Exhibit E - Specifications for Self Prop 4 Wheel Broom.docx

State of Illinois Department of Central Management Services

Exhibit E Specifications for Diesel Powered, Self-Propelled Broom This specification describes a diesel powered, self-propelled broom to be used by the ordering entity for highway maintenance projects. The specifications for acceptable units by required features and accessories as outlined below.

Parts and services for the equipment should be readily available within the State of Illinois.

Unless otherwise specified, the proposed equipment shall be complete in all parts and ready for immediate use upon delivery.

The State reserves the right to waive minor informalities, deficiencies, or technical variances which by their nature are restrictive to a given manufacturer, if in its’ judgement, it would be in the best interest of the State.

The unit shall include the following standard or optional accessories and equipment Chassis:

The Broom shall be a full frame, enclosed cab, two axle design with a mid-mount rotary brush.

Engine:

The Broom shall be provided with a current production liquid cooled, turbo-charged, diesel engine meeting the following:

· 74 H.P. engine

· Tier4F emissions (Emission level furnished shall be the level required at manufacture)

· Dry style air cleaner

· Fuel filter water separator

· 12-volt electrical system

· Alternator/regulator

· Maintenance free battery

· Engine oil cooler The unit shall have approximately a 30-gallon fuel tank capacity. The tank or cap shall be clearly labeled “Diesel fuel only”.

The engine controls and instruments shall be included as follows:

· Key operated ignition or pass code

· Starter switch with neutral safety switch

· Hand or foot-controlled throttle

· Tachometer

· Fuel gauge

· Hour meter - activated by engine oil pressure or engine RPM.

· Engine coolant temperature gauge or warning light.

· Engine oil pressure gauge or warning light.

· Air filter restriction indicator, gauge, or warning light.

· Cold weather starting aid.

Transmission:

The transmission shall be a hydrostatic drive type with an infinitely variable pump and two speed motor driving a differential-type rear axle.

The transmission or gearbox shall feature a neutral position for towing.

Hydraulics:

The hydraulic system shall be manufacturers standard system with load compensated or load sensing pump.

The system shall be able to support any optional accessories that may be added.

The hydraulic system shall have approximately ± 25-gallon hydraulic reservoir with a 10-micron filter.

Tires and Wheels:

The wheels shall be heavy-duty automotive type, minimum 15” diameter, painted or powder coated manufacturer’s standard color.

The tires shall be new first run quality, automotive type, all season radial with load range required to meet gross weight of broom.

One spare tire and wheel assembly shall be included with each unit.

Brake System:

The brake system shall be manufacturer’s standard four-wheel hydraulic brake system, disc or drum design with mechanical parking brake.

Steering:

The steering shall be manufacturer’s hydraulic power steering, including tilt and telescoping features.

Cab and Accessories:

The cab shall be manufacturer’s deluxe option, sealed, air conditioned and heated with defrost.

The cab shall be constructed to incorporate an OSHA approved and SAE rated ROPS support structure.

The cab shall include the following:

· Fully adjustable, suspension style operators’ seat with arm rests and lap belt.

· Locking side access door(s).

· Front and rear windshield wipers with washer.

· Rear wheel fenders.

· Cab heater/defroster with air circulation system.

· Air conditioning.

· AM/FM radio with weather band and Bluetooth capabilities.

· Interior rear-view mirror.

· Locking storage.

· Open grate or anti-skid platform or steps for entry and exit of operators’ cab.

· Handholds or grab handles at each entry or exit point of operators’ cab.

· Slip resistant floor

· Information center/gauge cluster.

· SMV emblem mounted to the rear of the unit.

· Parking brake with warning light.

· Electric backup alarm.

· Left and right side exterior rear-view mirrors.

· Dome light

· 12v Power point Lighting:

The unit shall include complete lighting package including headlights, turn signals, and taillights.

The unit shall include work lights front and rear for nighttime operations.

The cab roof shall be equipped with an amber LED strobe light controlled by a separate switch by the operator.

Note: A non-LED rotating beacon does not satisfy this option.

Brush System:

The brush system shall be a mid-mount design, hydraulic direct drive, with a minimum sweeping width of 7’6”.

The brush sweep angle shall be a minimum of 45 degrees left or right.

The brush shall be a poly/steel type construction with a minimum width of 7’6”.

The brush core shall feature an industry standard quick-change design allowing a single operator to change out the brush at the jobsite.

A full-length steel brush cover with stone deflector shall cover the top and front of brush while operating.

Brush Water System:

This system shall aid in reducing dust during sweeping functions.

The system shall consist of a poly or non-corrosive water tank, pump, spray-bar and controls.

Approximate water tank capacity of 150 gallons.

Broom Controls:

The broom shall feature a joystick type control for operating brush sweep functions including the following, but not limited to:

· Brush On/Off

· Float control

· Speed control

· Lift and down pressure

· Right to Left Swing Finish:

All exterior surfaces normally painted, or powder coated shall be manufacturer’s standard color.

Additional Equipment:

All necessary counter weighting shall be provided to ensure both safe operation and transport after the installation of any option.

Tow Package:

This option shall include a heavy duty pintle eye tow bar/hitch, hardware, and safety chains to allow transport of the broom by a tow vehicle to and from the jobsite.

Scraper/Strike off Blade:

This option will equip the broom with a minimum 7’6” hydraulically controlled blade assembly to remove millings or other materials before sweeping.

The blade shall operate up and down, angle left or right and be controlled from the operator’s cab.

All hydraulic connections shall be the quick disconnect type.

The cutting edge shall be replaceable on the jobsite with standard tools.

Curb Brush:

This option will equip the broom with a front mount, direct drive hydraulic curb brush for sweeping along curbs, guardrails, and retaining walls.

The brush shall store in the vertical position when not in use.

Controls shall be in the operators’ cab and allow for adjustment while sweeping.

All hydraulic connections shall be the quick disconnect type.

The brush shall be a minimum 25” in diameter.