Replacement of Tile on Cafeteria
The purpose of this amendment is to correct the due date.The USDA - Forest Service WO-AQM Job Corps Support Branch has identified the need of a service contractor to replace tile in the cafeteria at the Weber Basin Job Corps Center, located in Ogden, Utah.
This requirement will be issued as a Request for Quote (RFQ), under FAR Part 13. The RFQ will result in a single firm fixed-price award from the lowest responsive and responsible bidder.
This requirement will be set aside for Total Small Business.
The North American Industry Classification System (NAICS) is 238340. The size standard is $15M.
This requirement is set aside to Small Businesses as authorized by FAR 19.502-2 (b). In accordance with FSAR 4G13.106-2 additional preference may be given to potential vendors or suppliers if they are 8(a) or other small disadvantaged businesses, even if the resulting pricing may be higher than the lowest quote received.
All vendors are encouraged to inspect the site where services are to be performed and to satisfy themselves regarding all general and local conditions that may affect the cost of contract performance, to the extent that the information is reasonably obtainable. In no event shall failure to inspect the site constitute grounds for a claim after contract award.The specifications WILL NOT be provided in a paper hard copy format or CD ROM, and will only be posted on the Federal Business Opportunities (FBO) website. The address for downloading this solicitation from the Internet is https://www.fbo.gov. Registration and downloading from the Internet is free of charge; however, some specifications may take a considerable amount of time to download. All prospective offerors are required to register on the Federal Business Opportunities (FEDBIZOPPS) website for this procurement. An official plan holders list will be maintained on and can be printed from the website. If you fail to register, the Government cannot be responsible for your being notified of any amendments to the solicitation. Notification of any changes to this solicitation (amendments) shall be made only on the internet through FBO. Therefore, it is the contractor's responsibility to check the Internet site daily for any posted changes to the solicitation. In addition, all contractors doing business with the Federal Government must be registered in the U.S. Contractor Registration System SAMS at https://www.sam.gov. NOTE: Offerors should submit verification of their firm's registration in the SAMS database with their offer.QUOTE SUBMISSION
In lieu of sending written inquiries via the postal service, all potential quoters must submit all inquiries and quotes electronically via email to the email address stated below.
Any mailed (postal service), shipped (UPS/FEDEX, etc.) or hand delivered quotes will not be accepted or considered for award.
All bids must be received no late than 1400 Mountain Time on March 30, 2018 to Jennifer McCord at: jennifermccord@fs.fed.us BASIS OF AWARD AND EVALUATION OF QUOTES
Bidders shall enter a price for all items listed in PRICING SCHEDULE. There will be one award from this solicitation.
The Government will issue a contract as a result of this RFQ to the contractor who has been determined to be both responsive and responsible, and offers the Lowest Price overall.
It is the Government's intent to determine reasonableness and the bidder's understanding of ALL the work required and the ability to perform ALL of the work stated under the contract. Any exclusions listed in reference to prescribed work, may remove the contractor from consideration.
The Government may reject any or all quotes, issue orders to other than the lowest quote, and waive minor informalities or irregularities in quotes received, or elect to not award at all. If necessary, the Government may conduct discussions with any or all quoters.
The Government may issue an order on the basis of quotes as received, without entering into discussions with any quoter. Therefore, each initial quote should contain the quoter's best terms and must speak directly to the evaluation factors listed.
Note: Those not submitting past performance and biobased information as outlined will be considered not responsive and therefore not be considered for award
1282A718Q0030 Department of Agriculture Forest Service
3/23/18, 2:56 PM Presolicitation Notice Table Rock Lake Floor Tile Installation W9127S-09-B-0017
Added: Apr 08, 2009 12:42 pm
The Little Rock District Corps of Engineers has a requirement to install tile at the Table Rock Lake Project Office. The work will take place at Table Rock Lake 4600 State Highway 165 Branson, MO 65616. The contractor shall furnish all labor, materials, tools, equipment and supervision. The work includes but is not limited to the removal and re-installation of office furniture and miscellaneous items as needed to complete the work as specified. NAICS code 238340 /$14.0This acquisition will be released as a 100% small business set-aside. The Invitation for Bid (IFB) is anticipated to be posted on or about 24 April 2009. Bids are due 25 May 2009, 2:00 pm (CST). The solicitation documents for this project will be available via the Federal Business Opportunities (FBO) website at https://www.fbo.gov/ under solicitation number W9127S-09-B-0017.You must be registered with the FBO website to download the solicitation documents. NO CD's OR HARD COPIES WILL BE MADE AVAILABLE. It is therefore the contractors responsibility to check the ASFI website daily for any posted changes. Bidders are responsible for checking the referenced page for any update(s) to this notice. The Government is not responsible for any loss of Internet connectivity or for an offeror's inability to access the documents posted at the referenced website. To obtain automatic notifications of updates to this solicitation, you MUST log in to www.fbo.gov and add the solicitation to your 'Watchlist.' If you would like to list your firm so others can see you are an interested vendor, you must click the 'Add Me to Interested Vendors' button in the listing for this solicitation on www.fbo.gov. For additional Little Rock District Contracting opportunities, see the FBO website at www.fbo.gov. Bidders must be registered with the Central Contractor Registration (CCR), in order to receive a Government contract award. To register, the CCR Internet address is: http://www.ccr.gov. The contracting officer for this solicitation will be Gerald Sanderson. All questions or comments should be forwarded to the Contract Specialist, Carmen Terrell, in writing by fax at (501)324-5196 or by e-mail to carmen.n.terrell@usace.army.mil.
W9127S09B0017 Department of the Army Corps of Engineers Engineering District Little Rock
4/8/09, 12:42 PM Sani Glaze Application to Bathroom Floors
Added: Sep 01, 2011 9:56 am
Statement of WorkUSCG Support Center - Elizabeth City, NCBldg 4 Bathroom/Head Project1. SCOPE: The contractor is to provide supervision, equipment all materials and labor to restore approximately 15 bathroom floors and 2 shower floors tile areas to a "like new" appearance and integrity with additional floor treatment to produce a moisture barrier and condition the floor so that this appearance can be maintained using conventional cleaning processes in combination with periodic prescribed support service activities.square foot for the floors and cove base in each building.1. Building 4 2. Men's Staff Restroom 135 3. Women's Staff Restroom 135 4. Women's Restroom 135 5. Men's Restroom 135 6. Women's RR 119 170 7. Men's Restroom 120 200 8. Wet Lab Room 123 320 9. Men's Restroom 122 200 10. Women's Restroom 121 17011. Building 812. Women's Restroom 36 13. Men's Restroom 169 14. ATTC Staff Women's RR 145 15. ATTC Staff Shower 25 16. ATTC Staff Men's RR 182 17. ATTC Staff Shower 2518. Hanger Building 619. Men's Restroom Floor 80 20. Women's Restroom Floor 80Total= 2,342 square feet 21. GOVERNMENT FACILITIES AND UTILITIES: Electrical power and water are available on the site. Telephone services will not be available for contractor use by the contractor. Bath rooms will be provided by Government.22. MATERIALS AND LOCATIONS:a. Contractor shall provide materials. Contractor shall ensure that all packages and containers are clearly marked with manufacturer's name, name brand and description of contents. Storage shall be IAW manufacturer's recommendations.b. Contractor is required to comply with all VOC laws and regulations. All subject Material Safety Data Sheets shall be available upon request. 23. SCHEDULE OF WORK: Completion of work should be accomplished within 21 calendar Days from receipt of notice to proceed. Normal work hours are 0800 to 1630. Alternate work hours must be approved by the Contracting Officer's Technical Representative (COTR).24. EXISTING CONDITIONS: The Contractor is expected to satisfy himself as to the existing conditions and all work to be performed. The contractor shall verify all dimensions prior to bidding, ordering materials or commencement of work. A site visit is highly encouraged and can be arranged with the COTR, David Meads, at (252) 335-6854.25. LIABILITY OF CONTRACTOR: Any damage to Government property caused by the contractor, shall be repaired or replaced by the contractor at no cost to the government. The contractor shall not disconnect any service without prior approval from the COTR.26. INSPECTION AND ACCEPTANCE: The COTR will accomplish inspection and acceptance of work.27. LABOR LAWS: The Davis-Bacon Act applies to the procurement.28. Safety: The contractor is wholly responsible for work site safety. The contractor shall implement a safety program that protects the lives and health of personnel in the construction area, prevents damage to property and avoid work interruptions. To accomplish this end, the Contractor shall provide appropriate safety barricades, signs, signal lights, etc. as well as comply with the requirements of all Federal, State and Local safety laws, rules and regulations.29. SITE RESTORATION & CLEAN UP: Upon completion of the job, the Contractor shall clean up the job site, returning it to the state of cleanliness equal or exceeding that in which it was found. The Contractor shall properly dispose of any trash, extra materials, dirt, debris or other litter that remains. There will be no final acceptance of the contract until the appearance of the job site is approved by the COTR.30. SUBMITTALS: Product Data including technical bulletins and MSDS shall be submitted with quotation for the following: (Spray Foam Insulation materials submittal)31. TECHNICAL REQUIREMENTS: TECHNOLOGYSaniGLAZE International LLC. is the developer of a new industry standard for ceramic tile andgrout restoration and maintenance, known generically as restorative bonding. This technology ispermanent in nature, and should not be confused with our compared to grout painting, staining,or otherwise re-coloring.SaniGLAZE International, LLC. represents that the SaniGLAZE tile and grout restorationprocess is:1) An new and emerging technology2) Environmentally friendlyWORK REQUIREMENTS1. Site PreparationA. Remove all existing surface polymer based coatings and/or seals with eitherSaniGLAZE Polymer Remover, Build Up Remover, Seal Remover, or equivalentand agitate the floor to ensure loosening and emulsification of such matter. Allemulsified detritus to be removed by suction. A free rinsing neutralizer shall beapplied to ensure that all surface contaminants have been removed and the floorsurface is tested using the hydrion method at a pH level which will not neutralizechemicals used in the sealing and finishing process. The residue of the solutionshall be removed by suction. 2. Moisture Sealing and FinishingA. The floor shall be mechanically scrubbed utilizing SaniGLAZE Extra StrengthContaminant Remover or equivalent to remove any remaining embeddedcontaminants from tile and grout surfaces. The scrubbing residue shall beremoved by suction and a clean water flood rinse applied. The rinse solutionshall be removed by suction and pH level buffered and tested with the hydrionmethod so as not to neutralize chemicals used in the grout prep process.B. Grout Preparation ProcedureA grout preparation gel shall be applied to the entire surface of the floor.1. Grout lines will be chemically etched and cleaned using SaniGLAZETile & Grollt Prep or equivalent that is specifically targeted to leave agrout surface conducive to micro anchor bonding with SaniGLAZE HighBuild Glazing Compound or equivalent.a. The grout preparation gel shall be a maximum strength, nonfuming product comprised of organic and inorganic chelating, scale removing compounds, suspending agents, penetrating detergents, water soluble solvent compounds, viscosity control agents, and odor suppressants.b. It shall remove embedded soils, dissolve micro-scale andmineral deposits, neutralize iron, rust, and mineral and urine stains without attacking the substrate or excessively dissolving cementitious grout or mortar joints, or having a deleterious effect on metal, fiberglass, porcelain, or ceramic fixtures.c. The grout preparation gel shall promote maximum contacting time and applicator control of the process, and reduce contact hazards to a minimum.d. The grout preparation gel shall leave no residue, chalk, or grit when properly rinsed.e. The grout preparation gel shall possess a minimum shelf life of one year.2. A clear water flood rinse shall be applied to the floor and the residueremoved by suction.C. SaniGLAZE Surface Rejllvenator or equivalent shall be applied to the entire floorafter the grout preparation gel has been removed. It shall neutralize all traces of previously applied chemicals. The rinsate shall be removed by suction and the floor is to be completely dried by means of a mechanically generated air flow.D. Any missing grout shall be replaced with SaniGLAZE High Build DIy Solids Grout Replacement System or equivalent. This material shall be non porous and have bonding properties equal to or better than original grout. It shall be of proper viscosity as to seek and fill all substrate voids by gravity and level to the original grout surface level.E. Grout GlazingA waterborne moisture impermeable grout glazing compound shall be applied to the existing grout between the tiles and leveled to the surface depth of the pretreated grout. This compound shall be available in varying colors and be capable of matching the existing grout and must not remain on any tile surface. This compound must bond with the grout and be cured to form an impermeablebarrier to moisture. This compound shall be SaniGLAZE High Build Glazing Compound or equivalent, in combination with SaniGLAZE Dry Solids to preventshrinkage and pitting during the curing process.1. SaniGLAZE High Build Glazing Compound and Dry Solids orequivalent shall be used for restoring grout lines greater than 62.5 milsdeep. It shall be formulated to function synergistically with otherSaniGLAZE or equivalent products. It shall be of sufficient nonvolatilevolume as to actually rebuild rather than simply stain grout. It shall alsobe of sufficient internal chemical crosslinking to create a cohesive, wearresistant surface and shall have a warranty of a minimum of two years.2. SaniGLAZE Glazing Compound or equivalent shall be used forrestoring grout lines less than 62.5 mils deep. It shall be identical to HighBuild Glazing Compound except for a lower nonvolatile volume whichmakes it suitable for shallow grout lines.F. SealingPorous TileA waterborne tile surface moisture and grease barrier, SaniGLAZE Matte Finish or equivalent, shall be applied to the entire tile surface to provide impermeable moisture seal over the entire treated area. This shield shall have an invisible appearance when it is dried. This product shall be an oil and water repellent compound with sufficient particle size of the emulsion and surfactant package toallow deep penetration of porous tile substrates, and must have an adhesion mechanism which is both mechanical and chemical. This compound must be able to recoat itselfwhen maintenance needs arise. The compound must be slip resistant and produce a Static Coefficient of Friction or at least .81 dry and .67 wet when tested with the ASTM Test Method C1028-96.Non Porous TileA waterborne tile surface moisture and grease, and chemical barrier, SaniGLAZE Super Shield or equivalent, shall be applied to the entire tile surface to provide impenneable moisture seal over the entire treated area. This shield shall have a low luster appearance when it is dried. This product shall be an oil and water repellent, as well as resistant to urine, disinfectants, bleach, acid bowl cleaner, high pH cleaners, and other chemicals typically used in cleaning rest rooms and other tile and grout areas, and must have a chemical adhesion mechanism. This compound must be able to recoat itself when maintenance needs arise. The compound must be slip resistant and produce a Static Coefficient of Friction or at least .75 dry and .57 wet when tested with the ASTM Test Method CI028-96.G. DowntimeThe floor must be available for foot traffic in four hours after completion of the work. 3. Support ServiceA. Contractor shall offer an optional periodic sanitation support service. This serviceshall be capable of removing any surface soil and contaminants and bring the floor back to the same" like new" appearance as affected by the restoration, using SaniGLAZE Surface Rejuvenator or equivalent and renew the original SaniGLAZE Matte ofSuper Shield which was applied during the original SaniGLAZE restoration.4. WarrantyA. Provide a one year warranty on the integrity of the completed process when maintained in accordance with specified procedures. Acts of God, neglect, and abuse are excluded.B. Contractor shall warrant the appearance and integrity of the tile and grout surface indefinitely as long as an optional sanitation support service iscontinued by the owner.5. History & PerformanceContractor must have verifiable experience in performing and managing large scale restroom tile restoration and maintenance activities. Additionally, contractor must have references in place to support this experience and certify satisfactory performance.
CGATTC2 Department of Homeland Security US Coast Guard
9/1/11, 9:56 AM