2026-06-02_SheradenPark_Alternates+ItemDescriptions.docx

Sheraden Park Phase I Improvements City of Pittsburgh Sheraden Park Phase I Improvements Bid Form Item Descriptions City of Pittsburgh, Allegheny County | Job No. 304 2202 | 02 June 2026 Alternates Add Alternate 1 – Tree Furnishing and Installation Including, but not limited to: Furnishing and installation of trees as identified on the Planting Plan Drawings (sheets L120–L124), in the event that City Forestry and TreePGH are unable to provide and install. Tree pit preparation by the General Contractor is included in the Base Bid under Item 51 regardless of whether this Alternate is awarded. This Alternate shall be awarded only upon written direction from the Owner. The following species and quantities are included under this Alternate:

Trees – 3" Caliper (Bid Form Item 1b)

1. Betula alleghaniensis (Yellow Birch) – 3" CAL. – 5 EA

1. Nyssa sylvatica (Black Gum) – 3" CAL. – 10 EA

1. Platanus occidentalis (American Sycamore) – 3" CAL. – 2 EA

1. Quercus alba (White Oak) – 3" CAL. – 19 EA Trees – 2½" Caliper (Bid Form Item 1a)

1. Amelanchier canadensis (Canadian Serviceberry) – 2½" CAL. – 7 EA

1. Alnus serrulata (Hazel Alder) – 2½" CAL. – 13 EA

1. Cercis canadensis (Eastern Redbud) – 2½" CAL. – 6 EA

1. Cornus florida (Flowering Dogwood) – 2½" CAL. – 3 EA

1. Malus domestica 'Gala' (Gala Apple) – 2½" CAL. – 2 EA

1. Malus domestica 'Honeycrisp' (Honeycrisp Apple) – 2½" CAL. – 2 EA

Bid Form Item Descriptions General Conditions Item No. 1: Mobilization / Demobilization / General Conditions Unit of Measurement: Lump Sum Description:

1. Mobilization to and demobilization from the project site

1. Setup of temporary facilities and equipment staging

1. Project management, supervision, survey and layout

1. Progress meetings, submittals, and record drawings

1. Project closeout

Item No. 2: Performance and Payment Bond Unit of Measurement: Lump Sum Description:

1. Furnishing of a Performance and Payment Bond as required by the Contract Documents

Item No. 3: Misc. General Conditions Unit of Measurement: Lump Sum Description:

1. All remaining general conditions scope not listed individually

1. Permits — Contractor to pick up all parent permits and apply for all subsequent permits required to complete the Work

1. Maintenance and traffic protection throughout the duration of construction

1. Temporary construction fence

1. E&S measures — installation, maintenance, inspection, and removal of all BMPs in accordance with the approved E&S plan

1. Tree protection fencing for all trees designated to remain

1. All other general condition costs required for a complete project

Demolition and Site Preparation Item No. 4: Remove Existing Trees Unit of Measurement: Each Description:

1. Felling, removal, and off-site disposal of existing trees as shown on the Contract Documents

1. Stump grinding to 6 inches below finished grade

1. Restoration of disturbed areas

Item No. 5: Remove Existing Electrical Equipment and Infrastructure Unit of Measurement: Lump Sum Description:

1. Removal and off-site disposal of all existing electrical equipment, conduit, wiring, panels, and associated infrastructure

1. Coordination with utility companies as required

1. Restoration of disturbed areas

Item No. 6: Demolish Asphalt and Subbase Unit of Measurement: Square Foot Description:

1. Saw cut, removal, and off-site disposal of existing asphalt paving and subbase material

1. Restoration of exposed subgrade to accept new construction

Item No. 7: Demolish Concrete and Subbase Unit of Measurement: Square Foot Description:

1. Saw cut, removal, and off-site disposal of existing concrete paving and subbase material

1. Restoration of exposed subgrade to accept new construction

Item No. 8: Demolish Play Surface, Subbase, and Surrounding Curb Unit of Measurement: Square Foot Description:

1. Removal and off-site disposal of existing playground safety surface, aggregate subbase, and surrounding concrete curb

1. Restoration of exposed subgrade to accept new construction

Item No. 9: Clear and Grub Unit of Measurement: Square Foot Description:

1. Removal and off-site disposal of all vegetation, brush, stumps, roots, and other organic material within the limits of work

1. Grubbing of root systems to a minimum of 12 inches below finished grade

Item No. 10: Misc. Demolition Unit of Measurement: Lump Sum Description:

1. All remaining demolition scope not listed individually

1. Remove existing concrete curb (72 LF), curb stops (9 EA), and guard rails and foundations (200 LF)

1. Remove existing light poles and foundations at sports field (4 EA)

1. Remove existing block building at sports field (145 SF) including foundations

1. Remove existing benches (14 EA), grill (1 EA), and water fountains with cut and cap of utilities (3 EA)

1. Remove existing play equipment and foundations (1 LS); owner to be given first opportunity to retain items prior to disposal

1. Remove existing pipe at ex. building (1 LS); cap active utilities and restore disturbed areas

1. Remove existing fence posts (14 EA) and fence bollards and foundations (10 EA)

1. Demolish existing stone surface (1,860 SF) and restore subgrade

Earthwork and Grading Item No. 11: Pavement Sawcut (24" Wide) Unit of Measurement: Linear Foot Description:

1. All labor, materials, and equipment required to sawcut existing pavement to a clean, smooth edge

1. Unit price applies to both initial sawcut and final restoration sawcut locations

Item No. 12: Remove Existing Chain Link Fence and Foundations Unit of Measurement: Linear Foot Description:

1. Removal and off-site disposal of existing chain link fence fabric, posts, rails, and concrete foundations

1. Backfill and restoration of disturbed areas

Item No. 13: Remove Existing Guide Rail and Foundations Unit of Measurement: Linear Foot Description:

1. Removal and off-site disposal of existing guide rail sections, posts, and foundations

1. Backfill and restoration of disturbed areas

Item No. 14: Rough Grading Unit of Measurement: Cubic Yard Description:

1. Unclassified excavation, grading, and earthmoving required to establish rough subgrade elevations

1. Stockpiling of suitable material for reuse as fill; off-site disposal of unsuitable material

1. Site-wide rough order of magnitude: approximately 3,500 CY cut and 2,000 CY fill

Item No. 15: Finish Grading Unit of Measurement: Cubic Yard Description:

1. Fine grading, trimming, and shaping required to establish finished grade elevations

1. Hand grading around structures

1. Fine grading of all planted, lawn, and seeded areas

Item No. 16: Haul / Import Soil Unit of Measurement: Cubic Yard Description:

1. Furnishing, hauling, transporting, and placing imported suitable fill material

1. Fill to be non-carbonaceous, non-pyritiferous, non-expansive, and non-slag material meeting Contract Document requirements

1. Cohesive fill compacted to minimum 95% of maximum standard Proctor dry density per ASTM D698

1. Granular fill compacted to at least 70% relative density per ASTM D4253 and D4254

Item No. 17: Misc. Trenching Unit of Measurement: Lump Sum Description:

1. All trenching scope not included under other line items

1. Trench for underdrains along walking trails and hillside areas (approx. 1,200 LF) — geotextile fabric, underdrain pipe and aggregate, backfill

1. Trench for potable water pipe serving drinking fountain (approx. 400 LF)

1. Trench for sewer drain pipe serving drinking fountain (approx. 400 LF)

1. All trench backfill, compaction, and surface restoration

1. Note: Electrical conduit trenching is included under Electrical (Item 24)

Concrete Item No. 18: 4" Concrete Paving and Subbase (Walkways) Unit of Measurement: Square Foot Description:

1. Furnish and install 4-inch thick concrete paving and aggregate subbase for pedestrian walkways

1. All excavation, subbase preparation, formwork, reinforcement, concrete placement, finishing, and curing

1. Application area approximately 4,090 SF

Item No. 19: Concrete Curb Unit of Measurement: Linear Foot Description:

1. Furnish and install concrete curb as shown on the Contract Documents

1. All excavation, subbase preparation, formwork, concrete placement, finishing, curing, and backfill

1. Approximately 25 LF

Item No. 20: Misc. Concrete Unit of Measurement: Lump Sum Description:

1. All remaining concrete scope not listed individually

1. Foundations for 25' City standard vehicular light poles (10 EA) per COP standard drawings

1. Foundations for Musco sport court lighting poles per Musco design requirements (3 EA)

1. Foundations for pickleball net posts (2 EA) and basketball hoop posts (2 EA)

1. Foundation for playground equipment — coordinate with Kompan; work by Others

1. 4" concrete pads and aggregate subbase for City benches (10 EA) and park benches (11 EA)

1. 16" reinforced concrete pad and aggregate subbase for drinking fountain (1 EA)

1. Detectable warning surfaces at all curb ramp locations in compliance with ADA standards (5 EA)

Plumbing Item No. 21: Potable Water Pipe (Drinking Fountain) Unit of Measurement: Linear Foot Description:

1. Furnish and install potable water supply piping from point of connection to drinking fountain

1. All excavation, pipe installation, fittings, valves, backfill, and pressure testing

1. Approximately 400 LF

Item No. 22: Sewer Drain Pipe (Drinking Fountain) Unit of Measurement: Linear Foot Description:

1. Furnish and install sewer drain piping from drinking fountain to point of connection

1. All excavation, pipe installation, fittings, cleanouts, backfill, and testing

1. Approximately 400 LF

Item No. 23: Plumbing Connection at Source (VIF) Unit of Measurement: Each Description:

1. All labor, materials, and equipment required to make final connections to existing water supply and sewer services

1. Actual connection location and depth to be verified in the field prior to construction

1. Unit price assumes 15-foot depth; actual cost subject to depth, tap location, and field conditions

1. Coordinate with PWSA as required

Electrical Item No. 24: Electrical Trench, Backfill, and Conduit Unit of Measurement: Linear Foot Description:

1. Trench excavation, PVC Schedule 40 conduit (1", 2", and 3" as applicable), traceable marker tape, select earth backfill, and surface restoration

1. Conduits under roadway to be installed a minimum of 30 inches below subbase

1. Approximately 2,374 LF

Item No. 25: City Standard Vehicular Light Pole and Fixture (25') Unit of Measurement: Each Description:

1. City of Pittsburgh standard 25-foot vehicular light poles and arm-mount LED luminaires

1. Lumec Road Focus RFM series, 2700K, integral photocell

1. Pole foundation (see Misc. Concrete, Item 20), installation, wiring connections, and testing

1. Installation in accordance with City of Pittsburgh standard drawings LPF-1, PF-1, LPF-2P, and CTY-3

1. 10 EA total

Item No. 26: Sport Court Lighting Pole and Fixture (Musco) Unit of Measurement: Each Description:

1. Musco TLC-LED-550 sport court lighting poles and luminaires at 30-foot mounting height

1. Musco-designed pole foundations; raising of poles and luminaires by Musco

1. Push button activators and amber strobe lights on poles P1 and P3

1. All wiring connections and commissioning for a complete and operational installation

1. 3 EA total — P1 (Basketball), P2 (Basketball/Pickleball), P3 (Pickleball)

Item No. 27: Misc. Electrical Unit of Measurement: Lump Sum Description:

1. All remaining electrical scope not listed individually

1. Junction boxes 24"x24" Type B (7 EA) — all excavation, setting, conduit connections, covers, and backfill

1. Musco lighting control panel, Panel SL (400A MLO, 120/240V, 1-phase, 3-wire), 225A enclosed circuit breaker, contactors, and 120V-48V control transformer

1. Removal of existing electrical equipment along northern interior wall: 300A lighting contactor, 225A MB panel, 60A disconnect

1. Coordination with Duquesne Light Company for service disconnections and connections

1. Replacement of existing electrical room luminaire with new LED vaportight surface mount fixture (Cooper Fail-Safe VRVTI-SL3C3-High Power-4000K or equivalent)

1. Electrical testing and inspections; ground resistance testing at all pole foundations (maximum 25 ohms per PADOT Form CS-4225A)

Exterior Improvements Item No. 28: Asphalt Paving and Subbase (Standard Duty) Unit of Measurement: Square Foot Description:

1. Standard duty asphalt paving and aggregate subbase

1. All subgrade preparation, proof-rolling, subbase placement and compaction, binder and surface course installation

1. Approximately 28,450 SF

Item No. 29: Asphalt Paving and Subbase (Heavy Duty) Unit of Measurement: Square Foot Description:

1. Heavy duty asphalt paving and aggregate subbase

1. All subgrade preparation, proof-rolling, subbase placement and compaction, binder and surface course installation

1. Approximately 15,275 SF

Item No. 30: Asphalt Wedge Curb Unit of Measurement: Linear Foot Description:

1. Furnish and install asphalt wedge curb including all subbase preparation

1. Approximately 960 LF

Item No. 31: Traffic Guide Rail Unit of Measurement: Linear Foot Description:

1. Furnish and install traffic guide rail including all posts, hardware, and end treatments

1. Installation in accordance with applicable standards and the Contract Documents

1. Approximately 340 LF

Item No. 32: Pavement Sawcut Restoration (24" Wide, Min.)

Unit of Measurement: Linear Foot Description:

1. Restore pavement at sawcut locations to match existing adjacent pavement cross section

1. Includes subbase repair, tack coat, and asphalt or concrete surface restoration as applicable

1. Approximately 155 LF

Item No. 33: Misc. Exterior Improvements Unit of Measurement: Lump Sum Description:

1. All remaining exterior improvements scope not listed individually

1. Crushed stone trail surface and aggregate subbase (approx. 525 SF)

1. Playground safety surfacing — pour-in-place rubber with 6" aggregate base (approx. 8,296 SF); by Others, Contractor to coordinate

1. Precast concrete wheel stops (46 EA)

1. ADA pavement markings — parking symbols, access aisle striping, and diagonal hatching

1. Parking lot striping, road striping, bicycle shared symbols, and crosswalk markings

1. Basketball and pickleball court markings (approx. 8,280 SF)

1. Repaint existing shelter roof and columns — surface preparation, priming, and finish coats in Owner-approved colors

1. Segmental retaining wall less than 4-ft height (approx. 105 LF) — all excavation, base prep, block installation, drainage aggregate, geotextile, cap units, and backfill

1. Metal landscape edging at garden and planting bed edges (approx. 160 LF)

1. 6' chain link fence at pickleball court (approx. 100 LF)

1. 10' chain link fence at basketball court (approx. 240 LF) and community gardens (approx. 160 LF)

1. 4' wide chain link fence gate at community garden enclosure (1 EA)

1. 4' ornamental metal fence (approx. 30 LF)

1. City standard outdoor grill (1 EA)

1. Raised garden beds (7 EA) and ADA-accessible garden planters (4 EA)

1. Engineered wood fiber mulch (EWF) to 6" compacted depth in playground areas (approx. 45 CY) per ASTM F1292

Site Furnishings and Equipment Item No. 34: Misc. Site Furnishings, Equipment, and Signage Unit of Measurement: Lump Sum Description:

1. All site furnishings, equipment, and signage scope

1. Trail wayfinding signage — post and foundation installation; sign panels by DPW (8 EA)

1. Park entrance sign — post and foundation installation; sign panel by DPW (1 EA)

1. Road signage attached to existing telephone poles (22 EA)

1. Pickleball net and post assembly (1 EA)

1. Basketball hoop, backboard, and post assembly (2 EA) — coordinate with concrete foundations under Item 20

1. Playground equipment (Kompan) — furnished and installed by Others; Contractor to coordinate for site preparation and installation schedule

1. 8'x10' garden shed (1 EA) — all site preparation, anchoring, and assembly

1. Bicycle racks — Dero triple (2 EA) per City of Pittsburgh standard details

1. Trash and recycling receptacles, paired (5 EA)

1. Park benches, frame only (12 EA) — coordinate with concrete pads under Item 20

1. Drinking fountain with potable water and sanitary drain connections (1 EA) — coordinate with plumbing under Items 21 and 22

1. Outdoor grill (1 EA)

1. Pipe bollards (18 EA) and collapsible bollards (6 EA)

1. Yard hydrant serving community garden area (1 EA)

1. PWSA taps and connections (2 EA; assumes 15-foot depth; subject to actual field conditions)

Stormwater Management Item No. 35: Piping – 12" HDPE Unit of Measurement: Linear Foot Description:

1. Furnish and install 12-inch diameter HDPE storm pipe

1. All excavation, pipe zone aggregate, pipe installation, backfill, compaction, and surface restoration

1. 316 LF

Item No. 36: Piping – 12" Perforated HDPE Unit of Measurement: Linear Foot Description:

1. Furnish and install 12-inch diameter perforated HDPE pipe

1. All excavation, geotextile fabric, pipe zone aggregate, pipe installation, geotextile fabric wrap, backfill, compaction, and surface restoration

1. Note: perforated HDPE requires geotextile wrapping and is priced separately from solid HDPE due to different installation requirements

1. 159 LF

Item No. 37: Piping – 15" SDR 26 PVC Unit of Measurement: Linear Foot Description:

1. Furnish and install 15-inch diameter SDR 26 PVC storm pipe

1. All excavation, pipe zone aggregate, pipe installation, backfill, compaction, and surface restoration

1. 118 LF

Item No. 38: Piping – 18" SDR 26 PVC Unit of Measurement: Linear Foot Description:

1. Furnish and install 18-inch diameter SDR 26 PVC storm pipe

1. All excavation, pipe zone aggregate, pipe installation, backfill, compaction, and surface restoration

1. 30 LF

Item No. 39: 4" SCH 40 PVC Underdrain Unit of Measurement: Linear Foot Description:

1. Furnish and install 4-inch Schedule 40 PVC underdrain pipe

1. All excavation, geotextile fabric, pipe zone aggregate, pipe installation, backfill, and surface restoration

1. Covers two applications: rain garden areas (approx. 210 LF) and trail and hillside areas (approx. 1,200 LF)

1. Total combined quantity: 1,410 LF

Item No. 40: Cleanout – 4" PVC Unit of Measurement: Each Description:

1. Furnish and install 4-inch PVC pipe cleanouts

1. All excavation, pipe connections, cleanout riser, cap, frame and cover as applicable, backfill, and surface restoration

1. 8 EA

Item No. 41: Type 'M' Inlet Unit of Measurement: Each Description:

1. Furnish and install Type M stormwater inlets

1. All excavation, pipe connections, precast or cast-in-place structure, frame and grate, backfill, and surface restoration

1. 4 EA

Item No. 42: Flared End Section Unit of Measurement: Each Description:

1. Furnish and install flared end section at pipe outlet

1. All excavation, pipe connections, riprap apron, backfill, and surface restoration

1. 1 EA

Item No. 43: Outlet Control Structures Unit of Measurement: Each Description:

1. Furnish and install outlet control structures

1. All excavation, precast or cast-in-place construction, pipe connections, weir or orifice plate as applicable, frame and cover, backfill, and surface restoration

1. 2 EA

Item No. 44: Yard Drain (2' x 2') Unit of Measurement: Each Description:

1. Furnish and install 2-foot by 2-foot yard drain structures

1. All excavation, pipe connections, grate, backfill, and surface restoration

1. 1 EA

Item No. 45: R-3 Riprap Unit of Measurement: Cubic Yard Description:

1. Furnish and install R-3 riprap at pipe outlets and other locations as shown on the Contract Documents

1. All excavation, geotextile fabric, stone placement, and grading

1. 3 CY

Item No. 46: Rain Garden Landscaping and BMPs Unit of Measurement: Lump Sum Description:

1. Construct rain garden areas and associated best management practices

1. All grading, soil amendment, underdrain installation, overflow structures, planting, and mulching

1. Installation in accordance with the Contract Documents

Item No. 47: Vegetated Channel with Infiltration Trench Unit of Measurement: Lump Sum Description:

1. Construct vegetated channel and infiltration trench

1. All excavation, geotextile, aggregate, underdrain installation, channel grading, and planting

1. Installation in accordance with the Contract Documents

Item No. 48: Soil Amendment (Haul In from Off-Site Source) Unit of Measurement: Cubic Yard Description:

1. Furnish, haul, and place soil amendment material from an approved off-site source

1. All testing, transport, placement, and incorporation required

1. Approximately 660 CY

Item No. 49: PWSA Taps and Connections Unit of Measurement: Each Description:

1. All labor, materials, and equipment required to make connections to Pittsburgh Water and Sewer Authority (PWSA) systems

1. Unit price assumes 15-foot depth; actual cost subject to depth, tap location, and conditions verified in the field

1. Coordinate all work with PWSA prior to construction

1. 2 EA

Item No. 50: Misc. Stormwater Unit of Measurement: Lump Sum Description:

1. All remaining stormwater scope not listed individually

1. Permanent storm inlet filters at stormwater inlets (5 EA)

1. Camera inspection and cleaning of existing storm inlets and piping — work by Others; formal proposal required; Contractor to coordinate scheduling with Owner and Engineer prior to construction

1. Any additional stormwater structures, connections, or appurtenances required for a complete installation as shown on the Contract Documents or as directed in the field

Landscaping Item No. 51: Tree Pit Preparation (All Calipers) — see Add Alternate 1 Unit of Measurement: Each Description:

1. All labor, materials, and equipment required to excavate and prepare tree pits for all caliper sizes

1. Covers 2½" CAL. trees (43 EA) and 3" CAL. trees (38 EA) as identified on the Planting Plan Drawings (sheets L120–L124); total 81 EA

1. Excavation to dimensions required by the Contract Documents, soil amendment, and backfill preparation

1. Coordinate with City Forestry or TreePGH for tree installation scheduling

1. Furnishing and installation of trees is by City Forestry or TreePGH; see Add Alternate 1 if furnishing and installation by the Contractor is required

Item No. 52: Shrub Planting (#5 Container) Unit of Measurement: Each Description:

1. Furnish and install #5 container shrubs as shown on the Planting Plan Drawings

1. All excavation, soil amendment, planting, mulching, and initial maintenance

1. 53 EA

Item No. 53: Topsoil (4" Depth; Lawn and Seed Mix Areas) Unit of Measurement: Cubic Yard Description:

1. Furnish and place topsoil to 4-inch depth in lawn and seed mix areas

1. All spreading, grading, and compaction required to achieve finished grade and prepare for seeding

1. Application area approximately 71,800 SF; approximately 900 CY

Item No. 54: Misc. Landscaping Unit of Measurement: Lump Sum Description:

1. All remaining landscaping scope not listed individually

1. Perennial and ornamental grass planting, #2 container (261 EA) — all excavation, soil amendment, planting, mulching, and initial maintenance

1. Steep slope meadow seed mix at 1.5 lb/1,000 SF (approx. 23,747 SF) per specification 329243

1. Pollinator meadow seed mix at 1.5 lb/1,000 SF (approx. 2,630 SF) per specification 329243

1. Rain garden seed mix at 1.0 lb/1,000 SF (approx. 2,200 SF) per specification 329243

1. Lawn seed mix at 5.0 lb/1,000 SF (approx. 43,000 SF)

1. Cover crops (grain oats/grain rye or other species by season) in pollinator meadow and rain garden seeding areas

1. Double-shredded wood mulch to 3-inch depth in planting beds (approx. 45 CY)

Add Alternate 1 – Unit Prices The following unit prices apply to Add Alternate 1 – Tree Furnishing and Installation, and are to be completed only in the event that City Forestry and TreePGH are both unable to provide and install the trees. Tree pit preparation by the General Contractor is included in the Base Bid under Item 51 regardless of whether this Alternate is awarded. This Alternate shall be awarded only upon written direction from the Owner.

Item No. 1a: Tree Furnishing and Installation (2½" CAL.) – Add Alternate 1 Unit of Measurement: Each Description:

1. Furnishing and complete installation of 2½-inch caliper trees — 33 EA total — as identified on the Planting Plan Drawings (sheets L120–L124)

1. Trees to be nursery-grown, balled-and-burlapped (B&B) stock meeting ANSI Z60.1 standards

1. All delivery, planting, staking, mulching, watering, and initial maintenance required for a complete installation

1. Tree pit preparation is included in the Base Bid under Item 51

1. This Alternate shall be awarded only upon written direction from the Owner

1. Species: Amelanchier canadensis / Canadian Serviceberry (7), Alnus serrulata / Hazel Alder (13), Cercis canadensis / Eastern Redbud (6), Cornus florida / Flowering Dogwood (3), Malus domestica 'Gala' / Gala Apple (2), Malus domestica 'Honeycrisp' / Honeycrisp Apple (2)

Item No. 1b: Tree Furnishing and Installation (3" CAL.) – Add Alternate 1 Unit of Measurement: Each Description:

1. Furnishing and complete installation of 3-inch caliper trees — 36 EA total — as identified on the Planting Plan Drawings (sheets L120–L124)

1. Trees to be nursery-grown, balled-and-burlapped (B&B) stock meeting ANSI Z60.1 standards

1. All delivery, planting, staking, mulching, watering, and initial maintenance required for a complete installation

1. Tree pit preparation is included in the Base Bid under Item 51

1. This Alternate shall be awarded only upon written direction from the Owner

1. Species: Betula alleghaniensis / Yellow Birch (5), Nyssa sylvatica / Black Gum (10), Platanus occidentalis / American Sycamore (2), Quercus alba / White Oak (19)

Alternates and Unit Prices Page 1 of 2