Fed Std 833P Items 240L Light Duty Shuttle Low-Floor.pdf

Fed Std 833P Items 240L Light Duty Shuttle Low-Floor.docx 2

U.S. General Services Administration

Federal Standard 833P

July 27, 2020

LIGHT-DUTY SHUTTLE BUS, LOW-FLOOR, BASIC

STANDARD ITEM NUMBERS:

240L

Fed Std 833P Items 240L Light Duty Shuttle Low-Floor.docx 2

TABLE OF CONTENTS

Note: You may click on a heading to automatically scroll there

1. SCOPE, PURPOSE, & CLASSIFICATION

2. APPLICABLE DOCUMENTS

3. REQUIREMENTS

3.1 BODY & CHASSIS

3.2 AIR POLLUTION CONTROL

3.3 ENGINES

3.4 ENGINE ACCESSORIES

3.5 TRANSMISSION

3.6 BRAKES

3.7 AXLES

3.8 ELECTRICAL

3.9 FUEL

3.10 EXTERIOR

3.11 DOORS AND WINDOWS

3.12 LIGHTS AND LIGHTING

3.13 ELECTRONICS/AUDIO VISUAL

3.14 INTERIOR

3.15 FLOOR

3.16 WALLS

3.18 SEATS

3.19 SAFETY

3.20 SUSPENSION

3.21 TIRES AND WHEELS

3.22 MISCELLANEOUS

3.26 GENERAL WORKMANSHIP REJECTION STANDARDS

3.27 IDENTIFICATION OF VEHICLES

3.28 CERTIFICATE OF ORIGIN OR BILL OF SALE

3.29 WARRANTY REQUIREMENTS

3.30 EXCEPTIONS TO WARRANTY

3.31 DETECTION OF DEFECTS

3.32 SCOPE OF WARRANTY REPAIRS

3.33 FLEET DEFECTS

3.34 INTENDED USE

3.35 REPAIR PARTS AND SERVICE

3.36 DOMESTIC USE

3.37 FOREIGN USE

4.1 VERIFICATION

4.2 FIRST PRODUCTION VEHICLE INSPECTION

4.3 INSPECTION OF PRODUCTION VEHICLES

5. NOTES

5.1 ORDERING DATA

5.2 DEVIATION FROM FEDERAL STANDARD

5.3 CHANGES AND NOTICES

Fed Std 833P Items 240L Light Duty Shuttle Low-Floor.docx 3

1. SCOPE, PURPOSE, & CLASSIFICATION

1.0 SCOPE

This specification identifies the minimum requirements for new commercial Light-Duty Shuttle

Buses with a low-floor configuration. This category is intended for shuttle buses with a capacity of

10 adults but can also vary based on wheelchair positions and floorplans.

This standard is intended to simplify competitive procurement of commercial vehicles and achieve a practical degree of standardization within the federal fleet. The Government takes no exemptions to the laws and regulations for vehicles used on public roads and highways.

1.2 APPLICATION

This Standard does not include all varieties of the commodity indicated by the title but is intended to cover those vehicles generally acquired by the Government. Buses with standardized components and equipment are highlighted in this Standard. A selection of coded optional additional systems and equipment are included for agencies, divergent geographic and operational related needs.

1.3 COVERAGE OF BUS TYPES

The types of buses covered by this standard are listed below. Optional equipment appears in section

Appendix A and beneath each relevant section in the requirements.

The item descriptions, minimums, options, and manufacturer data can be viewed on this website:

www.gsa.gov/automotive. Click on the link for all standards and refer to Federal Standard 833.

1.4 CLASSIFICATIONS

- The individual bus configuration classifications are referred to by a Standard Item Number (SIN)

- The SINs covered by this specification are as follows:

o 240L- 10 Adult, Low Floor, Light-Duty Shuttle http://www.gsa.gov/automotive

Fed Std 833P Items 240L Light Duty Shuttle Low-Floor.docx 4

2. APPLICABLE DOCUMENTS

2.1 FEDERAL SPECIFICATION

2.1.1 ADA Transportation Vehicle Accessibility Guidelines (ADA) 36 CFR Part 1192

2.1.2 Federal Motor Vehicle Safety Standards (FMVSS) 49 CFR Part 571

2.1.3 Federal Motor Carrier Safety Regulations (FMCSR) 49 CFR Part 393

2.1.4 A-A-393A Commercial Item Description Extinguishers, Fire, Dry-Chemical

2.2 NON-GOVERNMENT STANDARDS

2.2.1 Society of Automotive Engineers (SAE) Standards and Recommended Practices

- J163 Low Tension Wiring and Cable Terminals and Splice Clips

- J198 Windshield Wiper Systems- Trucks, Buses, and Multipurpose Vehicles

- J381 Windshield Defrosting Systems Test Procedure and Performance Requirements

- J551 Performance Levels and Methods of Measurement of Electromagnetic Compatibility of Vehicles

- J516 Hydraulic Hose Fittings

- J537 Storage Batteries

- J561 Electrical Terminals-Eyelets and Spade Type

- J588 Turn Signal Lamps for Use on Motor Vehicles Less than 2032 mm in Overall Width

- J589 Turn Signal Switch

- J673 Automotive Safety Glasses

- J686 Motor Vehicle License Plates

- J695 Turning Ability and Off Tracking-Motor Vehicles

- J844 Nonmetallic Air Brake System Tubing

- J910 Hazard Warning Signal Switch

- J1127 Battery Cable

- J1128 Low Tension Primary Cable

- J1149 Metallic Air Brake System Tubing and Pipe

- J1292 Automobile, Truck, Truck-Tractor, Trailer, and Motor Coach Wiring

- J1908 Electrical Grounding Practice

- J2064 R134a Refrigerant Automotive Air-Conditioning Hose

- J2188 Commercial Truck and Bus SAE Recommended Procedure for Vehicle Performance Prediction

2.2.2 American Society of Heating, Refrigeration and Air-Conditioning Engineers (ASHRAE)

- A03 Handbook, Chapter 9, Surface Transportation

- 37 Standard Methods of Testing for Rating Unitary Air-Conditioning and Heat Pump Equipment

- 41.1 Standard Methods for Temperature Measurement

- 41.2 Standard Methods for Laboratory Airflow Measurement

- 41.3 Standard Method for Pressure Measurement

2.2.3 American Trucking Association, Inc.

- Technology and Maintenance Council (TMC) RP 803

2.3 ORDER OF PRECEDENCE

In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. However, nothing in this document supersedes applicable laws and regulations unless a specific exemption has been obtained https://www.law.cornell.edu/cfr/text/36/part-1192 https://www.law.cornell.edu/cfr/text/49/part-571/subpart-B https://www.fmcsa.dot.gov/regulations/title49/part/393 http://everyspec.com/COMML_ITEM_DESC/A-A-00000_A-A-00999/A-A-393A_8414/ https://www.sae.org/standards/content/j163_201102/ https://www.law.cornell.edu/cfr/text/49/571.104 https://www.sae.org/standards/content/j381_196802/ https://www.sae.org/standards/content/j551/1_200610/ https://www.sae.org/standards/content/j516_201110/ https://www.sae.org/standards/content/j537d_196612/ https://www.sae.org/standards/content/j561_200604/ https://www.sae.org/standards/content/j588_201108/ https://www.sae.org/standards/content/j589_196404/ https://www.sae.org/standards/content/j673a_196708/ https://www.sae.org/standards/content/j686a_196807/ https://www.sae.org/standards/content/j695_199812/ https://www.sae.org/standards/content/j844_200411/ https://www.sae.org/standards/content/j910a_196902/ https://www.sae.org/standards/content/j1127_201210/ https://www.sae.org/standards/content/j1128_201310/ https://www.sae.org/standards/content/j1149_199106/ https://law.resource.org/pub/us/cfr/ibr/005/sae.j1292.1981.pdf https://www.sae.org/standards/content/j1908_200711/ https://www.sae.org/standards/content/j2064_201102/ https://www.sae.org/standards/content/j2188_200310/ https://www.ashrae.org/technical-resources/ashrae-handbook/description-2017-ashrae-handbook-fundamentals http://www.ahrinet.org/App_Content/ahri/files/STANDARDS/AHRI/AHRI_Standard_210-240_2017.pdf https://global.ihs.com/doc_detail.cfm?document_name=ASHRAE%20STD%2041%2E1&item_s_key=00011567 https://global.ihs.com/doc_detail.cfm?document_name=ASHRAE%20STD%2041%2E1&item_s_key=00011567 https://www.ashrae.org/news/esociety/new-updated-standards-june-2018 https://global.ihs.com/doc_detail.cfm?document_name=ASHRAE%20STD%2041%2E3&item_s_key=00111047 https://www.trucking.org/ATA%20Docs/About/Organization/TMC/Documents/RP_MANUAL_DESCRIPTIONS.pdf

Fed Std 833P Items 240L Light Duty Shuttle Low-Floor.docx 5

3. REQUIREMENTS

3.1 BODY & CHASSIS

3.1.1 PASSENGER CAPACITIES

Standard Item Number

(SIN)

Adult Capacity

(Seated)

SIN 240L 10 adults

3.1.3 BODY FASTENER APPLICATION

-If fasteners are used in the body, they shall be corrosion resistant.

3.1.4 BODY STRUCTURE

-Wood shall not be used for structural framing.

3.1.5 BODY INTEGRITY

-The body, floor, roof, and panel joints shall be water and air resistant.

-All body seams shall be sealed and not permit dust or fume entry into passenger compartment.

-Body, hinge, and, mirror mounting points shall be reinforced to prevent cracking and fastener or fastener device pull out.

3.1.6 BODY EXTERIOR LENGTHS

-Body measurement shall be exterior rear surface to front face of body. Length measurement shall include bumpers.

-Bus body lengths shall not be changed to accommodate space consuming optional equipment. Only one body length shall apply to each SIN.

3.1.8 BODY EXTERIOR

-Bus exterior panels, roof, and end caps may be of composite or metal construction.

-Tires shall not protrude beyond exterior body side wall.

-Composite rubber fender extensions or molded high impact plastic body accents may be used to cover tire edge.

3.1.9 RAIN SPLASH CONTROL

-An integrated roof design for rain directional control shall be provided to prevent water from the roof flowing onto the passenger doors, side windows, and the door boarding area.

3.1.10 PASSENGER COMPARTMENT INTERIOR DIMENSIONS

-Interior height should be measured from the floor to center peak of ceiling.

3.1.11 INSULATION

-All bus and chassis manufacturers supplied insulation packages shall comply with FMVSS 571.302.

3.1.12 MAINTENANCE

-The design of the bus and optional equipment shall permit access for routine servicing and shall permit access for replacement and adjustment of component parts and accessories with minimal disturbance of other components and systems.

-Interior hinged and fastener-secured access panels and doors for maintenance must:

Use common tools to open and be flush with the surrounding materials.

Be sealed to prevent entry of fumes and water into passenger compartment.

https://www.law.cornell.edu/cfr/text/49/571.302

Fed Std 833P Items 240L Light Duty Shuttle Low-Floor.docx 6

3.1.13 SOUND LEVEL

-The interior sound level when measured in accordance with FMCSR 393.94 shall not be greater than 82db.

-This requirement shall be expanded to include any location within the passenger compartment.

-All noise reduction methods available from body and chassis manufacturer shall be added to the standard package. Examples of noise reduction methods that may be included as standard include:

Complete lining of stepwell treads and sides with multiple layer noise reduction matting

Urethane foam underbody insulation

Application of PPG Audio guard acoustical coating

Underbody shielding

Engine compartment and under hood noise control matting.

3.1.14 BODY MOUNTING

- Lightweight modular composite bus structure on a purpose built high strength steel lowered floor chassis, Composite side panels and roof panels coupled with a high strength aluminum structural joiner shall be acceptable.

-Cushion material shall be utilized between body and frame. Body can be floated but shall not include wooden spacer blocks.

-Reinforcements or filler blocks shall be used where mounting devices might otherwise deform frame flanges.

-Mounting devices shall utilize fasteners that will minimize loosening, but which may require regular scheduled tightening.

-Interface of chassis and body, including all electrical, fluid, mechanical systems, and mounted equipment shall be in full accordance with the chassis manufacturer’s “Body Builders Book” and published equipment technical data.

3.1.15 CORROSION PROTECTION

-All hardware shall be corrosion resistant.

-Fastener materials shall be compatible with materials being fastened.

-No bare metal permitted.

-All joints and connections of dissimilar metals shall be insulated to minimize effects of galvanic corrosion.

3.1.16 UNDERCOATING

-Unprotected underbody, fenders, skirts, and wheel wells shall be undercoated. The exceptions to this requirement are parts and surfaces that are constructed of or coated with corrosion protected materials (plastic, polymer, stainless steel, e-coat, Powder Coat, epoxy, etc.).

-Hot dip galvanizing shall also be acceptable

3.1.17 MUD FLAPS

-Mud flaps are required if the wheel wells do not have an integrated method of blocking debris thrown into the air by the rotating tire.

-Rubber composition mud flaps at all wheel ends shall extend to within 3 to 7 inches off the ground when suspension is at normal operating height and at curb weight.

3.1.18 CURB WEIGHT

-The curb weight shall include the weight of the chassis and body with all attachments, accessories, standard and optional equipment, a full complement of fuel, lubricants, coolants.

3.1.19 PAYLOAD AND GROSS VEHICLE WEIGHT

-The payload weight for adult passengers shall be calculated using 215 pounds per person and 215 pounds for the driver. These ratings include provisions for parcels and shall be considered an even weight distribution throughout the body. -Wheelchair positions shall be calculated using 300 lbs. for each wheelchair position specified. When a wheelchair position includes convertible seating, the 215 pounds per seated person shall be included in the calculation instead of 300.

Fed Std 833P Items 240L Light Duty Shuttle Low-Floor.docx 7

3.1.20 CAPACITY DECAL

-An instruction decal shall be applied to the forward bulkhead visible to all passengers and driver. The lettering shall be not less than 1-1/2 inch in height and in strong contrast to the interior background color.

-The message can be in a single line or two lines and must state “No Standees Permitted” or “No Standees” and “Maximum Passenger Capacity XX” or “Capacity XX Passengers”. The two X’s shall represent the passenger capacities specified as standard and optional.

-Multiple decals can be used to accommodate this requirement with one displaying the no standees instruction statement and another displaying passenger capacity.

3.2 AIR POLLUTION CONTROL

-The vehicle and engine shall confirm to 40 CFR Subchapter C-Part 86“Control of Emissions from New and In-use Highway Vehicles and Engines,” as evidenced by an EPA certificate of compliance.

-Vehicles shall also comply with all pollution control requirements for the State of final destination. - Certificates of compliance shall be made available upon request.

3.3 ENGINES

3.3.1 COOLING SYSTEM

-Cooling system shall be charged with extended life coolant.

-All coolant hoses and lines shall meet or exceed the requirements of SAE J20 D2.

-All hoses and lines shall be securely attached with constant-tension or thermoplastic clamps. Hoses and lines shall not be permitted to rub components that may eventually lead to a coolant leak.

-Passenger compartment heater hoses shall be equipped with manual or electric full-flow valves located in a protected location to permit complete shutoff of engine coolant flow to heating units. The location of manual valves shall be indicated with a label stating the purpose of the valves such as “Heater Shutoff Valves” and located to be visibly obvious.

3.3.2 ENGINE COMPARTMENT

-Engine compartment shall be readily accessible for servicing and routine maintenance of engine and engine components.

-All fluid locations shall be accessible with standard funnels, pour spouts, and automatic dispensing equipment.

-All lubricant sumps shall be fitted with magnetic-type external, drain plugs if available from the component manufacturer as standard or optional.

3.4 ENGINE ACCESSORIES

3.4.4 HIGH-IDLE CONTROL

Automatic engine high-idle control shall:

Be preset to operate at an elevated rate not to exceed the maximum rate permitted by engine manufacturer.

Operate (engage) when switched to the “ON” position and the transmission in “NEUTRAL” or “PARK” (applicable to design furnished).

Operate (engage) when the air conditioning is operating and the transmission in “NEUTRAL” or

“PARK”.

Not rely on manual on/off switch position to elevate idle. A low voltage sensing controller can be used to accommodate this requirement in lieu of immediate idle up when A/C is activated.

Disengage when the service brake pedal is pressed, or the transmission in-gear position is selected.

https://www.law.cornell.edu/cfr/text/40/part-86 https://www.law.cornell.edu/cfr/text/40/part-86 https://rodavigo.net/catalogos/GATES/Productos%20para%20motores%20industriales/GATES%2005%20Est%C3%A1ndares%20en%20la%20manguera.pdf

Fed Std 833P Items 240L Light Duty Shuttle Low-Floor.docx 8

3.5 TRANSMISSION

3.5.1 PERFORMANCE

-Transmission shall be automatic with a minimum of 5 forward speeds.

-Fluid shall be synthetic if available from OEM. Allison transmissions shall be equipped with TES-295 approved fluid. Transmission shall be labeled on its exterior to indicate the type of fluid installed.

3.5.2 SHIFT QUALITY & DRIVABILITY

-The overall drivability of the vehicle should not be negatively impacted by the transmission:

No bumps or vibrations should be felt while shifting

There should not be a significant delay when downshifting for more torque

The gears should not be audible during a shift

3.6 BRAKES

3.6.1 SERVICE BRAKES

-Chassis OEM Antilock Brake System shall be furnished.

3.7 AXLES

-The Gross Vehicle Weight Rating (GVWR) and individual axle Gross Axle Weight Rating (GAWR) shall not be exceeded when loaded with the specified number of passengers and baggage including the driver.

-GAWR calculation shall reflect maximum weight ratings as advertised by axle manufacturer and no higher rating of components shall be acceptable.

3.7.2 DRIVESHAFT (NOT APPLICAPLE TO FWD VEHICLES)

-Driveshaft protection shall comply with FMCSR 393.89

3.8 ELECTRICAL

3.8.1 ELECTRICAL SYSTEM

-All wiring provided by the FSAM shall be copper.

-All wiring shall have type SXL or GXL high temperature cross-linked polyethylene, or better, insulation.

-The use of multi conductor or ribbon cables are permitted provided they are not exposed to under hood or under vehicle temperatures/conditions.

-The wiring shall be permanently color coded or marked the entire length of the wire.

-Wiring shall be routed in conduit or high temperature looms with a rating of 300°F.

-When cables are supplied by a component manufacturer to interconnect system components, these cables need not be continuously color coded/identified. They shall be coded/identified at the termination or interconnection points.

-All added wiring shall be in accessible, enclosed, protected locations and kept at least 6" away from exhaust system components.

-All conduits, looms, and wiring shall be secured to the body or frame with insulated metal cable straps.

-All apertures on the vehicle shall be properly grommeted for passing wiring.-All items used for protecting or securing the wiring shall be appropriate for the specific application and be standard automotive, aircraft, marine, or electronic hardware.

-Cable ties shall not be used to support harnesses but may be used for bundling purposes.

-Electrical panels that are accessible to accidental contact shall have a protective cover, shield, etc. to prevent shorts that can result in injury, fire, or damage to the electrical system.

-All plastic materials shall be UV resistant and metal supports corrosion resistant:

P-clamps – Clamps shall be corrosion resistant with a neoprene, Viton, or silicone insulator.

https://www.fmcsa.dot.gov/regulations/title49/section/393.89

Fed Std 833P Items 240L Light Duty Shuttle Low-Floor.docx 9

Saddle-supports – Formed metal support with smooth radius edges designed to carry no less than twice the weight of the harness it supports.

Cable clamps – Die-formed, radius-edge, corrosion-resistant metal cable clamps and can only be used in bus interior or engine compartment in areas not subject to wetting by rain or road spray.

Plastic clamps can only be used in areas not exposed to heat that could exceed their working limits.

Button-cable ties – Saddle Mounts and button ties utilizing cable ties are an acceptable method of supporting chassis and body wiring and hoses. Cable ties shall be UV resistant and the support method used shall be rated for at least twice the weight of the component supported.

Nylon tie-wraps with push-wings – an acceptable method of securement in completely enclosed spaces (inside roof and walls). Method must be rated for at least twice the weight of wire supported.

-Electrical circuit board panels and components that are susceptible to accidental contact shall have a protective cover, shield, or enclosed/dedicated compartment to prevent accidental shorts that can result in injury, fire, or damage to the electrical system.

3.8.2 ALTERNATOR

-The maximum alternator RPM rating shall not be exceeded at the top governed engine RPM.

3.8.3 BATTERY

-All components within the battery compartment shall be protected from battery electrolyte and gas corrosion.

-Only battery cables shall be connected to batteries.

-Battery cables shall be routed through dedicated holes in battery box independent of each other and insulated from abrasion by grommets.

-No spliced battery cables permitted. Cables shall be one-piece, stranded conductor with protective covering (jacket) pigmented red to indicate positive and black to indicate negative and shall be run from the positive battery terminal of the leading battery directly to the starter solenoid.

3.8.4 AUXILIARY INTERIOR POWER RECEPTACLE

-Shall be 12-volt powered with 10-amp minimum supply located in the driver’s area.

Receptacle shape shall be similar to cigar lighter.

3.8.5 120-VOLT POWER

All powered components requiring alternating current (ac) shall operate on 120-volt (v), 60 Hz.

All electrical and heating materials shall be listed or labeled by a Nationally Recognized Testing Laboratory - i.e.: UL/CSA/ETL and shall be installed in accordance with both the manufacturers’ instructions and the National Electrical Code.

3.9 FUEL

3.9.1 FUEL SYSTEM

-Shall comply with FMCSR 393.65, 393.67, and 393.69

3.9.2 FUEL TANK(S)

-When the tank filler cap is located behind body skin, a hinged access door shall be furnished.

-Fuel fill(s) shall permit filling of tank(s) with only the nozzle end of the fuel handle.

-Fuel filler cap(s) shall be attached with a cable or chain to prevent loss.

-Fuel type shall be indicated on the body skin immediately next to fill cap or on the inside face of the fuel fill door.

The words “Ultra Low Sulfur Diesel” must be included when applicable.

Fed Std 833P Items 240L Light Duty Shuttle Low-Floor.docx 10

3.10 EXTERIOR

3.10.2 EXTERIOR MIRRORS

-Exterior mirrors shall be corrosion resistant stainless steel or composite plastic.

-Mirror mounting hardware shall be made of corrosion resistant materials.

-Motorized remote controlled and heated surfaces with controls located in driver’s area for flat mirrors.

Heat and position control switch(s) shall be “Marked to Indicate Function” and located in the driver’s area.

Heating function shall be automatically deactivated when the ignition switch is turned to the “OFF” position. A Pictogram can be used to identify mirror switches and functions.

3.10.3 LICENSE PLATES

-Front and rear license plate mounting provisions shall be furnished and comply with SAE J686.

3.10.4 OTHER PLATES AND DECALS

-Dealer identification decals and placards shall not be applied to vehicle exterior. Bus manufacturer decals are permitted so long as they do not interfere with other required or specified markings.

3.10.5 EXTERIOR PAINT

-The standard exterior color of buses shall be bright white unless otherwise specified by option in paragraph 3.25.

3.11 DOORS AND WINDOWS

3.11.1 PASSENGER DOORS

-Passenger door shall comply with ADA requirements.

-Shall comply with FMVSS 217

3.11.2 KEYS

-Exterior access panels to the engine compartment, battery compartment, doors, and storage compartments shall be keyed. Passenger entry and exit doors can be electronically or mechanically locked.

-If engine compartment is not keyed, it should only be able to be opened with a release inside the vehicle -Duplicate keys shall be furnished with each bus.

3.11.3 ENTRY RAMP

-Vehicle shall not use steps for passenger entry other than that from the ground to the landing inside the door.

-An electric or manual wheelchair ramp shall be provided as standard equipment to allow for a no step entry from the ground to the bus interior when deployed.

-Entry ramps shall comply with ADA guidelines and be surfaced with slip resistant and replaceable cover.

3.11.4 EMERGENCY EXITS

-Shall comply with FMCSR 393.61, 393.62, 393.63, 393.92.

3.11.5 PASSENGER WINDOWS

-Rattle proof and, when closed, waterproof and windproof.

-All windows that are used for emergency purposes shall be fitted with latching devices for emergency use.

3.11.5.1 TINTING

-Chassis manufacturer’s tinted windshield shall be furnished.

-Windows on the bus sides and in the rear door shall be tinted a neutral color, complementary to the bus exterior.

3.11.6 WINDSHIELD DEFROSTING

-Shall comply with FMVSS 571.103, FMCSR 393.79, and SAE J381

3.11.8 WINDSHIELD WIPING AND WASHING

-Shall comply with FMCSR 393.78, and SAE J198

Fed Std 833P Items 240L Light Duty Shuttle Low-Floor.docx 11

3.12 LIGHTS AND LIGHTING

3.12.1 EXTERIOR LIGHTING

-All exterior lights on the vehicle shall comply with ADA 1192.31, FMCSR 393.11, 393.19, 393.22, 393.23, 393.24, 393.25, 393.26, and SAE J589, and J910.

-The following exterior lighting shall be Light Emitting Diode (LED): rear tag, tail, stop, turn, clearance, and door area ground/curb illumination.

-Exclusions to LED requirement are wheel chair door area and ground lighting, headlamps, and other lights that cannot be replaced by a LED due to a design only available in incandescent or when multiple LED assemblies cannot be used to take the place of an incandescent fixture due to space limitations.

-LED lighting shall have a minimum 5-year warranty.

-All exterior lights shall be grounded with an insulated wire.

-The ground lead shall not be secured by the lamp fixture mounting screws or hardware.

-A terminal shall be attached to the wires by a simple mechanical crimp-type process that conforms to

SAE J163.

-Ground terminal lugs shall be solder plated, cadmium, tin or zinc plated.

-Ground terminals should be clustered and shall be accessible for servicing.

-A serrated paint-cutting terminal shall be utilized to make proper contact when used on painted surfaces.

-When two wire lights are not commercially available, then ground return connections may be made to vehicle structure, frame or engine using the ground-return system (one wire systems per SAE J1292).

-Lights and reflectors shall not be mounted on rub rails or vehicle bumpers unless recess protected.

-Reflectors must be a sticker type flexible material. The sticker must use cube corner elements to reflect light such as 3M Diamond Grade. Rigid plastic stick on or screw-on reflectors are not permitted.

-All lights or powered components mounted on hinged covers or doors shall have a flex loop secured at both ends to allow for normal opening of cover without damaging wires.

-Clearance lamps shall be low-profile design or body recessed to prevent damage from tree limbs. - Armor shields shall not be supplied to protect lighting unless supplied commercially as standard equipment.

-All buses shall be equipped with three-wire combination side marker/turn signal lamps.

-The lamp shall be positioned below the passenger windows, nominally center of body or forward to the rear of the passenger door and driver’s side window.

-A two wire LED marker lamp can be used in place of the three wire combination light so long as the illumination spread is nominally 270 degrees wide and the lamp is configured to operate as a marker continuously and then flash when driver requested, acting as a side turn signal.

-All exterior housings of lamps, switches, electronic devices, and fixtures shall be corrosion resistant and weatherproofed.

-Ground and step illumination shall be furnished to meet ADA guidelines. Lamps shall activate when the passenger entry or exit door is open.

3.12.2 INTERIOR LIGHTING

-Interior lighting shall include:

Minimum one row of SMI TRANSIT LF light emitting diode (LED) light fixtures installed center of aisle or integrated into overhead parcel racks when requested by option.

The fixtures shall extend as far to the rear of the bus and as far forward as possible in continuous joined assemblies.

A gap is permitted in the lamp assemblies when obstructions such as roof hatches prevent continuous lengths. Lens material shall be polycarbonate. Lens material shall not drip flaming onto seats if burned. Lens shall be sealed to inhibit incursion of dust and insects yet are easily removable for service. If threaded fasteners are used they must be held captive in the lens.

The light fixtures shall be powered when the passenger entry or exit door is opened. A manual override switch shall be provided to allow the driver to leave the interior lights on at all times so long as the ignition key is in the run or auxiliary position.

-White light emitting LED lamp assemblies can be used in place of the SMI fixtures with the number and brand of the fixtures at the discretion of the Contractor so long as the lamps meet the requirements of subparagraphs C and D. Lamps can be permanently sealed or contain replaceable elements.

-Minimum illumination values are below. All values must be measurable over the entire surface area.

Center aisle surface- no less than 2 foot candles per square foot.

Fed Std 833P Items 240L Light Duty Shuttle Low-Floor.docx 12

Entry and exit stepwell surfaces or ramp surface as applicable, no less than 2 foot candles per square foot.

All other interior passenger floor area surfaces, no less than 0.4 foot candles per square foot.

The foot candle values listed in subparagraph “e” shall be measured using a light meter placed on the floor surface.

A minimum of one LED dome light with no less than 4 foot candle output measured on top of the lower seat cushion shall be furnished over the driver’s area controlled independently of other interior lighting.

-The passenger entry and exit doorstep lighting must activate when the door is open

3.13 ELECTRONICS/AUDIO VISUAL

3.13.1 RADIO

-AM/FM with USB, Aux, or Bluetooth Input radio shall be furnished.

3.14 INTERIOR

3.14.1 AIR CONDITIONING SYSTEM

-Bus manufacturer’s highest output BTUH/HR system shall be furnished as standard.

-Independent dash air conditioning must be furnished as standard equipment.

-The system capacity must be calculated as follows:

1. Add together all evaporator capacities

2. Add together all condenser capacities

3. Add all compressor capacities.

-The BTUH/HR capacity stated must be the lowest added value. Dash air conditioning system must be added to the passenger compartment lowest added value and considered part of the total Air Conditioning Output listed in the Minimums for each Standard Item.-Evaporator fan speed control and thermostat setting shall be digital and located in driver area.

-Minimum diagnostic outputs and system protections shall include high pressure, low pressure.

-Automatic tensioning compressor drive belt(s).

-Added refrigerant compressors can be a swash plate type with not less than 163 cc / 10 CID displacement.

-The chassis manufacture’s dash defroster system shall not be tapped into as part of the passenger compartment cooling.-The passenger compartment air conditioning system, excluding the OEM dash unit, must have the system manufacturer’s recommended filter/drier and a refrigerant moisture indicating sight glass located to be readily viewable.

-All air shall pass through the evaporator filter system.

-Condensation drains shall be enough to evacuate all water accumulated in evaporator and prevent standing water.

-All system components subject to corrosion from moisture shall be aluminum, copper, stainless steel, galvanized, or epoxy coated.

-Condenser(s) can be skirt or roof mounted as standard.

-Evaporators can be free blow, ducted, or a combination to attain an even air flow and temperature environment.

-The compressor input RPM must not be exceeded at full engine RPM.

3.14.1.1 AIR CONDITIONING INSTALLATION

-System components shall not interfere with or adversely affect chassis OEM and bus body systems, components, function, reliability, and fit.

-Installation of the evaporator(s) and ancillary equipment inside the vehicle shall be mounted away from the head impact zone as specified in FMVSS 222.

-System shall be installed on the assembly line in accordance with the A/C manufacturer’s documented instructions.

Fed Std 833P Items 240L Light Duty Shuttle Low-Floor.docx 13

-All lines, hoses, cables, wires, and harnesses shall be rigidly supported at distances not greater than 20-inches. Cable ties or straps of any kind shall not be used to support any lines or hoses. UV-resistant cable ties are acceptable only for bundling.

-All line, hose, cable and wires shall pass-through grommeted holes.

-All body penetrations shall be sealed with an elastomeric sealing compound if grommeting alone cannot provide a tight seal against the entry of water, fumes, or dust into the passenger compartment.

-All mounting hardware shall be stainless steel or other corrosion resistant materials.

-No sheet metal screws shall be used in mounting equipment within contact of hoses.

-Condenser(s) shall be fit with a recirculation guard to aid fresh air flow across coils.

-Skirt mounted condensers shall be designed and located to prevent road debris and water splash from clogging or damaging the condenser.

-System charging and monitoring access ports shall be in areas where they will not be subject to damage from foreign objects while bus in motion. Ports shall be readily accessible without the need to remove components or permanently secured panels.

3.14.1.2 AIR CONDITIONING PERFORMANCE

-The BTUH/HR capacities shall be based upon the SAE individual component ratings including compressor, evaporator, condenser, and all ancillary refrigeration components.

-The evaporator shall be tested at 80 degrees F dry bulb/ 67-degree F wet bulb in 37 degrees F saturated evaporating refrigerant temperature versus air entering the evaporator.

-Condenser shall be tested at 95 degrees F with saturated refrigerant temperature as 45 degrees delta T.

-The following test must be used to validate air-conditioning performance:

The bus must be heat soaked to 100 degrees F for not less than two hours in a controlled environment prior to testing.

A relative humidity of 50% shall be maintained in the test chamber during testing.

The system must cool the interior of the bus from 100 degrees F to 70 degrees F in no more than 30 minutes with the engine at an elevated RPM and all standard components of the bus and climate control system installed during the test.

Interior temperature must be measured at not less than three points inside the bus along the centerline and located four feet above the floor.

The minimum three points of measure shall be (1) three feet above the center pint of the horizontal driver seat surface, (2) at the longitudinal midpoint of the body, and (3) three feet forward of the aisle end.

The temperature probes inside the bus must be within +/3 degrees F of the average temperature at the conclusion of the test.

3.14.2 HEATING

-Passenger compartment heating shall be provided using heat exchangers integrated into the air conditioning system or by radiant heaters located along the interior walls.

-All buses shall have a means of heating the air in the passenger door stepwell.

3.14.4 DRIVER’S AREA

-Driver’s area shall include as a minimum:

All switches and controls shall be marked with easily read identifiers

Ignition switch

Push button start is acceptable if the power supply to the switch is controlled by a keyed switch or electronic recognition.

Tilt or telescoping steering wheel/column

Engine coolant temperature overheat warning

Engine low oil pressure indication

Fuel level indicating gauge

Transmission selector

3.14.5 INTERIOR MIRROR

-Minimum of one non-glare type mirror shall be mounted inside the bus with a reflective surface area of not less than 80 square inches with rounded corners. Driver shall be able to view complete passenger compartment through interior mirror.

Fed Std 833P Items 240L Light Duty Shuttle Low-Floor.docx 14

3.15 FLOOR

3.15.1 FLOOR CONSTRUCTION

-Interior sub-floor shall be metal or composite, covered with not less than a minimum of 5/8-inch nominal thickness, marine grade plywood, with all ends sealed. Alternative synthetic materials may be acceptable.

-Waterproof composite sub floors shall be excluded from this requirement -Top surface must be not less than a grade B with bottom no worse than a grade C.

-All wood and wood product ends shall be sealed and securely fastened to the metal stringers prior to be covered with matting.

-All surfaces exposed to weather shall be coated with a waterproofing substance such as undercoating or epoxy surfaces.

-All floor fasteners shall be of corrosion resistant materials.

3.15.2 FLOOR COVERINGS

Floor covering shall be permanently bonded to the sub-floor and shall be impervious to temperature changes. Bonding or adhesive material shall be waterproof, including joints and seams, and shall be of the type recommended by the manufacturer of the floor covering material.

3.15.3 WHEEL-HOUSINGS

-Wheel-housings, which protrude into the passenger compartment, shall be covered with the same matting used under the seats or a material equal in durability as the flooring material. The wheelhouse shall be designed in shape and strength so it may be used as a footrest.

3.16 WALLS

-The standard interior walls shall be manufacturers standard complying with FMVSS 571.302.

3.18 SEATS

3.18.1 DRIVER’S SEAT

OEM Standard

3.18.2 PASSENGER SEATS

The required passenger count may be met by a combination of standard seating and single folding or flip and fold seats in the wheelchair locations. When using single folding seats in the wheelchair locations they may be doubles or triples at the bus manufacturer’s discretion.

-Each seat shall be equipped with a retractable safety belt with the retractor in a fixed position below the seat cushion. 3-point restraints shall be supplied if required based on bus GVWR.

-Seats mounted over wheel wells may be equipped with non-retractor type seat belts if it is not possible to install the required under seat retractors.

-Partial perimeter seating is acceptable where it is not practical to use forward facing seats due to passenger comfort issues.

-Seating and leg room requirements:

Hip-to-knee room: measured from the front of one seat back horizontally across the highest part of the seat cushion to the seat back or panel immediately in front shall be no less than 27-inches at all forward-facing seating positions.

Foot room: measured at the floor forward from a point vertically below the front of the seat cushion to an obstruction such as the driver barrier, shall be no less than 12 inches. Seats immediately behind the wheel housings may have foot room reduced, provided the wheelhouse is shaped so that it may be used as a footrest.

Fed Std 833P Items 240L Light Duty Shuttle Low-Floor.docx 15

3.19 SAFETY

3.19.1 BUMPERS

-Front and rear bumpers shall be manufacturer’s standard metal -Bumpers shall not contact body -Bumpers shall be painted, e-coated, or anodized on all sides prior to installation.

-Back surface of bumper can be epoxy primed in the absence of top coating if not visible during normal operation.

3.19.2 STANCHIONS, BARRIERS, AND GRAB RAILS

-The installation of the driver’s barrier shall not interfere with the full reward motion of the driver’s seat.

-ADA compliant handrails are required at the front and rear of the passenger entrance shall be arranged to safely assist passengers entering or leaving the bus -All stanchions and grab rails shall be ADA compliant stainless steel, epoxy coated, or padded injection-foam covered tubing. If padded tubing is used, the foam must meet all FMVSS requirements and be vandal resistant transit quality material. Opaque barriers shall be covered with the same material as the wall covering unless formed from injection molded plastic.

-All stanchions, barriers and grab rails shall be attached to tapping plates in walls, floor and ceiling if no structural members are available.

3.19.3 EMERGENCY EQUIPMENT

-Shall comply with FMCSR 393.95 -Fire extinguisher mounted convenient to the driver. -The fire extinguisher shall have an Underwriter’s Laboratory rating of 2A 10 B:C or greater, shall be a minimum 5 pounds, shall have a hose, shall include a metal safety pin and wire, and shall conform to type I or type II, class 2, size 5 of A-A-393.

-The fire extinguisher shall permit visual determination of charge.

-Minimum of 10-unit type first-aid kit shall be furnished.

3.20 SUSPENSION

3.20.1 GROSS VEHICLE WEIGHT RATINGS

-Vehicle GVWR’s shall be the chassis manufacturer’s published ratings.

-Component and vehicular ratings shall not be increased to meet the requirements of this Specification.

-When published ratings are not available, verification of rating shall be made available upon request by the Government.

3.20.2 SUSPENSION

- If the vehicle has a kneeling function, it must include transmission shift interlock, exterior warning lamp, and audible alarm.

-Safety interlocks to prevent vehicle movement with deflated air springs, unless the bus is designed to be capable of being driven in the kneeled position.

3.21 TIRES AND WHEELS

3.21.1 TIRES

-Shall comply with FMVSS 571.119 and 571.120 -Tubeless, steel belted radial tires with highway tread and a minimum speed rating of 75 mph.

3.21.2 WHEELS

-Wheel/Tire size and ply rating shall be the same for all wheels/tires.

-Shall be manufacturer’s standard color

Fed Std 833P Items 240L Light Duty Shuttle Low-Floor.docx 16

3.22 MISCELLANEOUS

3.22.1 OPERATION MANUALS & 1398 FORM

-Operation manuals shall be furnished with each bus.

-The Contractor shall fully complete and affix a GSA Form 1398 to the vehicle in the Driver's area. The exact location shall be agreed upon during the First Production Vehicle Inspection by both the Contractor and GSA Quality Assurance Branch Representative assigned to the facility

3.22.2 SERVICING AND ADJUSTING

-Prior to acceptance of the vehicle by the Government, the Contractor shall inspect, service and adjust each vehicle for operational use in accordance with an approved manufacturer’s prescribed pre-delivery servicing form.

- The in-transit mileage accumulation on vehicles driven from the assembly plant to the receiving location shall be recorded and the start of warranty coverage adjusted to begin once the bus reaches the destination address.

-The areas to be inspected and adjusted, if necessary, shall include as a minimum:

All fluids and fuel tank(s) shall be full.

Alignment of headlights.

All engine adjustments.

Electrical and brake systems.

Filling and charging of batteries.

Alignment of front wheels.

Inflation of all tires.

Complete lubrication of body, chassis, engine and running gear with grade of lubricants recommended for the ambient air temperature at the delivery point.

Servicing of the cooling system with a solution of ethylene glycol type antifreeze and water in equal parts by volume.

Servicing of the windshield washer reservoir with water and appropriate additives.

3.26 GENERAL WORKMANSHIP REJECTION STANDARDS

The following shall be reason for rejection:

Rough, sharp or unfinished edges, burrs, seams, corners, joints, cracks, and dents. Sharp corners and edges shall be either rounded or padded to prevent injury to personnel.

Interior cleanliness: vehicle interior should not contain trash or manufacturing debris (spare screws, bolts, rivets, etc.).

Panels, non-uniform with edges that are not radiused, beveled, etc.

Final stage manufacturer’s paint shall be free of dirt and have minimal runs, sags, orange peel, "fish eyes", blisters, bubbles, chips, scratches, cracks, gouges, over-spray, peeling, chemical stains, water spots, and any other imperfection or lack of complete coverage.

Body panels or components that are uneven, unsealed, or contain cracks, dents or have voids.

Misalignment of body fasteners, glass, viewing panels, light housings, items with large or uneven gaps or spacing and doors, body panels, and hinged panels.

Improper body design or interface with the chassis that could cause injury during normal use or maintenance.

Improperly fabricated, routed, supported or secured hoses, wires, wiring harnesses and mechanical controls.

Loose, vibrating, abrading body parts, components or subassemblies.

Interference of chassis components, body parts, doors, etc.

Leaks of any gas or fluid lines, (AC, coolant, oil, etc.)

Sagging, non-form fitting upholstery or padding.

Incomplete or incorrect application of rust proofing/undercoating.

Inappropriate or incorrect use of hardware, fasteners, components, or methods of construction.

Fed Std 833P Items 240L Light Duty Shuttle Low-Floor.docx 17

Incomplete or improper welding, riveting. Welded, bolted and riveted construction utilized shall be in accordance with the highest standards of industry using certified welders.

Improper body design or interface with the chassis substructure that could cause injury during normal use or maintenance, and which fail to provide access to perform routine or mandatory repairs or maintenance on vehicle electrical and mechanical systems. In addition, the improper combination of options by their combination and installation are inherently incompatible with regard to function or safety.

Visual deformities and equipment malfunctions.

Lack of uniformity and symmetry where applicable.

Unsealed appurtenances or other body components, gaskets, etc.

All exterior surfaces shall be smooth and free of wrinkles and dents.

In addition, any deviation from the requirements or any other item, whether stipulated herein, that affects form, fit, function, durability, reliability, safety, performance or appearance shall be cause for rejection.

3.27 IDENTIFICATION OF VEHICLES

The Contractor must show the applicable GSA Purchase Order number on the carrier's freight bill or other document used in the delivery of vehicles awarded f.o.b. destination under this solicitation. This information is essential to the consignee for identification purposes. Vehicles will not be accepted by the Government without this identifying number

3.28 CERTIFICATE OF ORIGIN OR BILL OF SALE

The manufacturer’s Certificate of Origin or Bill of Sale for each vehicle procured shall be provided to the purchasing agency. The front of the document shall show the applicable RPN number shown on the Motor Vehicle Delivery Order. Non-OEM resellers must reassign the document to the purchasing agency listed in the Consignee Mailing Address shown on the Motor Vehicle Delivery Order. The document shall be forwarded to the Consignee Mailing Address shown on the Vehicle Delivery Order prior to shipment.

Vehicle title/registration and safety/emission tests are the responsibility of the requisitioning agency.

3.29 WARRANTY REQUIREMENTS

Warranties in this document are in addition to any statutory remedies or warranties imposed on the Contractor. Consistent with this requirement, the Contractor shall warrant and guarantee to the Government each complete bus vehicle and specific subsystems and components according to the following provisions. The Contractor shall be fully responsible for warranty administration for any and all warranty periods. The Contractor shall have an authorized service representative assigned to assist the Government warranty administration.

3.29.1 COMPLETE BUS VEHICLE

The Contractor shall warranty and guarantee the bus for the same time and mileage durations as publicly published and furnished to non-Government buyers. The Contractor shall be responsible for all defects, parts failure or malfunction due to design, construction or installation errors, defective workmanship, and missing or incorrect parts. The warranty period shall begin upon delivery and acceptance at the final delivery point and exclusive of accumulated drive away mileage. The Contractor shall be fully responsible to ensure the bus is delivered free of defects and in ready of use condition at the time of delivery. If the vehicle is found to have deficiencies the Contractor will resolve those prior to final delivery.

3.29.2 SUBSYSTEM AND COMPONENTS

If the Contractor receives from any supplier or subcontractor additional warranty coverage on the whole or any component of the vehicle, in the form of time and/or mileage including any pro rata arrangements, or the Contractor generally extends to his commercial customers a greater or extended warranty coverage, including anti-corrosion, powertrain, or emission, the Government shall receive corresponding warranty benefits if warranted by their manufacturer for a period longer than that required by the contract.

Fed Std 833P Items 240L Light Duty Shuttle Low-Floor.docx 18

3.30 EXCEPTIONS TO WARRANTY

The warranty shall not apply to scheduled maintenance items and items furnished by the Government, except insofar as such equipment may be damaged by the failure of a part or component for which the Contractor is responsible.

3.31 DETECTION OF DEFECTS

If the Government detects a defect within the warranty periods, it shall promptly notify the Contractor's representative. Additionally, warranty repairs shall begin no more than 3 business days or 5 calendar days after vehicle has been presented for repairs. If the repairs have not been approved by the Contractor within that period of 10 days, the Government shall consider the contractor, and it's authorized service center in breach of the contract, and the government may exercise all remedies including, but not limited to, seeking a third party to repair the vehicles and demand reimbursement for all related expenses from the contractor that sold the vehicle to the government.

3.32 SCOPE OF WARRANTY REPAIRS

-The offeror must disclose all restrictions placed upon the Government to comply with the warranty coverage.

-The offeror must operate a factory authorized parts and service center (to include 3rd party factory approve cross service agreement subcontractors) within a 100 mile geographic radius of the final destination delivery location to support the commercial warranty. The contractor is required to disclose whether or not they can meet this requirement within five (5) working days of the receipt of the requisition/order to the contracting officer/contracting specialist.

-The offeror must disclose whether they offer towing and transport services at no cost to the Government during the factory warranty period. If there is an additional charge for this service, the offeror must indicate the per mile transport charge.

-All factory installed components that have a commercial warranty that exceeds the Federal minimum "bumper to bumper"…