055000-6.0_Metal Fabrications-Suicide Fence-SD_ASI_ACG.pdf
PDF 264 KB Posted
- Solicitation number
- 36C25926R0082_1
About this file
This is a technical drawing and submittal document for a 4-foot square aluminum fence panel with mesh infill, prepared by MFR Manufacturing Corporation, Inc. for the Veterans Affairs Medical Center (VAMC) Oklahoma City facility. The panel features a 4-foot by 4-foot frame with a 3-foot 8-inch by 3-foot 8-inch mesh infill area, with a 4-inch opening at the top. The frame is constructed with 1-inch edges and uses aluminum mesh with 4-inch by 4-inch spacing. The finish specification is powder coating in black.
The document includes comprehensive technical specifications, a bill of materials, connection details, and general notes regarding fabrication tolerances (±1/4 inch on all dimensions), field verification requirements, and installation responsibilities. Key contractual provisions specify that the customer is responsible for verifying all dimensions before fabrication, that surrounding structural support must be designed to withstand transmitted forces, and that mechanical fasteners are the installer's responsibility unless otherwise noted. The document requires customer signature and approval with red-line marking of any necessary changes. MFR Manufacturing Corporation retains all design and intellectual property rights to the drawings. The submittal is dated April 1, 2025, with fabrication coordinated by drawing verification procedures outlined on subsequent pages.
View the file
Other files
Show all 25
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
" [1
08]
OC
1 4"
8] O
C
4" [10
1] O
PEN
ING
2"
4'-0" [1219] FRAME WIDTH
3'-8" [1118] MESH INFILL WIDTH
3' -8
[1
M
ES
H
IN
FI
LL
H
EI
G
HT
4' -0
[1
9] F
RA
M E
HE
IG
HT
1" [25]
3"
3"
4'-0" [1219] FRAME WIDTH
3'-8" [1118] MESH INFILL WIDTH
1 14" [32] 4" [19]
FRONT VIEW
TOP VIEW
FRONT VIEW
1" [25] 1 14" [32]
2"
3 4"
2"
4"
2]
2 1 4" [58]
R 58 " [R16]
158" [41]
DRAWN BY: CHECKED BY:
DATE:SCALE:
JOB NO.
SHEET NO.
S
IL
L
AV
E, A
UR
OR
A
IL
(8
2-
W W
W .M
FR
CO
RP
.C
O M
V A
M C
O K
C
M A S T E R S
H E E T
C O N N E C T
IO
N D
E T A
IL
B
IL
L O
F M
A T E R
IA
L C
H A R T
4/1/2025AS NOTED
BB GM
A1PLEASE INITIAL AND DATE THE FOLLOWING PAGES ON THE BOTTOM RIGHT HAND
CORNER FOR THE PURPOSE OF DRAWING VERIFICATION.
CUSTOMER SIGNATURE AND APPROVAL
DATE SIGNED
APPROVED BY DATE SENT
SUBMITTAL #
( SIGNATURE )
GENERAL ABBREVIATIONS
AFF = ABOVE FINISHED FLOOR
= ARCHITECTARCH.
B.O. = BY OTHERS
B.P. = BASE PLATE
= BAR DIRECTION
= CENTER LINECL
CLR = CLEARANCE
CMU = CONCRETE MASONRY UNIT
DIM = DIMENSIONS
Ø = DIAMETER
(E) = EXISTING
FCTF = FIELD CUT TO FIT
FH = FRAME HEIGHT
FL = FLOOR
FS = FAR SIDE
FW = FRAME WIDTH
GC = GENERAL CONTRACTOR
GL = GROUND LEVEL
ITI
H = HEIGHT
= INSIDE TO INSIDE
(OPENING)
L = LENGTH
L1 = OPENING
L2 = PANEL WIDTH
NS = NEAR SIDE
OC = ON CENTER
O.H. = OPPOSITE HAND
O/O = OWNER/OPERATOR
OTO = OUTSIDE TO OUTSIDE
(OPENING)
P = PANEL
PL = PLATE
R.O. = ROUGH OPENING
TYP. = TYPICAL
VIF = VERIFY IN FIELD
WIF = WELD IN FIELD
R E V B
Y R E V
D A T E
R E V
IS
E D I T E M S
R E V
N O - - - -
DRAWING INDEX
FINISH: POWDER COATED
COLOR: BLACK
INFORMATION PROVIDED ON THIS DRAWING DOCUMENT ARE VITAL TO THE
CUSTOMER AND MFR MANUFACTURING CORPORATION, INC.. THE PRODUCTION OF
THE COMPONENTS ARE DEPENDENT UPON THE ACCURACY OF INFORMATION
PROVIDED TO MFR MANUFACTURING CORPORATION, INC. BY THE CUSTOMER. PLEASE
REVIEW THE MEASUREMENTS IN THE DRAWINGS CAREFULLY, VERIFY THEM IN THE
FIELD, DISCUSS AND CHECK THEM WITH YOUR DESIGNER AND CONTRACTOR.
INDICATE NECESSARY CHANGES IN RED MARKS. UPON SIGNING THIS BOX, IT WILL
SUPERSEDE ALL SIGNED AND AFFIXED STAMPS USED BY THE CUSTOMER FOR THEIR
OWN PURPOSES AND OFFICE PROCEDURES. CHANGES AFTER APPROVAL MAY INCUR
ADDITIONAL COSTS AND DELAYS IN PRODUCTION. FAILURE OF CUSTOMER TO COMPLY
WITH THIS REQUEST RELIEVES MFR OF ANY RESPONSIBILITY RESULTING FROM
ANY ERROR.
THESE DRAWINGS IN DESIGN AND DETAIL ARE THE SOLE
PROPERTY OF MFR MANUFACTURING CORPORATION, INC. AND MAY NOT BE USED
FOR ANY PURPOSE WHATSOEVER OTHER THAN FOR OUR MANUFACTURING FACILITY
AND INSTALLATION OF OUR PRODUCTS. THESE DOCUMENTS OR ANY PART THEREOF
MAY NOT BE REPRODUCED IN ANY MANNER WHATSOEVER AND SHALL BE RETURNED
TO US UPON REQUEST.
ALL RIGHTS RESERVED.
1) CUSTOMER WILL SPECIFY, APPROVE, VERIFY IN FIELD, AND GUARANTEE ALL DIMENSIONS SHOWN ON THESE DRAWINGS BEFORE FABRICATION.
REQUIRED ARCHITECTURAL DIMENSIONS OF FENCES, RAILINGS AND SCREENS PROVIDED BY CUSTOMER.
THEY SHOULD MEET ALL THE APPLICABLE BUILDING CODES REQUIRED BY LOCAL, STATE & OTHER REGULATORY AGENCIES.
2)
UNLESS OTHERWISE INDICATED IN THE PLAN, ALL MECHANICAL FASTENERS ARE TO BE SUPPLIED BY AND RESPONSIBILITY OF THE INSTALLER.3) MFR MANUFACTURING CORPORATION, INC. ASSUMES NO RESPONSIBILITY FOR THE DESIGN, CONSTRUCTION OR INSTALLATION OF ANY MATERIALS SUPPLIED BY OTHERS.4) ANY ADDITIONAL STRUCTURAL MEMBERS SUCH AS GUSSETS, BRACES, KICKERS, EMBEDS AND STIFFENERS, THAT MAY BE REQUIRED
ARE NOT THE RESPONSIBILITY OF MFR MANUFACTURING CORPORATION, INC.
5)
ACCIDENTAL DAMAGES & DEFECTS RESULTING FROM IMPROPER INSTALLATION AND VANDALISM ARE NOT COVERED UNDER THE WARRANTY
PROVIDED BY MFR MANUFACTURING CORPORATION, INC.
6)
ANY CLOUDED AREA IN THE DRAWING MUST BE REVIEWED. ADVISE MFR MANUFACTURING CORPORATION, INC. IN WRITING OF THE SUGGESTIONS OR BY REDLINING AND SIGNING THE DRAWINGS WITH THE ALTERNATIVE SOLUTIONS OR OPTIONS REGARDING THE MATTER.
7)
ALL THE SURROUNDING STEEL, CONCRETE, CMU, PRECAST STRUCTURES, SUPPORT, FRAMES, COLUMNS OR POSTS MUST BE DESIGNED
TO WITHSTAND ALL RESULTANT FORCES TRANSMITTED BY THE PANEL SCREENS AND RAILINGS.
8)
9)
ALL OF THE ELEVATIONS AND DETAILS DRAWN ILLUSTRATE WELDED ROD ON THE NEARSIDE, EXCEPT WHEN NOTED OTHERWISE.10) DIMENSION ALLOWANCE ON FABRICATION TOLERANCE IS +/- 1/4" (+/- 5mm) ON ALL DIMENSIONS.11)
THE MESH DRAWN BY HATCHES ARE SHOWN FOR ILLUSTRATION INTENT ONLY. DO NOT SCALE NOR MEASURE THE MESHES.
MESH SPACINGS ARE SPECIFIED ON THE ISOMETRIC (OR 2-D) PANEL DRAWING SHOWN ON THE UPPER RIGHT HAND SIDE OF THE SHEET.
ALIGNMENT OF MESHES ON SLOPED AND STRAIGHT PANELS MAY VARY DUE TO FIELD CONDITIONS AND SOME FACTORS ENCOUNTERED IN THE FIELD SUCH AS, BUT NOT LIMITED TO, CONSTRUCTION ERRORS, MISFITS, OR IRREGULARITIES.
MFR RESERVES THE RIGHT TO MAKE MINOR CHANGES AND ADJUSTMENTS IN ORDER TO ACCOMMODATE PRODUCTION AND MACHINE LIMITATIONS. THESE CHANGES WILL NOT IMPACT THE FUNCTION, ORIGINAL DESIGN INTENT OR OVERALL APPEARANCE.
12)
GENERAL NOTES
SOME FIELD MODIFICATIONS AND WELDING MAY BE REQUIRED.13)
4"x4" ALUMINUM MESH ISOMETRIC DETAIL
ALL HARDWARE INCLUDING FASTENERS, BOLTS, SCREWS, WASHERS, AND SIMILAR ITEMS ARE UNFINISHED AND USUALLY APPEAR AS ZINC-PLATED, GALVANIZED, OR CHROME-PLATED COLOR UNLESS OTHERWISE NOTED IN DRAWINGS
14)
4' SQ. ALUMINUM FENCE PANEL DETAIL
PANEL CONNECTION DETAIL
4/1/2025
AutoCAD SHX Text
14" ALUMINUM ROD TYPICAL
AutoCAD SHX Text 14" ALUMINUM ROD MESH 4"x4" OPENING SIZE ROD ENDS CAPTURED IN FRAME WELDED TO FRAME
AutoCAD SHX Text 2"x2"x " ALUMINUM TUBE 18" ALUMINUM TUBE PANEL FRAME
AutoCAD SHX Text 2 "x2"x " ALUMINUM PANEL ATTACHMENT TABS 14"x2"x " ALUMINUM PANEL ATTACHMENT TABS 14" ALUMINUM PANEL ATTACHMENT TABS WELDED TO BACK FACE OF FRAME HARDWARE/ANCHORS BY OTHERS
AutoCAD SHX Text
EXTERIOR
AutoCAD SHX Text
14" THK AL PLATE
AutoCAD SHX Text
CONTENTS:
AutoCAD SHX Text
PROJECT:
AutoCAD SHX Text
ADDRESS:
AutoCAD SHX Text
MASTER SHEET, ELEVATION, BILL OF MATERIAL, DETAIL & CHART
AutoCAD SHX Text
SCALE:
AutoCAD SHX Text
AutoCAD SHX Text A1
AutoCAD SHX Text 3" = 1'-0"
AutoCAD SHX Text A1
AutoCAD SHX Text
SCALE:
AutoCAD SHX Text
AutoCAD SHX Text A1
AutoCAD SHX Text 1-1/2" = 1'-0"
AutoCAD SHX Text
SCALE:
AutoCAD SHX Text
AutoCAD SHX Text A1
AutoCAD SHX Text 6" = 1'-0" amayo Received
File details come from the government source that posted it. Updated .