O. RELOC Distribution Box Primary (Basis of Design).pdf

DBP

One Lithonia Way Conyers, GA 30012 Phone: 800-705-SERV (7378) techsupportreloc@acuitybrands.com www.relocwiring.com © 2008-2022 Acuity Brands Lighting, Inc. All rights reserved. Rev. 11/08/22

FEATURES & SPECIFICATIONS

INTENDED USE

The Primary Distribution Box (DBP) is used to bring multiple circuits from the electrical panel into an area of the building where they can be further distributed to utilization equipment.

The Primary Distribution Box serves as a modular junction box to allow a transition from oversized conductors used in the RELOC Mainrun Cable (RMC) to the RELOC modular wiring system. Avail- able in two sizes, the DBP can be used in an open ceiling, above a hung ceiling, and below a raised floor, including low-profile raised floors.

CONSTRUCTION

Keying prevents accidental mating of circuits with different voltages. Available with up to twelve RELOC ports; Up to three circuits per RELOC port. Two sizes: 9” x 9” (up to 6 RELOC ports) and 12” x 12” (up to 12 RELOC ports). Low-profile DBP – 1.7” height.

ELECTRICAL

Rated for 20A branch circuit use.

Isolated ground and two hots and two neutrals wiring available. All internal wiring uses 12AWG stranded copper THHN (90°C).

INSTALLATION

Labeled to identify panel and circuit available at each port.

Integrated RMC provides oversized conductors to minimize voltage drop. RMC labeled to identify assigned circuit breaker in panel.

Optionally available with labeled terminal blocks ready for field-wiring to homerun wiring.

SYSTEM FEATURES

Compatible with RELOC systems 820, Quick-Flex and One Pass. The DBP is normally provided with an integrated RMC attached and all ports and con- ductors labeled to show circuit as-signments. Alternatively, the DBP can be provided without a RMC, allowing the circuits to be field-wired to the DPB using any approved wiring method.

LISTINGS

Suitable for use in other environmental air areas used for NEC 300.22 (c). UL/CUL-Listed.

BUY AMERICAN ACT

This product is assembled in the USA and meets the Buy America(n) government procurement requirements under FAR, DFARS and DOT regulations.

Please refer to www.acuitybrands.com/resources/buy-american for additional information.

WARRANTY

1-year limited warranty. Complete warranty terms located at:

www.acuitybrands.com/support/customer-support/terms-and-conditions

Note: Actual performance may differ as a result of end-user environment and application.

Specifications subject to change without notice.

Catalog Number

Notes Type

Distribution Box Primary

DBP

WIRING SOLUTIONS

Series Voltage Output connection1 Options

DBP Distribution box primary S5DBP SIMPLY5 Distribution box primary10

120 120V 208 208V6

220 220V6

240 240V6

277 277V 347 347V 480 480V6

_CD Sytem 820 circuit distributor2,5

_OC ONEPASS converter2,5,7

_QC QUICK-FLEX converter3,4,8,9

(blank) No option 2N Two hots and neutrals IGW Isolated ground wire PB Pull box11

LP Low-profile box

ORDERING INFORMATION For shortest lead times configure product using bolded options. Example: DBP 120 4CD

Notes

1. Minimum output ports available is 2. Maximum output ports available is 12. Specify number of ports per box in blank.

2. CD and OC - three circuits available for 120v,277v and 347v. Three phase circuit or two circuits available for 208v, 220v, 240v and 480v.

3. QC - two circuits available for 120v, 277v and 347v.

4. QC - not available in 208, 220v, 240v and 480v.

5. CD and OC - 120v, 277v and 347v two circuits available with 2N option only.

6. 208v, 220v, 240v and 480v - not available with IGW and 2N options.

7. OC - not available with IGW option.

8. QC - 120v one circuit available with IGW option.

9. QC - 2N option not available.

10. S5DBP - 2N and IGW option not available.

11. Maximum number of output ports available with PB option is 8.

mailto:techsupportreloc%40acuitybrands.com?subject= https://reloc.acuitybrands.com/

One Lithonia Way Conyers, GA 30012 Phone: 800-705-SERV (7378) techsupportreloc@acuitybrands.com www.relocwiring.com © 2008-2022 Acuity Brands Lighting, Inc. All rights reserved. Rev. 11/08/22

DBP Distribution Box Primary

SPECIFICATIONS

Enclosure

• Size: 9"x9" or 12"x12"

• Height: 1.7" or 3"

• Construction: one-piece, riveted

• Integral leg: 0.25" high with 0.27" mounting holes

• Thickness: 16-gauge galvanized steel

• Lid: drip-resistant design

Connectors

• Input: 1.7” maximum to fit 1-1/4” trade size FMC/MC connector

• Output: CD, ONEPASS® OC or QUICK-FLEX® QC

Output connectors

• Current rating: 20A

• Contact type: Socket

• Contact termination type: crimp

• Contact material: tin-plated copper

• Insulating material: PC, PC/PEI or PBT

Grounding

• Grounding lug type: pass-through

• Grounding lug size: 6AWG - 14 AWG input ground conductor

• Connection: grounding lug fastened to enclosure internally

• Connectors: all input and output connectors grounded to enclosure

External bonding

• External grounding lug for under-floor applications

• Bonding lug type: pass-through

• Bonding lug size: 6AWG - 14 AWG ground conductor

Labeling • Output connectors: port number, panel number, circuit numbers

One Lithonia Way Conyers, GA 30012 Phone: 800-705-SERV (7378) techsupportreloc@acuitybrands.com www.relocwiring.com © 2008-2022 Acuity Brands Lighting, Inc. All rights reserved. Rev. 11/08/22

DBP Distribution Box Primary

SYSTEM VIEW

System View designs are for illustrative purposes only.

One Lithonia Way Conyers, GA 30012 Phone: 800-705-SERV (7378) techsupportreloc@acuitybrands.com www.relocwiring.com © 2008-2022 Acuity Brands Lighting, Inc. All rights reserved. Rev. 11/08/22

DBP Distribution Box Primary

DIMENSIONS