Addendum Plan SheetsPart-6.pdf

A D A D D 1

WALL SECTIONS

AS-411

JFB, IAR,

JY

RM, IAR

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

Office of Construction and Facilities Management

U.S. Department of Veterans

Affairs

PhasePROJECT MANAGEMENT STAMPCONSULTANT

FULLY SPRINKLERED

DESIGN

San Antonio, Texas 78217

ARCHITECTURE

8718 BOTTS LANE

Tel: (210) 881-9714

HFS COMPANY

ENGINEERING

Fax: (210) 881-6808 jbianco@hfscompany.com 11/30/21

CONSTRUCTION BID

DOCUMENTS

CONSTRUCT COMBINED

ENERGY PLANT PHASE 1

4101 WOOLWORTH AVE.

OMAHA, NE 68105

11/30/2021

636-18-304

ETS

T

TA

GE

S

R I

E T EX

FO

T

CE

TI

H

AS

DER CRA

F. BIAN

C

OJO

SE

P

H

7 6 22 1

Revisions: Date:

WALL SECTION

SCALE: 1/2" = 1'-0"

WALL SECTION

SCALE: 1/2" = 1'-0"

WALL SECTION

SCALE: 1/2" = 1'-0"

WALL SECTION

SCALE: 1/2" = 1'-0"

WALL SECTION

SCALE: 1/2" = 1'-0"

WALL SECTION

SCALE: 1/2" = 1'-0"

EAST ELEVATION - CHILLER PLANT

SCALE: 1/4" = 1'-0"

EAST ELEVATION - CORRIODR/STAIRS

SCALE: 1/4" = 1'-0"

SOUTH ELEVATION - STAFF TOILET

SCALE: 1/4" = 1'-0"

ENLARGED FLOOR PLAN - STAFF TOILET

SCALE: 1/4" = 1'-0"

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

Office of Construction and Facilities Management

U.S. Department of Veterans

Affairs

PhasePROJECT MANAGEMENT STAMPCONSULTANT

FULLY SPRINKLERED

DESIGN

San Antonio, Texas 78217

ARCHITECTURE

8718 BOTTS LANE

Tel: (210) 881-9714

HFS COMPANY

ENGINEERING

Fax: (210) 881-6808 jbianco@hfscompany.com 11/30/21

CONSTRUCTION BID

DOCUMENTS

CONSTRUCT COMBINED

ENERGY PLANT PHASE 1

4101 WOOLWORTH AVE.

OMAHA, NE 68105

11/30/2021

636-18-304

ETS

T

TA

GE

S

R I

E T EX

FO

T

CE

TI

H

AS

DER CRA

F. BIAN

C

OJO

SE

P

H

7 6 22 1

Revisions: Date:

AS-510

INTERIOR ELEVATIONS

RACJFB, IAR,

JY

SECTION DETAIL

SCALE: 3" = 1'-0"

SECTION DETAIL

SCALE: 3" = 1'-0"

2 1

2 1

SECTION DETAIL

SCALE: 3" = 1'-0"

SECTION DETAIL

SCALE: 3" = 1'-0"

SECTION DETAIL

SCALE: 3" = 1'-0"

SECTION DETAIL

SCALE: 3" = 1'-0"

A

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

Office of Construction and Facilities Management

U.S. Department of Veterans

Affairs

PhasePROJECT MANAGEMENT STAMPCONSULTANT

FULLY SPRINKLERED

DESIGN

San Antonio, Texas 78217

ARCHITECTURE

8718 BOTTS LANE

Tel: (210) 881-9714

HFS COMPANY

ENGINEERING

Fax: (210) 881-6808 jbianco@hfscompany.com 11/30/21

CONSTRUCTION BID

DOCUMENTS

CONSTRUCT COMBINED

ENERGY PLANT PHASE 1

4101 WOOLWORTH AVE.

OMAHA, NE 68105

11/30/2021

636-18-304

ETS

T

TA

GE

S

R I

E T EX

FO

T

CE

TI

H

AS

DER CRA

F. BIAN

C

OJO

S

EP

H

7 6 22 1

Revisions: Date:

AS-600

SECTION DETAILS

JFB, IAR,

DJ, IAR

D

SECTION DETAIL

SCALE: 3' = 1'-0"

SECTION DETAIL

SCALE: 3' = 1'-0"

D

SECTION DETAIL

SCALE: 3' = 1'-0"

SECTION DETAIL

SCALE: 3' = 1'-0"

SECTION DETAIL

SCALE: 3' = 1'-0"

D

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

Office of Construction and Facilities Management

U.S. Department of Veterans

Affairs

PhasePROJECT MANAGEMENT STAMPCONSULTANT

FULLY SPRINKLERED

DESIGN

San Antonio, Texas 78217

ARCHITECTURE

8718 BOTTS LANE

Tel: (210) 881-9714

HFS COMPANY

ENGINEERING

Fax: (210) 881-6808 jbianco@hfscompany.com 11/30/21

CONSTRUCTION BID

DOCUMENTS

CONSTRUCT COMBINED

ENERGY PLANT PHASE 1

4101 WOOLWORTH AVE.

OMAHA, NE 68105

11/30/2021

636-18-304

ETS

T

TA

GE

S

R I

E T EX

FO

T

CE

TI

H

AS

DER CRA

F. BIAN

C

OJO

S

EP

H

7 6 22 1

Revisions: Date:

AS-601

SECTION DETAILS

JFB, IAR,

DJ, IAR

B I M

A

L M

V A

H

R

E N

O V

A T

E

O

R A

L M

V A

H R

E N

O V

A T

E O

R r v t

P

M

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

Office of Construction and Facilities Management

U.S. Department of Veterans

Affairs

PhasePROJECT MANAGEMENT STAMPCONSULTANT

FULLY SPRINKLERED

DESIGN

San Antonio, Texas 78217

ARCHITECTURE

8718 BOTTS LANE

Tel: (210) 881-9714

HFS COMPANY

ENGINEERING

Fax: (210) 881-6808 jbianco@hfscompany.com 11/30/21

CONSTRUCTION BID

DOCUMENTS

CONSTRUCT COMBINED

ENERGY PLANT PHASE 1

4101 WOOLWORTH AVE.

OMAHA, NE 68105

11/30/2021

636-18-304

ETS

T

TA

GE

S

R I

E T EX

FO

T

CE

TI

H

AS

DER CRA

F. BIAN

C

OJO

S

EP

H

7 6 22 1

Revisions: Date:

AS-700

SCHEDULES, DOOR TYPES, FRAME

TYPES & LOUVER TYPES

JFB, IAR,

JY

IAR, RAC

ROOM NAME

DOOR

NUMBER

DOOR FRAME

HARDWARE

GROUP

LABEL

RATING REMARKSWIDTH HEIGHT MATERIAL FINISH TYPE MATERIAL FINISH TYPE HEAD

DOOR SCHEDULE

JAMB SILL

DETAILS

ABBREVIATIONS: REMARKS:

GROUND LEVEL

ROOM NAME

DOOR

NUMBER

DOOR FRAME

HARDWARE

GROUP

LABEL

RATING REMARKSWIDTH HEIGHT MATERIAL FINISH TYPE MATERIAL FINISH TYPE HEAD JAMB SILL

DETAILS

MEZZANINE LEVEL

TYPE WIDTH HEIGHT GLAZING FRAME COMMENTSU-VALUE SHGC

WINDOW SCHEDULE

ABBREVIATIONS: REMARKS:

TYPE WIDTH HEIGHT MATERIAL FINISH

LOUVER SCHEDULE

ABBREVIATIONS: REMARKS:

WALL

RATING REMARKSHEAD JAMB SILL

DETAILS

WINDOW HEAD

SCALE: 3" = 1'-0"

WINDOW JAMB

SCALE: 3" = 1'-0"

WINDOW SILL

SCALE: 3" = 1'-0"

LOUVER HEAD

SCALE: 3" = 1'-0"

LOUVER JAMB

SCALE: 3" = 1'-0"

LOUVER SILL

SCALE: 3" = 1'-0"

A

DOOR SILL

SCALE: 3" = 1'-0"

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

Office of Construction and Facilities Management

U.S. Department of Veterans

Affairs

PhasePROJECT MANAGEMENT STAMPCONSULTANT

FULLY SPRINKLERED

DESIGN

San Antonio, Texas 78217

ARCHITECTURE

8718 BOTTS LANE

Tel: (210) 881-9714

HFS COMPANY

ENGINEERING

Fax: (210) 881-6808 jbianco@hfscompany.com 11/30/21

CONSTRUCTION BID

DOCUMENTS

CONSTRUCT COMBINED

ENERGY PLANT PHASE 1

4101 WOOLWORTH AVE.

OMAHA, NE 68105

11/30/2021

636-18-304

ETS

T

TA

GE

S

R I

E T EX

FO

T

CE

TI

H

AS

DER CRA

F. BIAN

C

OJO

S

EP

H

7 6 22 1

Revisions: Date:

AS-711

WINDOW & LOUVER DETAILS

JFB, IAR,

IAR, RC

FUTURE EXPANSION

3"S-DN

3/4"CW-DN

P-802

3" VTR

3/4"CW-UP

XXX-11

CHILLER PLANT

3431 SQFT

3" VTR

3" VTR3" VTR

TO P-815 ON ROOF

XXX-XX

MEZZANINE

803 SQFT

AHU

S

3" V

3" V

A B C D

3"V-UP

4"CW-UP

3" FD-E

3" FD-S

HX

HWP

HWP

HX

ET

"C

W

1 1/2"CW

1"CW

AHU

3" FD-E

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

CONSTRUCTION BID

DOCUMENTS

FULLY SPRINKLERED

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

PRIME CONSULTANT STAMPCONSULTANT

321 4 5 6 7 8 9 10

636-18-304

X

CONSTRUCT COMBINED

ENERGY PLANT PHASE 1

5350 W 94TH TERRACE #102

PRAIRIE VILLAGE, KS 66207

T 913.258.5026 www.rossbar.com

4101 WOOLWORTH AVE

OMAHA, NE 68105

11/30/2021

NOT F

OR

CONSTRUCTIO

N

D U s e rs

\r c o o p e r\ D o c u m e n ts

\2

-1

P

L U

M B v ry a n .c o o p e rX

T C

R S

.r v t

/5

/2

:1

:2

P M

XX-P-102

PLUMBING MEZZANINE PLAN

JES RLC

1/8" = 1'-0"

PLUMBING NEW WORK - MEZZANINE LEVEL

TRUE

NORTHPLAN

NORTH

A. REFER TO 0-P-000 FOR PLUMBING SYMBOLS AND

ABBREVIATIONS.

GENERAL SHEET NOTES

1. SEE MECHANICAL DRAWINGS FOR ADDITIONAL

INFORMATION.

KEYED NOTES#

Revisions: Date:

ADDENDUM NO. 01 04/07/2022 04/07/2022

CWR

CWS

CWR

CWS

CWR

CWS

CWR

CWS

FS

FS

FS

FS

FS

FS

CWR

CWS

CWS

CWS

CWS

CWR

CWR

CWR

CWM

NC

BYPASS

P-16

P-17

P-14

P-15

P-6

P-7

300 GPM

120 GPM

90 GPM

FROM RESEARCH

8" FOR TEMP

CHILLER

FROM CC-3

FROM CC-1

TO CC-1

TO

RESEARCH

TO CC-3

CC-2

NO

AMBULATORY CARE

TO INDUCTION UNITS ON

FLRS 1-4

TO INDUCTION UNITS ON

FLRS 5-11

NO

NO

CV-7CV-6

FILL

VALVE

TO

FLOOR

DRAIN

DRAIN

VALVE

CWS

CWR

16" CWR

CWR

CWR

CWR

14" CWR

CWS

CWS

CWS

C W

S

3" NPCW DOWNSTREAM OF METER &

BACKFLOW PREVENTERS

ALL EXISTING PUMPS TO

REMAIN

3" DCW

24" CR

C W

R

C W

S

CH-X

CH-1 BACKUP

EXISTING TRANE

"TEMP" CHILLER

1250 TON

OUTDOOR

MODULAR

CHILLER

(ETR)

RELOCATED CHILLER

ENCLOSURE

14" CS

14" CR

ET

WCC

WCC

16" CWS

20" CWR

20" CWS

24" CS

24" CS

14" CR

CT

CT

14" CS

16" CR

16" CR

CTP

CTP

CTP

CWP

CWP

CWP

24" CS

C R

12" CWR

ROUTE DOWN

TO CAMPUS

LOOP24" CWR

FUTURE

WCC-3

FUTURE

WCC-4

VALVE AND CAP FOR

FUTURE CHILLER INSTALL

(TYP)

2" NPW

3" NPW

2" NPW

12" CWS

20" DECOUPLER

ADS-1

ADS-1

BYPASS

20" CWS/CWR24" CWS/CWR

24" CWS

PIPE TRANSITION BETWEEN

NEW CHILLER PLANT AND

UNDERGROUND

M

14" CWS/R TO

TEMP ACC'S

CWP

FUTURE

B17 BYPASS

DP

18" EQUALIZER

LINE

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

CONSTRUCTION BID

DOCUMENTS

FULLY SPRINKLERED

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

PRIME CONSULTANT STAMPCONSULTANT

321 4 5 6 7 8 9 10

636-18-304

X

CONSTRUCT COMBINED

ENERGY PLANT PHASE 1

5350 W 94TH TERRACE #102

PRAIRIE VILLAGE, KS 66207

T 913.258.5026 www.rossbar.com

4101 WOOLWORTH AVE

OMAHA, NE 68105

11/30/2021

NOT F

OR

CONSTRUCTIO

N

D U s e rs

\m s im m o n s \D o c u m e n ts

\2 -1

M

E C

H v m s im m o n s L W

R W

.r v t

/5

/2

:5 :4

P

M

0-M-201

MECHANICAL FLOW DIAGRAMS - CHILLED

WATER MODIFICATIONS

JES MDS

NOT TO SCALE

MECHANICAL ROOM PIPING SCHEMATIC -

NEW

Revisions: Date:

ADDENDUM NO. 01 04/07/2022

04/07/2022

ABCD

CT

CT

COOLING TOWER SUPPORT

STRUCTURE. REFER TO

STRUCTURAL PLANS.

24" CS 24" CR

C S

24" CS 24" CR

4" NPWR

4" NPWR4" NPWS

WCC

WCC

CTF

CTF

4" NPWS

4" NPWS

12" CS

10" CS

16" CR 16" CR

16" CR

16" CR

C W

R

C W

S

14" CS

14" CS

14" CR

4" NPWR

4" NPWS4" NPWS

18" CR

18" CR

16" CR

14" CS 14" CS

14" CS14" CS

6" CWR

6" CWS

20" CR

18" CR

CTP

CWP

8" CWR

6" CWR

E-2

E-2

ET

SEE SCHEDULES ON SHEET

0-M-601 FOR MAXIMUM UNIT

DIMENSIONS AND

WEIGHTS. COORDINATE

WITH STRUCTURAL

SUPPORTS AND ACCESS

PLATFORMS.

12" CWR

12" CWS

12" CWR

12" CWS

14" CR

24" CR

20" CR

14" CR

2 1

AHU

30x74 SA

34x70 RA

54x96 OA

LU-1

16850

26x50 SA

A

IR

M

IX

IN

G

S

E C

T

IO

N

C O

O L

IN

G C

O

IL

C

T

IO

N

H E

A T

IN

G

C

C T

IO

N

F A

N S

E C

T

IO

N

OA

ELECTRICAL ROOM BELOW

ACCESS

DOOR

90x106 OA SHEET

METAL PLENUM

ACCESS DOOR

(TYP.4)

STRUCTURAL BEAM

MANUFACTURER PROVIDED

MINIMUM OUTSIDE AIR AND

ECONOMIZER DAMPERS.

SEE 1/0-M-703 FOR RELATED

INFORMATION.

2 1

STRUCTURAL BEAM

AHU

LU-2

A

IR

M

IX

G

C

T

IO

N

C O

O L

IN

G C

C

T

IO

N

H E

A T

IN

G

C

C T

IO

N

F A

N S

E C

T

IO

N

OA

ELECTRICAL ROOM BELOW

ACCESS

DOOR

50x60 OA SHEET

METAL PLENUM

ACCESS DOOR

(TYP.4)

MANUFACTURER PROVIDED

MINIMUM OUTSIDE AIR AND

ECONOMIZER DAMPERS.

SEE 1/0-M-703 FOR RELATED

INFORMATION.

16x45 OA 18x46 RA14x36 SA

14x36 SA24x12 SA

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

CONSTRUCTION BID

DOCUMENTS

FULLY SPRINKLERED

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

PRIME CONSULTANT STAMPCONSULTANT

321 4 5 6 7 8 9 10

636-18-304

X

CONSTRUCT COMBINED

ENERGY PLANT PHASE 1

5350 W 94TH TERRACE #102

PRAIRIE VILLAGE, KS 66207

T 913.258.5026 www.rossbar.com

4101 WOOLWORTH AVE

OMAHA, NE 68105

11/30/2021

NOT F

OR

CONSTRUCTIO

N

D U s e rs

\m s im m o n s \D o c u m e n ts

\2 -1

M

E C

H v m s im m o n s L W

R W

.r v t

/5

/2

:5 :4

P

M

0-M-301

MECHANICAL SECTIONS

JES MDS

1/4" = 1'-0"

COOLING TOWERS

1/4" = 1'-0"

MEZZANINE AHU-1

Revisions: Date:

ADDENDUM NO. 01 04/07/2022

1/4" = 1'-0"

MEZZANINE AHU-2

I v

ELECTRICAL EQUIPMENT

OVERHEAD DOOR

CONTROLS

14" CRREMOVE ALL EXISTING

PUMPS AND SPECIALTIES

FROM EXISTING

OUTDOOR CHILLER

ENCLOSURE. PUMP

LOCATION SHOW IS

APPROXIMATE AND FOR

REFERNECE ONLY.

CONFIRM FINAL CONNECTION

WITH MANUFACTURER

C S

C R

C S

C R

C W

S

C W

R

12" CWR

12" CWS

14" CS

REMOVE ALL EXISTING

PUMPS AND SPECIALTIES

FROM EXISTING

OUTDOOR CHILLER

ENCLOSURE. PUMP

LOCATION SHOW IS

APPROXIMATE AND FOR

REFERNECE ONLY.

PROVIDE FLEXIBLE PIPE

CONNECTION AT

OUTDOOR CHILLER

ENCLOSURE.

(TYP 4)

3' MAN DOOR

3' MAN DOOR

COORDINATE

RELOCATION OF CHILLER

WITH EXISTING

EQUIPMENT. EXISTING

REFRIGERANT AND OIL

TO BE EVACUATED PRIOR

TO RELOCATION AND

REFILLED UPON NEW

LOCATION.

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

CONSTRUCTION BID

DOCUMENTS

FULLY SPRINKLERED

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

PRIME CONSULTANT STAMPCONSULTANT

321 4 5 6 7 8 9 10

636-18-304

X

CONSTRUCT COMBINED

ENERGY PLANT PHASE 1

5350 W 94TH TERRACE #102

PRAIRIE VILLAGE, KS 66207

T 913.258.5026 www.rossbar.com

4101 WOOLWORTH AVE

OMAHA, NE 68105

11/30/2021

D U s e rs

\m s im m o n s \D o c u m e n ts

\2 -1

M

E C

H v m s im m o n s L W

R W

.r v t

/5

/2

:5 :5

P

M

0-M-401

MECHANICAL ENLARGED PLAN - EXISTING

CHILLER

JES RLC

1/2" = 1'-0"

MECHANICAL ENLARGED DESIGN PLAN -

EXISTING CHILLER

TRUE NORTH

Revisions: Date:

ROOF INSULATION

FASTEN ANGLE IRON

SECURELY TO DUCT

AND ROOF STRUCTURE

SECURE CURB TO

ROOF WITH SCREWS,

PINS, OR BOLTS

EXTEND DUCTWORK

OVER TOP OF CURB,

SECURE DUCTWORK

TO CURB NAILER

EXHAUST FAN

WITH BIRDSCREEN

SECURE EXHAUST FAN TO

ROOF CURB

PREFABRICATED

INSULATED CURB WITH

TREATED WOOD NAILER.

COUNTER BALANCED BACKDRAFT

(UNLESS NOTED OTHERWISE)

DAMPER, SECURE TO DUCT FROM

ABOVE TO ALLOW SERVICE OR

REMOVAL OF DAMPER FROM ROOF

ROOF DECK REFER TO

ARCHITECTURAL DRAWINGS

EXHAUST DUCT UP THROUGH

ROOF. SEE PLANS FOR SIZE

AND LOCATION.

VANE

VANE

R SHALL

EQUAL OR

BE

GREATER

THAN W.

R SHALL

EQUAL OR

BE

GREATER

THAN

1/3W.

R SHALL

EQUAL OR

BE

GREATER

THAN

1/6W.

SHORT RADIUS ELBOW

WITH TWO VANES

SHORT RADIUS ELBOW

WITH ONE VANE

STANDARD RADIUS OR

LONG RADIUS ELBOW

THE INTERIOR SURFACE OF ALL RADIUS ELBOWS SHALL BE MADE ROUND.

ALL STANDARD RADIUS ELBOWS CAN BE SUBSTITUTED WITH SHORT RADIUS ELBOWS. ALL

SHORT RADIUS ELBOWS SHALL HAVE VANES. VANES SHALL BE CONSTRUCTED, SUPPORTED

AND FASTENED AS RECOMMENDED BY SMACNA.

NOTE:

1.

2.

W

R

1/6W

/3

W

1/2W

W

/3

W

2/3W

R

R

W

ALL VANE ELBOWS SHALL BE CONSTRUCTED AND INSTALLED AS DETAILED BY SMACNA.

WHEN W1 DOES NOT EQUAL W2, VANE SHALL BE SINGLE THICKNESS VANE TYPE

REGARDLESS OF W DIMENSION.

ALL SINGLE THICKNESS VANES SHALL HAVE A 2" [50mm] RADIUS, 1 1/2" [40mm] MAXIMUM

SPACE BETWEEN VANES AND A 3/4" [20mm] TRAILING EDGE.

WHEN W EQUALS W2 AND W1 IS GREATER THAN 20" [500mm] VANES SHALL BE DOUBLE VANE

TYPE.

NOTE:

1.

2.

3.

4.

W1

W

M

AX.

M A

X

E Q

U

IP

M E

N T

M

AX.

M A

X

M A

X

M A

X

TYPICAL DUCTWORK TRANSITION

PLAN OR SIDE VIEWTYPICAL DUCTWORK TRANSITION WITH

EQUIPMENT MOUNTED IN DUCT

PLAN OR SIDE VIEW

AIR

FLOW

AIR

FLOW

NOTE:

UNLESS OTHERWISE INDICATED ON PLANS, MAXIMUM ANGLES SHOWN SHALL APPLY.

15°

MAIN EXHAUST OR RETURN

PLAN VIEW

AIR

FLOW AIR

FLOW

PROVIDE VOLUME DAMPER

AT EACH BRANCH DUCT

1/4W OR 4" [100mm]

MIN.

BRANCH DUCT

VD

W

FROM STRUCTURE

SAME AS DIFFUSER

INLET: 5'-0" MAX

FLEXIBLE DUCT SIZE

LENGTH.

12"

CEILING

SUPPORT SADDLE

VOLUME DAMPER W/

LOCKING QUADSADDLE

SHEET METAL

CONICAL OUTLET

BRANCH DUCT

FOR CHANGE OF

DIRECTION GREATER

USE RIGID ELBOWS

THAN 45°

[300mm]

SEE SPECIFICATIONS FOR CLAMPS

AND SEALANT (TYP.)

THERMAL INSULATION

SEE SPECIFICATIONS

TYPICAL

DIFFUSER OR

REGISTER IN

LAY-IN CLG.

NOTE:

1. THE USE OF FLEXIBLE AIR DUCT CONNECTORS ARE NOT PERMITTED

FOR THE DEDICATED AHU SERVING THE SURGICAL SUITE.

D

D

NOTE:

1.

2.

3.

SEE EXPANSION TANK SYSTEM SCHEDULE FOR COMPONENT SIZES.

FOR HOT WATER SYSTEMS 2" [50mm] AND SMALLER AND CHILLED WATER SYSTEMS

USE IN-LINE AIR PURGER IN LIEU OF AIR SEPARATOR.

SET PRESSURE REDUCING VALVE SO PRESSURE AT HIGHEST POINT IN SYSTEM

HAS A MINIMUM OF 4 PSIG [28kPa].

MV CONNECTOR PIPE.

FLOOR MOUNTING BASE RING

WITH DRAIN ACCESS OPENING

SHOWN. ANGLE IRON LEGS MAY

BE USED AS AN OPTION.

COLD WATER FILL LINE.

SEE EXPANSION TANK

SCHEDULE FOR SIZE

RUN DRAIN

LINE TO

NEAREST FD

6" [150mm]

HOUSEKEEPING

PAD

AIR CHARGING

SHRAEDER VALVE

RUN DRAIN LINE TO

NEAREST FD UNLESS

INDICATED OTHERWISE

AIR

SEPARATOR

SEE NOTES 3

& 4

BUTTERFLY

OR BALL

ISOLATION

VALVE

BLADDER

EXPANSION

TANK

FROM SYSTEM

DRAIN

NC

DRAIN

HANGER

RODS (TYP)PI

TO PUMP

SUCTION

AUTO. AIR VENT TO DRAIN

REDUCED PRESSURE BACKFLOW

PREVENTER

DIRECT BURY PIPING. INSULATE

PER SPECIFICATIONS WHERE

REQUIRED.

M

IN

GRANULAR

BACKFILL OR TYPE

2 BASE MATERIAL

MIN

UNDERGROUND MARKING

TAPE 12" (MAX) BELOW GRADE

MINMIN

UNDISTURBED SOIL

AGGREGATE EMBEDMENT PER

SPECIFICATIONS. PARTICLE

SIZE SHALL NOT EXCEED 1-1/2"

FOR PIPE SIZES 18"+

CONCRETE, ASPHALT,

OR TOPSOIL.

CHWS

20"± 6"

6" 6"

CHWS

20"±

FINISHED

GRADE

WHERE TRENCH BOTTOM

CONTAINS FINE GRANULAR

MATERIAL, COMPACT VIA

MANUAL OR MECHANICAL

(PREFERRED) TAMPER

NOTE:

BOTTOM OF UNIT

BASE RAIL

PIPE FULL SIZE OF

AIR HANDLING UNIT

DRAIN CONNECTION

4" HOUSEKEEPING PAD OR ROOF CURB

REMOVABLE CAP

REMOVABLE CAP

FLOW

DRAW-THRU: 1/2 OF NOTE 2 DIMENSION BUT NOT LESS THAN 2"

BLOW-THRU: SCHEDULED E.S.P. THEN ADD 1".

DRAW-THRU: SUBTRACT SCHEDULED E.S.P. FROM T.S.P. THEN ADD

1". BLOW-THRU: 1"

LOCATE TRAPS SO AS TO BE ACCESSIBLE FOR CLEANING.

ROUTE TO NEAREST SANITARY (FLOOR) DRAIN OR ROOF DRAIN.

SLOPE AT 1/4" PER FOOT.

5 CONTRACTOR SHALL INCREASE BASE RAIL HEIGHT AND/OR

HOUSEKEEPING PAD HEIGHT IF NECESSARY TO ACHEIVE

REQUIRED TRAP DIMENSION.

4" STRUCTURAL

SUPPLEMENTAL

STEEL SUPPORT

NOTE:

1.

WALL CONSTRUCTION SYSTEM.

REFER TO ARCHITECTURAL

DRAWINGS.

EXHAUST DUCT.

SEE PLAN FOR SIZE.

BIRDSCREEN

REFER TO ARCHITECTURAL DRAWINGS FOR WALL PENETRATION DETAILS.

COORDINATE ALL PENETRATIONS WITH GENERAL CONTRACTOR.

MOUNTING BOLTS

SIDEWALL MOUNTED

CENTRIFUGAL

UPBLAST EXHAUST FAN AS

SCHEDULED

CONNECT DUCTWORK TO FAN'S FRAME

HOUSING USING FLANGE AND BOLTED

CONNECTION PER FAN

MANUFACTURER'S

INSTRUCTIONS

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

CONSTRUCTION BID

DOCUMENTS

FULLY SPRINKLERED

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

PRIME CONSULTANT STAMPCONSULTANT

321 4 5 6 7 8 9 10

636-18-304

X

CONSTRUCT COMBINED

ENERGY PLANT PHASE 1

5350 W 94TH TERRACE #102

PRAIRIE VILLAGE, KS 66207

T 913.258.5026 www.rossbar.com

4101 WOOLWORTH AVE

OMAHA, NE 68105

11/30/2021

NOT F

OR

CONSTRUCTIO

N

D U s e rs

\m s im m o n s \D o c u m e n ts

\2 -1

M

E C

H v m s im m o n s L W

R W

.r v t

/5

/2

:5 :5

P

M

0-M-501

MECHANICAL DETAILS

JES MDS

NOT TO SCALE

DOWNBLAST EXHAUST FAN

NOT TO SCALE

DUCTWORK RADIUS ELBOWS

NOT TO SCALE

DUCTWORK SQUARE VANE ELBOWS

NOT TO SCALE

DUCTWORK TRANSITIONS (WITH

EQUIPMENT MOUNTED IN DUCT)

NOT TO SCALE

EXHAUST OR RETURN BRANCH

DUCTWORK

NOT TO SCALE

FLEXIBLE AIR DUCT CONNECTOR

NOT TO SCALE

FLOOR MOUNTED EXPANSION TANK -

PIPING CONNECTIONS

NTS

PPRCT PLASTIC PIPING

DIRECT BURIAL DETAIL

Revisions: Date:

ADDENDUM NO. 01 04/07/2022

NTS

CONDENSATE DRAIN TRAP

NOT TO SCALE

SIDEWALL MOUNTED UPBLAST EXHAUST

FAN DETAIL

TO DRAIN

MV

MANUAL

AIR VENT

TO BUILDING

LOAD

INVERTED BUCKET

TRAP ASSEMBLY

WELDED

TEE

12"[300 MM]

6"[150 MM]

SCHEDULE 80 STEEL PIPE

1" GATE VALVE

CONDENSATE

STEAM PIPE

A SIZE, TRAP DISCHARGE LINE 1/2" [15mm] 3/4" [20mm]

1-1/4" [32mm]1" [25mm]SIZE, 45° WELDING NIPPLEB

C 7" [175mm] 7" [175mm]

16-1/2" [415mm]16-1/2" [415mm]

2" [50mm]2" [50mm]

LENGTH OF PERFORATED PIPED

E

RETURN MAIN SIZE UP TO 1-1/2" [40mm] 2" [50mm] 3" [75mm] & OVER

SAME SIZE2-1/2" [65mm]EXPANDED RETURN MAIN SIZE

EXPANDED RETURN MAIN

SECTION A-A

WELD CAP

EXPANDED RETURN MAIN CAP

REDUCER

INCREASER

A

B

A

A

FLOW

SECTION-EXPANDED RETURN MAIN

PERFORATED TUBE 1"x1/8" [25x6mm]

THICK GUIDE FINS WELDED TO

PERFORATED TUBE

PERFORATED

TUBE

RETURN

MAIN

LENGTH OF EXPANDED MAIN OF

FOLLOWING PERFORATED PIPE

LENGTH OF EXPANDED MAIN AHEAD

OF TRAP DISCHARGE PIPE

EDC

NOTES:

1.

2.

3.

1/2" [15mm] PERFORATED TUBE SHALL HAVE 40 - 1/8" [16mm] DIAMETER HOLES

SPACED 1-1/2" [40mm] O.C. IN 4 ROWS.

3/4" [20mm] PERFORATED TUBE SHALL HAVE 78 - 1/8" [6mm] DIAMTER HOLES

SPACED 1-1/2" [40mm] O.C. IN 6 ROWS.

HOLES IN TUBE SHALL BE SPACED EQUALLY AROUND PERIMETER.

BLOWDOWN

ELEVATION

1/2" [15mm] STEEL PIPE OR

STEEL TUBING TO SENSORS

DIFFERENTIAL PRESSURE

TRANSMITTER (FLOW, LEVEL)

PT

INSTALLATION OF SENSORS AND TRANSMITTERS SHALL CONFORM TO

RECOMMENDATIONS OF MANUFACTURERS OF TRANSMITTERS.

NOTES:

1.

BUILDING INCOMING

MAIN STEAM

TO METERING

SYSTEM

SHUTOFF VALVE

DIFFERENTIAL PRESSURE (DP) CEL

STEAM FLOW MEASUREMENT

FLOW METER

INTERFACE

WITH BACNET

SYSTEM

TEMPERATURE

TRANSMITTER

PRESSURE

TRANSMITTER

PT

TT

MAINTAIN UPSTREAM AND DOWN STREAM DISTANCES RECOMMENDED BY METER MANUFACTURES

NOTE:

1.

NOTE:

1.

2.

3.

4.

SEE FLOOR PLANS FOR PIPE SIZES.

SEE EQUIPMENT SCHEDULES FOR VALVE DATA AND PIPE SIZES D1 AND D2. INSTALL

VALVES AS RECOMMENDED BY MANUFACTURER.

MAKE BYPASS VALVE DISCHARGE PIPE THE SAME SIZE AS D2 FOR THE LARGEST PRV.

PROVIDE NECESSARY UNIONS FOR THE REMOVAL OF VALVE WITH SCREWED

CONNECTIONS.

SIPHON (TYP.)

VENT TO ATMOSPHERE

PILOT CONTROL LINE

REDUCER (TYP.)

IF REQUIRED.

NOTE 1

D1

N.C.

D2

D2

NOTE 1

NOTE 3

INVERTER

BUCKET TRAP

ASSEMBLY

TYP.

PSV

V

20 D2 MIN.

4 D2 MIN.

10 D1 MIN.

D

PROVIDE UNION UNLESS SAFETY

VALVE HAS FLANGED OUTLET

SAFETY VALVE

OPEN DRAIN (NOTE 3)

CONNECTION TO PRESSURE

VESSEL OR PIPE

VENT PIPE THROUGH ROOF

SUPPORT AS INDICATED ON

DWGS. (NOTES 1, 2)

PIPE THREADED INTO ELBOW

(SAME SIZE AS ELBOW)

DRIP PAN ELBOW

(SECTIONAL VIEW)

3/4" [20mm] DRAIN TO

FLOOR DRAIN OR OPEN

SIGHT DRAIN (NOTE 4)

[2 m m

[610mm]

[76mm]

ELEVATION

FLEXIBLE

CONNECTOR

NOTES:

1.

2.

3.

4.

UNLESS OTHERWISE SHOWN ON THE DRAWINGS, SIZE THE VENT PIPE SO THAT STEAM IS NOT

BLOWN OUT AT THE VENT PIPE ENTRANCE. UTILIZE THE CALCULATION METHOD CONTAINED IN

ANSI B31.1. POWER PIPING CODE, APPENDIX II.

VENT PIPE SHALL TERMINATE 6' [1829mm] MIN. ABOVE FINISHED ROOF.

DISCHARGE OF DRAIN MUST BE DIRECTED AWAY FROM PLATFORMS OR OTHER AREAS WHICH

PERSONNEL MAY OCCUPY.

DO NOT CONNECT ANY OTHER DRAIN TO THE DRIP PAN ELBOW DRAIN PIPE.

3"

24" MAX.

M

IN

STEAM TRAP ASSEMBLY

STEAM LINE DRIP POCKET

STEAM LINE

(TYPICAL)

3/4" [20mm] DRAIN (ALTERNATE

LOCATIONS) (TYPICAL)

FROM DRIP

CONNECTION

CAP (TYPICAL)

3/4" [20mm] MIN.

[1 m m

M

IN

DRIP LEG (TYP.)

[3 m m

M

IN

NOTE:

DRIP POCKET PIPE SIZE SAME

AS STEAM MAIN UNLESS

OTHERWISE NOTED.

3/8" [10mm] TEST

CONNECTION

DRIP

RETURN

PIPE T0 STEAM

TRAP (TYPICAL)

[1 m m

M

IN

[3 m m

M

1" V

1" FILL LINE

EXHAUST LINE

RESERVOIR

INLET LIFT

CHECK VALVE

1" VENT TO

ATMOSPHERE

LPR FROM

SYSTEM

UNION

(TYP.)

TRAP

STEAM

3/4" HPS

TO FD

1/2"

3/4"

1/2"

TO FD

OUTLET LIFT

CHECK VALVE

RELIEF VALVE

SET @ 125 PSI

PUMP

DISCHARGE

PC

SHUT-OFF VALVE

(TYP), SEE SPEC

FOR TYPE

T

STRAINER WITH

BLOWDOWN VALVE,

NIPPLE, AND CAP

PRESSURE

GAGE WITH

COCK

SPCP-1

GAGE GLASS

SPCP-2

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

CONSTRUCTION BID

DOCUMENTS

FULLY SPRINKLERED

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

PRIME CONSULTANT STAMPCONSULTANT

321 4 5 6 7 8 9 10

636-18-304

X

CONSTRUCT COMBINED

ENERGY PLANT PHASE 1

5350 W 94TH TERRACE #102

PRAIRIE VILLAGE, KS 66207

T 913.258.5026 www.rossbar.com

4101 WOOLWORTH AVE

OMAHA, NE 68105

11/30/2021

NOT F

OR

CONSTRUCTIO

N

D U s e rs

\m s im m o n s \D o c u m e n ts

\2 -1

M

E C

H v m s im m o n s L W

R W

.r v t

/5

/2

:5 :5

P

M

0-M-502

MECHANICAL DETAILS

JES MDS

NOT TO SCALE

END OF STEAM LINE DRIP TRAP

NOT TO SCALE

HIGH AND MEDIUM PRESSURE STEAM

TRAP DISCHARGE INTO PUMPED

CONDENSATE RETURN LINE

NOT TO SCALE

STEAM FLOW METER PRIMARY ELEMENT

AND FLOW TRANSMITTER INSTALLATION

NOT TO SCALE

STEAM METER

NOT TO SCALE

STEAM PRESSURE REDUCING STATION -

DOUBLE VALVE

NOT TO SCALE

STEAM SAFETY VALVE

NOT TO SCALE

STEAM TRAP ASSEMBLY AND STEAM LINE

DRIP POCKET

Revisions: Date:

ADDENDUM NO. 01 04/07/2022

NOT TO SCALE

STEAM POWERED CONDENSATE PUMP

(SPCP) DETAIL

P & T TEST PLUG; INSTALL AT

SAME ELEVATION

PIPING SHOWN IS TYPICAL FOR EACH CELL.

ALL OUTDOOR PIPING SHALL BE HEAT TRACED

AND INSULATED PERS ECTION 230700, EXCEPT

OMIT FOR OVERFLOW LINE AND DRAIN

DOWNSTREAM OF SHUTOFF VALVE. OMIT

INSULATION ON BURIED PIPE. OMIT HEAT

TRACE ON PIPE BURIED BELOW FROST LINE.

CR MAIN

SEE PLANS

SLOPE 3% DOWN

CS MAIN

SEE PLANS

TO DRAIN D

SHUT-OFF VALVE

(TYP), SEE SPEC

FOR TYPE

CS

CR

DRAIN

UNION (TYP.)

3" OVERFLOW

NOTE:

EQUALIZATION PIPING OR FLUME TO ADJACENT

CELL TO INTERCONNECT COLD WATER BASINS.

SIZE PER MANUFACTURERS RECOMMENDATIONS.

FLEXIBLE CONNECTION (TYP).

REFER TO SPECIFICATIONS

1/2" [15mm]

PUMP

FLOOR

PRESSURE GAGE

1/2" [15mm]

DRAIN

OPTIONAL STRAINER

FIRST 3 HANGERS FOR EACH PIPE AND

BRANCH SHALL BE SPRING & NEOPRENE

TYPE. TYPE "H" FOR 4" [100mm] DIA. PIPE

& SMALLER. TYPE "H-P" FOR 5" [125mm]

DIA. PIPE & LARGER.

RIGID PIPE

HANGER

INSTALL HANGER AS CLOSE TO

PIPE ELBOW AS POSSIBLE

(TYPICAL)

MECHANICAL COUPLING

(6" MIN.[150 MM] SPACING)

(TYPICAL)

SUCTION DIFFUSER

WITH BUILT IN STRAINER.

OPTIONAL: LONG RADIUS

ELBOW AND INLET

STRAINER WITH 3XDIAM

STRAIGHT INLET TO PUMP

1" [25mm] MIN. DIA.

PIPE STAND

CONCRETE BASE

(SEE DETAIL)

BUTTERFLY OR BALL

SHUT OFF VALVE, TYP.

RIGID PIPE

HANGER

NOTES:

SEE SPECIFICATION SECTION "PUMPS" FOR Y STRAINER OPTION

FLANGED

CONNECTION

1/4"x1 1/4"

[6.4x31.4mm]

IRON PIPE

CLAMP

1/4"x1 1/4"

[6.4x31.4mm] IRON

PIPE STRAP

[1 m m

HIGH DENSITY

POLYETHYLENE (HDPE)

SLEEVE WITH INTEGRAL

HOLLOW MOLDED WATER

STOP RING 4" [100mm]

LARGER THAN OUTSIDE

DIAMETER OF PIPE

5/8" [16mm]Ø ROD

PIPE SLEEVE

WATER STOP

EXTERIOR WALL

PIPEPIPE SLEEVE

WHERE SPECIFIED

FIRE-STOPPING

MATERIAL

BOLT

RISER

CLAMP

PIPE SLEEVE

WHERE

SPECIFIED

RISER

CLAMP

INSULATION

ELEVATION

RISER

PLAN

RISER CLAMP.

BOTTOM CLAMP

REQUIRED AT

ANCHOR POINTS

ONLY.

PROVIDE ANCHORS ONLY

WHERE SHOWN ON

DRAWINGS.

EXTEND SLEEVE ABOVE

FLOOR WHERE SPECIFIED.

BOLT

(TYPICAL)

FLOOR

SLAB

NOTES:

1.

2.

NOTE:

1. MAINTAIN UPSTREAM AND DOWN STREAM DISTANCES RECOMMENDED BY METER MANUFACTURES

TE

TEMPERATURE ELEMENT

INTERFACE WITH

METERING

STATION

TEFE

SUPPLY

OUTLET

FLOW ELEMENT

BACNET

INTERFACE

EXTERIOR WALL

ROOF

GROUND

SUPPORT VENT PIPING

PER SPECIFICATIONS

DRIP LEG LENGTH

L (IN.) = (294.1) / (INSIDE Ø (IN.))²

REMOVABLE CAP TO BE

INSTALLED UPSTREAM

OF FLEX CONNECTION

CHILLER RUPTURE DISK

FLEX CONNECTION

PER SPECIFICATIONS

VENT LINE FROM PURGE

DISCHARGE

MINIMUM DISTANCES:

15' ABOVE GROUND LEVEL

20' FROM ALL BUILDING OPENINGS

1/4 IN. FL X 1/4 IN. NPT

THREADED END FOR

HOSE CONNECTION

36" MIN

TERMINATE PIPING WITH 3/16" MESH

BRASS OR STAINLESS HARDWARE

CLOTH

3/4" HOSE-END

DRAIN VALVE W/CAP

(TYP)

SHUT-OFF VALVE (TYP),

SEE SPEC FOR TYPE

PRESSURE

GAUGE (TYP)

TO FLOOR DRAIN

SAFETY RELIEF VALVE

AUTOMATIC AIR VENT

THERMOMETER (TYP)

GAUGE COCK (TYP)

FLEXIBLE CONNECTOR (TYP),

SEE SPECIFICATIONS

CONDENSATION TRAP

A

RV

CR

ROOF

CWR

CS

CWS

NOTES:

PROVIDE AIR VENTS AND DRAIN

VALVES AT ALL SUCH POINTS

PROVIDED BY CHILLER

MANUFACTURER, BOTH WATER BOXES,

BOTH ENDS, TYPICAL.

ALTERNATE LOCATION OF

CWS (3-PASS CHILLERS)

PROVIDE OFFSET IN PIPING

TO CLEAR WATER BOX (TYP)

SEE

PLANS

FOR PIPE

SIZE AND

ROUTE

PURGE VENT

(BY CHILLER MFR)

CALIBRATED BALANCING

VALVE

1.

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

CONSTRUCTION BID

DOCUMENTS

FULLY SPRINKLERED

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

PRIME CONSULTANT STAMPCONSULTANT

321 4 5 6 7 8 9 10

636-18-304

X

CONSTRUCT COMBINED

ENERGY PLANT PHASE 1

5350 W 94TH TERRACE #102

PRAIRIE VILLAGE, KS 66207

T 913.258.5026 www.rossbar.com

4101 WOOLWORTH AVE

OMAHA, NE 68105

11/30/2021

NOT F

OR

CONSTRUCTIO

N

D U s e rs

\m s im m o n s \D o c u m e n ts

\2 -1

M

E C

H v m s im m o n s L W

R W

.r v t

/5

/2

:5 :5

P

M

0-M-503

MECHANICAL DETAILS

JES MDS

NOT TO SCALE

COOLING TOWER WITH BOTTOM SUMP

OUTLET AND INTERNAL PIPING DETAIL

NOT TO SCALE

SINGLE SUCTION FLOOR MOUNTED PUMPS

- CONNECTIONS WITH MECHANICAL

COUPLINGS

NOT TO SCALE

SUPPORT ANCHOR (CONDENSATE OR

CHILLED WATER)

NOT TO SCALE

SUPPORT ANCHOR FOR PIPE RISER

NOT TO SCALE

WATERFLOW MEASURING DEVICE

NOT TO SCALE

CHILLER REFRIGERANT VENT PIPING

DETAIL

Revisions: Date:

ADDENDUM NO. 01 04/07/2022

NOT TO SCALE

WATER COOLED CHILLER PIPING DETAIL

6 UNIT SHALL REMOVE 80% OF THE 30 MICRON PARTICLES IN 100 CIRCULATIONS. UNIT SHALL BE CAPABLE OF 5 MICRON PARTICLE SIZE REMOVAL.

NOTES:

1 PROVIDE COALESCING TYPE SEPARATOR. CENTRIFUGAL TYPE NOT ACCEPTED.

2 VESSEL SHALL BE CERTIFIED FOR 150 LB WORKING PRESSURE AND SHALL BE FURNISHED WITH ANSI / ASME B16.5 OR B16.47 CLASS 150 STEEL WELD NECK RAISED-FACE FLANGES.

3 UNIT SHALL INCLUDE STRUCTURED COALESCING MEDIA FILLING THE ENTIRE VESSEL.

4 VESSELS WITH LOOSE OR PARTIALLY FILLED INTERNAL MEDIA NOT ACCEPTED.

5 UNIT SHALL REMOVE 100% OF FREE AND ENTRAINED AIR AND 99.6% OF DISSOLVED AIR AS TESTED BY INDEPENDENT LAB.

AIR-DIRT SEPARATOR SCHEDULE

IN GPM FT IN IN IN IN LBS

ADS-1 CHILLER ROOM CAMPUS CHILLED WATER LOOP SPIROTHERM VDN-2400FA COALESCING 24 6000 5 2 72 48 158 7240 1-6

ADS-2 CHILLER ROOM BLDG HEATING HOT WATER SPIROTHERM VDN-400FA COALESCING 4 400 5 1 21 9 31 233 1-6

MARK LOCATION SERVICE MANUFACTURERS MODEL TYPE

CONN. MAX MAX DRAIN PHYSICAL DATA

NOTESSIZE FLOW P.D. SIZE L W H WEIGHT

1 EQUIPMENT PERFORMANCE VALUES SELECTED FOR OPERATION AT AN ELEVATION OF 1100 FT ABOVE SEA LEVEL.

2 PROVIDE CONCRETE HOUSEKEEPING PAD PER SPECIFICATIONS. COORDINATE HOUSEKEEPING PAD WITH ARCHITECTURAL.

3 VARIABLE FREQUENCY DRIVE FURNISHED BY DIVISION 23 CONTRACTOR AND INSTALLED BY DIVISION 26

4 PUMP MOTOR SHALL BE NON-OVERLOADING THROUGHOUT THE FULL RANGE OF THE PUMP CURVE.

5 NPSHA IS THE NET POSITIVE SUCTION HEAD AVAILABLE TO THE PUMP. PUMP AT DESIGN CONDITIONS SHALL HAVE NPSH LESS THAN SPECIFIED VALUE.

PUMP SCHEDULE

NOTES:

CTP-1 CHILLER PLANT CONDENSER WATER SUPPLY BELL AND GOSSETT VSX 12 10 VERTICAL SPLIT-CASE BASE 4,500 70 25.7 125 94.5 1674 2885 VFD VFD 460/3 1-5

CTP-2 CHILLER PLANT CONDENSER WATER SUPPLY BELL AND GOSSETT VSX 12 10 VERTICAL SPLIT-CASE BASE 4,500 70 25.7 125 94.5 1674 2885 VFD VFD 460/3 1-5

CTP-3 CHILLER PLANT CONDENSER WATER SUPPLY BELL AND GOSSETT VSX 12 10 VERTICAL SPLIT-CASE BASE 4,500 70 25.7 125 94.5 1674 2885 VFD VFD 460/3 1-5

HWP-1 CHILLER PLANT BUILDING XX HEATING HOT WATER BELL AND GOSSETT e-80 3 3 VERTICAL INLINE INLINE 200 60 5.2 7.50 3.92 1800 280 VFD VFD 460/3 1-5

HWP-2 CHILLER PLANT BUILDING XX HEATING HOT WATER BELL AND GOSSETT e-80 3 3 VERTICAL INLINE INLINE 200 60 5.2 7.50 3.92 1800 280 VFD VFD 460/3 1-5

CWP-1 CHILLER PLANT PRIMARY CHILLED WATER RETURN BELL AND GOSSETT VSX 8 6 VERTICAL SPLIT-CASE BASE 2,000 130 16.9 100 75.9 1670 2104 VFD VFD 460/3 1-5

CWP-2 CHILLER PLANT PRIMARY CHILLED WATER RETURN BELL AND GOSSETT VSX 8 6 VERTICAL SPLIT-CASE BASE 2,000 130 16.9 100 75.9 1670 2104 VFD VFD 460/3 1-5

CWP-3 CHILLER PLANT PRIMARY CHILLED WATER RETURN BELL AND GOSSETT VSX 8 6 VERTICAL SPLIT-CASE BASE 2,000 130 16.9 100 75.9 1670 2104 VFD VFD 460/3 1-5

MARK LOCATION SERVICE MANUFACTURERS MODEL MIN. SIZE TYPE MOUNTING MAX. FLOW/HEAD NPSHA MOTOR WEIGHT ELECTRICAL NOTES

SUCTION DISCHARGE DISC. STARTER V/PH

IN. IN. GPM FTHD FT HP BHP RPM LBS TYPE TYPE

1 EQUIPMENT PERFORMANCE VALUES SELECTED FOR OPERATION AT AN ELEVATION OF 1100 FT ABOVE SEA LEVEL.

2 VARIABLE FREQUENCY DRIVE FURNISHED BY DIVISION 23 CONTRACTOR, INSTALLED BY DIVISION 26 CONTRACTOR.

3 PROVIDE SIDE OUTLET SUMP.

4 COORDINATE SIZE OF CONDUCTOR TERMINATION LUGS WITH CONDUCTOR SIZES SHOWN ON ELECTRICAL DRAWINGS.

5 PROVIDE WITH WELDED STAINLESS STEEL BASIN.

6 UNIT SHALL BE FACTORY FABRICATED AND FACTORY TESTED.

7 PROVIDE LADDER, GUARD RAIL, AND DAVIT FOR SERVICE AT THE TOP OF EACH UNIT

8 PROVIDE STANDARD MANUFACTURER CONTROL DEVICES FOR BASIN WATER LEVEL

9 PROVIDE COOLING TOWER WITH 18KW BASIN HEATER FOR FREEZE PROTECTION WITH CONTROLLER.

COOLING TOWER SCHEDULE

NOTES:

KW EA. QTY QTY HP/FAN RPM TYPE TYPE

CT-1 CHILLER PLANT ROOF CHILLER CONDENSER WATER MARLEY NC8407TAN2 22,421 4500 3750 75.0 89.9 95.0 85.0 Y 48,830 24 2 2 40.00 1800 VFD VFD 460/3 1-9

CT-2 CHILLER PLANT ROOF CHILLER CONDENSER WATER MARLEY NC8407TAN2 22,421 4500 3750 75.0 89.9 95.0 85.0 Y 48,830 24 2 2 40.00 1800 VFD VFD 460/3 1-9

MARK LOCATION SERVICE MANUFACTURERS MODEL CAP.

MBH

MAX

FLOW

GPM

DESIGN

FLOW

GPM

EAT

°F WB

LAT

°F WB

EWT

°F

LWT

°F

VFD

Y/N

WEIGHT

LBS

BASIN HEATER FAN ELECTRICAL

NOTES

FAN MOTOR DISC. STARTER V/PH

7 NOTE: CHILLER INITIAL FLOW RATE WILL OPERATE AT 10F TEMPERATURE DIFFERENTIAL (TD) TO OPERATE WITH EXISTING COILS. FINAL WILL BE 15 DEGREE TD FOLLOWING FUTURE CAMPUS HVAC UPGRADE.

8 PROVIDE REFRIGERANT DIFFERENTIAL PRESSURE HEAD CONTROL FOR OPERATION WITH WATERSIDE ECONOMIZER AND FUNCTIONAL PERFORMANCE TESTING AT LOW OR NO LOAD ON EQUIPMENT STARTUP.

VV: VA PROVIDED / VA INSTALLED

VC: VA PROVIDED / CONTRACTOR INSTALLED

6 VARIABLE FREQUENCY DRIVE FURNISHED UNIT MOUNTED WITH CHILLER BY MANUFACTURER.

1 EQUIPMENT PERFORMANCE VALUES SELECTED FOR OPERATION AT 15 DEGREE EVAPORATOR DESIGN CONDITION AT AN ELEVATION OF 1100 FT ABOVE SEA LEVEL.

2 AS DEFINED BY AHRI 550/590 - PERFORMANCE RATINGS OF WATER-CHILLING PACKAGES USING THE VAPOR COMRESSION CYCLE.

3 SOUND PRESSURE MEASURED IN ACCORDANCE WITH ANSI/AHRI STANDARD 575-1994 (A-WEIGHTED).

4 REFRIGERANT SHALL BE AS APPROVED PER CURRENT ASHRAE 15-2019.

5 PROVIDED BY / INSTALLED BY ABBREVIATIONS INDICATE THE FOLLOWING:

CC: CONTRACTOR PROVIDED / CONTRACTOR INSTALLED

CHILLER SCHEDULE (WATER COOLED)

NOTES:

WCC-1 CC BLDG XX CHILLER PLANT SITE CHILLED WATER DEMAND TRANE CVHH 1,250 0.554 0.367 R-1233zd 2 3,000 790 42 52 15.0 2000 770.00 42 57 10 2 3,750 85 95 20 58,000 1600 1093 Y VFD VFD 460/3 1-7

WCC-2 CC BLDG XX CHILLER PLANT SITE CHILLED WATER DEMAND TRANE CVHH 1,250 0.554 0.367 R-1233zd 2 3,000 790 42 52 15.0 2000 770.00 42 57 10 2 3,750 85 95 20 58,000 1600 1093 Y VFD VFD 460/3 1-7

MARK

PROVIDED BY /

INSTALLED BY

LOCATION SERVICE MANUFACTURERS MODEL

CAP

(TONS)

MAX

KW/TON

MAX

NPLV

REFR.

TYPE

EVAPORATOR (DESIGN PERFORMANCE) EVAPORATOR (OPERATING CONDITIONS) CONDENSER (DESIGN PERFORMANCE) ELECTRICAL

NOTES

PASS

DESIGN MIN. EWT LWT MAX PD OPERATING MIN. EWT LWT MAX PD PASS DESIGN EWT LWT MAX PD WEIGHT

MOCP MCA

VFD DISC. STARTER V/PH

GPM GPA °F °F FT GPM GPM °F °F FT GPM °F °F FT LBS Y/N TYPE TYPE

CH-E CH-1&2 2019 R123 SITE MODULAR CHILLER PLANT- EAST SIDE AMBULATORY CARE CENTER (ACC) TRANE CVHE0400 - CENTRIFUGAL 600 1,024 1,500 2,3

4 DEMOLISH CHILLER. SEE SHEET 17-MPD100 FOR RELATED INFORMATION.

1 CHILLED WATER CONDITIONS: EWT= 52F, LWT-42F (10F TEMPERATURE DIFFERENTIAL)

2 CHILLED WATER CONDITIONS: EWT= 56F, LWT-42F (14F TEMPERATURE DIFFERENTIAL)

3 CHILLER IS EXISTING TO REMAIN FOR REFERENCE ONLY.

EXISTING CHILLER SCHEDULE

NOTES:

DESIGN INSTALL REFRIGERANT CAPACITY CHW CW NOTES

MARK MARK YEAR TYPE LOCATION SERVES MAKE MODEL SERIAL NO. TYPE TONS GPM GPM

CH-A CH-1 1999 Lithium Bromide B-17 BASEMENT MECHANICAL ROOM MAIN CHW LOOP TRANE ABTF950 L99F02719M ABSORPTION 980 2,352 3,400 1,4

CH-B CH-1 2012 R123 B-17 TEMPORARY OUTDOOR ENCLOSURE MAIN CHW LOOP TRANE CVHF1300 L11M04637 CENTRIFUGAL 1,250 1,870 2,500 1,3

CH-C Existing 1998 HFC-134A B-1 ROOM B024A SURGERY/SPD/WAREHOUSE MCQUAY PEH087K 58C81053 CENTRIFUGAL 450 1,080 2,500 1,3

CH-D CH-1 2014 R410 B-1 ROOM B024A SURGERY/SPD/WAREHOUSE MultiStack M9070XC5A-1W2AAC-410A AE-11-080 MODULAR 450 1,080 1,350 1,3

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

CONSTRUCTION BID

DOCUMENTS

FULLY SPRINKLERED

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

PRIME CONSULTANT STAMPCONSULTANT

321 4 5 6 7 8 9 10

636-18-304

X

CONSTRUCT COMBINED

ENERGY PLANT PHASE 1

5350 W 94TH TERRACE #102

PRAIRIE VILLAGE, KS 66207

T 913.258.5026 www.rossbar.com

4101 WOOLWORTH AVE

OMAHA, NE 68105

11/30/2021

NOT F

OR

CONSTRUCTIO

N

D U s e rs

\m s im m o n s \D o c u m e n ts

\2 -1

M

E C

H v m s im m o n s L W

R W

.r v t

/6

/2

:4

:4

A

M

0-M-601

MECHANICAL SCHEDULES

JES MDS

24 22 AQUATHERM SDR 17.6 PP-RT

18 15.8 AQUATHERM SDR 17.6 PP-RT

NOMINAL SIZE ID (IN) MANUFACTURER WGT MATERIAL

UNDERGROUND PIPE SCHEDULE

Revisions: Date:

ADDENDUM NO. 01 04/07/2022

1 PROVIDE COOLING CAPACITY SCHEDULED AT 100F AMBIENT AIR TEMPERATURE

2 DISCONNECT PROVIDED WITH THE EQUIPMENT BY MANUFACTURER.

3 INDOOR FAN COIL POWERED FROM OUTDOOR CONDENSING UNIT.

7 PROVIDE CONDENSATE PUMP AND OVERFLOW SHUTOFF SWITCH WITH UNIT.

8 PROVIDE STANDARD FACTORY FURNISHED WASHABLE FILTERS.

4 TEMPERATURE CONTROL - PROVIDE COMMUNICATING WALL THERMOSTAT INTERFACE FOR COMMUNICATION WITH BAS.

5 PROVIDE NECESSARY MOUNTING BRACKET AND ACCESSORIES FOR SPECIFIED MOUNTING.

6 PROVIDE ALL MOUNTING HARDWARE REQUIRED FOR UNIT TYPE SUBJECT TO MANUFACTURERS INSTALLATION INSTRUCTIONS.

DUCTLESS SPLIT SYSTEM FAN COIL UNIT SCHEDULE

NOTES:

MARK LOCATION SERVICE MANUFACTURER MODEL MOUNTING COOLING NOTES

REFR. CFM NOMINAL TH SH EAT LAT WEIGHT MCA V/PH

TYPE TONS MBH MBH DB WB DB WB LBS

ACU-1 EMERGENCY ELECTRICAL RM EMERGENCY ELECTRICAL RM MITSUBISHI PKA-A24KA7 WALL R410A 750 2 22.5 20.3 80.0 67.0 55.0 54.2 37 1 208/1 1-8

ACU-2 IT ROOM IT ROOM MITSUBISHI PKA-A24KA7 WALL R410A 750 2 22.5 20.3 80.0 67.0 55.0 54.2 37 1 208/1 1-8

ACU-3 CONTROL ROOM CONTROL ROOM MITSUBISHI PKA-A24KA7 WALL R410A 750 2 22.5 20.3 80.0 67.0 55.0 54.2 37 1 208/1 1-8

NOTES:

1 125 PSI MAXIMUM WORKING PRESSURE.

2 HEAT EXCHANGERS PROVIDED WITH HOT WATER PUMPS AND ASSOCIATED EQUIPMENT AS PART OF A PRE-MANUFACTURERED STEAM TO HOT WATER SKID ASSEMBLY.

3 SIZE STEAM TRAP FOR A SAFETY FACTOR OF 2:1 AT OPERATING 1/2 MAXIMUM PRESSURE DIFFERENTIAL.

FLUID FLOW CAP. EWT LWT WPD MAX. NO. FLUID CAP. INLET PRESS. MIN. HEATING

TYPE GPM MBH °F °F FT PASSES TYPE MBH PSI SURFACE (SF)

HEAT EXCHANGER SCHEDULE (STEAM)

HX-1 CHILLER PLANT CHILLER PLANT HHW LOOP ARMSTRONG WS-0802-200E SHELL & TUBE 40 12 WATER 160 1571 140 160 12 2 STEAM 1571 30 14.3 1-3

HX-2 CHILLER PLANT CHILLER PLANT HHW LOOP ARMSTRONG WS-0802-200E SHELL & TUBE 40 12 WATER 160 1571 160 180 12 2 STEAM 1571 30 14.30 1-3

MARK LOCATION SERVICE MANUFACTURERS MODEL TYPE

LENGTH

(IN)

DIA.

(IN)

TUBE SIDE SHELL SIDE

NOTES

3 PROVIDE WITH BIRDSCREEN AND MOTORIZED BACKDRAFT DAMPER.

1 PROVIDE WITH MINIMUM 24" HIGH ROOF CURB, BIRDSCREEN AND BACKDRAFT DAMPER.

2 DIVISION 26 CONTRACTOR TO FURNISH AND INSTALL DISCONNECT SWITCH AND MOTOR STARTER.

EF-3 SIDEWALL EA ELECTRICAL ROOM GREENHECK SIDEWALL CUE-160-A 3780 0.75 DIRECT 2 1725 N 460/3 2, 3

FAN SCHEDULE

NOTES

EF-1 ROOF EA MECHANICAL ROOM GREENHECK ROOF G-240-VG 7100 1 DIRECT 5 1020 N 460/3 1, 2

EF-2 ROOF EA STAFF TOILET GREENHECK ROOF CUE-099-1 150 0.65 DIRECT 0.25 1433 N 120/1 1, 2

MARK LOCATION

SERVICE

MANUFACTURER MOUNTING MODEL CFM

ESP DRIVE MIN. FAN VFD ELECTRICAL

NOTES

TYPE LOCATION (IN) (BELT/DIRECT) HP RPM (Y/N) V/PH

LOUVER SCHEDULE

LU-1 CHILLER MEZZANINE AHU-1 RUSKIN L375D 106x80 16850 32.83 550 0.03

LU-2 CHILLER MEZZANINE AHU-2 RUSKIN L375D 60x50 3780 10.41 500 0.03

MARK LOCATION SERVICE MANUFACTURERS MODEL

SIZE

(W" x H")

CFM

MIN. FREE AREA

(SF)

FREE AREA

MAX. VEL.

(FPM)

MAX. P.D.

(IN. W.C.)

NOTES

NOTES:

1 PROVIDE UNIT WITH FACTORY SUPPLIED NEMA 1 MOTOR STARTER ENCLOSURE WITH SAFETY DISCONNECT AND H.O.A. SWITCH.

COOLING TOWER FILTRATION SCHEDULE

GPM FT IN. IN. GPM

CTF-1 90 150 AMIAD ASY-850PGM LH-S 850 35 6 6 850 35 15 460/3 1

CTF-2 90 150 AMIAD ASY-850PGM LH-S 850 35 6 6 850 35 15 460/3 1

MANUFACTURER MODEL

FLOW PRESS. SIZE FLOW

HEAD

FTHD

MOTOR HP

ELECTRICAL V

/ PH

RATE DROP INLET OUTLET RATE

SYSTEM

SYSTEM OPERATING

TEMP. °F

SYSTEM WORKING

PRESSURE PSIG

WATER FILTRATION UNIT PUMP

NOTES

THE ASSOCIATED REFRIGERANT TRAPS BASED ON THE ACTUAL ROUTING AND PROVIDE OTHER APPURTENANCES TO PROVIDE A FULLY FUNCTIONAL AND OPERATIONAL SYSTEM.

3 COORDINATE WITH THE MANUFACTURER LOCATIONS FOR ALL REFRIGERANT PIPING DEVICES TO MAINTAIN SERVICEABILITY AND ACCESSIBILITY.

4 PROVIDE LIQUID LINE FILTER DRYER AND SIGHT GLASS.

1 EQUIPMENT SIZED FOR 95°F AMBIENT TEMPERATURE.

2 COORDINATE WITH THE MANUFACTURER THE HORIZONTAL AND VERTICAL REFRIGERANT PIPE ROUTING TO DETERMINE PIPE SIZES FOR THE REFRIGERANT PIPING. MANUFACTURER

SHALL PROVIDE DETAILED REFRIGERANT PIPING DIAGRAMS INCLUDING DIMENSIONAL DATA FOR ALL REFRIGERANT PIPING DEVICES. THE MANUFACTURER SHALL SIZE AND LOCATE

8 PROVIDE CONDENSER COIL HAIL GUARDS.

9 PROVIDE HARD START KIT.

10 INDOOR FAN COIL POWERED FROM OUTDOOR CONDENSING UNIT

5 UNIT TO MOUNT ON ROOF MOUNTED BASE RAILS. SEE ARCHITECTURAL DRAWINGS FOR MORE INFORMATION.

6 DISCONNECT FURNISHED AND INSTALLED BY DIVISION 26 CONTRACTOR.

7 STARTERS FOR ALL MOTORS SHALL BE FURNISHED INTEGRAL WITH UNIT.

CONDENSING UNIT SCHEDULE

NOTES:

TYPE TYPE

CU-1 ROOF ACU-1 MITSUBISHI PUZ-A24NHA7 410A 24.0 21.40 4.35 180 19 26 NOTE 6 NOTE 7 208/1 1-10

CU-2 ROOF ACU-2 MITSUBISHI PUZ-A24NHA7 410A 24.0 21.40 4.35 180 19 26 NOTE 6 NOTE 7 208/1 1-10

MARK LOCATION SERVICE MANUFACTURERS MODEL

REFR. CAP. SEER COP WEIGHT ELECTRICAL

NOTESTYPE MBH @ 47°F LBS MCA MOCP DISC.

STARTER

V/PH

CU-3 ROOF ACU-3 MITSUBISHI PUZ-A24NHA7 410A 24.0 21.40 4.35 180 19 26 NOTE 6 NOTE 7 208/1 1-10

2 VARIABLE FREQUENCY DRIVES TO BE FACTORY INSTALLED SINGLE VFD PER FAN.

3 SPECIFIED FAN ESP ACCOUNTS FOR DUCT LOSSES EXTERNAL TO UNIT.

4 DIVISION 26 CONTRACTOR SHALL PROVIDE SMOKE DETECTORS IN RETURN AIR AND SUPPLY AIR DUCT(S).

5 PROVIDE CONCRETE HOUSEKEEPING PAD PER SPECIFICATIONS.

6 PROVIDE SHAFT GROUNDING SYSTEM ON MOTORS. REFER TO MOTOR SPECIFICATION FOR ADDITIONAL INFORMATION.

7 MIN. O/A IS THE MINIMUM OUTSIDE AIR CFM USING VENTILATION RESET OR DEMAND CONTROL VENTILATION.

8 PROVIDE UNIT WITH ECONOMIZER.

9 PROVIDE UNIT WITH BOTTOM DISCHARGE AND RETURN.

10 DISCONNECT SWITCH FURNISHED AND INSTALLED BY DIVISION 26 CONTRACTOR.

75 62 55 54.7 87 82 42 55 13 1.13 0.25 450 1 8 8 0.0 85.0 11 4 0.1 501 160 140 35 1.2 8 2 62 38 145 1686 VFD 460/3 5 1-9

AIR HANDLING UNIT SCHEDULE (CHILLED WATER / HOT WATER) - CONTINUED

NOTES:

1 PROVIDE FACTORY MOUNTED DISCONNECT INSTALLED ON SERVICE SIDE OF UNIT.

AIR TEMP. AIR TEMP. TOTAL SENS. ENT. LVG. FLOW WPD APD VEL. COIL FINS AIR TEMP. FINS MAX APD VEL. ENT. LVG. FLOW WPD

FT

W H L MAX. DISC. SCCR

EDB F EWB F LDB F LWB F MBH MBH EWT F LWT F GPM FT IN FPM QTY FPI EDB F LDB F FPI ROWS IN FPM EWT F LWT F GPM MERV IN IN IN IN LBS TYPE (kA)

87 72 55 54.7 957 582 42 55 147 11.30 0.53 450 1 8 8 0.0 85.0 11 4 0.1 501 160 140 155 5.7 8 2 113 68 174 5436 VFD 460/3 5 2-8, 10

COOLING COIL HEATING COIL FILTER DIMENSIONS WEIGHT ELECTRICAL

NOTES

CC ENTERING CC LEAVING CC CAPACITY CC FLUID COIL MAX. CC MAX

MAX

ROWS

HC ENTERING MAX COIL MAX. HC FLUID PRE-FILTER MAX. MAX. MAX.

V/PH

5 PROVIDE CONCRETE HOUSEKEEPING PAD PER SPECIFICATIONS.

6 PROVIDE SHAFT GROUNDING SYSTEM ON MOTORS. REFER TO MOTOR SPECIFICATION FOR ADDITIONAL INFORMATION.

7 MIN. O/A IS THE MINIMUM OUTSIDE AIR CFM USING VENTILATION RESET OR DEMAND CONTROL VENTILATION.

2 VARIABLE FREQUENCY DRIVES TO BE FACTORY INSTALLED SINGLE VFD PER FAN.

3 SPECIFIED FAN ESP ACCOUNTS FOR DUCT LOSSES EXTERNAL TO UNIT.

4 DIVISION 26 CONTRACTOR SHALL PROVIDE SMOKE DETECTORS IN RETURN AIR AND SUPPLY AIR DUCT(S).

8 PROVIDE UNIT WITH MINIMUM OUTSIDE AIR AND ECONOMIZER OUTSIDE AIR DAMPER.

9 PROVIDE UNIT WITH BOTTOM DISCHARGE.

10 DISCONNECT SWITCH FURNISHED AND INSTALLED BY DIVISION 26 CONTRACTOR.

AHU-2 CHILLER PLANT MEZZ. ELECTRICAL ROOM TRANE CSAA INDOOR PLENUM FAN ARRAY 2 3780 3780 3780 160 2040 2040 80 1.00 2.26 400.00 2.32 2838 1.50 DIRECT Y 3780 1960

AIR HANDLING UNIT SCHEDULE (CHILLED WATER / HOT WATER)

NOTES:

1 PROVIDE FACTORY MOUNTED DISCONNECT INSTALLED ON SERVICE SIDE OF UNIT.

QTY. AIRFLOW SUPPLY MAX OSA MIN OSA SUPPLY MAX OSA MIN OSA ESP TSP VELOCITY HP DRIVE VFD AIRFLOW AIRFLOW

CFM CFM CFM CFM CFM CFM CFM IN IN FPM PER FAN TYPE Y/N CFM CFM

AHU-1 CHILLER PLANT MEZZ. CHILLER PLANT TRANE CSAA INDOOR PLENUM FAN ARRAY 2 16850 16850 16850 10350 9860 9860 7100 2.00 3.68 400.00 14.52 1750 7.50 DIRECT Y 16850 2760

MARK LOCATION SERVES MANUFACTURER MODEL TYPE

SUPPLY FAN RETURN / EXHAUST

FAN TYPE

FAN DESIGN DESIGN AIRFLOW OPERATING AIRFLOW

BHP RPM

MAX. DESIGN OPERATING

VFD-CT-1 VFD-CT-1 CHILLER PLANT ROOF CT-1 FAN DIRECT ABB ACH550 2 40 MULTISTRUT 460/3 460/3 2-5

VFD-CT-2 VFD-CT-2 CHILLER PLANT ROOF CT-2 FAN DIRECT ABB ACH550 2 40 MULTISTRUT 460/3 460/3 2-5

VARIABLE SPEED DRIVE (VFD) SCHEDULE

NOTES:

1 VARIABLE FREQUENCY DRIVES TO BE FACTORY INSTALLED. COORDINATE ALL ELECTRICAL CONNECTIONS WITH DIVISION 26 CONTRACTOR.

2 VARIABLE FREQUENCY DRIVES TO BE FURNISHED AND INSTALLED BY DIVISION 23 CONTRACTOR. COORDINATE ALL ELECTRICAL CONNECTIONS WITH DIVISION 26 CONTRACTOR.

3 VARIABLE FREQUENCY DRIVE OUTPUT TO COINCIDE WITH ASSOCIATED EQUIPMENT REQUIREMENTS PER THEIR SCHEDULED OPERATING VALUES.

4 PROVIDE WITH CLEARANCES PER NEC.

5 REFER TO DETAILS 10/XX-E-501 FOR MORE INFORMATION.

MARK PLAN LOCATION SERVES EQUIPMENT EQUIPMENT MANUFACTURERS MODEL MAX MAX MOUNTING ELECTRICAL NOTES

MARK MOTOR MOTOR

TYPE DRIVE QTY. HP/FAN INPUT V/PH OUTPUT V/PH

VFD-CWP-1 VFD-CWP-1 CHILLER PLANT CWP-1 PUMP DIRECT ABB ACH550 1 100 MULTISTRUT 460/3 460/3 2-5

VFD-CWP-2 VFD-CWP-2 CHILLER PLANT CWP-2 PUMP DIRECT ABB ACH550 1 100 MULTISTRUT 460/3 460/3 2-5

VFD-CWP-3 VFD-CWP-3 CHILLER PLANT CWP-3 PUMP DIRECT ABB ACH550 1 100 MULTISTRUT 460/3 460/3 2-5

VFD-CTP-1 VFD-CTP-1 CHILLER PLANT CTP-1 PUMP DIRECT ABB ACH550 1 125 MULTISTRUT 460/3 460/3 2-5

VFD_AHU-1-SF-1 VFD-SF-1 MEZZANINE AHU-1 PLENUM FAN ARRAY DIRECT ABB ACH550 1 7.5 NOTE 1 460/3 460/3 1,3-4

VFD_AHU-1-SF-2 VFD-SF-2 MEZZANINE AHU-1 PLENUM FAN ARRAY DIRECT ABB ACH550 1 7.5 NOTE 1 460/3 460/3 1,3-4

VFD_AHU-2-SF-3 VFD-SF-3 MEZZANINE AHU-2 PLENUM FAN ARRAY DIRECT ABB ACH550 1 1.5 NOTE 1 460/3 460/3 1,3-4

VFD_AHU-2-SF-4 VFD-SF-4 MEZZANINE AHU-2 PLENUM FAN ARRAY DIRECT ABB ACH550 1 1.5 NOTE 1 460/3 460/3 1,3-4

VFD-CTP-2 VFD-CTP-2 CHILLER PLANT CTP-2 PUMP DIRECT ABB ACH550 1 125 MULTISTRUT 460/3 460/3 2-5

VFD-CTP-3 VFD-CTP-3 CHILLER PLANT CTP-3 PUMP DIRECT ABB ACH550 1 125 MULTISTRUT 460/3 460/3 2-5

VFD-HWP-1 VFD-HWP-1 MEZZANINE HWP-1 PUMP DIRECT ABB ACH550 1 7.5 MULTISTRUT 460/3 460/3 2-5

VFD-HWP-2 VFD-HWP-2 MEZZANINE HWP-2 PUMP DIRECT ABB ACH550 1 7.5 MULTISTRUT 460/3 460/3 2-5

2 FRAME TYPE TO MATCH CEILING CONSTRUCTION, COORDINATE WITH ARCHITECTURAL REFLECTED CEILING PLAN.

3 NECK SIZE SHOWN ON DRAWINGS.

4 4-WAY THROW PATTERN UNLESS OTHERWISE SHOWN ON DRAWINGS.

5 BRANCH DUCT SIZE SHALL BE SAME AS NECK SIZE UNLESS OTHERWISE SHOWN ON DRAWINGS.

6 PROVIDE NECK FOR DUCT CONNECTION.

7 FRONT BLADES PARALLEL TO LONG DIMENSION.

8 FRONT BLADES PARALLEL TO SHORT DIMENSION

9 DOUBLE DEFLECTION BARS SHALL BE ADJUSTABLE.

DIFFUSER , REGISTER AND GRILLE SCHEDULE

NOTES:

1 COORDINATE FINISH WITH ARCHITECTURAL.

MARK MOUNTING SERVICE MANUFACTURERS MODEL TYPE FACE SIZE NECK SIZE MAX. MAX. PRESS. NOTES

LOCATION (IN) (IN) NC DROP IN-WC

E-1 GYPSUM CEILING EXHAUST TITUS 350RL PARALLEL BLADE 12 x 12 10 x 6 30 0.08 1-3, 5-7

E-2 DUCT EXHAUST TITUS 350RL PARALLEL BLADE 18 x 18 18 x 18 30 0.08 1-3, 5-7

S-1 LAY-IN CEILING SUPPLY TITUS OMNI PLAQUE 24 x 24 6" 30 0.1 1-6

S-2 DUCT SUPPLY TITUS 301RL PARALLEL BLADE 12 x 8 12 x 8 30 0.1 1-7

S-3 DUCT SUPPLY TITUS 301RS PARALLEL BLADE 18 x 10 18 x 10 30 0.1 1-6, 8

S-4 DUCT SUPPLY TITUS 111RL PARALLEL BLADE 38 x 36 38 x 36 30 0.1 1-7,9

2 PROVIDE PRECHARGED BLADDER-TYPE ASME RATED TANK.

3 VERTICAL TANKS SHALL BE INSTALLED TO ACCOMMODATE BOTTOM DRAIN CONNECTION.

EXPANSION / COMPRESSION TANK SCHEDULE

NOTES:

1 PROVIDE PRECHARGED DIAPHRAGM-TYPE ASME RATED TANK.

ET-1 MEZZANINE HEATING HOT WATER BELL & GOSSET D-40 FLOOR 21.7 11.6 240 125 263 1,3-4

ET-2 CHILLER PLAN CHILLED WATER BELL & GOSSET B-1200 FLOOR 317 317 240 125 3394 2-4

4 PROVIDE CONCRETE HOUSEKEEPING PAD PER SPECIFICATIONS FOR FLOOR-MOUNTED UNITS.

MARK LOCATION SERVICE MANUFACTURERS MODEL MOUNTING

TANK SIZE

GAL.

ACCEPTANCE

GAL.

MAX. TEMP.

°F

MAX. PRESS.

PSIG

WEIGHT

LBS

NOTES

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

CONSTRUCTION BID

DOCUMENTS

FULLY SPRINKLERED

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

PRIME CONSULTANT STAMPCONSULTANT

321 4 5 6 7 8 9 10

636-18-304

X

CONSTRUCT COMBINED

ENERGY PLANT PHASE 1

5350 W 94TH TERRACE #102

PRAIRIE VILLAGE, KS 66207

T 913.258.5026 www.rossbar.com

4101 WOOLWORTH AVE

OMAHA, NE 68105

11/30/2021

NOT F

OR

CONSTRUCTIO

N

D U s e rs

\m s im m o n s \D o c u m e n ts

\2 -1

M

E C

H v m s im m o n s L W

R W

.r v t

/5

/2

:5 :5

P

M

0-M-602

MECHANICAL SCHEDULES

JES MDS

Revisions: Date:

ADDENDUM NO. 01 04/07/2022

4. PROVIDE ISOLATION VALVE BETWEEN RECIEVER AND PUMP.

3. PROVIDE MECHANICAL ALTERNATOR TO SWITCH LEAD/LAG PUMP OPERATION.

2. PROVIDE CONCRETE HOUSEKEEPING PAD PER SPECIFICATIONS.

1. PROVIDE WITH FLOAT SWITCH, ALTERNATOR, AND ALL CONTROLS REQUIRED FOR PUMP OPERATION.

NOTES:

CONDENSATE PUMP SCHEDULE

MARK

MFR. MODEL TYPE LOCATION SERVICE

RECEIVER

CAPACITY

(GAL)

RECEIVER

VENT SIZE

# OF

PUMPS

PRESSURE POWERED PUMP

NOTES

ID #

CAPACITY

(LB/HR)

MOTIVE INLET

PRESS (PSIG)

BACK PRESS

(PSIG)

SPCP 1 ARMSTRONG DPT-404RP STEAM POWERED MEZZANINE STEAM CONDENSATE 50 4" 2 4400 30 15 1-4

T

SP

SA

RA

TT

C W

S

C W

R C

C

RA-T

MOA-D

PF-PD

MA-T

RA-D

PHC-LAT

CC-VLV

SA-LAT

SA-SP

EOA-F

NO

SP

BLD-P

T

MA-FRZST

SMOKE DETECTOR

FURNISHED AND INSTALLED,

AND INTERLOCKED WITH FIRE

ALARM CONTROL PANEL BY

DIV. 28

SD

SUPPLY

FAN

VFD

SF-S

SF-SS

SF-DATA

SF-SPD

AFMSSA-F

DP

H W

S

H W

R

PHC-VLV

NO

P H

C

MOA-F

EOA-D

EOA-D-S

MOA-D-S

RA-D-S

T

CC-LAT

SMOKE DETECTOR

FURNISHED AND INSTALLED,

AND INTERLOCKED WITH FIRE

ALARM CONTROL PANEL BY

DIV. 28

SD

SD

SF-FAULT

SD-D

SD-D-S

SMOKE DAMPER FURNISHED

AND INSTALLED, AND

INTERLOCKED WITH FIRE

ALARM CONTROL PANEL BY

DIV. 23

O A

N C

A M

S A

M S

N C

T S

D N

O N

O 1

EF-X-S

EF-X-SSSTARTER

CT

EA OUTEA IN

BD

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

CONSTRUCTION BID

DOCUMENTS

FULLY SPRINKLERED

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

PRIME CONSULTANT STAMPCONSULTANT

321 4 5 6 7 8 9 10

636-18-304

X

CONSTRUCT COMBINED

ENERGY PLANT PHASE 1

5350 W 94TH TERRACE #102

PRAIRIE VILLAGE, KS 66207

T 913.258.5026 www.rossbar.com

4101 WOOLWORTH AVE

OMAHA, NE 68105

11/30/2021

NOT F

OR

CONSTRUCTIO

N

D U s e rs

\m s im m o n s \D o c u m e n ts

\2 -1

M

E C

H v m s im m o n s L W

R W

.r v t

/5

/2

:0 :0

P

M

0-M-703

MECHANICAL CONTROLS

JES MDS

NTS

AIR HANDLING UNIT CONTROL DIAGRAM

AIR HANDLING UNIT (AHU-X) POINTS LIST - NO HEAT RECOVERY

CONTROL

POINT TAG SYSTEM POINT DESCRIPTION

INPUTS OUTPUTS ALARM REPORTS

DI AI DO AO H

IG

H \L

O W

L

IM

IT

S A

F E

T Y

M A

IN

T

A N

E N

C E

A B

N O

R M

A L O

N /O

F F

O P

E N

/C L O

S E

A L A

R M

R U

N T

IM

E

T O

T A

L

IZ

A T

IO

N

T R

E N

D

BLD-P BUILDING PRESSURE ● ● ● ●

CC-LAT COOLING COIL LEAVING AIR TEMPERATURE ● ● ● ●

CC-VLV CHILLED WATER VALVE ● ●

EOA-D ECONOMIZER OUTSIDE AIR DAMPER ACTUATOR ● ●

EOA-D-S ECONOMIZER OUTSIDE AIR DAMPER STATUS ● ●

EOA-F ECONOMIZER OUTSIDE AIRFLOW ● ●

MA-FRZST MIXED AIR FREEZESTAT ● ● ● ●

MA-T MIXED AIR TEMPERATURE ● ● ● ●

MOA-D MINIMUM OUTSIDE AIR DAMPER ACTUATOR ● ●

MOA-D-S MINIMUM OUTSIDE AIR DAMPER STATUS ● ●

MOA-F MINIMUM OUTSIDE AIR FLOW ● ●

PF-PD PRE-FILTER PRESSURE DROP ● ● ● ●

PHC-LAT PREHEAT COIL LEAVING AIR TEMPERATURE ● ● ● ●

PHC-VLV PREHEAT COIL VALVE ACTUATOR ● ●

RA-D RETURN AIR DAMPER ● ●

RA-D-S RETURN AIR DAMPER STATUS ● ●

RA-T RETURN AIR TEMPERATURE ● ● ● ●

SA-F SUPPLY AIRFLOW ● ●

SA-LAT SUPPLY AIR TEMPERATURE ● ● ● ●

SA-SP SUPPLY AIR DUCT STATIC PRESSURE ● ● ● ●

SD SMOKE DETECTOR ● ● ● ●

SD-D SMOKE DAMPER ● ●

SD-D-S SMOKE DAMPER STATUS ● ●

SF-DATA SUPPLY FAN VFD DATA ● ● ● ● ●

SF-FAULT VFD FAULT ● ● ●

SF-S SUPPLY FAN STATUS ● ● ● ● ●

SF-SPD SUPPLY FAN VFD SPEED ● ●

SF-SS SUPPLY FAN START/STOP ● ●

SEQUENCE OF OPERATIONS

AIR HANDLING UNIT (AHU-X)

GENERAL DESCRIPTION

The air handling unit (AHU-X) described by this sequence of operations consists of the following features. These features include a variable speed supply fan array, hot water preheating coil, and chilled water cooling coil that operate to provide heating, ventilation, and air-conditioning for the conditioned space as shown on the drawings.

OPERATING MODES

SYSTEM START UP MODE

The AHU shall be in system start up mode for after the unit has been enabled. The AHU will automatically reset to Occupied Mode after a user definable amount of time.

OCCUPIED MODE

The AHU shall be in occupied mode per the project design conditions schedule shown on the control drawings.

UNOCCUPIED MODE

The AHU shall be in unoccupied mode for all periods not included in the occupied hours of operation per the project design conditions schedule shown on the control drawings. Overrides of unoccupied schedule shall be defined by zone level controls.

ECONOMIZER MODE – OUTSIDE AIR TEMPERATURE ENABLED

The unit shall be in economizer mode when:

The supply fan status is on;

AND the…