17-26-07 Traffic Signal Specs.pdf

BC-BID-26-07

TRAFFIC SIGNAL SPECS

ITEM #TS-101

8” Aluminum

Vehicle Signal

▷ ▷ All Econolite signals are designed to meet or exceed the Institute of Transportation Engineers (ITE) standards.

About Signals Traffic and pedestrian signals represent the foundation of safety at any signalized intersection. They also represent the first, and arguably the most important, interaction motorists, bicyclists and pedestrians have with Intelligent Transportation Systems (ITS).

For more than eight decades, Econolite has led the industry in both innovation and breadth of traffic and pedestrian signal solutions for virtually every application, helping transportation agencies and Metropolitan Planning Organizations (MPOs) efficiently and cost-effectively meet evolving traffic management programs.

Each aluminum traffic signal head consists of a number of identical signal sections rigidly fastened together to present a continuous, pleasing signal appearance. Each section has a separate, completely assembled housing. The traffic signal meets or exceeds the equipment standard of the Institute of Transportation Engineers’ (ITE) latest revision. Constructed from corrosion resistant aluminum alloy castings and stainless steel hardware, each signal section unit is virtually weatherproof.

At A Glance ▷ Tested with over 80 mph wind loading on single point attachment

▷ Aesthetically designed - no protruding hinges or latches

▷ Stainless steel hardware

▷ Doors equipped with 2 latches

▷ Reversible door - left side standard, right side optional

▷ “Fast-on” tab terminal block

▷ Terminal block identifiers cast into housing

8-Inch Aluminum Signal Datasheet

ITEM #TS-101 continued

Durable Housing

Housing and door assembly die castings were designed with the aid of a computer to deliver maximum strength with minimum weight for unmatched tolerance to wind loading and resistance to knock-down damage. Corrosion resistant aluminum alloy castings and stainless steel hardware make the unit virtually immune to weathering.

Corrosion Resistant Finishes

A 90,000V negative charge is applied to the paint to insure proper application to the aluminum components. The paint is then baked on and cured in Econolite’s finishing department.

Positive Sealing

The door gasket seals out dirt and moisture, while the precision-molded lens gasket provides a second barrier to outside contamination.

Shurlock Boss

Radial angular grooves cast into the top and bottom of the signal head housing (along with Econolite Shurlock fittings) permit alignment adjustments in five-degree increments and hold the head firmly in place. Two attaching washers and three bolts make it easy to add sections. They also permit any section to be rotated independently about the vertical axis and hold each section securely in place to prevent misalignment.

Terminal Block

One five-position terminal block with “Fast-on” tabs on one side and screw clamps on the other side is provided.

Mounting points for a second block are also present. Raised letters cast into the housing identify each position on the terminal block.

Reversible Door Mounting

The door may be mounted on either side, permitting easy access to closely mounted signals. This is ideal for cluster-mounted signals. Two integrally-cast hinge lugs and latch screw slots are located on each side of the housing. Built upon a symmetrical concept, each housing is capable of providing either a right or left-hand door opening. While the left hinge is standard, the right hinge is optional and must be specified.

Versatility

In addition to most other manufacturers’ signals, the

8-inch section may be used vertically or horizontally as a single-section beacon or in combination with 12-inch sections. Flat-back housing simplifies mounting for special applications. A complete line of visors, louvers, and back-plates is available.

Basic Specifications ▷ Dimensions (less visor)

◉ 10 in. H x 10.5 in. W x 6¾ in. D

▷ Weight, typical:

◉ Poly = 7.2 lb (less visor)

◉ Glass = 7.8 lb (less visor)

▷ Standard Colors:

◉ Dark Olive Green (matches Federal Standard 595b-14056)

◉ Yellow (matches Federal Standard 595b- 13538)

◉ Dull Black (matches Federal Standard 595b- 37038)

© 2017 Econolite Control Products, Inc. All rights reserved. Econolite Control Products, Inc. is an Econolite Group, Inc.

company, and reserves the right to change or update these specifications at any time without prior notification.

mailto:sales@econolite.com http://www.econolite.com/

ITEM# TS-102

8-Inch Polycarbonate Signal

▷ ▷ All Econolite signals are designed to meet or exceed the Institute of Transportation Engineers (ITE) standards.

About Signals Traffic and pedestrian signals represent the foundation of safety at any signalized intersection. They also represent the first, and arguably the most important, interaction motorists, bicyclists and pedestrians have with

Intelligent Transportation Systems (ITS).

For more than eight decades, Econolite has led the industry in both innovation and breadth of traffic and pedestrian signal solutions for virtually every application, helping transportation agencies and Metropolitan

Planning Organizations (MPOs) efficiently and cost-effectively meet evolving traffic management programs.

Polycarbonate provides transportation agencies and MPOs with key benefits such as reduced weight, corrosion resistance and reduced maintenance. Reduced weight is necessary when adding signals to existing mast arms or new longer reach structures. Polycarbonate signals are also less susceptible to corrosion in high humidity applications, as well as pitting from sand in high wind areas. Each traffic signal consists of a number of identical polycarbonate signal sections rigidly fastened together to present a continuous, attractive appearance. Each section has a separate and complete housing. The traffic signal meets or exceeds the latest version of the equipment standard from the Institute of Transportation Engineers’ (ITE).

At A Glance ▷ Tested to ITE-required wind loading on a single-point attachment

▷ Reversible door - left side standard, right side optional

▷ Lower maintenance with molded-on color

▷ Stainless steel hardware

▷ Doors equipped with 2 latches

▷ “Fast-on” tab terminal block

▷ Provisions for 2 five-position terminal blocks in each housing

8-Inch Poly Signal DatasheetITEM# TS-102 continued

Housing

The housing of each section is a one-piece molded ultraviolet and heat-stabilized polycarbonate unit. Two integrally-cast hinge lugs and latch screws are cast on each side of the housing. Built upon a symmetrical concept, each housing is capable of providing either right or left-hand door openings. While the left hinge is standard, the right hinge is special and must be specified. The top and bottom of the housing have openings to accommodate standard 1½-inch pipe brackets. Each signal section is rigidly attached, one above the other, by means of corrosion-resistant bolts and a washer attachment that allow sections to be rotated about a vertical axis. Alternate means for attaching sections together are available. The housing consists of four matching punch-out locations, on the top and bottom of each section, to allow sections to be bolted together with four 1½-inch and

10-32 corrosion-resistant screws.

The top and bottom of the signal housing have an integrally-cast Shurlock boss. The radial angular grooves of the

Shurlock boss, when used with Shurlock fittings, provide positive five-degree increment positioning of the entire signal head to eliminate rotation or misalignment of the signal. Each housing has cast bosses for two five-position terminal blocks. Each housing has provisions for easily adding a back-plate. Hinge pins, door latching hardware, visor back-plate, and lens clip screws are high-quality stainless steel.

Wiring

Each receptacle provides two leads with “Fast-on”-type terminals. Wires are color coded per customer specifications.

The lamp receptacle conductors are No. 18 AWG (or larger)

600V appliance wiring material, which conforms to Military

Specification MIL-W-16878 D, Type-B with a vinyl nylon jacket rated 115°C.

Terminal Block

Each complete signal face is provided with a terminal block.

The terminal block is placed in the bottom section, unless otherwise specified. The terminal block for a standard three-section head is a five-position, ten-terminal, barrier-type strip. To one side of each “Fast-on” terminal strip is the attached AC common, red, yellow, and green signal section leads, leaving the opposite screw clamp terminal for field wires.

Basic Specifications ▷ Dimensions (less visor)

◉ 10 in. H x 10 in. W x 6 5⁄8 in. D

▷ Weight, typical:

◉ Poly = 3.1 lb (less visor)

◉ Glass = 3.65 lb (less visor)

▷ Standard Colors:

◉ Dark Olive Green (matches Federal Standard 595b-14056)

◉ Yellow (matches Federal Standard 595b- 13538)

◉ Dull Black (matches Federal Standard 595b- 37038) mailto:sales@econolite.com http://www.econolite.com/ jsacchinelli Highlight

Traffic Signals

Peek Traffic Corporation, a Signal Group Company 2906 Corporate Way Palmetto, FL

34221 (941) 845-1200 | (800) 245-7660 www.peektraffic.com

Unique design and technological advantages make Peek Traffic Signals “Best in class”

Polycarbonate Signals

• Unaffected by scratches

• Impregnated color means that they never need painting

• Impervious to corrosive atmospheres

• One-piece doors, grooved.

• Simple alignment and positive locking in 5 degree steps

• Ribbed for structural stability

• Reinforced plates available

• Adaptable to span wire or mast suspension

• Universal vertical and horizontal ready mounting ar-rangement

• Exterior hardware in stainless steel available

• LED ready or equipped with reflectors

• Weather proof and dust tight one piece doors plus gasket

• Fifty percent lighter than aluminum

Aluminum Signals

• Equipped with exterior stainless steel hardware

• Doors and lens gaskets make the signal weather-proof and dust-tight

• Integral visor rims prevent leakage

• Available reflectors in Alzak ®

• The lamp receptacle can be rotated 360 degrees for filament alignment

• Integral locking rings included

• Adaptable for span wire, mast arm suspension, side pole or post top mounting

Item# TS-103

Item# TS-104

ITEM#'s TS-103 & TS-104 jsacchinelli Highlight jsacchinelli Highlight

Specifications

Ultraviolet-stabilized polycarbonate resin (having a minimum thickness of 0.100 inch-es), Stainless steel exterior hardware.

Couplers are standard steel-zinc, but a stain-less steel option is available.

Snap-out assembly. Swing out frame.

Lane control uses a standard reflector.

Heat-resistant molded phenolic, Rotatable through 360°. Pre-wired with 26” #18 AWG 105°C type TEW color-coded leads with Quick-disconnect terminals

Accommodates three 3/4” diameter cables

1-section 2-point 2-section 3-point 3-section 5-point 4-section 5-point 5-section 5-point and 5 point

Integral 72-tooth serrated adjustable in 5° steps.

8” (200mm) LED-Ready Section = 1.85 lb (0.84kg) 12” (300mm) LED-Ready Section = 3.15 lb (1.43kg)

8”(200mm) Section = 9.75”W x 10”Hx 6.16”D 12”(300mm) Section = 13.5”W x 13.44”H x 6.44”D

Die-cast aluminum alloy housing and door.

Stainless steel exterior hardware. Couplers are standard steel-zinc, but a stainless steel option is available.

Electrostatically applied powder coat with five stage iron phosphate treatment.

Snap-out assembly. Swing out molded frame.

Lane control uses a standard reflector

Heat-resistant molded phenolic, Rotatable through 360°. Pre-wired with 26” #18 AWG 105°C type TEW color-coded leads with Quick-disconnect terminals

Accommodates three 3/4” diameter cables

1-section 2-point 2-section 3-point 3-section 5-point 4-section 5-point, 2-point 5-section 5-point×2, and 3-point

Integral 72-tooth serrated adjustable in 5° steps.

8” (200mm) LED-Ready Section = 4.2 lb (1.9 kg) 12” (300mm) LED-Ready Section = 5.5 lb (2.5 kg)

8”(200mm) Section = 9.75”W x 10”Hx 6.16”D 12”(300mm) Section = 13.5”W x 13.44”H x 6.44”D

Material

Reflector

Lamp receptacle

Wire opening between sections

Terminal block

Signal alignment

Weight

Overall dimension

Material

Finish

Reflector

Lamp receptacle

Wire opening between sections

Terminal block

Signal alignment

Weight

Overall dimension

Polycarbonate Aluminium

One Year Limited Warranty.

Signal Group warrants* these products against manufacturing defects in materials and workmanship for one year from date of shipment from the Signal Group factory. Specific contracts and regional laws may vary or alter these terms. Signal Groupproducts are protected by one or more U.S. and international patents.

* For specific warranty information, contact your local Signal Group prod-uct representative.

Poly and Aluminum signals are also available with LED ready Weights do not include hardware modifications. Door only, no visors.

Peek Traffic Corporation A Signal Group Company

2906 Corporate Way Palmetto, FL 34221

(941) 845-1200 | (800) 245-7660 www.peektraffic.com

About Signal Group – covers a broad range of quality turnkey traffic control products and services. Signal Group products have helped to make motorists around the world safer and their travels more pleasant and efficient. This expertise, experience, and breadth of product lines has made Signal Group one of the most respected and recognized leaders in the traffic control marketplace The information contained in this publication is presented for informational purposes only, and while every effort has been made toensure its accuracy, the information is not to be construed as warranty or guarantee, express or implied, regarding the products orservices described herein or their use or applicability. No license is granted by implication or otherwise to any of Signal Group’sintellectual property. Signal Group reserves the right to alter or revise any of its products or published technical data related thereof at any time without notice. ©2012 Signal Group. Intersection image is licensed through CreativeCommons.org

ITEM#'s TS-103 & TS-104 www.mccain-inc.com

Cabinets

Controllers

Signals

Signs

Software

Specialty

Overview

Benefits Product Description

McCain’s Programmable Traffic Signals are rugged, high performance, directional traffic signals used to limit signal visibility to specific target areas and increase intersection safety. These 12-inch traffic signals feature a focused and directional beam for precise lane control or to avoid motorist confusion when two intersections are in close proximity. McCain, an industry leader in signal manufacturing and supply, offers an extensive range of configurations and accessories, including backplates, visors, and signal assemblies to match all your traffic signal requirements.

• Provide superior visibility

• Help reduce accidents and improve traffic flow

• Configure to meet your needs and specifications

• Stand the test of time with weather-tight doors and corrosion-resistant aluminum fabrication

• Available with a full range of accessories including;

backplates, visors, and mounting hardware

The McCain aluminum Programmable Traffic Signals are modular in design allowing them to be assembled in a variety of configurations. Signals are compatible with 115 VAC, three-prong, incandescent bulbs, and LED assemblies.

Programming is accomplished through the use of a Fresnel lens and a smaller clear lens. Masked-off portions of the smaller lens control which signal faces each lane sees during approach.

Signal sections can be tilted in two-degree increments for a maximum of ten degrees above and below the horizontal axis while still maintaining a common vertical axis.

The incandescent version of the signal head has an automatic dimming circuit to adjust light output according to environment conditions.

Programmable Traffic Signal

ITEM# TS-105

® © 2015 McCain Inc. Updated 04/08/2015. McCain reserves the right to change product specifications without notice.

For the most up-to-date information, please contact McCain.

2365 OAK RIDGE WAY // VISTA, CALIFORNIA 92081 // USA // WWW.MCCAIN-INC.COM

To learn more about McCain’s Integrated Traffic Solutions, please contact info@mccain-inc.com or call (760) 727-8100

Typical Configurations

Vertical Horizontal Doghouse

Top

Front

Side

3-Section

Dimensions rounded to the nearest 0.1”

Vertical dimension of 3-section is approximate

3-section shown as typical configuration with backplate and 4o tilt

Standard Features

• Individual modular sections

• Reinforcing ribs on top and bottom of housings for extra rigidity

• Stainless steel door roll pins and eye bolt/wing nut assemblies

• Moisture proof and dust tight neoprene gasket fitted to the gasket channel cast in the door perimeter

• 5-position, barrier-type terminal block with quick-disconnect terminals on one side of each position and screw clamp terminals on the other side of each position

• 3-prong, PAR-46 lamp secured by a wire ring and a spring load clip

• Acrylic lenses colored to ITE specifications

• Masking kit

General Specifications Dimensions: 13.3” H x 13.3” W x 18.0“ D (1 section)

Material: Housing: Cast aluminum, type 360, reduced corro-sion, increased powder coat adhesion Door Hardware: Stainless steel

Finish(es): Powder coated

Color(s): Federal yellow, signal green, black, or custom colors

Access: Front door (1), rear door (1)

Lamp: PAR-46, 115 VAC, 150 W

Environmental: Operating temperature: -37° C to +74° C Humidity: 0 to 95% (non-condensing)

Shipping Weight: 23 lbs (1-section)

Options

• Visors

• Backplates

• Mounting preset tilt angles

• 0° - horizontal mount

• 4° - standard mount, MAT mount

• 8° - MAS mount

• Various framework and fittings, orientation, and configurations Light Source: LED or incandescent

Programmable Traffic Signal ITEM# TS-105

At A Glance ▷ �Slim profile, allowing for 5% less weight than the alternatives

▷ �Mounts left or right with use of the side mount bracket

▷ �Reduced energy consumption

- up to 90% less energy consumption than pedestrian signals with incandescent lamps

▷ �Meets or exceeds applicable Institute of Transportation Engineers (ITE) specification

▷ �Outlasts neon and incandescent lighting

▷ No LED “Hot Spots”

About Signals Traffic and pedestrian signals represent the foundation of safety at any signalized intersection. They also represent the first, and arguably the most important, interaction motorists, bicyclists and pedestrians have with Intelligent Transportation Systems (ITS).

For more than eight decades, Econolite has led the industry in both innovation and breadth of traffic and pedestrian signal solutions for virtually every application, helping transportation agencies and Metropolitan Planning Organizations (MPOs) efficiently and cost-effectively meet evolving traffic management programs.

Econolite also leads the way in ultra-bright LED (Light Emitting Diode) technology’s use in traffic signal applications.

More visible than traditional incandescent bulbs, LED signals increase overall safety for all roadway users. In addition, since LEDs are longer-lasting and require significantly less energy than their incandescent counterparts, which yields significant budgetary savings.

16-Inch LED Aluminum Pedestrian Signal

▷ ▷All Econolite signals are designed to meet or exceed the Institute of Transportation Engineers (ITE) standards.

ITEM#'s TS-106 & TS-107

1250 N. Tustin Avenue, Anaheim, CA 92806 ∙ 714-630-3700 ∙ sales@econolite.com ∙ www.econolite.com

© 2018 Econolite all rights reserved. Econolite reserves the right to change or update these specifications at any time without prior notification.212041016 -5

LED Specifications

• Voltage Range 80V to 135V AC; normal 120V AC (less than

10% variation in intensity)

• �Power: Maximum 15W Hand; maximum 10W Pedestrian

• �Operating Temperature: -40°C to +74°C

• �Storage Temperature: -40°C to +93°C

• Power Factor Correction: >0.90

• Total Harmonic Distortion: <20%

• Dimensions: 18 in. x 16 in. x 4.5 in.

• �Fuse and transient suppressor incorporated for line and load protection

• �LEDs interconnected to minimize effect of LED string failure

• �Meets or exceeds NEMA Moisture Resistance STD 250-1991 for Type-4 enclosures (ITE 6.4.6.2 Moisture Resistance)

Field Terminal Assembly The field terminal assembly includes a three-terminal pair (six-screw) type terminal block for termination of the three field wires for AC (+) for the HAND display, AC (+) for the PEDESTRIAN display, and AC (-). Connected to the opposite side of these terminals is a pigtail lead. The free end of each lead is terminated with an insulated female quick-disconnect socket that mates with the male lug, supplied on the message module.

The field terminal assembly includes an aluminum base or back-plate that is bolted to the signal housing.

LED Option The LED module is a fully-encapsulated LED HAND/ PEDESTRIAN module. The LED PC board is enclosed in a plastic module and is mounted to be impervious to shocks generated during shipping, handling, and installation. In order to facilitate installation and maintenance, the signal is designed so that the LED message module is removable and the field wiring terminals are readily accessible from the front by merely opening the signal door. The rear of the tray provides three male quick-disconnect lugs for connection of AC (+) for the HAND display, AC (+) for the PEDESTRIAN display, and AC (-).

The tray is sealed with a 1⁄8-inch (3 mm) clear, UV-stabilized, refraction-type, 3⁄16-inch polycarbonate lens which is weather, craze, and heat resistant. The module is further sealed with a one-piece Ethylene Propylene Diene Monomer (EPDM) neoprene gasket fitted around the perimeter to provide positive protection of the enclosed LEDs and electronics from handling, weather, and moisture. Removal and insertion of the module does not require the use of tools.

Basic Specifications ▷ Overall Dimension

◉ 18” W x 16.5” H x 5” D (457 x 419 x 178 mm)

▷ Weight ◉ The weight of the signal, excluding mounting hardware, is 23 pounds, maximum.

▷ Standard Colors Are:

◉ Dark Olive Green (matches Federal Standard

595b-14056) ◉ Yellow (matches Federal Standard 595b-

13538) ◉ Dull Black (matches Federal Standard 595b-

37038)

16-Inch Aluminum Ped Signal Datasheet

Messages are displayed in the Portland Orange “HAND” and the Lunar White “PEDESTRIAN”, illuminated by multiple configuration Light-Emitting Diodes. The “HAND” and “PEDESTRIAN” symbols are each a minimum of 12 inches in height and seven inches in width and are configured as shown in the Manual on Uniform Traffic Control Devices (MUTCD).

Solar Screen Visor Option The Solar Screen visor option is designed to eliminate sun phantom and minimize damage to the LED signal module.

The Solar Screen visor is installed parallel to the face of the “HAND/PEDESTRIAN” symbol. The Solar Screen visor assembly is held in place by the use of stainless steel screws.

The Solar Screen assembly consists of a minimum of 20 straight horizontal louvers and 21 zigzag pattern horizontal louvers.

Warranty The entire pedestrian signal, including LEDs, solid-state control, and polycarbonate parts, are warranted for one year from the date of original shipment against defects in workmanship and/ or materials.

ITEM#'s TS-106 & TS-107

C m C oa >i m

3:,, m ca

>i ...

C :I u

C Cl) m la Cl) ca

3:

en Cl)

3:...

e ca

C

!I !S DRAWING OR SPECIFICATION IS CONFIDENTIAL

D PROPRIETARY TO NATIONAL SIGN AND SIGNAL

. AND IT MAY NOT BE REPRODUCED, USED, OR

�CLOSED TO OTHERS WITHOUT THE WRITTEN

�NSENT OF NATIONAL SIGN AND SIGNAL INC.

Cl) .., 26 7/8"-------1

24"--------i

LTR REVISIONS

BACK PLATE

(.063 ALUM.)

DATE

oa >i m

3:

S.S. HINGE

(1 1/4" X 3Q")

18"-----l 1-4 7/16" ,-rT:7 ,, m e ca

32 7/8" 30"

NOTES:

I 4 1/2"D

_I

3 1(2"0

3 ,}2"0

3 1(2"0

3 1(2"0

I I I I I I

I ri-� I t.L.J I I I I I p-;il I 1 ·11 lt,_..il I I oogoo

I I � 7 p-::i1 � I I 11 lt,_.JI g0 oOo o0 O 0 0 0 0 0 0 0 O 0 0 0

0 0 0 o 0

: o:

00000

:ooo

0 0 0o0

0 0 o 0 0000°

0 O 0000 � �o 0 0

0 0

0 0 0 0

00000

1 AMP FUSE, FUSEHOLDER,

AND M.O.V.

g° ooo

0 0 0 0 0 0 0 0 0 0

0000°

00000 gooo

0 0

0 0 0000°

0 0

0 0 o o oD o o o

0 0 0 0

0 0 g o Oo

0 0 0000

I I I r-� l,_,i

00000 l

� I i t-�1,_.J :a : I o o o I : \: p--:1 � oo: I ·1

0 0

: 0� 00 0 0 0 O 0 0 0 f-.J

LED ELECTRONIC DRIVER

(118-0805)

1. MESSAGE SHALL BE FORMED BY SINGLE ROWS OF WHITE LED'S SPACED AT

1/2" O.C. (NOMINAL).

2. MESSAGE COLOR SHALL BE WHITE ILLUMINATION.

3. MESSAGE SHALL COMPLETELY BLANK OUT WHEN NOT ENERGIZED.

4. LED OUTPUT POINTS SHALL BE PROTECTED BY A MATTE/CLEAR POLYCARBONATE

LENS AND SHALL MINIMIZE ANY UNWANTED REFLECTIONS.

5. SIGN HOUSING TO BE FIELD DRILLED FOR POWER ENTRY AND MOUNTING.

6. SIGN SHALL BE EQUIPPED WITH FOUR (4) 3/16" DIA. WEEP HOLES LOCATED

IN THE LOWER CORNERS OF THE HOUSING.

7. ENTIRE HOUSING ASSY. SHALL BE ACID ETCHED AND PAINTED WITH TWO COATS

OF ZINC-CHROMATE PRIMER. DOOR FRAME, FACE PLATE, AND INTERIOR OF HOUSING

AND VISOR SHALL BE PAINTED WITH TWO COATS OF HIGH QUALITY FLAT BLACK

ENAMEL. EXTERIOR OF HOUSING SHALL BE PAINTED WITH TWO COATS OF HIGH

QUALITY SEMI-GLOSS BLACK ENAMEL.

8. APPROXIMATE WEIGHT OF SIGN ASSY. - 60#

VISOR � (.063 ALUM.) ---------

1 / 4-TU RN LOCKS

(S.S.)

3" x 1 /4" ALUM. STIFFENERS HELi-ARC WELDED TO INTERIOR

OF HOUSING, TYPICAL

RESISTOR BOARD ASSYS. .125" MATTE/CLEAR

(102-1025-2) POLYCARBONATE

FACE PLATE

(.080 ALUM.)

HIGH OUTPUT WHITE LED'S

F.O. DOOR FRAME

(.125 EXTRUDED ALUM.)

FACTORY NEUTRAL WIRES

HOUSING

1-1/2"' NPT MTG HUB

ALUM.

(.125 EXTRUDED ALUM.)

E[] 120 VAC

CHASSIS GROUND

TERMINAL STRIP

CONNECTION

UNLESS OTHERWISE SPECIFIED,

ALL DIMENSIONS HAVE A

TOLERANCE OF± 1/4"

DRAWN BY:

P.H.

DATE: 03/18/11

OUR JOB NO. N/A

CUSTOMER/JOB NO.:

"4

TITLE

24"

LED

SCALE

1: 10

NATIONAL SIGN AND SIGNAL

301 S. ARMSTRONG RD BATTLE CREEK, Ml 49015

MODEL #2430LEDNLTAT

x 30" 1 MESSAGE / 1-WAY

BLANK-OUT SIGN

REVISION I SIZE DRAWING NO.

A S1982A-2

ITEM#'s TS-114, TS-115, TS-116, TS-117, TS-118, TS-178, TS-179

ITEM#'s TS-114, TS-115, TS-116, TS-117, TS-118

ITEM#'s TS-114, TS-115, TS-116, TS-117, TS-118, TS-178, TS-179

ITEM#'s TS-114, TS-115, TS-116, TS-117, TS-118, TS-178, TS-179

ITEM# TS-137

ITEM#'s TS-149 & TS-150

Highlight

ITE | Traffic Signals

ITEM#’s TS-161, TS-162, TS-163, TS-164, TS-165, TS-166, TS-167, TS-168, TS-169

Uniform Appearance LED Traffic Signal Modules Features & Benefits

• *Fully compliant to ITE VTCSH-LED Circular Signal Supplement dated 6/27/2005

• Industry’s lowest power for all colors

• Meets or exceeds ITE intensity, color & uniformity spec, including 49ºC / 74ºC requirements

• Temperature compensated power supplies for longer LED life

• Uniform appearance

• Expanded view radiation pattern suitable for span wire and steep grade applications

• Transient suppression exceeds ITE and NEMA specifications (Up to 6KV ring wave)

• Manufactured with anti-capillary wires

• Conformal coated power supply

• Secondary lens treatment for abrasion resistance

• Patent No. 7,281,818 and other patents pending

• Intertek/ETL certified and listed on ETL certification program

• All units operate at 80-135VAC RMS, 60+/-3Hz

County Part Number

Part Number Color Lens Type

Dominant

Wavelength (nm)

Typical Wattage at 25oC

Peak Minimum Maintained

Luminous Intensity (cd) Size (in)

*Meets ITE

Spec

CSA

Approved

TS-161 433-1110-003XL Red Tinted 625 7 165 8 • •

TS-162 433-3130-901XL Yellow Tinted 590 8 410 8 • •

TS-163 433-2120-001XL Green Tinted 500 7 215 8 • •

TS-164 433-1210-003XL Red Tinted 625 7 365 12 • •

TS-165

TS-166

433-3230-901XL Yellow Tinted 590 9 910 12 • •

433-2220-001XL Greem Tinted 500 8 475 12

Omni-Directional Uniform Appearance LED Arrow

Features & Benefits

• *Fully compliant to ITE VTCSH-LED Vehicle Arrow Supplement dated 7/01/2007

• Allows for mounting in any orientation in the signal head

• Industry’s lowest power for all colors

• Meets or exceeds ITE intensity, color & uniformity spec, including 49ºC / 74ºC requirements

• Temperature compensated power supplies for longer LED life

• Uniform appearance

• Transient suppression exceeds ITE and NEMA specifications (Up to 6KV ring wave)

• Manufactured with anti-capillary wires

• Conformal coated power supply

• Secondary lens treatment for abrasion resistance

• Intertek/ETL certified and listed on ETL certification program

• All units operate at 80-135VAC RMS, 60+/-3Hz

County Part Number

Part Number Color Lens Type

Dominant

Wavelength (nm)

Typical Wattage at 25oC

Peak Minimum Maintained

Luminous Intensity (cd)

*Meets ITE

Spec

CSA

Approved

TS-167 432-1314-001XOD Red Tinted 628 6 56.8 • •

TS-168 431-3334-901XOD Yellow Tinted 590 7 141.6 • •

TS-169 432-2324-001XOD Green Tinted 500 6 73.9 • •

ITEM #TS-170

Operating Voltage Range:

80VAC to 135VAC (120VAC nominal)

Convex lens reduces glare & sun reflection

Fuse and transient suppressor incorporated for line and load protection

Operating Temperature Range: -40°C to +74°C

Turn-On/Turn-Off Time = 75 msec max

Power factor >0.9

Total harmonic distortion <20%

Meets FCC Title 47, Subpart B, Section 15 Regulations for electrical noise

Conforms to MIL-STD-810F for blowing rain

Provided with quick connect terminals and spade adapters

Written manufacturer’s warranty available on request

All products traceable by serial number

BI-MODAL

GREEN & YELLOW

LED ARROWS

Easy to install into existing signal enclosure

Long life; up to 10 times longer than incandescent

FEATURES / BENEFITS

SPECIFICATIONS

12” (300mm) - 120 VOLT ARROWS

County Item Number

Part Number Description CSA Approved

Lens Type

Typical Wattage at 25oC Dominant Wavelength

(nm)

TS-170 430-6370-001 Bi-Modal Green/Yellow

Clear 6/7 505/590

Electrical Specifications:

Operating voltage: 80V AC - 135V AC (120V AC nominal)

Operating temperature: -40°F to +165°F (-40°C to +74°C)

Turn-on / Turn-off Time: 75 msec max

Power Factor: > 0.9

Total Harmonic Distortion: < 20%

LED Lamp Modules for PV Signals P46 Series

On when it counts.

Features & Benefits

• Direct retrofit replacement for incandescent lamps used in

Programmable Visibility (PV) signals

• Compatible with McCain and 3M signal heads

• CalTrans qualified

• 90% reduction in power vs. incandescent

• Failure of single LED results in loss of light from that LED only

• Moisture and dust resistant

• Fuse and transient suppressor incorporated for line and load protection

• Meets FCC Title 47, Subpart B, Section 15 Regulations for electrical noise

• Conforms to MIL-STD-810F for blowing rain

• Written warranty available on request

• All products traceable by serial number

Ordering Information www.dialight.com | MDTSPVSX001_G 1

Part Number Color Dominant Wavelength (nm) Typical Wattage @ 25oC Minimum Luminous Intensity* (Cd)

P46 Series - 120V Programmable Visibility Modules

P46-3R33-003 Red 622 10 500

P46-3Y33-003 Yellow 590 15 500

P46-3G33-003 Green 505 8 500

Dialight reserves the right to make changes at any time in order to supply the best product possible. The most current version of this document will always be available at: www.dialight.com/ Assets/Brochures_And_Catalogs/Signaling/MDTITEXOD15X001.pdf Warranty Statement: EXCEPT FOR THE WARRANTY EXPRESSLY PROVIDED FOR [HEREIN/ABOVE/BELOW], DIALIGHT DISCLAIMS ANY AND ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE, TITLE, AND NONINFRINGEMENT.

ITEM# TS-171, TS-172, TS-173

TS-171

TS-172

TS-173

jsacchinelli Highlight jsacchinelli Highlight jsacchinelli Highlight

1.844.412.8395 | traffic@carmanah.comcarmanah.com

R920-E Solar-Powered Rectangular Rapid Flashing Beacon Data Sheet

Rectangular rapid flashing beacons (RRFBs) improve pedestrian safety by increasing yield rates to 72-96% at crosswalks:

DMeets 11th Ed. MUTCD (Chapter 4L) and MUTCDC Canada Standards and is Buy America/ BABA compliant

DCompact and lightweight solar engine

DAudible pushbutton activation with all ADA compliance features

DSolar Power Report™ (SPR) prepared for every location to ensure battery longevity

Superior Design and Technology The R920-E utilizes a self-contained solar engine integrating the Energy Management System (EMS) with an on-board user interface, housed in a compact enclosure together with the batteries and solar panel. MUTCD interim approval IA-21 flash pattern and multiple configurations enable the R920-E to handle all crosswalk applications.

Easy Installation With its highly efficient and compact design, installation is quick and uncomplicated, dramatically reducing installation costs. Retrofitting can be done where existing sign bases are used to enhance existing marked crosswalks in minutes, and new installations can be completed without the cost of larger poles, new bases, and trenching.

Advanced User Interface The R920-E comes with an on-board user interface for quick configuration and status monitoring. It allows for simple in-the-field adjustment of flash pattern, duration, intensity, ambient auto adjust, night dimming, and many more. Settings are automatically sent wirelessly to all units in the system.

Reliable Every solar-powered model is solar-sized by location to ensure year-after-year operation. Carmanah includes a Solar Power Report to prove sustainability over a 12-month period.

COM P L IAN

T

MUTCD

compliant

Buy America compliant

Solar-sized for every location

5-year limited warranty mailto:traffic%40carmanah.com?subject= https://carmanah.com

R920-E Solar-Powered Rectangular Rapid Flashing Beacon Data Sheet

1.844.412.8395 | traffic@carmanah.com | carmanah.com

LIGHT BAR CONFIGURATION

Uni-directional Configuration Bi-directional Configuration

IN-THE-FIELD AIMING

Rotate the light bar towards the incoming vehicle lane, independent of the wire hole location.

On-Board User Interface (OBUI)

Adjustable system settings with auto-scrolling LED display on our latest EMS

System test, status, and fault detection: battery, solar, button, beacon, radio, day/night

Flash patterns meet MUTCD 11th Ed. (4L.03) Standards

Input: momentary for pushbutton activation, normally open switch, normally closed switch, dusk-to-dawn operation

Flash duration: 5 sec. to 1 hr.

Intensity setting: 20 to 1400 mA for multiple RRFBs, circular beacons, or LED enhanced signs

Nighttime dimming: 10 to 100% of daytime intensity

Ambient Auto Adjust: increases intensity during bright daytime

Automatic Light Control: reduces intensity if the battery is extremely low

Temperature correction: yellow beacons

Calendar: internal time clock function

Radio settings: enable/disable, selectable channel from 1 to 14

Output: enabled when beacons flashing daytime and nighttime, or nighttime only

Activation counts and data reporting via OBUI or optional USB connection

Beacon Communication

Encrypted, wireless radio with 2.4 GHz mesh technology

Wireless update of settings from any unit to all systems on the same radio channel

User-selectable multiple channels to group different beacons and ensure a robust wireless signal

Communicates with all other Gen III radio-enabled systems including our R820-E, -F, and -G circular beacons

Instantaneous wireless activation: <150 ms

Wireless range: 1000 ft (305 m)

Integrated, vandal-resistant antenna

Energy Collection

15 W high-efficiency photovoltaic solar panel

45 deg tilt for optimal energy collection

Maximum Power Point Tracking with Temperature Compensation (MPPT-TC) battery charger for optimal energy collection in all solar and battery conditions

Energy Storage

12 V 14 Ahr. battery system

Replaceable, recyclable, sealed, maintenance-free, best-in-class AGM batteries offer the widest temperature range and longest life

Battery design life: +5 yrs.

Tool-less battery change with quick connect terminals and strapping for easy installation

Solar Engine Construction

Weatherproof, gasketed enclosure with vents for ambient air transfer

(NEMA 3R)

Lockable, hinged lid for access to on-board user interface and batteries

Corrosion-resistant aluminum with stainless steel hardware

Raw aluminum finish or yellow, black, or green powder coated

Prewired to minimize installation time

High-efficiency optics and EMS = the most compact, lightweight system

19 lb (8.6 kg) including batteries, excluding beacons and pushbutton

Environmental

-35 to 165° F (-37 to 74° C) system operating temperature

-40 to 140° F (-40 to 60° C) battery operating temperature

150 mph (241 kph) wind speed as per AASHTO LTS-6

Activation

Pushbutton: ADA-compliant, piezo-driven with visual LED and two-tone audible confirmation

Audible pushbutton station: ADA-compliant, piezo-driven with visual LED and customizable voice message confirmation

Warranty 5-year limited warranty, 1-year limited on batteries

Customize Build an RRFB online

SYSTEM SPECIFICATIONS

BEACON SPECIFICATIONS

Optical

Configurable to MUTCD 11th Ed. (Chapter 4S) Standard

Purpose-built light bar optics = maximum efficiency and no stray light Exceeds SAE J595 class 1 intensity by 2.5 to 3x when used as recommended Meets SAE J578 chromaticity

3 in (76 mm) x 7 in (178 mm) clear, UV-rated polycarbonate lens with yellow LEDs

High-power LEDs: +90% lumen maintenance (L90) based on IES LM-80

Side-emitting pedestrian confirmation LEDs

Independent, stainless steel mounting brackets make back-to-back installation simple and enable in-field aiming for maximum effectiveness

Yellow, black, or green powder coated light bar covers

Specifications subject to local environmental conditions, and may be subject to change.

All Carmanah products are manufactured in facilities that are certified to ISO quality standards.

“Carmanah” and Carmanah logo are trademarks of Carmanah Technologies Corp.

© 2024, Carmanah Technologies Corp.

Document: Carmanah_DATA_R920-E_RevV

SOLAR ENGINE DIMENSIONS

Bottom ViewSide View

14.6” (37.1 cm)

13.5” (34.2 cm)

4.0” (10.2 cm)

2.0”- 2.5” Perforated Square Pole Mount

2.38” - 2.88” Diameter Round Pole Mount

3.5” - 4.5” Diameter Round Pole Mount

Side Pole Mount

SOLAR ENGINE MOUNTING

mailto:traffic%40carmanah.com?subject= https://carmanah.com https://carmanah.com/custom-rrfb-crosswalk/

Blank Page