9-321373 - Concrete Paving Joint Sealants.pdf
PDF 158 KB Posted
- Solicitation number
- TB2672-NPA
- Issued by
- Salt Lake County, Salt Lake City, Utah
About this file
This is a Scope of Work specification document for the Salt Lake School District's Nibley Park School project, specifically detailing requirements for concrete paving joint sealants (Section 321373). The project involves sealing expansion and contraction joints within cement concrete pavement and joints between cement concrete and asphalt pavement in the northeast parking lot. The specification establishes comprehensive technical requirements for joint sealant installation, including product selection, quality assurance standards, and execution procedures. A mandatory pre-bid site visit is scheduled for Tuesday, May 26, 2026 at 9:00 A.M. at Nibley Park Elementary School (2785 South 800 East, Salt Lake City, Utah 84106), with attendance required for bid eligibility. Contractors must submit bids electronically through Bonfire/U3P, with all questions submitted in writing through that same platform or posed at the site visit.
The specification requires contractors to provide multiple submittals including product data, samples, certificates, qualification data, compatibility and adhesion test reports, and product test reports from qualified testing agencies. Joint sealants must comply with ASTM standards and be obtained from single manufacturers; available products include urethane, coal-tar-modified polymer, bitumen-modified urethane, silicone, and proprietary low-modulus sealant formulations from manufacturers such as Pecora Corporation, Meadows W.R. Inc., Tremco, Sonneborn, Crafco Inc., Dow Corning Corporation, and Koch Materials Company. Installation must occur only under specified temperature and moisture conditions, with backer materials meeting ASTM D 5249 standards. The contractor is required to maintain a daily log of all joints sealed in graphical format, submitted weekly to the Architect. All work must comply with manufacturer instructions and ASTM standards including ASTM C 1087, ASTM C 1021, ASTM C 1193, and ASTM E 548.
View the file
Other files
Show all 19
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
Salt Lake School District – Nibley Park School
321373 - 1 Concrete Paving Joint Sealants
SECTION 321373 - CONCRETE PAVING JOINT SEALANTS
PART 1 - GENERAL
1.1 RELATED DOCUMENTS
A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.
1.2 SUMMARY
A. This Section includes the following:
1. Expansion and contraction joints within cement concrete pavement.
2. Joints between cement concrete and asphalt pavement.
B. Related Sections include the following:
1. Division 07 Section "Joint Sealants" for sealing nontraffic and traffic joints in locations not specified in this Section.
2. Division 32 Section "Asphalt Paving" for constructing joints between concrete and asphalt pavement.
3. Division 32 Section "Concrete Paving" for constructing joints in concrete pavement.
1.3 SUBMITTALS
A. Product Data: For each joint-sealant product indicated.
B. Samples for Verification: For each type and color of joint sealant required. Install joint-sealant samples in 1/2-inch wide joints formed between two 6-inch long strips of material matching the appearance of exposed surfaces adjacent to joint sealants.
C. Product Certificates: For each type of joint sealant and accessory, signed by product manufacturer.
D. Qualification Data: For installer and testing agency.
E. Compatibility and Adhesion Test Reports: From sealant manufacturer, indicating the following:
1. Materials forming joint substrates and joint-sealant backings have been tested for compatibility and adhesion with joint sealants.
2. Interpretation of test results and written recommendations for primers and substrate preparation needed for adhesion.
F. Product Test Reports: Based on evaluation of comprehensive tests performed by a qualified testing agency, for sealants.
321373 - 2 Concrete Paving Joint Sealants
1.4 QUALITY ASSURANCE
A. Installer Qualifications: An employer of workers trained and approved by manufacturer.
B. Source Limitations: Obtain each type of joint sealant through one source from a single manufacturer.
C. Preconstruction Compatibility and Adhesion Testing: Submit to joint-sealant manufacturers, for testing indicated below, samples of materials that will contact or affect joint sealants.
1. Use ASTM C 1087 to determine whether priming and other specific joint preparation techniques are required to obtain rapid, optimum adhesion of joint sealants to joint substrates.
2. Submit not fewer than six (6) pieces of each type of material, including joint substrates, shims, joint-sealant backings, secondary seals, and miscellaneous materials.
3. Schedule sufficient time for testing and analyzing results to prevent delaying the Work.
4. For materials failing tests, obtain joint-sealant manufacturer's written instructions for corrective measures including use of specially formulated primers.
5. Testing will not be required if joint-sealant manufacturers submit joint preparation data that are based on previous testing of current sealant products for adhesion to, and compatibility with, joint substrates and other materials matching those submitted.
D. Product Testing: Obtain test results for "Product Test Reports" Paragraph in "Submittals" Article from a qualified testing agency based on testing of current sealant products within a 36-month period preceding the commencement of the Work.
1. Testing Agency Qualifications: An independent testing agency qualified according to ASTM C 1021 for testing indicated, as documented according to ASTM E 548.
1.5 DELIVERY, STORAGE, AND HANDLING
A. Deliver materials to Project site in original unopened containers or bundles with labels indicating manufacturer, product name and designation, color, expiration date, pot life, curing time, and mixing instructions for multi-component materials.
B. Store and handle materials to comply with manufacturer's written instructions to prevent their deterioration or damage due to moisture, high or low temperatures, contaminants, or other causes.
1.6 PROJECT CONDITIONS
A. Do not proceed with installation of joint sealants under the following conditions:
1. When ambient and substrate temperature conditions are outside limits permitted by joint-sealant manufacturer.
2. When ambient and substrate temperature conditions are outside limits permitted by joint-sealant manufacturer or are below 40 deg F.
3. When joint substrates are wet or covered with frost.
4. Where joint widths are less than those allowed by joint-sealant manufacturer for applications indicated.
5. Where contaminants capable of interfering with adhesion have not yet been removed from joint substrates.
321373 - 3 Concrete Paving Joint Sealants
PART 2 - PRODUCTS
2.1 MANUFACTURERS
A. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, products listed in other Part 2 articles.
B. Products: Subject to compliance with requirements, provide one of the products listed in other Part 2 articles.
2.2 MATERIALS, GENERAL
A. Compatibility: Provide joint sealants, backing materials, and other related materials that are compatible with one another and with joint substrates under conditions of service and application, as demonstrated by joint-sealant manufacturer based on testing and field experience.
B. Colors of Exposed Joint Sealants: As selected by Architect from manufacturer's full range.
2.3 COLD-APPLIED JOINT SEALANTS
A. Multi-component Jet-Fuel-Resistant Sealant for Concrete: Pourable, chemically curing elastomeric formulation complying with the following requirements for formulation and with ASTM C 920 for type, grade, class, and uses indicated:
1. Urethane Formulation: Type M; Grade P; Class 12-1/2; Uses T, M, and, as applicable to joint substrates indicated, O.
a. Available Products:
1) Pecora Corporation; Urexpan NR-300.
2) Engineer approved equal.
2. Coal-Tar-Modified Polymer Formulation: Type M; Grade P; Class 25; Uses T and, as applicable to joint substrates indicated, O.
a. Available Products:
1) Meadows, W. R., Inc.; Sealtight Gardox.
2) Engineer Approved Equal.
3. Bitumen-Modified Urethane Formulation: Type M; Grade P; Class 25; Uses T, M, and, as applicable to joint substrates indicated, O.
a. Available Products:
1) Tremco Sealant/Waterproofing Division; Vulkem 202.
2) Engineer approved Equal.
B. Single-Component Jet-Fuel-Resistant Urethane Sealant for Concrete: Single-component, pourable, coal-tar-modified, urethane formulation complying with ASTM C 920 for Type S;
Grade P; Class 25; Uses T, M, and, as applicable to joint substrates indicated, O.
321373 - 4 Concrete Paving Joint Sealants
1. Available Products:
a. Sonneborn, Div. of ChemRex, Inc.; Sonomeric 1.
b. Engineer Approved Equal.
C. Type NS Silicone Sealant for Concrete: Single-component, low-modulus, neutral-curing, nonsag silicone sealant complying with ASTM D 5893 for Type NS.
1. Available Products:
a. Crafco Inc.; RoadSaver Silicone.
b. Dow Corning Corporation; 888.
c. Engineer Approved Equal.
D. Type SL Silicone Sealant for Concrete and Asphalt: Single-component, low-modulus, neutral-curing, self-leveling silicone sealant complying with ASTM D 5893 for Type SL.
1. Available Products:
a. Crafco Inc.; RoadSaver Silicone SL.
b. Dow Corning Corporation; 890-SL.
c. Engineer Approved Equal.
E. Multi-component Low-Modulus Sealant for Concrete and Asphalt: Proprietary formulation consisting of reactive petropolymer and activator components producing a pourable, self-leveling sealant.
1. Available Products:
a. Meadows, W. R., Inc.; Sof-Seal.
b. Engineer Approved Equal.
2.4 HOT-APPLIED JOINT SEALANTS
A. Jet-Fuel-Resistant Elastomeric Sealant for Concrete: Single-component formulation complying with ASTM D 3569.
1. Available Products:
a. Crafco Inc.; Superseal 444/777.
b. Meadows, W. R., Inc.; Poly-Jet 3569.
c. Engineer Approved Equal.
B. Jet-Fuel-Resistant Sealant for Concrete and Tar Concrete: Single-component formulation complying with ASTM D 3581.
1. Available Products:
a. Crafco Inc.; Superseal 1614A.
b. Meadows, W. R., Inc.; Poly-Jet 1614.
c. Meadows, W. R., Inc.; Poly-Jet 3406.
d. Meadows, W. R., Inc.; Poly-Jet 3569.
e. Engineer Approved Equal.
321373 - 5 Concrete Paving Joint Sealants
C. Elastomeric Sealant for Concrete: Single-component formulation complying with ASTM D 3406.
1. Available Products:
a. Crafco Inc.; Superseal 444/777.
b. Meadows, W. R., Inc.; Poly-Jet 3406.
c. Engineer Approved Equal.
D. Sealant for Concrete and Asphalt: Single-component formulation complying with
ASTM D 3405.
1. Available Products:
a. Koch Materials Company; Product No. 9005.
b. Koch Materials Company; Product No. 9030.
c. Meadows, W. R., Inc.; Sealtight Hi-Spec.
d. Engineer Approved Equal.
2.5 JOINT-SEALANT BACKER MATERIALS
A. General: Provide joint-sealant backer materials that are nonstaining; are compatible with joint substrates, sealants, primers, and other joint fillers; and are approved for applications indicated by joint-sealant manufacturer based on field experience and laboratory testing.
B. Round Backer Rods for Cold- and Hot-Applied Sealants: ASTM D 5249, Type 1, of diameter and density required to control sealant depth and prevent bottom-side adhesion of sealant.
C. Backer Strips for Cold- and Hot-Applied Sealants: ASTM D 5249; Type 2; of thickness and width required to control sealant depth, prevent bottom-side adhesion of sealant, and fill remainder of joint opening under sealant.
D. Round Backer Rods for Cold-Applied Sealants: ASTM D 5249, Type 3, of diameter and density required to control sealant depth and prevent bottom-side adhesion of sealant.
2.6 PRIMERS
A. Primers: Product recommended by joint-sealant manufacturer where required for adhesion of sealant to joint substrates indicated, as determined from preconstruction joint-sealant-substrate tests and field tests.
PART 3 - EXECUTION
3.1 EXAMINATION
A. Examine joints indicated to receive joint sealants, with Installer present, for compliance with requirements for joint configuration, installation tolerances, and other conditions affecting joint-sealant performance.
1. Proceed with installation only after unsatisfactory conditions have been corrected.
321373 - 6 Concrete Paving Joint Sealants
3.2 PREPARATION
A. Surface Cleaning of Joints: Clean out joints immediately before installing joint sealants to comply with joint-sealant manufacturer's written instructions.
B. Joint Priming: Prime joint substrates where indicated or where recommended in writing by joint-sealant manufacturer, based on preconstruction joint-sealant-substrate tests or prior experience. Apply primer to comply with joint-sealant manufacturer's written instructions.
Confine primers to areas of joint-sealant bond; do not allow spillage or migration onto adjoining surfaces.
3.3 INSTALLATION OF JOINT SEALANTS
A. General: Comply with joint-sealant manufacturer's written installation instructions for products and applications indicated, unless more stringent requirements apply.
B. Sealant Installation Standard: Comply with recommendations in ASTM C 1193 for use of joint sealants as applicable to materials, applications, and conditions indicated.
C. Install backer materials of type indicated to support sealants during application and at position required to produce cross-sectional shapes and depths of installed sealants relative to joint widths that allow optimum sealant movement capability.
1. Do not leave gaps between ends of backer materials.
2. Do not stretch, twist, puncture, or tear backer materials.
3. Remove absorbent backer materials that have become wet before sealant application and replace them with dry materials.
D. Install sealants using proven techniques that comply with the following and at the same time backings are installed:
1. Place sealants so they directly contact and fully wet joint substrates.
2. Completely fill recesses provided for each joint configuration.
3. Produce uniform, cross-sectional shapes and depths relative to joint widths that allow optimum sealant movement capability.
E. Tooling of Nonsag Sealants: Immediately after sealant application and before skinning or curing begins, tool sealants according to requirements specified below to form smooth, uniform beads of configuration indicated; to eliminate air pockets; and to ensure contact and adhesion of sealant with sides of joint.
1. Remove excess sealants from surfaces adjacent to joint.
2. Use tooling agents that are approved in writing by joint-sealant manufacturer and that do not discolor sealants or adjacent surfaces.
F. Provide joint configuration to comply with joint-sealant manufacturer's written instructions, unless otherwise indicated.
G. Provide recessed joint configuration for silicone sealants of recess depth and at locations indicated.
321373 - 7 Concrete Paving Joint Sealants
3.4 CLEANING
A. Clean off excess sealants or sealant smears adjacent to joints as the Work progresses by methods and with cleaning materials approved by manufacturers of joint sealants and of products in which joints occur.
3.5 PROTECTION
A. Protect joint sealants during and after curing period from contact with contaminating substances and from damage resulting from construction operations or other causes so sealants are without deterioration or damage at time of Substantial Completion. If, despite such protection, damage or deterioration occurs, cut out and remove damaged or deteriorated joint sealants immediately and replace with joint sealant so installations with repaired areas are indistinguishable from the original work.
3.6 DOCUMENTATION
A. The contractor shall keep a daily log of all joints sealed in graphical format. This shall be submitted to the Architect on a weekly basis.
END OF SECTION 321373
| PART 1 - GENERAL |
| 1.1 RELATED DOCUMENTS |
| A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. |
| 1.2 SUMMARY |
| A. This Section includes the following: |
| 1. Expansion and contraction joints within cement concrete pavement. |
| 2. Joints between cement concrete and asphalt pavement. |
| B. Related Sections include the following: |
| 1. Division 07 Section "Joint Sealants" for sealing nontraffic and traffic joints in locations not specified in this Section. |
| 2. Division 32 Section "Asphalt Paving" for constructing joints between concrete and asphalt pavement. |
| 3. Division 32 Section "Concrete Paving" for constructing joints in concrete pavement. |
| 1.3 SUBMITTALS |
| A. Product Data: For each joint-sealant product indicated. |
| B. Samples for Verification: For each type and color of joint sealant required. Install joint-sealant samples in 1/2-inch wide joints formed between two 6-inch long strips of material matching the appearance of exposed surfaces adjacent to joint sea... |
| C. Product Certificates: For each type of joint sealant and accessory, signed by product manufacturer. |
| D. Qualification Data: For installer and testing agency. |
| E. Compatibility and Adhesion Test Reports: From sealant manufacturer, indicating the following: |
| 1. Materials forming joint substrates and joint-sealant backings have been tested for compatibility and adhesion with joint sealants. |
| 2. Interpretation of test results and written recommendations for primers and substrate preparation needed for adhesion. |
F. Product Test Reports: Based on evaluation of comprehensive tests performed by a qualified testing agency, for sealants.
| 1.4 QUALITY ASSURANCE |
| A. Installer Qualifications: An employer of workers trained and approved by manufacturer. |
| B. Source Limitations: Obtain each type of joint sealant through one source from a single manufacturer. |
| C. Preconstruction Compatibility and Adhesion Testing: Submit to joint-sealant manufacturers, for testing indicated below, samples of materials that will contact or affect joint sealants. |
| 1. Use ASTM C 1087 to determine whether priming and other specific joint preparation techniques are required to obtain rapid, optimum adhesion of joint sealants to joint substrates. |
| 2. Submit not fewer than six (6) pieces of each type of material, including joint substrates, shims, joint-sealant backings, secondary seals, and miscellaneous materials. |
| 3. Schedule sufficient time for testing and analyzing results to prevent delaying the Work. |
| 4. For materials failing tests, obtain joint-sealant manufacturer's written instructions for corrective measures including use of specially formulated primers. |
| 5. Testing will not be required if joint-sealant manufacturers submit joint preparation data that are based on previous testing of current sealant products for adhesion to, and compatibility with, joint substrates and other materials matching those su... |
| D. Product Testing: Obtain test results for "Product Test Reports" Paragraph in "Submittals" Article from a qualified testing agency based on testing of current sealant products within a 36-month period preceding the commencement of the Work. |
| 1. Testing Agency Qualifications: An independent testing agency qualified according to ASTM C 1021 for testing indicated, as documented according to ASTM E 548. |
| 1.5 DELIVERY, STORAGE, AND HANDLING |
| A. Deliver materials to Project site in original unopened containers or bundles with labels indicating manufacturer, product name and designation, color, expiration date, pot life, curing time, and mixing instructions for multi-component materials. |
| B. Store and handle materials to comply with manufacturer's written instructions to prevent their deterioration or damage due to moisture, high or low temperatures, contaminants, or other causes. |
| 1.6 PROJECT CONDITIONS |
| A. Do not proceed with installation of joint sealants under the following conditions: |
| 1. When ambient and substrate temperature conditions are outside limits permitted by joint-sealant manufacturer. |
| 2. When ambient and substrate temperature conditions are outside limits permitted by joint-sealant manufacturer or are below 40 deg F. |
| 3. When joint substrates are wet or covered with frost. |
| 4. Where joint widths are less than those allowed by joint-sealant manufacturer for applications indicated. |
| 5. Where contaminants capable of interfering with adhesion have not yet been removed from joint substrates. |
| PART 2 - PRODUCTS |
| 2.1 MANUFACTURERS |
| A. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, products listed in other Part 2 articles. |
| B. Products: Subject to compliance with requirements, provide one of the products listed in other Part 2 articles. |
| 2.2 MATERIALS, GENERAL |
| A. Compatibility: Provide joint sealants, backing materials, and other related materials that are compatible with one another and with joint substrates under conditions of service and application, as demonstrated by joint-sealant manufacturer based o... |
| B. Colors of Exposed Joint Sealants: As selected by Architect from manufacturer's full range. |
| 2.3 COLD-APPLIED JOINT SEALANTS |
| A. Multi-component Jet-Fuel-Resistant Sealant for Concrete: Pourable, chemically curing elastomeric formulation complying with the following requirements for formulation and with ASTM C 920 for type, grade, class, and uses indicated: |
| 1. Urethane Formulation: Type M; Grade P; Class 12-1/2; Uses T, M, and, as applicable to joint substrates indicated, O. |
| a. Available Products: |
| 1) Pecora Corporation; Urexpan NR-300. |
| 2) Engineer approved equal. |
| 2. Coal-Tar-Modified Polymer Formulation: Type M; Grade P; Class 25; Uses T and, as applicable to joint substrates indicated, O. |
| a. Available Products: |
| 1) Meadows, W. R., Inc.; Sealtight Gardox. |
| 2) Engineer Approved Equal. |
| 3. Bitumen-Modified Urethane Formulation: Type M; Grade P; Class 25; Uses T, M, and, as applicable to joint substrates indicated, O. |
| a. Available Products: |
| 1) Tremco Sealant/Waterproofing Division; Vulkem 202. |
| 2) Engineer approved Equal. |
| B. Single-Component Jet-Fuel-Resistant Urethane Sealant for Concrete: Single-component, pourable, coal-tar-modified, urethane formulation complying with ASTM C 920 for Type S; Grade P; Class 25; Uses T, M, and, as applicable to joint substrates indic... |
| 1. Available Products: |
| a. Sonneborn, Div. of ChemRex, Inc.; Sonomeric 1. |
| b. Engineer Approved Equal. |
| C. Type NS Silicone Sealant for Concrete: Single-component, low-modulus, neutral-curing, nonsag silicone sealant complying with ASTM D 5893 for Type NS. |
| 1. Available Products: |
| a. Crafco Inc.; RoadSaver Silicone. |
| b. Dow Corning Corporation; 888. |
| c. Engineer Approved Equal. |
| D. Type SL Silicone Sealant for Concrete and Asphalt: Single-component, low-modulus, neutral-curing, self-leveling silicone sealant complying with ASTM D 5893 for Type SL. |
| 1. Available Products: |
| a. Crafco Inc.; RoadSaver Silicone SL. |
| b. Dow Corning Corporation; 890-SL. |
| c. Engineer Approved Equal. |
| E. Multi-component Low-Modulus Sealant for Concrete and Asphalt: Proprietary formulation consisting of reactive petropolymer and activator components producing a pourable, self-leveling sealant. |
| 1. Available Products: |
| a. Meadows, W. R., Inc.; Sof-Seal. |
| b. Engineer Approved Equal. |
| 2.4 HOT-APPLIED JOINT SEALANTS |
| A. Jet-Fuel-Resistant Elastomeric Sealant for Concrete: Single-component formulation complying with ASTM D 3569. |
| 1. Available Products: |
| a. Crafco Inc.; Superseal 444/777. |
| b. Meadows, W. R., Inc.; Poly-Jet 3569. |
| c. Engineer Approved Equal. |
| B. Jet-Fuel-Resistant Sealant for Concrete and Tar Concrete: Single-component formulation complying with ASTM D 3581. |
| 1. Available Products: |
| a. Crafco Inc.; Superseal 1614A. |
| b. Meadows, W. R., Inc.; Poly-Jet 1614. |
| c. Meadows, W. R., Inc.; Poly-Jet 3406. |
| d. Meadows, W. R., Inc.; Poly-Jet 3569. |
| e. Engineer Approved Equal. |
| C. Elastomeric Sealant for Concrete: Single-component formulation complying with ASTM D 3406. |
| 1. Available Products: |
| a. Crafco Inc.; Superseal 444/777. |
| b. Meadows, W. R., Inc.; Poly-Jet 3406. |
| c. Engineer Approved Equal. |
| D. Sealant for Concrete and Asphalt: Single-component formulation complying with ASTM D 3405. |
| 1. Available Products: |
| a. Koch Materials Company; Product No. 9005. |
| b. Koch Materials Company; Product No. 9030. |
| c. Meadows, W. R., Inc.; Sealtight Hi-Spec. |
| d. Engineer Approved Equal. |
| 2.5 JOINT-SEALANT BACKER MATERIALS |
| A. General: Provide joint-sealant backer materials that are nonstaining; are compatible with joint substrates, sealants, primers, and other joint fillers; and are approved for applications indicated by joint-sealant manufacturer based on field experi... |
| B. Round Backer Rods for Cold- and Hot-Applied Sealants: ASTM D 5249, Type 1, of diameter and density required to control sealant depth and prevent bottom-side adhesion of sealant. |
| C. Backer Strips for Cold- and Hot-Applied Sealants: ASTM D 5249; Type 2; of thickness and width required to control sealant depth, prevent bottom-side adhesion of sealant, and fill remainder of joint opening under sealant. |
| D. Round Backer Rods for Cold-Applied Sealants: ASTM D 5249, Type 3, of diameter and density required to control sealant depth and prevent bottom-side adhesion of sealant. |
| 2.6 PRIMERS |
| A. Primers: Product recommended by joint-sealant manufacturer where required for adhesion of sealant to joint substrates indicated, as determined from preconstruction joint-sealant-substrate tests and field tests. |
| PART 3 - EXECUTION |
| 3.1 EXAMINATION |
| A. Examine joints indicated to receive joint sealants, with Installer present, for compliance with requirements for joint configuration, installation tolerances, and other conditions affecting joint-sealant performance. |
| 1. Proceed with installation only after unsatisfactory conditions have been corrected. |
| 3.2 PREPARATION |
| A. Surface Cleaning of Joints: Clean out joints immediately before installing joint sealants to comply with joint-sealant manufacturer's written instructions. |
| B. Joint Priming: Prime joint substrates where indicated or where recommended in writing by joint-sealant manufacturer, based on preconstruction joint-sealant-substrate tests or prior experience. Apply primer to comply with joint-sealant manufacture... |
| 3.3 INSTALLATION OF JOINT SEALANTS |
| A. General: Comply with joint-sealant manufacturer's written installation instructions for products and applications indicated, unless more stringent requirements apply. |
| B. Sealant Installation Standard: Comply with recommendations in ASTM C 1193 for use of joint sealants as applicable to materials, applications, and conditions indicated. |
| C. Install backer materials of type indicated to support sealants during application and at position required to produce cross-sectional shapes and depths of installed sealants relative to joint widths that allow optimum sealant movement capability. |
| 1. Do not leave gaps between ends of backer materials. |
| 2. Do not stretch, twist, puncture, or tear backer materials. |
| 3. Remove absorbent backer materials that have become wet before sealant application and replace them with dry materials. |
| D. Install sealants using proven techniques that comply with the following and at the same time backings are installed: |
| 1. Place sealants so they directly contact and fully wet joint substrates. |
| 2. Completely fill recesses provided for each joint configuration. |
| 3. Produce uniform, cross-sectional shapes and depths relative to joint widths that allow optimum sealant movement capability. |
| E. Tooling of Nonsag Sealants: Immediately after sealant application and before skinning or curing begins, tool sealants according to requirements specified below to form smooth, uniform beads of configuration indicated; to eliminate air pockets; and... |
| 1. Remove excess sealants from surfaces adjacent to joint. |
| 2. Use tooling agents that are approved in writing by joint-sealant manufacturer and that do not discolor sealants or adjacent surfaces. |
| F. Provide joint configuration to comply with joint-sealant manufacturer's written instructions, unless otherwise indicated. |
| G. Provide recessed joint configuration for silicone sealants of recess depth and at locations indicated. |
| 3.4 CLEANING |
| A. Clean off excess sealants or sealant smears adjacent to joints as the Work progresses by methods and with cleaning materials approved by manufacturers of joint sealants and of products in which joints occur. |
| 3.5 PROTECTION |
| A. Protect joint sealants during and after curing period from contact with contaminating substances and from damage resulting from construction operations or other causes so sealants are without deterioration or damage at time of Substantial Completio... |
| 3.6 DOCUMENTATION |
| A. The contractor shall keep a daily log of all joints sealed in graphical format. This shall be submitted to the Architect on a weekly basis. |
File details come from the government source that posted it. Updated .