SurCoPrimer Data Sheets.pdf

SURCOPRIMER – FRP &SURCOPRIMER – FRP &

CORROSION INHIBITORCORROSION INHIBITOR

DESCRIPTION

SurCoPrimer- FRP & Corrosion Inhibitor is a two layer surface applied product system for use on concrete surfaces in preparation for the installation of fiber reinforced polymer (FRP) reinforcing laminates.

SurCoPrimer – FRP Layer I (SCP I) migrates from concrete surface to reinforcing steel and inhibits corrosion.

SurCoPrimer – FRP Layer II (SCP II) reacts with the concrete cement to increase dynamic tensile yield strength.

Steel Reinforced Concrete/ Fiber Reinforced Polymer (FRP)

SPECIFICATION

SCP I corrosion inhibitor performance is measured by ASTM G109 and verified by ICRI Guide 510.2-2019 and

UFGS 09 97 23.17.

SCP II tensile yield strength increase is measured by ASTM C1538 and ASTM C7522.

More details on be found on the SurCoPrimer – FRP Layer I (SCP I) and Layer II (SCP II) material specific Technical Data Sheets.

BENEFITS

Combined application of SPC I and SPC II on concrete surfaces prior to the application of FRP increased durability and life of the laminate by eliminating rebar corrosion and concrete surface strength as causes of laminate delamination.

APPLICATION PROCEDURES

Apply SCP I first and allow to dry and migrate into the concrete surface. Recommend allowing 4 to 8 hours between applications of SCP I and II. Make light application of water after application of SCP II has dried to drive all ingredient into concrete cement.

CONTACT

Surtreat Solutions 437 Grant Street, Frick Building #1210 Pittsburgh PA 15219

PHONE: 412 281 1202

FAX: 412 281 1282

www.surtreat.com info@surtreat.com

TPS and SURTREAT are trademarks of Surtreat Solutions. All rights reserved 2021.

For professional use only. Not for sale to or use by the general public.

Last Updated: 8/2021

For more information please see material specific TDS for SCP I and SCP II.

SURCOPRIMERSURCOPRIMER FRP LAYER IFRP LAYER I --

TECHNICAL DATA SHEETTECHNICAL DATA SHEET

DESCRIPTION

SurCoPrimer – FRP Layer I (SCP I) is a surface applied vapor phase migratory steel corrosion inhibitor for application on concrete members prior to application of SurCoPrimer – FRP Layer II (SCP II).

SPECIFICATION

Corrosion inhibitor performance is verified by comparative performance on corrosion active reinforced concrete using ASTM G 109 modified for surface application of inhibitor.

Average results in laboratory and measurements made on structures by a polarization resistance method method gave an 80% reduction in corrosion rate. The use of surface applied vapor phase migratory corrosion inhibitors are described in ICRI Guide 510.2-2019 section 5.4 and UFGS 09 97

23.17 “Corrosion Inhibitor Coating of Concrete Surfaces” section 2.2.1.

APPLICATION PROCEEDURE

Recommend making application of SCP I as first step in project to allow sufficient time for reaction and drying. Make one application by spray, or paint roller and brush at rate to fully wet the concrete surface. Depending on concrete porosity the resulting application rate can be between 100 200ft2/gallon. Allow to dry and then make oneapplication of water.

SCP II can be applied when the surface is completely dry.

PHYSICAL/CHEMICAL CHARACTERISTICS

Boiling point: 212F Specific gravity: 1.03 Flashpoint: > 212F pH: 8 – 8.5 Appearance and odor: amber liquid with chemical smell Shelf life: 24 months in an unsealed factory container Storage: protect from freezing

LIMITATIONS

Minimum ambient temperature and substrate temperature of 35F. Do not apply when temperature is expected to fall below freezing within twelve hours. SCP I will not penetrate sealers, coatings, paints, and membranes.

When used indoors caution should be taken to provide adequate ventilation and additional protective gear such as respirators should be worn by the applicators.

BENEFIT

Reduction in rebar corrosion rate can extend life of a structure by a factor of three times.

PACKAGING

5 gallon pail and 55 gallon drum.

Steel Reinforced Concrete/ Fiber Reinforced Polymer (FRP)

WHERE TO USE

SurCoPrimer – FRP Layer I is designed as part of an underlayment for the installation of outer reinforcement (FRP) to recondition the concrete substrate, pacify and prevent corrosion of the embedded steel.

Appropriate for use on all reinforced concrete structures where FRP repairs are being conducted. Intended for use in combination with SURTREAT SurCoPrimer – FRP Layer II.

CAUTION AND SAFETY

Handling: SURTREAT SCP I is to be applied by professional contractors only. All applicators should wear OSHA and NIOSH recommended protective equipment. Do not use or dilute the product in closed areas without adequate ventilation. Immediately close the container after removal of the solution. Avoid contact with skin, eyes and clothing. Do not smoke, eat or drink during application. Wash thoroughly after handling. Keep out of reach of children. Do not inhale or ingest or modify the solution. Refer to SDS.

CONT ON PG 2

Clean Up: In case of spills or leaks, wear suitable protective equipment. Contain spill and collect with absorbent material or process and transfer to a suitable container, ventilate area. Avoid contact. Dispose of in accordance with current, applicable local, state and federal regulations.

Precautions: KEEP OUT OF REACH OF CHILDREN. DO NOT SWALLOW. Use with adequate ventilation. Avoid mist and direct contact with eyes, skin and clothing. Wear suitable protective goggles, gloves, and clothing. In case of insufficient ventilation, wear suitable respiratory equipment. If you feel ill, seek medical advice. Wash clothing prior to re-use.

LIMITED WARRANTY NOTICE

Every reasonable effort is made to apply Surtreat® exacting standards both in the manufacture of our products and in the information that we issue concerning these products and their use. We warrant our products to be of good quality and will replace any products proved defective. Satisfactory results depend not only upon quality products, but also upon many factors beyond our control. Therefore, except for such replacement, SURTREAT® MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, INCLUDING

WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANT ABILITY,

RESPECTING ITS PRODUCTS, and SURTREAT® shall have no other liability with respect thereto. Any claim regarding product defect must be received in writing within one (1) year from the date of shipment. No claim will be considered without such written notice or after the specified time interval. User shall determine the suitability of the products for the intended use and assume all risks and liability in connection therewith. Any authorized change in the printed recommendations concerning the use of our products must bear the signature of the Surtreat® Technical Manager.

CONTACT

Surtreat Solutions 437 Grant Street, Frick Building #1210 Pittsburgh PA 15219

PHONE: 412 281 1202

FAX: 412 281 1282

www.surtreat.com info@surtreat.com

TPS and SURTREAT are trademarks of Surtreat Solutions. All rights reserved 2021.

For professional use only. Not for sale to or use by the general public.

Last Updated: 8/2021

FIRST AID

Inhalation: If breathing is difficult due to inhalation of vapor or mist, move person to fresh air and administer oxygen. If breathing has stopped give artificial respiration. Keep person warm, quiet, and get medical attention.

Eye Contact: Rinse eyes with cool water for 15 minutes. Hold eyelids open during flushing with water. Get medical attention.

Ingestion: If swallowed, immediately drink two glasses of water and induce vomiting. Get medical attention immediately. Do not give anything to an unconscious or convulsing person. For additional information on personal protective equipment, first aid, and emergency procedures, refer to the product Safety Data Sheet (SDS) on the job site or contact the company at the address or phone number given below.

Disposal of container: Triple rinse inside of container, seal opening and dispose of properly.

For medical emergencies only:

CHEMTEL 1-800-255-3924 (24 hours)

FIRST AID (CONT)

SURCOPRIMERSURCOPRIMER FRP LAYER IIFRP LAYER II --

TECHNICAL DATA SHEETTECHNICAL DATA SHEET

DESCRIPTION

SurCoPrimer–FRP Layer II (SCP II)is a surface applied concrete tensile strength builder. The average pull-off tensile yield strength is increased from 200 up to 400 psi as measured by ASTM C1538 “Standard Method For Tensile Yield Strength of Concrete Surfaces And Bond Strength or Tensile Strength of Concrete Repairs and Overlay Materials By Direct Tension Pull Off Method”

SPECIFICATION

ASTM D7522 “Standard Method for Pull-Off Strength for FRP Laminate Systems Bonded to Concrete Substrate” is used to verify that a FRP laminate bonded to concrete surface has a dynamic pull-off strength equal to or greater than 200psi. Application of SCP II to concrete surface prior to placing of FRP will guarantee that the pull-off strength from concrete surface will exceed 200psi.

APPLICATION PROCEEDURE

It is important that all product active ingredients penetrate into the concrete cement. Application rates can vary between 100 to 200ft2/gal depending on concrete cement porosity and strength. High porosity cement can take 100ft2/gallon and will be in the weakest initial condition. Make 2 applications to surface using spray, paint roller or brush depending on structure geometry. Make second application as soon as the first is free of liquid on surface.

PHYSICAL/CHEMICAL CHARACTERISTICS

Boiling point: 212F Specific gravity: 1.094 Flashpoint: none pH: 12 (+/-.5) Appearance and odor: clear liquid with mild chemical smell Shelf life: 24 months in an unsealed factory container Storage: protect from freezing

LIMITATIONS

Minimum ambient temperature and substrate temperature of 35F. Do not apply when temperature is expected to fall below freezing within twelve hours.

SCP II will not penetrate sealers, coatings, paints, and membranes.

BENEFIT

Total monolithic load resistance for a concrete member covered with FRP reinforcement can be increase by a factor of 2 when the FRP dynamic pull-off strength is increased from 200 to 400psi.

PACKAGING

5 gallon pail and 55 gallon drum.

Steel Reinforced Concrete/ Fiber Reinforced Polymer (FRP)

WHERE TO USE

SurCoPrimer – FRP Layer II is designed as part of an underlayment for the installation of outer reinforcement (FRP) to recondition the concrete substrate, increase tensile strength.

Appropriate for use on all reinforced concrete structures where FRP repairs are being conducted. Intended for use in combination with SURTREAT SurCoPrimer – FRP Layer I.

As soon as second application is dry apply a light spray of water to drive all ingredient into the cement pore structure. If rapid drying conditions exist due to temperature or wind may maybe necessary to make application of water between applications.

CONT ON PG 2

Clean Up: In case of spills or leaks, wear suitable protective equipment. Contain spill and collect with absorbent material or process and transfer to a suitable container, ventilate area. Avoid contact. Dispose of in accordance with current, applicable local, state and federal regulations.

Precautions: KEEP OUT OF REACH OF CHILDREN. DO NOT SWALLOW. Use with adequate ventilation. Avoid mist and direct contact with eyes, skin and clothing. Wear suitable protective goggles, gloves, and clothing. In case of insufficient ventilation, wear suitable respiratory equipment. If you feel ill, seek medical advice. Wash clothing prior to re-use.

LIMITED WARRANTY NOTICE

Every reasonable effort is made to apply Surtreat® exacting standards both in the manufacture of our products and in the information that we issue concerning these products and their use. We warrant our products to be of good quality and will replace any products proved defective. Satisfactory results depend not only upon quality products, but also upon many factors beyond our control. Therefore, except for such replacement, SURTREAT® MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, INCLUDING

WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANT ABILITY,

RESPECTING ITS PRODUCTS, and SURTREAT® shall have no other liability with respect thereto. Any claim regarding product defect must be received in writing within one (1) year from the date of shipment. No claim will be considered without such written notice or after the specified time interval. User shall determine the suitability of the products for the intended use and assume all risks and liability in connection therewith. Any authorized change in the printed recommendations concerning the use of our products must bear the signature of the Surtreat® Technical Manager.

CONTACT

Surtreat Solutions 437 Grant Street, Frick Building #1210 Pittsburgh PA 15219

PHONE: 412 281 1202

FAX: 412 281 1282

www.surtreat.com info@surtreat.com

TPS and SURTREAT are trademarks of Surtreat Solutions. All rights reserved 2021.

For professional use only. Not for sale to or use by the general public.

Last Updated: 8/2021

FIRST AID

Inhalation: If breathing is difficult due to inhalation of vapor or mist, move person to fresh air and administer oxygen. If breathing has stopped give artificial respiration. Keep person warm, quiet, and get medical attention.

Eye Contact: Rinse eyes with cool water for 15 minutes. Hold eyelids open during flushing with water. Get medical attention.

Ingestion: If swallowed, immediately drink two glasses of water and induce vomiting. Get medical attention immediately. Do not give anything to an unconscious or convulsing person. For additional information on personal protective equipment, first aid, and emergency procedures, refer to the product Safety Data Sheet (SDS) on the job site or contact the company at the address or phone number given below.

Disposal of container: Triple rinse inside of container, seal opening and dispose of properly.

For medical emergencies only:

CHEMTEL 1-800-255-3924 (24 hours)

FIRST AID (CONT) CAUTION AND SAFETY

Handling: SURTREAT SCP IIis to be applied by professional contractors only. All applicators should wear OSHA and NIOSH recommended protective equipment. Do not use or dilute the product in closed areas without adequate ventilation. Immediately close the container after removal of the solution. Avoid contact with skin, eyes and clothing. Do not smoke, eat or drink during application. Wash thoroughly after handling. Keep out of reach of children. Do not inhale or ingest or modify the solution. Refer to SDS.

Page 1/10 Safety Data Sheet according to 1907/2006/EC (REACH), 1272/2008/EC (CLP), and

OSHA GHS

Printing date 10.03.2015 Revision: 10.03.2015

SECTION 1: Identification of the substance/mixture and of the company/ undertaking

· 1.1 Product identifier

· Trade name: SurCoPrimer - FRP Layer I (SCP I)

· 1.2 Relevant identified uses of the substance or mixture and uses advised against No further relevant information available.

· Application of the substance / the mixture Corrosion inhibitors

· 1.3 Details of the supplier of the Safety Data Sheet

· Manufacturer/Supplier:

Surtreat Solutions, Inc.

1210 Frick Building 437 Grant Street Pittsburgh, PA 15219 Phone: 412-281-1202

· 1.4 Emergency telephone number:

ChemTel Inc.

(800)255-3924, +1 (813)248-0585

SECTION 2: Hazards identification

· 2.1 Classification of the substance or mixture

· Classification according to Regulation (EC) No 1272/2008 Classifications listed also are applicable to the OSHA GHS Hazard Communication Standard

(29CFR1910.1200).

corrosion

Eye Dam. 1 H318 Causes serious eye damage.

· Classification according to Directive 67/548/EEC or Directive 1999/45/EC

Xi; Irritant R41: Risk of serious damage to eyes.

· Information concerning particular hazards for human and environment:

The product has to be labelled due to the calculation procedure of the "General Classification guideline for preparations of the EU" in the latest valid version.

· Classification system:

The classification is according to the latest editions of the EU-lists, and extended by company and literature data.

The classification is in accordance with the latest editions of international substances lists, and is supplemented by information from technical literature and by information provided by the company.

· Additional information:

There are no other hazards not otherwise classified that have been identified.

0 percent of the mixture consists of component(s) of unknown toxicity

· 2.2 Label elements

· Labelling according to Regulation (EC) No 1272/2008 The product is additionally classified and labelled according to the Globally Harmonized System within the United States (GHS).

(Contd. on page 2)

40.1.3

Page 2/10 according to 1907/2006/EC (REACH), 1272/2008/EC (CLP), and

OSHA GHS

Printing date 10.03.2015 Revision: 10.03.2015

Trade name: SurCoPrimer - FRP Layer I (SCP I)

(Contd. of page 1) The product is classified and labelled according to the CLP regulation.

· Hazard pictograms

GHS05

· Signal word Danger

· Hazard-determining components of labelling:

alcohols, C9-11, ethoxylated

· Hazard statements H318 Causes serious eye damage.

· Precautionary statements P280 Wear protective gloves / eye protection.

P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.

P310 Immediately call a POISON CENTER/doctor.

· Hazard description:

· WHMIS-symbols:

D2B - Toxic material causing other toxic effects

· NFPA ratings (scale 0 - 4)

Health = 2 Fire = 0 Reactivity = 0

· HMIS-ratings (scale 0 - 4)

HEALTH

FIRE

REACTIVITY

Health = 2 Fire = 0 Reactivity = 0

· HMIS Long Term Health Hazard Substances None of the ingredients are listed.

· 2.3 Other hazards

· Results of PBT and vPvB assessment

· PBT: Not applicable.

· vPvB: Not applicable.

(Contd. on page 3)

Page 3/10 according to 1907/2006/EC (REACH), 1272/2008/EC (CLP), and

OSHA GHS

Printing date 10.03.2015 Revision: 10.03.2015

Trade name: SurCoPrimer - FRP Layer I (SCP I)

(Contd. of page 2)

SECTION 3: Composition/information on ingredients

· 3.2 Mixtures

· Description: Mixture of substances listed below with nonhazardous additions.

· Dangerous components:

CAS: 68439-46-3

NLP: 500-446-0

alcohols, C9-11, ethoxylated Xi R41

2,5-10%

Eye Dam. 1, H318

· Additional information:

For the listed ingredients, the identity and exact percentages are being withheld as a trade secret.

For the wording of the listed risk phrases refer to section 16.

SECTION 4: First aid measures

· 4.1 Description of first aid measures

· General information: No special measures required.

· After inhalation: Supply fresh air; consult doctor in case of complaints.

· After skin contact:

Immediately wash with water and soap and rinse thoroughly.

If skin irritation is experienced, consult a doctor.

· After eye contact:

Protect unharmed eye.

Remove contact lenses if worn.

Rinse opened eye for several minutes under running water. Then consult a doctor.

· After swallowing:

Rinse out mouth and then drink plenty of water.

Do not induce vomiting; call for medical help immediately.

· 4.2 Most important symptoms and effects, both acute and delayed Strong irritant with the danger of severe eye injury.

Slight irritant effect on skin and mucous membranes.

Gastric or intestinal disorders when ingested.

Nausea in case of ingestion.

Cramp

· Hazards Causes serious eye damage.

· 4.3 Indication of any immediate medical attention and special treatment needed No further relevant information available.

SECTION 5: Firefighting measures

· 5.1 Extinguishing media

· Suitable extinguishing agents:

CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam.

· For safety reasons unsuitable extinguishing agents: None.

· 5.2 Special hazards arising from the substance or mixture Formation of toxic gases is possible during heating or in case of fire.

(Contd. on page 4)

Page 4/10 according to 1907/2006/EC (REACH), 1272/2008/EC (CLP), and

OSHA GHS

Printing date 10.03.2015 Revision: 10.03.2015

Trade name: SurCoPrimer - FRP Layer I (SCP I)

(Contd. of page 3)

· 5.3 Advice for firefighters

· Protective equipment:

Wear self-contained respiratory protective device.

Wear fully protective suit.

· Additional information No special measures required.

SECTION 6: Accidental release measures

· 6.1 Personal precautions, protective equipment and emergency procedures Wear protective equipment. Keep unprotected persons away.

Ensure adequate ventilation For large spills, use respiratory protective device against the effects of fumes/dust/aerosol.

Particular danger of slipping on leaked/spilled product.

· 6.2 Environmental precautions: Do not allow to enter sewers/ surface or ground water.

· 6.3 Methods and material for containment and cleaning up:

Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust).

Dispose contaminated material as waste according to item 13.

Send for recovery or disposal in suitable receptacles.

· 6.4 Reference to other sections See Section 7 for information on safe handling.

See Section 8 for information on personal protection equipment.

See Section 13 for disposal information.

SECTION 7: Handling and storage

· 7.1 Precautions for safe handling Prevent formation of aerosols.

Use only in well ventilated areas.

Avoid splashes or spray in enclosed areas.

· Information about fire - and explosion protection: No special measures required.

· 7.2 Conditions for safe storage, including any incompatibilities

· Storage:

· Requirements to be met by storerooms and receptacles:

Provide ventilation for receptacles.

Avoid storage near extreme heat, ignition sources or open flame.

· Information about storage in one common storage facility:

Store away from foodstuffs.

Do not store together with oxidising and acidic materials.

· Further information about storage conditions: None.

· 7.3 Specific end use(s) No further relevant information available.

SECTION 8: Exposure controls/personal protection

· Additional information about design of technical facilities: No further data; see item 7.

(Contd. on page 5)

Page 5/10 according to 1907/2006/EC (REACH), 1272/2008/EC (CLP), and

OSHA GHS

Printing date 10.03.2015 Revision: 10.03.2015

Trade name: SurCoPrimer - FRP Layer I (SCP I)

(Contd. of page 4)

· 8.1 Control parameters

· Ingredients with limit values that require monitoring at the workplace:

The product does not contain any relevant quantities of materials with critical values that have to be monitored at the workplace.

· DNELs No further relevant information available.

· PNECs No further relevant information available.

· Additional information: The lists valid during the making were used as basis.

· 8.2 Exposure controls

· Personal protective equipment:

· General protective and hygienic measures:

The usual precautionary measures are to be adhered to when handling chemicals.

Immediately remove all soiled and contaminated clothing.

Keep away from foodstuffs, beverages and feed.

Wash hands before breaks and at the end of work.

Do not inhale gases / fumes / aerosols.

Avoid contact with the eyes and skin.

· Respiratory protection:

Not required under normal conditions of use.

Use suitable respiratory protective device when high concentrations are present.

Use suitable respiratory protective device when aerosol or mist is formed.

For spills, respiratory protection may be advisable.

· Protection of hands:

Protective gloves

The glove material has to be impermeable and resistant to the product/ the substance/ the preparation.

Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation.

· Material of gloves The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application.

· Penetration time of glove material The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.

· Eye protection:

Contact lenses should not be worn.

Safety glasses

· Body protection: Protective work clothing

· Limitation and supervision of exposure into the environment No further relevant information available.

· Risk management measures See Section 7 for additional information.

(Contd. on page 6)

Page 6/10 according to 1907/2006/EC (REACH), 1272/2008/EC (CLP), and

OSHA GHS

Printing date 10.03.2015 Revision: 10.03.2015

Trade name: SurCoPrimer - FRP Layer I (SCP I)

(Contd. of page 5) No further relevant information available.

SECTION 9: Physical and chemical properties

· 9.1 Information on basic physical and chemical properties

· General Information

· Appearance:

Form: Liquid Colour: Amber coloured

· Odour: Amine-like

· Odour threshold: Not determined.

· pH-value at 20 °C (68 °F): 8 - 8,5

· Change in condition

Melting point/Melting range: Not Determined.

Boiling point/Boiling range: Undetermined.

· Flash point: Not applicable.

· Flammability (solid, gaseous): Not applicable.

· Auto/Self-ignition temperature: Not determined.

· Decomposition temperature: Not determined.

· Self-igniting: Product is not self-igniting.

· Danger of explosion: Product does not present an explosion hazard.

· Explosion limits:

Lower: Not determined.

Upper: Not determined.

· Vapour pressure: Not determined.

· Density at 20 °C (68 °F): 1 g/cm³ (8,345 lbs/gal)

· Relative density Not determined.

· Vapour density Not determined.

· Evaporation rate Not determined.

· Solubility in / Miscibility with water: Not miscible or difficult to mix.

· Partition coefficient (n-octanol/water): Not determined.

· Viscosity:

Dynamic: Not determined.

Kinematic: Not determined.

· 9.2 Other information No further relevant information available.

(Contd. on page 7)

Page 7/10 according to 1907/2006/EC (REACH), 1272/2008/EC (CLP), and

OSHA GHS

Printing date 10.03.2015 Revision: 10.03.2015

Trade name: SurCoPrimer - FRP Layer I (SCP I)

(Contd. of page 6)

SECTION 10: Stability and reactivity

· 10.1 Reactivity

· 10.2 Chemical stability

· Thermal decomposition / conditions to be avoided:

No decomposition if used and stored according to specifications.

· 10.3 Possibility of hazardous reactions Toxic fumes may be released if heated above the decomposition point.

Reacts with strong acids and oxidising agents.

Reacts with strong alkali.

· 10.4 Conditions to avoid Store away from oxidising agents.

· 10.5 Incompatible materials: No further relevant information available.

· 10.6 Hazardous decomposition products:

Carbon monoxide and carbon dioxide Nitrogen oxides (NOx)

SECTION 11: Toxicological information

· 11.1 Information on toxicological effects

· Acute toxicity:

· LD/LC50 values relevant for classification: None.

· Primary irritant effect:

· on the skin: Slight irritant effect on skin and mucous membranes.

· on the eye: Strong irritant with the danger of severe eye injury.

· Sensitisation: No sensitising effects known.

· Subacute to chronic toxicity: No further relevant information available.

· Additional toxicological information:

The product shows the following dangers according to the calculation method of the General EU Classification Guidelines for Preparations as issued in the latest version:

Irritant

· Repeated dose toxicity: No further relevant information available.

SECTION 12: Ecological information

· 12.1 Toxicity

· Aquatic toxicity: No further relevant information available.

· 12.2 Persistence and degradability No further relevant information available.

· 12.3 Bioaccumulative potential No further relevant information available.

· 12.4 Mobility in soil No further relevant information available.

· Additional ecological information:

· General notes:

Water hazard class 1 (German Regulation) (Self-assessment): slightly hazardous for water Do not allow undiluted product or large quantities of it to reach ground water, water course or sewage system.

· 12.5 Results of PBT and vPvB assessment

· PBT: Not applicable.

(Contd. on page 8)

Page 8/10 according to 1907/2006/EC (REACH), 1272/2008/EC (CLP), and

OSHA GHS

Printing date 10.03.2015 Revision: 10.03.2015

Trade name: SurCoPrimer - FRP Layer I (SCP I)

(Contd. of page 7)

· vPvB: Not applicable.

· 12.6 Other adverse effects No further relevant information available.

SECTION 13: Disposal considerations

· 13.1 Waste treatment methods

· Recommendation Small amounts may be diluted with plenty of water and washed away. Dispose of larger amounts in accordance with Local Authority requirements.

Can be burned with household garbage after consulting with the waste disposal facility operator and the pertinent authorities and adhering to the necessary technical regulations.

The user of this material has the responsibility to dispose of unused material, residues and containers in compliance with all relevant local, state and federal laws and regulations regarding treatment, storage and disposal for hazardous and nonhazardous wastes. Residual materials should be treated as hazardous.

· Uncleaned packaging:

· Recommendation: Disposal must be made according to official regulations.

SECTION 14: Transport information

· 14.1 UN-Number

· DOT, ADR, ADN, IMDG, IATA Not Regulated

· 14.2 UN proper shipping name

· DOT, ADR, ADN, IMDG, IATA Not Regulated

· 14.3 Transport hazard class(es)

· DOT, ADR, ADN, IMDG, IATA

· Class Not Regulated

· 14.4 Packing group

· DOT, ADR, IMDG, IATA Not Regulated

· 14.5 Environmental hazards:

· Marine pollutant: No

· 14.6 Special precautions for user Not applicable.

· 14.7 Transport in bulk according to Annex II of MARPOL73/78 and the IBC Code Not applicable.

· UN "Model Regulation": -

SECTION 15: Regulatory information

· 15.1 Safety, health and environmental regulations/legislation specific for the substance or mixture

· United States (USA)

· SARA

· Section 355 (extremely hazardous substances):

None of the ingredients are listed.

(Contd. on page 9)

Page 9/10 according to 1907/2006/EC (REACH), 1272/2008/EC (CLP), and

OSHA GHS

Printing date 10.03.2015 Revision: 10.03.2015

Trade name: SurCoPrimer - FRP Layer I (SCP I)

(Contd. of page 8)

· Section 313 (Specific toxic chemical listings):

None of the ingredients are listed.

· TSCA (Toxic Substances Control Act):

All ingredients are listed.

· Proposition 65 (California):

· Chemicals known to cause cancer:

None of the ingredients is listed.

· Chemicals known to cause reproductive toxicity for females:

None of the ingredients are listed.

· Chemicals known to cause reproductive toxicity for males:

None of the ingredients are listed.

· Chemicals known to cause developmental toxicity:

None of the ingredients are listed.

· Carcinogenic Categories

· EPA (Environmental Protection Agency) None of the ingredients are listed.

· IARC (International Agency for Research on Cancer) None of the ingredients are listed.

· TLV (Threshold Limit Value established by ACGIH) None of the ingredients are listed.

· NIOSH-Ca (National Institute for Occupational Safety and Health) None of the ingredients are listed.

· Canada

· Canadian Domestic Substances List (DSL) All ingredients are listed.

· Canadian Ingredient Disclosure list (limit 0.1%) None of the ingredients are listed.

· Canadian Ingredient Disclosure list (limit 1%) None of the ingredients are listed.

· Other regulations, limitations and prohibitive regulations This product has been classified in accordance with hazard criteria of the Controlled Products Regulations and the SDS contains all the information required by the Controlled Products Regulations.

· Substances of very high concern (SVHC) according to REACH, Article 57 None of the ingredients are listed.

· 15.2 Chemical safety assessment: A Chemical Safety Assessment has not been carried out.

(Contd. on page 10)

Page 10/10 according to 1907/2006/EC (REACH), 1272/2008/EC (CLP), and

OSHA GHS

Printing date 10.03.2015 Revision: 10.03.2015

Trade name: SurCoPrimer - FRP Layer I (SCP I)

(Contd. of page 9)

SECTION 16: Other information This information is based on our present knowledge. However, this shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship.

· Relevant phrases H318 Causes serious eye damage.

R41 Risk of serious damage to eyes.

· Abbreviations and acronyms:

ADR: Accord européen sur le transport des marchandises dangereuses par Route (European Agreement concerning the International Carriage of Dangerous Goods by Road) IMDG: International Maritime Code for Dangerous Goods DOT: US Department of Transportation IATA: International Air Transport Association GHS: Globally Harmonised System of Classification and Labelling of Chemicals ACGIH: American Conference of Governmental Industrial Hygienists EINECS: European Inventory of Existing Commercial Chemical Substances ELINCS: European List of Notified Chemical Substances CAS: Chemical Abstracts Service (division of the American Chemical Society) NFPA: National Fire Protection Association (USA) HMIS: Hazardous Materials Identification System (USA) WHMIS: Workplace Hazardous Materials Information System (Canada) DNEL: Derived No-Effect Level (REACH) PNEC: Predicted No-Effect Concentration (REACH) LC50: Lethal concentration, 50 percent LD50: Lethal dose, 50 percent Eye Dam. 1: Serious eye damage/eye irritation, Hazard Category 1

· Sources SDS Prepared by:

ChemTel Inc.

1305 North Florida Avenue Tampa, Florida USA 33602-2902 Toll Free North America 1-888-255-3924 Intl. +01 813-248-0573 Website: www.chemtelinc.com

Health = 1 Fire = 0 Reactivity = 0

Safety Data Sheet acc. to OSHA HCS (29 CFR 1910.1200) Printing date 08/10/2015 Reviewed on 08/10/2015

1 Identification

· Product identifier

· Trade name: SurCoPrimer - FRP Layer II (SCP II)

· Article number: No other identifiers

· Recommended use and restriction on use

· Recommended use: Surface decontamination.

· Restrictions on use: Contact manufacturer.

· Details of the supplier of the Safety Data Sheet

· Manufacturer/Supplier:

Surtreat Solutions, Inc.

1210 Frick Building 437 Grant Street Pittsburgh, PA 15219 Phone: 412-281-1202

· Emergency telephone number:

ChemTel Inc.

(800)255-3924, +1 (813)248-0585

2 Hazard(s) identification

· Classification of the substance or mixture

Eye Irrit. 2B H320 Causes eye irritation.

· Additional information:

There are no other hazards not otherwise classified that have been identified.

0 percent of the mixture consists of ingredient(s) of unknown toxicity.

· Label elements

· GHS label elements

The product is classified and labeled according to the Globally Harmonized System (GHS).

· Hazard pictograms Not Regulated

· Signal word Warning

· Hazard-determining components of labeling:

silicic acid, sodium salt

· Hazard statements

H320 Causes eye irritation.

· Precautionary statements

P264 Wash thoroughly after handling.

P305+P351+P338 If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.

P337+P313 If eye irritation persists: Get medical advice/attention.

· Classification system:

· NFPA ratings (scale 0 - 4)

(Contd. on page 2)

41.1.0 acc. to OSHA HCS (29 CFR 1910.1200) Printing date 08/10/2015 Reviewed on 08/10/2015

Trade name: SurCoPrimer - FRP Layer II (SCP II)

(Contd. of page 1)

· HMIS-ratings (scale 0 - 4)

HEALTH

FIRE

REACTIVITY

Health = 1 Fire = 0 Reactivity = 0

· Other hazards

· Results of PBT and vPvB assessment

· PBT: Not applicable.

· vPvB: Not applicable.

3 Composition/information on ingredients

· Chemical characterization: Mixtures

· Description: Mixture of the substances listed below with nonhazardous additions.

· Dangerous components:

1344-09-8 silicic acid, sodium salt < 24%

Met. Corr.1, H290; Skin Corr. 1B, H314; Eye Dam. 1, H318

· Additional information:

For the listed ingredient(s), the identity and exact percentage(s) are being withheld as a trade secret.

4 First-aid measures

· Description of first aid measures

· General information: Immediately remove any clothing soiled by the product.

· After inhalation: Supply fresh air; consult doctor in case of complaints.

· After skin contact:

Immediately wash with water and soap and rinse thoroughly.

If skin irritation continues, consult a doctor.

· After eye contact:

Remove contact lenses if worn.

Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.

· After swallowing:

Rinse out mouth and then drink plenty of water.

Do not induce vomiting; immediately call for medical help.

· Information for doctor:

· Most important symptoms and effects, both acute and delayed Slight irritant effect on eyes.

May cause gastro-intestinal irritation if ingested.

· Danger No further relevant information available.

· Indication of any immediate medical attention and special treatment needed No further relevant information available.

(Contd. on page 3) acc. to OSHA HCS (29 CFR 1910.1200) Printing date 08/10/2015 Reviewed on 08/10/2015

Trade name: SurCoPrimer - FRP Layer II (SCP II)

(Contd. of page 2)

5 Fire-fighting measures

· Extinguishing media

· Suitable extinguishing agents:

The product is not flammable.

Use fire fighting measures that suit the environment.

· For safety reasons unsuitable extinguishing agents: None.

· Special hazards arising from the substance or mixture No further relevant information available.

· Advice for firefighters

· Protective equipment:

Wear self-contained respiratory protective device.

Wear fully protective suit.

· Additional information No further relevant information available.

6 Accidental release measures

· Personal precautions, protective equipment and emergency procedures Wear protective equipment. Keep unprotected persons away.

For large spills, use respiratory protective device against the effects of fumes/dust/aerosol.

Ensure adequate ventilation.

· Environmental precautions:

Do not allow undiluted product or large quantities of it to reach ground water, water course or sewage system.

· Methods and material for containment and cleaning up:

Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust).

Dispose contaminated material as waste according to item 13.

Send for recovery or disposal in suitable receptacles.

· Reference to other sections See Section 7 for information on safe handling.

See Section 8 for information on personal protection equipment.

See Section 13 for disposal information.

7 Handling and storage

· Handling:

· Precautions for safe handling Prevent formation of aerosols.

Avoid splashes or spray in enclosed areas.

Use only in well ventilated areas.

· Information about protection against explosions and fires: No special measures required.

· Conditions for safe storage, including any incompatibilities

· Storage:

· Requirements to be met by storerooms and receptacles:

Avoid storage near extreme heat, ignition sources or open flame.

No special requirements.

· Information about storage in one common storage facility:

Store away from foodstuffs.

(Contd. on page 4) acc. to OSHA HCS (29 CFR 1910.1200) Printing date 08/10/2015 Reviewed on 08/10/2015

Trade name: SurCoPrimer - FRP Layer II (SCP II)

(Contd. of page 3) Store away from oxidizing agents.

· Further information about storage conditions: Keep containers tightly sealed.

· Specific end use(s) No further relevant information available.

8 Exposure controls/personal protection

· Additional information about design of technical systems: No further data; see item 7.

· Control parameters

· Components with limit values that require monitoring at the workplace:

The product does not contain any relevant quantities of materials with critical values that have to be monitored at the workplace.

· Additional information: No further relevant information available.

· Exposure controls

· Personal protective equipment:

· General protective and hygienic measures:

The usual precautionary measures for handling chemicals should be followed.

Keep away from foodstuffs, beverages and feed.

Immediately remove all soiled and contaminated clothing.

Wash hands before breaks and at the end of work.

Avoid contact with the eyes and skin.

· Engineering controls: Provide adequate ventilation.

· Breathing equipment:

Not required under normal conditions of use.

Use suitable respiratory protective device when aerosol or mist is formed.

Use suitable respiratory protective device when high concentrations are present.

· Protection of hands:

Protective gloves

The glove material has to be impermeable and resistant to the product/ the substance/ the preparation.

· Eye protection:

Safety glasses

· Body protection:

Not required under normal conditions of use.

Protection may be required for spills.

· Limitation and supervision of exposure into the environment No further relevant information available.

(Contd. on page 5) acc. to OSHA HCS (29 CFR 1910.1200) Printing date 08/10/2015 Reviewed on 08/10/2015

Trade name: SurCoPrimer - FRP Layer II (SCP II)

(Contd. of page 4)

9 Physical and chemical properties

· Information on basic physical and chemical properties

· General Information

· Appearance:

Form: Liquid Color: Clear

· Odor: Mild

· Odor threshold: Not determined.

· pH-value at 20 °C (68 °F): <11.3

· Change in condition

Melting point/Melting range: Undetermined.

Boiling point/Boiling range: >100 °C (>212 °F)

· Flash point: The product is not flammable.

· Flammability (solid, gaseous): Not applicable.

· Auto-ignition temperature: Not determined.

· Decomposition temperature: Not determined.

· Auto igniting: Product is not self-igniting.

· Danger of explosion: Product does not present an explosion hazard.

· Explosion limits:

Lower: Not determined.

Upper: Not determined.

· Oxidizing properties Non-oxidizing.

· Vapor pressure at 20 °C (68 °F): 23 hPa (17 mm Hg)

· Density at 20 °C (68 °F): 1.13 ± 0.04 g/cm³ (9.43 ± 0.334 lbs/gal)

· Relative density Not determined.

· Vapour density Not determined.

· Evaporation rate Not determined.

· Solubility in / Miscibility with

Water: Fully miscible.

· Partition coefficient (n-octanol/water): Not determined.

· Viscosity:

Dynamic: Not determined.

Kinematic: Not determined.

· Other information No further relevant information available.

10 Stability and reactivity

· Reactivity No further relevant information available.

(Contd. on page 6) acc. to OSHA HCS (29 CFR 1910.1200) Printing date 08/10/2015 Reviewed on 08/10/2015

Trade name: SurCoPrimer - FRP Layer II (SCP II)

(Contd. of page 5)

· Chemical stability

· Thermal decomposition / conditions to be avoided:

No decomposition if used and stored according to specifications.

· Possibility of hazardous reactions Reacts with strong oxidizing agents.

Reacts with strong alkali.

· Conditions to avoid No further relevant information available.

· Incompatible materials: No further relevant information available.

· Hazardous decomposition products: Possible in traces.

11 Toxicological information

· Information on toxicological effects

· Acute toxicity:

· LD/LC50 values that are relevant for classification: None.

· Primary irritant effect:

· on the skin: Based on available data, the classification criteria are not met.

· on the eye: Slight irritant effect on eyes.

· Sensitization: Based on available data, the classification criteria are not met.

· Additional toxicological information:

Swallowing will lead to a strong caustic effect on mouth and throat and to the danger of perforation of esophagus and stomach.

· Carcinogenic categories

· NTP (National Toxicology Program) None of the ingredients is listed.

· OSHA-Ca (Occupational Safety & Health Administration) None of the ingredients is listed.

· Probable Routes of Exposure Ingestion.

Inhalation.

Eye contact.

Skin contact.

· CMR effects (carcinogenity, mutagenicity and toxicity for reproduction):

· Germ cell mutagenicity Based on available data, the classification criteria are not met.

· Carcinogenicity Based on available data, the classification criteria are not met.

· Reproductive toxicity Based on available data, the classification criteria are not met.

· STOT-single exposure Based on available data, the classification criteria are not met.

· STOT-repeated exposure Based on available data, the classification criteria are not met.

· Aspiration hazard Based on available data, the classification criteria are not met.

12 Ecological information

· Toxicity

· Aquatic toxicity: No further relevant information available.

· Persistence and degradability No further relevant information available.

(Contd. on page 7) acc. to OSHA HCS (29 CFR 1910.1200) Printing date 08/10/2015 Reviewed on 08/10/2015

Trade name: SurCoPrimer - FRP Layer II (SCP II)

(Contd. of page 6)

· Behavior in environmental systems:

· Bioaccumulative potential No further relevant information available.

· Mobility in soil No further relevant information available.

· Additional ecological information:

· General notes:

Do not allow undiluted product or large quantities of it to reach ground water, water course or sewage system.

Rinse off of bigger amounts into drains or the aquatic environment may lead to increased pH-values. A high pH-value harms aquatic organisms. In the dilution of the use-level the pH-value is considerably reduced, so that after the use of the product the aqueous waste, emptied into drains, is only low water-dangerous.

· Other adverse effects No further relevant information available.

13 Disposal considerations

· Waste treatment methods

· Recommendation:

The user of this material has the responsibility to dispose of unused material, residues and containers in compliance with all relevant local, state and federal laws and regulations regarding treatment, storage and disposal for hazardous and nonhazardous wastes. Residual materials should be treated as hazardous.

· Uncleaned packagings:

· Recommendation: Disposal must be made according to official regulations.

14 Transport information

· UN-Number

· DOT, ADR, IMDG, IATA Not Regulated

· UN proper shipping name

· DOT, ADR, IMDG, IATA Not Regulated

· Transport hazard class(es)

· DOT, ADR, ADN, IMDG, IATA

· Class Not Regulated

· Packing group

· DOT, ADR, IMDG, IATA Not Regulated

· Environmental hazards:

· Marine pollutant: No

· Special precautions for user Not applicable.

· Transport in bulk according to Annex II of MARPOL73/78 and the IBC Code Not applicable.

· UN "Model Regulation": Not Regulated

(Contd. on page 8) acc. to OSHA HCS (29 CFR 1910.1200) Printing date 08/10/2015 Reviewed on 08/10/2015

Trade name: SurCoPrimer - FRP Layer II (SCP II)

(Contd. of page 7)

15 Regulatory information

· Safety, health and environmental regulations/legislation specific for the substance or mixture

· United States (USA)

· SARA

· Section 355 (extremely hazardous substances):

None of the ingredients is listed.

· Section 313 (Specific toxic chemical listings):

None of the ingredients are listed.

· TSCA (Toxic Substances Control Act):

All ingredients are listed.

· Proposition 65 (California)

· Chemicals known to cause cancer:

None of the ingredients are listed.

· Chemicals known to cause reproductive toxicity for females:

None of the ingredients are listed.

· Chemicals known to cause reproductive toxicity for males:

None of the ingredients is listed.

· Chemicals known to cause developmental toxicity:

None of the ingredients is listed.

· Carcinogenic categories

· EPA (Environmental Protection Agency) None of the ingredients is listed.

· IARC (International Agency for Research on Cancer) None of the ingredients is listed.

· TLV (Threshold Limit Value established by ACGIH) None of the ingredients is listed.

· NIOSH-Ca (National Institute for Occupational Safety and Health) None of the ingredients is listed.

· State Right to Know Listings None of the ingredients is listed.

· Canadian substance listings:

· Canadian Domestic Substances List (DSL) All ingredients are listed.

· Canadian Ingredient Disclosure list (limit 0.1%) None of the ingredients is listed.

· Canadian Ingredient Disclosure list (limit 1%) None of the ingredients is listed.

(Contd. on page 9) acc. to OSHA HCS (29 CFR 1910.1200) Printing date 08/10/2015 Reviewed on 08/10/2015

Trade name: SurCoPrimer - FRP Layer II (SCP II)

(Contd. of page 8)

· Other regulations, limitations and prohibitive regulations This product has been classified in accordance with hazard criteria of the Controlled Products Regulations and the SDS contains all the information required by the Controlled Products Regulations.

· Chemical safety assessment: A Chemical Safety Assessment has not been carried out.

16 Other information This information is based on our present knowledge. However, this shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship.

· Date of preparation / last revision 08/10/2015 / -

· Abbreviations and acronyms:

ADR: Accord européen sur le transport des marchandises dangereuses par Route (European Agreement concerning the International Carriage of Dangerous Goods by Road) IMDG: International Maritime Code for Dangerous Goods DOT: US Department of Transportation IATA: International Air Transport Association ACGIH: American Conference of Governmental Industrial Hygienists EINECS: European Inventory of Existing Commercial Chemical Substances ELINCS: European List of Notified Chemical Substances CAS: Chemical Abstracts Service (division of the American Chemical Society) NFPA: National Fire Protection Association (USA) HMIS: Hazardous Materials Identification System (USA) WHMIS: Workplace Hazardous Materials Information System (Canada) LC50: Lethal concentration, 50 percent LD50: Lethal dose, 50 percent Met. Corr.1: Corrosive to metals, Hazard Category 1 Skin Corr. 1B: Skin corrosion/irritation, Hazard Category 1B Eye Dam. 1: Serious eye damage/eye irritation, Hazard Category 1 Eye Irrit. 2B: Serious eye damage/eye irritation, Hazard Category 2B

· Sources SDS Prepared by:

ChemTel Inc.

1305 North Florida Avenue Tampa, Florida USA 33602-2902 Toll Free North America 1-888-255-3924 Intl. +01 813-248-0573 Website: www.chemtelinc.com