I. RELOC OnePass Convertor - OC Series (Basis of Design).pdf

OC_OSFC_OSC2

One Lithonia Way Conyers, GA 30012 Phone: 800-705-SERV (7378) techsupportreloc@acuitybrands.com www.relocwiring.com © 2017-2022 Acuity Brands Lighting, Inc. All rights reserved. Rev. 11/08/22

Catalog Number

Notes Type

FEATURES & SPECIFICATIONS

INTENDED USE

The OnePass converters (OC), starter fixture cable (OSFC), and starter cable 2 port (OSC2) provides the interface between hardwiring and RELOC at the homerun location. The OC is a single female port available with 6 inch wire leads standard or with armored cable. The OSFC attaches directly into the access plate or through any 1/2" trade-size knockout. The OSC2 is a splitter and starter extender cable in one easy to-use component.

ELECTRICAL

• Fits a standard 1/2" trade size knockout.

• 6" leads prestripped 5/8" for ease of wiring.

• Available in varying lengths to suit most common fixture spacing requirements.

• Auto-latching springs prevent accidental disengagement.

• The OC with cable length and OSFC available with green armor standard for easy identification in healthcare facilities (HCF option).

• Non-plenum rated OC2 plastic housing.

• The OC, OSS and OSC2 with EXT opiton enables them to be installed in hot and cold applications (-40° to +90°C).

• Type of insulation for EXT option is based on NEC Table 310.104(A)

SYSTEM FEATURES

• Pin and socket contacts.

• Color-coded labels for quick voltage identification.

• Dust Cover available for unused ports: RDC3 METAL DUST COVER CSA/UL J50 (available job pack of 50 only)

CONTROLS-ENABLED WIRING OPTIONS

• 0-24V integrated single-circuit or 0-10V low voltage controls applications: select C12S option.

• Sensor Switch®, nLight®, LC&D XPoint™ fixture level controls applications: select CAT5_

(length) option.

LISTINGS

• C-UL-US listed for indoor, dry, and accessible locations.

• Meets or exceed all the requirements of UL183 and NEC (NFPA70) Article 604 for manufactured wiring systems.

• C12S option meets NEC requirements for separation of Class 2 and Class 3 circuits from Class

1 circuits by a barrier as defined by Article 725.136(B).

• Meets NEC requirements for redundant ground paths for patient care areas in healthcare facilities (HCF option).

• Canadian Patent No. 2,845,603 (Class l, Class ll)

BUY AMERICAN ACT

This product is assembled in the USA and meets the Buy America(n) government procurement requirements under FAR, DFARS and DOT regulations.

Please refer to www.acuitybrands.com/resources/buy-american for additional information.

WARRANTY

5-year limited warranty. This is the only warranty provided and no other statements in this specification sheet create any warranty of any kind. All other express and implied warranties are disclaimed. Complete warranty terms located at: www.acuitybrands.com/support/ warranty/terms-and-conditions Note: Actual performance may differ as a result of end-user environment and application.

Specifications subject to change without notice.

OnePass® Converter/Starter Cables

OC, OSFC, OSC2

OC

Converter

OSFC

Starter Fixture Cable

OSC2

Starter Cable 2 Port mailto:techsupportreloc%40acuitybrands.com?subject= http://www.relocwiring.com https://www.acuitybrands.com/resources/buy-american http://www.acuitybrands.com/support/warranty/terms-and-conditions http://www.acuitybrands.com/support/warranty/terms-and-conditions

OnePass® Converter/Starter Cables

One Lithonia Way Conyers, GA 30012 Phone: 800-705-SERV (7378) techsupportreloc@acuitybrands.com www.relocwiring.com © 2017-2022 Acuity Brands Lighting, Inc. All rights reserved. Rev. 11/08/22

Series Voltage Conductors Length Controls Wiring Finish Options

OSC2 120 120V

208 208V 240 240V 277 277V 347 347V 480 480V

10/2G Three 10 AWG conductors, including one 10 AWG ground

10/3G Four 10 AWG conduc-tors, including one 10 AWG ground

10/4G Five 10 AWG conduc-tors, including one 10 AWG ground

12/2G Three 12 AWG conductors, including one 12 AWG ground

12/3G Four 12 AWG conduc-tors, including one 12 AWG ground

12/4G Five 12 AWG conduc-tors, including one 12 AWG ground

01 ft up to 50 ft (blank) Not required C12S Integrated CI,CII rated line voltage and signal wires ‡

CAT5_ Preterminated and tested CAT5 cable attached, specify length ‡

(blank) Not required RD Red ‡

(blank) Not required 2N Two circuit, two neutral ‡ EXT Extreme temperature rating conductors ‡

ORDERING INFORMATION For shortest lead times configure product using bolded options. Example: OSC2 277 10/4G 01

Series Voltage Conductors Length Controls Wiring Finish Options

OC 120 120V

208 208V 240 240V 277 277V 347 347V 480 480V

12/2G Three 12 AWG conductors, including one 12 AWG ground

12/3G Four 12AWG conductors, including one 12 AWG ground

12/4G Five 12 AWG conductors, including one 12 AWG ground

(blank) 6" wire leads 01 ft up to 50 ft

(blank) Not required C12S Integrated CI,CII rated line voltage and signal wires ‡

(blank) Not required RD Red ‡

(blank) Not required 2N Two circuit, two neutral ‡ EXT Extreme temperature rating conductors ‡ HCF Meets healthcare facility requirements ‡

ORDERING INFORMATION For shortest lead times configure product using bolded options. Example: OC 277 12/4G 01 RD

‡ Option Value Ordering Restrictions & Notes

Option value Restriction 2N Available with 12/4G and 120 or 277 or 347 only.

C12S Available with 12/2G only.

EXT Available with 12/2G and 12/3G only. Required for EXTREME hot and cold temperature applications (-40° to 90°C).

HCF Available with 12/4G only. Not available with C12S or 6" wire leads.

RD Available in lengths up to 35 foot only. Not available with 6" wire leads.

‡ Option Value Ordering Restrictions & Notes

Option value Restriction 2N Available with 10/4G or 12/4G and 120 or 277 or 347 only.

C12S Available with 12/2G only.

CAT5_ See spec sheet RCAT5 for details. When used with OCS, OCU or OD fixture drop, CAT5 length must include the length of the OSC2 and the length of drop for the fixture plus 2FT.

EXT Available with 10/2G or 10/3G or 12/2G or 12/3G only. Required for EXTREME hot and cold temperature applications.(-40° to 90°C).

RD Available in lengths up to 35 foot only.

mailto:techsupportreloc%40acuitybrands.com?subject= http://www.relocwiring.com https://www.acuitybrands.com/products/detail/148375/reloc/rcat5-modular-wiring/onepassr-rcat5-modular-wiring

OnePass® Converter/Starter Cables

One Lithonia Way Conyers, GA 30012 Phone: 800-705-SERV (7378) techsupportreloc@acuitybrands.com www.relocwiring.com © 2017-2022 Acuity Brands Lighting, Inc. All rights reserved. Rev. 11/08/22

Series Voltage Conductors Length Connector Type Controls Wiring Options CAT5 Cable

OSFC 120 120V

208 208V 240 240V 277 277V 347 347V 480 480V

12/2G Three 12 AWG conductors, including one 12 AWG ground

12/3G Four 12AWG conductors, including one 12 AWG ground

12/4G Five 12 AWG conductors, including one 12 AWG ground

01 ft up to 50 ft (blank) Not required RRL RELOC®-ready luminaires ‡

(blank) Not required C12S Integrated

CI,CII rated line voltage and signal wires ‡

(blank) Not required G Ground wire ‡ 2N Two circuit, two neutral ‡ HCF Meets healthcare facility requirements ‡

(blank) Not required CAT5_ Preterminated and tested CAT5 cable attached, specify length ‡

ORDERING INFORMATION For shortest lead times configure product using bolded options. Example: OSFC 277 12/2G 05

‡ Option Value Ordering Restrictions & Notes

Option value Restriction 2N Available with 12/4G and 120 or 277 or 347 only.

C12S Available with 12/2G only.

CAT5_ See spec sheet RCAT5 for details. CAT5 length must be 2 foot longer than OSFC length.

G G option required for use in Canada. Required for C12S, HCF, and RRL Option.

HCF Available with 12/4G only. Not available with C12S or CAT5_.

RRL For use with fixtures. Fixture must have RRL and wiring instruction installed to use this option. See fixture spec sheet for details and availability. See RRL spec sheet sheet for connector details.

mailto:techsupportreloc%40acuitybrands.com?subject= http://www.relocwiring.com https://www.acuitybrands.com/products/detail/148375/reloc/rcat5-modular-wiring/onepassr-rcat5-modular-wiring https://www.acuitybrands.com/products/detail/248102/reloc/rrl/reloc-ready-connector

OnePass® Converter/Starter Cables

One Lithonia Way Conyers, GA 30012 Phone: 800-705-SERV (7378) techsupportreloc@acuitybrands.com www.relocwiring.com © 2017-2022 Acuity Brands Lighting, Inc. All rights reserved. Rev. 11/08/22

DIMENSIONS

Dimensions are shown in inches (millimeters)

OC – Converter

A – 18-gauge, zinc-plated, CRS cover B – UL-recognized connector body C – Tin-plated, brass contacts D – 6" leads prestripped 5/8" E – Threaded nipple with locknut for easy installation in 1/2" trade-size K.O.

A – Die-cast zinc with zinc-plated CRS cover B – UL recognized connector body C – Tin-plated brass contacts D – Length option required. MC Cable standard. HCF MC, C12S MC optional. IGW option standard with FMC.

NOTES

• One, two or three hot conductors in 120V and 277V as required.

• Rated for 20-amp capacity.

• Prefabricated circuit distributor carrying No. 12 AWG copper conductors rated at 600V, 90°C thermoplastic insulation and fully rated solid bare grounding conductor.

Standard Construction Armored Cable Construction

2-3/16 (55.6)

2-3/8 (60.3)

9/16 (14.3)

BA

CD

E

2-3/16 (55.6)

9/16 (14.3)

3-3/8 (87.5)

B A

C D

OC2OC

OC2OCS/OCU

OCS/OCU

SYSTEM VIEW

System View designs are for illustrative purposes only.

mailto:techsupportreloc%40acuitybrands.com?subject=

OnePass® Converter/Starter Cables

One Lithonia Way Conyers, GA 30012 Phone: 800-705-SERV (7378) techsupportreloc@acuitybrands.com www.relocwiring.com © 2017-2022 Acuity Brands Lighting, Inc. All rights reserved. Rev. 11/08/22

A – Injection-molded, high-impact polymeric compound enclosure

B – Tin-plated, brass contacts C – MC Cable standard. C12S MC optional.

DIMENSIONS

Dimensions are shown in inches (millimeters)

4-1/2 (114.3)

1-1/8 (28.7)

2-1/4 (57.2)

B

A

C

SYSTEM VIEW

System View designs are for illustrative purposes only.

OSC2

OC2OCS/OCU

OCS/OCU

OSC2 – Starter Cable 2 Port

OnePass® Converter/Starter Cables

One Lithonia Way Conyers, GA 30012 Phone: 800-705-SERV (7378) techsupportreloc@acuitybrands.com www.relocwiring.com © 2017-2022 Acuity Brands Lighting, Inc. All rights reserved. Rev. 11/08/22

OSFC – Starter Fixture Cable

DIMENSIONS

Dimensions are shown in inches (millimeters)

A – UL-recognized connector body B – Die-cast zinc with zinc-plated CRS cover C – Tin-plated, brass contacts D – Cast snap-in fitting fits 1.2" trade-size K.O. and provides grounding E – No. 18 AWG solid copper wires rated at 600V, 90°C thermoplastic insulation with stripped leads F – MC Cable standard. FMC, HCF MC, C12S MC optional

NOTES

• One, two or three hot conductors in 120V and 277V as required.

• Rated for 20-amp capacity.

• Prefabricated standard selector cable carrying No. 12 AWG copper conductors. 600V, 90°C thermoplastic insulation and fully rated bare grounding conductor.

• Standard selector cable provides auto-grounding to fixture unless specified otherwise.

B

F

C D

A

2-1/4 (58)

2-3/16 (55.6)

7/16 (11.1)

9/16 (14.3)

1-1/4 (31.8)

3-3/8 (87.5)

3-1/4 (82.6)

E

E

SYSTEM VIEW

System View designs are for illustrative purposes only.

Connection above the wall

MC CABLE

(BY OTHERS)

MC CABLE

(BY OTHERS)

MC CABLE

(BY OTHERS)

Connection inside the wall

MC CABLE

(BY OTHERS)

MC CABLE

(BY OTHERS)

MC CABLE

(BY OTHERS)

OFSC

OFSCOFSC

OFSC

OFC

OFC

OFC

OFC

OnePass® Converter/Starter Cables

One Lithonia Way Conyers, GA 30012 Phone: 800-705-SERV (7378) techsupportreloc@acuitybrands.com www.relocwiring.com © 2017-2022 Acuity Brands Lighting, Inc. All rights reserved. Rev. 11/08/22

ONEPASS® CONVERTER/STARTER CABLES WIRE COLOR CHART

120V, 277V, 347V Standard Wire Colors

Position 1 2 3 4 5 Conductor Ground Hot# 1 Hot# 2 Hot# 3 Neutral #1

120V & 347V Bare or Green Black Red Blue White 277V Bare or Green Brown Orange Yellow Gray

208V, 240V, 480V Standard Wire Colors Position 1 2 3 4 5 Conductor Ground Hot# 1 Hot# 2 Hot# 3 Hot #4

208V & 240V Bare or Green Black Red Blue Violet 480V Bare or Green Brown Orange Yellow Violet

120V, 277V, 347V Two Circuit, Two Neutral (2N option) Position 1 2 3 4 5 Conductor Ground Hot# 1 Hot# 2 Neutral #2 Neutral #1

120V & 347V Bare or Green Black Red Gray White 277V Bare or Green Brown Orange White Gray

120V, 277V, 347V Class I, Class II (C12S option) Position 1 2 3 4 5 Conductor Hot #1 Neutral #1 Ground Data #1 Data #2

120V & 347V Black White Bare or Green Violet Pink (or Gray) 277V Brown Gray Bare or Green Violet Pink (or Gray)

208V & 240V Brown Orange Bare or Green Violet Pink (or Gray) 480V Brown Orange Bare or Green Violet Pink (or Gray)

120V Isolated Ground Wire (IGW option) Position 1 2 3 4 5 Conductor Ground Hot# 1 Hot# 2 IGW Neutral #1

120V Bare or Green Black Red Green w/Yellow stripe White mailto:techsupportreloc%40acuitybrands.com?subject= http://www.relocwiring.com