Draft_RFP.pdf

DRAFT

(See ).

SOLICITATION, OFFER,

AND AWARD

(Construction, Alteration, or Repair) IMPORTANT - The "offer" section on the reverse must be fully completed by offeror.

9. FOR INFORMATION

CALL:

NOTE: In sealed bid solicitations "offer" and "offeror" mean "bid and "bidder".

SOLICITATION

1. SOLICITATION NO.

5. REQUISITION/PURCHASE REQUEST NO.

CODE

6. PROJECT NO.

8. ADDRESS OFFER TO

4. CONTRACT NO.

7. ISSUED BY

10. THE GOVERNMENT REQUIRES PERFORMANCE OF THE WORK DESCRIBED IN THESE DOCUMENTS (Title, identifying no., date)

11. The contractor shall begin performance

12a. THE CONTRACTOR MUST FURNISH ANY REQUIRED PERFORMANCE AND PAYMENT BONDS?

(If "YES", indicate within how many calendar days after award in Item 12b.)

13. ADDITIONAL SOLICITATION REQUIREMENTS:

a. Sealed offers in original and

b. An offer guarantee

c. All offers are subject to the (1) work requirements, and (2) other provisions and clauses incorporated in the solicitation in full text or by reference.

d. Offers providing less than

NSN 7540-01-155-3212

calendar days for Government acceptance after the date offers are due will not be considered and will be rejected.

is, is not required.

local time containing offers shall be marked to show the offeror's name and address, the solicitation number, and the date and time offers are due.

(date). If this is a sealed bid solicitation, offers will be publicly opened at that time. Sealed envelopes copies to perform the work required are due at the place specified in Item 8 by (hour) award, YES NO notice to proceed. This performance period is mandatory negotiable.

calendar days and complete it within calendar days after receiving

a. NAME b. TELEPHONE NO. (Include area code) (NO COLLECT CALLS)

12b. CALENDAR DAYS

2. TYPE OF SOLICITATION

SEALED BID (IFB)

NEGOTIATED (RFP)

3. DATE ISSUED PAGE OF PAGES

See Attached

STANDARD FORM 1442 (REV. )

Prescribed by GSA - FAR (48 CFR) 53.236-1(d)

*to be specified in each task order

As required by the task order

(As required by the task order)

17. The offeror agrees to perform the work required at the prices specified below in strict accordance with the terms of this solicitation, if this offer is accepted calendar days after the date offers are due. (Insert any number equal to or greater than the minimum requirement by the Government in writing within stated in Item 13d. Failure to insert any number means the offeror accepts the minimum in Item 13d.)

OFFER (Must be fully completed by offeror)

AMOUNTS

18. The offeror agrees to furnish any required performance and payment bonds.

19. ACKNOWLEDGMENT OF AMENDMENTS

(The offeror acknowledges receipt of amendments to the solicitation -- give number and date of each)

AMENDMENT NO.

DATE.

AWARD (To be completed by Government)

CONTRACTING OFFICER WILL COMPLETE ITEM 28 OR 29 AS APPLICABLE

14. NAME AND ADDRESS OF OFFEROR (Include ZIP Code)

CODE FACILITY CODE

15. TELEPHONE NO. (Include area code)

16. REMITTANCE ADDRESS (Include only if different than Item 14.)

20a. NAME AND TITLE OF PERSON AUTHORIZED TO SIGN OFFER (Type or print)

21. ITEMS ACCEPTED:

22. AMOUNT

26. ADMINISTERED BY

30a. NAME AND TITLE OF CONTRACTOR OR PERSON AUTHORIZED TO SIGN (Type or print)

31c. DATE31b. UNITED STATES OF AMERICA

BY

31a. NAME OF CONTRACTING OFFICER (Type or print)

29. AWARD (Contractor is not required to sign this document.) Your offer on this solicitation is hereby accepted as to the items listed. This award consummates the contract, which consists of (a) the Government solicitation and your offer, and (b) this contract award. No further contractual document is necessary.

30b. SIGNATURE 30c. DATE

28. NEGOTIATED AGREEMENT (Contractor is required to sign this document and return and deliver all items or perform all work requirements identified on this form and any continuation sheets for the consideration stated in this contract. The rights and obligations of the parties to this contract shall be governed by (a) this contract award, (b) the solicitation, and (c) the clauses, representations, certifications, and specifications incorporated by reference in or attached to this contract.

copies to issuing office.) Contractor agrees to furnish

24. SUBMIT INVOICES TO ADDRESS SHOWN IN

(4 copies unless otherwise specified)

23. ACCOUNTING AND APPROPRIATION DATA

ITEM 25. OTHER THAN FULL AND OPEN COMPETITION PURSUANT TO

27. PAYMENT WILL BE MADE BY

10 U.S.C. 2304(c) ( )

20b. SIGNATURE 20c. OFFER DATE

STANDARD FORM 1442 (REV. ) BACK

SCHEDULE Continued

ITEM NO. SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

In accordance with FAR 19.8, competition is limited to 8(a) firms located within Colorado, and other 8(a) firms with a bona fide place of business within the geographical competitive area.

The Government intends to award no more than 4 IDIQ contracts for construction from this solicitation.

The total maximum quantity to be ordered is $9,999,999 for the length of the contract, not to exceed five years.

The maximum quantity is calculated as the sum of all orders issued, including modifications, to all the Multiple Award Construction Contact (MACC) contractors.

The minimum guaranteed amount is $1,000 over the life of the contract.

0001 Contractor shall provide general construction services, per the attached statement of work.

1.00 EA

PAGE 3 OF 62 SB134118RP0009

Table of Contents

SECTION B SUPPLIES OR SERVICES AND PRICES/COSTS

B.1 1352.216-75 MINIMUM AND MAXIMUM CONTRACT AMOUNTS (APR 2010)

SECTION C DESCRIPTION/SPECIFICATIONS/WORK STATEMENT

C.1 Statement of Work

SECTION E INSPECTION AND ACCEPTANCE

E.1 52.246-12 INSPECTION OF CONSTRUCTION (AUG 1996)

SECTION F DELIVERIES OR PERFORMANCE

F.1 52.211-10 COMMENCEMENT, PROSECUTION, AND COMPLETION OF WORK (APR 1984)

F.2 52.242-14 SUSPENSION OF WORK (APR 1984)

SECTION G CONTRACT ADMINISTRATION DATA

G.1 52.232-5 PAYMENTS UNDER FIXED-PRICE CONSTRUCTION CONTRACTS (MAY 2014)

G.2 52.232-17 INTEREST (MAY 2014)

G.3 52.232-23 ASSIGNMENT OF CLAIMS (MAY 2014)

G.4 52.232-33 PAYMENT BY ELECTRONIC FUNDS TRANSFER--SYSTEM FOR AWARD MANAGEMENT (JUL 2013)

G.5 1352.201-70 CONTRACTING OFFICER?s AUTHORITY (APR 2010)

G.6 1352.201-72 CONTRACTING OFFICER`S REPRESENTATIVE (COR) (APR 2010)

G.7 1352.216-76 PLACEMENT OF ORDERS (APR 2010)

G.8 NIST LOCAL-40BILLING INSTRUCTIONS FOR DELIVERY/TASK ORDERS

G.9 NIST LOCAL-53CONTRACT PERFORMANCE DURING CHANGES IN NIST OPERATING STATUS

SECTION H SPECIAL CONTRACT REQUIREMENTS

H.1 1352.228-70 INSURANCE COVERAGE (APR 2010)

H.2 1352.237-71 SECURITY PROCESSING REQUIREMENTS - LOW RISK CONTRACTS (APR 2010)

H.3 1352.237-73 FOREIGN NATIONAL VISITOR AND GUEST ACCESS TO DEPARTMENTAL RESOURCES (APR 2010)..25

SECTION I CONTRACT CLAUSES

I.1 52.202-1 DEFINITIONS (NOV 2013)

I.2 52.203-3 GRATUITIES (APR 1984)

I.3 52.203-5 COVENANT AGAINST CONTINGENT FEES (MAY 2014)

I.4 52.203-6 RESTRICTIONS ON SUBCONTRACTOR SALES TO THE GOVERNMENT (SEP 2006)

I.5 52.203-7 ANTI-KICKBACK PROCEDURES (MAY 2014)

I.6 52.203-10 PRICE OR FEE ADJUSTMENT FOR ILLEGAL OR IMPROPER ACTIVITY (MAY 2014)

I.7 52.203-12 LIMITATION ON PAYMENTS TO INFLUENCE CERTAIN FEDERAL TRANSACTIONS (OCT 2010)

I.8 52.204-4 PRINTED OR COPIED DOUBLE-SIDED ON POSTCONSUMER FIBER CONTENT PAPER (MAY 2011)

I.9 52.204-9 PERSONAL IDENTITY VERIFICATION OF CONTRACTOR PERSONNEL (JAN 2011)

I.10 52.204-10 REPORTING EXECUTIVE COMPENSATION AND FIRST-TIER SUBCONTRACT AWARDS (OCT 2016)

I.11 52.204-13 SYSTEM FOR AWARD MANAGEMENT MAINTENANCE (OCT 2016)

I.12 52.204-15 SERVICE CONTRACT REPORTING REQUIREMENTS FOR INDEFINITE-DELIVERY CONTRACTS (OCT 2016) 27

I.13 52.209-6 PROTECTING THE GOVERNMENT`S INTEREST WHEN SUBCONTRACTING WITH CONTRACTORS DEBARRED, SUSPENDED, OR PROPOSED FOR DEBARMENT (OCT 2015)

I.14 52.210-1 MARKET RESEARCH (APR 2011)

I.15 52.211-13 TIME EXTENSIONS (SEP 2000)

I.16 52.215-2 AUDIT AND RECORDS--NEGOTIATION (OCT 2010)

I.17 52.215-8 ORDER OF PRECEDENCE--UNIFORM CONTRACT FORMAT (OCT 1997)

I.18 52.215-10 PRICE REDUCTION FOR DEFECTIVE CERTIFIED COST OR PRICING DATA (AUG 2011)

I.19 52.215-11 PRICE REDUCTION FOR DEFECTIVE CERTIFIED COST OR PRICING DATA--MODIFICATIONS (AUG

2011)

PAGE 4 OF 62 SB134118RP0009

I.20 52.215-12 SUBCONTRACTOR CERTIFIED COST OR PRICING DATA (OCT 2010)

I.21 52.215-13 SUBCONTRACTOR CERTIFIED COST OR PRICING DATA--MODIFICATIONS (OCT 2010)

I.22 52.215-15 PENSION ADJUSTMENTS AND ASSET REVERSIONS (OCT 2010)

I.23 52.215-18 REVERSION OR ADJUSTMENT OF PLANS FOR POSTRETIREMENT BENEFITS (PRB) OTHER THAN PENSIONS

(JUL 2005)

I.24 52.215-19 NOTIFICATION OF OWNERSHIP CHANGES (OCT 1997)

I.25 52.215-21 REQUIREMENTS FOR CERTIFIED COST OR PRICING DATA AND DATA OTHER THAN CERTIFIED COST

OR PRICING DATA--MODIFICATIONS (OCT 2010)

I.26 52.217-6 OPTION FOR INCREASED QUANTITY (MAR 1989)

I.27 52.217-7 OPTION FOR INCREASED QUANTITY--SEPARATELY PRICED LINE ITEM (MAR 1989)

I.28 52.219-14 LIMITATIONS ON SUBCONTRACTING (JAN 2017)

I.29 52.222-1 NOTICE TO THE GOVERNMENT OF LABOR DISPUTES (FEB 1997)

I.30 52.222-3 CONVICT LABOR (JUN 2003)

I.31 52.222-4 CONTRACT WORK HOURS AND SAFETY STANDARDS --OVERTIME COMPENSATION (MAY 2014)

I.32 52.222-6 CONSTRUCTION WAGE RATE REQUIREMENTS (MAY 2014)

I.33 52.222-7 WITHHOLDING OF FUNDS (MAY 2014)

I.34 52.222-8 PAYROLLS AND BASIC RECORDS (MAY 2014)

I.35 52.222-9 APPRENTICES AND TRAINEES (JUL 2005)

I.36 52.222-10 COMPLIANCE WITH COPELAND ACT REQUIREMENTS (FEB 1988)

I.37 52.222-11 SUBCONTRACTS (LABOR STANDARDS) (MAY 2014)

I.38 52.222-12 CONTRACT TERMINATION--DEBARMENT (MAY 2014)

I.39 52.222-13 COMPLIANCE WITH CONSTRUCTION WAGE RATE REQUIREMENTS AND RELATED REGULATIONS (MAY

2014)

I.40 52.222-14 DISPUTES CONCERNING LABOR STANDARDS (FEB 1988)

I.41 52.222-15 CERTIFICATION OF ELIGIBILITY (MAY 2104)

I.42 52.222-21 PROHIBITION OF SEGREGATED FACILITIES (APR 2015)

I.43 52.222-26 EQUAL OPPORTUNITY (SEPT 2016)

I.44 52.222-27 AFFIRMATIVE ACTION COMPLIANCE REQUIREMENTS FOR CONSTRUCTION (APR 2015)

I.45 52.222-35 EQUAL OPPORTUNITY FOR VETERANS. [OCT 2015]

I.46 52.222-37 EMPLOYMENT REPORTS ON VETERANS (FEB 2016)

I.47 52.222-50 COMBATING TRAFFICKING IN PERSONS (MAR 2015)

I.48 52.222-54 EMPLOYMENT ELIGIBILITY VERIFICATION (OCT 2015)

I.49 52.223-2 AFFIRMATIVE PROCUREMENT OF BIOBASED PRODUCTS UNDER SERVICE AND CONSTRUCTION CONTRACTS

(SEP 2013)

I.50 52.223-3 HAZARDOUS MATERIAL IDENTIFICATION AND MATERIAL SAFETY DATA (JAN 1997)

I.51 52.223-5 POLLUTION PREVENTION AND RIGHT-TO-KNOW INFORMATION (MAY 2011)

I.52 52.223-6 DRUG-FREE WORKPLACE (MAY 2001)

I.53 52.223-17 AFFIRMATIVE PROCUREMENT OF EPA-DESIGNATED ITEMS IN SERVICE AND CONSTRUCTION CONTRACTS

(MAY 2008)

I.54 52.223-18 ENCOURAGING CONTRACTOR POLICIES TO BAN TEXT MESSAGING WHILE DRIVING (AUG 2011)

I.55 52.225-13 RESTRICTIONS ON CERTAIN FOREIGN PURCHASES (JUN 2008)

I.56 52.227-1 AUTHORIZATION AND CONSENT (DEC 2007)

I.57 52.227-2 NOTICE AND ASSISTANCE REGARDING PATENT AND COPYRIGHT INFRINGEMENT (DEC 2007)

I.58 52.227-4 PATENT INDEMNITY--CONSTRUCTION CONTRACTS (DEC 2007)

I.59 52.228-2 ADDITIONAL BOND SECURITY (OCT 1997)

I.60 52.228-5 INSURANCE--WORK ON A GOVERNMENT INSTALLATION (JAN 1997)

I.61 52.228-11 PLEDGES OF ASSETS (JAN 2012)

I.62 52.228-12 PROSPECTIVE SUBCONTRACTOR REQUESTS FOR BONDS (MAY 2014)

I.63 52.228-13 ALTERNATIVE PAYMENT PROTECTIONS (JUL 2000)

I.64 52.228-15 PERFORMANCE AND PAYMENT BONDS--CONSTRUCTION (OCT 2010)

I.65 52.229-3 FEDERAL, STATE, AND LOCAL TAXES (FEB 2013)

PAGE 5 OF 62 SB134118RP0009

I.66 52.232-27 PROMPT PAYMENT FOR CONSTRUCTION CONTRACTS (JAN 2017)

I.67 52.233-1 DISPUTES (MAY 2014)

I.68 52.233-3 PROTEST AFTER AWARD (AUG 1996)

I.69 52.233-4 APPLICABLE LAW FOR BREACH OF CONTRACT CLAIM (OCT 2004)

I.70 52.236-2 DIFFERING SITE CONDITIONS (APR 1984)

I.71 52.236-3 SITE INVESTIGATION AND CONDITIONS AFFECTING THE WORK (APR 1984)

I.72 52.236-5 MATERIAL AND WORKMANSHIP (APR 1984)

I.73 52.236-6 SUPERINTENDENCE BY THE CONTRACTOR (APR 1984)

I.74 52.236-7 PERMITS AND RESPONSIBILITIES (NOV 1991)

I.75 52.236-8 OTHER CONTRACTS (APR 1984)

I.76 52.236-9 PROTECTION OF EXISTING VEGETATION, STRUCTURES, EQUIPMENT, UTILITIES, AND IMPROVEMENTS

(APR 1984)

I.77 52.236-10 OPERATIONS AND STORAGE AREAS (APR 1984)

I.78 52.236-11 USE AND POSSESSION PRIOR TO COMPLETION (APR 1984)

I.79 52.236-12 CLEANING UP (APR 1984)

I.80 52.236-13 ACCIDENT PREVENTION (NOV 1991)

I.81 52.236-13 I ACCIDENT PREVENTION (NOV 1991)--ALTERNATE I (NOV 1991)

I.82 52.236-14 AVAILABILITY AND USE OF UTILITY SERVICES (APR 1984)

I.83 52.236-15 SCHEDULES FOR CONSTRUCTION CONTRACTS (APR 1984)

I.84 52.236-17 LAYOUT OF WORK (APR 1984)

I.85 52.236-21 SPECIFICATIONS AND DRAWINGS FOR CONSTRUCTION (FEB 1997)

I.86 52.236-26 PRECONSTRUCTION CONFERENCE (FEB 1995)

I.87 52.242-13 BANKRUPTCY (JUL 1995)

I.88 52.243-4 CHANGES (JUN 2007)

I.89 52.243-5 CHANGES AND CHANGED CONDITIONS (APR 1984)

I.90 52.245-1 GOVERNMENT PROPERTY (JAN 2017)

I.91 52.245-1 I GOVERNMENT PROPERTY (JAN 2017)--ALTERNATE I (APR 2012)

I.92 52.245-9 USE AND CHARGES (APR 2012)

I.93 52.246-21 WARRANTY OF CONSTRUCTION (MAR 1994)

I.94 52.248-3 VALUE ENGINEERING--CONSTRUCTION (OCT 2015)

I.95 52.249-2 I TERMINATION FOR CONVENIENCE OF THE GOVERNMENT (FIXED-PRICE) (APR 2012)-- ALTERNATE

I (SEP 1996)

I.96 52.249-10 DEFAULT (FIXED-PRICE CONSTRUCTION) (APR 1984)

I.97 52.203-8 CANCELLATION, RESCISSION, AND RECOVERY OF FUNDS FOR ILLEGAL OR IMPROPER ACTIVITY (MAY

2014)

I.98 52.203-13 CONTRACTOR CODE OF BUSINESS ETHICS AND CONDUCT (OCT 2015)

I.99 52.203-14 DISPLAY OF HOTLINE POSTER(S) (OCT 2015)

I.100 52.211-12 LIQUIDATED DAMAGES--CONSTRUCTION (SEP 2000)

I.101 52.216-18 ORDERING (OCT 1995)

I.102 52.216-19 ORDER LIMITATIONS (OCT 1995)

I.103 52.216-22 INDEFINITE QUANTITY (OCT 1995)

I.104 52.217-8 OPTION TO EXTEND SERVICES (NOV 1999)

I.105 52.219-8 UTILIZATION OF SMALL BUSINESS CONCERNS (NOV 2016)

I.106 52.219-17 SECTION 8(a) AWARD (JAN 2017)

I.107 52.219-18 I NOTIFICATION OF COMPETITION LIMITED TO ELIGIBLE 8(A) PARTICIPANTS (JAN 2017)--

ALTERNATE I (JAN 2017)

I.108 52.222-23 NOTICE OF REQUIREMENT FOR AFFIRMATIVE ACTION TO ENSURE EQUAL EMPLOYMENT OPPORTUNITY

FOR CONSTRUCTION (FEB 1999)

I.109 52.225-9 BUY AMERICAN--CONSTRUCTION MATERIALS (MAY 2014)

I.110 52.228-1 BID GUARANTEE (SEP 1996)

I.111 52.232-40 PROVIDING ACCELERATED PAYMENTS TO SMALL BUSINESS SUBCONTRACTORS (DEC 2013)

PAGE 6 OF 62 SB134118RP0009

I.112 52.252-2 CLAUSES INCORPORATED BY REFERENCE (FEB 1998)

I.113 1352.209-73 COMPLIANCE WITH THE LAWS (APR 2010)

I.114 1352.209-74 ORGANIZATIONAL CONFLICT OF INTEREST (APR 2010)

I.115 1352.219-71 NOTIFICATION TO DELAY PERFORMANCE (DEVIATION) (APR 2010)

I.116 1352.219-72 NOTIFICATION OF COMPETITION LIMITED TO ELIGIBLE 8(a) CONCERNS, ALTERNATE III

(DEVIATION) (APR 2010)

SECTION J LIST OF ATTACHMENTS

J.1 List of Attachments

SECTION K REPRESENTATIONS, CERTIFICATIONS AND OTHER STATEMENTS OF OFFERORS

K.1 52.204-17 OWNERSHIP OR CONTROL OF OFFEROR (JUL 2016)

K.2 52.209-5 CERTIFICATION REGARDING RESPONSIBILITY MATTERS (OCT 2015)

K.3 52.223-4 RECOVERED MATERIAL CERTIFICATION (MAY 2008)

K.4 52.225-25 PROHIBITION ON CONTRACTING WITH ENTITIES ENGAGING IN CERTAIN ACTIVITIES OR TRANSACTIONS

RELATING TO IRAN--REPRESENTATION AND CERTIFICATIONS (OCT 2015)

K.5 52.204-8 ANNUAL REPRESENTATIONS AND CERTIFICATIONS (JAN 2018)

K.6 52.204-20 PREDECESSOR OF OFFEROR (JUL 2016)

SECTION L INSTRUCTIONS, CONDITIONS, AND NOTICES TO OFFERORS

L.1 Instructions to Offerors

L.2 52.204-7 SYSTEM FOR AWARD MANAGEMENT (OCT 2016)

L.3 52.204-16 COMMERCIAL AND GOVERNMENT ENTITY CODE REPORTING (JUL 2016)

L.4 52.204-18 COMMERCIAL AND GOVERNMENT ENTITY CODE MANAGEMENT (JUL 2016)

L.5 52.216-1 TYPE OF CONTRACT (APR 1984)

L.6 52.216-27 SINGLE OR MULTIPLE AWARDS (OCT 1995)

L.7 52.225-10 NOTICE OF BUY AMERICAN REQUIREMENT--CONSTRUCTION MATERIALS (MAY 2014)

L.8 52.233-2 SERVICE OF PROTEST (SEP 2006)

L.9 52.236-27 SITE VISIT (CONSTRUCTION) (FEB 1995)

L.10 52.236-28 PREPARATION OF PROPOSALS--CONSTRUCTION (OCT 1997)

L.11 1352.233-70 AGENCY PROTESTS (APR 2010)

L.12 1352.233-71 GAO AND COURT OF FEDERAL CLAIMS PROTESTS (APR 2010)

L.13 1352.242-70 POSTAWARD CONFERENCE (APR 2010)

SECTION M EVALUATION FACTORS FOR AWARD

M.1 Basis for Award

PAGE 7 OF 62 SB134118RP0009

SECTION B

SUPPLIES OR SERVICES AND PRICES/COSTS

B.1 1352.216-75 MINIMUM AND MAXIMUM CONTRACT AMOUNTS (APR 2010)

During the term of the contract, the Government shall place orders totaling a minimum of $1,000 .

The amount of all orders shall not exceed $9,999,999 .

(End of clause)

PAGE 8 OF 62 SB134118RP0009

SECTION C

DESCRIPTION/SPECIFICATIONS/WORK STATEMENT

PAGE 9 OF 62 SB134118RP0009

C.1 Statement of Work

STATEMENT OF WORK

FOR

Multiple Award Construction Contract

PART 1 GENERAL

1.1. General: It is the intent of this Statement of Work (SOW) is to define the requirements for the National Institute of Standards and Technology (NIST) Indefinite Delivery Indefinite Quantity (IDIQ) Multiple Award Construction Contact (MACC) at the NIST Boulder Campus and Fort Collins Site. The SOW identifies the requirements of the MACC and the procedures for soliciting, selecting and awarding IDIQ task orders. The MACC scope of work is for design-bid-build (DBB) projects involving construction and demolition work. The project requirements may involve minimal design work that is incidental to the construction work or basic design work for non-complex projects. The scope of work includes construction, maintenance, repair, equipment installation, sustainment, restoration / modernization and demolition.

1.2. Location: The Department of Commerce (DOC) site campus is located at 325 Broadway in Boulder, Colorado. The requirements, as presented in this document, along with any attachments, are intended to describe the minimum Government requirements.

1.3. Total Contract Value and Period of Performance: The total maximum quantity to be ordered is $9,999,000 for the length of the contract, not to exceed five years. The maximum quantity is calculated as the sum of all task orders (TO) issued, including modifications, to all the MACC contractors.

1.4. See the General Instructions (Attachment 1) for Construction/Maintenance Activities for conducting work included in the contract for information on rules and requirements of performing work on the sites in Boulder and Ft. Collins, Colorado.

PART 2 BACKGROUND

2.1 The NIST Office of Facilities and Property Management (OFPM) manages and provides services to the DOC staff in support of their research, technical, and administrative programs. DOC agencies serviced by OFPM Boulder include, but are not limited to NIST and the National Telecommunications and Information Administration (NTIA).

2.2 The facilities consist of scientific research facilities and radio transmission sites. The facilities are made up of approximately 30 different buildings (approx. 650,000 sq. ft.), which consist of scientific research laboratories and clean-rooms, warehouses, machine shops, maintenance shops, a central utility plant, administrative offices, and conference / auditorium spaces. The age of the facilities range from late 1950’s to recent technology and construction. These sites are located in Boulder and Fort Collins, Colorado. The majority of the work is expected to be at the NIST facility in Boulder, CO with minimal amount expected to be in the Fort. Collins, CO.

PAGE 10 OF 62 SB134118RP0009

2.3 The Contractor shall furnish all management, supervision, labor, materials, equipment, and incidentals required for a broad range of maintenance, repair, and construction work on various real property facilities at installations covered under this contract as design-bid-build projects. The Contractor shall principally perform construction only. Drawings, specifications, and other data for and preliminary to the construction are prepared by the Government; the contract is only for the construction of the project. Project requirements may involve minimal design and/or other engineering services work that is incidental to the construction work, or basic design work for non-complex projects.

2.4 The MACC scope of work includes architectural, mechanical, electrical and civil works for projects in support of facility investment such as facility and built-in equipment repair, construction, maintenance, equipment installation, sustainment, restoration / modernization, new footprint and demolition. The Contractor shall furnish all labor, management, supervision, tools, materials, equipment, engineering, and transportation, except otherwise specified herein, necessary to perform various facility and build-in equipment type projects.

Work may include hazardous material removal, including asbestos and lead-base paint, and environmental related work. Work will be performed in a scientific and research environment where the facility must remain operational at all times and the impact to the scientific research shall be mitigated/minimized at all times.

PART 3 TASK ORDER GENERAL REQUIREMENTS

3.1 Following award of the IDIQ MACC contracts, NIST will solicit MACC Contractors for TO - Request for Proposals (RFP). Each TO-RFP will identify the proposal submittal date.

TO-RFP periods will normally range between 5 - 30 days, depending on scope, complexity and value of work. Individual TO projects will range in ordering value from $2,000 to $1,250,000. The total maximum quantity to be ordered is $9,999,000 for the length of the contract, not to exceed five years. The maximum quantity is calculated as the sum of all orders issued, including modifications, to all the MACC contractors.

3.2 Contractors are not required to submit a proposal in response to each and every TO- RFP; however, contractors are encouraged to submit a proposal in response to each TO- RFP. If a contractor decides not to submit a proposal for a task order, the contractor SHALL submit a written notification to the CO of its intent to decline proposal submission including a brief explanation for declining. The written notification must be submitted by the TO-RFP proposal submittal date/time.

3.3 Task Orders may be evaluated and awarded on the basis of a Price Only method; a Lowest Price Technically Acceptable (LPTA) method; or a Best Value-Trade Offs method across the best value continuum. If the Government decides to issue the task order as a best value, the TO-RFP will identify factors, submittal requirements and the basis of evaluation.

Factors will vary depending on the unique requirements for each TO.

3.4 The Government reserves the right to accept other than the lowest price offer. The TO-RFP will describe the relationship between price and other non-price factors considered in TO source selection. When soliciting as best value, the TO-RFP may require submission of a written proposal describing the approach to the proposed project work described in the

PAGE 11 OF 62 SB134118RP0009

Government’s SOW and project drawings, if any. The Contractor’s proposal may be required to include; a written narrative describing their approach to the subject project, drawings to show the intended work, a schedule showing the Contractor’s intended progression, and any permits required.

3.5 The Government intends to award TOs without discussions; however, the Government reserves the right to conduct discussions if it deems appropriate. If discussions are conducted, each offeror will be requested to provide a final proposal, unless eliminated from discussions through the establishment of a competitive range.

3.6 TO competition: TO-RFPs will be competed among the MACC contractors; however, the Government may issue a TO-RFP to only one contractor in the following situations:

a. The work is specialized and one Contractor possesses a clear price advantage for the type of work that would be involved which is unlikely to be overcome by consideration of any other factors.

b. The work requirement is of such urgency that following the procedures set forth in this section, would result in unacceptable delay.

c. Only one Contractor possesses the capability of performing the work.

d. The order is a logical follow-on to an order already issued to a Contractor such that economy and efficiency dictate award to the same Contractor.

e. The order is necessary to meet the Government's minimum guarantee. Should one of the IDIQ contractors be unable to competitively secure a task order to meet the minimum guarantee, then the Government reserves the right to solicit and negotiate a task order with only that offeror.

3.7 The U.S. Government shall not be obligated to reimburse the Contractor for work performed, or any costs incurred, nor shall the Contractor be obligated to perform, or otherwise incur costs except as authorized by duly executed Task Orders. Contractor's costs will not be compensated for participating in site visits and task order proposal.

3.8 A written Task Order will be issued to the Contractor by the Contracting Officer for each project of work to be performed under this contract.

3.9 Task orders may involve trades such as carpentry, plumbing, electrical, mechanical, painting, pipe fitting, sheet metal, welding, roofing, site work, site utilities, excavation, concrete, masonry, pavement repair, asbestos and lead paint removal, security hardware installation, and demolition.

3.10 Task orders may include, but are not limited to, construction/renovation of scientific research laboratory facilities and/or administrative facilities (offices, operation centers, and warehouses); utilities; electrical systems; water systems; sewage systems; ADA compliance

PAGE 12 OF 62 SB134118RP0009

requirements; safety systems such as fall protection devices / guardrails; solar/energy conservation systems; roofs; communications; security systems; radio transmission towers;

HVAC systems; roads; fences; and gates. Activities may consist of but are not limited to:

a. Construction services including site renovations and renovations of existing labs and offices up to and including the complete strip out of selected areas and the reconstruction of new labs and offices in facilities built as long ago as the early 1950’s.

b. Structural demolition and construction including foundations, concrete, steel and other materials used in the construction trades.

c. Mechanical demolition and construction including energy conservation, heating and ventilation, air conditioning, plumbing, fire protection, alarms, sprinkler systems, special mechanical systems and process systems. May include the repair, replacement, and or upgrading of mechanical systems or equipment including controls.

d. Electrical construction including power service and distribution, lighting, telephones, fire detection and alarms, security systems, electronic communications, special electrical systems, energy conservation, code analysis, and general space requirements. May include the repair, replacement, and or upgrading of electrical systems or equipment.

e. General excavation including utility systems, water systems, fire protection systems, drainage systems, roads, earthwork and paving, grading, native landscaping, irrigation, landscape, and walkways/bike paths.

f. Disassembling, reassembling and moving of laboratory/office equipment/furniture from one area to a new location and or storage during the activities described in the SOW.

3.11 Task orders will be primarily multiple-craft involving the installation of new equipment, and/or the removal of old or outdated equipment and may involve the repair or modernization of existing equipment within laboratories and surrounding spaces attached to laboratories and offices. In addition, some TOs may involve the complete demolition of an existing space and the build-back of a completely new lab, office, or common space with new materials from the floor to ceiling including lights, air handling and temperature control systems, along with any specialized connections to support the lab function such as chilled water, low/high pressure air, special electrical requirements, fume hoods, and exhaust fans, etc. TOs may also include the moving and installation of new scientific/electronic equipment and/or the removal of equipment from one area of the site, then moving and installing it at a new, designated location. This will require involvement of contractor personal with the Contracting Officer’s Representative (COR), scientific staff, and possibly the manufacturer of equipment.

3.12 Work requirements may involve work in and around occupied areas performing scientific/research experiments where vibration, noise, dust, outages of utilities and/or disturbances to the physical environment will hinder the ability of the Government to perform required activities. ALL activities must be planned, scheduled and coordinated with the COR in order to be posted for a minimum of two weeks prior to the activity beginning. Flexibility

PAGE 13 OF 62 SB134118RP0009

may be required for certain activities and may have to be performed out of normal business hours, such as concrete sawing, hammer drilling, utility shutdown and/or other activities which may cause disturbances and interrupt normal activities.

3.13 Contracting Officer’s Representative (COR): The Government will designate a single specific COR for the IDIQ MACCs. The Government will assign a specific COR for each TO.

In the event that a COR is not designated for a task order upon award, then the MACC COR will serve as the COR for the TO.

3.14 Bonds: The contractor shall submit Performance and Payment Bonds for awarded TOs only. The Contractor shall ensure the MACC number and the TO number are included on each Performance and Payment Bond.

3.15 Liquidated damages: Liquidated damages will be identified for each specific TO in the

TO-RFP.

3.16 Precedence: In the event that the RFP or contract requirements of a TO conflict with the requirements of the basic MACC, the TO requirements take precedence over that of the MACC requirements.

PART 4 TASK ORDER SOLICITATION AND PROPOSAL

4.1 Task Order Request for Proposal: When the Government requires work under the MACC, a TO-RFP will be issued to the MACC contractors. The TO-RFP will include an electronic copy of the SOW, and if applicable, an electronic set of drawings and specifications. The level of the design provided to the Contractor shall be anywhere from a basic concept to a complete design package, depending on the scope and complexity of the requirement. The Contractor may reproduce the drawings and specifications at the Contractor’s own expense. The Contractor shall check all drawings and specifications immediately upon receipt for discrepancies and notify the Contracting Officer (CO) immediately of any/all discrepancies found. Enlarged plans and details shall govern where the same work is shown at smaller scales. The Contractor shall compare all drawings and verify the installation before proceeding with work and shall be responsible for any errors which might have been avoided thereby.

4.2 Site Visit: Depending on the complexity of the project, the Government may conduct a pre-proposal site visit for the TO-RFP. Site Visits are encouraged but are not mandatory.

The Government will not reimburse any expense the contractor incurs in proposal preparation. Site visit discussions may include clarification of: scope of work, method of construction, sequence of operations, progress schedule, means of access to project site, delivery and storage of materials and equipment, work restrictions, coordination requirements, project goals, liquidated damages, and potential difficulties/problems. The Contractor shall email site visit questions to the CO within two (2) workdays following the site visit.

4.3 On-Site Conditions: As-builts / drawings / existing site conditions: As-built drawings will be provided when possible; however, current as-built drawings may not be available.

PAGE 14 OF 62 SB134118RP0009

Drawings showing the location of equipment, piping, ducts and conduit, etc. are diagrammatic and may not show every detail required. In addition, site conditions will not always permit installation in the locations shown. Drawings showing equipment, piping, ducts, conduit, etc., to be removed, altered, or installed, may require deviation from the configuration of the demolition or installation drawings. This may be due to existence of conflicting ducts, conduits, hangers, light fixtures, structural items, and temporary walls, etc. All such minor details of work which are not shown on the drawings, as well as such items not specifically mentioned in the specifications, but which are essential and necessary for the completion of the work, and to make all systems or equipment operational, shall be considered as incidental and shall be included as part of the work. When this situation occurs, the final placement of permanently installed items shall be subject to approval by the CO. The Contractor shall be responsible for inspecting to his satisfaction all areas/items of possible conflict. Failure to verify the dimensions and locations will be at the Contractor's risk and shall not relieve the Contractor from accomplishing the work required by the TO.

4.4 Location of Underground Facilities: Where existing piping, utilities, and underground obstructions of any type are indicated in locations to be traversed by new piping, ducts, and other work provided herein, and such are not indicated or specified to be removed, the elevations of the existing utilities and obstructions shall be verified before the new work is laid closer than the nearest manhole or other structure at which an adjustment in grade could be made. For any additional work required by reason of conflict between the new and existing work, an adjustment in contract price will be made in accordance with Contract Clause entitled "DIFFERING SITE CONDITIONS".

4.5 All proposals shall include, at a minimum, a cover page, the firm-fixed price, assumptions, performance period, any special considerations such as request for winter exclusion, phasing of construction, operational concerns, etc. The Contractor’s proposals shall be complete and concise.

4.6 For non-complex projects, the Government may require, as part of the proposal, a basic design concept or solution. Design concepts and drawings shall be sufficient to substantiate the proposed approach for the TO and shall be compliant with all applicable building and construction codes. In the RFQ, the Government will identify the extent of documentation that the Contractor shall include in the TO proposal.

4.7 For TOs involving incidental design work or non-complex TOs involving basic concepts or design, the documentation requirements may include calculations to substantiate appropriate equipment or material selection/ sizing, component assembly, and proposed layout and sizing of utilities and structural elements. The Contractor shall (if applicable) supply the following calculations:

a.i. Mechanical: HVAC load analysis and unit sizing, pipe sizing, and duct sizing.

a.ii. Electrical: Electrical system capacity, conductor, conduit, protective devices, and other equipment sizing.

a.iii. Structural: Structural system and foundation sizing.

a.iv. Pavement/Site Work: Area run-off quantities, drainage capacities, and grading slopes.

a.v. Energy: Energy savings and Return on Investment (ROI), if applicable.

PAGE 15 OF 62 SB134118RP0009

PART 5 SUBMITTALS REQUIRING CO APPROVAL

5.1 Contractor shall provide the following submittals to the COR for coordination of CO approval:

a. A construction schedule is required for projects with a continuous performance period of 60 days or more, unless otherwise required by the TO SOW.

b. In addition to the construction schedule, the Contractor shall be required to submit a critical path Gantt chart schedule with milestones for all projects with a performance period of 90 days or more.

c. Submittals, as identified in each TO requirement, in the contract drawings and specifications from the following divisions (as applicable to the TO):

Division 00 - Procurement and Contracting Requirements Division 01 - General Requirements Division 02 - Existing Conditions Division 03 - Concrete Division 04 - Masonry Division 05 - Metals Division 06 - Wood, Plastics, Composites Division 07 - Thermal and Moisture Protection Division 08 - Openings Division 09 - Finishes Division 10 - Specialties Division 11 - Equipment Division 12 - Furnishings Division 13 - Special Construction Division 14 - Conveying Equipment Division 21 - Fire Suppression Division 22 - Plumbing Division 23 - Heating, Ventilating, and Air Conditioning (HVAC) Division 25 - Integrated Automation Division 26 - Electrical Division 27 - Communications Division 28 - Electronic Safety and Security Division 31 - Earthwork Division 32 - Exterior Improvements Division 33 – Utilities

d. Certified Shop Drawings. Shop drawings shall show in detail the proposed fabrication and assembly of structural elements and/or the installation (i.e., form, fit, and attachment details) of materials or equipment.

PAGE 16 OF 62 SB134118RP0009

e. Contractor shall provide submittals through a NIST approved, secure electronic site accessible by NIST and Design team responsible for construction administration.

f. Additional items may require engineering approval as applicable to the scope of the TO.

PART 6 EXECUTION

6.1 Pre-Performance Construction Meeting: Before work begins on this contract, the CO will arrange for a meeting with the Contractor to discuss the contract. This discussion may include general requirements including administrative matters, project requirements, submittal procedures, approval and payment schedule, quality control expectations, request for proposal and TO procedures, traffic control, construction access requirements, as-built criteria, performance requirements, security procedures, accident prevention, safety, and fire prevention briefings.

6.2 Business Telephone: At the beginning of this contract, the Contractor shall provide the applicable CO a Contractor personnel telephone number, e-mail, and website for regular working hours. The Contractor shall also provide after hours (emergency) telephone numbers for the Program Manager and Installation Construction Manager, as a minimum. The Contractor shall provide the CO with an updated phone list whenever changes in personnel or phone numbers occur. The Contractor is required to provide a means of mobile communications (i.e., cellular phone and/or pager) for the Program Manager and Installation Construction Manager, Superintendent, Quality Control Officer, and their respective alternates, for the life of the contract. Communications equipment will require special coordination and clearance with installation communications authorities.

6.3 Applicable Codes: The International Code Council (ICC) shall be used, in the most current version, as the standard building code for all construction under this contract. The ICC website is http://www.iccsafe.org/. Any and all changes to the ICC will immediately become requirements of this contract.

6.4 Fire Protection: The Contractor shall be responsible for furnishing adequate and proper fire protection for all phases of the contract work in accordance with ICC and National Fire Protection Agency (NFPA) standards.

6.5 Record Drawings: During the progress of the contract, the Contractor shall keep a set of red-line drawings on the job site. Red-line drawings shall be based on the design drawings provided by the Contractor. These drawings shall be used to create As-builts. If the Contractor fails to maintain the record drawings as required herein, the Contracting Officer will consider that satisfactory progress has not been achieved for the period in question. Final payment will be withheld until As-Built record drawings are submitted and approved by the

CO.

6.6 Salvageable Items: All materials removed and not reused in the project as specified herein or as required by the project SOW, drawings, or specifications, remain the property of

PAGE 17 OF 62 SB134118RP0009

the Government. The Contracting Officer will determine if these materials are salvageable or unsalvageable.

6.7 Electronic Documents and Correspondence:

a. The Contractor shall submit all documents electronically. Electronic file type shall be as indicated by the Contracting Officer. This requirement is in addition to any other requirement throughout this contract. If any other specification or section requires hard copy documents, the Contractor shall submit these documents in both hardcopy and electronic copy to the contracting officer.

b. All documents submitted by the Contractor requiring a signature shall be submitted to the contracting officer with an electronic digital signature. All documents submitted by the Contractor requiring further action and signature by the Government shall be capable of being digitally signed and saved by the Government representative(s) as required.

c. All documents submitted by the Contractor shall follow a standardized file naming convention as indicated herewith. File naming conventions shall be strictly adhered to and may only be modified by the contracting officer. File names shall have no spaces. The following items in the below naming conventions are defined as followed:

c.i. XXXXXX = Contract number as defined by the CO c.ii. YYYYMMDD = Effective date of document or report c.iii. ZZZ = Contractor’s Name Initials c.iv. 001 = Submittal Number or Serial Report Number

d. Submittals:

d.i. [XXXXXX-FORM#-001(Brief Description of Submittal)] Example: 152579- AF3000-004(Ceramic Tile) d.ii. [XXXXXX-SUB-001-Information Type-(Brief Description of Submittal)] Example:

152579-SUB-004-Product Data (Ceramic Tile)

e. RFIs:

e.i. [XXXXXX-RFI-001(Brief Description of RFI)]

f. Daily Reports:

f.i. [XXXXXX-DailyReport-001-YYYYMMDD]

g. Progress Reports:

g.i. [XXXXXX-PR-001-YYYYMMDD]

PAGE 18 OF 62 SB134118RP0009

h. Proposals:

h.i. [XXXXXX-Proposal#-ZZZ-DocumentDescription] h.ii. Examples:

h.iii. XXXXXX-Proposal1-ABC-PDFEstimate h.iv. XXXXXX-Proposal1-ABC-E4CEstimate h.v. XXXXXX-Proposal1-ABC-Narrative h.vi. XXXXXX-Proposal1-ABC-Schedule h.vii. XXXXXX-Proposal1-ABC-NPIQuote(CBAPlumbing)

i. Real Property Documents:

i.i. [XXXXXX-DD1354-Original] [XXXXXX-DD1354-Revision1]

j. Other Miscellaneous Documents/Reports:

j.i. [XXXXXX-FormName,Number,OrDescription-YYYYMMDD]

k. Electronic Correspondence (e-mail) k.i. All electronic correspondence from the Contractor regarding a specific project shall follow a standardized subject line naming convention. File naming conventions shall be strictly adhered to and may only be modified by the contracting officer.

k.ii. Subject Line for all electronic correspondence shall be as follows:

k.iii. XXXXXX-Project Title: Subject of E-mail k.iv. Examples:

k.v. 142523-Renovate Office B1234: Submittal 004 (Ceiling Tile) k.vi. 152538-Construct Addition to B4321: Proposal 1, XYZ Construction Co k.vii. 162542-Demo B0321: Preconstruction Meeting Minutes 20150327

End of Document

PAGE 19 OF 62 SB134118RP0009

SECTION E

INSPECTION AND ACCEPTANCE

E.1 52.246-12 INSPECTION OF CONSTRUCTION (AUG 1996)

(a) "Definition." "Work" includes, but is not limited to, materials, workmanship, and manufacture and fabrication of components.

(b) The Contractor shall maintain an adequate inspection system and perform such inspections as will ensure that the work performed under the contract conforms to contract requirements. The Contractor shall maintain complete inspection records and make them available to the Government. All work shall be conducted under the general direction of the Contracting Officer and is subject to Government inspection and test at all places and at all reasonable times before acceptance to ensure strict compliance with the terms of the contract.

(c) Government inspections and tests are for the sole benefit of the Government and do not--

(1) Relieve the Contractor of responsibility for providing adequate quality control measures;

(2) Relieve the Contractor of responsibility for damage to or loss of the material before acceptance;

(3) Constitute or imply acceptance; or

(4) Affect the continuing rights of the Government after acceptance of the completed work under paragraph (i) of this section.

(d) The presence or absence of a Government inspector does not relieve the Contractor from any contract requirement, nor is the inspector authorized to change any term or condition of the specification without the Contracting Officer`s written authorization.

(e) The Contractor shall promptly furnish, at no increase in contract price, all facilities, labor, and material reasonably needed for performing such safe and convenient inspections and tests as may be required by the Contracting Officer. The Government may charge to the Contractor any additional cost of inspection or test when work is not ready at the time specified by the Contractor for inspection or test, or when prior rejection makes reinspection or retest necessary. The Government shall perform all inspections and tests in a manner that will not unnecessarily delay the work.

Special, full size, and performance tests shall be performed as described in the contract.

(f) The Contractor shall, without charge, replace or correct work found by the Government not to conform to contract requirements, unless in the public interest the Government consents to accept the work with an appropriate adjustment in contract price. The Contractor shall promptly segregate and remove rejected material from the premises.

(g) If the Contractor does not promptly replace or correct rejected work, the Government may--

(1) By contract or otherwise, replace or correct the work and charge the cost to the Contractor;

or

(2) Terminate for default the Contractor`s right to proceed.

(h) If, before acceptance of the entire work, the Government decides to examine already completed work by removing it or tearing it out, the Contractor, on request, shall promptly furnish all necessary facilities, labor, and material. If the work is found to be defective or nonconforming in any material respect due to the fault of the Contractor or its subcontractors, the Contractor shall defray the expenses of the examination and of satisfactory reconstruction. However, if the work is found to meet contract requirements, the Contracting Officer shall make an equitable adjustment for the additional services involved in the examination and reconstruction, including, if completion of the work was thereby delayed, an extension of time.

(i) Unless otherwise specified in the contract, the Government shall accept, as promptly as practicable after completion and inspection, all work required by the contract or that portion of the work the Contracting Officer determines can be accepted separately. Acceptance shall be final and conclusive except for latent defects, fraud, gross mistakes amounting to fraud, or the Government`s rights under any warranty or guarantee.

(End of Clause)

PAGE 20 OF 62 SB134118RP0009

SECTION F

DELIVERIES OR PERFORMANCE

F.1 52.211-10 COMMENCEMENT, PROSECUTION, AND COMPLETION OF WORK (APR 1984)

The Contractor shall be required to

(a) commence work under this contract within 10 calendar days after the date the Contractor receives the notice to proceed,

(b) prosecute the work diligently, and

(c) complete the entire work ready for use not later than the number of days or date specified in the task order The time stated for completion shall include final cleanup of the premises.

F.2 52.242-14 SUSPENSION OF WORK (APR 1984)

(a) The Contracting Officer may order the Contractor, in writing, to suspend, delay, or interrupt all or any part of the work of this contract for the period of time that the Contracting Officer determines appropriate for the convenience of the Government.

(b) If the performance of all or any part of the work is, for an unreasonable period of time, suspended, delayed, or interrupted

(1) by an act of the Contracting Officer in the administration of this contract, or

(2) by the Contracting Officer`s failure to act within the time specified in this contract (or within a reasonable time if not specified), an adjustment shall be made for any increase in the cost of performance of this contract (excluding profit) necessarily caused by the unreasonable suspension, delay, or interruption, and the contract modified in writing accordingly. However, no adjustment shall be made under this clause for any suspension, delay, or interruption to the extent that performance would have been so suspended, delayed, or interrupted by any other cause, including the fault or negligence of the Contractor, or for which an equitable adjustment is provided for or excluded under any other term or condition of this contract.

(c) A claim under this clause shall not be allowed--

(1) For any costs incurred more than 20 days before the Contractor shall have notified the Contracting Officer in writing of the act or failure to act involved (but this requirement shall not apply as to a claim resulting from a suspension order); and

(2) Unless the claim, in an amount stated, is asserted in writing as soon as practicable after the termination of the suspension, delay, or interruption, but not later than the date of final payment under the contract.

PAGE 21 OF 62 SB134118RP0009

SECTION G

CONTRACT ADMINISTRATION DATA

G.1 52.232-5 PAYMENTS UNDER FIXED-PRICE CONSTRUCTION CONTRACTS (MAY 2014)

(Reference 52.232-5)

G.2 52.232-17 INTEREST (MAY 2014)

(Reference 52.232-17)

G.3 52.232-23 ASSIGNMENT OF CLAIMS (MAY 2014)

(Reference 52.232-23)

G.4 52.232-33 PAYMENT BY ELECTRONIC FUNDS TRANSFER--SYSTEM FOR AWARD MANAGEMENT (JUL 2013) (Reference 52.232-33)

G.5 1352.201-70 CONTRACTING OFFICER?s AUTHORITY (APR 2010)

The Contracting Officer is the only person authorized to make or approve any changes in any of the requirements of this contract, and, notwithstanding any provisions contained elsewhere in this contract, the said authority remains solely in the Contracting Officer. In the event the contractor makes any changes at the direction of any person other than the Contracting Officer, the change will be considered to have been made without authority and no adjustment will be made in the contract terms and conditions, including price.

G.6 1352.201-72 CONTRACTING OFFICER`S REPRESENTATIVE (COR) (APR 2010)

(a) As determined by separate letter is hereby designated as the Contracting Officer`s Representative (COR). The COR may be changed at any time by the Government without prior notice to the contractor by a unilateral modification to the contract. The COR is located at:

See Section 3.13 of the Statement of Work

Phone Number:

Email:

(b) The…