Attachment C-2012 Fed Std 794AE 7.1.11.pdf

Federal Standard Jul 1, 2011 PDF 503 KB Posted

Attached to
Electric medium duty trucks and item 888E representing commercially made motor vehicles incorporating emerging technology for which there is an existing Federal Standard 794, 833, 807 vehicle category
Solicitation number
QMAE-CR-110003-N
Issued by

About this file

C-Federal Standards (Specifications)

View the file

Other versions and copies of FED-STD-794

Who attaches FED-STD-794

Other files

File Type Posted
Attachment_J_-_Inspection_Points_Template.xls XLS spreadsheet
Amendment 002 QMAE-CR-110003-N Page 1.pdf PDF
QMAE-CR-110003-N Amendment 002 Pages 2-4.pdf PDF
Attachment C-DRAFT Fed Std 833F Item 398 Heavy Duty Over the Road Touring Coach 06.24.2011.pdf PDF
QMAE-CR-110003-N Amendment 001 page 1.pdf PDF
Attachment C-DRAFT Fed Std 833F Item 202C Type A School Bus Basic 06.24.2011.pdf PDF
Attachment C-DRAFT Fed Std 833F Items 301C-304C Type A School Bus 06.24.2011.pdf PDF
Attachment c-Item 888E.pdf PDF
Attachment C-DRAFT Fed Std 833F Items 259W-263W Medium Duty Shuttle Basic 06.24.2011.pdf PDF
Attachment C-DRAFT Fed Std 833F Items 341N-347L Light Duty Shuttle Bus 06.24.2011.pdf PDF
Attachment_A_-_Proposal_Checklist.pdf PDF
Attachment C-DRAFT 2012 Fed Std 833F Bus Options Appendix A Specifications 06.24.2011.pdf PDF
Attachment C-DRAFT Fed Std 833F Item 398D Double Deck Touring Bus 06.24.2011.pdf PDF
Amendment 001 QMAE-CR-110003-N Pages 2-13.pdf PDF
Attachment C-DRAFT Fed Std 833F Items 236A-238A Type D Rear Engine Work Bus Basic 06.24.2011.pdf PDF
Attachment C-DRAFT Fed Std 833F Items 320A-332A Types C and D Front Engine Work Bus 06.24.2011.pdf PDF
Attachment C-DRAFT Fed Std 833F Items 220C-232C Types C and D Front Engine School Bus Basic 06.24.2011.pdf PDF
Attachment C-DRAFT Fed Std 833F Item 390 Heavy Duty Intercity Commuter Coach 06.24.2011.pdf PDF
Attachment C-DRAFT Fed Std 833F Items 336C-338C Type D Rear Engine School Bus 06.24.2011.pdf PDF
Attachment C-DRAFT Fed Std 833F Items 336A-338A Type D Rear Engine Work Bus 06.24.2011.pdf PDF
Attachment C-DRAFT Fed Std 833F Items 236C-238C Type D Rear Engine School Bus Basic 06.24.2011.pdf PDF
Attachment C-DRAFT Fed Std 833F Items 359W-363W Medium Duty Shuttle Bus 06.24.2011.pdf PDF
Attachment C-DRAFT Fed Std 833F Items 220A-232A Types C and D Front Engine Work Bus Basic 06.24.2011.pdf PDF
Attachment C-DRAFT Fed Std 833F Items 241N-247 Light Duty Shuttle Basic 06.24.2011.pdf PDF
Attachment C-DRAFT Fed Std 833F Items 320C-332C Types C and D Front Engine School Bus 06.24.2011.pdf PDF
Attachment_D_-_Weekly_Vendor_Status_Submission_Requirements.pdf PDF
Attachment C- 531E.pdf PDF
Attachment C-561E.pdf PDF
QMAE-CR-110003-N.pdf PDF
Attachment_D_-_Weekly_Status_Reports_EXAMPLE.xlsx XLSX spreadsheet
Attachment G-GSA 1678.pdf PDF
Attachment C-Item_888E.pdf PDF
Attachment_B_-_Technical_Exceptions_Worksheet.xlsx XLSX spreadsheet
Attachment_F_-_AutoChoice_Online_Ordering_Instructions.pdf PDF
Attachment_E_-_Small_Business_Subcontracting_Plan.pdf PDF
Attachment_I_-_Dealers_Layout.xlsx XLSX spreadsheet
Attachment H AUTOBID Vendor Instructions.pdf PDF
Attachment C-2012 Fed Std 807T 7.1.11.pdf PDF
Attachment_A_-_Proposal_Checklist.pdf PDF
Attachment C-571E.pdf PDF
2012 Fed Std 807T 7.1.11.pdf PDF
Item_888E.pdf PDF
AutoBid_Vendor_Instructions.pptx PPTX presentation
571E federal standard.pdf PDF
531E federal standard.pdf PDF
2012 Fed Std 794AE 7.1.11.pdf PDF
561E Federal Standard.pdf PDF
Show all 47

On GovTribe

Work with this file

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file

Text version

Federal Standard 794AE Page - 1 - of 78

Fed Std 794AE July 1, 2011

Superseding Fed Std 794AD June 1, 2010

FEDERAL STANDARD

TRUCKS: MEDIUM COMMERCIAL, 4X2 and 4X4

9,500 TO 16,000 KG (21,000 TO 35,000 LBS) GVWR

Federal Standard 794AE Page - 2 - of 78

TRUCKS AND TRUCK TRACTORS: Medium Commercial 4X2 & 4X4, 9,500 TO 16,000 KG (21,000 TO 35,000 LBS) GVWR

Federal Standards Number 794AE July 1, 2011

Superseding Federal Standard Number 794AD, June 1, 2010

1. SCOPE AND CLASSIFICATION

1.1 SCOPE.

This document covers new commercially produced, four wheeled, two and four wheel drive (4x2 & 4x4) medium trucks. It is intended to simplify competitive procurement of commercial vehicles, and achieve a practical degree of standardization within the federal fleet.

This Federal Standard does not include all the varieties of the commodity indicated by the title but is intended to cover only those vehicles generally acquired by the Government. This standard highlights, in concise form, types of trucks with standardized components and equipment. A selection of coded optional additional systems and equipment is included for agencies divergent geographic and operational related needs. The requirements of the standard may be tailored to meet unusual operating conditions, to incorporate special purpose equipment, and to provide for exceptions not otherwise covered.

These trucks are warranted by the contractor/supplier upon delivery as specified in 6.3 of this standard. Vehicle procurement must comply with the Federal Property Management Regulations (FPMR) and the Federal Procurement Regulations (FPR).

The types of vehicles covered by this standard are listed below.

1.2 CLASSIFICATION.

The vehicle(s) are divided into “Types” and “Classes.” The vehicle types are determined by the chassis/body configuration. The “Class” of vehicle(s) shall be determined by the minimum gross vehicle weight rating (GVWR) as follows:

Figure 1. Types and Classes

TYPES NOMENCLATURE CLASS

I Chassis, truck, with cab (see 3.5.1) C D F G

II Truck, tractor, with cab (see 3.5.2) E F G

III Truck, stake, with cab (see 3.5.3) C D F

IV Truck, dump, with cab (see 3.5.4) C D F G

V Reserved Reserved

VI Reserved Reserved

VII Truck, van, with cab (see 3.5.7) C D F

VIII Truck, refrigerator van, with cab (see 3.5.8) C D F

CLASS C D E F G

(KG) 9,500 11,500 12,700 14,500 15,900

(LBS) 21,000 25,500 28,000 32,000 35,000

Federal Standard 794AE Page 3 of 78

ITEM # TYPE CLASS ITEM # TYPE CLASS

414 ............. I .......... C 434 .............. III ............... C

444 ........... IV ......... C 571 ............. VII .............. D

................... ............ 573 ............. VII .............. F

474 ........... VII ......... C 581 ............. VIII .............. D

484 .......... VIII ........ C 583 ............. VIII .............. F

511 ............. I .......... D 712 ............... I ................ D

513 ............. I .......... F 714 ............... I ................ F

514 ............. I .......... G 732 .............. III ............... D

522 ............ II .......... E 734 .............. III ............... F

523 ............ II .......... F 742 .............. IV ............... D

524 ............ II .......... G 744 .............. IV ............... F

531 ............ III ......... D 745 .............. IV ............... G

533 ............ III ......... F

541 ........... IV ......... D

543 ........... IV ......... F

544 ........... IV ......... G

1.3 STANDARD TRUCK AND ALTERNATE COMPONENTS.

The standard truck shown as a “numbered item” with components listed as “GSA Min Req” in the Autochoice/Autostandards database are minimum requirements and shall be furnished in accordance with the referenced specification. A selection of alternate options and equipment are listed under “Options Description” in each item number at the end of the minimum requirements for each Item Number with “codes” applicable to the specific type/style truck. These shall be furnished when the code(s) are specified.

NOTE: Payload is reduced by the weight of options specified such as lift gates, winch, snowplow, increased body size, and other equipment not included in the minimums for each Standard Item.

2. APPLICABLE DOCUMENTS

2.1 ISSUES OF DOCUMENTS.

The following documents of the issue in effect on date of invitation for bids or request for proposal form a part of this standard to the extent specified herein.

Fed. Std. No. 595B -Colors.

Federal standards and specifications are available from:

GSA Specification Section Suite 8100 470 L’Enfant Plaza, S.W.

Washington, D.C. 20407

Telephone: (202) 619-8925.

Copies of this standard are available on the Internet at www.gsa.gov.

2.1.1 SPECIFICATIONS, STANDARDS, AND HANDBOOKS.

The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents

Federal Standard 794AE Page 4 of 78 are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, in effect on date of solicitation.

COMMERCIAL ITEM DESCRIPTIONS

A-A-55439 Battery, Storage: Vehicular, Ignition, Lighting and Starting.

A-A-50271 Plate, Identification, instruction and marking.

HANDBOOKS

MIL-HDBK–1223 Nontactical Wheeled Vehicles Treatment, Painting, Identification Marking, and Data Plate Standard.

MIL-HDBK–1791 .... Designing for Internal Aerial Delivery in Fixed Wing Aircraft

DH-1-11AFSC Design Handbook.

SPECIFICATIONS

MILITARY

MIL-T-5624 Turbine Fuel, Aviation, Grades JP - 4 and JP-5.

MIL-T-83133 Turbine Fuel, Aviation, Kerosene Type, Grade JP-8.

MIL-PRE-20696 Cloth, Waterproof, Weather Resistant.

STANDARDS

FEDERAL

FED-STD-297 Rustproofing of Commercial (Nontactical) Vehicles.

MILITARY

MIL-STD-209 Lifting and Tiedown Provisions

MS 75020 Connector, Plug, Electrical - 12 Contact, Intervehicular, 28-Volt, Waterproof.

MS 75021 Connector, Receptacle, Electrical - 12 Contact, Intervehicular, 28-Volt, Waterproof.

Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from:

Naval Publications and Forms Center Military Specifications and Standard, Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094

2.1.2 OTHER GOVERNMENT DOCUMENTS, DRAWINGS, AND PUBLICATIONS.

The following other Government document, drawings, and publications form a part of this specification to the extent specified herein. Unless otherwise specified, the issues are those in effect on date of solicitation.

Department of Commerce (DOC)

Voluntary Product Standard PS 1-95 Construction and Industrial Plywood

Application for copies of DOC publications should be addressed to:

Superintendent of Documents

Federal Standard 794AE Page 5 of 78

U.S. Government Printing Office Washington, D.C. 20402-9325.)

DEPARTMENT OF TRANSPORTATION (DOT)

Federal Motor Carrier Safety Regulations.

Federal Motor Vehicle Safety Standards.

Application for copies of DOT publications should reference the Code of Federal Regulations, 49 CFR, and the Federal Register, and should be addressed to:

The Superintendent of Documents U.S. Government Printing Office Washington, DC 20402

ENVIRONMENTAL PROTECTION AGENCY (EPA)

Control of Air Pollution from New Motor Vehicles and New Motor Vehicle Engines.

Noise Emission Standards for Transportation Equipment - Medium and Heavy Trucks.

Application for copies of EPA publications should reference the Code of Federal Regulations, 40 CFR, and the Federal Register and should be addressed to:

Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402

OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION (OSHA)

Subpart N Cranes, Derricks, Hoists, Elevators, and Conveyors.

Application for copies of OSHA publications should reference the Code of Federal Regulations, 29 CFR, and the Federal Register and should be addressed to:

The Superintendent of Documents U.S. Government Printing Office Washington, DC 20402.)

2.2 NON-GOVERNMENT PUBLICATIONS.

The following documents form a part of this document to the extent specified herein.

Unless otherwise specified, the issued of the documents that are DOD adopted are those listed in the issue of the DODISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents in effect on the date of solicitation.

THE EUROPEAN TYRE AND RIM TECHNICAL ORGANIZATION (ETRTO)

Standards Manual.

Application for copies of the ETRTO publication should be addressed to:

European Tyre and Rim Technical Organizations 32, Avenue Brugman 1060 Brussels, Belgium

NATIONAL FIRE PROTECTION ASSOCIATION (NFPA)

NFPA No. 70 National Electric Code.

Application for copies of NFPA publications should be addressed to:

Federal Standard 794AE Page 6 of 78

The National Fire Association Batterymarch Park Quincy, MA 02269

NATIONAL TRUCK EQUIPMENT ASSOCIATION (NTEA)

Conversion Hoist Chart.

Dump Body Hoist Chart.

Application for copies of NTEA publications should be addressed to:

National Truck Equipment Association 38705 Seven Mile Road, Suite 345 Livonia, MI 48152

SAE, INC.

SAE Standards and Recommended Practices

J318 Air Brake Gladhand Service (Control) and Emergency (Supply) Line Couplers -Trucks, Truck-Tractors, and Trailers (DOD adopted).

J350 Spark Arrester Test Procedure for Medium Size Engines (DOD adopted).

J516 Hydraulic Hose Fittings.

J517 Hydraulic Hose.

J537 Storage Batteries.

J551 Performance Levels and Methods Measurement of Electromagnetic Radiation from Vehicles and Devices (30-1000 MHz).

J560 Seven-Conductor Electrical Connector for Truck-Trailer Jumper Cable.

J682 Rear Wheel Splash and Stone Throw Protection (DOD adopted).

J683 Tire Chain Clearance - Trucks, Buses, and Combinations of Vehicles.

J700 Upper Coupler Kingpin - Commercial Trailers and Semi trailers.

J704 Openings for Six- and Eight-Bolt Truck Transmission Mounted Power Take- Offs.

J844 Nonmetallic Air Brake System Tubing (DOD adopted).

J994 Alarm- Backup- Electric.

J1067 Seven-Conductor Jacketed Cable for Truck-Trailer Connections.

J2188 Truck Ability Prediction Procedure (DOD adopted).

(Application for copies of SAE publication should be addressed to SAE, Inc., 400 Commonwealth Drive, Warrendale, PA 15096.)

THE TIRE AND RIM ASSOCIATION, INC.

Year Book.

Application for copies of Tire and Rim Association publication should be addressed to:

Tire and Rim Association, Inc., 175 Montrose West Avenue Copley, OH 44321

Federal Standard 794AE Page 7 of 78

THE MAINTENANCE COUNCIL (TMC).

Recommended Maintenance Practices Manual.

RP 105B Battery Cable Assemblies.

RP 109A Battery Ratings and Engine Cranking Requirements RP 111B Circuit Protections RP 112 Terminals for Heavy Duty Truck-Tractor Primary Wiring Systems.

RP 113A Electrical Systems Connectors.

RP 114A Harness Protection.

RP 118A Turn Signal Switches.

RP 120A Wiring Systems Identification.

RP 137 Antilock electrical supply for tractors through SAE J560 seven pin connector.

RP 138 Auxiliary forward lighting.

RP 321 Fuel Crossover Line Protection and Configuration Guidelines.

RP 325 Radiator Integrity for Highway Trucks.

RP 329 Specifications for Ethylene Glycol Base Coolant Containing Nitrite.

RP 403 Placement of Safety Equipment.

RP 404B Truck and Tractor Access System RP 417 Supporting pneumatic electrical lines between cab and trailer.

RP 418 Heavy-duty, in-cab R134A air conditioning systems.

RP 624 Synthetic Lubricants.

RP 637 Air Dryer Guidelines.

RP 710 Overhead door selection.

RP 711 12 year life swing - type freight van, trailer doors.

Applications for copies of TMC publications should be addressed to:

The Maintenance Council American Trucking Associations 2200 Mill Road Alexandria, VA 22314-5388.)

2.3 ORDER OF PRECEDENCE.

In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specified exemption has been obtained.

2.4 ABBREVIATIONS AND DEFINITIONS.

Following are the abbreviations or contractions and their meanings as they appear and are used in this standard:

ABBREVIATIONS DEFINITIONS

AMP .................. AMPERE

AT ..................... ALL TERRAIN TIRES

AUX .................. AUXILIARY

BAT .................. BATTERY

BBC .................. FRONT BUMPER TO BACK OF CAB

CA .................... CAB TO CENTER OF REAR AXLE

CAP .................. CAPACITY

CM .................... CENTIMETERS

Federal Standard 794AE Page 8 of 78

CYL .................. CYLINDERS

DIA ................... DIAMETER (IN INCHES)

FC ..................... FORWARD CONTROL

FT ..................... FOOT OR FEET

FRT .................. FRONT

GAS .................. GASOLINE

ABBREVIATIONS DEFINITIONS

GAWR .............. GROSS AXLE WEIGHT RATING

GCWR .............. GROSS COMBINED WEIGHT RATING

GHP .................. GROSS HORSEPOWER

GVWR .............. GROSS VEHICLE WEIGHT RATING

H.D. .................. HEAVY DUTY

H.D.A. ............... HEAVIEST DUTY AVAILABLE

HWY ................. HIGHWAY

HYD .................. HYDRAULIC

IN ...................... INCHES

KG .................... KILOGRAMS

L ....................... LITERS

LBS ................... POUNDS

M ...................... METERS

MAN ................. MANUAL

MAX .................. MAXIMUM

MFR .................. MANUFACTURER’S

MIN ................... MINIMUM

MPG ................. MILES PER GALLON

MSPC ............... MFR. STD. PAINT COLOR

N/A ................... NOT APPLICABLE OR NOT AVAILABLE

NHP .................. NET HORSEPOWER

OEM ................. ORIGINAL EQUIPMENT MANUFACTURER

OO .................... ON-OFF ROAD TIRES

OPT .................. OPTION, OPTIONAL

PASS ................ PASSENGERS

PTO .................. POWER TAKEOFF OPENING

RAD .................. RADIAL

RBM ................. RESISTING BENDING MOMENT

SPD .................. SPEED

STD .................. STANDARD (SPECIFICATIONS)

V ....................... V-TYPE (ENGINE)

W/, & W/O ........ WITH, AND WITHOUT

/ ........................ AND

3 REQUIREMENTS.

3.1 STANDARD VEHICLE AND ACCESSORIES.

Except as specified in 3.1.1 through 3.1.1.10, the vehicle, components, assemblies, and accessories to be delivered under the contract shall be standard or optional items, which meet or exceed the requirements of this standard. Except as specified in 3.1.1 through 3.1.1.10, no removal, substitution or alteration of the chassis manufacturer’s standard or optional chassis model components shall be made. All chassis items shall be as represented in the chassis manufacturer’s technical data book. Special bodies or mounted equipment shall be as represented in the body and equipment manufacturer’s

Federal Standard 794AE Page 9 of 78 technical data. Component rated capacities shall not exceed those published in the manufacturers’ technical data. Technical data shall be limited to specifications and technical material, identical to that furnished to the authorized company representatives for selection of vehicle models and components, and shall be available to the engineering offices of the procuring activity, prior to delivery of the items. The chassis model furnished shall be not older than the chassis manufacturer’s current model on the date of invitation for bids.

3.1.1 SPECIAL REQUIREMENTS.

In addition to the standard vehicle and components specified in 3.1, the vehicle shall be furnished with special equipment as specified herein.

3.1.1.1 TREATMENT AND PAINTING.

The vehicle body, including compartments, doors, and tool boxes, except bright finish aluminum and stainless steel, shall be treated and painted in accordance with MIL- HDBK-1223. Interiors on dump bodies need not be painted. The manufacturer’s standard treatment and painting for cab and chassis is acceptable. Unless otherwise specified, the exterior color shall be selected by the manufacturer from one of the manufacturer’s standard, nonmetallic light or medium colors. When specified, color selection will be made after contract award from the standard color charts to be supplied by the manufacturer.

3.1.1.2 DRAIN PLUGS.

Drain plugs installed in manual transmissions, transfer case and rear axles shall be of the permanent magnet type.

3.1.1.3 WOOD TREATMENT.

Unless otherwise specified, the manufacturer’s standard wood treatment is acceptable.

Soft wood shall be pressure treated with a wood preservative. Hardwood need not be treated. When specified, wood shall be treated in accordance with MIL- HDBK-1223.

3.1.1.4 TOWING DEVICES.

Towing devices consisting of two hooks, loops, eyes or pins or the chassis manufacturer’s standard single center mounted eye or pin shall be mounted on the front of the vehicle. All towing devices shall be frame rail mounted or reinforced back to each frame rail.

3.1.1.5 WHEEL SPLASH AND STONE THROW PROTECTION.

Type III stakes, Type IV dumps, Type VII vans, and Type VIII refrigerator vans shall have rubber mud flaps to the rear of the rear wheels. Type II tractors shall have rigid quarter fenders to the front of the rear wheels and rubber mud flaps to the rear of the rear wheels. Tractor mud flaps and their extension supports shall be readily removable, to increase landing wheel clearance, without the use of hand tools. A metal strip not less than 3.2 mm (0.125 in) thick and not less than 25 mm (1 in) wide, extending the entire width of the mud flap, shall be installed to prevent the bolt heads or bolt nuts from damaging the mud flap. As an alternate method of attaching the mud flaps, tabs or clips with minimum surface contact dimensions of 25 mm (1 in) high by 32 mm (1.25 in) wide by 2.4 mm (0.094 in) thick shall be furnished at each bolt. All tilt cabs shall have rubber mud flaps to the rear of the front wheels. All splash shield and mud flap installations, front and rear, shall conform to the rear splash and stone throw protection provisions of SAE J682. The quarter fenders on tractors need extend down only to the height of the

Federal Standard 794AE Page 10 of 78 centerline of the rear axle. Splash shields shall have no advertising or logos, except that of chassis or body manufacturer.

3.1.1.6 BRUSH GUARD.

The 4x4 vehicle shall be equipped with a radiator and headlamp brush guard. When the headlamps are recessed into and protected by the front bumper, a headlamp brush guard is not required.

3.1.1.7 4X4 CONVERSION.

The chassis manufacturer’s standard 4x2 truck chassis may be modified to provide all-wheel drive conforming to the requirements specified herein if:

(a) The conversion axle manufacturer specifically approves and certifies that all such modifications meet the design requirements and standards of the conversion axle manufacturer. Certification shall be based on both design analysis and proving ground test reports.

(b) The chassis manufacturer’s front axle rating before conversion is not exceeded by the conversion axle to be installed.

(c) Components used in the all-wheel drive conversion are of current production.

(d) Components used in the all-wheel drive conversion are approved for the conversion application by the component manufacturers.

(e) The converted vehicle is certified to conform to Federal Motor Vehicle Safety Standard No. 121 by the intermediate or final manufacturer.

(f) Replacement headlights, if required to be added, shall meet the height requirement of not less than 560 mm (22 inches) and not more than 1370 mm (54 inches), measured above the road surface, in conformance with Federal Motor Vehicle Safety Standard No. 108. Replacement headlights shall be equivalent in mounting, protection, range and precision of adjustment to the chassis manufacturer’s original standard headlights.

(g) Unused headlight cavities are covered in a neat workmanlike manner, treated and painted to match the chassis cab color with treatment and painting equivalent to the chassis cab manufacturer’s process for the remainder of the chassis cab.

(h) Complete installation drawings for the specific chassis are available.

(i) Warranty and parts service is available at a facility no more distant than the chassis manufacturers nearest authorized dealer.

3.1.1.8 ELECTRICAL COMPONENTS FOR TRUCK BODIES AND ACCESSORY

EQUIPMENT.

Truck bodies and accessory equipment shall conform to TMC RP 105B, RP 111B, RP 112, RP 113A, RP 114A, and RP 120A when applicable.

3.1.1.9 BRAKE LIGHTS.

At least one pair of brake lights shall override the four-way emergency flasher or the two systems shall be independent of each other. Modifications to the manufacturer’s standard product to accommodate this requirement shall not compromise conformance to any Federal Motor Carrier Safety Regulation referenced herein or to any Federal Motor Vehicle Safety Standard. If additional lights are added to the vehicle, the lights shall be selected from the chassis manufacturer’s standard matching hardware. On

Federal Standard 794AE Page 11 of 78 truck tractors, the brake lights need to override the four-way flasher only when coupled to a semi trailer, in accordance with TMC RP 118A.

3.1.1.10 HYDRAULIC SYSTEM GENERAL REQUIREMENTS.

The following requirements shall apply to vocational hydraulic systems installed on vehicles covered by this Standard. Hydraulic tailgates are exempt from these requirements.

A. Drive systems.

Hydraulic pumps shall be driven by one of the following:

1. Engine or transmission mounted PTO. Pumps shall be flange mounted for transmission mounted PTO. Drive shafts from the PTO to the pump are not acceptable. Belt drives of any type are not acceptable and shall not be used.

2. Electric motor driven pumps (authorized for hydraulic tailgates only) shall be flange mounted to the electric motor.

3. Engine crankshaft front PTO driven. Only OEM integral frame extensions and OEM approved and furnished chassis for front PTO shall be used.

4. Pump support brackets shall be installed from the transmission to support the pump(s) if the combined weight of the pump(s), hoses, and fittings exceed 40 lbs., of if the combined length of the PTO and pump(s) exceeds 18 inches measured form the center-line of the PTO to the end of the pump(s).

5. PTO’s shall be rated at a minimum of 150% of the maximum horsepower requirement of the hydraulic system. The minimum PTO horsepower rating shall be calculated by the following formula:

85.1714

50.1PV

= Minimum PTO HP Rating

Where P = max working pressure in PSI and V = max flow in GPM

6. PTO’s shall be of the power shift design. PTO shift controls shall be electric-over-hydraulic for automatic transmissions, manual transmissions shall have electric shift controls for hydraulic braked chassis and air shift controls for air braked chassis. There shall be a PTO engagement indicator located in the truck cab, in close proximity to control switch. Over speed engagement protection shall be furnished. PTO shall disengage when pre-set engine RPM is reached.

7. The torque or horsepower required of the hydraulic drive PTO shall not exceed the maximum torque or horsepower rating of the PTO opening on the transmission or PTO drive pad on the engine or engine crankshaft.

8. All PTO’s shall be installed within the backlash recommendations of the PTO manufacturer.

B. Hydraulic system hoses, fittings, pressures, and flow rates.

1. Hydraulic hoses shall be rubber covered double wire braid reinforced and comply with SAE 100R2, Type A or AT, or 100R9, type A or AT, of SAE J517.

The working pressure of the hose shall exceed the pressure setting of the relief valve. Hoses shall be sized such that the maximum velocity of hydraulic fluid in the hose does not exceed the following:

Federal Standard 794AE Page 12 of 78

a. Fluid velocity in suction lines shall not exceed 4 ft. / sec.

b. Fluid velocity in discharge lines shall not exceed 25 ft. / sec

2. All hoses shall be installed in accordance with the requirements and recommendations of SAE J1273

3. System working pressures shall not exceed 3500 PSI. A system pressure test port shall be provided. The test port shall be located so that the maximum pressure produced by the system can be monitored without disconnecting any component of the system.

4. Hydraulically actuated implements, such as snowplows, which are deployed while the vehicle is moving, shall be furnished with an automatic reset breakaway mechanism to prevent hydraulic shock if the implement strikes an obstruction while the vehicle is in operation.

5. Hydraulic hose fittings shall comply with the requirements of SAE J516 for permanently attached (crimped) fittings with JIC 37° flare. Field replaceable type fittings are not acceptable. Forged steel hydraulic adapters shall be used.

Cast steel fittings are not acceptable.

C. Pressure protection:

All hydraulic systems shall be furnished with either a spring or pilot actuated pressure relief valve. The relief valve shall be used for overpressure protection only and shall not be used for any flow control purpose. In no case shall a relief valve be set at a pressure higher than the working pressure of the lowest rated component (hose, coupler, adapter, cylinder, etc.) in the system.

D. Flow control valves.

Flow control valves shall be of a type (such as open-center valves) that assures that hydraulic fluid is never deadheaded and forced to flow over the relief valve.

Flow control valves shall be expandable to control multiple devices, either in parallel or in series. Series designed systems shall not exceed the maximum working pressure of any component in the series. Flow control valve body shall not be mounted inside the cab. Flow control valves shall be operated through leavers mounted inside the cab within easy reach of the seated driver. Control leavers shall operate flow control valves through flexible cables or air pressure and permit smooth, infinitely variable operation of equipment through the full designed range of operational travel/speed limits of the equipment.

E. Fluid filtration.

A return line hydraulic filter shall be furnished having a minimum efficiency rating of 99% down to 10-micron size particles and meet or exceed the filtration requirements of the pump, motor, or driven device manufacturer. The filter shall be furnished with a pressure differential type service gage or service indicator.

F. Hydraulic system cooling.

Hydraulic systems shall be designed to operate in ambient temperatures ranging from –20 deg F to +120 deg F.

The hydraulic system shall be designed such that the maximum hydraulic oil temperature does not exceed 200 deg. F. For continuously driven devices, such as spreaders and other motor driven applications, auxiliary cooling, such as air-to-

Federal Standard 794AE Page 13 of 78 oil coolers or water-to-oil coolers, shall be furnished if required to meet the maximum oil temperature requirement. The government reserves the right to request and be furnished test documents showing maximum stabilized temperatures of hydraulic systems.

G. Hydraulic reservoirs.

A stainless steel, aluminum (6061-T6 or 5086-H32 construction only), or other non corroding type hydraulic reservoir shall be furnished and sized such that the reservoir working volume is a minimum of 150% of the maximum hydraulic flow rate. The reservoir shall be furnished with the following:

1. The reservoir shall be furnished with a baffle separating the suction from the return flow.

2. The reservoir shall be furnished with minimum ¾ in. air filtration type breather or combination breather cap with not greater than 10-micron air born particle rating.

3. The reservoir shall be furnished with a sump and valve for draining water from the bottom of the tank and for draining oil.

4. The reservoir shall be furnished with a metal enclosed and protected sight glass for observing oil level.

5. The reservoir shall be furnished with a maximum 300 mesh (50 micron) fill strainer.

6. The reservoir shall incorporate a return tube that discharges return oil below the surface of the reservoir oil.

H. Hydraulic oil.

Hydraulic oils shall meet the minimum requirements of the hydraulic pump or other critical component manufacturer(s). Water based hydraulic fluids shall not be used. A nameplate shall be affixed near the fill cap on the reservoir indicating the type of oil to be used. See 3.1.1.6.

I. Installation and workmanship.

The hydraulic system shall comply with the following requirements:

1. All tapered threaded fittings shall be installed using an anti-seize thread sealing compound. Teflon tape is not acceptable.

2. Hoses shall be routed for easy tracing of hoses and shall be protected with grommets when passing through bulkheads. Hoses shall be protected from abrasion when routed over or through bare metal edges.

3. Hydraulic hoses shall be supported with metal hose clamps that provide protection for the hose from the metal portion of the clamp. Hoses shall not be allowed to droop or to be entangled with other hoses or lines. The clamps shall be spaced not more than 18 in. apart.

4. Overhanging weight of fittings, hoses, valves, or piping shall be supported from the reservoir to eliminate flexing of sidewalls.

5. All hoses shall be routed and installed in accordance with the requirements and recommendations of SAE J1273. Special attention to routing and installation shall be given to avoid the following:

Federal Standard 794AE Page 14 of 78

a. Tensile loads on the hose

b. Side loads

c. Flattening

d. Kinking

e. Thread damage

f. Damage to sealing surfaces

g. Abrasion

h. Twisting

i. Exceeding minimum hose bend radius

j. Operational Test

The hydraulic system and hydraulically driven components shall be operated and checked for leaks and proper operation. The operational test shall include the maximum requirements (height, extension, speed, etc.) of the driven devices under no-load conditions. No leakage is permitted beyond a class “1” leak in accordance with SAE J1176-External Leakage Classifications for Hydraulic Systems.

3.2 GENERAL DESIGN.

3.2.1 FEDERAL MOTOR VEHICLE SAFETY STANDARDS.

The vehicle furnished accessories shall comply with all Federal Motor Vehicle Safety Standards in effect on the date of manufacture.

3.2.2 AIR POLLUTION CONTROL.

The vehicle and engine shall conform to 40 CFR Subchapter C-Part 86 - “Control of Emissions from New and In-use Highway Vehicles and Engines", as evidenced by an EPA certificate of compliance. Vehicles shall also comply with all pollution control requirements for the state of final destination. Certificates of compliance shall be made available upon request.

3.2.3 SOUND LEVEL.

The cab interior sound level shall not exceed 84 db(A) when measured in accordance with Federal Motor Carrier Safety Regulation 393.94. The vehicle exterior sound level shall conform to the Environmental Protection Agency Noise Emission Standards for Transportation Equipment, Medium and Heavy Trucks.

3.2.4 CURB WEIGHT.

The curb weight is defined as the empty weight (no payload included) of a fully equipped truck. Curb weight shall include the chassis-cab, body or fifth wheel for Type I chassis, all attached devices, equipment, and full complement of fuel, lubricants, and coolants.

3.2.5 GROSS VEHICLE WEIGHT.

The gross vehicle weight (GVW) shall consist of the curb weight, operator and passenger weight (computed at 80 kg (175 lb each) and a payload to provide not more than the specified GVWR.

Federal Standard 794AE Page 15 of 78

3.2.6 SPECIFIED GAWR.

Class D, GVWR shall not exceed 11,800 kg (26,000 lb), without written approval of customer agency. Except Type II tractors, which are all subject to excise tax, Class F, vehicles shall not exceed 15,000 kg (33,000 lb) GVWR, without written approval of customer agency.

3.2.7 GROSS COMBINATION WEIGHT.

Gross combination weight (GCW) shall consist of the truck or truck tractor curb weight, operator and passenger weight (computed at 80 kg (175 lb) each), and the weight of a trailer loaded to provide not less than the specified GCW. The fifth wheel shall be located so that with the truck tractor loaded to GVWR, the load rating of the chassis components are not exceeded.

3.2.8 WEIGHT DISTRIBUTION.

Except as specified in option codes MPR and MPS, the distribution of GVW for the purpose of establishing suspension, axle and tire capacities shall be determined with the payload uniformly distributed over the load area. For Type II tractors furnished with a sliding fifth wheel, option code ARW, the weight distribution shall be determined with the sliding fifth wheel in its most forward position of adjustment.

3.2.9 RATINGS.

Vehicle ratings shall be the manufacturer’s published ratings. Component and vehicular ratings shall not be raised to meet the requirement of this specification. Minimum GVWR and GCWR shall conform to Figure 1 for the specified class of vehicle. All individual components, including engine, transmission, driveline and drive axle, shall have a minimum GCWR specified for each class.

Figure 1

GVWR and GCWR Minimums

VEHICLE

CLASS GVWR, KG (LBS) GCWR, KG (LBS)

C 9,500 (21,000) 13,650 (30,000)

D 11,500 (25,500) 19,500 (43,000)

E 12,700 (28,000) 20,400 (45,000)

F 14,500 (32,000) 24,950 (55,000)

G 15,900 (35,000) 27,200 (60,000)

3.2.10 OVERALL WIDTH.

The overall width of the vehicle, exclusive of tires, wheel nuts and safety related items such as mirror, lights, and reflectors shall be not more than 2440 mm (96 inches). The width over the tires shall be not more than 2540 mm (100 inches).

3.2.11 ACCESSIBILITY.

The design of the vehicle and optional equipment shall permit access for routine servicing and shall permit access for replacement and adjustment of component parts and accessories with minimal disturbance of other components and systems.

3.2.12 RECOVERED MATERIALS / REGULATORY REQUIREMENTS.

In accordance with Section 23.403 of the Federal Acquisition Regulations, the Government’s policy is to acquire items composed of the highest percentage of recovered materials practicable, consistent with maintaining a satisfactory level of competition without adversely affecting performance requirements or exposing supplier’s employees to undue hazards from the recovered materials. The term

Federal Standard 794AE Page 16 of 78

“recovered materials” means materials that have been collected or recovered from solid waste and reprocessed to become a source of raw materials, as opposed to virgin raw materials. None of the above shall be interpreted to mean that the use of used or rebuilt products is allowed under this document. The use of re-refined oil shall not be prohibited. This does not prohibit vehicle manufacturers from using performance criteria for acceptable oil. Any re-refined oil products shall meet the performance criteria of the vehicle and component manufacturers.

3.3 PERFORMANCE.

3.3.1 MAXIMUM VEHICLE SPEED

The maximum vehicle governed speed shall be not less than 113 km/h (70 mph) or more than 121 km/h (75 mph) for 4x2 and not less than 96 km/h (60 mph) or more than 104 km/h (65 mph) for 4x4. Under no circumstance shall the vehicle maximum governed speed exceed the speed rating of any of the furnished tires.

3.3.2 SERVICE BRAKES.

On all vehicles except Type II tractors, the service brakes shall stop the vehicle, loaded to specified GVW, within the stopping distance requirements of Federal Motor Carrier Safety Regulation 393.52. The service brakes on Type II tractors shall stop the tractor-semitrailer combination, loaded to specified GCW, within the stopping distance requirements of Federal Motor Carrier Safety Regulation 393.52. All service brakes shall be of the self-adjusting type.

3.4 CHASSIS COMPONENTS.

3.4.1 ENGINE.

The engine furnished for the specified vehicle class shall be the chassis manufacturer’s standard or optional engine for the commercial model truck that meets or exceeds the requirements of this specification.

3.4.1.1 DIESEL ENGINE.

Unless otherwise specified, the vehicle shall be equipped with a liquid cooled, compression ignited, diesel engine, electronically controlled, with not less than six cylinders.

3.4.1.2 OIL FILTER.

A full flow or combination full flow and bypass oil filter with replaceable element shall be furnished.

3.4.1.3 GOVERNOR.

An engine governor shall be furnished and set and sealed to limit the engine to the engine manufacturer’s recommended operating speed.

3.4.1.4 COOLING SYSTEM.

The chassis manufacturer’s heaviest duty cooling system for the model provided shall be supplied. The cooling system shall include a surge tank or a coolant recovery reservoir of not less than 1.89 L (two quart) capacity. On tilt cab models, a radiator servicing access door shall be provided if needed to allow verification of the coolant level without tilting the cab. For all Item numbers, the radiator furnished shall conform to TMC RP 325.

Federal Standard 794AE Page 17 of 78

3.4.1.4.1 COOLANT TEMPERATURE CONTROL.

Thermostatic control of engine coolant temperature shall be provided. On diesel engine driven vehicles, the control shall include complete thermostatic control of all coolant flow through the radiator.

3.4.1.4.2 ENGINE COOLANT.

The engine coolant shall be a solution of chassis manufacturers ethylene glycol antifreeze and water or propylene glycol antifreeze and water, in equal parts of antifreeze and water by volume (-36°C (-34°F protection)). The coolant supplied shall comply with TMC-RP329 or TMC-RP330 as applicable.

3.4.1.4.3 ENGINE BLOCK HEATER

Engine block heater of the OEM chassis manufacturer’s 110/120 – volt design shall be furnished. A 25 ft. long commercial grade outdoor rated power line cable with in-line automatic reset Ground Fault Circuit Interrupter (GFCI) shall be furnished. The furnished power cable shall be UL Listed and rated no less than 10% greater than the maximum capacity of the furnished block heater.

3.4.1.5 FAN CLUTCH.

A fan clutch shall be provided. The fan clutch shall reduce the fan speed automatically when the fan is not required for engine cooling. The fan clutch shall be asbestos free.

3.4.1.6 ELECTRONIC THROTTLE CONTROL.

An electronic hand throttle control with quick release shall be furnished.

3.4.2 ELECTRICAL SYSTEM.

The electrical system shall be in accordance with Federal Motor Carrier Safety Regulations 393.27 through 393.31 and 393.33.

3.4.2.1 STARTING SYSTEM.

A 12-volt engine starting system, with 12-volt direct current (DC) lighting system shall be furnished. On diesel engines 8L and larger, the electric starter motor shall be equipped with a thermostat controlled, automatic resetting circuit breaker to protect the motor from over crank heat damage. Easily accessible remote jump - start post(s) shall be furnished, within close proximity to the battery box. Posts shall be furnished with protective rubber or plastic type covers that are tethered to prevent loss. Jump start posts are not required on electric and hybrid vehicles.

3.4.2.2 ALTERNATOR.

Unless otherwise specified, a minimum 130-ampere alternator shall be provided. The alternator output with the engine at idle speed shall be not less than 70 amperes.

3.4.2.3 LIGHTING.

All vehicle lights, reflectors, and wiring shall conform to Federal Motor Carrier Safety Regulations 393.19, 393.20 and 393.22 through 393.26(d). LED lighting shall be provided on all vocational body lamps. All added stop/tail directional, and marker lights shall be light emitting diodes. LED lights shall be installed with tamper resistant hardware.

Type I chassis need not be furnished with rear identification lamps or clearance lamps and reflectors. Type IV dump rear lighting shall be positioned or guarded to prevent damage during dumping of the cargo. Positioning and guarding shall permit normal replacement of the bulbs and lenses. Lights and reflectors shall not be mounted on

Federal Standard 794AE Page 18 of 78 vertical surface of rub rails (unless recessed and fully protected) or mounted on vehicle bumpers. When right hand drive is specified by acquisition documents, left-dip headlights shall be provided. Left-dip headlights may be provided as a replacement set, stowed in the cab for shipment. Daytime running lights shall be furnished, in accordance with FMVSS 108, and TMC RP 138. Truck bodies shall be furnished with conspicuity markings in accordance with FMVSS 49 CFR Part 571.108.

3.4.2.4 TURN SIGNALS.

Turn signal control shall be mounted on the steering column. Type II tractor turn signal units shall be visible when not in combination with a towed vehicle. Turn signals shall have visible flash indicators. Temporary mounting for rear signal units shall be provided on chassis models. Turn signals shall conform to TMC RP 118A.

3.4.2.5 LIGHTING CABLE FOR TYPE II TRUCK TRACTOR.

The semitrailer lighting cable for Type II tractors shall conform to SAE J1067. The cable shall incorporate a connector conforming to SAE J560 on both ends of the cable and a weather proof receptacle conforming to SAE J560 shall be mounted in the back wall of the cab . The cable shall be coiled and shall have an extended length of not less than 110 inches. The SAE J560 connector shall include a grip for withdrawing from the cab and semitrailer receptacle. Support for the cable shall be provided by the means of a hook and hanging loop or a protective holding bracket. Unless otherwise specified, support shall be by:

(a) A hook provided on the rear of the truck tractor cab.

(b) A hook on a pogo-stick type hose tender.

(c) A protective bracket mounted at the rear of the cab below the roofline. Each shall hold the cable plug so as to prevent water from entering the terminals.

The lighting cable; when on the hook, loop or protective bracket; shall be accessible to an operator standing on the ground to the rear of the cab, on the street side of the vehicle.

3.4.2.6 BATTERIES.

Each battery shall be of 12-volt potential. The total reserve capacity ratings and the total cold cranking ampere ratings at -18°C (0°F), both measured in accordance with SAE J537, shall be not less than specified in Figure 2. The batteries shall be of the maintenance-free type having the maintenance-free characteristics listed in A-A-55439.

Batteries shall conform to TMC RP 109A.

Figure 2

Batteries

RESERVE CAPACITY

COLD

CRANKING

ENGINE

TYPE

(MINUTES) (AMPERES)

Diesel engine

540 1875

Gasoline engine

115 535

Federal Standard 794AE Page 19 of 78

3.4.2.7 RADIO INTERFERENCE SUPPRESSION.

The vehicle shall be suppressed to limit electromagnetic radiation in accordance with SAE J551. Any body equipment emitting electromagnetic radiation shall be suppressed to the same level as the vehicle chassis.

3.4.3 FUEL SYSTEM.

The fuel system shall conform to Federal Motor Carrier Safety Regulations 393.65 and 393.67.

3.4.3.1 AIR CLEANER.

A dry type air cleaner shall be provided.

3.4.3.2 FUEL TANK(S).

Except as specified for Type II tractors or unless otherwise specified for other vehicle types, fuel tanks shall be not less than 189 L (50 gallons) total capacity. Type II tractors shall be equipped with fuel tank(s) of not less than 378 L (100 gallons) total capacity.

When more than one fuel tank is furnished on diesel engine driven vehicles, means shall be provided to assure equalized fuel level in both tanks. When more than one tank is furnished on gasoline engine driven vehicles, a selector valve connecting either tank to engine fuel intake shall be provided and means shall be provided to monitor the fuel level of either tank from a single fuel gage; or an equalizing pump shall be used to maintain the same fuel level in both tanks. When fuel crossover lines are furnished they shall be in accordance with TMC RP 321.

3.4.3.3 FUEL AND WATER SEPARATOR.

The manufacturer’s standard or optional fuel filter shall be provided. A fuel and water separator shall also be furnished for diesel engines. The separator shall include water coalescent and a drain valve. A combination filter/separator unit may be provided. See option FFS for heated fuel and water separator.

3.4.4 EXHAUST SYSTEM.

The exhaust system shall conform to Federal Motor Carrier Safety Regulation 393.83.

3.4.5 TRANSMISSION.

Unless otherwise specified, the vehicle shall be equipped with an Allison or equal automatic transmission model 2500RDS, 3500RDS or 4500RDS as applicable for engine supplied. The automatic transmission shall include a hydraulic torque converter and not less than five forward gear ratios. Normal driving range selector position shall provide not less than five gear ratios without movement of the selector. The net torque capacity and the net power rating of the transmission shall exceed the maximum output ratings of the engine in all gears. The transmission shall be provided with power takeoff provisions to include gear and opening.

3.4.5.1 TRANSFER CASE.

A two-speed transfer case shall be provided on 4x4 vehicles.

3.4.6 DRIVELINE COMPONENTS.

Driveline components shall be rated to transmit the maximum delivered torque of the engine, as developed through the maximum gear train reduction. The drive shaft for front mounted winches shall have an angle not greater than 16 degrees from the longitudinal plane. Components shall be rated no less than the GCWR in 3.2.9.

Drivelines shall be balanced and free of vibration.

Federal Standard 794AE Page 20 of 78

3.4.7 FRAME.

The chassis frame shall be the manufacturer’s standard for the type and class vehicle furnished. Reinforcements shall extend at least from the rear of the front suspension, rear hanger bracket to the front of the rear spring, front hanger bracket. Reinforcements for Type III stake dumps and Type IV dumps shall provide sufficient structural strength in the chassis frame, through increased resisting bending moment (RBM), to at least equal the loads imposed, with the dump truck loaded to provide specified GVW. Frame reinforcement for Type III stake with crane shall be in accordance with the body manufacturer’s recommendations for the size of the crane furnished. Frame rails shall not project beyond the rear end of the body. Unless otherwise specified, on Type II tractors, the chassis frame rails shall be cut off immediately to the rear of the rear spring rear hanger brackets or the frame crossmember closest to the rear of these brackets.

When a RBM is specified, any frame combination of yield strength and section modulus that provides the required RBM is acceptable.

3.4.8 SUSPENSION.

Except as specified in option codes MPR and MPS, the vehicle shall be equipped with a suspension system with components having a rated capacity at least equal to the load imposed on each member, measured at the ground, with the vehicle loaded to specified GVW. When suspension is rated at the spring pads, un-sprung weight shall be deducted. The vehicle shall be equipped with hydraulic, double-acting shock absorbers at the front wheels.

3.4.9 AXLES.

Except as specified in option codes MPR and MPS, axle ratings shall be at least equal to the load imposed on each axle, measured at the ground, with the vehicle loaded to specified GVW. The wheel bearings and axle spindles shall be oil lubricated or of a unitized, lifetime sealed no-maintenance design, except on front drive axles. For oil filled hubs, a window shall be provided for visual determination of oil level and provisions for venting or withstanding internal pressure buildup and for replenishing the oil supply shall be provided.

3.4.9.1 TRACTION CONTROL.

Automatic traction control shall be provided on all Type IV dumps. Maximum traction capabilities shall be maintained at all times under each drive wheel(s) for the life of the vehicle.

3.4.10 WHEELS, RIMS AND TIRES.

Unless otherwise specified, the vehicle shall be equipped with single front and dual rear wheels. Unless otherwise specified Hub piloted, disc type wheels shall be furnished.

Disc wheel sizes shall be the same for all wheels except where required otherwise. Tire size and load range (ply rating) shall be the same for all tires except class F vehicles or where required to be otherwise. The rear axles of dump trucks shall have Goodyear G282MSD, Michelin XDE M/S or equal tires. Tire and wheel assemblies shall be balanced. When the front tires extend beyond the cab fenders, rubber fender extensions extending at least to the outside of the tire tread shall be furnished. Tires and wheels shall conform to Tire and Rim Association or to the European Tyre and Rim Technical Organization recommendations for the type and size furnished. Under no circumstance shall the vehicle maximum governed speed exceed the speed rating of any of the furnished tires or wheels.

Federal Standard 794AE Page 21 of 78

3.4.10.1 TIRES.

Unless otherwise specified, standard profile steel belted radial ply tires shall be provided. Tires shall have highway tread on 4x2 vehicles and all terrain (AT) tires or on-off road (OO) tires on 4x4 vehicles, and the rear axle of dump trucks. Tires shall be of the tubeless type. Except as specified in option codes MPR and MPS, tires shall be of rated capacity at least equal to the load imposed on each tire, measured at each wheel, at the ground, with the vehicle loaded to specified GVW. Tires shall conform to the Tire and Rim Association or to The European Tyre and Rim Technical Organization recommendations.

3.4.10.2 TIRE CHAIN CLEARANCE.

Tire chain clearance in accordance with SAE J683 shall be provided. Allowance for spring deflection shall be included.

3.4.11 BRAKES.

Brakes shall conform to Federal Motor Carrier Safety Regulations 393.40 through

393.43 and 393.45 through 393.52. Brake linings shall be of non-asbestos material.

Class C vehicles shall be equipped with power assisted, hydraulic or air-hydraulic, service brakes.

3.4.11.1 AIR BRAKES.

The class D, E, F and G vehicles shall be equipped with full-air brakes. The braking system, complete with all necessary components, shall include:

(a) Air compressor, unloader-head type, engine driven and engine lubricated, air or water cooled, and having a capacity of not less than 340 L/min (12 cubic feet per minute (cfm)).

(b) Air storage reservoir(s), each tank equipped with drain, and with safety and check valves between the compressor and the last reservoir tank

(c) Foot control, suspended or treadle type

(d) Air control valves

(e) Air pressure gage, visible to the driver

(f) Low air pressure warning, visible and audible

(g) Service brake stop lamp switch

(h) Automatic moisture ejector on primary air storage reservoirs

(i) Automatic slack adjusters on cam type brakes or internal self-adjusting brakes on wedge and disc…

This is the start of the file's text. The full file is on GovTribe.

File details come from the government source that posted it. Updated .