SOK-D-NXRAD-E023.pdf

04’ 4’ 8’

SCALE: 1/4" = 1’-0"

4’-0"

5’-8�"

4’

CHARGER

BATT

120/208V, 3PH, 4W

125KW EG

ATS

MSD

STORAGE SHELTER

UPS BLDG

MDPE

RMM

SEE NOTE 3

TVSS

TANK

DAY

PANEL

CTRL

ENV

SEE NOTE 19

SEE NOTE 16

SEE NOTE 2

SEE NOTE 15

PANEL

HOUSE

EG TVSS

SEE NOTE 17

EG ROOM DS

DISC

TVSS

SEE NOTE 14

"8 74’-3 "8

713’-8

8’-10�"

"8 715’-11

’-6

E D

M

IS

S

U E

D F

O R

HI

WY

JKB

ES 08/29/2018 1704153

SOK-D-NXRAD-E023

C O

N S

T R

U C

T

IO

N

ENGINEERING SERVICES

INFRASTRUCTURE

NEXRAD

UNDERGROUND CONDUIT

ELECTRICAL SITE PLAN AND

KAUAIIOLEAU

PROJECT ENGINEER MGR: ENGINEERING - LA

s o k -d -n x ra d -e

.d g n

DRAWING PRODUCED ON WSA MICROSTATION SYSTEM

ATO - TECHNICAL OPERATIONS WESTERN SERVICE AREA

NOTES FOR UNDERGROUND CONDUIT LAYOUT

19.

18.

17.

16.

15.

14.

13.

12.

11.

10.

9.

8.

7.

6.

5.

4.

3.

2.

1.

INSTALL

INSTALL

INSTALL

INSTALL

INSTALL

INSTALL

INSTALL

INSTALL

INSTALL

INSTALL

N

N

N

MDPE TO EG PANEL

TO USE FROM

EXISTING SPARE

ATS TO MDPE

CONDUIT FROM

UNDERGROUND

EXISTING 3"

RMM TO PB#2

CONDUIT FROM

UNDERGROUND

EXISTING 3"

POWER

2-3" PVC

EXISTING

COMM

2-2" PVC

EXISTING

REPLACEMENT SHELTER FOR EG

PB #1

EXISTING

PULLBOX #3

NEW 4’X4’

INSTALL

(FUTURE)

4, 12 & 13

SEE NOTE

1, 12 & 13

SEE NOTE

PB

#24’

X4

’NEWIN

STALL

POWER CONDUCTORS. Ref. FAA-C-1391e, Section 5.5.10e.

OUTSIDE WALL TO OUTSIDE WALL FROM CONDUIT WHICH CONTAIN

SYSTEM. CONDUIT FOR CONTROL CABLES NEED A MINIMUM OF 3"

2" PVC COATED RGS FROM PULLBOX #2 TO EG ROOM FOR RMM

FROM: ATS

TO: MDPE

FROM: MDPE

TO: EG HOUSE PNL

FROM: MAIN SERV DISC SW

TO: EG ROOM DISC SW

CONDUIT.

BRASS TAGS THAT IDENTIFY CABLES BEING INSTALLED FOR EACH

CONDUIT/COUPLING FLUSH WITH THE FINISHED FLOOR.

SWITCH TO LOADBANK CONTROLS UNIT. STUB UP THE

3" PVC COATED RGS FROM 125KW EG LOADBANK DISCONNECT

DISCONNECT SWITCH.

3" PVC COATED RGS FROM NEW PULLBOX #3 TO EG ROOM

2" PVC COATED RGS FROM PULLBOX #2 TO EG HOUSE PANEL.

CONDUIT ENTRY AREA.

3" PVC COATED RGS FROM ATS TO EG. REF DRAWING E021 FOR

ASSEMBLY ON THE INTERIOR OF THE CONCRETE PULLBOX.

A 26"X4"X1/4" COPPER GROUND PLATE WITH COVER AND MOUNTING

THE CONTRACTOR TO GROUND THE INTERIOR CONDUITS.

THE INTERIOR OF THE PULLBOX. THIS GROUND PLATE WILL ALLOW

FROM THE EES TO THE GROUND PLATE WHICH WILL BE INSTALLED ON

A 2" PVC SCH SLEEVE FOR A BARE #4/0 COPPER CONDUCTOR

LINE".

DETECTABLE UNDERGROUND TAPE. "CAUTION: BURIED ELECTRICAL

GRADE SHALL BE 3" PER 100 FEET.

ALL CONDUIT SHALL BE LAID TO SLOPE TOWARDS THE MANHOLE.

MINIMUM CONDUIT DEPTH 24" BELOW GRADE.

MINIMUM OF 3" (OUTSIDE WALL TO OUTSIDE WALL).

MINIMUM SEPARATION BETWEEN CONTROL AND POWER SHALL BE A

DIRECTION.

6" APART (OUTSIDE WALL TO OUTSIDE WALL) IN A VERTICAL

TO OUTSIDE WALL) IN A HORIZONTAL DIRECTION OR NOT LESS THAN

THEY SHALL BE SPACED NOT LESS THAN 2" APART. (OUTSIDE WALL

WHEN TWO OR MORE DUCTS ARE INSTALLED IN THE SAME TRENCH,

2234 TAPE PRIOR TO BURIAL.

THE DAMAGED AREAS OF THE 40 MIL PVC COATING WITH SCOTCH

AFTER THE CONDUIT AND COUPLING HAVE BEEN INSTALLED REPAIR

COATED HOT DIPPED RIGID GALVANIZED STEEL CONDUIT.

ALL UNDERGROUND CONDUIT AND FITTINGS SHALL BE 40 MIL PVC

RATED. MINIMUM LID OPENING TO BE 36"X 36".

NEW 4’X4’ PULLBOX WITH GALVANIZED STEEL LID H-20 TRAFFIC

PULLBOX #2.

(2) - 3" PVC COATED RGS CONDUIT FROM ATS TO EXISTING

DISCONNECT TO NEW PULLBOX #3.

(2) - 3" PVC COATED RGS CONDUIT FROM MAIN SERVICE

RATED. MINIMUM LID OPENING TO BE 36"X 36".

NEW 4’X4’ PULLBOX WITH A GALVANIZED STEEL LID H-20 TRAFFIC INSTALL

INSTALL

INSTALL

INSTALL

INSTALL

INSTALL

INSTALL

INSTALL

s o k -d -n x ra d -e

.d g n

/6 /2

:3

:2

A

M Is a b e ll e C

T R I n a

A

B

C

D

E

F

G

H

8 7 6 5 4 3 2 1

H

G

F

E

D

C

12345678

REVDRAWING NO

DATE JCN

APPROVED BY

ISSUED BY

CHECKED

DRAWN

DESIGNED

SUBMITTED BY

REVIEWED BY

FEDERAL AVIATION ADMINISTRATION

DEPARTMENT OF TRANSPORTATION

REV

DATE

APPROVED

DESCRIPTION JCN

DATE

REDLINE

APVD

A