B09_YELL_205796_Amend_0003__Addendum_1_Specs.pdf

Addendum Number: ONE Date Issued: 9 April 2018

Project: Mammoth Hotel Phase II

Guest Wing Renovation

Project Number: 15021.40

Pages in Addendum: 05 + Attachments Prepared By: Dennis Johnson

Kate Tilleman

Issued To: NPS Contracting Officer for release

This Addendum consists of 05 pages and 13 attachments. Sheet A0.1 r.01, ASK 001, SSK-1, SSK-2, Sheet S1.1 r.01, Sheet S3.1 r.01, Sheet S3.2 r.01, Sheet M1.0 r.01, Sheet M3.1 r.01, Sheet M4.3 r.01, Sheet P1.0 r.01, Sheet

E1.2 r.01, & Sheet E2.0 r.01

Addendum to Contract Documents:

General Clarifications:

1) NPS Fire Chief has indicated that fire watch will not be required while fire suppression system is inactive within the work area so long as fire detection is fully functional and hot-works are not undertaken. If hot-works are to be completed without an active fire suppression system, coordination of the protective measures (including fire watch and/or fire department standby) is required with NPS structural fire personnel.

2) It is intended that all existing historic wood trims salvaged shall be treated to remove historic lead based paint coatings prior to reinstallation and/or refinishing activities.

3) The existing hardwood flooring border in the Hallways is intended to be removed and replaced with new to match existing in-kind.

4) Detail 13/A0.3 indicates siding removal and replacement only if necessary. Contractor should take steps to mitigate impacting the existing siding adjacent to replaced windows, including avoiding removal and replacement of existing siding. If siding replacement is necessary, face nailing is an acceptable method of attachment.

5) The Code Plans in the Drawings identify fire resistive requirements and locations, including floor/ceiling assemblies.

6) Window 314A.1 is a type G Window.

7) To the best of our knowledge, there is no existing sheathing above the diagonal subfloor. The

½” sheathing should be installed directly over the existing diagonal planking in all locations except where indicated on demo plans (bathroom locations to accommodate for tile install).

Those locations will have the diagonal sheathing removed and a ¾” sheathing installed instead. See details 11/S5.3 and 11/S5.5 for additional information. Additional underlayments shall be installed for specific floor finishes as required by manufacturer or to achieve flush/level transitions to adjoining materials as indicated within the documents.

8) Interior trims and walls called out to remain should be restored and if finish coatings are field verified to be well adhered and in generally good condition, may be prepared and repainted without LBP abatement.

9) It is intended that the entire existing truss with the drag strut at Grid Line 7 above the Map

Room is to be sheathed as indicated in Detail 11/S5.6.

10) Sign of the Crab Plumbing Fixtures clarifications

a. Please refer to re-issued P1.0 revised 04/09/2018 for plumbing fixture clarifications.

Project Manual (Specifications):

1) Section 012700 – Definition of Contract Line Items

a. Delete 3.1-C in its entirety and replace with the following:

C. Contract Line Item No.3: Option B – Exterior Paint Removal and Repainting

1. This item shall consist of work solely associated with removal and lead abatement of all existing paint finishes to exterior siding and trims and the new exterior paint coatings and finishes indicated within the documents as Option B.

2. Repair/replacement of damaged or deteriorated exterior wood wall finish and trim materials as indicated within the Contract Documents shall be included in Contract Line Item No.1.

3. Preparation and painting of exterior items modified or affected due to other work shall be included within their respective Contract Line Item.

4. Measurement and payment will be based on percentage complete of Work value based on the approved Schedule of Values.

5. Payment will be made at the contract lump sum price.

6. Acceptance of the work included within this option by the Contracting Officer may occur at any time up until project completion.

2) Section 013216 – Construction Schedule

a. Delete section 2.2-B-9 in its entirety and replace with the following:

9. Milestones: Include milestones indicated in the Contract Documents in schedule, including, but not limited to, the Notice to Proceed, Substantial Completion, and the following interim milestones:

a. Lobby and Registration area work

b. Other work items affecting building operations such a.

3) Section 09816 – Sheet Carpeting

a. Delete item 2.1in its entirety and replace with the following:

2.1 TUFTED CARPET

A. Basis of Design: Subject to compliance with the requirements for use at guest rooms and non-public areas, provide Shaw Custom Hospitality Carpet or approved equal including exact pattern match and finished construction.

B. Pattern: Match Architect's samples – CUSTOM SHAW HOSPITALITY.

1. Style: Y10961

2. Sample No.: Y864N-0

3. Project: Mammoth Hotel Rooms Carpet

C. Colors: Match Architect's samples – CUSTOM SHAW HOSPITALITY.

1. Pattern Field A: CE952

2. Pattern Field B: CJ627

D. Fiber Content: Solution Dye E. Pile Characteristic: Inline Scroll Loop & Cut (Yamaguichi) tip sheared.

F. Density: 38 oz./cu. yd..

G. Pile Thickness: 0.27 inches for finished carpet.

H. Stitches: 13.67 stitches per inch.

I. Gage: 1/10 J. Primary Backing: Woven polypropylene.

K. Secondary Backing: Classicbac secondary backing material.

L. Application: Heavy Traffic.

M. Warranty: 10 year.

N. Roll Width: 12 feet.

O. Applied Treatments:

1. Applied Soil-Resistance Treatment: Manufacturer's standard material.

4) Section 09816 – Sheet Carpeting

a. Delete item 2.2 in its entirety and replace with the following:

2.2 TUFTED CARPET

A. Basis of Design: Subject to compliance with the requirements for use at hallways, stairs and other public areas, provide Shaw Custom Carpet or approved equal. Carpet pattern shall match in-kind pattern and visual matching of colorways to carpet currently installed under previous phase of work.

B. Pattern: Match Architect's samples – CUSTOM SHAW HOSPITALITY.

1. Pattern 1 – PF38293-1 – EcoEvolution Weave 36 in custom pattern.

a. Sample No.: X839P

b. Location: Hallway & Elevator Lobbies

c. Refer to finish plans for other locations

2. Pattern 2 – PF38293-2 – EcoEvolution Weave 36 in custom pattern

a. Sample No.: X838P

b. Location: Stair S3 & S4

c. Refer to finish plans for other locations.

C. Colors: Match Architect's samples – CUSTOM SHAW HOSPITALITY.

1. Pattern: PF38293-1

a. Colors

i. Pattern Field A: C30

ii. Pattern Field B: E26

iii. Pattern Field C: G53

2. Pattern: PF 38293-2

a. Colors

i. Pattern Field A: C30

ii. Pattern Field B: E30

iii. Pattern Field C: E26

D. Fiber Content: Eco Solution q nylon 100% Dye-injection print.

E. Pile Characteristic: Multi-Level Pattern Cut/loop.

F. Density: 36 oz./cu. yd..

G. Pile Thickness: 0.22 inches.

H. Total Thickness: 0.349 inches I. Stitches: 13 stitches per inch.

J. Gage: 1/10 K. Primary Backing: Woven synthetic.

L. Secondary Backing: Classicbac.

M. Pad: Ultraloc MPC factory applied integral pad.

N. Application: Heavy Traffic.

O. Warranty: 20 year.

P. Roll Width: 12 feet.

Q. Applied Treatments:

1. Applied Soil-Resistance Treatment: Manufacturer's standard material.

Drawings:

1) Sheet A0.01; Delete sheet in its entirety and replace with attached sheet A0.01-r01 – Revised and dated 04/09/2018.

2) C9.5 Detail 16; Extend hatch indicating heated typical reinforced concrete entry pad to include the sidewalk from the north boundary of the ABA parking striping toward the south extending of concrete crosswalk ramp to the Lobby and Registration Wing.

3) Sheets D2.1, D2.2, D2.3, D2.4 and A2.1, A2.2, A2.3, A2.4 Detail 9 all sheets; refer to attached ASK

002 for additional work in Stair S5. All other work to remain as indicated within the documents.

4) Sheets A4.1, A4.2, A4.3, A4.4, and A4.5 – change items below as indicated in all instances:

a. Keynote 2: Revise note to read: “(E) CLAPBOARD SIDING TO REMAIN, PROTECT.

SELECTIVELY PATCH AND REPAIR AS INDICATED OR REQUIRED. PREP AND PAINT

AFFECTED WORK. OPTION B: STRIP, PRIME, AND PAINT ALL EXTERIOR SIDIDING.”

b. Keynote 4; Revise note to read: “(E) HISTORIC CORNICE MOLDING AND FRIEZE BOARD.

OPTION B: STRIP, PRIME AND PAINT ALL EXISTING EXTERIOR TRIM TO REMAIN.”

c. Keynote 5; Revise note to read: “(E) WATER TABLE TRIM. REPLACE (E) BOTTOM SKIRT

BOARD OF (E) WATER TABLE TRIM W/ (N) TO MATCH (E) IN-KIND. PAINT NEW SKIRT

BOARD. OPTION B: STRIP, PRIME AND PAINT ALL EXISTING EXTERIOR TRIM TO REMAIN.”

d. General Notes; Add note 4 reading: “In the event Option B is not selected (requiring the complete striping and refinishing of the exterior of the building), all siding and trims affected by the completion of the work shall be carefully prepared and painted to match in-kind existing such that a fully finished and weather resistant façade shall be created presenting a completely finished building.”

5) Sheet S1.1; Delete sheet in its entirety and replace with attached revised sheet S1.1 R.01 dated

04/09/2018.

6) Sheet S2.1; Change Detail 9 as indicated in the attached sketch SSK #2.

7) Sheet S3.1; Delete sheet in its entirety and replace with attached revised sheet S3.1 R.01 dated

04/09/2018.

8) Sheet S3.2; Delete sheet in its entirety and replace with attached revised sheet S3.2 R.01 dated

04/09/2018.

9) Sheet S5.6; Change Detail 2 as indicated in the attached SSK #1.

10) Sheet M1.0; Delete sheet in its entirety and replace with attached revised sheet M1.0 R.01 dated 04/09/2018.

11) Sheet M2.0. Louvers L-1 and L-2 on the west elevation: interchange louver labels so that louver

L-1 and L-2 locations are substituted for each other.

12) Sheet M3.0; Increase the size of the piping serving P-2 and snowmelt system from 1 ¼” to 1 ½".

13) Sheet M3.1; Delete sheet in its entirety and replace with attached revised sheet M3.1 R.01 dated 04/09/2018.

14) Sheet M4.3; Delete sheet in its entirety and replace with attached revised sheet M4.3 R.01 dated 04/09/2018.

15) Sheet P1.0; Delete sheet its entirety and replace with attached revised sheet P1.0 R.01 dated

04/09/2018.

16) Sheet E1.2; Delete sheet in its entirety and replace with attached revised sheet E1.2 R.01 dated

04/09/2018.

17) Sheet E2.0; Delete sheet in its entirety and replace with attached revised sheet E2.0 R.01 dated

04/09/2018.

END ADDENDUM ONE

RE-FEAD EXISTINGTRANSFORMER ASNEEDED

VICINITY PLANS &

STAGING AREAS 2

A0.01

12 VICINITY PLAN & STAGING AREAS - MAMMOTH HOT SPRINGS, WY - YNP

A0.01 : A0.01 1/64" = 1'-0"14 AREA MAP & STAGING AREAS - MAMMOTH HOT SPRINGS, WY - YNP

A0.01 : A0.01 NOT TO SCALE

MAMMOTH

CHAPEL

MAMMOTH STABLES

NORTH ENTRANCE ROAD

GRAND LOOP ROAD GRAND LOOP ROAD

6.7°

PARK

NATIONAL

YELLOWSTONE

NATIONAL PARK

GRAND TETON

MEMORIAL PARKWAY

J.D. ROCKEFELLER JR.

I D

A

H

O

M

O

N

T A

N

A

JACKSON

WYOMING

MONTANA

W Y

O M

I N

G

I D

A H

O

RIGBY

REXBURG

ST. ANTHONY

CODY

POWELL

UNITED STATES OF AMERICA

VICINITY MAP - YELLOWSTONE NATIONAL PARK

REGIONAL VICINITY MAP

MONTANA

IDAHO

WYOMING

9 YELLOWSTONE NATIONAL PARK - (YNP)

A0.01 : A0.01 NOT TO SCALE

5 LOCATION MAPS

A0.01 : A0.01 NOT TO SCALE

GRAND LOOP ROAD

GRAND LOOP ROAD

PROJECT SITE

GRAND LOOP ROAD

MAMMOTH HOTEL

GRAND LOOP ROAD

MAMMOTH

TERRACE GRILL

JUNIPER DORM

GRAND LOOP ROAD

NORTH ENTRANCE ROAD

BARRACKS ST

BE

AV

ER

P

ON

DS

T

RA

IL

LODGEPOLE AVE

LODGEPOLE AVE

JUNIPER ST

GENERAL

ACCOUNTING

OFFICE

A0.01

6.7°

ONE WAY

NORTH ENTRANCE ROAD

MAMMOTH CABINS

ONE WAY

MAMMOTH

BOILER ROOM

EMPLOYEE

DINING ROOM

MAMMOTH

DINING ROOM

MAMMOTH

CONFERENCE

CENTER

US ENGINEER'S

OFFICE

ASPEN DORM

SPRUCE DORM

LEGEND

HATCH INDICATES APPROXIMATE STAGING & WORK AREA 1

AVAILABLE FOR CONTRACTOR'S USE FROM NOTICE TO

PROCEED THROUGH PROJECT COMPLETION. FINAL EXTENTS

TO BE AGREED TO IN WRITING WITH CONTRACTING OFFICER

BASED ON FIELD COORDINATION.

KEYNOTES#

CONTRACTOR MAY UTILIZE PAVED PARKING AREA INDICATED WITHIN THE

DATE RANGE SPECIFIED. DURING THIS PERIOD CONTRACTOR SHALL

RELEASE AREA FREE OF ALL STORAGE AND CONSTRUCTION DEBRIS FOR

CHAPEL PARKING FOR 1 WEEK PERIOD PRIOR TO AND FOLLOWING

CHRISTMAS DAY AND EASTER.

AT ALL VEGETATED AREAS UTILIZED FOR STAGING, CONTRACTOR

SHALL RESTORE IRRIGATION SYSTEMS, TOP SOIL FERTILITY, AND

RE-VEGITATE TO IN-KIND HISTORIC STATE SUCH THAT NO EVIDENCE

OF USE REMAINS AT PROJECT COMPLETION - TYPICAL.

CONTRACTOR SHALL PROTECT TREE FROM STAGING STORAGE

FROM TRUNK TO DRIP LINE. PROVIDE SAFETY FENCING AT

BOUNDARY TO PREVENT STORAGE.

CONTRACTOR SHALL PLACE STAGGERED DOUBLE LAYER 3/4" PLY-WOOD

PROTECTION WITHIN TREE DRIP LINE WHEN UTILIZING LIFTS OF OTHER

EQUIPMENT TO ACCESS BUILDING FACE.

APPROXIMATE AREA FOR CONTRACTOR STAGING FOR PROJECT

DURATION. CONTRACTOR SHALL COORDINATE EXTENT WITH

CONTRACTING OFFICER AND MAINTAIN SUFFICIENT BUS PARKING AND

VEHICULAR ACCESS AT ALL TIMES.

GENERAL NOTES

1. FIELD VERIFY DIMENSIONS. DO NOT SCALE DRAWINGS. NOTIFY

CONTRACTING OFFICER OF ANY DISCREPANCIES PRIOR TO COMMENCING

WORK.

2. REFER TO ALL DRAWINGS FOR ADDITIONAL INFORMATION AND WORK SCOPE

REQUIRED.

3. MAINTAIN SAFE EGRESS FROM ALL REQUIRED EMERGENCY EXITS

THROUGHOUT CONSTRUCTION.

4. REFERENCE SPECIFICATION SECTION 011216 FOR INITIAL WORK SEQUENCE

AND COORDINATE THE STAGING AREAS DESCRIBED ON THIS SHEET WITH

CONTRACTOR'S PROPOSED PHASING PLAN SUBMITTAL.

HATCH INDICATES APPROXIMATE STAGING & WORK AREA 2

AVAILABLE FOR CONTRACTOR'S USE FROM APPROXIMATELY

10 SEPTEMBER 2018 THROUGH PROJECT COMPLETION. FINAL

EXTENTS TO BE AGREED TO IN WRITING WITH CONTRACTING

OFFICER BASED ON FIELD COORDINATION.

TYP.

TYP.

MAINTAIN VEHICULAR ACCESS ALONG JUNIPER STREET THROUGHOUT

CONSTRUCTION. COORDINATE LIMITED SHUTDOWN FOR UTILITY WORK

AS REQUIRED. MAINTAIN PARKING FOR PUBLIC USE - NO CONTRACTOR

USE ALLOWED.

7 MAINTAIN EMERGENCY EGRESS FROM ENTRANCE/STAIR WHENEVER

BUILDING IS OCCUPIED AND OPEN TO THE PUBLIC.

HATCH INDICATES LIMITS OF WORK AREA 3 AVAILABLE FOR

CONTRACTOR'S WORK FOR TWO PERIODS OF PERFORMANCE.

CONTRACTOR SHALL ENSURE WORK ITEMS REQUIRED ARE

FULLY COMPLETED WITHIN A SINGLE PERIOD.

PERIOD 1 - OCTOBER 15, 2018 THRU DECEMBER 1, 2018.

PERIOD 2 - MARCH 11, 2019 THRU APRIL 20, 2019

P:

\15

1.4

0\D ra wi ng s & M od els

\A uto

CA

D\

B

ID

DI

NG

A

SK

S\

A0 .01

_r 1 V ici nit y P lan

.dw g

A pr

, 2

8 -

:44 am

15021.40

MAMMOTH HOTEL PHASE II

GUEST WING RENOVATION

NATIONAL PARK SERVICE - US DEPARTMENT OF THE INTERIOR

MAMMOTH HOT SPRINGS, WY - YELLOWSTONE NATIONAL PARK

YELL 101

135239

30402.28.2018

PKG 1

0 1 2 3 4 5 6 7 8 9 10 inches

PROJECT NO:

DESIGNED

CADD

TECH. REVIEW

DATE

SUB SHEET NO. DRAWING NO.

PKG.

NO.

SHEET

OF

TITLE OF SHEET

REVISIONS

CO

NS

TR

UC

TI

ON

D

OC

UM

EN

TS

PMIS NO. 205796

L

I

C

E

N

S

E

D

AR

C

H

I

T

E

C

T

S

T

A

T

E

O

F W

Y

O

M

I

N

G

04.09.20181

R. 01

RE

VI

SI

ON

AutoCAD SHX Text

BLDG.

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

YELLOWSTONE

AutoCAD SHX Text

HEART

AutoCAD SHX Text

LAKE

AutoCAD SHX Text

LEWIS

AutoCAD SHX Text

LAKE

AutoCAD SHX Text

SHOSHONE

AutoCAD SHX Text

LAKE

AutoCAD SHX Text

DELUSION

AutoCAD SHX Text

LAKE

AutoCAD SHX Text

CONTINENTAL

AutoCAD SHX Text

DIVIDE

AutoCAD SHX Text

CONTINENTAL DIVIDE

AutoCAD SHX Text

PARK

AutoCAD SHX Text

TETON

AutoCAD SHX Text

COUNTY

AutoCAD SHX Text

COUNTY

AutoCAD SHX Text

GRANT

AutoCAD SHX Text

VILLAGE

AutoCAD SHX Text

WEST

AutoCAD SHX Text

THUMB

AutoCAD SHX Text

OLD

AutoCAD SHX Text

FAITHFUL

AutoCAD SHX Text

BRIDGE

AutoCAD SHX Text

BAY

AutoCAD SHX Text

FISHING

AutoCAD SHX Text

BRIDGE

AutoCAD SHX Text

PARK COUNTY

AutoCAD SHX Text

TETON COUNTY

AutoCAD SHX Text

WEST

AutoCAD SHX Text

YELLOWSTONE

AutoCAD SHX Text

MADISON

AutoCAD SHX Text

NORRIS

AutoCAD SHX Text

CANYON

AutoCAD SHX Text

GARDINER

AutoCAD SHX Text

EAST

AutoCAD SHX Text

ENTRANCE

AutoCAD SHX Text

NORTH EAST

AutoCAD SHX Text

ENTRANCE

AutoCAD SHX Text

SOUTH

AutoCAD SHX Text

ENTRANCE

AutoCAD SHX Text

WEST

AutoCAD SHX Text

ENTRANCE

AutoCAD SHX Text

IDAHO

AutoCAD SHX Text

WYOMING

AutoCAD SHX Text

WYOMING

AutoCAD SHX Text

MONTANA

AutoCAD SHX Text V.C.

AutoCAD SHX Text V.C.

AutoCAD SHX Text V.C.

AutoCAD SHX Text V.C.

AutoCAD SHX Text

PELICAN

AutoCAD SHX Text

CONE

AutoCAD SHX Text

LAMAR

AutoCAD SHX Text

RIVER

AutoCAD SHX Text

TOWER-

AutoCAD SHX Text

ROOSEVELT

AutoCAD SHX Text V.C.

AutoCAD SHX Text

NORTH

AutoCAD SHX Text

ENTRANCE

AutoCAD SHX Text

RIVER

AutoCAD SHX Text

GALLATIN

AutoCAD SHX Text

MONTANA

AutoCAD SHX Text

WYOMING

AutoCAD SHX Text

MAMMOTH

AutoCAD SHX Text

HOT SPRINGS

AutoCAD SHX Text

COOKE

AutoCAD SHX Text

CITY

AutoCAD SHX Text

MONTANA

AutoCAD SHX Text

IDAHO

AutoCAD SHX Text

LAKE

AutoCAD SHX Text

SNAKE

AutoCAD SHX Text

RIVER

AutoCAD SHX Text

BECHLER

AutoCAD SHX Text

RIVER

AutoCAD SHX Text

MT. HOLMES

AutoCAD SHX Text

MT. SHERIDAN

AutoCAD SHX Text

GALLATIN

AutoCAD SHX Text

NATIONAL

AutoCAD SHX Text

FOREST

AutoCAD SHX Text

TARGHEE

AutoCAD SHX Text

NATIONAL

AutoCAD SHX Text

FOREST

AutoCAD SHX Text

TETON

AutoCAD SHX Text

NATIONAL

AutoCAD SHX Text

FOREST

AutoCAD SHX Text

SHOSHONE

AutoCAD SHX Text

NATIONAL

AutoCAD SHX Text

FOREST

AutoCAD SHX Text

GALLATIN NATIONAL FOREST

AutoCAD SHX Text

BECHLER

AutoCAD SHX Text

TOWER

AutoCAD SHX Text

FALL

AutoCAD SHX Text

SLOUGH

AutoCAD SHX Text

CREEK

AutoCAD SHX Text

PEBBLE

AutoCAD SHX Text

CREEK

AutoCAD SHX Text

WAPITI LAKE

AutoCAD SHX Text

WHITE

AutoCAD SHX Text

LAKE

AutoCAD SHX Text

AutoCAD SHX Text

HEBGEN

AutoCAD SHX Text

LAKE

AutoCAD SHX Text

TO

AutoCAD SHX Text

ASHTON

AutoCAD SHX Text

TO

AutoCAD SHX Text

BOZEMAN

AutoCAD SHX Text

TO LIVINGSTON

AutoCAD SHX Text

INDIAN

AutoCAD SHX Text

CREEK

AutoCAD SHX Text

GREBE

AutoCAD SHX Text

LAKE

AutoCAD SHX Text

CASCADE

AutoCAD SHX Text

LAKE

AutoCAD SHX Text

ICE

AutoCAD SHX Text

LAKE

AutoCAD SHX Text

MARY

AutoCAD SHX Text

LAKE

AutoCAD SHX Text

TO GRAND TETON NATIONAL PARK

AutoCAD SHX Text

TO CODY,

AutoCAD SHX Text

WYOMING

AutoCAD SHX Text

TO

AutoCAD SHX Text

RED LODGE,

AutoCAD SHX Text

MONTANA

AutoCAD SHX Text

, MONTANA

AutoCAD SHX Text

YELLOWSTONE

AutoCAD SHX Text

RIVER

AutoCAD SHX Text

GRIZZLY

AutoCAD SHX Text

LAKE

AutoCAD SHX Text

SILVER

AutoCAD SHX Text

GATE

AutoCAD SHX Text

AutoCAD SHX Text

GALLATIN CO.

AutoCAD SHX Text

FREMONT CO.

AutoCAD SHX Text

PARK HQ

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

LAKE

AutoCAD SHX Text

HOTEL

AutoCAD SHX Text

BLDG.

AutoCAD SHX Text

A & E ARCHITECTS P.C.

AutoCAD SHX Text

JAMES R. MCDONALD

AutoCAD SHX Text

WYOMING

AutoCAD SHX Text

MISSOULA

AutoCAD SHX Text C-1435

RE

VI

SI

ON

R. 01

SI

ON

SI

ON

M1.0

MECHANICAL LEGENDS AND

SCHEDULES

0 1 2 3 4 5 6 7 8 9 10 inches

DESIGNED

CADD

TECH. REVIEW

DATE

SUB SHEET NO. DRAWING NO.

PKG.

NO.

SHEET

OF

TITLE OF SHEET

C O

N S

T R

U C

T

IO

N D

O C

U M

E N

T S

YELL 101

135239

30402.28.2018

PKG 1

101 E. BROADWAY

BELGRADE, MT 59714

PH: (406) 388-3320

FAX: (406) 388-3389

ACE PROJECT #: 13BZ4199.005

PROJECT NO:

REVISIONS:

PMIS NO. 205796

15021.40

MAMMOTH HOTEL PHASE II

GUEST WING RENOVATION

NATIONAL PARK SERVICE - US DEPARTMENT OF THE INTERIOR

MAMMOTH HOT SPRINGS, WY - YELLOWSTONE NATIONAL PARK

04.09.20181

DUCTWORK CONST. SCHED.

MECHANICAL SYMBOLS LEGEND

THIS IS A STANDARDIZED SYMBOLS LEGEND, ALL SYMBOLS SHOWN MAY NOT

APPEAR ON OR WITHIN THIS SET OF CONTRACT DOCUMENTS.

- ALL INTERIOR SUPPLY DUCTWORK

- ALL EXHAUST DUCTWORK FROM THE BACKDRAFT DAMPER TO THE EXTERIOR

- ALL FRESH AIR DUCTWORK AND COMBUSTION AIR DUCTWORK

- ALL OTHER INTERIOR EXHAUST DUCTWORK

- ALL INTERIOR RETURN DUCTWORK

- ALL TRANSFER DUCTWORK

INSULATED FLEXIBLE DUCTWORK MAY BE USED AT THE CONTRACTOR'S OPTION FOR A

MAXIMUM OF 5 FT. LENGTH TO EACH DIFFUSER/REGISTER/ GRILLE.

LINED DUCTWORK INCLUDES:

UNINSULATED/UNLINED DUCTWORK INCLUDES:

INSULATED DUCTWORK INCLUDES:

18"Ø or 18"

LPS

C

HWR

HWS

HOT WATER

RETURN

HOT WATER

SUPPLY

LOW PRESS.

STEAM

CONDENSATE

LINE

DOUBLE LINE

REPRESENTATION

SINGLE LINE

REPRESENTATION

DOUBLE LINE

REPRESENTATION

SINGLE LINE

REPRESENTATION

P.O.C.-POINT OF

CONNECTION

SWITCH

T'STAT. (ELEC.)

SIDEWALL AIR DEVICE

WALL LOUVER

NEW EQUIPMENT

EXISTING TO REMAIN

DRAWING LIST

M1.0 MECHANICAL LEGENDS AND SCHEDULES M2.3 THIRD FLOOR HVAC PLAN

MD3.0 CRAWLSPACE HYDRONIC DEMOLITION PLAN M2.4 FOURTH FLOOR HVAC PLAN

MD3.1 FIRST FLOOR HYDRONIC DEMOLITION PLAN M2.5 ATTIC HVAC PLAN

MD3.2 SECOND FLOOR HYDRONIC DEMOLITION PLAN M3.0 CRAWLSPACE HYDRONIC PLAN

MD3.3 THIRD FLOOR HYDRONIC DEMOLITION PLAN M3.1 FIRST FLOOR HYDRONIC PLAN

MD3.4 FOURTH FLOOR HYDRONIC DEMOLITION PLAN M3.2 SECOND FLOOR HYDRONIC PLAN

MD3.5 ATTIC MECHANICAL DEMOLITION PLAN M3.3 THIRD FLOOR HYDRONIC PLAN

MD4.3

BASEMENT AND SECOND FLOOR HYDRONIC

DEMOLITION PLAN - EXISTING BUILDING

M3.4 FOURTH FLOOR HYDRONIC PLAN

M2.0 CRAWLSPACE HVAC PLAN M4.1 MECHANICAL DETAILS

M2.1 FIRST FLOOR HVAC PLAN M4.2 MECHANICAL DETAILS II

M2.2 SECOND FLOOR HVAC PLAN M4.3

BASEMENT AND SECOND FLOOR HYDRONIC

PLAN - EXISTING BUILDING

EXHAUST FAN SCHEDULE

PLAN CODE MANUFACTURER

MODEL

NUMBER

CFM ESP RPM

DRIVE

TYPE

ELECTRICAL DATA

REMARKS

HP VOLT AMP PH

EF-1 COOK 150SQN17D (VF) 2500 0.5 1725 EC 5/8 120 13 1 SEE NOTES BELOW

EF-2 COOK 165SQN17D (VF) 3300 0.5 1725 EC 1 208 8 1 SEE NOTES BELOW

EF-3 COOK 165SQN17D (VF) 3800 0.5 1725 EC 1 1/2 208 10 1 SEE NOTES BELOW

NOTES:

1. PROVIDE FANS WITH BACKDRAFT DAMPER, REMOTE SPEED CONTROLLER, AIR BALANCE KIT, FACTORY PRE-WIRED DISCONNECT AND FLEXIBLE INLET/OUTLET CONNECTORS. TC CONTRACTOR RESPONSIBLE FOR LOW

VOLTAGE CONNECTIONS AND CONDUIT. CONNECT FANS TO EXISTING BUILDING AUTOMATION SYSTEM.

2. SUSPEND FANS FROM ROOF STRUCTURE WITH VIBRATION SPRING ISOLATORS.

FINNED PIPE RADIATION SCHEDULE

PLAN

CODE

MANUF.

MODEL

NUMBER

ENCLOSURE PERFORMANCE

ROW LENGTH DEPTH HEIGHT TYPE MOUNT HEIGHT MBH GPM EWT °F

TEMP

CHANGE °F

FT-1 RUNTAL RF-3 3 10' 1.6" 8.6" STEEL 3" AFF 7.90 1 180 20 PROVIDE END CAPS

FT-2 RUNTAL RF-3 3 9' 1.6" 8.6" STEEL 3" AFF 7.11 0.5 180 20 PROVIDE END CAPS

FT-3 RUNTAL RF-3 3 4' 1.6" 8.6" STEEL 3" AFF 3.16 0.5 180 20 PROVIDE END CAPS

NOTES:

1. ARCHITECT TO SELECT COLOR FROM STANDARD COLOR CHART. ALL BRACKETS, HARDWARE AND FASTENERS SHALL MATCH THE COLOR OF THE RADIATOR.

2. INSTALL WITH HANGING BOARD PER DETAIL 1/M4.1. PROVIDE TACO ZONE SENTRY HOT WATER 2-WAY CONTROL VALVE (OR EQUIVALENT VALVE FOR INSTALLATION IN TIGHT ENCLOSURES) AND ISOLATION VALVE BEHIND END CAP OF PANEL. PROVIDE PANEL WITH SAME SIDE INLET AND OUTLET CONFIGURATION. PROVIDE CUSTOM END CAPS TO COVER PIPING FROM UNIT TO WALL.

3. SEE ARCHITECTURAL ELEVATIONS FOR RADIATOR MOUNTING HEIGHTS. SEE DETAIL 1/M4.1 FOR PANEL INSTALLATION REQUIREMENTS.

HYDRONIC SIZING

SIZE GPM

3/4" 2.5

1" 6

1 1/4" 10

1 1/2" 17

2" 35

2 1/2" 65

3" 105

4" 320

ELEVATION NOTES

THE BUILDING SITE IS LOCATED IN MAMMOTH, WY. AT

APPROXIMATELY 6,300' ELEVATION. ACCOUNT FOR THIS

ELEVATION IN ALL EQUIPMENT SELECTIONS.

TEMPERATURE CONTROLS NOTES

MODIFY EXISTING HEAT EXCHANGER DISCHARGE WATER TEMPERATURE TO 180°F. HEAT EXCHANGERS LOCATED IN EXISTING MECHANICAL ROOM.

ALL THERMOSTATS IN PUBLIC SPACES (CORRIDORS, STAIR TOWERS, ELEVATOR LOBBY) AND OFFICE SPACES (LOCATION MANAGER, TIMEKEEPING/STAFF LOCKERS, OFFICE ASSISTANT, HOUSEKEEPING OFFICE, AND DOCK INTAKE) SHALL BE WIRED 24V NETWORK THERMOSTATS WITH DIGITAL DISPLAY TO TIE INTO THE BUILDING AUTOMATION SYSTEM. COORDINATE WITH E.C. FOR POWER TO RADIANT HEATER CONTROL PANELS IN

CRAWLSPACE AND ATTIC. PROVIDE WITH JCI T701DFP-4 THERMOSTAT OR EQUIVALENT 24V WIRED NETWORK THERMOSTAT.

ALL THERMOSTATS IN PUBLIC GUEST ROOMS AND ASSOCIATED BATHROOMS SHALL BE WIRED 120V STAND ALONE THERMOSTATS WITH DIGITAL DISPLAY. ALL HOT WATER RADIATOR CONTROL VALVES IN GUEST ROOMS AND ASSOCIATED BATHROOMS SHALL BE 120V VALVES. PROVIDE WITH

TACO ZONE SENTRY SERIES VALVE AND AUBE TH114-A THERMOSTAT OR EQUIVALENT 120V NON-PROGRAMMABLE, STAND-ALONE THERMOSTAT.

PROVIDE METER FOR ALL UTILITIES TO BE TIED INTO BUILDING AUTOMATION SYSTEM. METERED UTILITIES SHALL INCLUDE ELECTRIC SERVICE, DOMESTIC COLD WATER, DOMESTIC HOT WATER, AND GAS SERVICE.

T.C. RESPONSIBLE FOR ALL LOW VOLTAGE WIRING, CONDUIT, AND TERMINATIONS. E.C. RESPONSIBLE FOR THERMOSTAT ROUGH-IN.

DESIGN BASIS CODES

2015 INTERNATIONAL BUILDING CODE

2015 INTERNATIONAL MECHANICAL CODE

2015 INTERNATIONAL ENERGY CONSERVATION CODE

2015 INTERNATIONAL FIRE CODE

2015 INTERNATIONAL FUEL GAS CODE

HOT WATER UNIT HEATER SCHEDULE

PLAN CODE MANUFACTURER

MODEL

NUMBER

CFM

(100°)

MBH

INPUT

GPM MBH OUTPUT

ELECTRICAL DATA

REMARKS

RPM FLA HP VOLT PH

UH-1, 2, 3 STERLING HS-136A 750 18.4 2 18.4 900 1.4 1/20 120 1 SEE NOTES BELOW

NOTES:

1. INSTALL PER MANUFACTURER'S RECOMMENDATIONS.

2. PROVIDE WITH THERMOSTAT AND 3-WAY HOT WATER CONTROL VALVE. SEE DETAIL 10/M4.1 FOR MORE DETAILS.

3. ARCHITECT TO SELECT COLOR FROM STANDARD COLOR CHART.

ENERGY RECOVERY VENTILATOR SCHEDULE

PLAN

CODE

MANUF.

MODEL

NUMBER

SUPPLY AND EXHAUST SECTION ELECTRICAL DATA FILTER

REMARKS

FAN CFM E.S.P. HP VOLT PH AMPS WATTS TYPE

ERV-1 RENEWAIRE HE1.5XINV 900 1 1 208 1 8 1500 MERV 13 SEE NOTES BELOW

ERV-2 RENEWAIRE HE1.5XINV 600 1 1 208 1 8 1500 MERV 13 SEE NOTES BELOW

NOTES: 1. PROVIDE WITH SINGLE POINT POWER CONNECTION, FUSED DISCONNECT, DOUBLE WALL CONSTRUCTION, MERV 13 FILTERS, FACTORY MOUNTED FILTER ALARM, BMS INTEGRATION, AND MOTORIZED

ISOLATION DAMPERS ON OA AND EA. TC CONTRACTOR RESPONSIBLE FOR LOW VOLTAGE CONNECTIONS AND CONDUIT.

2. EXCAVATE AROUND UNIT TO PROVIDE ACCESS FOR MAINTENANCE AND DUCT ROUTING. PROVIDE NEW FILTER AT UPON SUBSTANTIAL COMPLETION.

3. PROVIDE HOT WATER COILS IN SUPPLY AIR DUCTS. SEE ERV COIL SCHEDULE FOR MORE INFORMATION.

1. THE INTENT OF THESE DRAWINGS IS TO REMOVE ALL EXISTING MECHANICAL AND HYDRONIC

EQUIPMENT LOCATED IN THE BUILDING GUEST WING.

2. CONTRACTING OFFICER HAS FIRST RIGHT OF REFUSAL FOR ALL EQUIPMENT/MATERIAL CALLED

OUT TO BE REMOVED. CONTRACTOR SHALL PRESENT ALL DEMO'D EQUIPMENT/MATERIAL TO

CONTRACTING OFFICER PRIOR TO REMOVING FROM SITE. COORDINATE WITH LIST OF ITEMS TO

BE SALVAGED.

DEMOLITION NOTES

GRAVITY VENTILATOR SCHEDULE

PLAN

CODE

MANUF.

MODEL

NUMBER

FUNCTION HOOD SIZE

THROAT

SIZE

MATERIAL FINISH CFM DAMPER REMARKS

GV-1 COOK TRE INTAKE 35 3/4" X 35 3/4" X 9" 24" X 24" ALUMINUM BLACK SEE PLANS MOTORIZED SEE BELOW

GV-2 COOK TRE EXHAUST 35 3/4" X 47 3/4" X 12 1/2" 24" X 36" ALUMINUM BLACK SEE PLANS MOTORIZED SEE BELOW

GV-3 COOK TRE EXHAUST 35 3/4" X 47 3/4" X 16" 24" X 36" ALUMINUM BLACK SEE PLANS MOTORIZED SEE BELOW

GV-4 COOK TRE EXHAUST 35 3/4" X 47 3/4" X 16" 24" X 36" ALUMINUM BLACK SEE PLANS MOTORIZED SEE BELOW

NOTES:

1. PROVIDE WITH BIRD SCREEN AND PRE-MANUFACTURED 14" ROOF CURB. MATCH TAN COLOR OF GRAVITY VENTILATORS ON EXISTING BUILDING.

2. PROVIDE ALL VENTILATORS WITH MOTORIZED DAMPER. DAMPER SIZE SHALL BE THE SAME AS THROAT SIZE. TC CONTRACTOR RESPONSIBLE FOR LOW VOLTAGE

CONNECTIONS AND CONDUIT.

RADIANT SNOWMELT SCHEDULE (35% PROPYLENE GLYCOL)

PLAN

CODE

MANUF.

TUBE

SPACING

SUPPLY

TEMP. MAX

HWS

TEMP

HWR

TEMP

FT. OF

HEAD

GPM

HEADER

SIZE

TUBE

SIZE

# OF

CIRC.

LOAD

MBH

ZONE

SQ. FT.

REMARKS

SM-1

REHAU-

PEX

6" O.C. 95 92 72 10.0 11.00 1 1/4" 1" 5 129.0 768

MAXIMUM CIRCUIT

LENGTHS 300'

SM-2

REHAU-

PEX

6" O.C. 98 94 74 10.0 23.00 1 1/4" 1" 12 265.9 1583

MAXIMUM CIRCUIT

LENGTHS 300'

NOTES:

1. VERIFY EXACT RADIANT PANEL LOCATION WITH G.C. PRIOR TO INSTALL. INSTALL CONTROLLERS IN CRAWLSPACE ELECTRICAL ROOM.

2. PROVIDE MANIFOLD W/ CIRCUIT ISOLATION VALVES ON SUPPLY AND RETURN, CIRCUIT FLOW INDICATORS, VENT AND PURGE ASSEMBLY, AND PRESSURE GAUGES.

3. PROVIDE TEMPERATURE MIXING VALVE BEFORE MANIFOLD TO DECREASE WATER TEMP TO 95°F.

3. M.C. TO PROVIDE SENSORS, ALL LOW VOLTAGE CONTROL DEVICES, CONDUCTORS AND TERMINATIONS.

4. SUPPLIER TO PROVIDE RADIANT HEAT PIPING LAYOUT FOR REVIEW DURING SHOP DRAWING PROCESS.

5. PROVIDE AND INSTALL IN-SLAB SNOW MELT SENSOR AND WIRE TO DDC SYSTEM FOR CONTROL OF SNOW MELT ZONES. TIE INTO EXISTING BUILDING MANAGEMENT SYSTEM.

GRILLE - REGISTER - DIFFUSER SCHEDULE

PLAN

CODE

MANUFACTURER MODEL NUMBER FUNCTION NECK SIZE MATERIAL FINISH CFM

VOLUME

DAMPER

REMARKS

EG-1 KRUEGER S80 EXHAUST 6" X 6" STEEL BAKED ENEMEL SEE PLANS IN DUCT 6" X 6" WALL GRILLE

EG-2 KRUEGER 6490 EXHAUST 6" X 6" STEEL BAKED ENEMEL SEE PLANS IN DUCT 12" X 12" CEILING GRILLE

RG-1 KRUEGER S80 RETURN 6" X 6" STEEL BAKED ENEMEL SEE PLANS IN DUCT 6" X 6" WALL GRILLE

SG-1 KRUEGER S80 SUPPLY 6" X 6" STEEL BAKED ENEMEL SEE PLANS IN DUCT 6" X 6" WALL GRILLE

NOTES:

1. PROVIDE ALL DUCT TRANSITIONS TO AND FROM GRILLES/REGISTERS/DIFFUSERS AS REQUIRED.

2. CONTRACTOR SHALL VERIFY EXACT BUILDING CONSTRUCTION AND CEILING TYPES AND PROVIDE THE CORRECT FRAMES FOR ALL AIR DIFFUSION PRODUCTS AS REQUIRED.

3. PROVIDE MANUAL VOLUME DAMPERS FOR CONNECTION TO ALL GRD'S. PROVIDE MANUAL VOLUME DAMPERS WITH 2" STAND-OFF BRACKETS.

4. PROVIDE EXTENDED LINKAGE FROM HAND DAMPER TO A FLUSH CUP DAMPER REGULATOR IN ALL HARD CEILING LOCATIONS (HARD INACCESSIBLE CEILINGS. REFER TO ARCHITECTURAL REFLECTED CEILING PLANS FOR ALL TYPES OF CEILINGS.

5. SEE DRAWINGS FOR FURTHER GRD REQUIREMENTS.

LOUVER SCHEDULE

PLAN CODE MANUF. MODEL NUMBER FUNCTION SIZE

FREE

AREA VEL.

PRES DROP MATERIAL FINISH CFM DAMPER REMARKS

L-1 RUSKIN ELF6375DX EXHAUST 39" X 12" 787 0.08 ALUMINUM ARCHITECT SELECTED SEE PLANS BACKDRAFT SEE NOTES BELOW

L-2 RUSKIN ELF6375DX EXHAUST 27" X 12" 776 0.07 ALUMINUM ARCHITECT SELECTED SEE PLANS BACKDRAFT SEE NOTES BELOW

NOTES: 1. PROVIDE EACH LOUVER WITH A MOTORIZED DAMPER. COORDINATE WITH EC ON INSTALLATION. TC CONTRACTOR RESPONSIBLE FOR LOW VOLTAGE CONNECTIONS AND CONDUIT.

2. SLOPE BOTTOM OF DUCT TOWARDS LOUVER CONNECTION. SEE DETAIL 11/M4.1 FOR MORE DETAILS.

HISTORIC HOT WATER RADIANT HEATER SCHEDULE

PLAN

CODE

MANUF.

MODEL

NUMBER

ENCLOSURE PERFORMANCE

REMARKS

SECTIONS SIZE (L/W/H) BTU GPM EWT °F TEMP CHANGE °F

HRP-1 BURNHAM

SLENDERIZED

19-4 14 24 12" / 4 7

16" / 19" 3808 0.5 180 20

HISTORIC BATHROOM

HEATER

HRP-2 BURNHAM

SLENDERIZED

25-6 18 31 12" / 6 15

16" / 25" 9180 1 180 20 ELEVATOR LOBBY HEATER

HRP-3 BURNHAM

SLENDERIZED

25-6 26 45 12" / 6 15

16" / 25" 13260 1.5 180 20

STAIRWELL / CORRIDOR

HEATER

HRP-4 BURNHAM

SLENDERIZED

25-6 16 28" / 6 15

16" / 25" 8160 1 180 20 SUITE 419 HEATER

NOTES:

1. ROUTE PIPING THROUGH FLOOR JOISTS AND UP THROUGH FLOOR TO RADIATOR. TRANSITION TO SCHEDULE 40 STEEL WITH DIELECTRIC NIPPLE UNDER FLOOR AND CLAMP

SCHEDULE 40 PIPE TO FLOOR. SEE DETAIL 6/M4.1 FOR MORE INFORMATION.

2. PROVIDE WITH BOTTOM SUPPLY AND RETURN CONNECTIONS. SEE DETAIL 6/M4.1 FOR PIPE MATERIALS AND REQUIREMENTS.

3. PROVIDE HOT WATER 2-WAY CONTROL VALVE AND ISOLATION VALVE IN WALL NEAR UNIT BEHIND ACCESS PANEL.

ERV COIL SCHEDULE

PLAN

CODE

MANUF. MODEL NUMBER FUNCTION

ELEMENT DATA AIR SIDE LIQUID SIDE

SENS

HTG MBHTYPE ROW

LENGTH

(IN)

HEIGHT

(IN)

F.V.

FPM

CFM

PD, IN

W.C.

EAT

DB

LAT

DB

GPM

PD, FT

H2O

EWT

°F

LWT °F

HWC-1 TEMTROL 5WC-8-12x14x2-9AL TEMPER HRV AIR HW 2 14 12 771 900 0.33 55 98.4 3.7 0.8 180 160 34.6

HWC-2 TEMTROL 5WC-16-12x12x2-6AL TEMPER HRV AIR HW 2 12 12 514 600 0.10 55 98.2 2.4 2.6 180 160 23.0

NOTES:

1. PROVIDE 2 WAY CONTROL VALVE AT PIPE CONNECTION. SEE DETAIL 2/M4.2 FOR PIPING CONNECTION DETAILS.

2. PROVIDE FREEZESTAT IN DUCT DOWN STREAM OF COIL.

PUMP SCHEDULE (35% PROPYLENE GLYCOL)

PLAN

CODE

MANUF.

MODEL

NUMBER

SIZE RPM GPM FT OF HD

ELECTRICAL DATA

REMARKS

HP VOLT AMP PH

P-1 TACO 0010-F3 1 1/2" X 1 1/2" 3250 23 10 1/8 115 1.10 1

SEE NOTES

BELOW

P-2 TACO 007-F5 1 1/4" X 1 1/4" 3250 11 10 1/25 115 0.74 1

SEE NOTES

BELOW

NOTES:

1. RADIANT SNOW MELT PUMP. CAST IRON CASING, STAINLESS STEEL CARTRIDGE PUMP. PUMP SEALS SHALL BE COMPATIBLE WITH PROPYLENE GLYCOL. CONNECT PUMPS TO

EXISTING BUILDING AUTOMATION SYSTEM.

GENERAL NOTES

1. THE CONTRACTING OFFICER HAS THE RIGHT OF REFUSAL FOR ANY SALVAGED MATERIALS AND EQUIPMENT. IF MATERIALS OR EQUIPMENT

ARE REFUSED BY THE CONTRACTING OFFICER, THE GENERAL CONTRACTOR SHALL ASSUME RESPONSIBILITY TO DISPOSE OF THE EQUIPMENT.

2. CONTRACTOR RESPONSIBLE FOR PROVIDING LAMINATED VALVE CHARTS FOR ALL VALVES INSTALLED IN PROJECT UPON SUBSTANTIAL

COMPLETION.

FIRE/SMOKE DAMPER NOTES

1) PROVIDE WITH 120V ACTUATORS.

2) PROVIDE ALL FIRE/SMOKE DAMPERS WITH REMOTE SWITCH

PACKAGE.

RE

VI

SI

ON

M3.1

FIRST FLOOR HYDRONIC PLAN

0 1 2 3 4 5 6 7 8 9 10 inches

DESIGNED

CADD

TECH. REVIEW

DATE

SUB SHEET NO. DRAWING NO.

PKG.

NO.

SHEET

OF

TITLE OF SHEET

C O

N S

T R

U C

T

IO

N D

O C

U M

E N

T S

YELL 101

135239

30402.28.2018

PKG 1

101 E. BROADWAY

BELGRADE, MT 59714

PH: (406) 388-3320

FAX: (406) 388-3389

ACE PROJECT #: 13BZ4199.005

PROJECT NO:

REVISIONS:

PMIS NO. 205796

15021.40

MAMMOTH HOTEL PHASE II

GUEST WING RENOVATION

NATIONAL PARK SERVICE - US DEPARTMENT OF THE INTERIOR

MAMMOTH HOT SPRINGS, WY - YELLOWSTONE NATIONAL PARK

KEY PLAN

04.09.20181

U P

U P

D N

U P

D N

U P

D N

6.1

6.2

6.3

RRPP

JJGG

EE

A.1

BB

DD FF NN QQKK

5.1

5.2

HH

A.2

CC MMLL

B.1

A

B

GENERAL HYDRONIC NOTES:

KEY HYDRONIC NOTES:

INSTALL FREE STANDING RADIATOR AT APPROXIMATE LOCATION. ROUTE HWS/HWR THROUGH CHASE AND CONNECT AS REQUIRED. INSTALL BALANCE AND ISOLATION VALVE BEHIND ACCESS PANEL IN CHASE.

ROUTE HWS/HWR UP FROM CRAWLSPACE BELOW TO SNOW MELT MANIFOLD AT APPROXIMATE LOCATION SHOWN. PROVIDE ACCESS DOOR IN WALL WITH LOCKING COVER TO ACCESS VALVES.

ROUTE SNOW MELT PIPING THROUGHOUT DOCK IN DASHED AREA AS SHOWN. ROUTE PIPING UNDERNEATH METAL STAIRCASE WITHIN DASHED REGION.

ROUTE SNOW MELT PIPING THROUGHOUT ENTRANCE AND UNDER OVERHANG IN DASHED AREA AS SHOWN. CONTINUE PIPING DOWN SIDEWALK TO CROSSWALK. INSTALL ALL VALVES AND ACCESSORIES BEHIND ACCESS PANEL

LOCATED IN LINEN STORAGE 125.

ROUTE HWS/HWR THROUGH JOIST SPACE AND UP THROUGH FLOOR AT LOCATIONS SHOWN. CONTINUE PIPING TO UH-1 AS SHOWN AND CONNECT AS REQUIRED.

ROUTE HWS/HWR UP IN WALL AND TEE OFF TO EACH RADIANT PANEL AS REQUIRED. INSTALL BALANCE AND ISOLATION VALVES BEHIND PANEL END CAP. PROVIDE END CAP TO COVER EXPOSED PIPING FROM WALL TO PANEL.

CONTINUE HWS/HWR PIPING UP TO FLOOR ABOVE.

SEE ELECTRICAL SHEETS FOR ELECTRIC HEATER LOCATIONS ABOVE BATHROOM DOOR. COORDINATE WITH E.C. FOR INSTALLATION.

MOUNT UNIT HEATER AT APPROXIMATE LOCATION PER MANUFACTURERS RECOMMENDATION.

INSTALL RADIANT PANEL HEATER ON WALL AT APPROXIMATE LOCATION PER MANUFACTURER'S RECOMMENDATION. INSTALL ISOLATION AND BALANCE VALVE BEHIND PANEL END CAP.

ROUTE HWS/HWR THROUGH JOIST SPACE AND THROUGH FLOOR TO EACH RADIANT PANEL. PROVIDE COVER FOR PIPING ALONG WALL. CONTINUE PIPING UP IN WALL TO CEILING SPACE AND ROUTE OVER TO LOCATIONS SHOWN

AND ROUTE UP IN WALL ON FLOOR ABOVE. SEE DETAIL 13/M4.1 FOR MORE INFO. INSTALL ALL VALVES BEHIND PANEL COVER.

ROUTE 3/4" HWS/HWR RETURN UP FROM CRAWLSPACE THROUGH FLOOR TO RADIATOR. CONNECT TO RADIATOR AS REQUIRED. INSTALL BALANCE AND ISOLATION VALVES IN CRAWLSPACE.

ROUTE HWS/HWR PIPING UP IN WALL AS SHOWN FROM CRAWLSPACE TO FIRST FLOOR. ROUTE PIPING THROUGH JOISTS AND CONTINUE PIPING UP TO FLOOR ABOVE. SEE M3.2 FOR PIPE CONTINUATION.

ROUTE 3/4" HWS/HWR UP THROUGH SLAB TO RADIATOR AT APPROXIMATE LOCATION. CONNECT TO RADIATOR PER MANUFACTURERS RECOMMENDATION.

ROUTE HWS/HWR UP FROM BASEMENT TO JOIST SPACE AND OVER TO LOCATION SHOWN AND UP IN WALL ABOVE. TEE OFF FOR RADIANT PANEL ON FIRST FLOOR AND PROVIDE COVER FOR EXPOSED PIPING. INSTALL ALL VALVES

BEHIND RADIANT PANEL COVER.

INSTALL HRP-3 ON BOTTOM LANDING OF STAIRWELL AT APPROXIMATE LOCATION. ROUTE PIPING FROM CRAWLSPACE THROUGH VESTIBULE WALL TO RADIATOR. INSTALL BALANCE AND ISOLATION VALVES IN CRAWLSPACE.

ROUTE 1" HWS/HWR PIPING THROUGH JOISTS AND UP IN WALL ABOVE. SEE M3.2 FOR PIPING CONTINUATION.

INSTALL TEKMAR 090-091 RADIANT SNOW MELT SENSOR IN CONCRETE AT APPROXIMATE LOCATION. CONNECT SENSOR TO RADIANT SNOW MELT CONTROLS IN CRAWLSPACE.

PROVIDE LOCKING COVER FOR THERMOSTAT AT APPROXIMATE LOCATION.

ROUTE SNOW MELT PIPING THROUGHOUT EXISTING BUILDING ENTRY IN DASHED AREA AS SHOWN. CONTINUE PIPING AROUND PATIO OF SKI SHOP. SEE DETAIL 13/M4.2 FOR SNOW MELT PIPING EXTENTS.

FT

FT

FT

FT

FT

FT

FT

FT

FT

FT

FT

FT

FT

FT

FT

FT

FT

FT

2FT

FT

HRP

HRP

FT

HRP

1FT

UH

6 6 6 6 66 6 6

6 6 6 66

9 FIRST FLOOR HYDRONIC PLAN

MD3.1 : M3.1 1/8" = 1' - 0"

NORTH

HRP

HRP

HRP

HRP

HRP

HRP

HRP

HRP

11 11

11 11

HRP

10 10

M4.1

HRP

HRP

LUGGAGE

DOCK INTAKE/

RECYLABLES SORTING

LINEN

ELEVATOR

E2

STAIR

S5

LINEN

CART

STORAGE

AMENITY

STORAGE

ACCESSIBLE

BATH

104A

ACCESSIBLE

GUEST

ROOM

GUEST

ROOM

HALLWAY

BATH

106A

KING

GUEST

ROOM

BATH

108A

BATH

116A

BATH

118A

BATH

120A

HISTORIC

BATH

122A

HISTORIC

BATH

114A

GUEST

ROOM

KING

GUEST

ROOM

GUEST

ROOM

KING

GUEST

ROOM

GUEST

ROOM

122LINEN

STORAGE

ELEVATOR

LOBBY

STAIR

S4

VESTIBULE

ACCESSIBLE

GUEST

SUITE

GUEST

ROOM

GUEST

ROOM

GUEST

ROOM

GUEST

ROOM

GUEST

ROOM

GUEST

ROOM

GUEST

ROOM

KING

GUEST

ROOM

GUEST

ROOM

LOCATION

MANAGER

HOUSEKEEPING

OFFICE

OFFICE

ASSISTANT

TIMEKEEPING/

STAFF

LOCKERS

BATH

101A

BATH

103A

BATH

105A

BATH

107A

BATH

109A

ELECTRICAL

BATH

113A

BATH

117A

BATH

115A

MAINT.

HISTORIC

BATH

111A

SLEEPING

ROOM

119 B

ACCESSIBLE

BATH

119 A

VENDING

FT

7 7 7

SM-2

SM-1

1. MECHANICAL CONTRACTOR SHALL CUT ALL FLOORS,

WALLS, CEILINGS AND ROOF AS REQUIRED TO PERFORM

THE WORK DEPICTED IN THESE CONTRACT DOCUMENTS

AND SPECIFICATIONS. GENERAL CONTRACTOR SHALL

PATCH ALL ASSOCIATED FLOORS, WALLS, CEILINGS, AND

ROOF AS REQUIRED TO THE SATISFACTION OF THE

CONTRACTING OFFICER.

2. SEAL ALL MECHANICAL PENETRATIONS THROUGH FIRE

RATED ASSEMBLIES WITH UL-APPROVED FIRE RATED

SYSTEM.

3. HYDRONIC VALVES 2" AND SMALLER TO BE BALL VALVES.

HYDRONIC VALVES LARGER THAN 2" TO BE LUG STYLE

BUTTERFLY VALVES.

4. LOCATE ALL VALVES ABOVE ACCESSIBLE CEILINGS OR

PROVIDE ACCESS PANEL IN CEILING FOR VALVE ACCESS.

ACCESS PANELS SHALL BE RATED WHERE REQUIRED.

5. CONTRACTOR SHALL PROVIDE CONTRACTING OFFICER

WITH VALVE CHART OF ALL VALVES INSTALLED IN PROJECT

UPON COMPLETION.

6. COORDINATE HVAC AND PLUMBING ROUTING AND

EQUIPMENT WITH ALL OTHER TRADES AS REQUIRED.

7. VERIFY EXACT LOCATION OF THERMOSTATS WITH

CONTRACTING OFFICER PRIOR TO INSTALLATION.

9. COORDINATE ACCESS PANEL LOCATIONS WITH

CONTRACTING OFFICER BEFORE INSTALLATION.

RE

VI

SI

ON

M4.3

BASEMENT AND SECOND FLOOR

HYDRONIC PLAN - EXISTING

0 1 2 3 4 5 6 7 8 9 10 inches

DESIGNED

CADD

TECH. REVIEW

DATE

SUB SHEET NO. DRAWING NO.

PKG.

NO.

SHEET

OF

TITLE OF SHEET

C O

N S

T R

U C

T

IO

N D

O C

U M

E N

T S

YELL 101

135239

30402.28.2018

PKG 1

101 E. BROADWAY

BELGRADE, MT 59714

PH: (406) 388-3320

FAX: (406) 388-3389

ACE PROJECT #: 13BZ4199.005

PROJECT NO:

REVISIONS:

PMIS NO. 205796

15021.40

MAMMOTH HOTEL PHASE II

GUEST WING RENOVATION

NATIONAL PARK SERVICE - US DEPARTMENT OF THE INTERIOR

MAMMOTH HOT SPRINGS, WY - YELLOWSTONE NATIONAL PARK

04.09.20181

11 SECOND FLOOR HYDRONIC PLAN - EXISTING BUILDING

M4.3 : M4.3 1/8" = 1' - 0"

NORTH

U P

D N

KEY HYDRONIC DEMOLITION NOTES:

CAREFULLY REMOVE FINISH ON INTERIOR SIDE OF PANTRY WALL AND ROUTE PIPING FROM CU-3

UP IN WALL CAVITY TO CEILING SPACE. CONTINUE PIPING INTO ATTIC SPACE AS SHOWN AND

CONNECT TO EXISTING REFRIGERANT PIPING AT LOCATION SHOWN. FIELD VERIFY EXACT

LOCATION OF EXISTING REFRIGERATION PIPING. PATCH AND REPAIR WALLS AND CEILING AS

REQUIRED.

EXISTING REFRIGERANT PIPING TO REMAIN AS-IS.

EXISTING FAN COIL TO REMAIN AS-IS.

PROVIDE EXISTING CONDENSING UNIT WITH SPRING VIBRATION ISOLATOR RACK. FIELD

FABRICATE RACK FOR AAON UNIT WITH SPRING ISOLATOR IN EACH CORNER. FIELD FABRICATE

ONE RACK FOR BOTH DAIKIN UNITS WITH SIX SPRING ISOLATORS. ENSURE ALL REFRIGERANT

PIPING AND POWER CONNECTIONS REMAIN CONNECTED.

INSTALL CU-3 AT APPROXIMATE LOCATION WITH VIBRATION SPRING ISOLATORS. FIELD FABRICATE

RACK WITH SPRING ISOLATORS ON EACH CORNER. ROUTE PIPING ALONG WALL AS SHOWN TO

MAINTAIN ACCESS THROUGH WINDOW FROM PANTRY.

CONNECT NEW REFRIGERANT PIPING TO EXISTING PIPING AS REQUIRED. FIELD VERIFY EXACT

LOCATION OF EXISTING PIPING. INSULATE ALL NEW REFRIGERANT PIPING.

EX

CU

EX

CU

EX

CU

TO EXISTING FC-6

IN ATTIC

EX

FC-2

EX

FC-1

EX

FC-4

EX

FC-3

EX

FC-5

GENERAL HYDRONIC NOTES:

1. MECHANICAL CONTRACTOR SHALL CUT ALL FLOORS, WALLS, CEILINGS AND ROOF AS REQUIRED TO PERFORM THE WORK DEPICTED IN THESE CONTRACT DOCUMENTS AND SPECIFICATIONS. GENERAL CONTRACTOR SHALL PATCH ALL ASSOCIATED FLOORS, WALLS, CEILINGS, AND ROOF AS

REQUIRED TO THE SATISFACTION OF THE CONTRACTING OFFICER.

2. SEAL ALL MECHANICAL PENETRATIONS THROUGH FIRE RATED ASSEMBLIES WITH UL-APPROVED FIRE RATED SYSTEM.

3. HYDRONIC VALVES 2" AND SMALLER TO BE BALL VALVES. HYDRONIC VALVES LARGER THAN 2" TO BE LUG STYLE BUTTERFLY VALVES.

4. LOCATE ALL VALVES ABOVE ACCESSIBLE CEILINGS OR PROVIDE ACCESS PANEL IN CEILING FOR VALVE ACCESS. ACCESS PANELS SHALL BE RATED

WHERE REQUIRED.

5. CONTRACTOR SHALL PROVIDE CONTRACTING OFFICER WITH VALVE CHART OF ALL VALVES INSTALLED IN PROJECT UPON COMPLETION.

6. COORDINATE HVAC AND PLUMBING ROUTING AND EQUIPMENT WITH ALL OTHER TRADES AS REQUIRED.

CONFERENCE ROOM

CONFERENCE ROOM

PANTRY

HALLWAY

STOR

STAIR

S1

BOARD ROOM

CU

TO EXISTING FC-10

IN ELECTRICAL

ROOM

9 CRAWLSPACE MECHANICAL PLAN - EXISTING BUILDING

MD4.3 : MD4.3 1/8" = 1' - 0"

NORTH

U P

D A

C B

KEY HYDRONIC DEMOLITION NOTES:

EXISTING FAN COIL FC-10 TO REMAIN AS-IS. CONNECT

COMMUNICATIONS LINE TO NEW CU-3 LOCATED ON

ROOF BY PANTRY.

EXISTING REFRIGERANT PIPING TO REMAIN AS-IS. SEE

SHEET M4.3 FOR NEW REFRIGERANT PIPING

CONNECTIONS AND ROUTING.

EXISTING THERMOSTAT TO REMAIN AS-IS CONNECTED

TO FC-10.

ROUTE 22"X16" OUTSIDE AIR DUCT UP IN CHASE TO

LOUVER L-6. INSULATE ENTIRE DUCT.

INSTALL L-6 LOUVER ON EXTERIOR WALL UNDER

EXISTING LOUVER. MOVE EXISTING LOUVER UP TO FIT

NEW LOUVER BELOW AND EXTEND EXISTING DUCT AS

REQUIRED. PATCH AND REPAIR WALL AS REQUIRED.

SUSPEND EXHAUST FAN FROM CEILING AT

APPROXIMATE LOCATION. UNIT SHALL BE CONTROLLED

BY REVERSE ACTING THERMOSTAT TIED TO THE LOW

LEAKAGE MOTORIZED DAMPER IN DUCT. CONNECT FAN

AND THERMOSTAT TO BUILDING AUTOMATION SYSTEM

AS REQUIRED.

FIELD FABRICATE FILTER RACK INSIDE DUCT AND

INSTALL MERV 8 FILTERS. PROVIDE ACCESS PANEL IN

CEILING TO ACCESS FILTER RACK.

MOUNT REVERSE ACTING THERMOSTAT ON WALL AT

APPROXIMATE LOCATION SHOWN. TIE THERMOSTAT

INTO EXHAUST FAN AND LOW LEAKAGE MOTORIZED

DAMPER IN EXHAUST DUCT AND INTEGRATE INTO

BUILDING AUTOMATION SYSTEM.

SUSPEND EXHAUST FAN FROM CEILING WITH VIBRATION

ISOLATORS. CONNECT DUCT TO FAN WITH FLEX

CONNECTORS. TERMINATE DUCT WITH OPEN END IN

MECHANICAL ROOM.

INSTALL LOW LEAKAGE MOTORIZED DAMPER IN DUCT AT

APPROXIMATE LOCATION SHOWN. CONNECT DAMPER

TO REVERSE ACTING THERMOSTAT AND EXHAUST FAN

TIED INTO BUILDING AUTOMATION SYSTEM.

INSTALL LOW LEAKAGE MOTORIZED DAMPER IN DUCT AT

APPROXIMATE LOCATION SHOWN. PROVIDE ACCESS TO

DAMPERS IN HARD LID CEILING IN CORRIDOR. CONNECT

MOTORIZED DAMPERS TO EXHAUST FANS. DAMPERS

SHALL OPEN WHEN EXHAUST FAN IS ENERGIZED.

INSTALL SG-1 AT APPROXIMATE LOCATION SHOWN.

RELOCATE EXISTING HWS AND FIRE SPRINKLER PIPING

AS REQUIRED TO FIT DUCTWORK AND GRILLE.

SAW CUT 20" X 20" HOLE THROUGH WALL AND ROUTE 20"

X 20" DUCT THROUGH WALL. TERMINATE DUCT WITH

OPEN END. FIELD VERIFY EXACT LOCATION OF SAW CUT.

ROUTE 20" X 20" DUCT THROUGH WALL AND TERMINATE

WITH OPEN ENDS.

CONDENSING UNIT SCHEDULE

PLAN

CODE

MANUF

MODEL

NUMBER

SERVES LOCATION

TOTAL CAP.

BTUH

SEN. CAP.

BTUH

AMB

TEMP

COMPRESSOR REFERENCE

PRODUCT

REMARKS

VOLTS PH FLA

CU-3 DAIKIN RXTQ48TAVJU FC-10 ROOF BY PANTRY 49.5 45.5 95 208 1 29.1 R-410A SEE NOTES BELOW

NOTES: PROVIDE WITH FACTORY DISCONNECT. INSTALL UNIT ON ROOF SUCH THAT ACCESS TO WINDOW AND OTHER UNITS REMAIN. PROVIDE WITH SPRING VIBRATION ISOLATORS.

MECHANICAL

ELECTRICAL / TEL DATA

HALLWAY

STAIR

S1

EX

FC-10

T

T

EF

EF

4 5

8 T

SG-1

EXHAUST FAN SCHEDULE

PLAN

CODE

MANUF

MODEL

NUMBER

CFM ESP RPM

ELECTRICAL

REMARKS

VOLT AMP PH

EF-4 ACME DM10 2200 0.5 913 120 13.8 1 BELT DRIVE

EF-5 ACME DM10 800 0.5 913 120 13.8 1 BELT DRIVE

NOTES: 1) PROVIDE REVERSE ACTING THERMOSTAT AND INTEGRATE INTO BUILDING AUTOMATION

SYSTEM. FANN SHALL OPERATE AND DAMPERS SHALL OPEN WHEN TEMPERATURE OF SPACE

EXCEEDS TEMPERATURE SETPOINT. PROVIDE FACTORY MOUNTED DISCONNECT.

GRILLE - LOUVER SCHEDULE

PLAN

CODE

MANUF

MODEL

NUMBER

MATERIAL FINISH CFM

VOLUME

DAMPER

REMARKS

SG-1 KRUEGER 580 ALUMINUM WHITE

SEE

PLAN

MOTORIZED

IN DUCT

30" X 12" GRILLE

SEE BELOW

SG-2 KRUEGER 580 ALUMINUM WHITE

SEE

PLAN

MOTORIZED

IN DUCT

14" X 10" GRILLE

SEE BELOW

L-3 RUSKIN ELF6375DX ALUMINUM

MATCH

EXTERIOR

3200 BACKDRAFT

22" x 48" LOUVER

SEE BELOW

NOTES: 1) PROVIDE ALL DUCT TRANSITIONS TO AND FROM GRILLES AND LOUVERS AS REQUIRED. PROVIDE

MOTORIZED DAMPERS IN DUCT BEFORE GRILLE. CONNECT MOTORIZED DAMPERS TO REVERSE ACTING

THERMOSTAT. PROVIDE ACCESS TO DAMPER IN CORRIDOR CEILING.

2) INSTALL L-3 BELOW EXISTING LOUVER AND PATCH AND REPAIR WALL AS REQUIRED.

SG-2

KEY PLAN KEY PLAN

RE

VI

SI

ON

P1.0

PLUMBING LEGENDS

0 1 2 3 4 5 6 7 8 9 10 inches

DESIGNED

CADD

TECH. REVIEW

DATE

SUB SHEET NO. DRAWING NO.

PKG.

NO.

SHEET

OF

TITLE OF SHEET

C O

N S

T R

U C

T

IO

N D

O C

U M

E N

T S

YELL 101

135239

30402.28.2018

PKG 1

101 E. BROADWAY

BELGRADE, MT 59714

PH: (406) 388-3320

FAX: (406) 388-3389

ACE PROJECT #: 13BZ4199.005

PROJECT NO:

REVISIONS:

PMIS NO. 205796

15021.40

MAMMOTH HOTEL PHASE II

GUEST WING RENOVATION

NATIONAL PARK SERVICE - US DEPARTMENT OF THE INTERIOR

MAMMOTH HOT SPRINGS, WY - YELLOWSTONE NATIONAL PARK

04.09.20181

AND SCHEDULES 226

DRAWING LIST

P1.0 PLUMBING LEGENDS AND SCHEDULES P2.3 THIRD FLOOR DOMESTIC WASTE AND VENT PLAN

PD2.0 CRAWLSPACE PLUMBING DEMOLITION PLAN P2.4 FOURTH FLOOR DOMESTIC WASTE AND VENT PLAN

PD2.1 FIRST FLOOR PLUMBING DEMOLITION PLAN P3.0 CRAWLSPACE DOMESTIC WATER PLAN

PD2.2 SECOND FLOOR PLUMBING DEMOLITION PLAN P3.1 FIRST FLOOR DOMESTIC WATER PLAN

PD2.3 THIRD FLOOR PLUMBING DEMOLITION PLAN P3.2 SECOND FLOOR DOMESTIC WATER PLAN

PD2.4 FOURTH FLOOR PLUMBING DEMOLITION PLAN P3.3 THIRD FLOOR DOMESTIC WATER PLAN

PD4.0 TUNNEL PLUMBING DEMOLITION PLAN P3.4 FOURTH FLOOR DOMESTIC WATER PLAN

P2.0 CRAWLSPACE DOMESTIC WASTE AND VENT PLAN P4.0 PLUMBING DETAILS

P2.1 FIRST FLOOR DOMESTIC WASTE AND VENT PLAN

P2.2 SECOND FLOOR DOMESTIC WASTE AND VENT PLAN

GLOBE VALVE

3-WAY (ELECTRIC)

THIS IS A STANDARDIZED SYMBOLS LEGEND, ALL SYMBOLS SHOWN MAY

or or or

NOT APPEAR ON OR WITHIN THIS SET OF CONTRACT DOCUMENTS.

VENT THRU ROOF

STRAINER W/ BLOW-OFF

3-WAY (PNEU. MTR.)

GAS COCK

3-WAY (PNEUMATIC)

PRESSURE GAUGE

TEMP. GAUGE

SENSOR (TEMP./FLOW)

FLEX. CONNECTION

SOLENOID GATE VALVE

HOSE BIBB

FLOAT VALVE

BALANCING VALVE

DRAIN

PLUG VALVE

CHECK VALVE

STRAINER

VTR

PIPING FITTINGS, VALVES & SPECIALTIES

P1P-1 or or or or or

PRESS. REDUCING

2-WAY (ELECTRIC)

2-WAY (PNEU. MTR.)

2-WAY (SOLENOID)

PNEUMATIC MOTOR

ANGLE VALVE

EXIST. FIXTURE TO REMAIN EXIST. FIXT. TO BE REMOVED NEW PLUMBING FIXTURE

FIXT. NUMBER - SEE SCHED.

GATE VALVE

BALL VALVE

CROSS IN HORIZ. RUN

90° AND 45° ELBOWS

END CAP CONNECTION

BELL AND SPIGOT

UNION FITTING

BRANCH TEE TURNED UP

BRANCH TEE TURNED DN.

DOMESTIC PIPING

DIRECTION OF FLOW

ELBOW TURNED DN.

TEE TURNED DN.

DROP IN HORIZ. RUN

TEE TURNED UP

ELBOW TURNED UP

REDUCER FITTING

or or

(TYPE)

TEE IN HORIZ. RUN

BRANCH TEE W/ OFFSETEXIST. TO BE REMOVED

GENERAL PIPING

EXISTING TO REMAIN or or

PUMPFIRE EXTINGUISHER

FIRE SPRINKLER HEAD

DISCONNECTION

P.O.D.C.-POINT OF

P.O.C.-POINT OF CONNECTION

MISCELLANEOUS/MECHANICAL PIPING

DOMESTIC COLD WATER

DOMESTIC HOT WATER

DOMESTIC HOT WATER RECIRC.

NATURAL GAS

BUTTERFLY VALVE

SANITARY WASTE - ABOVE FLOOR

SANITARY WASTE - BELOW FLOOR

VENT - ABOVE FLOOR

VENT - BELOW FLOOR

STEAM

or or

(TYPE)

G STM

HWRC

HW

CW

V

V

SAN

SAN

PLUMBING SYMBOLS LEGEND

ELEVATOR SUMP PUMP SCHEDULE

PLAN

CODE

MANUFACTURER MODEL NUMBER RPM GPM FT OF HD

ELECTRICAL

REMARKS

HP VOLT PH AMP

SP-1 LIBERTY MODEL 233-2 3450 30 10 1/3 115 1 5.2 INSTALL IN ELEVATOR PIT. SEE NOTES

PLUMBING FIXTURE SCHEDULE

PLAN CODE ITEM MANUFACTURER MODEL NUMBER MATERIAL & FINISH TRIM

ROUGH-IN SIZE

REMARKS

CW HW SAN VENT

BT-1 BATH TUB/SHOWER SIGN OF THE CRAB P0700C

ENAMELED WHITE CAST IRON, CHROME

TRIM

SIGN OF THE CRAB SP889C1* FAUCET, SIGN OF THE CRAB

P0342C SUPPLY, KOHLER K-45202 SHOWER, SIGN OF THE

CRAB P0007BEC DRAIN

2"

2" 2" 11

2" FAUCET TO BE P0889C BODY WITH SHOWER DIVERTER ASSEMBLY LESS HANDSHOWER. PROVIDE WITH ALL NECESSARY ACCESSORIES FOR A

COMPLETE INSTALLATION.

BT-2 ACCESSIBLE TUB/SHOWER KOHLER MEMOIRS K-722 CAST IRON W/ ENAMEL, CHROME TRIM

KOHLER K-496-V DIVERTER SPOUT, KOHLER K-TS16117-4A

HANDLE, KOHLER K-99899 HAND SHOWER, KOHLER K-304

VALVE

2"

2" 2" 11

2" 1.5 GPM ACCESSIBLE BATH/SHOWER WITH DIVERTER SPOUT.

BT-3 HISTORIC TUB/SHOWER OWNER PROVIDED ---- ----

SIGN OF THE CRAB SP889C1* FAUCET, SIGN OF THE CRAB

P0342C SUPPLY, KOHLER K-45202 SHOWER, SIGN OF THE

CRAB P0007BEC DRAIN

2"

2" 2" 11

2" FAUCET TO BE P0889C BODY WITH SHOWER DIVERTER ASSEMBLY LESS HAND SHOWER. REFINISH EXISTING ENAMEL FIXTURE AND INSTALL NEW

SHOWER TRIM. PROVIDE WITH ALL NECESSARY ACCESSORIES FOR A COMPLETE INSTALLATION.

BT-4 BATH TUB WITH TUB FILLER SIGN OF THE CRAB P0700C

ENAMELED WHITE CAST IRON, CHROME

TRIM

SIGN OF THE CRAB SP889C1* FAUCET, SIGN OF THE CRAB

P0342C SUPPLY, SIGN OF THE CRAB P0007BEC DRAIN

2"

2" 2" 11 2"

FAUCET TO BE P0889C BODY ONLY ASSEMBLY WITH PLUG FOR SHOWER. PROVIDE WITH ALL NECESSARY ACCESSORIES FOR A COMPLETE

INSTALLATION.

EW-1 EYE/FACE WASH BRADLEY S19294JBT STAINLESS STEEL CABINET S19-2000EFX MIX VALVE 1 2"

2" 2" 11

2" EMERGENCY FOLD DOWN EYE WASH. PROVIDE WITH MANUFACTURER RECOMMENDED THERMOSTATIC MIX VALVE AND INSTALL IN MAINTENANCE

CABINET OF EYE WASH UNIT.

FD-1 FLOOR DRAIN SCHLUTER KERDI-DRAIN KD2/ABS/6RE ABS BODY WITH STAINLESS STEEL GRATE 6RE 6" GRATE ---- ---- 2" 11

2" PROVIDE WITH TRAP GUARD.

FS-1 FLOOR SINK WADE W-9113-16 CAST IRON BODY A.R.E. INTERIOR ---------- ---- --- 3" 11

2" PROVIDE W/ 3 4 GRATE AND TRAP GUARD.

HB-1 HOSE BIBB WOODFORD MODEL 68 CHROME "T" HANDLE KEY 3

4" ---- ---- ---- BACKFLOW PROTECTED W/ VACUUM BREAKER

KS-1 1-COMP SINK 71

2" DEPTH KOHLER NORTHLAND K-6589-U ENAMELED CAST IRON, CHROME TRIM SIGN OF THE CRAB SP549-12C1* 1

2"

2" 2" 11 2"

WALL MOUNTED FAUCET WITH LEVER HANDLES. INSULATE HW, CW, SAN, & STOPS AS REQ'D. OFFSET P-TRAP. MOUNT TO CONFORM TO ALL A.N.S.I. &

A.B.A. REQUIREMENTS. GRID STRAINER AND STOPPER TYPE DRAIN.

LAV-1 COUNTERTOP LAVATORY KOHLER KELSTON K-2382 VITREOUS CHINA WHITE, CHROME TRIM SIGN OF THE CRAB SP549-12C1* 1 2"

2" 2" 11

2" WALL MOUNTED FAUCET WITH LEVER HANDLES. INSULATE HW, CW, SAN, & STOPS AS REQ'D. PROVIDE WITH LIFT AND TURN DRAIN.

LAV-2

ACCESSIBLE COUNTERTOP

LAVATORY

KOHLER KELSTON K-2382 VITREOUS CHINA WHITE, CHROME TRIM SIGN OF THE CRAB SP549-12C1* 1

2"

2" 2" 11 2"

WALL MOUNTED FAUCET WITH LEVER HANDLES. INSULATE HW, CW, SAN, & STOPS AS REQ'D. OFFSET P-TRAP. MOUNT TO CONFORM TO ALL A.N.S.I. &

A.B.A. REQUIREMENTS. PROVIDE WITH LIFT AND TURN DRAIN.

LAV-3 HISTORIC LAVATORY OWNER PROVIDED --- --- SIGN OF THE CRAB P0549-12C FAUCET 1 2"

2" 2" 11

2" DECK MOUNTED FAUCET WITH CROSS HANDLES. INSTALL NEW TRIM. VERIFY EXISTING HOLE PUNCHING CENTERS OF ALL FIXTURES BEFORE

ORDERING FAUCET. PROVIDE WITH LIFT AND TURN DRAIN.

LAV-4 PEDESTAL LAVATORY KOHLER MEMOIRS K-2238-8 VITREOUS CHINA WHITE, CHROME TRIM SIGN OF THE CRAB P0565-8C 1 2"

2" 2" 11

2" DECK MOUNTED FAUCET WITH LEVER HANDLES. INSULATE HW, CW, SAN, & STOPS AS REQ'D. OFFSET P-TRAP. MOUNT TO CONFORM TO ALL A.N.S.I. &

A.B.A. REQUIREMENTS. PROVIDE WITH LIFT AND TURN DRAIN AND CHROME CENTER HOLE COVER.

MS-1 MOP SINK FIAT MSB-2424 MOLDED STONE KOHLER K-8928 FAUCET 3

4"

4" 3" 11

2" PROVIDE WITH VACUUM BREAKER, INTEGRAL CHECK STOPS, HOSE & BRACKET, FIAT MOP HANGER #889-CC, & VINYL BUMPER GUARD #E-77-AA.

SB-1 ICE MACHINE SUPPLY BOX OATEY 39121 THERMOSET FIRE-RATED PLASTIC, WHITE --- 1 2" --- --- --- FIRE-RATED, QUARTER TURN VALVE. PROVIDE ICE MAKER WITH BACKFLOW PREVENTION.

SH-1 SHOWER VALVE AND TRIM KOHLER K-304-KS BRASS VALVE, CHROME TRIM

KOHLER K-TS16117-4A HANDLE, K-45202 SHOWERHEAD,

KERDI-LINE KLB LINEAR DRIAIN

2"

2" 2" 11

2" 1.5 GPM SHOWER. CONTRACTOR TO VERIFY LINEAR TRENCH DRAIN LENGTH.

SH-2

ACCESSIBLE SHOWER VALVE AND

TRIM

KOHLER K-304-KS BRASS VALVE, CHROME TRIM

KOHLER K-TS16117-4A HANDLE, KOHLER K-99899 HAND

SHOWER, KERDI-LINE KLB LINEAR DRIAIN

2"

2" 2" 11 2"

1.5 GPM ACCESSIBLE SHOWER. MOUNT TO CONFORM TO ALL A.N.S.I. & A.B.A. REQUIREMENTS. CONTRACTOR TO VERIFY LINEAR TRENCH DRAIN

LENGTH.

TD-1 LINEAR SLOT DRAIN SCHLUTER KERDI-LINE STAINLESS STEEL BODY KLB PERFORATED GRATE ---- ---- 2" 11 2" PROVIDE WITH TRAP SEAL. CONTRACTOR TO VERIFY EXACT CHANNEL LENGTH PER ARCHITECT DRAWINGS.

WC-1 F.T. H.C. F.M. WATER CLOSET KOHLER MEMOIRS K-3812 VITREOUS CHINA WHITE,…