attachment_1_bid_171_25.pdf

SPECIFICATION- VAN, CUT AWAY, DUAL WHEEL- 11,000#- 2WD

TO INCLUDE ALL MANUFACTURERS STANDARD FEATURES INCLUDING:

GROSS VEHILCE WEIGHT RATING: MINIMUM 11,000 POUNDS

FRAME: UNIBODY CONSTRUCTION

WHEELBASE: 138”

CAB TO AXLE: 82.6 INCHES

CAB: REGULAR

ENGINE: GASOLINE MIN. 3.5 V6

TRANSMISSION: AUTOMATIC WITH AUXILIARY COOLER

AIR CONDITIONING: YES- FACTORY

CRUISE CONTROL: YES- FACTORY

COOLING: HEAVY DUTY

BRAKES: POWER- ABS, ALL WHEEL

STEERING: POWER

SUSPENSION: HEAVIEST AVAILABLE- TO INCLUDE HEAVY-

DUTY FRONT AXLE AND OVERLOAD SPRINGS

IN REAR if available

REAR RATIO: 3.73- DRW

LIMITED SLIP: YES

TIRES: TYPE, WHEEL/TIRE SIZE 6- ALL SEASON RADIAL TRUCK, 205/75R 16

SPARE TIRE: YES- FULL SIZE

JACK/WRENCH FOR SPARE: YES

RADIO/SPEAKERS AM/FM- FACTORY w/Bluetooth

ALTERNATOR: HEAVY DUTY, MIN 250 AMP

UPHOLSTERY- FRONT VINYL- MANUFACTURERS STANDARD-

2 PASSENGER CAPTAINS CHAIRS W/ ARM

RESTS AND LARGE CENTER CONSOLE

FLOOR COVER: VINYL

FLOOR MATS: VINYL OR RUBBER- FACTORY

WIPERS, INTERMITTENT: YES

MIRRORS, OUTSIDE R & L LONG ARM POWER ADJUSTING

BUMPER- FRONT: YES- STANDARD FRONT BUMPER

DAYTIME RUNNING LIGHTS: YES

FUEL CAPACITY: MINIMUM 31 GAL

TOW/HAUL MODE: YES

ELECTRONIC BRAKE CONTROLLER: YES, FACTORY

FRONT WHEEL WELL LINERS: YES

REAR CAMERA AND PREP KIT: YES

UPFITTER SWITCHES: YES, FACTORY – Four (4) minimum

UPFITTER PACKAGE: YES

AUX. FUSE PANEL: YES

PAINT: LEAD FREE WHITE, TO INCLUDE CAB CORNERS,

PAINTED TO MATCH CAB

SERVICE BODY

Construction/Configuration:

• Body to be constructed of aluminum.

• Exterior and interior of compartments shall be powder coated to match cab.

• Interior height 72”

• Compartment depth shall be minimum 15.5” with standard amount of adjustable trays.

• Plated chain or cable supports required on all horizontal doors.

• All vertical doors shall have spring loaded holders or struts.

• All compartment door hinges shall be bolt on type.

• All compartment doors shall be equipped with keyed alike locks, adjustable striker plates and stainless steel 2-stage safety catches. Adhesive mounted automotive type rubber seals shall be used on all doors.

• 2 two horizontal access doors in rear of body

• Compartment lighting

• All tail lights recessed and reflectors as required by state and federal laws shall be installed on the tailpiece.

• Double solid panel rear cargo doors with gas struts, key-alike with compartment doors, stainless steel rotary locks.

• Pass through door into cab. Door shall slide open not swing open.

• Two interior dome lights in cargo area.

• Roof top ladder rack installed

• Access ladder mounted on rear of body curbside.

• Standard body mounted “pooched” anti-slip bumper to be installed on rear bumper extension (see aerial lift specification).

• Rock guards shall be installed in the front lower corners of the service body

• Receiver hitch with 7-pole RV plug installed.

Mounting:

• The body cross members must bear directly on the truck frame or on a hardwood filler at least 2-1/2” wide, contoured to the truck frame to provide a level mounting surface where possible.

Warranty:

Ten year, limited warranty on:

No rust through, Door hinges, Latches and Locks, Shelves not bending under max load.

Color:

Lead free- Paint to match cab

Reference Information:

• The Reading “Ready Van Classic” Service Van model CSV72-DW when built and meeting the above specification is indicative of the design and quality required.