3-Z Asbestos Survey - 1904 E. Santa Fe St. - 02237230.pdf

Facilities | Environmental | Geotechnical | Materials I

City of Olathe Public Improvements

Asbestos Survey

Hertz Rental Car

1904 East Santa Fe Street

Olathe, Kansas 66062

June 27, 2025 | Terracon Project Number: 02237230

Prepared for:

City of Olathe Kansas

100 East Santa Fe Street

Olathe, KS 66061

15620 W 113th Street

Lenexa, KS 66219

P (913) 492-7777

F (913) 492-7443

Terracon.com

Facilities | Environmental | Geotechnical | Materials i

June 27, 2025

City of Olathe, Kansas

100 East Santa Fe Street

Olathe, KS 66061

Attn: Ms. Therese Vink

P: (913) 971-9032

E: tmersmann@olatheks.org

Re: City of Olathe Public Improvements Asbestos Survey

Hertz Rental Car

1904 East Santa Fe Street

Olathe, Kansas 66062

Terracon Project No: 02237230

Dear Ms. Vink:

Terracon Consultants, Inc. (Terracon) is pleased to provide the City of Olathe, Kansas, with this report regarding an asbestos survey conducted at the above-referenced location in Olathe, Kansas.

Asbestos

Asbestos was identified at a concentration greater than 1% in samples collected from the following materials:

Material Description Material Location

NESHAP

Category

Estimated

Quantity

Roofing Sealant

Upper Canopy - North and

South Perimeters; Car

Wash Roof Perimeter and

Vent Pipe

Category I

Nonfriable 318 Linear Feet

Notes: NESHAP – National Emission Standards for Hazardous Air Pollutants

City of Olathe Public Improvements Asbestos Survey

Hertz Rental Car | Olathe, Kansas

June 27, 2025 | Terracon Project No. 02237230

Facilities | Environmental | Geotechnical | Materials ii

Please refer to Section 3.0 of the attached report for a detailed description of the asbestos survey, sampling activities, and findings.

Terracon appreciates the opportunity to provide this service to the City of Olathe, Kansas. If you have any questions regarding this report, please contact our office at

913-492-7777.

Sincerely, Terracon

Ryan Slanczka Clark Grisell

Senior Staff Scientist Environmental Group Manager

Building Environmental Sciences

Ryan Slanczka Clark Grisell

Facilities | Environmental | Geotechnical | Materials iii

Table Of Contents

1.0 Introduction 1

1.1 Reliance 1

2.0 Building Description 1

3.0 Asbestos-Containing Materials Survey 1

3.1 Visual Assessment 2

3.2 Physical Assessment 2

3.3 Sample Collection 2

3.4 Sample Analysis 2

3.5 Regulatory Overview 3

3.6 Findings 3

4.0 General Comments 4

Appendices

Appendix A Asbestos-Containing Materials By Homogeneous Area

Appendix B Asbestos Survey Sample Location Summary

Appendix C Asbestos Laboratory Analytical Results

Appendix D Certifications

Facilities | Environmental | Geotechnical | Materials 1

1.0 Introduction

Terracon Consultants, Inc. (Terracon) conducted an asbestos-containing material survey of the Hertz Rental Car located at 1904 East Santa Fe Street in Olathe, Kansas, on May

30, 2025. Building areas were visually assessed for suspect asbestos-containing materials (ACM). A reasonable effort was made to inspect accessible areas. Additional suspect materials could be present in walls, voids, or other concealed areas.

1.1 Reliance

This report is for the exclusive use of the City of Olathe, Kansas, for the project being discussed. Reliance by any other party on this report is prohibited without the written authorization of Terracon and the City of Olathe, Kansas.

2.0 Building Description

The subject building is an approximately 576-square-foot, single-story, standalone store

(with exterior canopy), reportedly constructed in 1981. The site also includes a 665-square-foot car wash, reportedly constructed in 1989. Interior flooring finishes include ceramic tiles over concrete. Interior walls throughout the building are drywall/joint compound wallboard, with ceramic tile finishes in the restrooms. Perimeter walls throughout the building are concrete block. The primary, observable ceiling system is a drop, grid ceiling with lay-in acoustic tiles below a metal deck. The building’s exterior has brick and exterior insulation and finish system (EIFS) siding. The roof consists of a single-ply tar and gravel system.

3.0 Asbestos-Containing Materials Survey

The survey was conducted by Mr. Ryan Slanczka and Mr. Blake Harris, State of Kansas-accredited asbestos inspectors. Copies of the asbestos inspectors’ accreditations are attached as Appendix D. The survey was conducted in general accordance with the sample collection protocols established in the United States Environmental Protection

Agency (USEPA) 40 Code of Federal Regulations (CFR) Part 763 Subpart E 763.86, the

Asbestos Hazard Emergency Response Act (AHERA). A summary of survey activities is provided below.

Facilities | Environmental | Geotechnical | Materials 2

3.1 Visual Assessment

Survey activities were initiated with visual observation of the interior and exterior of the building to identify homogeneous areas of suspect ACM. A homogeneous area (HA) consists of a building material that appears similar throughout in terms of color and texture, with consideration given to the date of application. The assessment was conducted in visually accessible areas of the building scheduled for renovation.

3.2 Physical Assessment

A physical assessment of each HA of suspect ACM was conducted to assess the friability and condition of the materials. A friable material is defined by the USEPA as a material that can be crumbled, pulverized, or reduced to powder by hand pressure when dry.

Friability was assessed by physically touching suspect materials.

3.3 Sample Collection

Based on the results of the visual observation, bulk samples of suspect ACM samples were collected in general accordance with USEPA AHERA sampling protocols. Samples of suspect materials were collected from randomly selected locations in each homogeneous area. Bulk samples were collected using wet methods, as applicable, to reduce the potential for fiber release. Samples were placed in sealable containers and labeled with unique sample numbers using an indelible marker.

Rubber, wood products, plastic products, glass, and steel are not considered suspect

ACM and were, therefore, not sampled. The selection of sample locations and frequency of sampling were based on Terracon’s observations and the assumption that like materials in the same area are homogeneous in content. Terracon collected 45 bulk samples from 15 homogeneous areas of suspect ACM.

3.4 Sample Analysis

Bulk samples were submitted under chain of custody to Eurofins International Asbestos

Testing Laboratories (Eurofins) of Mount Laurel, New Jersey, for analysis by PLM with dispersion staining techniques per USEPA Method 600/R-93/116. The percentage of asbestos, where applicable, was determined by microscopic visual estimation. Eurofins is accredited under the National Voluntary Laboratory Accreditation Program (NVLAP), Accreditation No. 101165.

Facilities | Environmental | Geotechnical | Materials 3

3.5 Regulatory Overview

The asbestos National Emission Standards for Hazardous Air Pollutants (NESHAP) regulation (40 CFR Part 61, Subpart M) regulates asbestos fiber emissions and asbestos waste disposal practices. The asbestos NESHAP regulation also requires the identification and classification of existing ACM according to friability prior to demolition or renovation activity. Friable ACM is a material containing more than 1% asbestos that, when dry, can be crumbled, pulverized, or reduced to powder by hand pressure.

The asbestos NESHAP regulation classifies ACM as regulated asbestos-containing materials (RACM), Category I non-friable ACM, or Category II non-friable ACM. RACM includes all friable ACM; Category I non-friable ACM that has become friable or will be or has been subjected to sanding, grinding, cutting, or abrading; and Category II non-friable ACM that has a high probability of becoming or has become crumbled, pulverized, or reduced to powder in the course of renovation or demolition activity. Category I non-friable ACM are exclusively asbestos-containing packings, gaskets, resilient floor coverings, resilient floor covering mastics, and asphalt roofing products that contain more than 1% asbestos. Category II non-friable ACM are all other non-friable materials other than Category I non-friable ACM that contain more than 1% asbestos. Category II non-friable ACM generally includes but is not limited to cementitious material such as cement pipes, cement siding, cement panels, glazing, mortar, and grouts.

The Kansas Department of Health and Environment’s (KDHE) Asbestos Control Section within the Bureau of Air enforces the Asbestos NESHAP as adopted by reference at

Kansas Administrative Regulations (K.A.R.) 28-19-735. The owner or operator must provide KDHE with written notification at least 10 working days prior to the commencement of asbestos abatement activities that will disturb RACM in amounts greater than or equal to 10 square feet or 25 linear feet.

The United States Occupational Safety and Health Administration (USOSHA) asbestos standard for construction (29 CFR 1926.1101) regulates workplace exposure to asbestos. The OSHA standard classifies construction and maintenance activities that could disturb ACM and specifies work practices and precautions that employers must follow when engaging in each class of regulated work. The standard also specifies requirements for handling materials containing asbestos in concentrations less than or equal to one percent.

3.6 Findings

Asbestos was identified at a concentration greater than 1% in samples collected from the following materials:

Facilities | Environmental | Geotechnical | Materials 4

Material Description Material Location

NESHAP

Category

Estimated

Quantity

Roofing Sealant

Upper Canopy - North and

South Perimeters; Car

Wash Roof Perimeter and

Vent Pipe

Category I

Nonfriable 318 Linear Feet

Notes: NESHAP – National Emission Standards for Hazardous Air Pollutants

The above-listed Category I non-friable ACM that is damaged or could be damaged to the extent that it could be crumbled, pulverized, or reduced to powder when dry, making it friable, must be removed prior to any activities (renovation and/or demolition) that may disturb this material in accordance with applicable federal, state, and local regulations. Terracon recommends that all ACM be removed by an abatement contractor prior to any demolition or renovation work that may disturb it.

Asbestos was not detected at a concentration of 1% or less in any samples collected from the subject building.

A summary of identified asbestos-containing materials by homogeneous area is included in Appendix A. A summary of sample locations is included in Appendix B. Laboratory analytical reports are included in Appendix C.

4.0 General Comments

Terracon did not perform sampling that required demolition or destructive activities such as dismantling of equipment or removal of protective coverings. Reasonable efforts to access suspect materials within known areas of restricted access (e.g., crawl spaces) were made; however, confined spaces or areas that may pose a health or safety risk to

Terracon personnel were not sampled. Sampling did not include suspect materials that could not be safely reached with available ladders or manlifts. Terracon did not sample suspect materials that may be present in movable equipment such as freezers, kitchen equipment, and hoods. Terracon typically investigates for flooring beneath carpeting by lifting small corner sections of carpet. If tiles or sheet vinyl were seen, they have been identified in the report. If tiles or sheet vinyl were not seen at corners under the carpet, it does not imply that there is none beneath the carpeted floor. Terracon did not conduct a destructive investigation of the doors in the building to determine if the doors were insulated for fire-rating purposes.

This survey was conducted in a manner consistent with the level of care and skill ordinarily exercised by members of the profession currently practicing under similar conditions in the same locale. The results, findings, conclusions, and recommendations expressed in this report are based on conditions observed during Terracon’s survey of the building. The information contained in this report is relevant to the date on which

Facilities | Environmental | Geotechnical | Materials 5 this survey was performed, and should not be relied upon to represent conditions at a later date. This report has been prepared on behalf of and exclusively for use by the City of Olathe, Kansas, and is not a bidding document. Contractors or consultants reviewing this report must draw their own conclusions regarding further investigation or remediation deemed necessary. Terracon does not warrant the work of regulatory agencies, laboratories, or other third parties supplying information that may have been used in the preparation of this report. No warranty, express or implied, is made.

Appendix A

Asbestos-Containing Materials By Homogeneous Area

Appendix A

Identified Asbestos-Containing Materials By Homogeneous Area (HA)

1904 East Santa Fe Street, Olathe, Kansas

Terracon Project No. 02237230

HA Material Description Material Location % and Type

Asbestos*

NESHAP

Classification Condition

Estimated

Quantity**

15 Roofing Sealant

Upper Canopy - North and South Perimeters;

Car Wash Roof Perimeter and Vent Pipe

Black Sealant - 15%

Chrysotile

Category I

Nonfriable Good

Linear Feet

*% & Type Asbestos – this column contains both the analytical result of the sample with the highest concentration of asbestos detected in the samples that make up the HA, and the types of asbestos identified.

**Estimated quantities – quantities based on a cursory field evaluation, and actual quantities may vary significantly, especially if asbestos-containing materials are present in hidden and/or inaccessible areas not evaluated as part of this survey. This is not a bidding document; contractors are responsible for determining their own opinion of quantities.

Appendix B

Asbestos Survey Sample Location Summary

Appendix B

Asbestos Survey Sample Location Summary

1904 East Santa Fe Street, Olathe, Kansas

Terracon Project No. 02237230

HA

No.

Material Description

Sample

Number Sample Location Sample Layer Description Lab Results

1 Drywall with Joint Compound

01-WB5-01 NW Room, Ceiling

White Drywall with Brown Paper

None Detected

White Joint Compound

01-WB5-02 Central Room, South Wall

White Drywall with Brown Paper

White Joint Compound

01-WB5-03 South Room, South Wall

White Drywall with Brown Paper

White Joint Compound

2' x 2' Ceiling Tile with Pinholes and Divots

02-CT3-04 Central Room, Central Area White Ceiling Tile

None Detected 02-CT3-05 South Room, North Area White Ceiling Tile

02-CT3-06 South Room, South Area White Ceiling Tile

2' x 2' Ceiling Tile with Pinholes and Fissures

03-CT3-07 Central Room, South Area White Ceiling Tile

None Detected 03-CT3-08 Central Room, Central Area White Ceiling Tile

03-CT3-09 South Room, South Area White Ceiling Tile

4" x 4" Tan Ceramic Wall Tile with Adhesive and Grout 04-MA5-10 NW Room, West Wall

Tan Ceramic Tile

None Detected Yellow Adhesive

White Grout

Material Description

Sample

Number Sample Location Sample Layer Description Lab Results

4" x 4" Tan Ceramic Wall Tile with Adhesive and Grout

04-MA5-11 NW Room, North Wall

Tan Ceramic Tile

None Detected

Yellow Adhesive

White Grout

04-MA5-12 NW Room, East Wall

Tan Ceramic Tile

Yellow Adhesive

White Grout

12" x 12" Grey with Spots

Ceramic Floor Tile with Grout and Mortar

05-MA5-13 Central Room, West Area

Grey Ceramic Tile

None Detected

Grey Grout

White Mortar

05-MA5-14 South Room, North Area

Grey Ceramic Tile

Grey Grout

White Mortar

05-MA5-15 South Room, South Area

Grey Ceramic Tile

Grey Grout

White Mortar

12" x 12" Tan Ceramic Floor

Tile with Grout and Mortar 06-MA5-16 NW Room

Tan Ceramic Tile

None Detected Dark Grey Grout

Light Grey Mortar

Material Description

Sample

Number Sample Location Sample Layer Description Lab Results

12" x 12" Tan Ceramic Floor

Tile with Grout and Mortar

06-MA5-17 NW Room

Tan Ceramic Tile

None Detected

Dark Grey Grout

Light Grey Mortar

06-MA5-18 NW Room

Tan Ceramic Tile

Dark Grey Grout

Light Grey Mortar

8" x 8" Ceramic Floor Tile with

Grout and Mortar

07-MA5-19 NE Room

White/Brown Ceramic Tile

None Detected

Black Grout

Grey Mortar

07-MA5-20 NE Room

White/Brown Ceramic Tile

Black Grout

Grey Mortar

07-MA5-21 NE Room

White/Brown Ceramic Tile

Black Grout

Grey Mortar

Batt Insulation with Paper

Backing

08-AW1-22 South Room, SW Area

Tan/Black Tar Paper

None Detected

Pink Insulation

08-AW1-23 South Room, SW Area

Tan/Black Tar Paper

Pink Insulation

Material Description

Sample

Number Sample Location Sample Layer Description Lab Results

Batt Insulation with Paper

Backing 08-AW1-24 South Room, SW Area

Tan/Black Tar Paper

None Detected

Pink Insulation

9 CMU Mortar

09-MA2-25 NW Room, West Wall Grey Mortar

None Detected 09-MA2-26 Central Room, North Wall Grey Mortar

09-MA2-27 South Room, South Wall Grey Mortar

10 Brick Mortar

10-MA1-28 East Exterior, near Door Grey Mortar

None Detected 10-MA1-29 North Exterior, near NE Door Grey Mortar

10-MA1-30 West Exterior, near Door Grey Mortar

11 EIFS Siding

11-MS7-31 East Exterior, near Door Grey Cementitious Material

Insulation System (EIFS)

None Detected 11-MS7-32 North Exterior, Central Area Grey Cementitious Material

Insulation System (EIFS)

11-MS7-33 West Exterior, North Area Grey Cementitious Material

Insulation System (EIFS)

12 Door Caulk

12-CA2-34 North Exterior, NE Door Off-White Caulk with Black Paint

None Detected 12-CA2-35 North Exterior, NE Door Off-White Caulk with Black Paint

12-CA2-36 North Exterior, NW Door Off-White Caulk with Black Paint

13 Expansion Joint

13-MS5-37 South Exterior, East Area Black Expansion Joint

None Detected 13-MS5-38 South Exterior, Central Area Black Expansion Joint

13-MS5-39 South Exterior, West Area Black Expansion Joint

14 Roofing Material 14-RF5-40 Roof, West-Central Area

Black Tar with Rocks

None Detected

Black Tar Paper

Material Description

Sample

Number Sample Location Sample Layer Description Lab Results

14 Roofing Material

14-RF5-41 Roof, East-Central Area

Black Tar with Rocks

None Detected

Black Tar Paper

14-RF5-42 Roof, North Area, at Vent

Black Tar with Rocks

Black Tar Paper

15 Roofing Sealant

15-RF4-43

Upper Canopy, North Perimeter, Central Area Black Sealant 15% Chrysotile

15-RF4-44

Upper Canopy, South Perimeter, Central Area Black Sealant 15% Chrysotile

15-RF4-45 Carwash Roof, on Vent Pipe Black Sealant 10% Chrysotile

Asbestos-containing materials in BOLD.

Appendix C

Asbestos Laboratory Analytical Results

Approved by:

Approved Signatory Frank Ehrenfeld

Report for:

Ryan Slanczka Terracon Consultants- Lenexa 15620 W. 113th St Lenexa, KS 66219

Regarding:

Eurofins Built Environment Testing East, LLC Project: 02237230.14.2 - 1904 E Santa Fe St

EML ID: 4095650

All samples were received in acceptable condition unless noted in the Report Comments portion in the body of the report. The results relate only to the samples as received and tested. The results include an inherent uncertainty of measurement associated with estimating percentages by polarized light microscopy. Measurement uncertainty data for sample results with >1% asbestos concentration can be provided when requested.

Eurofins Built Environment Testing East, LLC ("the Company"), a member of the Eurofins Built Environment Testing group of companies, shall have no liability to the client or the client's customer with respect to decisions or recommendations made, actions taken or courses of conduct implemented by either the client or the client's customer as a result of or based upon the Test Results. In no event shall the Company be liable to the client with respect to the Test Results except for the Company's own willful misconduct or gross negligence nor shall the Company be liable for incidental or consequential damages or lost profits or revenues to the fullest extent such liability may be disclaimed by law, even if the Company has been advised of the possibility of such damages, lost profits or lost revenues. In no event shall the Company's liability with respect to the Test Results exceed the amount paid to the Company by the client therefor.

Dates of Analysis:

Asbestos PLM (Layer %): 06-10-2025

Service SOPs: Asbestos PLM (Layer %) (EPA 40CFR App E to Sub E of Part 763 & EPA METHOD 600/R-93-116, SOP EB-AS-S- 1267) NVLAP Lab Code 101165-0

EMLab ID: 4095650, Page 1 of 10Eurofins Built Environment Testing East, LLC

Eurofins Built Environment Testing East, LLC 9000 Commerce Parkway, Suite B, Mount Laurel, NJ 08054

(856) 231-9449 www.eurofinsus.com/Built Client: Terracon Consultants- Lenexa C/O: Ryan Slanczka Re: 02237230.14.2 - 1904 E Santa Fe St

Date of Receipt: 06-03-2025 Date of Report: 06-10-2025

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM) Appx E Sub E 40 CFR 763 / EPA 600/R-93/116

Sample ID # Lab-ID version Sample Description Asbestos

Constituents Non-Asbestos Constituents Comment

01-WB5-01. Drywall with Joint Compound; NW Room, Ceiling 20428036-1

Layer 1 White Drywall with Brown Paper Homogeneity:Good

Not Detected 90% Non-Fibrous Material 10% Cellulose

Layer 2 White Joint Compound Homogeneity:Good

Not Detected 100% Non-Fibrous Material

01-WB5-02. Drywall with Joint Compound; Central Room, South Wall 20428037-1

Layer 1 White Drywall with Brown Paper Homogeneity:Good

Homogeneity:Good

Not Detected 100% Non-Fibrous Material

01-WB5-03. Drywall with Joint Compound; South Room, South Wall 20428038-1

Layer 1 White Drywall with Brown Paper Homogeneity:Good

Homogeneity:Good

Not Detected 100% Non-Fibrous Material

02-CT3-04. 2'x2' Ceiling Tile with Pinhole and Divots; Central Room, Central Area 20428039-1

Layer 1 White Ceiling Tile Homogeneity:Good

Not Detected 60% Cellulose 30% Glass Fibers 10% Non-Fibrous Material

02-CT3-05. 2'x2' Ceiling Tile with Pinhole and Divots; South Room, North Area 20428040-1

Layer 1 White Ceiling Tile Homogeneity:Good

Not Detected 60% Cellulose

02-CT3-06. 2'x2' Ceiling Tile with Pinhole and Divots; South Room, South Area 20428041-1

Layer 1 White Ceiling Tile Homogeneity:Good

Not Detected 60% Cellulose

03-CT3-07. 2'x2' Ceiling Tile with Pinhole and Fissures; Central Room, South Area 20428042-1

Layer 1 White Ceiling Tile Homogeneity:Good

Not Detected 60% Cellulose

03-CT3-08. 2'x2' Ceiling Tile with Pinhole and Fissures; Central Room, Central Area 20428043-1

Layer 1 White Ceiling Tile Homogeneity:Good

Not Detected 60% Cellulose

03-CT3-09. 2'x2' Ceiling Tile with Pinhole and Fissures; South Room, South Area 20428044-1

Layer 1 White Ceiling Tile Homogeneity:Good

Not Detected 60% Cellulose

Comments:

EMLab ID: 4095650, Page 2 of 10Eurofins Built Environment Testing East, LLC

The total percentage of sample components shown may be greater than 100% when some components are detected at <1%.

The test report shall not be reproduced except in full, without written approval of the laboratory. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. The Company reserves the right to dispose of all samples after a period of thirty (30) days, according to all state and federal guidelines, unless otherwise specified.

Inhomogeneous samples are separated into homogeneous subsamples and analyzed individually. ND means no fibers of that type were detected.

When detected, the minimum detection and reporting limit is less than 1% unless point counting is performed. Floor tile samples may contain large amounts of interference material and it is recommended that the sample be analyzed by gravimetric point count analysis to lower the detection limit and to aid in asbestos identification.

‡ A "Version" indicated by -"x" after the Lab ID# with a value greater than 1 indicates a sample with amended data. The revision number is reflected by the value of "x".

(856) 231-9449 www.eurofinsus.com/Built Client: Terracon Consultants- Lenexa C/O: Ryan Slanczka Re: 02237230.14.2 - 1904 E Santa Fe St

Date of Receipt: 06-03-2025 Date of Report: 06-10-2025

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM) Appx E Sub E 40 CFR 763 / EPA 600/R-93/116

Sample ID # Lab-ID version Sample Description Asbestos

Constituents Non-Asbestos Constituents Comment

04-MA5-10. 4"x4" Tan Ceramic Wall Tile with Adhesive and Grout; NW Room, West Wall 20428045-1

Layer 1 Tan Ceramic Tile Homogeneity:Good

Not Detected 100% Non-Fibrous Material

Yellow Adhesive

Layer 3

Homogeneity:Good

Not Detected 100% Non-Fibrous Material

04-MA5-11. 4"x4" Tan Ceramic Wall Tile with Adhesive and Grout; NW Room, North Wall 20428046-1

Layer 1 Tan Ceramic Tile

Homogeneity:Good

Not Detected 100% Non-Fibrous Material

04-MA5-12. 4"x4" Tan Ceramic Wall Tile with Adhesive and Grout; NW Room, East Wall 20428047-1

Layer 1 Tan Ceramic Tile

Homogeneity:Good

Not Detected 100% Non-Fibrous Material

Comments:

EMLab ID: 4095650, Page 3 of 10Eurofins Built Environment Testing East, LLC

The total percentage of sample components shown may be greater than 100% when some components are detected at <1%.

The test report shall not be reproduced except in full, without written approval of the laboratory. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. The Company reserves the right to dispose of all samples after a period of thirty (30) days, according to all state and federal guidelines, unless otherwise specified.

Inhomogeneous samples are separated into homogeneous subsamples and analyzed individually. ND means no fibers of that type were detected.

When detected, the minimum detection and reporting limit is less than 1% unless point counting is performed. Floor tile samples may contain large amounts of interference material and it is recommended that the sample be analyzed by gravimetric point count analysis to lower the detection limit and to aid in asbestos identification.

‡ A "Version" indicated by -"x" after the Lab ID# with a value greater than 1 indicates a sample with amended data. The revision number is

(856) 231-9449 www.eurofinsus.com/Built Client: Terracon Consultants- Lenexa C/O: Ryan Slanczka Re: 02237230.14.2 - 1904 E Santa Fe St

Date of Receipt: 06-03-2025 Date of Report: 06-10-2025

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM) Appx E Sub E 40 CFR 763 / EPA 600/R-93/116

Sample ID # Lab-ID version Sample Description Asbestos

Constituents Non-Asbestos Constituents Comment

05-MA5-13. 12"x12" Grey with Spots Ceramic Floor Tile with Grout and Mortar; Central Room, West Area 20428048-1(cont.)

Layer 1 Gray Ceramic Tile

Gray Grout

White Mortar Homogeneity:Good

Not Detected 100% Non-Fibrous Material

05-MA5-14. 12"x12" Grey with Spots Ceramic Floor Tile with Grout and Mortar; South Room, North Area 20428049-1

Layer 1 Gray Ceramic Tile

Homogeneity:Good

Not Detected 100% Non-Fibrous Material

05-MA5-15. 12"x12" Grey with Spots Ceramic Floor Tile with Grout and Mortar; South Room, South Area 20428050-1

Layer 1 Gray Ceramic Tile

Homogeneity:Good

Not Detected 100% Non-Fibrous Material

Comments:

EMLab ID: 4095650, Page 4 of 10Eurofins Built Environment Testing East, LLC

The total percentage of sample components shown may be greater than 100% when some components are detected at <1%.

The test report shall not be reproduced except in full, without written approval of the laboratory. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. The Company reserves the right to dispose of all samples after a period of thirty (30) days, according to all state and federal guidelines, unless otherwise specified.

Inhomogeneous samples are separated into homogeneous subsamples and analyzed individually. ND means no fibers of that type were detected.

When detected, the minimum detection and reporting limit is less than 1% unless point counting is performed. Floor tile samples may contain large amounts of interference material and it is recommended that the sample be analyzed by gravimetric point count analysis to lower the detection limit and to aid in asbestos identification.

‡ A "Version" indicated by -"x" after the Lab ID# with a value greater than 1 indicates a sample with amended data. The revision number is

(856) 231-9449 www.eurofinsus.com/Built Client: Terracon Consultants- Lenexa C/O: Ryan Slanczka Re: 02237230.14.2 - 1904 E Santa Fe St

Date of Receipt: 06-03-2025 Date of Report: 06-10-2025

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM) Appx E Sub E 40 CFR 763 / EPA 600/R-93/116

Sample ID # Lab-ID version Sample Description Asbestos

Constituents Non-Asbestos Constituents Comment

06-MA5-16. 12"x12" Tan Ceramic Floor Tile with Grout and Mortar; NW Room 20428052-1(cont.)

Layer 1 Tan Ceramic Tile

Dark Gray Grout

Light Gray Mortar Homogeneity:Good

Not Detected 100% Non-Fibrous Material

06-MA5-17. 12"x12" Tan Ceramic Floor Tile with Grout and Mortar; NW Room 20428053-1

Layer 1 Tan Ceramic Tile

Homogeneity:Good

Not Detected 100% Non-Fibrous Material

06-MA5-18. 12"x12" Tan Ceramic Floor Tile with Grout and Mortar; NW Room 20428054-1

Layer 1 Tan Ceramic Tile

Homogeneity:Good

Not Detected 100% Non-Fibrous Material

Comments:

EMLab ID: 4095650, Page 5 of 10Eurofins Built Environment Testing East, LLC

The total percentage of sample components shown may be greater than 100% when some components are detected at <1%.

The test report shall not be reproduced except in full, without written approval of the laboratory. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. The Company reserves the right to dispose of all samples after a period of thirty (30) days, according to all state and federal guidelines, unless otherwise specified.

Inhomogeneous samples are separated into homogeneous subsamples and analyzed individually. ND means no fibers of that type were detected.

When detected, the minimum detection and reporting limit is less than 1% unless point counting is performed. Floor tile samples may contain large amounts of interference material and it is recommended that the sample be analyzed by gravimetric point count analysis to lower the detection limit and to aid in asbestos identification.

‡ A "Version" indicated by -"x" after the Lab ID# with a value greater than 1 indicates a sample with amended data. The revision number is

(856) 231-9449 www.eurofinsus.com/Built Client: Terracon Consultants- Lenexa C/O: Ryan Slanczka Re: 02237230.14.2 - 1904 E Santa Fe St

Date of Receipt: 06-03-2025 Date of Report: 06-10-2025

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM) Appx E Sub E 40 CFR 763 / EPA 600/R-93/116

Sample ID # Lab-ID version Sample Description Asbestos

Constituents Non-Asbestos Constituents Comment

07-MA5-19. 8"x8" Ceramic Floor Tile with Grout and Mortar; NE Room 20428055-1(cont.)

Layer 1 White/ Brown Ceramic Tile

Black Grout

Gray Mortar Homogeneity:Good

Not Detected 100% Non-Fibrous Material

07-MA5-20. 8"x8" Ceramic Floor Tile with Grout and Mortar; NE Room 20428056-1

Layer 1 White/ Brown Ceramic Tile

Homogeneity:Good

Not Detected 100% Non-Fibrous Material

07-MA5-21. 8"x8" Ceramic Floor Tile with Grout and Mortar; NE Room 20428057-1

Layer 1 White/ Brown Ceramic Tile

Homogeneity:Good

Not Detected 100% Non-Fibrous Material

Comments:

EMLab ID: 4095650, Page 6 of 10Eurofins Built Environment Testing East, LLC

The total percentage of sample components shown may be greater than 100% when some components are detected at <1%.

The test report shall not be reproduced except in full, without written approval of the laboratory. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. The Company reserves the right to dispose of all samples after a period of thirty (30) days, according to all state and federal guidelines, unless otherwise specified.

Inhomogeneous samples are separated into homogeneous subsamples and analyzed individually. ND means no fibers of that type were detected.

When detected, the minimum detection and reporting limit is less than 1% unless point counting is performed. Floor tile samples may contain large amounts of interference material and it is recommended that the sample be analyzed by gravimetric point count analysis to lower the detection limit and to aid in asbestos identification.

‡ A "Version" indicated by -"x" after the Lab ID# with a value greater than 1 indicates a sample with amended data. The revision number is

(856) 231-9449 www.eurofinsus.com/Built Client: Terracon Consultants- Lenexa C/O: Ryan Slanczka Re: 02237230.14.2 - 1904 E Santa Fe St

Date of Receipt: 06-03-2025 Date of Report: 06-10-2025

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM) Appx E Sub E 40 CFR 763 / EPA 600/R-93/116

Sample ID # Lab-ID version Sample Description Asbestos

Constituents Non-Asbestos Constituents Comment

08-AW1-22. Batt Insulation with Paper Backing; South Room, SW Area 20428058-1(cont.)

Layer 1 Tan/ Black Tar Paper Homogeneity:Good

Not Detected 60% Cellulose 40% Non-Fibrous Material

Homogeneity:Good

Not Detected 100% Glass Fibers

08-AW1-23. Batt Insulation with Paper Backing; South Room, SW Area 20428059-1

Layer 1 Tan/ Black Tar Paper Homogeneity:Good

Homogeneity:Good

Not Detected 100% Glass Fibers

08-AW1-24. Batt Insulation with Paper Backing; South Room, SW Area 20428060-1

Layer 1 Tan/ Black Tar Paper Homogeneity:Good

Homogeneity:Good

Not Detected 100% Glass Fibers

09-MA2-25. CMU Mortar; NW Room, West Wall 20428061-1

Layer 1 Gray Mortar Homogeneity:Good

Not Detected 100% Non-Fibrous Material

09-MA2-26. CMU Mortar; Central Room, North Wall 20428062-1

Layer 1 Gray Mortar Homogeneity:Good

Not Detected 100% Non-Fibrous Material

09-MA2-27. CMU Mortar; South Room, South Wall 20428063-1

Layer 1 Gray Mortar Homogeneity:Good

Not Detected 100% Non-Fibrous Material

10-MA1-28. Brick Mortar; East Exterior, near Door 20428064-1

Layer 1 Gray Mortar Homogeneity:Good

Not Detected 100% Non-Fibrous Material

10-MA1-29. Brick Mortar; North Exterior, near NE Door 20428065-1

Layer 1 Gray Mortar Homogeneity:Good

Not Detected 100% Non-Fibrous Material

10-MA1-30. Brick Mortar; West Exterior, near Door 20428066-1

Layer 1 Gray Mortar Homogeneity:Good

Not Detected 100% Non-Fibrous Material

11-MS7-31. EIFS Siding; East Exterior, near Door 20428067-1

Layer 1 Gray Cementitious Material Insulation System (EIFS) Homogeneity:Good

Not Detected 85% Non-Fibrous Material 15% Glass Fibers

EMLab ID: 4095650, Page 7 of 10Eurofins Built Environment Testing East, LLC

The total percentage of sample components shown may be greater than 100% when some components are detected at <1%.

The test report shall not be reproduced except in full, without written approval of the laboratory. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. The Company reserves the right to dispose of all samples after a period of thirty (30) days, according to all state and federal guidelines, unless otherwise specified.

Inhomogeneous samples are separated into homogeneous subsamples and analyzed individually. ND means no fibers of that type were detected.

When detected, the minimum detection and reporting limit is less than 1% unless point counting is performed. Floor tile samples may contain large amounts of interference material and it is recommended that the sample be analyzed by gravimetric point count analysis to lower the detection limit and to aid in asbestos identification.

‡ A "Version" indicated by -"x" after the Lab ID# with a value greater than 1 indicates a sample with amended data. The revision number is

(856) 231-9449 www.eurofinsus.com/Built Client: Terracon Consultants- Lenexa C/O: Ryan Slanczka Re: 02237230.14.2 - 1904 E Santa Fe St

Date of Receipt: 06-03-2025 Date of Report: 06-10-2025

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM) Appx E Sub E 40 CFR 763 / EPA 600/R-93/116

Sample ID # Lab-ID version Sample Description Asbestos

Constituents Non-Asbestos Constituents Comment

11-MS7-32. EIFS Siding; North Exterior, Central Area 20428068-1

Layer 1 Gray Cementitious Material Insulation System (EIFS) Homogeneity:Good

11-MS7-33. EIFS Siding; West Exterior, North Area 20428069-1

Layer 1 Gray Cementitious Material Insulation System (EIFS) Homogeneity:Good

12-CA2-34. Door Caulk; North Exterior, NE Door 20428070-1

Layer 1 Off-White Caulk w/ Black Paint Homogeneity:Good

Not Detected 100% Non-Fibrous Material

12-CA2-35. Door Caulk; North Exterior, NE Door 20428071-1

Layer 1 Off-White Caulk w/ Black Paint Homogeneity:Good

Not Detected 100% Non-Fibrous Material

12-CA2-36. Door Caulk; North Exterior, NW Door 20428072-1

Layer 1 Off-White Caulk w/ Black Paint Homogeneity:Good

Not Detected 100% Non-Fibrous Material

13-MS5-37. Expansion Joint; South Exterior, East Area 20428073-1

Layer 1 Black Expansion Joint Homogeneity:Good

Not Detected 75% Non-Fibrous Material 25% Cellulose

13-MS5-38. Expansion Joint; South Exterior, Central Area 20428074-1

Layer 1 Black Expansion Joint Homogeneity:Good

13-MS5-39. Expansion Joint; South Exterior, West Area 20428075-1

Layer 1 Black Expansion Joint Homogeneity:Good

14-RF5-40. Roofing Mateiral; Roof, West-Central Area 20428076-1

Layer 1 Black Tar w/ Rocks

Homogeneity:Good

Not Detected 80% Cellulose 20% Non-Fibrous Material

14-RF5-41. Roofing Mateiral; Roof, East-Central Area 20428077-1

Layer 1 Black Tar w/ Rocks

Homogeneity:Good

EMLab ID: 4095650, Page 8 of 10Eurofins Built Environment Testing East, LLC

The total percentage of sample components shown may be greater than 100% when some components are detected at <1%.

The test report shall not be reproduced except in full, without written approval of the laboratory. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. The Company reserves the right to dispose of all samples after a period of thirty (30) days, according to all state and federal guidelines, unless otherwise specified.

Inhomogeneous samples are separated into homogeneous subsamples and analyzed individually. ND means no fibers of that type were detected.

When detected, the minimum detection and reporting limit is less than 1% unless point counting is performed. Floor tile samples may contain large amounts of interference material and it is recommended that the sample be analyzed by gravimetric point count analysis to lower the detection limit and to aid in asbestos identification.

‡ A "Version" indicated by -"x" after the Lab ID# with a value greater than 1 indicates a sample with amended data. The revision number is

(856) 231-9449 www.eurofinsus.com/Built Client: Terracon Consultants- Lenexa C/O: Ryan Slanczka Re: 02237230.14.2 - 1904 E Santa Fe St

Date of Receipt: 06-03-2025 Date of Report: 06-10-2025

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM) Appx E Sub E 40 CFR 763 / EPA 600/R-93/116

Sample ID # Lab-ID version Sample Description Asbestos

Constituents Non-Asbestos Constituents Comment

14-RF5-42. Roofing Mateiral; Roof, North Area, at Vent 20428078-1(cont.)

Layer 1 Black Tar w/ Rocks

Homogeneity:Good

15-RF4-43. Roofing Sealant; Upper Canopy, North Perimeter, Central Area 20428079-1

Layer 1 Black Sealant Homogeneity:Good

15% Chrysotile 85% Non-Fibrous Material

15-RF4-44. Roofing Sealant; Upper Canopy, South Perimeter, Central Area 20428080-1

Layer 1 Black Sealant Homogeneity:Good

15% Chrysotile 85% Non-Fibrous Material

15-RF4-45. Roofing Sealant;

Carwash Roof, on Vent Pipe 20428081-1

Layer 1 Black Sealant Homogeneity:Good

10% Chrysotile 90% Non-Fibrous Material

Comments:

Analyst(s): Maxamillian Roselli

EMLab ID: 4095650, Page 9 of 10Eurofins Built Environment Testing East, LLC

The total percentage of sample components shown may be greater than 100% when some components are detected at <1%.

The test report shall not be reproduced except in full, without written approval of the laboratory. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. The Company reserves the right to dispose of all samples after a period of thirty (30) days, according to all state and federal guidelines, unless otherwise specified.

Inhomogeneous samples are separated into homogeneous subsamples and analyzed individually. ND means no fibers of that type were detected.

When detected, the minimum detection and reporting limit is less than 1% unless point counting is performed. Floor tile samples may contain large amounts of interference material and it is recommended that the sample be analyzed by gravimetric point count analysis to lower the detection limit and to aid in asbestos identification.

‡ A "Version" indicated by -"x" after the Lab ID# with a value greater than 1 indicates a sample with amended data. The revision number is

(856) 231-9449 www.eurofinsus.com/Built Client: Terracon Consultants- Lenexa C/O: Ryan Slanczka Re: 02237230.14.2 - 1904 E Santa Fe St

Date of Receipt: 06-03-2025 Date of Report: 06-10-2025

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM) Appx E Sub E 40 CFR 763 / EPA 600/R-93/116

PROJECT ANALYST AND SIGNATORY REPORT

Project Analyst

The test report shall not be reproduced except in full, without written approval of the laboratory. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. The Company reserves the right to dispose of all samples after a period of thirty (30) days, according to all state and federal guidelines, unless otherwise specified.

‡ A "Version" indicated by -"x" after the Lab ID# with a value greater than 1 indicates a sample with amended data. The revision number is reflected by the value of "x".

Analyst: Maxamillian Roselli

EMLab ID: 4095650, Page 10 of 10Eurofins Built Environment Testing East, LLC

Appendix D

Certifications

Certificate # 000MO31910324

Blake Harris has on 09/06/2024 completed the requirements for asbestos accreditation under

Section 206 of TSCA Title II, 15 USC 2646

Online Asbestos Building Inspector Refresher (4 Hour) as approved by MO and the US EPA under 40 CFR 763 (AHERA) and passed the associated exam on 09/06/2024 with a score of at least 70%.

SSN: XXX-XX-9521

Expiration: 09/06/2025

PO BOX 786 – Lawrence, KS 66044 – 800.444.6382 www.metaenvironmental.net