

1HA-19

1HA-25

1HA-27

1CP-1 1CP-3

1CP-5

1CP-2

1CP-4

1CP-6

1CP-8

1CP-10

1CP-7

1CP-9

CB NC

FLOOR

3'-4"

1'-6"

3'-4"

1'-6"

WALL LIGHT. REFER TO PLANS AND

SCHEDULES FOR MORE INFORMATION.

NOTE: HEADWALL SHOWN FOR COORDINATION PURPOSES ONLY

GENERAL CONTRACTOR SHALL COORDINATE ACTUAL HEADWALL REQUIREMENTS

WITH COR AND USE ELECTRICAL PROVISIONS TO CONNECT THEM.

N C N N C N ES

DEFINITIONS:

CB - CODE BLUE

NC - NURSE CALL

N - NORMAL BRANCH

C - CRITICAL BRANCH

S - SWITCH FOR LOCAL LIGHT

E - ETHERNET PORTS

N

NOTE: REFER TO SPECIFICATION 10 25 13 FOR ADDITIONAL

SYSTEMS LIKE MED GAS, VACUUM SYSTEM, ETC. REFER TO

TYPICAL OUTLET CONFIGURATION FOR OUTLET SHOWN IN

THIS DETAIL.

U.S. Department of Veterans Affairs strollo & strollo 718 Virginia Drive

Orlando, FL. 32803 T: (407) 423-5355 F: (407) 422-5994

MES Group, Inc.

550 North Reo Street, Suite 203 Tampa, FL, 33609 813.289.4700 mes group

COA # 8304

ELECTRICAL POWER PLAN

EP100

GENERAL NOTES

A. CONTRACTOR SHALL COORDINATE ANY WALL MOUNTED ITEM

(ELECTRICAL/DATA/LIGHTS) WITH ARCHITECT AND OWNER PRIOR TO

INSTALLATION.

B. CONTRACTOR SHALL BE RESPONSIBLE FOR IDENTIFICATION OF ALL

RATED WALLS, CEILINGS, AND SLAB AND THEIR SPECIFIED RATING ON

THE ARCHITECTURAL DRAWINGS. ALL DEVICES AND MATERIAL SHALL

MEET THE UL RATING OF THE RATED WALL ASSEMBLY. CONTRACTOR

SHALL PROVIDE AN ASSEMBLY INSTALLED IN ACCORDANCE WITH UL FOR

THE RATED APPLICATION.

C. REFER TO INTERIOR DESIGNER'S PLANS FOR SPECIFIC DIMENSIONING

REQUIREMENTS FOR ELECTRICAL DEVICES.

D. CIRCUITS SERVED BY GFCI CIRCUIT BREAKERS SHALL BE CIRCUITED

WITH A DEDICATED NEUTRAL CONDUCTOR.

E. WHERE MULTIPLE SWITCHES ARE SHOWN AT THE SAME LOCATION, THEY

SHALL BE GANGED TOGETHER WITH A COMMON GANG PLATE.

F. CABLE AND DATA OUTLETS SHALL BE INSTALLED IN THE SAME 2-PORT

SINGLE-GANG PLATE. EACH CABLE/DATA OUTLET SHALL HAVE A

DEDICATED HOME RUN TO NETWORK PANEL.

KEYNOTES

1. REFER TO THIS SHEET, DETAIL #2 FOR LOCATION OF RECEPTACLES ON

PATIENT BED WALL.

2. THE REPLACEMENT OF THE EXISTING ELECTRICAL PANELS SHALL BE

PHASED OUT TO MINIMIZE THE DISRUPTION OF THE ELECTRICAL

CONNECTIONS TO THE CURRENTLY ACTIVE USER SPACES. THE PHASING

OF THE PANEL RETROFIT SHALL COMMENCE BY INSTALLING THE PANELS

LABELED AS NEW AHEAD OF TIME. ONCE THE NEW PANELS ARE

INSTALLED AND THE CONDUITS ARE RAN TO THE EXISTING PANEL

LOCATIONS, PROCEED TO TEMPORARILY CONNECT THE EXISTING AND

THE NEW PANEL FROM THE SAME FEEDER AND ENERGIZE. THIS IS TO

ALLOW THE STAGGERED ACTIVE CIRCUIT RELOCATION TO COMMENCE.

ONCE ALL THE CONNECTIONS TO THE NEW PANEL ARE IN PLACE, THE

EXISTING PANEL WILL BE DISCONNECTED. PANEL FEEDERS PLANNED TO

BE REUSED SHALL HAVE AN INSULATION TEST PERFORMED AND SHALL

HAVE A PASSING RESULT BEFORE ENERGIZING. A FAILED TEST SHALL

REQUIRE NEW FEEDERS. AS SUCH PROJECT BID SHALL INCLUDE NEW

FEEDERS (MATCHING EXISTING ONES) AND IF NOT USED, SHALL BE

PRESENTED TO THE VA AS A COST DEDUCT. THE EXISTING ENCLOSURE

OF THE DISCONNECTED PANELS ARE NOW SHELTERING THE EXTENDED

ACTIVE CIRCUITS AND SHALL FUNCTION AS A JUNCTION BOX AND SHALL

REMAIN IN PLACE. THIS ENCLOSURE SHALL HAVE AN NTRL LISTED

COVER WITH NO OPENINGS (AND COMPARE WITH THE PANEL

MANUFACTURER). THE PROPOSED COVER SHALL BE APPROVED BY THE

VA AND COR. EACH CIRCUIT POWER OUTAGE SHALL BE COORDINATED

WITH THE COR, TWO WEEKS PRIOR OR AS INDICATED BY THE COR.

LABEL THE COVER AS J BOX FOR '1HA' PANEL FEEDER.

3. EXISTING 30 KVA TRANSFORMER TO BE RELOCATED AT THIS LOCATION

AND SHALL BE MOUNTED ABOVE 75KVA '1CP' TRANSFORMER.

4. PROVIDE ADDITIONAL DEDICATED EQUIPMENT GROUNDING CONDUCTOR

WITH ALL CIRCUITS SERVING EXAM ROOMS FOR CONNECTIONS TO

OUTLETS, SWITCHES, EQUIPMENT, ETC. CONNECTION SHALL BE MADE

BY DEDICATED E.G. BOND METALLIC RACEWAYS, BOXES, ETC., WITH

SEPARATED REDUNDANT EQUIPMENT GROUNDING CONDUCTOR, PER

NEC 517.

5. RECEPTACLES SHOWN FOR CART ON WHEELS (COW) CHARGING

STATION. COORDINATE FINAL LOCATION WITH COR PRIOR ROUGH IN.

6. EXISTING PNEUMATIC TUBE SYSTEM TO REMAIN. REFER TO DEMO NOTES

FOR ADDITIONAL DETAILS.

7. FURNISH AND INSTALL A NEW POWER OUTLET FOR THE WALL CLOCK AS

SHOWN. EXACT INSTALLATION HEIGHT OF THIS OUTLET A.F.F SHALL BE

COORDINATED IN FIELD BY THE CONTRACTOR WITH THE ARCHITECT.

NOTE: REFER TO SPECIFICATION 10 25 13 FOR ADDITIONAL

A-106

CONTROL

A-105

ROOM

HOUSE-

KEEPINGKEEPING

HOUSE-

A-112A-112 A-111A-111

A-104

299.00n.s.f.

C O

R R

I D

C

R R

I D

R R

I D

O R

C

-1

R/F ROOM

MULTIPURPOSE

CLOSET

EQUIP.

ASSISTANT

BATHROOM

A-116p

AUTOMATION

OFFICE

A-116q

F.H.

LOUNGE/

LOCKER

ROOM

I.R.

OFFICE

PREP/RECOVERY

PREP/RECOVERY

PREP/RECOVERY

READING

AREA

PREP/RECOVERY

SOILED

LINEN

CATHETERS

SUPPLY

PREP/RECOVERY

SCRUB AREA

NURSE

STATION

LINEN

STORAGE

RECLINERS /

OUTPROCESSING100

ENTRY

C-RENO

CORRIDOR

4D 4D

4D

4D

4D4D

4D

4D

4D

WAP

1 6

1 6

4 7

8 (TYP)

4D

4D

W. BATH.ROOM 5

165.57n.s.f.

M. BATH.

DRESSING

DRESSING

A-130d

HISTOPATHOLOGY

ELEC. CLOS.

43.14n.s.f.

95.60n.s.f.

BATHROOM

A-135

.5

0n .s

.f.

A-132b

BATH.

A-136

426.90n.s.f.

A-123

C O R R I D O R

BIO HAZARD

300.15n.s.f.

A-131

303.43n.s.f.

RADIOGRAPHIC

A-132

ROOM 3

302.02n.s.f.

115.02n.s.f.

C O R R I D O R

88.04n.s.f. 83.22n.s.f.

6970.67n.s.f.

548.15n.s.f.

A-127

STORAGE

A-125

BATHROOM

MAN'S

A-126

W. BATH

347.37n.s.f.

BIO CHEMISTRY

A-128

418.11n.s.f.

A-143

LIGHT AREA

99.45n.s.f.

ROOMDIAGNOSTIC

RADIOGRAPHIC

170.08n.s.f.

A-139

283.42n.s.f.

THERAPY

A-187

RADIATION

62.88n.s.f.

STORAGE

A-137b FILM

RADIOGRAPHIC

ROOM 4

135.51n.s.f.

A-142

DARK ROOM

BATH

486.16n.s.f.

RADIOGRAPHIC

ROOM 1

A-131

ELCT. CL.

RADIOLOGIST

CONSULTATION

A-146

182.72n.s.f.

CLERKS &

A-116Ig

SPEC.

A-116d

TOILET

63.68n.s.f.

STORAGE

A-116e

FILES

RADIOGRAPHIC

ROOM

A-106

CONTROL

A-105

ROOM

HOUSE-

KEEPINGKEEPING

HOUSE-

A-112A-112 A-111A-111

A-104

299.00n.s.f.

ROOM

CONFERENCE

A-129

C O

R R

I D

208.47n.s.f.

WAITING

A-147a

AREA

C O

R R

I D

172.06n.s.f.

159.77n.s.f.

C O

R R

I D

O R

LABORATORY

R/F ROOM

MULTIPURPOSE

CLOSET

EQUIP.

ASSISTANT

BATHROOM

A-116p

AUTOMATION

OFFICE

A-116q

F.H.

LOUNGE/

LOCKER

ROOM

I.R.

OFFICE

PREP/RECOVERY

PREP/RECOVERY

PREP/RECOVERY

READING

AREA

PREP/RECOVERY

SOILED

LINEN

CATHETERS

SUPPLY

PREP/RECOVERY

SCRUB AREA

NURSE

STATION

LINEN

STORAGE

RECLINERS /

OUTPROCESSING100

ENTRY

C-RENO

CORRIDOR

2 4 7

CB NC

FLOOR

3'-4"

1'-6"

3'-4"

1'-6"

WALL LIGHT. REFER TO PLANS AND

SCHEDULES FOR MORE INFORMATION.

WALL LIGHT. REFER TO PLANS AND

SCHEDULES FOR MORE INFORMATION.

NOTE: HEADWALL SHOWN FOR COORDINATION PURPOSES ONLY

GENERAL CONTRACTOR SHALL COORDINATE ACTUAL HEADWALL REQUIREMENTS

WITH COR AND USE ELECTRICAL PROVISIONS TO CONNECT THEM.

N C N N C N

DEFINITIONS:

CB - CODE BLUE

NC - NURSE CALL

N - NORMAL BRANCH

C - CRITICAL BRANCH

NOTE: REFER TO SPECIFICATION 10 25 13 FOR ADDITIONAL

SYSTEMS LIKE MED GAS, VACUUM SYSTEM, ETC.

TYPICAL OUTLET CONFIGURATION SHOWN IN THIS DETAIL.

U.S. Department of Veterans Affairs strollo & strollo 718 Virginia Drive

Orlando, FL. 32803 T: (407) 423-5355 F: (407) 422-5994

MES Group, Inc.

550 North Reo Street, Suite 203 Tampa, FL, 33609 813.289.4700 mes group

COA # 8304

ELECTRICAL

TELECOMMUNICATIONS PLAN

ET100

GENERAL NOTES

A. EXISTING CONDITIONS ARE BASED ON RECORD DOCUMENTS AND FIELD

OBSERVATION. ELECTRICAL CONTRACTOR SHALL REPORT

DISCREPANCIES TO ENGINEER PRIOR TO DISTURBING EXISTING

INSTALLATION.

B. PROVIDE JUNCTION BOXES, WIRE, CABLING, CONDUIT, ETC, AS

REQUIRED TO MAINTAIN CONTINUITY TO EXISTING TO REMAIN DEVICES,

FIXTURES, EQUIPMENT, ETC.

C. ALL UNUSED OR ABANDONED WIRE, CONDUIT, CABLING, ETC. SHALL BE

REMOVED BACK TO POINT OF ORIGIN.

D. THE CONTRACTOR IS RESPONSIBLE FOR ALL TELE/DATA CONDUIT,

WIRING, TERMINATIONS, ANY REQUIRED PATCH PANELS, ETC.

NECESSARY FOR ALL SPECIAL SYSTEMS IN COORDINATION WITH THE VA

OIT DEPARTMENT, UNLESS OTHERWISE NOTED.

E. JUNCTION BOXES SHALL BE MOUNTED IN ACCESSIBLE LOCATIONS.

PROVIDE AND COORDINATE ACCESS PANELS IN HARD CEILINGS WITH

ARCHITECTURAL REFLECTED CEILING PLAN.

F. CONTRACTOR SHALL TERMINATE CABLING AND PERFORM INITIAL

CONFIGURATION OF ALL NEWLY INSTALLED HARDWARE / SYSTEM

SOFTWARE LOCATED IN THE SECURITY AND SURVEILLANCE ROOMS.

G. FINAL MOUNTING HEIGHTS AND LOCATIONS OF BOXES, JUNCTION BOXES

AND DATA CONNECTIONS SHALL BE VERIFIED WITH VENDORS AND VA

PRIOR TO CONSTRUCTION.

KEYNOTES

1. PROVIDE JUNCTION BOX FOR DATA FURNITURE WHIP TO PREWIRED

FURNITURE.

2. PROVIDE BASKET - 12" WIDE x 2" DEPTH CABLE TRAY. WIRE MESH SPACING SHALL NOT EXCEED 2" x 4." FURNISH AND INSTALL WITH A

CONTINUOUS BARRIER STRIP FOR ENTIRE TRAY ROUTE TO PROVIDE

PARTITION FOR NURSE CALL AND OTHER CLASS LIMITED POWER

CIRCUITS.

3. PROVIDE (1) 2" CONDUIT SLEEVE FOR DATA CABLE PENETRATION THRU

WALL.

4. CABLE TRAY SHALL BE MOUNTED ABOVE DROP ACCESSIBLE CEILING.

COORDINATE FINAL CONNECTIONS TO DATA EQUIPMENT IN ELEC ROOM

AND VERIFY ROUTING AND CABLE TRAY SIZING WITH VA OIT

DEPARTMENT.

5. ROUTE CAT6A CABLE BACK TO DATA RACKS IN ELEC CLOSET AS SHOWN

ON ET100 - 2.

6. DATA RECEPTACLES ARE SHOWN FOR REFERENCE ONLY. PROVIDE DATA

CONNECTION TO FURNITURE SYSTEMS PER MANUFACTURER

RECOMMENDATIONS. REFER TO ELECTRICAL POWER PLAN EP101 FOR

MORE INFORMATION.

7. PROVIDE CABLE TRAY PARTITION TO SEPARATE NURSE CALL CLASS 2

WIRING FROM ALL OTHER SYSTEM CONDUCTORS.

8. REFER TO THIS SHEET, DETAIL #3 FOR LOCATION OF DATA DEVICE ON

PATIENT BED WALL.

A-106

CONTROL

A-105

ROOM

HOUSE-

KEEPINGKEEPING

HOUSE-

A-112A-112 A-111A-111

A-104

299.00n.s.f.

C O

R R

I D

R R

I D

O R

C

-1

R/F ROOM

MULTIPURPOSE

CLOSET

EQUIP.

ASSISTANT

BATHROOM

A-116p

AUTOMATION

OFFICE

A-116q

F.H.

LOUNGE/

LOCKER

ROOM

I.R.

OFFICE

PREP/RECOVERY

PREP/RECOVERY

PREP/RECOVERY

READING

AREA

PREP/RECOVERY

SOILED

LINEN

CATHETERS

SUPPLY

PREP/RECOVERY

SCRUB AREA

NURSE

STATION

LINEN

STORAGE

RECLINERS /

OUTPROCESSING100

ENTRY

C-RENO

CORRIDOR

CR

RTE

C R

R

TE

C R

R

TE

ES

ES

ES

P

C B C B

C

NC NC

D B

C B

CBCB

N D

N D

S

S

S

ND

C

CB NC

FLOOR

3'-4"

1'-6"

3'-4"

1'-6"

WALL LIGHT. REFER TO PLANS AND

SCHEDULES FOR MORE INFORMATION.

NOTE: HEADWALL SHOWN FOR COORDINATION PURPOSES ONLY

GENERAL CONTRACTOR SHALL COORDINATE ACTUAL HEADWALL REQUIREMENTS

WITH COR AND USE ELECTRICAL PROVISIONS TO CONNECT THEM.

DEFINITIONS:

CB - CODE BLUE

NC - NURSE CALL

N - NORMAL BRANCH

C - CRITICAL BRANCH

N C N N C N

NOTE: REFER TO SPECIFICATION 10 25 13 FOR ADDITIONAL

SYSTEMS LIKE MED GAS, VACUUM SYSTEM, ETC. REFER TO

TYPICAL OUTLET CONFIGURATION FOR OUTLET SHOWN IN

THIS DETAIL.

U.S. Department of Veterans Affairs strollo & strollo 718 Virginia Drive

Orlando, FL. 32803 T: (407) 423-5355 F: (407) 422-5994

MES Group, Inc.

550 North Reo Street, Suite 203 Tampa, FL, 33609 813.289.4700 mes group

COA # 8304

ELECTRICAL AUXILIARY

SYSTEMS

EY100

GENERAL NOTES

A. CONTRACTOR SHALL COORDINATE ANY WALL MOUNTED ITEM (CARD

READERS, PUSHPLATES, NURSE CALL SYSTEM) WITH ARCHITECT AND VA

PRIOR TO INSTALLATION.

B. CONTRACTOR SHALL BE RESPONSIBLE FOR IDENTIFICATION OF ALL

RATED WALLS, CEILINGS, AND SLAB AND THEIR SPECIFIED RATING ON

THE ARCHITECTURAL DRAWINGS. ALL DEVICES AND MATERIAL SHALL

MEET THE UL RATING OF THE RATED WALL ASSEMBLY. CONTRACTOR

SHALL PROVIDE AN ASSEMBLY INSTALLED IN ACCORDANCE WITH UL FOR

THE RATED APPLICATION.

C. EXISTING CONDITIONS ARE BASED ON RECORD DOCUMENTS AND FIELD

OBSERVATION. ELECTRICAL CONTRACTOR SHALL REPORT

DISCREPANCIES TO ENGINEER PRIOR TO DISTURBING EXISTING

INSTALLATION.

D. PROVIDE JUNCTION BOXES, WIRE, CABLING, CONDUIT, ETC, AS

REQUIRED TO MAINTAIN CONTINUITY TO EXISTING TO REMAIN DEVICES,

FIXTURES, EQUIPMENT, ETC.

E. ALL UNUSED OR ABANDONED WIRE, CONDUIT, CABLING, ETC. SHALL BE

REMOVED BACK TO POINT OF ORIGIN.

F. THE GC IS RESPONSIBLE FOR PROVIDING ALL CONDUITS, J-BOXES AND

PULL STRINGS FOR THE DOOR ACCESS EQUIPMENT.

G. THE GC IS RESPONSIBLE FOR PROVIDING NECESSARY POWER OUTLETS

FOR THE DOOR ACCESS EQUIPMENT.

H. COORDINATE ALL DOOR HARDWARE AND SEQUENCE OF OPERATION

WITH ARCHITECTURAL DOOR HARDWARE SPECIFICATIONS.

I. MAGNETIC LOCKS SHALL BE CONNECTED TO THE FIRE ALARM SYSTEM

THROUGH A SET OF NORMALLY CLOSED, DRY CONTACTS SUPPLIED BY

FIRE ALARM CONTRACTOR.

J. DOOR HARDWARE SHALL BE COORDINATED WITH FIRE ALARM SYSTEM

TO DISENGAGE UPON FIRE ALARM SYSTEM ACTIVATION. COORDINATE

FINAL LOCATION OF CONDUIT AND JUNCTION BOXES WITH SUCCESSFUL

DOOR SECURITY HARDWARE PROVIDER PRIOR TO CONSTRUCTION.

K. PANIC DURESS CONTROL PANEL TO BE CONNECTED TO VA POLICE

SYSTEM. SHOULD PANIC DURESS BUTTON BE ACTUATED, ALARM SIGNAL

SHALL BE SENT TO VA POLICE DEPARTMENT.

KEYNOTES

1. PROVIDE RELAY CONNECTED TO FIRE ALARM SYSTEM. COORDINATE THE

REQUIREMENTS WITH THE DOOR HARDWARE, SECURITY AND FIRE

ALARM SYSTEM VENDORS.

2. EXISTING CARD READER TO REMAIN. CONTRACTOR TO BE RESPONSIBLE

FOR ALL CONNECTIONS AND FUNCTION OF DOOR SYSTEM.

3. COORDINATE WITH VA FOR PROVISIONS TO BE PROVIDED UNDER THIS

CONTRACT. AT MINIMUM GENERAL CONTRACTOR SHALL INCLUDE IN BID

CONDUITS, JUNCTION BOXES AND PULL STRINGS TO DEVICES

LOCATIONS SHOWN. JUNCTION BOXES SHALL BE PROVIDED WITH SOLID

COVER.

NOTE: REFER TO SPECIFICATION 10 25 13 FOR ADDITIONAL

A-106

CONTROL

A-105

ROOM

HOUSE-

KEEPINGKEEPING

HOUSE-

A-112A-112 A-111A-111

A-104

299.00n.s.f.

C O

R R

I D

R R

I D

O R

C

-1

R/F ROOM

MULTIPURPOSE

CLOSET

EQUIP.

ASSISTANT

BATHROOM

A-116p

AUTOMATION

OFFICE

A-116q

F.H.

LOUNGE/

LOCKER

ROOM

I.R.

OFFICE

PREP/RECOVERY

PREP/RECOVERY

PREP/RECOVERY

READING

AREA

PREP/RECOVERY

SOILED

LINEN

CATHETERS

SUPPLY

PREP/RECOVERY

SCRUB AREA

NURSE

STATION

LINEN

STORAGE

RECLINERS /

OUTPROCESSING100

ENTRY

C-RENO

D H

D H

S

S

S

S

S

S

CLG

CLG

S

CLG

CLG

S

S

CLG

S

U.S. Department of Veterans Affairs strollo & strollo 718 Virginia Drive

Orlando, FL. 32803 T: (407) 423-5355 F: (407) 422-5994

MES Group, Inc.

550 North Reo Street, Suite 203 Tampa, FL, 33609 813.289.4700 mes group

COA # 8304

FIRE ALARM PLAN

FA100

GENERAL NOTES

A. EXISTING CONDITIONS BASED ON FIELD OBSERVATION. ELECTRICAL

CONTRACTOR SHALL FIELD VERIFY EXISTING CONDITIONS AND REPORT

DISCREPANCIES TO VA/COR PRIOR TO DISTURBING EXISTING

INSTALLATIONS.

B. CONTRACTOR SHALL BE RESPONSIBLE FOR ALL FIRE ALARM DEVICES,

WIRING, UNLESS OTHERWISE NOTED.

C. FIRE ALARM DEVICES SHALL BE COMPATIBLE WITH EXISTING

HONEYWELL NOTIFIER FIRE ALARM SYSTEM IN HOSPITAL.

D. ELECTRICAL CONTRACTOR SHALL COORDINATE WITH OTHER TRADES AS

REQUIRED TO KEEP THE PROJECT PROGRESSING.

E. MAINTAIN AND RESTORE, IF INTERRUPTED, ALL CONDUITS AND

CONDUCTORS PASSING THROUGH AREAS AND SERVICING UNDISTURBED

AREAS.

F. ENSURE ALL FIRE ALARM CONDUIT, JUNCTION BOXES, ETC. ARE PAINTED

RED. ALL CONDUIT IS TO BE LABELED EVERY 10 FEET POINTING

TOWARDS THE FACP. ALL JUNCTION BOXES ARE TO BE LABELED TO

THEIR CONTENTS (SLC OR NAC, ETC.).

KEYNOTES

1. THE EXISTING FIRE ALARM SYSTEM SHALL BE MAINTAINED ON ACTIVE -

STATUS DURING CONSTRUCTION PERIOD.

strollo & strollo 718 Virginia Drive

Orlando, FL. 32803 T: (407) 423-5355 F: (407) 422-5994

MES Group, Inc.

550 North Reo Street, Suite 203 Tampa, FL, 33609 813.289.4700 mes group

COA # 8304

ELECTRICAL ONE-LINE

DIAGRAM

E-500

0A

T

0A

T

0A

T

0A

T

0A

T

0A

T

0A

T

0A

T

0A

T

0A

T

0A

T

0A

T

0A

T

0A

T

0A

T

PANEL

EXISTING

1HA (1)

800A 480V

XFMR 1LA

480V PRIM

208V SEC

75 KVA

RM: A179i-X

PANEL

NEW

1LA

225A 208V

SWITCHBOARD SB1-L

480V, 4000A

ROOM: BASEMENT

0A

T

0A

T

0A

T

0A

T

0A

T

0A

T

0A

T

0A

T

0A

T

0A

T

0A

T

0A

T

0A

T

SWITCHBOARD SB1-R

480V, 4000A

ROOM: BASEMENT

AT

AT

AT

AT

XF-T1

1500 KVA

4160V PRIM

480V SEC

XF-T4

1500 KVA

4160V PRIM

480V SEC

XF-T2

1500 KVA

4160V PRIM

480V SEC

1HA (1)

400AF

350AT

480V

RM: ELEV 80

1HA (2)

400AF

350AT

480V

RM: ELEV 80

RM: A179i-X

G

GEN 2

480V 750 kW RM: C39a

0A

T

AT

0A

T

EMERGENCY

SWITCHBOARD

480V, 2000A ROOM: C39a

PANEL

RM: C-39

800A

BKR

100A

BKR

E N

ATS-11 (N)

480V, 800A

RM: BASEMENT

0A

T

0A

T

0A

T

SB2 A

800AT

GEN 2

2000AT

0A

T

0A

T

SWITCHBOARD SB2-A

480V, 1600A

ROOM: BASEMENT

PANEL

EXISTING

EXH

400A 480V

RM: 340-XXFMR EXL

480V PRIM

208V SEC

45 KVA

RM: 340-X

PANEL

EXISTING

EXL

150A 208V

RM: 340-X

70A

BKR

GENERAL NOTES

A. EXISTING CONDITIONS ARE BASED ON RECORD DOCUMENTS AND FIELD

OBSERVATION. NOTIFY ENGINEER OF ANY DISCREPANCIES BETWEEN

THESE DRAWINGS AND EXISTING CONDITIONS PRIOR TO DISTURBING

EXISTING INSTALLATION.

B. ALL SERVICE INTERRUPTIONS TO THIS EXISTING FACILITY MUST BE

SCHEDULED AT LEAST 3 WEEKS IN ADVANCE AND BE KEPT TO A

MINIMUM. COORDINATE ALL DISRUPTIVE WORK AND OUTAGE

REQUIREMENTS WITH THE VA/COR.

C. REMOVE EXISTING ELECTRICAL DEVICES, EQUIPMENT, BRANCH

CIRCUITS AND FEEDERS THAT ARE INDICATED FOR DEMOLITION IN THEIR

ENTIRETY BACK TO POINT OF ORIGIN UNLESS OTHERWISE INDICATED.

TURN OFF AND LABEL CIRCUIT BREAKERS AS SPARES FOR NEW WORK

WHERE APPLICABLE.

D. FOR EQUIPMENT WITHIN THE SCOPE OF THIS REMODEL, VERIFY

CONDITION AND AGE OF EXISTING REUSED ELECTRICAL EQUIPMENT,

CIRCUIT BREAKERS, FUSES, CONDUIT, SWITCHES AND RELATED WIRING.

NOTIFY ENGINEER OF ANY ELECTRICAL AND WIRING AGED BEYOND ITS

USEFUL LIFE AND REPLACE AS DIRECTED.

E. ELECTRICAL DRAWINGS ARE DIAGRAMMATIC/SCHEMATIC IN NATURE AND

REPRESENT THE GENERAL SCOPE OF WORK. IT IS NOT WITHIN THE

SCOPE OF THE ELECTRICAL DRAWINGS TO SHOW ALL NECESSARY

RACEWAY ROUTING, BENDS, OFFSETS, PULL BOXES AND

OBSTRUCTIONS. CONTRACTOR SHALL COORDINATE THE FINAL

LOCATION OF EQUIPMENT FOR PROPER OPERATION IN ACCORDANCE

WITH CODE, VA AND MANUFACTURER RECOMMENDATIONS.

F. ELECTRICAL CONTRACTOR SHALL REVIEW OTHER DISCIPLINES

DRAWINGS AND SHALL DISCONNECT AND MAKE SAFE FOR REMOVAL OF

ALL EQUIPMENT SHOWN TO BE DEMOLISHED.

G. ALL DEMOLISHED EQUIPMENT SHALL BE PRESENTED TO VA FOR

FIRST RIGHT OF REFUSAL

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

XF-T3

1500 KVA

4160V PRIM

480V SEC

TO SG2

1200A, 4161V

RM: 1ST FL

TO SG2

1200A, 4161V

RM: 1ST FL

TO SG1

1200A, 4161V

RM: 1ST FL

TO SG1

1200A, 4161V

RM: 1ST FL

KEYNOTES

1. ELECTRICAL CIRCUITS CURRENTLY FEEDING THE LIGHTING IN THE

SCOPE OF WORK, SHALL BE DISCONNECTED FROM PANEL '1HA(1) AND

RETAINED FOR RECONNECTION OF NEW LIGHTING FIXTURES IN THE

SPACE.

2. CONNECT NEW EMERGENCY FIXTURES TO 20AMP BREAKER IN PANEL

'1CP' LOCATED IN ELECTRICAL ROOM A-179b. ELECTRICAL PANEL '1CP'

SHALL BE REPLACED TO COMPLY WITH CURRENT CONSTRUCTION AND

ELECTRICAL CODES.

3. EXISTING CIRCUITS CONNECTED TO ELECTRICAL PANELS '1LA', '1LX'

AND 'ULTRASOUND' WILL BE REUSED AS REQUIRED. NEW WIRES,

BREAKERS AND CONDUIT SHALL BE PROVIDED AND ELECTRICAL

PANELS '1LA' AND '1LX' SHALL BE REPLACED TO COMPLY WITH

CURRENT CONSTRUCTION AND ELECTRICAL CODES.

4. REFER TO POWER FLOOR PLAN KEY NOTES FOR ADDITIONAL DETAILS.

PANEL

PANEL

NEW

1LX

225A 208V

TO EXIST.

LOAD

1LX DISC

225A 480V RM: A179i-X

XFMR 1LX

480V PRIM

208V SEC

75 KVA

RM: A179i-X

PANEL

EXISTING

BLX

100A 208V

RM: A78-X

TO EXIST.

LOAD

EXISTING

225A 208V

ULTRA-

SOUND

TO EXIST.

LOAD

TO EXIST.

LOAD

EXISTING

OPA EMER

1200A 480V

800A

BKR

E N

ATS-10 (N)

480V, 800A

RM: BASEMENT

0A

T

0A

T

0A

T

SB2 B

800AT

0A

T

0A

T

SWITCHBOARD SB2-B

480V, 1600A

ROOM: BASEMENT

TO EXIST.

LOAD

TO EXIST.

LOAD

TO EXIST.

LOAD

0A

T

TO EXIST.

LOAD

0A

T

TO EXIST.

LOAD

0A

T

TO EXIST.

LOAD

0A

T

TO EXIST.

LOAD

TO EXIST.

LOAD

SB2 B

800AT

PANEL

EXISTING

BCP

250A 208V

RM: A78-X

XFMR 1CP 480V

PRIM

208V SEC

75 KVA

RM: A179i-X

PANEL

NEW

1CP

200A 208V

RM: A179i-X

RM: A179i-X

90A

BKR

RM: ADJACENT

ULTRASOUND

ROOM

RM: A179i-X

FOR PROJECTS WITH GENERATORS FOR LIFE SAFETY WHERE PANEL BOARDS ARE

REPLACES OR ADDED, OR WHERE FUSED DISCONNECTS AND/OR ENCLOSED

CIRCUIT BREAKERS ARE ADDED OR REPLACED, THE MANUFACTURER SHALL

PERFORM SELECTIVE COORDINATION STUDY AND ARCH FLASH STUDY FOR NEW

PANEL BOARDS AND/OR CIRCUIT BREAKERS. PROVIDE NEW DEVICES WITH

ADJUSTABLE TRIP MECHANISMS AS REQUIRED TO ACHIEVE COORDINATION. ALL

ADJUSTABLE TRIP DEVICES SHALL BE FACTORY SET TO ACHIEVE COORDINATION.

ALL ADJUSTABLE TRIP DEVICES SHALL BE FACTORY SET TO ACHIEVE

COORDINATION. REFER TO ARCH FLASH LABELING DETAILS FOR LABELING

REFERENCE.

AC (ACCESS CONTROL)

DPS (DOOR POSITION SWITCH)

EL/REX (ELECTRIC LOCK / REQUEST TO EXIT)

TO FIRE ALARM

RELAY MODULE

MANUFACTURER'S ACCESS

CONTROL CABLE (TYPICAL)

* RETAIN THE SERVICES OF A SYSTEM AUTHORIZED SERVICE TECHNICIAN FOR THE EXISTING ACCESS

CONTROL SYSTEM TO SUPERVISE TERMINATION TO THE CONTROL PANEL AND TO MAKE SYSTEM

PROGRAMMING AND GRAPHICS MODIFICATIONS IN ACCORDANCE WITH EXISTING SYSTEM WARRANTY AND

MANUFACTURER'S RECOMMENDATIONS.

*COORDINATE WITH GC AND DOOR HARDWARE MANUFACTURER FOR ELECTRIC STRIKES, MAGNETIC

LOCKS AND DOOR OPERATORS FOR CONNECTION OF ACCESS CONTROLS AND PUSH BUTTONS TO

RELEASE DOOR LOCKS BEFORE OPERATORS OPENS DOOR.

TWO HOLE STRAP OR

CADWELD CONNECTION TYPE

''LK'', TYPICAL

MOUNTING BRACKETS

FIBERGLASS INSULATORS

4"

MIN.

1.

2.

3.

4.

NOTES:

PREDRILLED BOLT HOLE SIZE AND SPACING AS REQUIRED FOR INDICATED

TERMINATIONS.

PROVIDE LENGTH SUFFICIENT FOR ALL INDICATED TERMINATIONS AND 20% SPARE

MOUNTING SPACE. CONNECTIONS SHALL UTILIZE TWO HOLE COMPRESSIONS

CONNECTOR.

GROUND BAR SHALL BE MOUNTED MINIMUM 2" OFF WALL AND 12" AFF.

FIBERGLASS INSULATORS SHALL HAVE A MINIMUM DIELECTRIC STRENGTH OF 15kV.

INSULATED COPPER GROUND

CONDUCTOR TO BUILDING GROUNDING

ELECTRODE CONDUCTOR

NOTES:

1. TYPICAL FOR WOOD AND METAL STUD ROUGH-IN.

2. PLASTER RINGS NOT SHOW.

3. LOCATE ALL OUTLET BOXES IN ACCORDANCE WITH ARCHITECTURAL AND MECHANICAL

DRAWINGS, AND WITH ALL APPLICABLE SHOP DRAWINGS.

4. IN ACCORDANCE WITH UBC 4304 OUTLETS ON OPPOSITE SIDES OF WALLS OR PARTITIONS IN

THE SAME STUD SPACE MUST BE SEPARATED BY A MIN. OF 24" HORIZONTAL DISTANCE.

5. TOENAILING OF OUTLET BOXES DIRECTLY TO THE STUDS WILL NOT BE ACCEPTED.

6. OUTLETS SHOWN TOGETHER ON PLAN SHALL BE INSTALLED TOGETHER.

TYPICAL

OUTLET BOX

BOX SUPPORT

AS REQUIRED FOR TYPE

OF CONTRUCTION

PROVIDE CONDUIT SUPPORTS IN

ACCORDANCE WITH NEC. SPACING

REQUIREMENTS FOR TYPE OF RACEWAY

REQUIRED.TYPICAL

WALL

OUTLETS

S S

EXISTING

PA

SYSTEM

CABINET

(ETR)

ADD PA SPEAKERS ONTO EXISTING

EQUIPMENT. EXTEND EXISTING WIRING

AS REQUIRED FROM CENTRAL SYSTEM.

ADD ADDITIONAL EQUIPMENT AS

REQUIRED PER SPECS.

CARD

READER

OR

KEYPAD

ELECTRIC

POWER HINGE

BY DOOR

HARDWARE

VENDOR

CARD READER OR

KEYPAD BY DIVISION

28; IF REQUIRED,

1-4"x4" BACKBOX WITH

SINGLE GANG

PLASTER RING, BY

DIVISION 26

PANIC BARPANIC BAR

MAG LOCK BY DOOR

HARDWARE VENDOR

CABLING BY DIVISION

ELECTRIC POWER DOOR

OPENER BY DOOR

HARDWARE VENDOR

DOOR CONTACT BY

DOOR HARDWARE

VENDOR, CABLING BY

DIVISION 26

DOOR RELEASE BUTTON AND

CABLING IN ANY LOCATION BY

DIVISION 28 CONTRACTOR; IF

REQUIRED, 1-4"x4" BACKBOX

WITH

SINGLE GANG PLASTER RING, BY

DIVISION 26

PUSH TO EXIT BUTTON AND

CABLING WITHIN 5'-0" OF

DOOR BY DIVISION 28

CONTRACTOR; IF REQUIRED,

1-4"x4" BACKBOX WITH

SINGLE GANG PLASTER

RING, BY DIVISION 26

CONDUIT BY

DIVISION 26

CONDUIT BY DIVISION

26 AND CABLING BY

DIVISION 28

BY DIVISION 26 CONTRACTOR

REQUEST TO EXIT IS A PART OF THE ELECTRIC

LOCK OR HINGE MOTION SENSOR BY DOOR

HARDWARE VENDOR. CABLING BY DIVISION 28

CONTACTOR; IF REQUIRED, 1-4"x4" BACKBOX

WITH SINGLE GANG PLASTER RING, BY

DIVISION 26

ABOVE ACCESSIBLE CEILING

CABLE TO SECURITY PANEL BY DIVISION 28 CONTRACTOR; POWER

BY

DIVISION 26 TO BE AT SECURITY PANEL. COORDINATE POWER

REQUIREMENTS WITH DIVISION 28 CONTACTOR.

1" CONDUIT BY

DIVISION 26;

CABLING BY

DIVISION 28

NOTE:

THIS IS A EXAMPLE DOOR SHOWING ALL

TYPICAL / POSSIBLE CONTROL DETAILS.

TYPICAL DOOR ACCESS. DEVICES INDICATED

ON THIS DETAIL MAY NOT BE UTILIZED

IN THE PROJECT. THE CONTRACTOR

SHALL COORDINATE WITH THE

ARCHITECT, DOOR HARDWARE SUPPLIER

AND SHOP DRAWINGS FOR ITEMS TO BE

PROVIDED BY DOOR HARDWARE

VENDOR TO PROVIDE A COMPLETE AND

FUNCTIONAL DOOR ACCESS CONTROL

SYSTEM FOR EACH INDIVIDUAL DOOR

CONDITIONS.

MD

DC DC

MAG MAG

EPOEPO

P

EH EH

JUNCTION BOX

U.S. Department of Veterans Affairs strollo & strollo 718 Virginia Drive

Orlando, FL. 32803 T: (407) 423-5355 F: (407) 422-5994

MES Group, Inc.

550 North Reo Street, Suite 203 Tampa, FL, 33609 813.289.4700 mes group

COA # 8304

ELECTRICAL DETAILS

E-600

GROUNDING DETAIL KEYNOTES

1. GROUND BUS BAR LOCATED IN MAIN ELECTRICAL ROOM OR WITHIN

SERVICE ENTRANCE MAIN. 1/4" x 1" MINIMUM FOR EXTERNAL

INSTALLATION.

2. GROUNDING TRIAD, 3-3/4" X 10'-0" COPPERCLAD GROUND RODS DRIVEN

INTO GROUND AT LEAST 1 ROD'S LENGTH APART. PROVIDE WITH

INSPECTION TEST WELL.

3. COPPER GROUNDING ELECTRODE CONDUCTOR SIZED PER NEC TABLE

250.66, MINIMUM SIZE #8.

4. SERVICE ENTRANCE MAIN BONDING JUMPER SIZED PER NEC TABLE

250.102(C)(1). NEUTRAL SHALL ONLY BE BONDED AT SERVICE ENTRANCE,

ALL OTHER NEUTRALS SHALL BE CONSIDERED FLOATING.

5. CONNECTIONS TO BUILDING STEEL SHALL BE BY EXOTHERMIC WELD.

6. CONNECTIONS TO REBAR ENCASED IN CONCRETE SHALL BE BY

EXOTHERMIC WELD.

7. BOND METALLIC COLD WATER PIPE WITHIN 5' - 0" OF ENTERING BUILDING.

CONNECTION SHALL BE MADE WITH NON-CORROSIVE MATERIAL

GROUNDING ELECTRODE CLAMP.

8. SERVICE ENTRANCE NEUTRAL CONDUCTOR.

9. ALL EQUIPMENT ENCLOSURES AND METAL RACEWAYS SHALL BE

GROUNDED WITH AN EQUIPMENT GROUNDING CONDUCTOR SIZED PER

NEC TABLE 250.122.

10. EQUIPMENT GROUNDING CONDUCTOR SIZED PER NEC TABLE 250.122.

11. NEUTRAL CONDUCTOR WITH INSULATED EQUIPMENT GROUNDING

CONDUCTOR TO BRANCH CIRCUIT PANELS/EQUIPMENT.

X

GROUND

BAR

NEUTRAL

BAR

CATV FA SEC ELEC

METER

GROUND

BAR

NEUTRAL

BAR

TO UPPER FLOORS, REMOTE

ELECTRICAL ROOMS, IT CLOSETS

WHERE APPLICABLE

TO LIGHTNING PROTECTION

SYSTEM, WHERE APPLICABLE

TO REMOTE BUILDINGS

WHERE APPLICABLE

GRADE

3 3 3

SERVICE ENTRANCE MAIN BRANCH CIRCUIT PANEL

HEM

120/208V, 3PH, 4W

FED FROM MSB BKR. 11

SCA 36,921A 01/03/12

LETTER (FILL) COLOR

EMERGENCY - WHITE

NORMAL - WHITE

INDICATED

VOLTAGE,

NO. OF PHASES,

NO OF WIRES

INDICATES WHERE

THIS EQUIPMENT IS

FED FROM (TRANSFER

SWITCHES WILL HAVE

TWO LINES.)

CALCULATED

AVAILABLE FAULT

CURRENT

ATTACH

NAMEPLATE

WITH 2 SCREWS

NAMEPLATE COLOR

LIFE SAFETY - YELLOW

CRITICAL - ORANGE

EQUIPMENT - GREEN

NORMAL - BLACK

EMERGENCY - RED

LETTERING

SHALL BE

1/4" HIGH

ELECTRICAL EQUIPMENT NAMEPLATE NTS-

TYPICAL WALL

OUTLETS

PROVIDE CONDUIT SUPPORTS IN

ACCORDANCE WITH NEC. SPACING

REQUIREMENTS FOR TYPE OF RACEWAY

REQUIRED.

AS REQUIRED FOR TYPE

OF CONSTRUCTION.

BOX

SUPPORT

TYPICAL

OUTLET

BOX

NOTES:

1. TYPICAL FOR WOOD AND METAL STUD ROUGH-IN.

2. PLASTER RINGS NOT SHOWN.

3. LOCATE ALL OUTLET BOXES IN ACCORDANCE WITH ARCHITECTURAL AND

MECHANICAL DRAWINGS, AND WITH ALL APPLICABLE SHOP DRAWINGS.

4. IN ACCORDANCE WITH UBC 4304 OUTLETS ON OPPOSITE SIDES OF WALLS

OR PARTITIONS IN THE SAME STUD SPACE MUST BE SEPARATED BY A MIN. OF 24"

HORIZONTAL DISTANCE.

5. TOENAILING OF OUTLET BOXES DIRECTLY TO THE STUDS WILL NOT BE

ACCEPTED.

6. OUTLETS SHOWN TOGETHER ON PLAN SHALL BE INSTALLED TOGETHER.

OF AUDIBLE/VISUAL ALARM DEVICE

FINISHED FLOOR

TYPICAL ELEVATION DETAIL TYPICAL ELEVATION DETAIL

OF VISUAL ALARM DEVICE

TYPICAL ELEVATION DETAIL

OF MANUAL PULL STATION

VISUAL DEVICE ONLY

FIRE ALARMFIRE ALARM

AUDIBLE/VISUAL DEVICEAUDIBLE/VISUAL DEVICE

MUST BE IN CONDUIT

UP TO 7'-0" AFF

TO BOTTOM

80" AFF

OF STROBE

TO BOTTOM

80" AFF

OF STROBE

TO TOP OF

48" AFF

ACTIVATION

MANUAL STATION

FINISHED FLOOR FINISHED FLOOR

AUDIBLE DEVICE ONLY

FIRE ALARM

TO TOP

90" AFF

OF DEVICE

FINISHED FLOOR

TYPICAL ELEVATION DETAIL

OF AUDIBLE DEVICE

"W"

"B" "E"

3/8" DIAMETER BOLT

HOLES SECURE TO

HORIZONTAL C6x12GA

WITH 3/8" DIAMETER

MACHINE SCREWS

DEEP LEG TRACK

FRONT VIEW

SIDE VIEW

1 1/2" CRCx16GAx4"-4" "A"

"B"

"C"

"D"

.177x1 7/16" PENETRATION AT 8" ON

CENTER. TYPICAL FOR TOP AND BOTTOM

POWER DRIVEN FASTENER AT PANEL

ONLY.

2-#8-18 EACH FACE

1 1/2" CRCx16GAx4"x4"

TYPICAL

EACH

FLANGE

TYPICAL

1/8"

1/8"

1/8"

C6x12GA CONT. OVER FOUR

STUDS (COPE REQUIRED)

FIELD WELD TO VERTICAL

STUDS AS SHOWN

NOTES: DO NOT PENETRATE 1 1/2" CRC WITH SCREWS.

120# [35 8"x16 GA. AT

16" O.N.

#1

4-5/16" DIA. MACHINE

SCREWS

MAX.

UNIT

WEIGHT

PANEL

TYPE

#2

#3

#4

300#

600#

1200#

"A" "B" "C" "D" "E"

16"

22"

28"

38"

"W"

20" 52" 53 4"

4-5/16" DIA. MACHINE

SCREWS

4-5/16" DIA. MACHINE

SCREWS

4-5/16" DIA. MACHINE

SCREWS

26" 42" 61 2"

32" 40" 81 4"

44" 28" 91 2"

[35 8"x16 GA. AT

16" O.N.

[35 8"x16 GA. AT

16" O.N.

[35 8"x16 GA. AT

16" O.N.

CONTROL OUTPUT

COMMON

+24VDC

R

ED

BL

K

BL

U

A D

O L

AUXILIARY

RELAY PACK

NEUTRAL

HOT BLK

NEUTRAL WHT

HOT BLK

RED

RED

POWER

PACK

LOCAL OVERRIDE ROCK

SWITCH OR DIMMER

SWITCH AS REQUIRED

TWO CIRCUIT OR TWO

LOAD SENSOR CONTROL

A D

O L

RED

RED

ANY

24VDC

CEILING/WALL

SENSOR

TO

ADDITIONAL

SENSORS

TO

ADDITIONAL

RELAY PACKS

120V BRANCH

CIRCUIT

120V BRANCH

CIRCUIT

LOCAL OVERRIDE ROCK

SWITCH OR DIMMER

SWITCH AS REQUIRED

LUMINAIRE MANUFACTURER'S

MOUNTING HARDWARE REFER TO

SPECIFICATION SECTION 26 51 00

LUMINAIRE

SUSPENSION

WIRES REFER

TO

SPECIFICATION

SECTION 26 51

00 (TYP)

ARCHITECTURAL

CEILING GRID

ACOUSTICAL CEILING TLE

(TYP)

LUMINARIE

REFER TO

SCHEDULE

ACOUSTICAL CEILING

TLE (TYP)

FIXTURE WHIP FROM

JUNCTION BOX

(189mm (6') LONG MAX.)

3 TWIST MINIMUM

(TYP)

LUMINARIE

REFER TO

SCHEDULE

GENERAL NOTE:

1. INSTALL IN ACCORDANCE WITH MANUFACTURER'S MOUNTING INSTRUCTIONS AND USING THE RECOMMENDED MOUNTING

HARDWARE.(TYP).

2. GENERAL CONTRACTOR SHALL PROVIDE ALL REQUIRED FASTENERS, HANGERS, STRUTS AND HARDWARE TO PROVIDE A

FULLY SEISMIC RATED SUPPORT SYSTEM FOR THE LIGHT FIXTURES.

strollo & strollo 718 Virginia Drive

Orlando, FL. 32803 T: (407) 423-5355 F: (407) 422-5994

MES Group, Inc.

550 North Reo Street, Suite 203 Tampa, FL, 33609 813.289.4700 mes group

COA # 8304

ELECTRICAL SCHEDULES

E-700

EXISTING PANEL: 1HA(1) PANELBOARD SCHEDULE

Description Circuit Breakers Wire and

Conduit Load (VA)

Ph as e Load (VA) Wire and Conduit

Circuit Breakers Description # Trip (A) Poles Options A B C A B C Options Poles Trip (A) #

1 LGT - NURSE STATION 20 1 C2-20 1,200 A - 3 20 2

3 RCPT - PREP RECOV. 104 20 1 C2-20 1,440 B - - 4

5 RCPT - PREP RECOV. 105 20 1 C2-20 1,440 C - - 6

7 RCPT - PREP RECOV. 107 20 1 C2-20 1,440 A - 3 400 8

9 RCPT - NURSE STAT. 101 20 1 C2-20 1,260 B - - 10

11 RCPT - NURSE STAT. 101 20 1 C2-20 1,080 C - - 12

13 RCPT - PREP RECOV. 112 20 1 C2-20 1,440 A 1,080 C2-20 1 20 RCPT - READING AREA 110 14 15 RCPT - PREP RECOV. 111 20 1 C2-20 1,440 B 200 C2-20 1 20 RCPT - NURSE STAT. DED. 16 17 RCPT - NURSE STAT. 20 1 C2-20 1,440 C 200 C2-20 1 20 RCPT - NURSER STAT. DED 18 19 RCP T- PREP/RECOV/REC. 106 20 1 C2-20 900 A 1,440 C2-20 1 20 RCPT - REC OUT 106 20 21 20 1 - B - 3 30 22

23 ROOM A103B A/C UNIT 20 1 - C - - 24

25 RCPT - SOILED LINEN 20 1 C2-20 180 A - - 26

27 RCP T- LINEN STORAGE 20 1 C2-20 180 B - 1 20 SPARE 28

29 SPACE 1 - C - 3 100 30

31 SPACE - A - - 32

33 SPACE - B - - 34

35 - C - 3 225 36 37 - A - - 38 39 - B - - 40

41 - C - SPACE 42

43 - A - SPACE 44

45 - B - SPACE 46

Connected Demand Demand Connected Load (VA) Panel Options Circuit Breaker Options Load Description Load (VA) Factor Load (VA) Phase A: 7,680 Voltage: 480Y/277V, 3�, 4W AFCI Arc Fault Circuit Interrupter Lighting: 1,200 1.25 1,500 Phase B: 4,520 Mains: 800A MLO GFCI GFCI-Personnel (4-6 mA) Receptacles - First 10 kVA: 10,000 1.00 10,000 Phase C: 4,160 Rating: 10 kAIC GFP Ground Fault Protection Receptacles - Over 10 kVA: 5,160 0.50 2,580 Total (VA): 16,360 Minimum Bus Rating: 800A RB Red Breaker Motors: - 1.00 - Mounting: Surface ST Shunt Trip Largest Motor: - 0.25 - See Wire and Conduit

Schedule for wire and conduit sizes.

Enclosure Type: NEMA 1 L-ON CB Lock in Closed Position Air Conditioning: - - - Isolated Ground: No L-OFF CB Lock in Open Position Heat Pumps & Non-Coincidental: - 1.00 - Sub-feed Lugs: No TC/TC Timeclock On/Timeclock Off Electric Space Heating: - 1.00 - Feed-thru Lugs: No PC/TC Photocell On/Timeclock Off Kitchen: - 1.00 - PC/PC Photocell On/Photocell Off Elevators: - 1.00 - Notes:

Continuous Loads: - 1.25 - 1.

Non-continuous Loads: - 1.00 - 2.

Totals (VA): 16,360 14,080 3.

Total (A): 17 4.

NEW PANEL: 1LA PANELBOARD SCHEDULE

Description Circuit Breakers Wire and

Conduit Load (VA)

Ph as e Load (VA) Wire and Conduit

Circuit Breakers Description # Trip (A) Poles Options A B C A B C Options Poles Trip (A) #

1 LTS A112,A,B,A112C,A102… 20 1 - A - 1 20 RCPT A178,A177,A175,A174,A173,C1-62

3 RCPT A150,A151,A113,A155,A152 20 1 - B - 1 20 RCPT A178,A177,A176,A175,A174,A1734 5 RCPT A150,A151,A153,A155,A152 20 1 - C - 1 20 RCPT A178,A177,A176,A175,A174,A1736

7 RCPT A179,A153,A155,A152 20 1 - A - 1 20 RCPT A149,A148,A179 8

9 RCPT A180,A101,A107,A116F 20 1 - B - 1 20 RCPT A149,A150,A148,A1479,SS CLS A1710

11 RCPT STAIR 1,A101,A116F 20 1 - C - 1 20 RCPT A149,A148,A179 12

13 RCPT A104,A105,A112 20 1 - A - 1 20 RCPT A102, A164 14

15 RCPT A102,A103,CR A104 20 1 - B - 1 20 RCPT A150, A140 16

17 RCPT A153, A154 20 1 - C - 1 20 RCPT A155, A156 18

19 RCPT A156, A154 20 1 - A - 1 20 RCPT A113, A131, A178, ESM 20

21 RCPT A151, EKGB151 20 1 - B - 1 20 RCPT A113A 22

23 RCPT A114, A142 20 1 - C - 1 20 ESM A105, A106, A223C 24

25 20 1 - A - 1 20 RADIOLOGY 26

27 RCPT B101 20 1 - B - 1 20 RADIOLOGY 28

29 RCPT B104(31), B101 20 1 - C - 2 30 DEVELOPER A113B 30

31 DEVELOPER A113B 20 1 - A - - 32

33 20 1 - B - 1 RCPT A179, ESM 34

35 20 1 - C - 1 36

37 20 1 - A - 3 90 PNL ULTRASOUND 38

39 20 1 - B - - - 40

41 ULTRASOUND MACH A112 BLUE 20 1 - C - - - 42

Connected Demand Demand Connected Load (VA) Panel Options Circuit Breaker Options Load Description Load (VA) Factor Load (VA) Phase A: - Voltage: 208Y/120V, 3�, 4W AFCI Arc Fault Circuit Interrupter Lighting: - 1.25 - Phase B: - Mains: 225A MCB GFCI GFCI-Personnel (4-6 mA) Receptacles - First 10 kVA: - 1.00 - Phase C: - Rating: 22 kAIC GFP Ground Fault Protection Receptacles - Over 10 kVA: - 0.50 - Total (VA): - Minimum Bus Rating: 225A RB Red Breaker Motors: - 1.00 - Mounting: Surface ST Shunt Trip Largest Motor: - 0.25 - See Wire and Conduit

Schedule for wire and conduit sizes.

Enclosure Type: NEMA 1 L-ON CB Lock in Closed Position Air Conditioning: - - - Isolated Ground: No L-OFF CB Lock in Open Position Heat Pumps & Non-Coincidental: - 1.00 - Sub-feed Lugs: No TC/TC Timeclock On/Timeclock Off Electric Space Heating: - 1.00 - Feed-thru Lugs: No PC/TC Photocell On/Timeclock Off Kitchen: - 1.00 - PC/PC Photocell On/Photocell Off Elevators: -…