NORTH_ARFF_KITCHEN_DRAWINGS-BID.pdf

PDF 3 MB Posted Jul 16, 2026

Attached to: North ARFF Station 2 Kitchen Remodel
Solicitation number: 26-043-ITB
Issued by: Bell County, Kentucky

About this file

Written by GovTribe AI · Jul 23, 2026

This document set consists of architectural and engineering drawings for the North ARFF Kitchen Remodel project at Cincinnati/Northern Kentucky International Airport, prepared by Emboss Design, P.S.C. for the Kenton County Airport Board. The project involves a comprehensive kitchen renovation at the North ARFF Fire Station located at 81 Clay Drive, Hebron, Kentucky, including demolition of existing cabinetry, countertops, and finishes; installation of new kitchen cabinets with solid surface countertops and backsplash; replacement of ceiling systems with 2x2 vinyl-faced suspended panels in the kitchen and 2x4 suspended acoustical panels in adjacent areas; new lighting controls and fixtures; new aluminum storefront door with tempered glass; and relocation of existing equipment including refrigerators, ice machine, and coffee dispenser. The drawings are dated for bidding and permitting as of June 30, 2026, with a pre-bid meeting and site visit scheduled for Thursday, July 30, 2026 at 10:00 am. Questions are due by 11:59 pm on August 10, 2026, with answers posted by August 13, 2026, and bids due by 2:00 pm on August 20, 2026.

The project scope includes contractor-furnished and contractor-installed work, owner-furnished items (range, refrigerators, microwave), and coordination with multiple trades including electrical, mechanical, plumbing, and fire protection systems. Electrical work includes new branch circuiting, lighting controls with occupancy sensors and dimming capability, temporary kitchen power provisions via a new 100-amp panel, and reconnection of existing equipment through the Ansul fire suppression system. The temporary kitchen requires a contactor system to disable power during emergency calls, with three cord reel drops for refrigerator power. Fire protection modifications maintain 100% wet pipe sprinkler coverage with heads removed, saved, and reinstalled. Plumbing work includes a new stainless steel farmer sink with supporting piping. The design accommodates existing structural elements including radiators, exhaust hoods, and fire extinguisher cabinets. Procurement coordination is required for cabinet field measurements and sizing to accommodate existing equipment and plumbing connections.

View the file

Other files

File	Type	Posted
North_ARFF_Station_2_Kitchen_Remodel_(Addendum_#2_Revision).pdf	PDF	Aug 12, 2026
26-043-ITB_N_ARFF_Station_2_Kitchen_Drawings_-ADDENDUM_2.pdf	PDF	Aug 12, 2026
North_ARFF_Station_2_Kitchen_Remodel_(Addendum_#1_Revision).pdf	PDF	Jul 23, 2026
North_ARFF_Station_2_Kitchen_Remodel.pdf	PDF	Jul 23, 2026
26-043-ITB_N_ARFF_Station_2_Kitchen_Remodel_-_Exhibit_B_-_Contract_&_Bonds.pdf	PDF	Jul 21, 2026
26-043-ITB_N_ARFF_Station_2_Kitchen_Remodel_-_Ad.pdf	PDF	Jul 20, 2026
26-043-ITB_North_ARFF_Station_2_Kitchen_Remodel_-_Drawings.pdf	PDF	Jul 16, 2026
26-043-ITB_N_ARFF_Station_2_Kitchen_Remodel_-_Exhibit_A_-_Proposal_Forms.pdf	PDF	Jul 16, 2026
26-043-ITB_North_ARFF_Station_2_Kitchen_Remodel_-_Technical_Specs.pdf	PDF	Jul 16, 2026
EEO_Certification.docx	DOCX document	Jul 16, 2026
NORTH_ARFF_KITCHEN_SPECS_7.13.26.pdf	PDF	Jul 16, 2026
Affirmative_Action_Certification.docx	DOCX document	Jul 16, 2026
Business_Case_-_North_ARFF_Kitchen_Rehabilitation.pdf	PDF	Jul 16, 2026
Non_Debarment_or_Suspension_Certification.docx	DOCX document	Jul 16, 2026
Disclosure_of_Lobbying_Activities_Certification.docx	DOCX document	Jul 16, 2026
NORTH_ARFF_KITCHEN_ESTIMATE_OF_PROBABLE_COST_2026.06.29.pdf	PDF	Jul 16, 2026
NonSegregated_Facilities_Certification.docx	DOCX document	Jul 16, 2026
Certification_of_Offeror-Bidder_Regarding_Tax_Delinquency_and_Felony_Convictions.docx	DOCX document	Jul 16, 2026
N._ARFF_KITCHEN_BID_TAB.xlsx	XLSX spreadsheet	Jul 16, 2026
Buy_American_Certification-Construction_Projects.docx	DOCX document	Jul 16, 2026
Buy_American_Certification-Equipment-Building_Projects.docx	DOCX document	Jul 16, 2026

Show all 21

On GovTribe

Work with this file

Download the original file
Contacts named in this file
Similar government files
Ask GovTribe AI about this file

Try for free Login

Text version

The file's text, extracted by GovTribe without its formatting.

OVERALL FIRST FLOOR PLAN

A100

A1 FIRST FLOOR PLAN

SCALE: 1/8" =1'-0"

15141312 161110987654321

D O

C U M

T, A N

D T

H E

S A N

D D

N S

C O

R A

D H

N , A

S A N

I N

R U M

O F

A L

R V

E, I S

O F

N , P

.S .C

A N

D I S

N O

B E

D I N

E DATE DESCRIPTIONNO.

15141312 161110987654321

W H

O R I N

P A R T

R A

N Y

R O

C T, W

H O

U T

W R

A U

O R

O N

O F

N , P

.S .C

C O

H T

-2

N , P

.S .C

Pr oj ec ts \P r2

N or th

A R

K itc he n R em od el \0

6- D ra w in gs

\6 .0

3- C

2026-021

4/20/26 30% REVIEW SET

Cincinnati/Northern Kentucky International Airport

NORTH ARFF

FIRE STATION

Kitchen Remodel

5/15/26 60% REVIEW SET

CONSTRUCTION NOTES

6/1/26 90% REVIEW SET

6/30/26 BIDDING & PERMIT

AutoCAD SHX Text

DINING

AutoCAD SHX Text

KITCHEN

AutoCAD SHX Text

STORAGE

AutoCAD SHX Text

DORM

AutoCAD SHX Text

COMMUNICATIONS

AutoCAD SHX Text

SHIFT OFFICE

AutoCAD SHX Text

DORM

AutoCAD SHX Text

DORM

AutoCAD SHX Text

DORM

AutoCAD SHX Text

CORRIDOR

AutoCAD SHX Text

DORM

AutoCAD SHX Text

STORAGE

AutoCAD SHX Text 109B

AutoCAD SHX Text

VESTIBULE

AutoCAD SHX Text

CORRIDOR

AutoCAD SHX Text

STOR.

AutoCAD SHX Text 143A

AutoCAD SHX Text

STAIR

AutoCAD SHX Text

CORRIDOR

AutoCAD SHX Text

CLOSET

AutoCAD SHX Text 123A

AutoCAD SHX Text

CORRIDOR

AutoCAD SHX Text

SHOWER

AutoCAD SHX Text

MEN

AutoCAD SHX Text

WOMEN

AutoCAD SHX Text

CORRIDOR

AutoCAD SHX Text

DORM

AutoCAD SHX Text

CORRIDOR

AutoCAD SHX Text

SHOWER

AutoCAD SHX Text

SHOWER

AutoCAD SHX Text

SHOWER

AutoCAD SHX Text

DORM

AutoCAD SHX Text

DORM

AutoCAD SHX Text

DORM

AutoCAD SHX Text

DORM

AutoCAD SHX Text

DORM

AutoCAD SHX Text

DORM

AutoCAD SHX Text

LAUNDRY

AutoCAD SHX Text

SCBA

AutoCAD SHX Text

ELEVATOR

AutoCAD SHX Text

STOR.

AutoCAD SHX Text

EMS

AutoCAD SHX Text

CORRIDOR

AutoCAD SHX Text

STOR.

AutoCAD SHX Text 138A

AutoCAD SHX Text

STAIR

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

CONFERENCE

AutoCAD SHX Text

WORK ROOM

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

COMP

AutoCAD SHX Text

VESTIBULE

AutoCAD SHX Text

CORRIDOR

AutoCAD SHX Text

LOBBY

AutoCAD SHX Text

APPARATUS BAY

AutoCAD SHX Text

FOAM

AutoCAD SHX Text

AutoCAD SHX Text T.O.G.

AutoCAD SHX Text

SHOP

AutoCAD SHX Text

STAIR

AutoCAD SHX Text

MEN

AutoCAD SHX Text 102A

AutoCAD SHX Text

WOMEN

AutoCAD SHX Text 102B

AutoCAD SHX Text

RANGE BY OWNER

AutoCAD SHX Text

ICE MACHINE BY OWNER

AutoCAD SHX Text

EX. EYE WASH

AutoCAD SHX Text

REFRIGERATORS BY OWNER

AutoCAD SHX Text

3'-0" TABLE W/ MICROWAVES BY OWNER

AutoCAD SHX Text A101

AutoCAD SHX Text A6

AutoCAD SHX Text 10A

AutoCAD SHX Text 01 EXISTING ITEMS 1A. 1B. EXISTING VENDING MACHINES TO REMAIN. REMOVE/REINSTALL AS REQ'D TO COMPLETE WORK 1C. EXISTING REFRIGERATORS. RELOCATE TO NEW LOCATION 1D. EXISTING ICE MACHINE. RELOCATE TO NEW LOCATION 1E. EXISTING COFFEE DISPENSER. RELOCATE TO NEW LOCATION 1F. EXISTING FIRE EXTINGUISHER CABINET TO REMAIN 1G. EXISTING RADIATOR TO REMAIN 1H. EXISTING EXHAUST TO REMAIN 1J. EXISTING TABLE AND CHAIRS WILL BE REMOVED AND REINSTALLED BY OWNER 1K. EXISTING WALL MOUNTED TV TO REMAIN 1L. EXISTING DISHWASHER. REMOVE/REINSTALL AS REQ'D TO COMPLETE WORK 1M. RELOCATE CUP DISPENSER AS DIRECTED BY OWNER 1N. REMOVE/REINSTALL FIRE EXTINGUISHER AS REQ'D TO COMPLETE WORK 1P. REMOVE/REINSTALL SIGN AS REQ'D TO COMPLETE WORK 1Q. REMOVE/REINSTALL MISC. WALL MOUNTED PICTURES, SIGNS, ETC. AS REQ'D TO COMPLETE WORK 02 DEMOLITION DEMOLITION 2A. DEMO WALL 2B. DEMO BASE/WALL CABINETS, COUNTER, AND ASSOCIATED SINK 2C. DEMO CERAMIC TILE AND BASE 2D. DEMO SOAP AND PAPER TOWEL DISPENSERS 2E. RELOCATE ANSUL CONTROLS. SEE MEP DRAWINGS FOR ADDL INFO. 2F. DEMO WINDOW BLINDS. NEW BLINDS WILL BE BY OWNER 2G. DEMO CARPET 2H. DEMO RANGE 2J. REMOVE DOOR - FRAME TO REMAIN 2K. DEMO SUSPENDED ACOUSTICAL PANEL CEILING 08 OPENINGS OPENINGS 8A. NEW ALUMINUM STOREFRONT DOOR (3'-0"x7-8"± FIELD VERIFY) INEXISTING FRAME WITH TEMPERED, TINTED, INSULATING LOW-E GLASS. TEMPERED, TINTED, INSULATING LOW-E GLASS. FINISH TO MATCH EXISTING. PROVIDE HINGES, PUSH BAR/PULL, LATCH SET, THRESHOLD, SWEEP, WEATHERSTRIPPING, AND ELECTRIC STRIKE TO MATCH EXISTING. RECONNECT TO EXISTING MATRIX ACCESS CONTROL SYSTEM 10 SPECIALTIES SPECIALTIES 10A. 4'-0" HIGH CORNER GUARD 12 FURNISHING 12A. NEW RANGE - SUPPLIED BY OWNER, INSTALLED BY CONTRACTOR 12B. NEW REFRIGERATOR - SUPPLIED BY OWNER, INSTALLED BY CONTRACTOR

AutoCAD SHX Text 906 Monmouth Street, AutoCAD SHX Text Newport, KY 41071

AutoCAD SHX Text EmbossDesign.com

AutoCAD SHX Text (859)431-8612

AutoCAD SHX Text X

DEMOLITION PLAN

ENLARGED FLOOR PLAN

A101

A1 PARTIAL DEMOLITION PLAN

SCALE: 1/8" =1'-0"

15141312 161110987654321

D O

C U M

T, A N

D T

H E

S A N

D D

N S

C O

R A

D H

N , A

S A N

I N

R U M

O F

A L

R V

E, I S

O F

N , P

.S .C

A N

D I S

N O

B E

D I N

E DATE DESCRIPTIONNO.

15141312 161110987654321

W H

O R I N

P A R T

R A

N Y

R O

C T, W

H O

U T

W R

A U

O R

O N

O F

N , P

.S .C

C O

H T

-2

N , P

.S .C

Pr oj ec ts \P r2

N or th

A R

K itc he n R em od el \0

6- D ra w in gs

\6 .0

3- C

2026-021

4/20/26 30% REVIEW SET

Cincinnati/Northern Kentucky International Airport

NORTH ARFF

FIRE STATION

Kitchen Remodel

A6 ENLARGED FLOOR PLAN

SCALE: 1/4" =1'-0"

5/15/26 60% REVIEW SET

J6 PARTIAL CEILING DEMOLITION PLAN

SCALE: 1/8" =1'-0"

CONSTRUCTION NOTES

ROOM FINISH SCHEDULE

6/1/26 90% REVIEW SET

6/30/26 BIDDING & PERMIT

AutoCAD SHX Text

VENDING

AutoCAD SHX Text

VENDING

AutoCAD SHX Text

ICE

AutoCAD SHX Text

COFFEE

AutoCAD SHX Text

RELOCATED

AutoCAD SHX Text

DINING

AutoCAD SHX Text

KITCHEN

AutoCAD SHX Text

STORAGE

AutoCAD SHX Text

COMMUNICATIONS

AutoCAD SHX Text

SHIFT OFFICE

AutoCAD SHX Text

VESTIBULE

AutoCAD SHX Text

CORRIDOR

AutoCAD SHX Text

AutoCAD SHX Text A102

AutoCAD SHX Text J11

AutoCAD SHX Text A7

AutoCAD SHX Text J7

AutoCAD SHX Text A102

AutoCAD SHX Text G7

AutoCAD SHX Text A102

AutoCAD SHX Text G7

AutoCAD SHX Text

OPP. HAND

AutoCAD SHX Text

EXISTING

AutoCAD SHX Text

EXISTING

AutoCAD SHX Text

DISPENSER

AutoCAD SHX Text

EX. FEC

AutoCAD SHX Text

EX. FE

AutoCAD SHX Text 9'-4"

AutoCAD SHX Text 4'-0"

AutoCAD SHX Text 10A

AutoCAD SHX Text 12A

AutoCAD SHX Text 12B

AutoCAD SHX Text 10A

AutoCAD SHX Text 8A

AutoCAD SHX Text

DINING

AutoCAD SHX Text

KITCHEN

AutoCAD SHX Text

STORAGE

AutoCAD SHX Text

DORM

AutoCAD SHX Text

COMMUNICATIONS

AutoCAD SHX Text

SHIFT OFFICE

AutoCAD SHX Text

DORM

AutoCAD SHX Text

DORM

AutoCAD SHX Text

DORM

AutoCAD SHX Text

CORRIDOR

AutoCAD SHX Text

DORM

AutoCAD SHX Text

STORAGE

AutoCAD SHX Text 109B

AutoCAD SHX Text

VESTIBULE

AutoCAD SHX Text

CORRIDOR

AutoCAD SHX Text

STOR.

AutoCAD SHX Text 143A

AutoCAD SHX Text

STAIR

AutoCAD SHX Text

CORRIDOR

AutoCAD SHX Text

CLOSET

AutoCAD SHX Text 123A

AutoCAD SHX Text

CORRIDOR

AutoCAD SHX Text

SHOWER

AutoCAD SHX Text

MEN

AutoCAD SHX Text

WOMEN

AutoCAD SHX Text

CORRIDOR

AutoCAD SHX Text

DORM

AutoCAD SHX Text

CORRIDOR

AutoCAD SHX Text

SHOWER

AutoCAD SHX Text

SHOWER

AutoCAD SHX Text

SHOWER

AutoCAD SHX Text

DORM

AutoCAD SHX Text

DORM

AutoCAD SHX Text

DORM

AutoCAD SHX Text

DORM

AutoCAD SHX Text

DORM

AutoCAD SHX Text

DORM

AutoCAD SHX Text

LAUNDRY

AutoCAD SHX Text

SCBA

AutoCAD SHX Text

ELEVATOR

AutoCAD SHX Text

STOR.

AutoCAD SHX Text

EMS

AutoCAD SHX Text

CORRIDOR

AutoCAD SHX Text

STOR.

AutoCAD SHX Text 138A

AutoCAD SHX Text

STAIR

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

CONFERENCE

AutoCAD SHX Text

WORK ROOM

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

COMP

AutoCAD SHX Text

VESTIBULE

AutoCAD SHX Text

CORRIDOR

AutoCAD SHX Text

LOBBY

AutoCAD SHX Text

MEN

AutoCAD SHX Text 102A

AutoCAD SHX Text

WOMEN

AutoCAD SHX Text 102B

AutoCAD SHX Text 2A

AutoCAD SHX Text 1C

AutoCAD SHX Text 2A

AutoCAD SHX Text 1F

AutoCAD SHX Text 1G

AutoCAD SHX Text 2E

AutoCAD SHX Text 2F

AutoCAD SHX Text 1J

AutoCAD SHX Text 1H

AutoCAD SHX Text 1K

AutoCAD SHX Text 1L

AutoCAD SHX Text 2G

AutoCAD SHX Text 2H

AutoCAD SHX Text 1B

AutoCAD SHX Text 1D

AutoCAD SHX Text 1E

AutoCAD SHX Text 1M

AutoCAD SHX Text 1N

AutoCAD SHX Text 1P

AutoCAD SHX Text 2B

AutoCAD SHX Text 2C

AutoCAD SHX Text 1Q

AutoCAD SHX Text 1K

AutoCAD SHX Text 2C

AutoCAD SHX Text 2D

AutoCAD SHX Text

EX. CARPET TO REMAIN

AutoCAD SHX Text 2J

AutoCAD SHX Text 2K

AutoCAD SHX Text

DEMO GYP. BD. SOFFIT

AutoCAD SHX Text

DEMO SUSP. ACT. CLG.

AutoCAD SHX Text

DEMO SUSP. ACT. CLG.

AutoCAD SHX Text

EX. GYP. BD. SOFFIT TO REMAIN

AutoCAD SHX Text

EX. GYP. BD. CLG. TO REMAIN

AutoCAD SHX Text 906 Monmouth Street, AutoCAD SHX Text Newport, KY 41071

AutoCAD SHX Text EmbossDesign.com

AutoCAD SHX Text (859)431-8612

AutoCAD SHX Text X

VESTIBULE 100 FLOOR: WALK-OFF CPT TILE & CERAMIC TILE BORDER (MATCH WALK-OFF CPT TILE & CERAMIC TILE BORDER (MATCH EXISTING BORDER PATTERN) BASE: 6" CERAMIC TILE 6" CERAMIC TILE WALLS: PAINT PAINT CEILING: 2x4 SUSPENDED ACOUSTICAL PANEL CEILING 2x4 SUSPENDED ACOUSTICAL PANEL CEILING CORRIDOR 109 FLOOR: CERAMIC TILE CERAMIC TILE BASE: 6" CERAMIC TILE 6" CERAMIC TILE WALLS: PAINT PAINT CEILING: 2x4 SUSPENDED ACOUSTICAL PANEL CEILING 2x4 SUSPENDED ACOUSTICAL PANEL CEILING VESTIBULE 131 FLOOR: CERAMIC TILE CERAMIC TILE BASE: 6" CERAMIC TILE 6" CERAMIC TILE WALLS: PAINT PAINT CEILING: 2x4 SUSPENDED ACOUSTICAL PANEL CEILING 2x4 SUSPENDED ACOUSTICAL PANEL CEILING CORRIDOR 132 FLOOR: WALK-OFF CPT TILE & CERAMIC TILE BORDER (MATCH WALK-OFF CPT TILE & CERAMIC TILE BORDER (MATCH EXISTING BORDER PATTERN) BASE: 6" CERAMIC TILE 6" CERAMIC TILE WALLS: PAINT PAINT CEILING: 2x4 SUSPENDED ACOUSTICAL PANEL CEILING 2x4 SUSPENDED ACOUSTICAL PANEL CEILING KITCHEN 134 FLOOR: CERAMIC TILE CERAMIC TILE BASE: 6" CERAMIC TILE 6" CERAMIC TILE WALLS: PAINT PAINT CEILING: 2x2 SUSPENDED VINYL FACED CEILING PANELS 2x2 SUSPENDED VINYL FACED CEILING PANELS DINING 135 FLOOR: CERAMIC TILE CERAMIC TILE BASE: 6" CERAMIC TILE 6" CERAMIC TILE WALLS: PAINT PAINT CEILING: 2x4 SUSPENDED ACOUSTICAL PANELS2x4 SUSPENDED ACOUSTICAL PANELS

REFLECTED CEILING PLAN

A102

A1 REFLECTED CEILING PLAN

SCALE: 1/4" =1'-0"

15141312 161110987654321

D O

C U M

T, A N

D T

H E

S A N

D D

N S

C O

R A

D H

N , A

S A N

I N

R U M

O F

A L

R V

E, I S

O F

N , P

.S .C

A N

D I S

N O

B E

D I N

E DATE DESCRIPTIONNO.

15141312 161110987654321

W H

O R I N

P A R T

R A

N Y

R O

C T, W

H O

U T

W R

A U

O R

O N

O F

N , P

.S .C

C O

H T

-2

N , P

.S .C

Pr oj ec ts \P r2

N or th

A R

K itc he n R em od el \0

6- D ra w in gs

\6 .0

3- C

2026-021

4/20/26 30% REVIEW SET

Cincinnati/Northern Kentucky International Airport

NORTH ARFF

FIRE STATION

Kitchen Remodel

A7 ELEVATION

SCALE: 3/8" =1'-0"

J7 ELEVATION

SCALE: 3/8" =1'-0"

J11 ELEVATION

SCALE: 3/8" =1'-0"

G7 ELEVATION

SCALE: 3/8" =1'-0"

5/15/26 60% REVIEW SET

6/1/26 90% REVIEW SET

6/30/26 BIDDING & PERMIT

AutoCAD SHX Text

LOCKABLE FULL HEIGHT PLASTIC LAMINATE CABINET W/ ADJ. SHELVING

AutoCAD SHX Text 7'-0"

AutoCAD SHX Text W2430

AutoCAD SHX Text B24

AutoCAD SHX Text 7'-0"

AutoCAD SHX Text

EXIST.

AutoCAD SHX Text

COFFEE

AutoCAD SHX Text

DISP.

AutoCAD SHX Text

REF

AutoCAD SHX Text

REF

AutoCAD SHX Text

REF

AutoCAD SHX Text

MICRO

AutoCAD SHX Text

MICRO

AutoCAD SHX Text W3342

AutoCAD SHX Text

EX. SOFFIT

AutoCAD SHX Text 1'-6"

AutoCAD SHX Text B30

AutoCAD SHX Text B33

AutoCAD SHX Text W3024

AutoCAD SHX Text 2'-0"

AutoCAD SHX Text

FIELD MEASURE PRIOR TO ORDERING CABINETS

AutoCAD SHX Text 3'-0"

AutoCAD SHX Text

SOLID SURFACE COUNTER W/ 4' BACKSPLASH

AutoCAD SHX Text

FILLER

AutoCAD SHX Text 9'-4"

AutoCAD SHX Text

P. LAM. MICROWAVE SHELF

AutoCAD SHX Text

EXISTING

AutoCAD SHX Text

SB36

AutoCAD SHX Text

DISHWASHER

AutoCAD SHX Text

EXISTING

AutoCAD SHX Text

DISHWASHER

AutoCAD SHX Text

CABINET TO ACCOMMODATE "FARMER" SINK. COORD. SIZE W/ PLUMBING CONTR.

AutoCAD SHX Text

S.S. "FARMER" SINK

AutoCAD SHX Text

B18 BLIND CORNER W/

AutoCAD SHX Text

SOAP DISPENSER SUPPLIED BY OWNER FOR G.C. INSTALL

AutoCAD SHX Text W2442

AutoCAD SHX Text W3618

AutoCAD SHX Text W2442

AutoCAD SHX Text W3042

AutoCAD SHX Text 3'-0"

AutoCAD SHX Text

SOLID SURFACE COUNTER

AutoCAD SHX Text

REV-A-SHELF BLIND CORNER

AutoCAD SHX Text 7'-11"/8'-0"±

AutoCAD SHX Text

OPTIMIZER HARDWARE

AutoCAD SHX Text

CERAMIC TILE

AutoCAD SHX Text

REINSTALL

AutoCAD SHX Text

REINSTALL

AutoCAD SHX Text

EXISTING EXHAUST HOOD

AutoCAD SHX Text W3642

AutoCAD SHX Text B30

AutoCAD SHX Text W2442

AutoCAD SHX Text

NEW RANGE

AutoCAD SHX Text 3'-0"

AutoCAD SHX Text

SOLID SURFACE COUNTER

AutoCAD SHX Text

EX. S.S. WALL PANEL TO REMAIN - CLEAN

AutoCAD SHX Text

CERAMIC TILE

AutoCAD SHX Text B30

AutoCAD SHX Text

DB30

AutoCAD SHX Text

PLASTIC LAMINATE CABINET W/ ADJ. SHELVING

AutoCAD SHX Text

STAINLESS STEEL COUNTER @ ISLAND ONLY

AutoCAD SHX Text 3'-0"

AutoCAD SHX Text B30

AutoCAD SHX Text

BASE BID: PAINT EXISTING GYP. BD. CLG.

AutoCAD SHX Text 2x4 SUSPENDED ACOUSTICAL PANEL CEILING ARMSTRONG #933

AutoCAD SHX Text GRID LOCATION & HEIGHT TO MATCH EXISTING TO MAINTAIN EXISTING SPRINKLER & HVAC DEVICE LOCATIONS

AutoCAD SHX Text

EX. EXHAUST HOOD

AutoCAD SHX Text

NEW GYP. BD. SOFFIT @ 8'-0"±TO ALIGN W/ EX. SOFFITS TO REMAIN - PAINTPAINT

AutoCAD SHX Text 2x2 VINYL FACED SUSPENDED GYPSUM PANEL CEILING

AutoCAD SHX Text GRID LOCATION & HEIGHT TO MATCH EXISTING TO MAINTAIN EXISTING SPRINKLER & HVAC DEVICE LOCATIONS

AutoCAD SHX Text

EX. GYP. BD. SOFFIT TO REMAIN - PAINT

AutoCAD SHX Text GRID LOCATION & HEIGHT TO MATCH EXISTING TO MAINTAIN EXISTING SPRINKLER & HVAC DEVICE LOCATIONS

AutoCAD SHX Text

ALTERNATE 1: PAINT EXISTING GYPSUM BOARD CEILING

AutoCAD SHX Text ALTERNATE 1: 2x4 SUSPENDED ACOUSTICAL PANEL CEILING ARMSTRONG #933

AutoCAD SHX Text

ALTERNATE 1: PAINT EXISTING GYP. BD. CLG.

AutoCAD SHX Text

NO CEILING WORK

AutoCAD SHX Text 906 Monmouth Street, AutoCAD SHX Text Newport, KY 41071

AutoCAD SHX Text EmbossDesign.com

(859)431-8612

UON

CFOI

OFOI

CFCI

OFCI

DESCRIPTION

POWER SUPPLY/CONTROL FOR AUDIO/VISUAL DEVICES

SLASH THROUGH ANY DEVICE INDICATES MOUNTING

ABOVE COUNTERTOP 2" ABOVE BACKSPLASH, OR AT

48" WHERE NO COUNTER IS PRESENT

FILLED CENTER BAR INDICATES INTEGRAL GROUND

FAULT PROTECTION (GFCI)

CONTRACTOR FURNISHED OWNER INSTALLED

CONTRACTOR FURNISHED CONTRACTOR INSTALLED

OWNER FURNISHED OWNER INSTALLED

OWNER FURNISHED CONTRACTOR INSTALLED

PHOTO-ELECTRIC SMOKE DETECTOR

MAIN CONTROL PANEL CENTRAL PROCESSING

UNIT (CPU)

LIGHT SWITCH:GENERAL PURPOSE

6'-6'' TO

TOP

UNLESS OTHERWISE NOTED

INDICATES EMERGENCY POWER

46"

ABBREVIATIONS

POWER OUTLETS

DUPLEX RECEPTACLE

QUADRUPLEX RECEPTACLE

JUNCTION BOX, CEILING OR WALL

OCCUPANCY OR VACANCY SENSOR, CEILING MOUNT

LOW VOLTAGE SWITCH ON OFF WITH ZONES

CLG

46"

1'-6"

CLG

M O

U N

G H

H T

(T O

C E

N T

E R

O F

B O

D R

A W

Y M

B O

ADDRESSABLE RELAY MODULE R

CONDUIT CONCEALED IN WALLS OR IN CEILING

SPACE: ARROW(S) INDICATE(S) HOME RUN & #

OF CIRCUITS: HASHMARKS INDICATE # OF

CONDUCTORS. DASHED LINE INDICATES

CONDUIT BELOW FLOOR.

PANELBOARD, SURFACE OR FLUSH MOUNTED,

HATCHING INDICATES EMERGENCY

EQUIPMENT TAG, REFER TO EQUIPMENT SCHEDULE

AS NOTED

MISCELLANEOUS

DISCONNECT SWITCH

TRANSFORMER

TAGGED NOTE

CONDUIT PATH

5'-0"

6'-6'' TO TOP

C A

B L

G C

O N

D U

C T

O R

O F

O I

C A

B L

C O

N D

U C

T O

R S

F C

C O

N D

O U

G H

-I N

F O

M U

S E

D O

N P

R O

J E

C T

D E

E S

F C

D E

E S

F C

SYSTEM D

E S

F O

SYSTEM

RESPONSIBILITY

MATRIX

SYSTEM RESPONSIBILITY GENERAL NOTES:

A. CMTA IS NOT RESPONSIBILE FOR ASSIGNING SCOPE(S) OR WORK. THE INTENT OF

CONTRACTOR IN THIS MATRIX IS TO SEPERATE OWNER PROVIDED ITEMS FROM THE

GENERAL CONTRACTOR / CONSTRUCTION MANAGER. THE GC OR CM SHALL BE

RESPONSIBLE FOR A COMPLETE SCOPE OF WORK.

B. REFER TO VENDOR DRAWINGS FOR COMPLETE SCOPE OF WORK RELATING TO

VENDOR-FURNISHED EQUIPMENT. ALL WORK INDICATED ON VENDOR DRAWINGS SHALL

BE INCLUDED BY THE CONTRACTOR.

C. REFER TO ARCHITECTURAL DOOR HARDWARE SPECIFICATIONS FOR ACCESS CONTROL

DEVICE SPECIFICATIONS AND FURTHER REQUIREMENTS.

D. PROVIDE BACKBOXES AND CONDUIT WITH PULL-STRINGS FOR ALL SYSTEMS.

CONTRACTOR SHALL VERIFY BACKBOX SIZES, CONDUIT, ETC. AND EXACT

INSTALLATION LOCATIONS/REQUIREMENTS WITH SUCCESSFUL VENDORS OF ALL

SYSTEMS PRIOR TO CONSTRUCTION.

E. AT ALL SYSTEMS EQUIPMENT CABINET/TERMINAL BOARD LOCATIONS, CONTRACTOR

SHALL PROVIDE SIZE AND NUMBER OF CONDUIT STUB-OUTS TO CABLE PATHS AS

REQUIRED BY SYSTEM VENDORS, TERMINATE CONDUITS AT CABINETS/ON

BACKBOARDS AS REQUIRED. COORDINATE EXACT REQUIREMENTS WITH APPROPRIATE

VENDORS PRIOR TO CONSTRUCTION.

F. REFER TO SPECIFICATIONS FOR REQUIREMENTS APPLICABLE TO ALL SYSTEMS

INCLUDING CABLING, CABLE MANAGEMENT, INSTALLATION, GROUNDING, TESTING,

LABELING, ETC.

G. WHERE INDICATED AS CFCI, THE CONTRACTOR SHALL PROVIDE THE SYSTEM

COMPLETE, INCLUDING ALL ROUGH-INS, CABLING, DEVICES, POWER, ETC. THE

CONTRACTOR SHALL CONTACT THE LISTED VENDOR FOR PRICING PRIOR TO BID. ALL

SYSTEMS SHALL MATCH EXISTING FACILITY STANDARDS AND BE FULLY COMPATIBLE

WITH ANY EXISTING SYSTEMS. ALL SYSTEM VENDORS SHALL COORDINATE EXACT

SYSTEM REQUIREMENTS WITH OWNER PRIOR TO BID. NEW COMPONENTS SHALL BE

INTERCONNECTED WITH EXISTING SYSTEMS WHERE POSSIBLE. ALL NEW SYSTEM

DESIGNS AND PROGRAMMING SHALL BE COORDINATED WITH THE OWNER PRIOR TO

ORDERING. ALL PROGRAMMING SHALL BE INCLUDED AS REQUIRED BY THE OWNER.

PROVIDE 4 HOURS OF TRAINING FOR EACH SYSTEM.

SWITCHES

FIRE ALARM

E,EMINDICATES EMERGENCY POWER

NAC

FACP

AS SHOWNSOLID BOTTOM CABLE TRAY, SIZE AS NOTED

EQUIP-1

GROUND

NEUTRAL

PHASE

, J

#D/#V

INTERMEDIATE DISTRIBUTION FRAME - REFERENCE

DATA SYSTEM SCHEMATICS AND DETAILS FOR

ADDITIONAL REQUIREMENTS

MAIN DISTRIBUTION FRAME - REFERENCE DATA

SYSTEM SCHEMATICS AND DETAILS FOR ADDITIONAL

REQUIREMENTS

WIRELESS ACCESS POINT WITH PROVISIONS FOR (1

DATA OUTLET FOR ANTENNA. PROVIDE A COMPLETE

DATA OUTLET WITH FACEPLATE ABOVE CEILING,

MOUNTED AT AN ACCESSIBLE HEIGHT NO MORE THAN

24" ABOVE CEILING. AT EACH OUTLET, PROVIDE A 20'

COIL OF CABLE AHEAD OF THE OUTLET FOR

ADJUSTMENT OF FINAL OUTLET LOCATION. THE

CONTRACTOR SHALL COORDINATE EXACT LOCATIONS

WITH THE OWNER AND ADJUST OUTLET LOCATIONS AT

SUBSTANTIAL COMPLETION TO ACCOMMODATE

OWNER'S WAP LOCATIONS. WAP'S ARE OWNER-

FURNISHED, OWNER-INSTALLED

WAP

DATA OUTLET : NUMBER BESIDE OUTLET

INDICATES NUMBER OF DATA JACKS

VOICE OUTLET : NUMBER BESIDE OUTLET

INDICATES NUMBER OF VOICE JACKS

COMBINATION OUTLET : NUMBER BESIDE OUTLET

INDICATES NUMBER OF DATA/VOICE JACKS

DATA / VOICE

1'-6"

MDF

IDF

GROUND BUS BAR ON INSULATED STANDOFFS 2'-0''

DESCRIPTION M

U N

G H

H T

(T O

C E

N T

E R

O F

B O

D R

A W

B O

DESCRIPTION M

U N

G H

H T

(T O

C E

N T

E R

O F

B O

D R

A W

B O

DESCRIPTION

LV#S,

W H

DEVICE

WALL SWITCHES

DEVICE COLOR

MATRIX

RECEPTACLE (NORMAL)

DEVICE COLOR GENERAL NOTES:

A. DEVICE PLATE TO MATCH DEVICE UNLESS NOTED OTHERWISE.

B. NOT ALL DEVICES MAYBE USED THAT ARE SHOWN.

C. IF DEVICE COLOR NOT DEFINED REFER TO SPECIFICATIONS.

DESCRIPTION

R Y

R E

O R

A N

G E

B L

U E

Y E

L L O

C U

S T

O M

S T

L E

S S

S T

E E

LEGEND

INDICATES SELECTED COLOR

INDICATES COLOR NOT AVAILABLE

INDICATES COLOR NOT SELECTED

LEGEND

INDICATES SELECTED SYSTEM

INDICATES NOT AVAILALBE

INDICATES NOT SELECTED

C O

N D

O U

G H

-I N

F C

C O

N D

O U

G H

-I N

F C

C A

B L

C O

N D

U C

T O

R S

F C

P R

O G

R A

M M

E T

U P

F O

P R

O G

R A

M M

E T

U P

F C

P R

O G

R A

M M

E T

U P

F C

CONDUIT PATH UNDERNEATH RAISED FLOOR

FIRE ALARM

PUSHBUTTON STATION 46"

RECEPTACLE (UPS)

RECEPTACLE (ISOLATED GROUND)

T E

R M

N S

F C

T E

R M

N S

F C

T E

R M

N S

F O

LOW VOLTAGE SINGLE ZONE DIMMING SWITCH AS NOTED S M

S LV1-DLOW VOLTAGE SWITCH SINGLE ZONE DIMMER SWITCH 46"

SECURITY CCTV VIDEO SURVEILLANCE

REMOTE DOOR RELEASE PUSH-BUTTON 8" ACT RR

ELECTRICAL CORD REAL TO CEILING

S y c a m o re S t, S u it e

C in c in n a ti

O H

2026-021

Cincinnati/Northern Kentucky International Airport

NORTH ARFF

FIRE STATION

Kitchen Remodel

D O

C U M

T, A N

D T

H E

S A N

D D

N S

C O

R A

D H

N , A

S A N

I N

R U M

O F

A L

R V

E, I S

O F

N , P

.S .C

A N

D I S

N O

B E

D I N

W H

O R I N

P A R T

R A

N Y

R O

C T, W

H O

U T

W R

A U

O R

O N

O F

B O

N , P

.S .C

C O

H T

-2

M B O

N , P

.S .C

E DATE DESCRIPTIONNO.

P ro je c ts

\P r2

-0

N o rt h A

R F

F K it c h e n R e m o d e l\ -D ra w in g s \6

.0 -C

15141312 161110987654321

6/30/26 BIDDING & PERMIT

906 Monmouth Street, Newport, KY 41071

EmbossDesign.com

(859)431-8612

E 0 0 0

E L E C T R I C A L L E G E N D

ELECTRICAL GENERAL NOTES:

A. EACH CONTRACTOR, PROPOSER, SUPPLIER AND/OR MANUFACTURER SHALL REFER TO ALL DOCUMENTS

PERTAINING TO THIS PROJECT AND COORDINATE ACCORDINGLY SO AS TO ENSURE ADEQUACY OF FIT, COMPLIANCE WITH SPECIFICATIONS, PROPER VOLTAGE AND CURRENT CHARACTERISTICS TO AVOID CONFLICT

WITH ANY OTHER BUILDINGS SYSTEMS. VERIFY SAME WITH SHOP DRAWINGS.

B. ADDITIONAL ELECTRICAL REQUIREMENTS MAY BE SHOWN ON PLANS FROM OTHER DISCIPLINES IN THIS SET. IT IS THE CONTRACTOR’S RESPONSIBILITY TO REVIEW ALL PLANS AND SPECIFICATIONS FOR A COMPLETE

UNDERSTANDING OF THE PROJECT REQUIREMENTS.

C. WORK SHALL BE IN ACCORDANCE WITH THE LATEST EDITION OF ALL LOCAL, STATE, AND NATIONAL CODES.

INCLUDING BUT NOT LIMITED TO NFPA 70 (NEC), NFPA 72, INTERNATIONAL BUILDING CODES, ETC.

D. CONTRACTOR SHALL FOLLOW SEISMIC RESTRAINT AND DESIGN REQUIREMENTS CONTAINED IN LATEST ADOPTED STATE AND INTERNATIONAL BUILDING CODES, WITH ALL AMENDMENTS AS ADOPTED BY THE CURRENT LEGISLATION. REFER TO ELECTRICAL AND STRUCTURAL SPECIFICATIONS FOR ADDITIONAL INFORMATION.

E. ALL OFFSETS, TURNS, FITTINGS, TRIM, DETAIL, ETC. MAY NOT BE INDICATED, BUT SHALL BE PROVIDED AS REQUIRED. ADDITIONAL ALLOWANCES SHALL BE INCLUDED FOR SAME AT EACH PROPOSER’S DISCRETION.

F. INSTALL NO PIPING, CONDUIT, DUCTWORK, ETC. IN A LOCATION OR IN A MANNER WHICH WILL ALLOW FREEZING

OR THE COLLECTION OF CONDENSATION THEREON. IF IN DOUBT, CONTACT THE ENGINEER.

G. ADVISE THE ENGINEER OF ANY CONFLICTS, ERRORS, OMISSIONS, ETC. AT LEAST TEN DAYS PRIOR TO BID DATE, TO ALLOW CLARIFICATION BY WRITTEN ADDENDUM.

H. WHERE CONFLICTS ARE FOUND BETWEEN DRAWINGS, DETAILS, OR SPECIFICATIONS, THE MORE STRINGENT

REQUIREMENT SHALL APPLY. NOTIFY ARCHITECT OF DISCREPANCY IN WRITING.

I. DEVIATION FROM SPECIFICATIONS OR PLANS REQUIRES PRIOR WRITTEN APPROVAL FROM THE ENGINEERS AND

MUST BE SUBMITTED IN WRITING NO LATER THAN TEN DAYS PRIOR TO THE BID DATE.

J. OBSERVE ALL APPLICABLE CODES, RULES AND REGULATIONS THAT MAY APPLY TO THE WORK UNDER THIS CONTRACT. (CITY, COUNTY, LOCAL, STATE, FEDERAL, MUNICIPALITY, UTILITY COMPANY, OSHA, ETC.).

K. MOUNTING HEIGHTS FOR WALL MOUNTED DEVICES INDICATED ABOVE FINISHED FLOOR ARE TO CENTER OF DEVICE UNO. MOUNTING HEIGHTS TO CEILING SUSPENDED DEVICES ARE TO BOTTOM OF DEVICE UNO.

L. INSTALL EQUIPMENT, MATERIALS, ETC. IN STRICT ACCORDANCE WITH MANUFACTURER’S RECOMMENDATIONS AND DIRECTIONS. IF IN CONFLICT WITH THE DESIGN INDICATED IN CONTRACT DOCUMENTS, ADVISE THE

ENGINEER PRIOR TO INSTALLATION FOR CLARIFICATION.

M. THE PURPOSE AND INTENT OF ALL OF THE DOCUMENTS PERTAINING TO THIS PROJECT IS TO PROVIDE A COMPLETE, FUNCTIONAL, SAFE, LIKE-NEW FACILITY. ANYTHING LESS SHALL BE UNACCEPTABLE.

N. ALL SYSTEMS, EQUIPMENT AND MATERIALS ARE TO BE INSTALLED IN A NEAT AND WORKMANLIKE MANNER.

WORK NOT MEETING THIS CRITERION SHALL BE REMOVED AND REINSTALLED SATISFACTORILY. FINAL DETERMINATION OF THE ACCEPTABILITY OF THE QUALITY OF WORK RESIDES WITH THE ENGINEER

O. ALL WORK, MATERIALS, EQUIPMENT, ETC. SHALL BE FULLY GUARANTEED FOR ONE FULL CALENDAR YEAR FROM THE DATE OF SUBSTANTIAL COMPLETION AS DOCUMENTED BY THE ENGINEER, UNLESS LONGER WARRANTY

PERIODS FOR EQUIPMENT ARE SPECIFIED.

P. UNLESS OTHERWISE SPECIFIED OR INDICATED, ALL EQUIPMENT AND/OR MATERIALS WITHIN OCCUPIED SPACES OR EXPOSED TO VIEW ON THE BUILDING EXTERIOR SHALL BE PRIMED AND FINISHED SO AS TO COMPLEMENT ADJACENT SURFACE, UNLESS OTHERWISE NOTED. COORDINATE WORK AND COLORS WITH ARCHITECT.

Q. COORDINATE WITH ARCHITECTURAL FLOOR PLANS, ELEVATIONS AND CASEWORK DETAILS FOR LOCATION OF

ADDITIONAL RECEPTACLES, UTILITY OUTLETS, ELECTRICAL DEVICES, ETC.

R. CEILING-MOUNTED ELECTRICAL DEVICES SHALL BE CENTERED IN 2'X2' CEILING TILE AND INSTALLED CENTERED ON 2' DIMENSION OF 2'X4' TILE AND ON CENTERLINE OR A QUARTER POINT ON 4' DIMENSION.

S. ANY VIBRATING, OSCILLATING OR OTHER NOISE OR MOTION PRODUCING EQUIPMENT SHALL BE ISOLATED FROM SURROUNDING SYSTEMS IN AN APPROVED MANNER. NOISY OR STRUCTURALLY DAMAGING INSTALLATIONS SHALL BE SATISFACTORILY REPLACED OR REPAIRED AT THE INSTALLING CONTRACTORS' EXPENSE. THE FINAL DECISION ON THE SUITABILITY OF A PARTICULAR INSTALLATION'S ACCEPTABILITY SHALL BE THAT OF THE

ENGINEER.

T. PROVIDE DETAILED SHOP DRAWINGS TO ENGINEER PRIOR TO PURCHASING OR INSTALLING ANY EQUIPMENT U. DEVIATIONS IN SIZES, CAPACITIES, FIT, FINISH, ETC. FOR EQUIPMENT FROM THAT PRIME SPECIFIED SHALL BE

THE RESPONSIBILITY OF THE PURCHASER OF THAT EQUIPMENT. ANY PROVISIONS REQUIRED TO ACCOMMODATE A DEVIATION, WHETHER APPROVED BY THE ENGINEER OR NOT, SHALL BE THE RESPONSIBILITY

OF THE PURCHASER.

V. THE CONSTRUCTION MANAGER, GENERAL CONTRACTOR, OR WHOMEVER HOLDS THE PRIME CONTRACT(S) FOR THIS CONSTRUCTION IS RESPONSIBLE FOR THE COORDINATION, APPEARANCE, SCHEDULING AND TIMELINESS OF THE WORK OF ALL TRADES, CONTRACTORS, SUPPLIERS, INSTALLERS, ETC. POOR OR UNTIMELY WORK ON THE PART OF ANY SUBCONTRACTOR SHALL BE RESOLVED BY THE PARTY WHO ENGAGED THEM ON THIS

PROJECT.

W. WHERE MOUNTING HEIGHTS ARE NOT INDICATED OR ARE IN CONFLICT WITH ANY OTHER BUILDING SYSTEM, CONTACT THE ENGINEER BEFORE AFFECTING INSTALLATION. REFER ALSO TO ARCHITECTURAL INTERIOR AND EXTERIOR ELEVATIONS, CEILING HEIGHTS AND OTHER DETAILS OF THESE DOCUMENTS, AS APPLICABLE.

X. WHERE FIRE-RATED CEILING ASSEMBLIES ARE NOTED, PROVIDE UL-LISTED FIRE-RATED GYPSUM BOARD OR PRE-MANUFACTURED ENCLOSURES ABOVE LUMINAIRES, CEILING DEVICES, ETC. IN OR ON CEILING, AS

REQUIRED TO MAINTAIN CEILING RATINGS.

Y. COORDINATE THE LOCATION OF DRAINS, ELECTRICAL OUTLETS, GAS OUTLETS, ETC. WITH ALL CASEWORK, KITCHEN EQUIPMENT, MECHANICAL ROOM EQUIPMENT, ETC. PRIOR TO COMMENCING INSTALLATION. WORK NOT SO COORDINATED SHALL BE REMOVED AND PROPERLY INSTALLED AT THE EXPENSE OF THE RESPONSIBLE

CONTRACTOR(S).

Z. ALL ELECTRICAL COMPONENTS OR EQUIPMENT SHALL BE LISTED AND LABELED BY UNDERWRITER'S LABORATORIES OR OTHER APPROVED LISTING AGENCY. APPROVAL AND LABELING OF INDIVIDUAL COMPONENTS ON AN ASSEMBLY IS NOT ACCEPTABLE AS MEETING THIS REQUIREMENT, UNLESS WAIVED BY THE

ENGINEER IN WRITING.

AA. ALL WIRING SYSTEMS SHALL BE INSTALLED WITH A MINIMUM OF SPLICES. CONDUCTORS, WHETHER SINGLE OR MULTI-PAIR, SHALL BE INSTALLED CONTINUOUS INSOFAR AS POSSIBLE FROM TERMINAL POINT TO TERMINAL

POINT.

BB. NO CONDUIT, SUPPORTS, ETC. SHALL BE RUN THROUGH ACCESS CLEARANCES OF EQUIPMENT BY OTHER

TRADES (I.E. VAV BOXES). COORDINATE WITH ALL TRADES PRIOR TO CONSTRUCTION.

CC. ALL CONTRACTORS SHALL EXERCISE EXTREME CARE IN THE COURSE OF THEIR WORK SO AS TO ENSURE THAT THEY DO NOT INTERRUPT ANY EXISTING SERVICE OR SUB-SERVICE FOR SAFETY PURPOSES. PAY PARTICULAR ATTENTION TO THIS PRECAUTION RELATIVE TO NATURAL GAS AND ELECTRICAL LINES. VERIFY THE LOCATION, SIZE, TYPE, ETC. OF EACH UNDERGROUND OR OVERHEAD UTILITY. ALL WORK SHALL BE PERFORMED IN ACCORDANCE WITH ALL FEDERAL, STATE AND/OR LOCAL RULES, REGULATIONS, STANDARD AND SAFETY REQUIREMENTS. UTILITIES SHALL BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE MUNICIPALITY OR UTILITY COMPANY STANDARDS. IN ALL CASES, THE MOST STRINGENT REQUIREMENT SHALL APPLY.

DD. ALL SUPPORTS FOR EQUIPMENT, DEVICES OR FIXTURES SHALL BE UNIQUE, DIRECTLY FROM THE BUILDING STRUCTURE. DO NOT SUPPORT WORK FROM OTHER TRADES EQUIPMENT OR SUPPORTS WITHOUT WRITTEN

PERMISSION FROM THE ENGINEER AND CONSENT OF THE OTHER TRADE, IN WRITING.

EE. WHERE INTERRUPTING AN EXISTING UTILITY OR SERVICE DELIBERATELY OR ACCIDENTALLY, THE RESPONSIBLE CONTRACTOR SHALL WORK CONTINUOUSLY AS NEEDED TO RESTORE SAME, PROVIDING PREMIUM TIME AS

NEEDED.

FF. REFER TO ARCHITECTURAL WALL ELEVATIONS (WHERE GIVEN) FOR HEIGHTS AND MOUNTING RELATIONSHIP OF OUTLETS AND EQUIPMENT. IF IN DOUBT, CONTACT ENGINEER FOR DIRECTION PRIOR TO ROUGH IN.

GG. AS APPLICABLE, REFER TO ARCHITECTURAL PHASING PLANS AND PHASING BOUNDARIES ON THESE DRAWINGS FOR SEQUENCING OF WORK, FULL EXTENT OF AREAS INVOLVED, EXTENT OF CEILING WORK, ETC. PROVIDE TEMPORARY CONNECTIONS FOR CIRCUITS AND WORK AS REQUIRED TO MAINTAIN SEQUENCE OF THE WORK

FROM PHASE TO PHASE.

HH. THIS CONTRACTOR SHALL BE RESPONSIBLE FOR ALL CUTTING AND PATCHING REQUIRED FOR HIS WORK. ALL CUTTING AND PATCHING SHALL BE IN ACCORDANCE WITH THE ARCHITECT'S STANDARDS FOR SUCH WORK.

II. ALL WORK SHALL BE CONCEALED UNLESS SPECIFICALLY INDICATED TO BE EXPOSED, OR REQUIRED TO BE EXPOSED. IF IN DOUBT, CONTACT THE ENGINEER FOR CLARIFICATIONS PRIOR TO INSTALLING ANY SUCH WORK.

JJ. WHERE BACKBOXES ARE LOCATED IN THE SAME VERTICAL CHANNEL/STUD SPACE ON OPPOSITE SIDES OF THE SAME WALL, PROVIDE SOUND-INSULATING PUTTY AROUND BOXES AS REQUIRED TO ELIMINATE SOUND

TRANSMISSION FROM ROOM TO ROOM.

KK. JUNCTION BOXES LOCATED ABOVE ACCESSIBLE CEILINGS SHALL BE LOCATED NO MORE THAN 36” ABOVE CEILING LEVEL. LABEL EACH BOX IN AREA OF WORK WITH A PERMANENT MARKER OR IN ACCORDANCE WITH

SPECIFICATIONS, WHICHEVER IS MORE STRINGENT.

LL. ALL MATERIALS FURNISHED AND ALL WORK INSTALLED SHALL COMPLY WITH THE CURRENT EDITION OF THE NATIONAL ELECTRICAL CODES, NATIONAL FIRE CODES OF THE NATIONAL FIRE PROTECTION ASSOCIATION, THE REQUIREMENTS OF LOCAL UTILITY COMPANIES, AND WITH THE REQUIREMENTS OF ALL GOVERNMENTAL AGENCIES OR DEPARTMENTS HAVING JURISDICTION. IF ANY CONFLICTS OR DISCREPANCIES OCCUR THE MOST

STRINGENT SHALL APPLY.

MM. DO NOT SCALE FROM DRAWINGS, AS PRINTING DISTORTS SCALE. WORK SHALL BE LAID OUT FROM

DIMENSIONED DRAWINGS, OR DIMENSIONS SUPPLIED TO THE CONTRACTOR.

NN. NOISY WORK, WORK OUTSIDE CONSTRUCTION BARRIERS, WORK IN OCCUPIED AREAS, ETC. SHALL BE PERFORMED AFTER HOURS OR ON WEEKENDS. COORDINATE EXACT SCHEDULING WITH FACILITY PRIOR TO

CONSTRUCTION.

OO. REFER TO ARCHITECTURAL PLANS FOR PHASING REQUIREMENTS. WORK SHALL BE COMPLETED IN PHASES PER THE PHASING PLAN AND AS COORDINATED WITH OWNER AND GENERAL CONTRACTOR. PROVIDE ALL REQUIRED INCREMENTAL INSPECTIONS, CERTIFICATIONS, ETC. AND ALL TEMPORARY SERVICES AS REQUIRED BY OWNER

TO ACCOMPLISH THE PHASING PLAN.

ELECTRICAL DEMOLITION NOTES:

A. DOTTED LINES INDICATE ITEMS FOR REMOVAL (UON) AND THIN SOLID LINES INDICATE

EXISTING ITEMS TO REMAIN.

B. THE CONTRACTOR SHALL MAINTAIN THE CONTINUITY OF EXISTING CIRCUITS THAT

CONTAIN DEVICES OR EQUIPMENT THAT ARE TO REMAIN. WHEN DEMOLITION OF AN

ELECTRICAL DEVICE (OR CIRCUIT) IS INDICATED ON THE DRAWINGS: THE CONTRACTOR

SHALL ENSURE THAT OTHER DEVICES OR EQUIPMENT "UPSTREAM" OR "DOWNSTREAM"

ON THE CIRCUITS SHALL REMAIN IN "PRE- DEMOLITION" WORKING ORDER. "LEFT-OVER"

CIRCUIT BREAKERS SHALL REMAIN, BE SWITCHED TO OFF POSITION, AND BE LABELED AS

SPARES IN THEIR PANELS. PROVIDE NEW TYPEWRITTEN DIRECTORIES FOR ALL PANELS

AFFECTED.

C. LOCATIONS OF DEVICES, CONNECTIONS, ETC., INDICATED ON THIS DRAWING WERE

TAKEN FROM VARIOUS SOURCES. THEY ARE DIAGRAMMATIC ONLY AND ARE SUBJECT TO

VARIATION FROM EXISTING CONDITIONS. CERTAIN EXISTING ELEMENTS MAY NOT BE

INDICATED AT ALL. THE CONTRACTOR PROPOSING TO DO ANY PART OF THE WORK

INDICATED HEREON SHALL VISIT THIS SITE AND DETERMINE TO HIS SATISFACTION THAT

THEY MAY COMPLETE ALL WORK REQUIRED FOR THE BID WHICH HE PROPOSES.

D. REMOVE ALL ASSOCIATED BACKBOXES, CONDUIT AND CONDUCTORS FOR DEVICES /

FIXTURES / ETC. BEING REMOVED (BACK TO SOURCE), WHETHER INDICATED OR NOT

(UON). CONTRACTOR SHALL PATCH AND REPAIR ANY EXISTING WALLS, FLOORS OR

CEILINGS WHERE DEVICES ARE SHOWN TO BE REMOVED (PATCH AND REPAIR TO

RECEIVE NEW FINISHES - SEE ARCHITECTURAL PLANS).

E. COORDINATE DISPOSAL OF ALL FIXTURES, DEVICES, ETC. (INDICATED FOR DEMOLITION)

WITH OWNER. TURN OVER ITEMS REMOVED TO OWNER AT THEIR OPTION.

F. COORDINATE WITH OTHER TRADES FOR THE REMOVAL AND/OR RELOCATION OF

ELECTRICAL DEVICES AND CONNECTIONS ASSOCIATED WITH THEIR EQUIPMENT.

G. PROVIDE TEMPORARY EMERGENCY EXIT LIGHTS AT CONSTRUCTION BARRIERS AS

REQUIRED.

H. CONTRACTOR SHALL PATCH AND REPAIR ALL EXISTING WALLS / CEILINGS AS REQUIRED

WHERE DEVICES ARE BEING REMOVED OR INSTALLED.

I. UNUSED/ABANDONED CONDUCTORS DISCOVERED ABOVE ACCESSIBLE CEILINGS SHALL

BE REMOVED IN ACCORDANCE WITH NEC REQUIREMENTS.

J. EXISTING ELECTRICAL SYSTEMS IN CONFLICT WITH CONSTRUCTION SHALL BE

RELOCATED TO PERMIT INSTALLATION OF DEVICES AND EQUIPMENT SHOWN ON PLANS.

K. DEVICES INDICATED WITH AN ''R'' SHALL BE RELOCATED. REMOVE, PROTECT, AND

REINSTALL IN NEW LOCATION INDICATED ON NEW WORK PLANS. INTERCEPT AND

EXTEND ALL EXISTING CABLING TO NEW LOCATION. CLEAN AND RE-LAMP RELOCATED

LUMINAIRES.

L. ALL EXISTING PANELS AFFECTED BY THIS CONTRACTOR'S WORK SHALL BE PROVIDED

WITH NEW TYPE-WRITTEN PANEL DIRECTORIES AND INSERT SLEEVES. PANEL

DIRECTORIES SHALL NOT USE ROOM NAMES OR NUMBERS FROM THESE DRAWINGS.

DIRECTORIES SHALL BE DETAILED AND COORDINATED WITH OWNER'S SUITE NUMBERS,

FINAL ROOM NUMBERS, IT RACK NAMES, WORKSTATION DESIGNATIONS, ETC. UNUSED

BREAKERS SHALL BE IN OFF POSITION.

GENERAL NOTES (LIGHTING):

A. REFER TO THE ARCHITECT'S REFLECTED CEILING PLANS, ELEVATIONS, AND CASEWORK

DETAILS FOR EXACT LOCATIONS OF ALL WALL AND CEILING MOUNTED ELECTRICAL

DEVICES.

B. CONTRACTOR SHALL FOLLOW BRANCH CIRCUITING LAY-OUT, AS INDICATED ON THE

FLOOR PLANS, WITH A MAXIMUM OF THREE (3) BRANCH CIRCUITS PER HOMERUN. EACH

BRANCH CIRCUIT SHALL BE PROVIDED WITH A DEDICATED NEUTRAL

CONDUCTOR. DEDICATED NEUTRAL CONDUCTORS SHALL BE CONSIDERED CURRENT

CARRYING. IF ADDITIONAL CONDUCTORS ARE RAN IN THE SAME CONDUIT WITH THOSE

INDICATED, CONTRACTOR SHALL DERATE ALL CURRENT CARRYING CONDUCTORS PER

N.E.C. #310.15(B)(3), AND UPSIZE CONDUIT AS REQUIRED PER N.E.C. #300.17 AND ANNEX C. MULTIWIRE BRANCH CIRCUITS AS DEFINED IN N.E.C #100 / 210.4 (CIRCUITS SHARING A

COMMON NEUTRAL CONDUCTOR) SHALL NOT BE PERMITTED.

C. IDENTIFY THE PANEL AND CIRCUIT NUMBER FOR ALL RECEPTACLES, SWITCHES, ETC. IN

AREA OF CONSTRUCTION. PROVIDE CLEAR ADHESIVE LABELS WITH BLACK LETTERING.

GENERAL NOTES (POWER):

A. REFER TO THE ARCHITECT'S REFLECTED CEILING PLANS, ELEVATIONS, AND CASEWORK

DETAILS FOR EXACT LOCATIONS OF ALL WALL AND CEILING MOUNTED ELECTRICAL

DEVICES.

B. CONTRACTOR SHALL FOLLOW BRANCH CIRCUITING LAY-OUT, AS INDICATED ON THE

FLOOR PLANS, WITH A MAXIMUM OF THREE (3) BRANCH CIRCUITS PER HOMERUN. EACH

BRANCH CIRCUIT SHALL BE PROVIDED WITH A DEDICATED NEUTRAL

CONDUCTOR. DEDICATED NEUTRAL CONDUCTORS SHALL BE CONSIDERED CURRENT

CARRYING. IF ADDITIONAL CONDUCTORS ARE RAN IN THE SAME CONDUIT WITH THOSE

INDICATED, CONTRACTOR SHALL DERATE ALL CURRENT CARRYING CONDUCTORS PER

NEC 310.15(B)(3), AND UPSIZE CONDUIT AS REQUIRED PER NEC 300.17 AND ANNEX

C. MULTIWIRE BRANCH CIRCUITS AS DEFINED IN NEC 100 / 210.4 (CIRCUITS SHARING A

COMMON NEUTRAL CONDUCTOR) SHALL NOT BE PERMITTED.

C. IDENTIFY THE PANEL AND CIRCUIT NUMBER FOR ALL RECEPTACLES, SWITCHES, ETC. IN

AREA OF CONSTRUCTION. PROVIDE CLEAR ADHESIVE LABELS WITH BLACK LETTERING.

MARK INSIDES OF ALL DEVICE BOXES WITH PANEL AND CIRCUIT NUMBER.

D. LOCATIONS OF ELECTRICAL CONNECTIONS AND LOCAL DISCONNECTS SHALL BE

COORDINATED WITH MECHANICAL AND PLUMBING CONTRACTORS TO ENSURE ACCESS

AND WORKING CLEARANCE IS MAINTAINED PER NEC. NOTIFY OTHER TRADES OF

REQUIRED CLEARANCE AREAS TO AVOID ROUTING OF OTHER SYSTEMS IN THESE AREAS.

DO NOT INSTALL ELECTRICAL EQUIPMENT OVER EQUIPMENT NAMEPLATES OR ACCESS

PANELS OR THROUGH ACCESS/MAINTENANCE CLEARANCES OF EQUIPMENT BY OTHER

TRADES.

F F

FACP

DINING

KITCHEN

STORAGE

DORM

COMMUNICATIONS

SHIFT

OFFICE

DORM

STORAGE

VESTIBULE

131CORRIDOR

WAP

AREA OF WORK

KITCHEN 134

STORAGE 133

DINING 135

6' 0"

DISPDW

REF

ICE

(E)LP1-1

(E)ELP1-1A

(E)ELP1-1

REF

EF-2

R R

E5 E13

E10

ELP1-1-18

E11

ELP1-1-22

ELP1-1-30

ELP1-1-34

ELP1-1-14

ELP1-1-24

ELP1-1-10

ELP1-1A-37

ELP1-1A-29

ELP1-1A-31

ELP1-1A-33

LIGHTING CIRCUIT: ELP1-1-13

ELP1-1-16

ELP1-1-8

ELP1-1-28

ELP1-1-26

LP1-21

ELP1-1A-37

ELP1-1A-35

E21

E12

E15

a a a a a b b c c c d c b a d

ELP1-1-20

EWC

ELP1-1-32

E22

E11

E29

ELP1-1-32

S y c a m o re S t, S u it e

C in c in n a ti

O H

2026-021

Cincinnati/Northern Kentucky International Airport

NORTH ARFF

FIRE STATION

Kitchen Remodel

D O

C U M

T, A N

D T

H E

S A N

D D

N S

C O

R A

D H

N , A

S A N

I N

R U M

O F

A L

R V

E, I S

O F

N , P

.S .C

A N

D I S

N O

B E

D I N

W H

O R I N

P A R T

R A

N Y

R O

C T, W

H O

U T

W R

A U

O R

O N

O F

B O

N , P

.S .C

C O

H T

-2

M B O

N , P

.S .C

E DATE DESCRIPTIONNO.

P ro je c ts

\P r2

-0

N o rt h A

R F

F K it c h e n R e m o d e l\ -D ra w in g s \6

.0 -C

15141312 161110987654321

6/30/26 BIDDING & PERMIT

906 Monmouth Street, Newport, KY 41071

EmbossDesign.com

(859)431-8612

E 0 0 1

E L E C T R I C A L D E M O L I T I O N P L A N

TAGGED NOTES

E1 DISCONNECT AND PROTECT EXISTING ANSUL CABINET.

CABINET TO BE RELOCATED IN NEW WORK PHASE.

E2 DISCONNECT AND REMOVE EXISTING DISHWASHER, WIRING,

AND JUNCTION BOX BACK TO WALL. DISHWASHER TO BE

REINSTALLED IN NEW WORK PHASE. DEMOLISH SWITCH.

MAINTAIN SWITCH BACKBOX AND WIRING FOR

RECONNECTION IN NEW WORK PHASE.

E3 DISCONNECT AND REMOVE EXISTING GARBAGE DISPOSAL,

WIRING, AND JUNCTION BOX BACK TO WALL. DISPOSAL TO BE

REINSTALLED IN NEW WORK PHASE. DEMOLISH SWITCH.

MAINTAIN SWITCH BACKBOX AND WIRING FOR

RECONNECTION IN NEW WORK PHASE.

E4 DEMOLISH EXISTING DEVICE AND MAINTAIN BACKBOX. DEVICE

TO BE REPLACED IN NEW WORK PHASE.

E5 REWORK PULL CORD TO NEW ANSUL PANEL LOCATION.

REFER TO NEW PLANS.

E8 DEMOLISH EXISTING UNDER CABINET LIGHTING. DEMOLISH

LIGHT SWITCH. PRESERVE BACKBOX FOR NEW SWITCH.

MAINTAIN BRANCH WIRING FOR NEW UNDER CABINET

LIGHTING.

E9 DEMOLISH EXISTING KITCHEN ISLAND RECEPTACLES.

REWORK BRANCH WIRING TO CONNECT NEW RECEPTACLES

IN NEW KITCHEN ISLAND. SEE E101 FOR MORE INFORMATION.

E10 PROTECT AND REMOVE EXISTING LIGHT FIXTURE. RETAIN

CONTROLS AND BRANCH WIRING. NEW FIXTURE TO BE

REINSTALLED IN SAME LOCATION IN NEW WORK PHASE.

E11 REMOVE EXISTING LIGHT SWITCH AND WIRING.

E12 DEMOLISH EXISTING DATA DEVICE AND COVER WITH BLANK

PLATE.

E13 EXISTING GAS ESTOP BUTTON TO BE RELOCATED. SEE NEW

WORK PLAN ON SHEET E101 FOR MORE INFORMATION.

E15 VERIFY EXISTING RECEPTACLE IS WIRED THROUGH EXISTING

HOOD CONTACTOR. IF NOT, CONTRACTOR TO EXTEND

BRANCH WIRING THROUGH KITCHEN HOOD CONTACTOR.

RECEPTACLE TO BE DE-ENERGIZED UPON ACTIVATION OF THE

ANSUL SYSTEM.

E21 DEMOLISH EXISTING RECEPTACLE AND BACKBOX. MAINTAIN

WIRING FOR RECONNECTION TO NEW RECEPTACLE. REWORK

TO NEW LOCATION IN NEW WORK PHASE.

E22 DISCONNECT AND REMOVE EXISTING EXIT SIGN. PROTECT

FOR REINSTALLATION IN NEW WORK PHASE.

E29 HOOD IS EXISTING TO REMAIN.

SCALE:E001 1/4" = 1'-0"

1 ELECTRICAL KITCHEN DEMO PLAN

WAP

AREA OF WORK

VESTIBULE 100

CORRIDOR 109

CORRIDOR 132

VESTIBULE 131

E34

E38

E34

E35

E38

E34

E35

E34

E36

E34

E35

E34

E22E36

E34E34E34

E34

E36

E35

EM STROBE

E37

E38E38E38

E38

E23

S y c a m o re S t, S u it e

C in c in n a ti

O H

2026-021

Cincinnati/Northern Kentucky International Airport

NORTH ARFF

FIRE STATION

Kitchen Remodel

D O

C U M

T, A N

D T

H E

S A N

D D

N S

C O

R A

D H

N , A

S A N

I N

R U M

O F

A L

R V

E, I S

O F

N , P

.S .C

A N

D I S

N O

B E

D I N

W H

O R I N

P A R T

R A

N Y

R O

C T, W

H O

U T

W R

A U

O R

O N

O F

B O

N , P

.S .C

C O

H T

-2

M B O

N , P

.S .C

E DATE DESCRIPTIONNO.

P ro je c ts

\P r2

-0

N o rt h A

R F

F K it c h e n R e m o d e l\ -D ra w in g s \6

.0 -C

15141312 161110987654321

6/30/26 BIDDING & PERMIT

906 Monmouth Street, Newport, KY 41071

EmbossDesign.com

(859)431-8612

E 0 0 2

E L E C T R I C A L C O R R C E I L I N G P L A N

TAGGED NOTES

E22 DISCONNECT AND REMOVE EXISTING EXIT SIGN. PROTECT

FOR REINSTALLATION IN NEW WORK PHASE.

E23 REINSTALL SALVAGED EXIT SIGN.

E34 REMOVE EXISTING LIGHT FIXTURE. MAINTAIN EXISTING

CONTROLS AND BRANCH CIRCUITRY FOR NEW LIGHT FIXTURE.

REFER TO NEW WORK PLAN.

E35 EXISTING EXIT SIGN TO REMAIN.

E36 REMOVE EXISTING DEVICE. MAINTAIN EXISTING WIRING FOR

REINSTALLATION. REFER TO NEW WORK PLAN.

E37 INSTALL NEW LED 2X4 FLAT PANEL. WIRE TO EXISTING

CONTROLS AND BRANCH CIRCUITRY. CONTRACTOR TO

ENSURE THAT EXISTING CONTROLS ARE ADEQUATE TO

OPERATE LIGHT FIXTURES UNTIL THE REST OF THE

BUILDING'S LIGHT FIXTURES AND LIGHTING CONTROLS ARE

REPLACED AT A LATER DATE.

E38 INSTALL NEW 6 INCH DOWNLIGHT. MAINTAIN EXISTING

CONTROLS AND BRANCH CIRCUITRY. CONTRACTOR TO

ENSURE THAT EXISTING CONTROLS ARE ADEQUATE TO

OPERATE LIGHT FIXTURES UNTIL THE REST OF THE

BUILDING'S LIGHT FIXTURES AND LIGHTING CONTROLS ARE

REPLACED AT A LATER DATE.

SCALE:E002 1/4" = 1'-0"

1 ELEC VESTI 100 CEILING DEMO PLAN

SCALE:E002 1/4" = 1'-0"

2 ELEC VESTI 100 CEILING NEW PLAN

SCALE:E002 1/4" = 1'-0"

3 ELEC VESTI 131 CEILING DEMO PLAN

SCALE:E002 1/4" = 1'-0"

4 ELEC VESTI 131 CEILING NEW PLAN

SCALE:E002 1/4" = 1'-0"

5 ELECTRICAL CORRIDOR CEILING DEMO PLAN

SCALE:E002 1/4" = 1'-0"

6 ELECTRICAL CORRIDOR CEILING NEW PLAN

ALL SCOPE SHOWN ON THIS

SHEET IS FOR ALTERNATE 1.

J J

B L

AREA OF WORK

PROPOSED CONDUIT ROUTING FOR NEW TEMP KITCH PANEL

PART OF APPARATUS BAY 145

& THE PLAN LEFT MEZZANINE LEVEL ABOVE THE BAY

APPARATUS BAY

ELPM1A-40

LPM-1-9

ELPM-1A-11

CORD REEL CORD REEL

(TYP)

E7-2TEMP KITCH

-1TEMP KITCH

-3,5TEMP KITCH

-4TEMP KITCH

-8TEMP KITCH

-7TEMP KITCH

-6TEMP KITCH

NEMA 14-50R

ELPM1A-40

ELPM-1A-11

EPO

E33

-10TEMP KITCH

E32

MEZZANINE

STAIR

(E)ELMP-1A

(E)ELPM-1

(E)LPM-1

LPM-1-3

ELPM-1-7

ELPM-1-7)

ELPM-1-7

ELP2-1-15

ELP2-1-13

ELP2-1-11

(E)ELP2-1

(E)FARP

(E)LP2-1

STOR./ELEC.

ELP2-1-9

(E) F-4

(E) F-5

(E) LC LD

(E) LL & LM

(E) LK & LN

TEMP KITCH

TEMP KITCH PNL

CONTACTOR

E26

E25

S y c a m o re S t, S u it e

C in c in n a ti

O H

2026-021

Cincinnati/Northern Kentucky International Airport

NORTH ARFF

FIRE STATION

Kitchen Remodel

D O

C U M

T, A N

D T

H E

S A N

D D

N S

C O

R A

D H

N , A

S A N

I N

R U M

O F

A L

R V

E, I S

O F

N , P

.S .C

A N

D I S

N O

B E

D I N

W H

O R I N

P A R T

R A

N Y

R O

C T, W

H O

U T

W R

A U

O R

O N

O F

B O

N , P

.S .C

C O

H T

-2

M B O

N , P

.S .C

E DATE DESCRIPTIONNO.

P ro je c ts

\P r2

-0

N o rt h A

R F

F K it c h e n R e m o d e l\ -D ra w in g s \6

.0 -C

15141312 161110987654321

6/30/26 BIDDING & PERMIT

906 Monmouth Street, Newport, KY 41071

EmbossDesign.com

(859)431-8612

E 1 0 0

E L E C T R I C A L T E M P O R A R Y P O W E R

TAGGED NOTES

E6 VERIFY ELECTRICAL REQUIREMENTS FOR TEMPORARY

KITCHEN STOVE WITH OWNER AND DESIGN TEAM PRIOR TO

INSTALLATION.

E7 ELECTRICAL CONTRACTOR SHALL INSTALL THREE (3) NEW

CORD REEL DROPS TO PROVIDE POWER FOR NEW

REFRIGERATORS IN THE TEMPORARY KITCHEN. THE CORD

REELS SHALL BE INSTALLED AT THE GARAGE CEILING, WITH

EXACT FINAL LOCATIONS DETERMINED IN THE FIELD. REFER

TO DETAIL 5 ON SHEET E200.

E25 PROVIDE 8P CONTACTOR WITH 120V, 1PH COIL TO DISABLE

POWER TO TEMPORARY KITCHEN WHEN EMERGENCY /

CRITICAL EVENT/CALL IS ACTIVE. PROVIDE WIRING AND

RELAY(S) AS REQUIRED TO CONNECT TO THE EXISTING FIRE

STATION ALTERING SYSTEM(S).

E26 PROVIDE TEMPORARY PANEL LOCATED ON MEZZANINE OF

BAY AREA. REFER TO SINGLE LINE AND KEY PLAN FOR

PROPOSED CONDUIT ROUTING.

E32 WIRE THIS CIRCUIT THROUGH THE CONTACTOR NEAR

SERVING PANEL. REFER TO KEYNOTE E25 AND DETAIL 4 ON

SHEET E200.

E33 REFER TO DETAIL 4 ON SHEET E200 FOR EPO CONNECTIONS.

COORDINATE WITH OWNER FOR EXACT PLACEMENT AND

INTEGRATION TO AUTOMATIC SHUTDOWN DURING DISPATCH

CALLS. PROVIDE WITH MANUAL RESET OF POWER TO

SHUTDOWN DEVICES AFTER THE DISPATCH CALL HAS BEEN

COMPLETED.

SCALE:E100 1/4" = 1'-0"

1 ELECTRICAL TEMPORARY KITCHEN PLAN

SCALE:E100 1/4" = 1'-0"

2 MEZZANINE LEVEL ELEC TEMP KITCHEN PLAN

DINING

KITCHEN

STORAGE

DORM

COMMUNICATIONS

CORRIDOR

F F

FACPJ

DINING

KITCHEN

STORAGE

DORM

COMMUNICATIONS

CORRIDOR

(E)LP1-1

(E)ELP1-1A

(E)ELP1-1

6' 0"

DISPDW

REF

ICE

REF

R R

ELP1-1-18 ELP1-1-22

ELP1-1-30

ELP1-1-34

ELP1-1-14

ELP1-1-24

ELP1-1-10

ELP1-1A-29

ELP1-1A-31

ELP1-1A-33

ELP1-1-16

ELP1-1-8

ELP1-1-28

ELP1-1-26

LP1-21

ELP1-1A-35

E15

E14

E17

ELP1-1-20

E20

E20 E20

E20

E20E20

E20

E18 E18 E18

E19

+64" AFF

E20

-37ELP1-1A

-37ELP1-1

-39ELP1-1

E30

-38ELP1-1A

E20

AREA OF WORK

KITCHEN 134

STORAGE 133

DINING 135

LIGHTING CIRCUIT: ELP1-1-13

(TYP)

E16

a a a a a b b d c b a d

LV1-D

F24 F24 F24

F24 F24

F24

(E)LP1-1

(E)ELP1-1A

(E)ELP1-1

c c c

UC UC UC

LV1-D

E23 c

(TYP)

E27

E28 a b,c d c

UC c

LV1-D

(TYP)

E16

OS CEILING MOUNTED OCCUPANCY SENSOR

A. LOW VOLTAGE CEILING MOUNTED OCCUPANCY SENSOR BASIS OF

DESIGN: nLIGHT nCM SERIES.

B. LIGHTING TO AUTOMATICALLY TURN ON TO 100% WHEN OCCUPANCY IS

DETECTED.

C. WHILE IN UNOCCUPIED MODE NORMAL AND EMERGENCY LIGHTING

SHALL TURN OFF.

D. LIGHTING SHALL HAVE AUTOMATIC SHUT-OFF OF LIGHTING WITHIN 15

MINUTES OF OCCUPANTS LEAVING.

E. WHERE LIFE-SAFETY LIGHTING CIRCUIT(S) ARE PRESENT, PROVIDE

UL924 DEVICE(S) TO REVERT LIGHTS TO 100% UPON FAILURE OF

NORMAL POWER.

ON / OFF

A. LOW VOLTAGE MANUAL CONTROL STATION WITH INDIVIDUAL BUTTONS AS

SHOWN ON DETAIL. BASIS OF DESIGN: nLIGHT nPODMA SERIES.

B. ADDITIONAL CONTROL INPUTS: VACANCY SENSOR, PHOTOCELL. REFER TO

FLOOR PLANS AND SEQUENCE OF OPERATIONS FOR ADDITIONAL CONTROL

REQUIREMENTS.

C. SWITCH REQUIREMENTS:

a. MANUAL ON BUTTON

b. MANUAL OFF BUTTON

c. RAISE BUTTON

d. LOWER BUTTON

$LV1-D LOW VOLTAGE ON/OFF, DIMMING CONTROL STATION

A. PROVIDE A STANDALONE LIGHTING CONTROL SYSTEM EQUAL TO nLIGHT BRANDS WITH ROOM

CONTROLLER TECHNOLOGY. REFER TO SPECIFICATIONS FOR ADDITIONAL ACCEPTABLE

MANUFACTURER.

B. PROVIDE FIRE-ALARM CONTROL/RELAY MODULE(S) AS REQUIRED TO MAKE LIGHTING CONTROL SYSTEM BRING ALL LIGHTING ON EGRESS PATHS TO 100% WHEN THE FIRE ALARM SYSTEM IS ACTIVATED.

C. INSTALL CONTROLLERS AND BRIDGES ABOVE ACCESSIBLE CEILING NEAR LUMINAIRE(S) TO BE CONTROLLED. PROVIDE CAD DRAWINGS INDICATING EXACT LOCATION OF CONTROL DEVICES AND

SUBMIT INFORMATION AS SHOP DRAWINGS FOR APPROVAL BY ENGINEER.

D. THE INTENTION IS TO PROVIDE A FULLY WIRED SYSTEM. WIRELESS AND/OR DEVICES THAT REQUIRE A

BATTERY ARE NOT ACCEPTABLE UNLESS SPECIFICALLY APPROVED BY THE ENGINEER.

E. CAT5, 5E, OR 6 NETWORK CABLE. NETWORK CABLE SHALL BE PLENUM RATED IF REQUIRED PER

SPECIFICATIONS AND /OR SITE CONDITIONS. MAXIMUM CABLE LENGTH PER ZONE 1500 FEET.

LIGHTING CONTROL GENERAL NOTES:

NETWORK CABLE USED TO

INTERCONNECT SWITCH TO

ROOM CONTROLLER

S y c a m o re S t, S u it e

C in c in n a ti

O H

2026-021

Cincinnati/Northern Kentucky International Airport

NORTH ARFF

FIRE STATION

Kitchen Remodel

D O

C U M

T, A N

D T

H E

S A N

This is the start of the file's text. The full file is on GovTribe.

File details come from the government source that posted it. Updated Jul 23, 2026.