Attachment_5_(Hazardous_Material_Survey)_-_Amendment_0002.pdf

Attachment 5 Hazardous Material Survey

FA9301-14-R-0011 - Amendment 0002

Asbestos Detected

Layer Name / Sample Description

Lab ID Sample Location

Bulk Asbestos Analysis by Polarized Light Microscopy

Non-Asbestos Constituents

Laboratory Report

0139001

NVLAP#101926-0

Client ID

Client:

Address: 412 TW/CEPM

EDWARDS AFB CA 93524

EDWARDS AFB

Date Received: 03/27/2014

03/27/2014Date Analyzed:

Job# / P.O. #:

EMC LABS, INC.

Collected: 03/26/2014

EPA Method: Project Name: BLDG 2850

Submitted By: MICHELE LaCOMBAddress:

Collected By:

9830 S. 51st Street, Suite B109, Phoenix, AZ 85044 Phone: 800-362-3373 or 480-940-5294 - Fax: (480) 893-1726

03/27/2014Date Reported:

EPA 600/R-93/116

Asbestos Type

225 N. ROSAMOND BLVD

NoLAYER 1 Paint, Beige

None Detected0139001-001 2850-CE-01 Carbonates

Binder/Filler

100%

YesLAYER 2 Texture / Paint, Green Note: Unable to separate adjacent layers

Chrysotile 3%

Carbonates Mica Binder/Filler

97%

NoLAYER 1 Paint, Beige

None Detected0139001-002 2850-CE-02 Carbonates

Binder/Filler

100%

YesLAYER 2 Texture / Paint, Green Note: Unable to separate adjacent layers

Chrysotile 2%

Carbonates Mica Binder/Filler

98%

Distinctly stratified, easily separable layers of samples are analyzed as subsamples of the whole and are reported separately for each discernible layer. All analyses are derived from calibrated visual estimate and measured in area percent unless otherwise noted. The report applies to the standards or procedures identified and to the sample(s) tested. The test results are not necessarily indicated or representative of the qualities of the lot from which the sample was taken or of apparently identical or similar products, nor do they represent an ongoing quality assurance program unless so noted. These reports are for the exclusive use of the addressed client and that they will not be reproduced wholly or in part for advertising or other purposes over our signature or in connection with our name without special written permission. The report shall not be reproduced except in full, without written approval by our laboratory. The samples not destroyed in testing are retained a maximum of thirty days. The laboratory measurement of uncertainty for the test method is approximately less than 1 by area percent.

Accredited by the National Institute of Standards and Technology, Voluntary Laboratory Accreditation Program for selected test method for asbestos. The accreditation or any reports generated by this laboratory in no way constitutes or implies product certification, approval, or endorsement by the National Institute of Standards and Technology. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. Polarized Light Microscopy may not be consistently reliable in detecting asbestos in floor coverings and similar non-friable organically bound materials.

Analyst - Kenneth Scheske Signatory - Lab Director - Kurt Kettler

Attachment 5 Hazardous Material Survey

EMC LABS, INC.

9830 South 51st Street, Suite B-109 / PHOENIX, ARIZONA 85044 / 480-940-5294 or 800-362-3373 / FAX 480-893-1726 emclab@emclabs.com

ANALYST: QA COORDINATOR:

Jason Thompson Kurt Kettler

Rev. 11/30/08

LEAD (Pb) IN PAINT CHIP SAMPLES

EMC SOP METHOD #L01/1 EPA SW-846 METHOD 7420

EMC LAB #: L51864 DATE RECEIVED: 03/27/14

CLIENT: Edwards AFB REPORT DATE: 03/27/14

DATE OF ANALYSIS: 03/27/14

CLIENT ADDRESS: 412th CE/CENMP 225 N. Rosamond Blvd.

Edwards AFB, CA 93524

P.O. NO.:

PROJECT NAME: Samples taken at Bldg. 2850 PROJECT NO.:

EMC #

L51864-

SAMPLE

DATE /14

CLIENT

SAMPLE #

DESCRIPTION

REPORTING

LIMIT

(%Pb by weight)

%Pb BY

WEIGHT

1 03/26 2850-CE-1L Paint – Beige / Green 0.010 0.044

2 03/26 2850-CE-2L Paint – Beige / Green 0.010 0.039 ^ = Dilution Factor Changed * = Excessive Substrate May Bias Sample Results BRL = Below Reportable Limits # = Very Small Amount Of Sample Submitted, May Affect Result

This report applies to the standards or procedures identified and to the samples tested only. The test results are not necessarily indicative or representative of the qualities of the lot from which the sample was taken or of apparently identical or similar products, nor do they represent an ongoing quality assurance program unless so noted. Unless otherwise noted, all quality control analyses for the samples noted above were within acceptable limits.

Where it is noted that a sample with excessive substrate was submitted for laboratory analysis, such analysis may be biased. The lead content of such sample may, in actuality, be greater than reported. EMC makes no warranty, express or implied, as to the accuracy of the analysis of samples noted to have been submitted with excessive substrate. Resampling is recommended in such situations to verify original laboratory results.

These reports are for the exclusive use of the addressed client and are rendered upon the condition that they will not be reproduced wholly or in part for advertising or other purposes over our signature or in connection with our name without special written permission. Samples not destroyed in testing are retained a maximum of sixty (60) days.