Attachment C-DRAFT 2012 Fed Std 833F Bus Options Appendix A Specifications 06.24.2011.pdf
Federal Standard Rev. F, Jun 24, 2011 PDF 142 KB Posted
- Solicitation number
- QMAE-CR-110003-N
- Issued by
-
GSA Federal Acquisition Service
About this file
Attachment C-Bus Standards
View the file
Other versions and copies of FED-STD-833F
Show all 20
Who attaches FED-STD-833F
| Agency | Files |
|---|---|
| GSA Federal Acquisition Service | 145 |
Other files
Show all 47
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
Federal Standard 833F, Appendix A
3.0 Requirements
3.25 Options
All options below are identified first by their grouping then code and followed by definition of requirement when selected. Options are requirements that may be selected to modify the standard configuration bus. These Options do not supersede, relax, or otherwise change the aforementioned minimum requirements unless specifically stated.
3.25.1 Body and Chassis
ACLS – AUTOMATIC CHASSIS LUBRICATION SYSTEM – requires the installation of a central distribution type automatic lubrication system such as Interlube AC1 or higher. System must be capable of supplying all lubrication points of the chassis, suspension, body, and subsystems excluding driveshafts. Distribution unit shall be installed under body in proximity of the battery box or in a location such as in the engine compartment where it will not be subject to road debris. All chassis and suspension spring shackles, spring ends, ball and socket joints, bushings, pins, brake cross-shafts, and slack adjusters shall be a grease requiring type and supplied with a metered amount of lubrication by the system.
3.25.2 Engines
GAS – GASOLINE ENGINE – requires replacing standard diesel with largest available V-8 or V-10 gasoline engine. This option deletes the requirement for the engine block heater, intake air restriction indicator, automatic 5-minute idle shutdown, and shore power requirements if no other alternating current consumer is requested.
YD2 – ENGINE-DIESEL-MIN 190 GHP & 520 LB-FT TORQUE – requires a diesel engine with horsepower minimum of 190 GHP and 520 lb-ft of torque. Included shall be all needed subcomponents to complete the change from the standard offering including transmission and axle that match the engine output. The transmission furnished must be rated to meet the engine output power and torque without the use of torque limiting programming.
YD3- ENGINE-DIESEL-MIN 210 GHP & 520LB-FT TORQUE - requires a diesel engine with horsepower minimum of 210 GHP and 520 lb-ft of torque. Included shall be all needed subcomponents to complete the change from the standard offering including transmission and axle that match the engine output. The transmission furnished must be rated to meet the engine output power and torque without the use of torque limiting programming.
YD3B – ENGINE-DIESEL-MIN 260 GHP & 620LB-FT TORQUE - requires a diesel engine with horsepower minimum of 260 GHP and 620 lb-ft of torque. Included shall be all needed subcomponents to complete the change from the standard offering including transmission and axle that match the engine output. The transmission furnished must be rated to meet the engine output power and torque without the use of torque limiting programming.
YD3C – ENGINE-DIESEL-MIN 260 GHP & 660LB-FT TORQUE - requires a diesel engine with horsepower minimum of 260 GHP and 660 lb-ft of torque. Included shall be all needed subcomponents to complete the change from the standard offering including transmission and axle that match the engine output. The transmission furnished must be rated to meet the engine output power and torque without the use of torque limiting programming.
YD3D- ENGINE-DIESEL-MIN 285 GHP & 860 LB-FT TORQUE – requires a diesel engine with horsepower minimum of 285 GHP and 860 lb-ft of torque. Included shall be all needed subcomponents to complete the change from the standard offering including transmission and axle that match the engine output. The transmission furnished must be rated to meet the engine output power and torque without the use of torque limiting programming.
YD3E – ENGINE-DIESEL-MIN 280 GHP & 660LB-FT TORQUE - requires a diesel engine with horsepower minimum of 280 GHP and 660 lb-ft of torque. Included shall be all needed subcomponents to complete the change from the standard offering including transmission and axle that match the engine output. The transmission furnished must be rated to meet the engine output power and torque without the use of torque limiting programming.
YD3F – ENGINE-DIESEL-MIN 300 GHP & 860 LB-FT TORQUE - requires a diesel engine with horsepower minimum of 280 GHP and 660 lb-ft of torque. Included shall be all needed subcomponents to complete the change from the standard offering including transmission and axle that match the engine output. The transmission furnished must be rated to meet the engine output power and torque without the use of torque limiting programming.
3.25.3 Alternative Fuel Engines
E85- ETHANOL FLEXIBLE FUEL – requires adding the ability for the primary propulsion engine to use a fuel mixture containing as much as 85% ethanol and 15% gasoline and commonly known as E85 in the United States. This option requires first selecting the gasoline engine option GAS which replaces the standard equipment diesel engine with one that operates on commercially available gasoline. Option E85 is the incremental difference between option GAS and the addition of being a flex-fuel capable vehicle.
CNG- DEDICATED COMPRESSED NATURAL GAS - requires a dedicated, compressed natural gas engine and fuel system in place of standard diesel-fueled engine. The fuel system and installation shall comply with all applicable FMVSS, FMCSR, and National Fire Code requirements. The storage cylinders shall equal not less than 7600 SCF. Some options may not be available in conjunction with this engine choice.
EPF – ENGINE PROPANE FUELED – requires replacing the standard equipment diesel engine with a direct-injected, dedicated, propane fueled engine and all subsystems required. This option deletes the requirement for the engine block heater, intake air restriction indicator, automatic 5-minute idle shutdown, and shore power requirements if no other alternating current consumer is requested. Option EPF is the incremental difference of replacing the standard diesel engine with a spark ignition engine designed to operate solely on propane fuel and includes any and all storage vessels and controls to complete the modification. Some options may not be available in conjunction with this engine choice.
HEV- HYBRID ELECTRIC VEHICLE – propulsion system includes an internal combustion engine (ICE) powered by gasoline, diesel or other alternative fuel powered combined with electric motor(s), motor controllers and batteries. The engine and electric motor may be connected in either series or parallel configurations. The hybrid system shall include regeneration, a feature that converts inertia into electric energy to charge the hybrid batteries during vehicle deceleration. The horsepower and torque of the standard diesel engine may be reduced. This option deletes the requirement for an automatic 5-minute idle shutdown.
HEV1- HYBRID ELECTRIC PROPULSION AND SUPPORT SYSTEMS –– propulsion system includes an internal combustion engine (ICE) powered by gasoline, diesel or other alternative fuel powered combined with electric motor(s), motor controllers and batteries. The engine and electric motor may be connected in either series or parallel configurations. The hybrid system shall include regeneration, a feature that converts inertia into electric energy to charge the hybrid batteries during vehicle deceleration. The horsepower and torque of the standard diesel engine may be reduced when option HEV1 is selected. The vehicle’s air conditioning and cabin heating systems shall operate on electricity produced by the hybrid system or by a supplemental source while the ICE is off or at idle. This option deletes the requirement for an automatic 5-minute idle shutdown.
HEV2- PLUG-IN HYBRID ELECTRIC VEHICLE - propulsion system includes an internal combustion engine (ICE) powered by gasoline, diesel or other alternative fuel combined with electric motor(s), motor controllers and batteries. The engine and electric motor may be connected in either series or parallel configurations. The hybrid system shall include regeneration, a feature that converts inertia into electric energy to charge the hybrid batteries during vehicle deceleration. The horsepower and torque of the standard engine may be reduced. Required by this configuration is a means to charge the hybrid batteries using shore power while the vehicle is stationary. If the charging cable is typically furnished as part of the Contractor’s package, it must also be furnished to the Government. If a ground based charging station is typically used to charge the batteries, one is not required to be furnished as part of this packaged option. When the shore power cable and connector are typically furnished, it must be included as part of this package.
This option deletes the requirement for an automatic 5-minute idle shutdown.
3.25.4 Engine Accessories
AST- TWO STAGE AIR CLEANER – requires a filter arrangement with a primary and secondary filter or a cyclonic particle diffuser and paper element, combination filter.
EH- ENGINE BLOCK HEATER, OEM - All engines shall be equipped with a 120-volt AC coolant heater located in the engine block. Heater shall be engine manufacturer’s standard or optional equipment.
FFP – HEATER-COOLANT-FUEL FIRED – requires the installation of a fuel-fired engine coolant pre-heater with a minimum of 40,000 BTU output. Heater shall be installed in a dedicated storage box under the bus body. Controls shall be located in the driver’s area. Heater shall be programmable as a pre-heater as well as a heat supplement when the propulsion engine is in use. A third battery isolated from the standard two during engine off shall be located on a slide out tray to be used for engine start if primary batteries are drained.
FFS- FUEL/WATER SEPARATOR, HEATED- requires fuel/water separator with a replaceable filter element or cartridge rated no larger than 30 microns, a drain valve that allows for water and debris to be drained from the lowest point of the unit, a water sensor warning light and heated with thermostatic control.
3.25.5 Transmission
AM6-AUTOMATED MANUAL TRANSMISSION 6-SPEED – requires the substitution of the standard equipment planetary type transmission with an automatic operating clutch and shift manual transmission. The must have no less than six forward speeds. The transmission fluid must be synthetic and meet or exceed the requirements of the transmission manufacturer.
3.25.6 Brakes
BA- BRAKES-AIR – requires upgrade of braking system from hydraulic to drum type air. The system must include the following components:
a. Air Storage Tanks – shall be appropriately rated for application and mounted in such a way to maintain drains at the lowest point for proper water evacuation.
b. Automatic Moisture Ejector – the first air storage tank (wet tank) after the air dryer shall be equipped with a heated, automatic, moisture-ejector. All other air tanks shall be equipped with a brass or stainless steel, ¼-turn ball valve drain. The moisture ejector shall be protected from debris damage or accumulation by shielding.
c. Air Dryer with replaceable, spin-on cartridge, desiccant air dryer; Meritor Model SS1200 or Bendix AD-IP shall be furnished on all air systems and installed per compressor and air dryer manufacturer’s recommendations.
BADA- BRAKES-AIR-DISC-ALL WHEEL ENDS – requires the upgrade to the standard foundation air drum brakes to air discs as all wheel ends. The system must include the following components:
a. Air Storage Tanks – shall be appropriately rated for application and mounted in such a way to maintain drains at the lowest point for proper water evacuation.
d. Automatic Moisture Ejector – the first air storage tank (wet tank) after the air dryer shall be equipped with a heated, automatic, moisture-ejector. All other air tanks shall be equipped with a brass or stainless steel, ¼-turn ball valve drain. The moisture ejector shall be protected from debris damage or accumulation by shielding.
e. Air Dryer with replaceable, spin-on cartridge, desiccant air dryer; Meritor Model SS1200 or Bendix AD-IP shall be furnished on all air systems and installed per compressor and air dryer manufacturer’s recommendations.
3.25.7 Auxiliary Braking
ECB- ENGINE COMPRESSION BRAKE - requires a system that opens all or some of the engine exhaust valves near the end of the compression stroke, thereby converting vehicle motion to a pumping loss (engine compression break). Partial exhaust valve cycle is also acceptable for this function. Operator control shall be a dash mounted switch shall be provided to activate, modulate, or cut the brake augmentation. The switch shall be marked to indicate its position. When active, the system shall be automatically activated by means of conventional driving controls to apply retardation during vehicle deceleration, and deactivate in other operating modes.
EXB – ENGINE EXHAUST BRAKE – requires an exhaust brake installation such as a PAC Brake or a variable pitch turbo charger.
This installation shall be done in compliance with engine manufacturer’s recommendations and include all necessary hardware to complete the installation.
T1-RETARDER-AUTOMATIC TRANSMISSION-INTEGRAL – requires an internal to transmission, fluid operated, driveline retarder included in transmission package. Retarder shall function in a minimum of 3 levels and shall be controlled by the driver with a selector mounted to the upper dash panel in easy access for the driver. Retarder shall activate when throttle is lifted and the unit has been selected on. Engine cooling system shall be upgraded to meet the increased cooling requirements. Additional synthetic transmission fluid needed to fill retarder shall be included in this option.
3.25.8 Drive Axle
AWD- OEM ALL WHEEL DRIVE – requires an all wheel drive chassis in place of the standard two-wheel drive version of the standard unit. If the standard chassis used for the Standard Item Number is not available, an equal model of the same manufacturer must be used in its place. The GSA load and weight capacities must be met or exceeded.
Passenger entrance requirements:
1. The passenger entrance well shall remain as standard construction.
2. The first step height as measured from the ground on a level surface to the top face of the step tread shall not exceed 16-inches.
3. If the tread height is greater than 16-inches an automatic step must be added to reduce height. Subsequent steps shall not exceed 11-inches. The manufacturer will determine the number of steps required to meet the requirement.
DLS- DIFFERENTIAL-LIMITED SLIP – requires substitution of the standard open differential for the axle manufacturer’s slip limiting or locking type differential.
TAA- TRACTION ASSIST-AUTOMATIC - requires a two-wheel spin control system integrated with the brake ABS system.
3.25.9 Electrical
COBB- ONBOARD BATTERY CHARGER – requires a permanently mounted self-regulated charger designed to maintain battery state of charge. The power supply for charger shall be combined with propulsion engine block heater.
MEDS- SWITCH-BATTERY-MASTER-DISCONNECT - requires a manually operated, master-battery disconnect-switch (switch) installed within 18 inches of the battery compartment in a dedicated compartment or located in the battery compartment. A label clearly identifying the location of the switch shall be applied to the exterior surface of the compartment. Attached to or in near proximity to the switch shall be a sticker indicating switch operation. Electrical load carrying device furnished shall be rated at a minimum of 120% continuous, worst-case circuit load. Switch shall be located to be readily distinguishable and provide unimpeded access in an emergency.
3.25.10 Fuel
AF1- CHASSIS MANUFACTURER’S MAXIMUM AVAILABLE FUEL TANK(S) – requires the installation of the chassis manufacturer’s 100 gallon fuel tank.
3.25.11 Exterior
Exterior Luggage Compartments:
a. Multiple storage boxes can be ganged to comply with the following cubic foot requirements.
b. All compartments shall be mounted curbside only.
c. All luggage compartments shall be illuminated and shall have a carpet, rubber, or vinyl covered floor unless made of corrugated aluminum, corrugated stainless steel, or corrugated galvanized steel.
CSU1- COMPARTMENT-STORAGE-UNDERFLOOR-MINIMUM 12 CUBIC FEET – requires underfloor baggage compartment with a minimum of 12-cubic feet.
CSU2- COMPARTMENT-STORAGE-UNDERFLOOR-MINIMUM 16 CUBIC FEET – requires underfloor baggage compartment with a minimum of 16-cubic feet.
CSU3- COMPARTMENT-STORAGE-UNDERFLOOR-MINIMUM 20 CUBIC FEET – requires underfloor baggage compartment with a minimum of 20-cubic feet.
CSU5- COMPARTMENT-STORAGE-UNDERFLOOR-MINIMUM 28 CUBIC FEET – requires underfloor baggage compartment with a minimum of 28-cubic feet.
CSU6- COMPARTMENT-STORAGE-UNDERFLOOR-MINIMUM 32 CUBIC FEET – requires underfloor baggage compartment with a minimum of 32-cubic feet
CSU7- COMPARTMENT-STORAGE-UNDERFLOOR-MINIMUM 36 CUBIC FEET – requires underfloor baggage compartment with a minimum of 36-cubic feet.
CSU8- COMPARTMENT-STORAGE-UNDERFLOOR-MINIMUM 40 CUBIC FEET – requires underfloor baggage compartment with a minimum of 40-cubic feet.
CSU9- COMPARTMENT-STORAGE-UNDERFLOOR-MINIMUM 44 CUBIC FEET – requires underfloor baggage compartment with a minimum of 44-cubic feet.
DCT- DELETE CONSPICUITY TAPE ON ADULT BUS – requires the standard equipment white conspicuity tape to be removed from bus leaving only reflectors required to meet FMVSS requirements.
MCF- MIRROR-CROSSVIEW SYSTEM-FRONT – school bus configuration front mounted crossview mirror system shall be provided and comply with FMVSS.
RM6- MIRRORS-EXTERIOR REARVIEW HEATED REMOTE - Motorized remote controlled and heated, flat and convex surfaces with controls located in driver’s area for both flat and convex mirrors. Heat and position control switch(s) shall be “Marked to Indicate Function” and located in the driver’s area. Heating function shall be automatically deactivated when the ignition switch is turned to the “OFF” position. A Pictogram can be used to identify mirror switches and functions.
3.25.12 Exterior Paint
PCC- PAINT-CUSTOM COLOR- requires any single stage solid color offered by the Contractor in lieu of standard color bright white. A DuPont or other brand product code must be provided to the Contractor at the time of order when requesting this option.
This option covers the vehicle except for the roof, which shall remain white.
3.25.13 Doors and Windows
BVTS - BOTTOM VENT TRANSIT SLIDER – requires all passenger window slider vents to be oriented in the bottom 1/3 of the window pane. The window glazing shall be tinted and tempered safety glass.
ESH- ENTRY STEP-HEATED – requires a driver controlled heated entry step. Step can be heated by means of a thermal balance electric grid embedded in the non-skid step face or heated by engine coolant circulated under the stepwell housing. Electric grid operation shall be controlled by a manual switch marked and located in the driver’s area. Coolant heated step shall be controlled by means of a ¼ ball valve located to prevent accidental damage and marked to locate.
PDST- PASSENGER DOOR- SEDAN TYPE - requires a single panel sedan/plug door, fully gasketed for maximum air and water seal. A VAPOR or equivalent operating mechanism must be used to provide open and closing function.
PWS- PASSENGER WINDOW SHADES – requires sun screening material mounted on a roller above the passenger windows in the control of the passenger to minimize the entry of light from the outside. The shade can be per passenger window or two windows and must have a means to prevent swing regardless of height chosen by the passenger. This option must be priced to include all passenger side windows.
RLD- REAR LOADING DOOR – requires a door located in the rear wall of the passenger compartment leading to the outside of the bus measuring not less than 30-inches wide and 55-inches tall. A step bumper painted to match bus body color or painted black shall be furnished to accommodate entry and exit. Two windows shall be furnished in the door with one in the upper half and a second in the lower. Both windows shall be tempered with the lower window coated with a layer of Huper Optik, VehicleGard or equal film.
This door is considered an emergency exit and must be marked accordingly with signage and red LED light mounted above the light in the interior.
WPFT- WINDOW-PASSENGER-FIXED TOURING - requires manufacturer’s largest available fixed touring window in place of standard window. The window glass shall be tinted and tempered or tinted and laminated safety glass.
WPTS- WINDOW-PASSENGER-TRANSIT SLIDER – requires manufacturer’s largest available transit slider windows to replace the standard equipment windows. The window glass shall be tinted and tempered or tinted and laminated safety glass.
WPT- WHITE ROOF- requires a white painted roof as typically furnished by the bus manufacturer. Check with local/state requirements.
3.25.14 Signage
BSI- SIGN- DESTINATION- ROLLER FRONT - requires the largest available display area, forward-facing, glass-faced, illuminated, internal to body, sign compartment and full width roller curtain display with white background sign material printed with customer designated information. Option BSI shall not be available when options WORQ or WORS are selected unless Option SDRS is also selected to complete ADA required signage.
BSIE- SIGN-DESTINATION-ELECTRONIC-FRONT - requires largest available, display area, forward-facing, glass-faced, internal to body, sign compartment with LED display characters 4 inches in height or taller. All programming software and patch cabling shall be included with this package. If a programming tool other than a laptop computer is required, it shall be furnished with this package. Option BSIE shall not be available when options WORQ or WORS are selected unless Option SDES is also selected to complete ADA required signage.
SDES- SIGN DESTINATION-ELECTRONIC-SIDE - requires largest available, display area, curbside-facing, glass-faced, internal to body, sign compartment with LED display characters 2-inches in height or taller. All programming software and patch cabling shall be included with this package. If a programming tool other than a laptop computer is required, it shall be furnished with this package. Front and side message controls shall be integrated into one controller when Option BSIE is requested.
SDRS- SIGN- DESTINATION- ROLLER SIDE - requires largest available, display area, curbside-facing, glass-faced, internal to body, sign compartment and full width roller curtain display with white background sign material printed with customer designated information.
3.25.15 Lights and Lighting
BRL- INDIVIDUALLY CONTROLLED READING LIGHTS - individually controlled reading lights, one per seating position shall be furnished. Lights can be mounted in pairs but must be fully adjustable to meet individual focus requirements.
ELDI- EXTERIOR LIGHTING DOWNGRADE TO INCANDESCENT – requires removing all exterior LED lamps and replacing them with incandescent where practical and if typically available from the bus manufacturer.
FLP-TRANSIT STYLE INTERIOR FLOURESCENT LIGHTING PKG-requires minimum one row of fluorescent light fixtures installed center of aisle or integrated into overhead parcel racks is requested by option. The fixtures shall extend as far to the rear of the bus and as far forward as possible in a continuous assembly of T-12 bulbs. Lens material shall be clear polycarbonate. Lens shall be designed to effectively "mask" the fluorescent tube. Lens material shall not drip flaming onto seats if burned. Lens shall be sealed to inhibit incursion of dust and insects yet are easily removable for service. If threaded fasteners are used they must be held captive in the lens. Individual ballast shall be provided for each light fixture. Ballast shall have a fireproof housing, minimum operating frequency of 18,000 Hz, reverse polarity protection, integrated circuit breaker/automatic thermal protection, and rebuildable. If the driver’s area ceiling angles down making installation in that area impractical, standard equipment doom lights may be used to provide fill lighting. Additional overhead lighting shall be provided using the manufacturer’s standard interior lighting and be capable of meeting ADA illumination values without the use of the fluorescent fixtures. The fluorescent light fixtures shall be powered by an independent circuit and controlled by a manual switch located in the driver’s area. No time limit shall apply to the on-time of these fixtures with the ignition in the Run or Aux position. A minimum of one dome light over the driver area controlled independently of other interior lighting with a separate switch. Door-open activated stepwell illumination LED lamp(s). Interior illumination shall meet or exceed requirements of ADA 1192.31. The number of lamps used and the combination of are at the discretion of the bus manufacturer.
LED- LIGHTS, LIGHT EMITTING DIODE (LED) - when specified, all exterior lights will be LED in lieu of incandescent unless required photometric values can not be achieved in specific locations. Local and State requirements will take precedence.
3.25.16 Electronics/Audio Visual
PASP-PUBLIC ADDRESS SYSTEM- requires a public address system integrated into the radio system with a corded microphone. When any wheelchair transport option is selected, this option must be shown as required for all 200 series buses.
VCB1- VIDEO CAMERA-BACKUP-DASH MOUNTED COLOR MONITOR – requires a backup camera system that includes a color monitor mounted in the driver’s area with viewable screen not less than 6.8 inches and weatherproof reverse image color camera center mounted at highest practical location in rear of bus. Dash mounted monitor shall be in driver’s normal windshield viewing angle as close as practical to the driver for easy viewing but not obstructing normal driving view when not in use.
VCS2- VIDEO CAMERA-SECURITY PACKAGE-TWO CAMERA AND STORAGE DRIVE –Requires minimum of two interior mounted miniature color video cameras with one located to provide a forward facing driver’s view of the area in front of the bus and the second located on the forward bulkhead providing an image of the total passenger compartment. Image storage shall be on a rugged-duty hard drive recording at a resolution capable of not less than 720 x 486.
VV1- VIDEO VIEWING-DVD/VCR W/ 1-13” TFT/LCD MONITORS CENTER MOUNTED - requires one, manual flip down 13-inch or larger TFT/LCD monitors mounted as far forward as practical to allow all passengers to view. The screen can also be fixed mounted in a forward bulkhead or divider if practical so long as it is integrated into the part that supports it. A DVD player or combination AM/FM/CD/DVD shall be located for operation by the driver. Option LRI must be selected.
VV2- VIDEO VIEWING-DVD/VCR W/ 2-13” TFT/LCD MONITORS CENTER MOUNTED - requires two, manual flip down 13-inch or larger TFT/LCD monitors, one mounted as far forward as practical to allow for first row passengers to view and the second mounted to allow rear half of passengers to view. The screen can also be fixed mounted in a forward bulkhead or divider if practical so long as it is integrated into the part that supports it and the distance from the furthest passenger does not exceed 15-feet. A DVD player or combination AM/FM/CD/DVD shall be located for operation by the driver. Option LRI must be selected.
VV3- VIDEO VIEWING-DVD/VCR W/ 3-13” TFT/LCD MONITORS CENTER MOUNTED - requires three, manual flip down 13-inch or larger TFT/LCD monitors, one center mounted as far forward as practical to allow for first row passengers to view with the remaining two proportionally spaced, center mounted to provide comfortable viewing at all passenger positions. A DVD player or combination AM/FM/CD/DVD shall be located for operation by the driver. Option LRI must be selected.
VV4- VIDEO VIEWING-DVD/VCR W/ 4-8” TFT/LCD MONITORS ROW MOUNTED – requires four, fixed mount, 8-inch or larger TFT/LCD monitors, two per side with one mounted as far forward as practical to allow for first row passengers to view with the remaining proportionally spaced, center mounted between seated pair. A DVD player or combination AM/FM/CD/DVD shall be located for operation by the driver. Option LRI must be selected.
VV6- VIDEO VIEWING-DVD/VCR W/ 6-8” TFT/LCD MONITORS ROW MOUNTED – requires six, fixed mount, 8-inch or larger TFT/LCD monitors, three per side with one mounted as far forward as practical to allow for first row passengers to view with the remaining proportionally spaced, center mounted between seated pair. A DVD player or combination AM/FM/CD/DVD shall be located for operation by the driver. Option LRI must be selected.
VV8- VIDEO VIEWING-DVD/VCR W/ 6-8” TFT/LCD MONITORS ROW MOUNTED – require eight, fixed mount, 8-inch or larger TFT/LCD monitors, four per side with one mounted as far forward as practical to allow for first row passengers to view with the remaining proportionally spaced, center mounted between seated pair. A DVD player or combination AM/FM/CD/DVD shall be located for operation by the driver. Option LRI must be selected.
3.25.17 Interior
BBGR- INTERIOR REAR BAGGAGE COMPARTMENT – requires a rear luggage compartment measuring full nominal interior width and height of bus and not less than 28-inches deep shall be furnished. Interior height of compartment can be reduced to accommodate air-conditioning evaporator. Entrance doors to compartment shall open to the rear of the bus and measure not less than
30-inches wide and 55-inches tall. A step bumper painted to match bus body color or painted black shall be furnished to accommodate entry to luggage compartment. This option will reduce passenger-seating capacity.
BFST- BARRIER-FULL HEIGHT-TRANSLUCENT – requires the standard driver’s area barrier to be substituted by full height Lexan, smoked charcoal color; translucent, driver’s barrier. The barrier shall minimize glare and reflections in the windshield directly in front of the barrier from interior lighting during night operation. The barrier shall extend from the floor to the ceiling and shall fit the bus side windows, wall, and ceiling panels to prevent passengers from reaching the operator or the operator’s personal effects. The barrier shall comply with all ADA requirements.
BIF-FABRIC SURFACE INTERIOR SIDE PANELS-requires ceiling panels and walls to be covered with medium grey padded, woven, stain resistant, industrial cloth fabric or carpet.
CPFS-CEILING PADDED FABRIC SURFACE-requires ceiling to be covered with medium gray padded, woven, stain resistant, industrial cloth fabric or carpet.
GR- STANDEE GRAB RAILS – requires, except forward of the standee line and to a point within 18 inches of the face of the rear seat, two continuous, full grip, overhead assist. These assists shall be convenient to standees and shall be located off center of the aisle. The assist shall be no less than 70 inches above the floor. Overhead assists shall simultaneously support 150 pounds on any 12-inch length. No more than 5 percent of the full grip feature shall be lost due to assist supports. Standee line shall be marked in accordance with Federal Motor Carrier Safety Regulation 393.90. Additional passenger load equaling one 215 lb person per 2.5 square feet of aisle space shall be added to the passenger load calculation. When calculated standee capacity ends with a fraction the capacity shall be rounded down to nearest whole number. Passenger loading stickers in paragraph 3.1.21 shall be amended to include the total passenger capacity including standees and delete the verbiage “No Standees”. Included in this option shall be all body, chassis, suspension, transmission, driveline, tire, etc requirements to safely handle the occupant capacity and meet GVWR and GAWR requirements. This option is not available with option LRI (INTERIOR OVERHEAD PARCEL RACKS.)
IVR- INTERIOR WALLS AND CEILING - VANDAL RESISTANT – requires the interior walls and ceiling surface material to be white melamine or similar material ILO the standard.
LRI- INTERIOR OVERHEAD PARCEL RACKS – requires right and left side, full length open-faced, overhead parcel racks.
Retaining lip or bungee cord luggage retaining devices shall be intrinsic to the design features. Minimum vertical clear opening shall be 8-inches with interior measurement vertical measurement of 10-inches. Air volume shall not be restricted or diverted when parcel rack contains passenger carryon items. This option is not available with option GR (STANDEE GRAB RAILS.)
NR-NOISE REDUCTION PACKAGE- requires all noise reduction methods available from body and chassis manufacturer to be added to the standard package. Examples of noise reduction methods that shall be included are complete lining of stepwell treads, and sides with multi layer matting, urethane foam underbody insulation, application of insulation and acoustical coating, noised reducing mufflers, underbody and engine compartment shielding.
RL36- RACK LUGGAGE-MINIMUM DIMENSION 22in X 36in 2-TIER – requires a tubular two tier luggage rack with shelving area measuring not less than 22-inches deep by 36-inches wide and shall be installed immediately behind the driver’s area.
The rack shall be installed by securely mounting to floor stringer or tapping plates. This option will reduce seating capacity.
RL60- RACK LUGGAGE-MINIMUM DIMENSION 22in X 60in 2-TIER – requires a tubular two tier luggage rack with shelving area measuring not less than 22-inches deep by 60-inches wide and shall be installed immediately behind the driver’s area.
The rack shall be installed by securely mounting to floor stringer or tapping plates. This option will reduce seating capacity.
SMW- STORAGE AREA MOVABLE WALL – requires a tract mounted three piece movable wall to be used in conjunction with Option BBGR. The wall sectional shall be secured to the walls and ceiling with heavy-duty U-track with quick release locking levers allowing the wall to be moved with the use of tools or complete disassembly.
3.25.18 Floor
CM-CARPETED FLOOR COVERING - requires closed loop, industrial grade, stain resistant, treated carpeting in lieu of standard flooring. Standard color is medium grey. Aisle shall remain standard material.
FL-FLAT FL BUS W/NO WHEEL HOUSE INTRUSION IN PASS AREA – requires no rear wheelhouse intrusion in passenger area. Minimum interior height shall not be reduced. Low profile tires can be used to lower overall height of bus.
WWF-WATER RESISTANT WOOD FLOORING-requires water resistant marine grade plywood flooring a minimum of 5/8” nominal thickness.
3.25.19 Heating Ventilation Air Cond
ACRE- A/C-ELECTRIC - ENGINE & SHORE POWERED-ROOF MOUNTED – requires an electrically driven all in one roof mounted evaporator, condenser, and sealed compressor unit, Carrier AVANTAC or equal, which equals or exceeds the stated capacity of the standard equipment system. Multiple RV type pods systems are not acceptable for this option. The electric power source when the bus is in motion can be furnished by a single phase 220 VAC or 3 phase 480 VAC, primary mover engine, PTO, or hydraulically driven generator. A NEC approved commercially available shore power plug outlet with moisture proof cover shall be located to provide easy connection when the bus is stationary. Furnishing a shore power connection cable is not required.
BOI-BUS OPTIONAL INSULATION PACKAGE-requires all bus and chassis manufacturer’s optional insulation packages including but not limited to all available firewall insulation, minimum R-value of 5 and shall fill all cavity areas and voids in outer and inner walls, outer, and inner roof , and roof bow hat sections.
CARM – CONDENSER AIR CONDITIONING ROOF MOUNTED – requires the relocation of the air conditioning condenser to the roof. The condenser and total system capacity shall remain the same or greater when this option is required.
CTD – COMPRESSOR AIR CONDITIONING UPGRADE TO TRANSIT TYPE – requires replacement of the standard equipment dual swash plate compressors by a single or multiple compressors from the list below. The BTUH capacity shall equal or exceed the dual swash plate compressors replaced.
The following compressors are acceptable for this requirement dependant on application:
Bitzer Models: F400 and 4NFC
Carrier Model: 05K and 05G
Thermo King Model: X430
Bock Model: FK40 and FK50
Valeo: TM65 and TM55
DA- DELETE AIR CONDITIONING – requires the complete deletion of the standard equipment air conditioning and requires two driver’s fans be installed on opposite sides of the bus for driver comfort. This option also deletes the requirement for a white roof unless option WPT is also selected on 200 series buses.
3.25.20 Seating
EFSF- ECO FRIENDLY RECYCLED YARN SEAT FABRIC – seat covers furnished must be made from 100% recycled yarn and a minimum of 80% post consumer plastic water bottles. Material must meet FMVSS safety standards.
EFSC- ECO FRIENDLY SEAT CUSHIONS – seat cushions and backs furnished must be made of at least 20% agricultural based oil and meet ASTM 3574.
GRS- SEAT-PASSENGER-GRAB HANDLE – requires molded high-density foam with internal structural support or molded thermoplastic grab handle, mounted to the aisle side upper corner on high back seats and top mounted on Mid-High seats. Option price shall reflect the upgrade of all passenger seats.
PSDB- PASSENGER SEATING DOWNGRADE TO BENCH – requires the downgrade of the standard highback, certified, school activity seat to a 36-inch school bus bench.
1. The seat cover shall be a medium grey color.
2. Material class rating must be ASTM D-3690-Class A or better.
3. UV Stabilized Pigments must be 500 hour minimum.
RSCP- PREMIUM HIGHBACK RECLINING SEAT- 19-INCH WIDE – requires American Seating Model 2005 or Freedman Ritz recliner with seat bottom width of 19-inches and upholstered flip-up arms on wall and aisle sides with standard material cover or one of the seat material options described elsewhere this specification.. This option shall be priced to upgrade all passenger seats from standard Mid-high.
RSCU- SEAT-HIGH BACK-RECLINING-CLOTH COVERED W/ARMREST - requires Freedman Featherweight Recliner, American Horizon High Back Recliner, or CE White LER-35-HB with standard material cover or one of the seat material options described elsewhere this specification.
1. Minimum seat bottom cushion width 17½ -inches.
2. Aisle side molded rubber/plastic movable arm rests.
3. This option shall be priced to include the upgrade of all passenger seats.
S3BA- SEAT-PASS-3 PNT BELT SYSTEM HIGH BACK SCHOOL CERTIF - requires American Seating SafeGuard Premier, Freedman 3 Point Family seat or CE White FoFinta in lieu of standard fixed back FMVSS 222 certified bucket seat. Seat cover material shall be Predictions Grey vinyl. This option upgrades all passenger seats.
S3BH- SEAT-PASSENGER-3 POINT BELT SYSTEM HIGH BACK - requires Freedman 3 Point Seat High back in lieu of standard fixed back Mid High.
a. Seats shall be equipped with aisle side molded rubber/plastic movable armrest and Level 3 woven cloth fabric.
b. This option upgrades all passenger seats.
S3BM- SEAT-PASSENGER-3 POINT BELT SYSTEM MID HIGH - requires Freedman 3 Point Seat Mid-Hi in lieu of standard fixed back Mid High.
a. Seats shall be equipped with aisle side molded rubber/plastic movable arm rest and Level 3 woven cloth fabric.
b. This option shall be priced to include the upgrade of all passenger seats.
SAS- SEAT-AISLE SLIDER- requires a mechanical locking slide mechanism to aisle side seats that allows the aisle seat to be moved a minimum of 2-inches into the aisle for added shoulder and hip room. This Option is available to upgrade SHB or standard Mid High seats. Option shall be priced to include the upgrade of all aisle side passenger seats.
SB3B – SEAT BENCH 3-POINT BELTS – requires the substitution of the standard 39-inch bench with a convertible 3 and 2, 3-point seat belt system bench. This option shall only be available in those States that do not specifically prohibit them. This option shall not be used in those States that require 3-point belt system benches.
SCO1- CO-PILOT SEAT- MECHANICAL SUSPENSION – requires the addition of a second driver type highback seat in the cab located in the right hand position. The seat shall be reclining type with minimum left side arm rest and covered with the same cloth as the driver seat.
SCO- CO-PILOT SEAT- AIR SUSPENSION - requires the addition of a second driver type highback seat in the cab located in the right hand position. The seat shall be reclining type with adjustable lumbar features. The seat shall have a minimum of left side arm rest and covered with the same cloth as the driver seat.
SCS4- SEAT-CLOTH-STAIN/FLUID RESISTANT-LEVEL 4 FABRIC – requires REPEL fabric, color 187 Icon Grey. This option shall be priced to include the upgrade of all passenger seats.
SCS6- SEAT-CLOTH-STAIN/FLUID RESISTANT-LEVEL 6 FABRIC – requires LaFrance Industries Synergy-EH fabric #342- 036D-84-E545, color Steel (Grey). This option shall be priced to include the upgrade of all passenger seats.
SCS7- SEAT FABRIC-STAIN/FLUID RESISTANT-CMI ILLUSION BLACK – requires seat fabric upgrade from standard level 3 Sherpa to CMI Illusion fabric, color black or equal simulated leather material. This option shall be priced to include the upgrade of all passenger seats.
SCU1- OLEFIN SEAT FABRIC - CROSS WOVEN - GREY – requires woven Olefin grey color cloth. This option shall be priced to include all passenger seats.
SCU3- SEAT-CLOTH UPHOLSTERY-LEVEL 3 FABRIC – requires Sherpa Gray Heather #965 face fabric. This option shall be priced to include the upgrade of all passenger seats.
SCU4- SEAT FABRIC- CMI PLUSH FLAGS GREY #158 CLOTH – requires CMI Plush #158 Flags grey fabric. This option shall be priced to include the upgrade of all passenger seats from standard level 3 Sherpa.
SCU5- SEAT FABRIC- LAFRANCE MILLS TOWER 3000 GREEN #539 CLOTH – requires LaFrance Mills Tower 3000 green #539 cloth. This option shall be priced to include the upgrade of all passenger seats from standard level 3 Sherpa.
SCU6- SEAT FABRIC- LAFRANCE MILLS MOSIAC #551 CLOTH – requires LaFrance Mills Mosiac #551 cloth. This option shall be priced to include the upgrade of all passenger seats from standard level 3 Sherpa.
SFD- SEAT-FOLDING-DOUBLE – requires one double Mid-High folding seat, with a seat bottom that folds/flips up and locks to a vertical position such as the Freedman FW Flip and American Seating Horizon Flip Up. This option is intended to be used in conjunction with Options WORQ and WORX but not required.
SFD2- SEAT-FOLDING-FLIP-DOUBLE – requires one double Freedman FSC Foldaway or American Seating Horizon Cantilevered Folding, Mid-High folding flip seat that fold down and flips up to store against the bus wall. This option is intended to be used in conjunction with Options WORQ and WORS but not required.
SHB- SEAT-PASSENGER-HIGHBACK - requires Freedman Feather Weight High Back with fixed back in lieu of standard fixed back Mid High.
1. Seats shall be equipped with aisle and center movable arm rests with Sherpa Gray Heather #965 face fabric.
SICA- SEAT-CHILD SEAT-INTEGRATED-ADULT BUS - requires the substitution of one pair of Midhigh seats with an Integrated Child Securement (ICS) seat. Seat and installation shall comply with FMVSS No. 210 and 213. The number of ICS equipped seats required must be specified at the time of order.
SICS- SEAT-CHILD SEAT-INTEGRATED-SCHOOL BUS - requires the substitution the standard bench with an IMMI SafeGuard or CE White CR series bench with two Integrated Child Securement (ICS) seats. Seat and installation shall comply with FMVSS No. 210 and 213. The number of ICS equipped benches required must be specified at the time of order.
SID- IMPROVED DRIVER SEAT – requires replacement of the standard equipment seat with one having the following features:
1. Right side adjustable arm rest.
2. Adjustable headrest.
3. Minimum of two way adjustable lumbar support.
SID2- IMPROVED AIR RIDE DRIVER’S SEAT – driver’s seat shall be air ride with adjustable lumbar, cushion, backrest, and height adjustment. Driver’s seat shall be equipped with 3-point safety belt system and right movable armrest.
STLB- SEAT TRANSIT- LOW BACK - requires American Seating Metropolitan or Freedman Citiseat with padded Synergy fabric upholstered inserts.
SPB- SEATING PERIMETER - requires all seating to be arranged in perimeter orientation. Seats shall be positioned around the entire perimeter of the bus interior with no gaps between seats other than for door openings. This option will reduce seating capacity.
TMS-SEATS-TRACK MOUNTED - requires floor mounted seat tracks for all forward facing passenger seating to allow for indexed seating positioning or removal. Removable track filler strips shall be installed between seat rows to prevent debris from entering track and to protect passengers from sharp edges. Installation shall maintain all FMVSS certifications.
VCPS- VINYL COVER PASSENGER SEATS – Nanocide antimicrobial impregnated vinyl substituted for standard cloth. This option shall be priced to include the changing seating surface of all passenger seats.
3.25.21 Wheelchair Transport Equipment
3WSK- TRI-WHEEL SCOOTER SECUREMENT KIT- USE WITH LIFT PACKAGE – requires Q’Straint scooter mounting kit Q5-7583-A to be furnished individually. This option will secure one scooter per unit requested.
BWP- ADDITIONAL WHEELCHAIR POSITIONS - requires the addition of one wheelchair position to be added to options WORS, WORQ, or HPBS. This option increases the number of wheelchair positions by one. Multiples of this option can be requested. All positions shall comply with FMVSS 571.210, 222, 403, 404.
HLF- WHEELCHAIR LIFT- LOCATED TO FRONT BEHIND ENTRY DOOR – requires locating the wheelchair and door to front right side of the bus just behind the passenger entry door.
HPA- 1,000 LB CAP WHEELCHAIR LIFT UPGRADE – requires upgrading the standard 800 lb capacity lift provided by options WCL1 to the Maxon WL7 with 1000lb certified capacity or WCL3 to the Braun Century2 NCL9 1000 lb certified capacity. This option shall include all improvements in the floor structure and chassis mounting points to accommodate the greater loads experienced. This option requires option WCL1 or WCL3.
HPBS- HANDICAP PACKAGE SCHOOL-ONE WHEELCHAIR POSITION - requires the modification of the bus to comply with FMVSS 571.403 and 404 as applicable to school bus use. Lift shall be electric with power up and fold-up platform and rated for public use. This option provides a securement location for one wheelchair. The securement hardware shall be the QRT Max system.
This option reduces overall seating capacity.
SCFS- WHEELCHAIR, FLOOR-POCKET ANCHORS ILO STD TRACKS - requires the Q’Straint Slide n’ Click or Sure-Lok Solo Anchor floor mounting system per wheelchair position and modification to the belt system floor point to match the pocket mount.
TDSS- WHEELCHAIR TIE-DOWN STORAGE SYSTEM- UNDER SEAT TYPE – requires the addition of a Tie-Down Storage System to be added to the underside of seating option SFD2. The option shall be priced to include one retainer hardware set per convertible seat for either “L” track or Slide n’ Click mounting systems. It is recommended that the number of quantity ordered equal the number of wheel chair positions required.
WCL1 – MAXON WHEELCHAIR LIFT PACKAGE - requires the modification of the bus to comply with the Americans with Disabilities Act (ADA) Accessibility Specifications for Transportation Vehicles.
1. Chair lift shall be rated for public use.
2. All safety equipment, markings, interior signage, and labels required in accordance with the Americans with Disabilities Act Accessibility Guidelines for Transportation Vehicles in affect at the time the bus is manufactured. No external signs or stop buzzer shall be furnished.
3. Maxon WL7 electric lift package with Smart lift controls. The lift platform must measure a minimum clear width of 34-inches and minimum clear platform length of 52-inches.
4. Access door positioned on curbside as far rearward as practical.
5. When Option LRI is specified with this Option an additional evaporator shall be installed in the wheelchair lift area to compensate for the additional heat load created by the wheelchair door opening or when ducted air is lost due to the removal of a portion of the air passage.
6. This Option reduces overall seating capacity.
WCL2 – RICON WHEELCHAIR LIFT PACKAGE - requires the modification of the bus to comply with the Americans with Disabilities Act (ADA) Accessibility Specifications for Transportation Vehicles.
1. Chair lift shall be rated for public use.
2. All safety equipment, markings, interior signage, and labels required in accordance with the Americans with Disabilities Act Accessibility Guidelines for Transportation Vehicles in affect at the time the bus is manufactured. No external signs or stop buzzer shall be furnished.
3. Ricon S2010 or S5010 applicable to application with platform minimum clear width of 34-inches and minimum clear platform length of 52-inches.
4. Access door positioned on curbside as far rearward as practical.
5. When Option LRI is specified with this Option an additional evaporator shall be installed in the wheelchair lift area to compensate for the additional heat load created by the wheelchair door opening or when ducted air is lost due to the removal of a portion of the air passage.
6. This Option reduces overall seating capacity.
WCL3 – BRAUN WHEELCHAIR LIFT PACKAGE - requires the modification of the bus to comply with the Americans with Disabilities Act (ADA) Accessibility Specifications for Transportation Vehicles.
1. Chair lift shall be rated for public use.
2. All safety equipment, markings, interior signage, and labels required in accordance with the Americans with Disabilities Act Accessibility Guidelines for Transportation Vehicles in affect at the time the bus is manufactured. No external signs or stop buzzer shall be furnished.
3. Braun Mobility lift with platform minimum clear width of 34-inches and minimum clear…
This is the start of the file's text. The full file is on GovTribe.
File details come from the government source that posted it. Updated .