Amend_0007_10_28_13_Revised 4-18.pdf

SOF ASSESSMENT AND SELECTION TRAINING COMPLEX

CAMP MACKALL, NC

PN 86021 FY20

NORTH CAROLINA

SECTION 10 28 13 Page 1

(REVISED BY AMENDMENT)

PART 1 GENERAL

1.1 SUBMITTALS

SECTION 10 28 13*

TOILET ACCESSORIES

08/17

Government approval is required for submittals with a "G" designation;

submittals not having a "G" designation are for information only.

Submittals with an "S" are for inclusion in the Sustainability eNotebook, in conformance to Section 01 33 29.00 37 SUSTAINABILITY REPORTING. Submit the following in accordance with Section 01 33 00.00 37 SUBMITTAL

PROCEDURES:

SD-03 Product Data

Accessory Items; S

LEED data in support of the following credits: Environmental

Products Declarations and Sourcing of Raw Materials; S

SD-11 Closeout Submittals

Recycled content for stainless steel toilet accessories

Recycled Content

1.2 DELIVERY, STORAGE, AND HANDLING

Wrap toilet accessories for shipment and storage, then deliver to the jobsite in manufacturer's original packaging, and store in a clean, dry area protected from construction damage and vandalism.

PART 2 PRODUCTS

2.1 MANUFACTURED UNITS

Provide toilet accessories as indicated on the drawings. Provide each accessory item complete with the necessary mounting plates of sturdy construction with corrosion resistant surface.

Provide stainless steel products listed herein manufactured from materials containing a minimum of 50 percent recycled content. Provide data identifying percentage of recycled content for stainless steel toilet accessories.

2.1.1 Anchors and Fasteners

Provide anchors and fasteners capable of developing a restraining force commensurate with the strength of the accessory to be mounted and suited for use with the supporting construction. Provide tamperproof design exposed fasteners with finish to match the accessory.

PN 86021 FY20

NORTH CAROLINA

SECTION 10 28 13 Page 2

(REVISED BY AMENDMENT)

2.1.2 Finishes

Except where noted otherwise, provide the following finishes on metal:

Metal Finish

Stainless steel No. 4 satin finish

2.2 ACCESSORY ITEMS

Conform to the requirements for accessory items specified below.

2.2.1 Mirror, Metal (MM)

Provide a brightly polished stainless steel metal mirror of 0.037 inch minimum thickness, edges turned back 1/4 inch and recess fitted with tempered hardboard backing, and theft-proof fasteners. Provide size in accordance with paragraph SCHEDULE.

2.2.2 Toilet Tissue Dispenser (TTD)

Furnish Type II - surface mounted toilet tissue holder with two rolls of standard tissue. Provide stainless steel, satin finish cabinet.

2.2.3 Mop and Broom Holder (MH)

Stainless steel with grip jaw cam mechanism securing 3 mop or broom handles. Also includes hooks and storage shelf.

*2.2.4 Robe Hook (RH)

Provide heavy-duty robe hook. Flange and hook to be one-piece brass casting with nickel-plated finish to match stainless steel.

PART 3 EXECUTION

3.1 INSTALLATION

Do not install items that show visual evidence of biological growth.

Provide the same finish for the surfaces of fastening devices exposed after installation as the attached accessory. Provide oval exposed screw heads. Install accessories at the location and height indicated. Protect exposed surfaces of accessories with strippable plastic or by other means until the installation is accepted. After acceptance of accessories, remove and dispose of strippable plastic protection. Coordinate accessory manufacturer's mounting details with other trades as their work progresses. After installation, thoroughly clean exposed surfaces and restore damaged work to its original condition or replace with new work.

3.1.1 Surface Mounted Accessories

Mount on concealed backplates, unless specified otherwise. Conceal fasteners on accessories without backplates. Install accessories with sheet metal screws in PTFE or neoprene sleeves, or expansion shields, or with toggle bolts or other approved fasteners as required by the construction. Install backplates in the same manner, or provide with lugs

PN 86021 FY20

NORTH CAROLINA

SECTION 10 28 13 Page 3

(REVISED BY AMENDMENT)

or anchors set in mortar, as required by the construction. Fasten accessories mounted on gypsum board walls without solid backing into the metal or wood studs or to solid wood blocking secured between wood studs, or to metal backplates secured to metal studs.

3.2 CLEANING

Clean material in accordance with manufacturer's recommendations. Do not use alkaline or abrasive agents. Take precautions to avoid scratching or marring exposed surfaces.

-- End of Section --

PN 86021 FY20

NORTH CAROLINA

SECTION 10 28 13 Page 4

(REVISED BY AMENDMENT)

THIS PAGE INTENTIONALLY LEFT BLANK