101-UAC03C06v_01_0 PERFORM FIELD MAINTENANCE ON THE (LRSR).pdf
PDF 263 KB Posted
- Attached to
- Small Arms Maintenance (SAM 31)
- Solicitation number
- W912PB-27-Q-A004
About this file
This is a CRM Lesson Plan Report for training unit armorers on performing field maintenance on the M107 Long-Range Sniper Rifle (.50 caliber). The lesson plan was approved and became effective on 08 August 2025.
The lesson introduces newly designated unit armorers to field maintenance procedures for the M107 Sniper Rifle in accordance with technical manuals TM 9-1005-239-10, TM 9-1005-239-23&P, and DA Pam 750-8. The terminal learning objective requires students to perform field maintenance on the M107 by finding all deficiencies without losing accountability and without error. The lesson supports Army Learning Area professional competence and General Learning Outcome 14. Total instructional hours are 5 hours resident instruction for academics, plus 3 hours 20 minutes of instructor action time. The lesson comprises six learning steps: identifying characteristics, capabilities, and major components; clearing the rifle; disassembling and troubleshooting; reassembling; performing functional checks; and conducting preventive maintenance. Required equipment includes one M107 rifle (1:1 student ratio), industrial safety goggles (1:1 ratio), a repairman's small arms toolkit (1:10 ratio), two laptop computers, one tablet, one printer, and one interactive display monitor. Students receive .50 caliber dummy rounds at a 10:1 student ratio. The lesson is classified as Unclassified with FD3 foreign disclosure restrictions prohibiting use with international military students. Distribution is authorized only to U.S. Government agencies and their contractors. All instructor preparation requires thorough study of the lesson and referenced materials with emphasis on safety protocols, particularly regarding buffer spring tension and barrel spring tension hazards.
View the file
Other files
Show all 15
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
CUI
CRM LESSON PLAN REPORT
PERFORM FIELD MAINTENANCE ON THE LONG-RANGE SNIPER RIFLE (LRSR) .50 CAL, M107
101-UAC03C06 / 01.0 ©
Approved 08 Aug 2025
Effective Date: 08 Aug 2025
SCOPE:
This lesson introduces the newly designated unit armorer on how to perform Field Maintenance on the Long Range Sniper Rifle (LRSR) .50 cal, M107 with equipment. The expected learning outcomes is for the student to be able to perform Field Maintenance on the M107 Sniper Rifle in accordance with TM 9-1005-239-10, TM 9-1005-239-23&P and DA Pam 750-8, finding all deficiencies without losing accountability. This lesson supports the Army Learning Area (ALA) of professional competence, and General Learning Outcome (GLO) 14, Soldiers and Civilians are technically and tactically competent. The goal of this lesson is to provide the Student with the knowledge and skills to perform Field Maintenance on the M107 Sniper Rifle without supervision and to the standards outlined in TM 9-1005-239-10, TM 9-1005-239-23&P, DA Pam 750-8 and ARIMS User Guide.
Distribution Restriction: Distribution authorized to U.S. Government agencies and their contractors only The pbulication is required for administrative and operational purposes. This determination was made on 30 AUGUST 2005. Insert Rock Island, IL 61299 Destruction Notice: Destroy by any method that will prevent disclosure of contents or reconstruction of the document Foreign Disclosure: FD3 - This training product has been reviewed by the developers in coordination with the ARMORER TSP foreign disclosure officer. This training product cannot be used to instruct international military students.
SECTION I. ADMINISTRATIVE DATA
All Course Masters/POIs Including This Lesson
Courses
Course Number
None
POIs
Version Title Phase Status
Task(s) Taught(*) or Supported
Reinforced Task(s)
Knowledge
Skill
Administrative/ Academic Hours
Instructor Action
Test Lesson(s)
Prerequisite
POI Number Version Title Phase Status
Task Number Task Title Status
Task Number
Task Title
Status
Knowledge Id
K22092
Title
Understand general PMCS principles and procedures
Taught
Yes
Required
No
Skill Id
101-S-M014
Ability to perform PMCS on equipment used.
Taught
No
The administrative/academic (50 min) hours required to teach this lesson are as follows:
Academic Resident Hours / Methods
Yes
0 hrs 0 hrs 4 hrs
40 mins 10 mins
0 mins
Discussion (Small or Large Group) Reflective Discussion Demonstration
Total Hours(50 min): 5 hrs 0 mins
The instructor action (60 min) hours required to teach this lesson are as follows:
Hours/Actions
Lesson(s)
0 hrs 15 mins Classroom Breakdown
0 hrs 15 mins Classroom Setup 1 hrs 0 mins Logistics Support – Weapon 0 hrs 25 mins Student Counseling 1 hrs 0 mins Student Re-test 0 hrs 25 mins Student Re-train
Total Hours (60 min): 3 hrs 20 mins
Lesson Number Version
Lesson Title
Lesson Number Version
Lesson Title
Training Material Classification
Security Level: This course/lesson will present information that has a Security Classification of: U - Unclassified.
Foreign Disclosure Restrictions
References
Student Study Assignment
FD3. This training product has been reviewed by the developers in coordination with the ARMORER TSP foreign disclosure officer. This training product cannot be used to instruct international military students.
Number
Date ARIMS User Guide Army Records Information Management System
(ARIMS) User Guide 04 Aug 2022
DA PAM 750-8 The Army Maintenance Management System (TAMMS) Users Manual
22 Aug 2005
TM 9-1005-239-10 OPERATOR'S MANUAL LONG RANGE SNIPER
RIFLE (LRSR), CALIBER .50, M107
30 Nov 2010
TM 9-1005-239-23&P UNIT AND DIRECT SUPPORT MAINTENANCE
MANUAL (INCLUDING REPAIR PARTS
30 Sep 2010
Instructor Requirements
Support Personnel
Additional Support Personnel
Primary Instructor and Assistant Instructor(s)
Armorer Computer System Analyst
Student
Man
Equipment for Instruction
Name Ratio Qty Hours
Armorer 0:0 1 1.0 Remarks:
Computer System Analyst 0:0 1 8.0 Remarks:
ID - Name Student Instructor
Ratio Ratio Spt Qty Exp
1005-01-469-2133 - Rifle, Sniper: 1:1 0:0 No 1 No M107
Remarks:
4240-01-504-0052 - 1:1 1:1 No 0 No
GOGGLES,INDUSTRIAL
Remarks:
5180-00-357-7770 - Tool Kit, 1:10 0:0 No 1 No Repairman's, Small Arms
Remarks:
7021-01-C14-3190 - Computer, Micro 0:0 0:0 No 2 No Lap-Top Portable AC: M4500 Dell
Remarks: 1 on monitor table
7021-01-D01-0269 - PC Tablet, Data 1:1 0:0 No 1 No Entry: IPAD 2 WIFI 64GB Apple
Remarks:
7025-01-C11-4208 - Printer, Daisy 0:0 0:0 No 1 No Wheel/Dot Matrix/:2335DN MFP Dell
Remarks:
7050-01-C14-4309 - Interactive Pen 0:0 0:0 No 1 No Display: ID422W Smart
Remarks:
7490-01-T00-0291 - Card 1:1 0:0 No 0 No Programmer: RFC-03G Turning
Technologies
Remarks:
7490-01-T00-0292 - Card 1:30 0:0 No 0 No Programmer: XRC-R02 Turning
Technologies
(Note: Asterisk before ID indicates a TADSS.)
Materials
Instructor Materials:
a. Lesson Plan.
b. Practical Exercise (PE)
c. Practical Exercise Solution.
d. Required publications.
e. Safety Goggles.
Student Materials:
Classroom, Training Area, and Range
a. Student Handout.
b. Practical Exercise.
c. Required Publications.
d. Pen or pencil.
e. Safety Goggles.
ID - Name Quantity Student
Ratio
Setup Mins
Cleanup
Mins Requirements 17135-3000
Laboratory Instructional Building, 3000 Square Foot
1:30 20 30
Ammunition Requirements DODIC - Name Exp
Student Ratio
Instruct Ratio
Spt Qty
AB48 - Dummy .50 Caliber (Not Linked)
N 10:1 10:3
Instructional Guidance/ Conduct of Lesson
NOTE: Before presenting this lesson, instructors must thoroughly prepare by studying this lesson and identified reference material.
NOTE: Instructor/Facilitator will ensure to incorporate ALM and OE experiences.
Army Learning Model All instructors/facilitators will facilitate training using the Army Learning Model. Ensuring training is based on quality, relevance and effectiveness of face-to-face learning experiences through outcome-oriented instructional strategies. This type of instruction will foster critical thinking, initiative and operational relevance in context.
OE Integration Instructors/Facilitators will facilitate conversations from students and relate this lesson to current operational environments (OE) using personal experiences and/or examples obtained from the Center of Army Lessons Learned (CALL). Instructors/facilitators should provide sufficient OE variables and scenarios to produce the desired soldier training outcome for this lesson.
NOTE: Verify that training data is loaded and operational on the system before beginning the lesson.
Proponent Lesson Plan Approvals
Name Rank Position Date michelle.r.brown8.civ Not available Approver 08 Aug 2025
SECTION II. INTRODUCTION
Method of Instruction: Discussion (Small or Large Group) Mode of Delivery: Resident Instruction
Instr Type (I:S Ratio): Military - ICH (1:30) Time of Instruction: 10 mins
Motivator INSTRUCTOR NOTE: Have Soldiers draw weapons from the arms room.
SLIDE 92Y10D07-1 (ON)
The Commander has designated you as his unit armorer, responsible for the field maintenance of small arms. The unit armorer is an important job and requires attention to detail. You must have the skills and ability to perform all field maintenance tasks. As a unit armorer, you will also prepare, maintain, submit and file all maintenance documentation for the unit's weapons. If the M107 Long Range Sniper Rifle is not maintained to the highest standard, the weapon may not operate, could cause accident or injury, unit readiness will be degraded, and your unit may not be prepared to perform its mission.
Introduce the lesson to the students
SLIDE 92Y10D07-1 (OFF)
SLIDE 92Y10D07-2 (ON)
Review the Terminal Learning Objective with the students.
SLIDE 92Y10D07-2 (OFF)
Terminal Learning Objective
Safety
NOTE. Inform the students of the following Terminal Learning Objective requirements.
At the completion of this lesson, you [the student] will:
Action: Perform Field Maintenance on the Long-Range Sniper Rifle (LRSR) .50 Cal, M107
Conditions:
In a classroom environment, given the requirement to perform field maintenance on the
M107 Sniper Rifle. Given TM 9-1005-239-10, TM 9-1005-239-23&P, DA Pam 750-8, a DA
Form DA 2407, dummy rounds, armorer toolkit, safety equipment, and a M107 Sniper Rifle.
Standards:
Perform field maintenance on the M107 Sniper Rifle by finding all deficiencies without losing accountability, without error.
Learning Domain - Level: None assigned
No JPME Learning Areas Supported: Supports GLO 10 & 11.
General classroom, weapon and electrical equipment safety procedures will be followed.
Before starting an inspection and/or performing any maintenance procedures, be sure to clear the weapon. During the clearing procedure always keep the weapon pointed in a safe direction.
A potential safety hazard exists if the weapon is assembled or disassembled incorrectly.
Do not attempt to disassemble or assemble this weapon until the Instructor tells you to do so, nor should you attempt to adjust or remove the sight from this weapon unless specifically directed by the Instructor in the classroom.
Risk Assessment Level
Students will ensure that safety goggles are worn at all times during the disassembly and assembly of this weapon.
Medium - Back Plate/Buffer/Spring
Assessment:
During assembly/disassembly of the back plate; the buffer and buffer spring are under heavy tension, injury may result if spring is released suddenly
Controls:
Additional instructor(s) and increased supervision; ensure bolt is in the forward position; ensure proper placement of hand. Pull bolt carrier rearward and insert rear lock pin through the middle part of the buffer spring, gently releasing.
Leader Actions:
1. Primary Instructor will utilize "stop-go" method when training. Students will not proceed until told to do so. Instructor will spot check each weapon.
2. When possible, additional instructor(s) qualified with weapons will assist the primary instructor during the block of instruction.
3. Continually emphasize safety. Let students know what the outcome will be if procedures are not followed exactly as described.
Medium - Barrel/Barrel Springs Assessment:
During assembly/disassembly of the barrel; the barrel springs are under heavy tension of up to 70 pounds of pressure, injury may result if springs are released suddenly.
Controls:
Additional instruction and increased supervision: ensure proper placement of hand. Gently work the barrel key spring yolk from side to side until gently released. When reattaching firmly grasp barrel key when placing into forward slot.
Leader Actions:
1. Primary Instructor will utilize "stop-go" method when training. Students will not proceed until told to do so. Instructor will spot check each weapon.
2. When possible, additional instructor(s) qualified with weapons will assist the primary instructor during the block of instruction.
3. Continually emphasize safety. Let students know what the outcome will be if procedures are not followed exactly as
Low - Bolt/Extractor/Plunger spring Assessment: During assembly/disassembly of the bolt always point the bolt away from face and eyes to avoid injury if parts fly free.
Controls:
Additional instruction and increased supervision: safety goggle usage; ensure proper placement of hand; cover plunger spring with thumb while sliding extractor out of slot or into slot.
Leader Actions:
1. Primary Instructor will utilize "stop-go" method when training. Students will not proceed until told to do so. Instructor will spot check each weapon.
2. When possible, additional instructor(s) qualified with weapons will assist the primary instructor during the block of instruction.
3. Continually emphasize safety. Let students know what the outcome will be if procedures are not followed exactly as
Environmental Considerations
Instructional Lead-in
NOTE: Instructor should conduct a risk assessment to include environmental considerations IAW the current environmental considerations publication, and ensure students are briefed on hazards and control measures.
NOTE: It is the responsibility or all Soldiers, DA Civilians, and Contractors to protect the environment from damage.
NOTE: Have dirty rags turned in to the supply room and cleaned on a weekly basis.
Explain to the Student that performing field maintenance on small arms is similar to performing maintenance on a car. It is important to keep your car in good running condition so you can get back and forth to work. In the U.S. Army, weapons must be maintained to specified standards so the unit can successfully perform its mission.
SECTION III. PRESENTATION
TLO - LSA 1. Learning Step / Activity TLO - LSA 1. Identify the Characteristics, Capabilities and Features, and Major Components
Method of Instruction: Discussion (Small or Large Group)
Instr Type (I:S Ratio): Military - ICH (1:10)
Time of Instruction: 30 mins Media Type: Actual Equipment / PowerPoint Presentation Other Media: Unassigned
Security Classification: This course/lesson will present information that has a Security Classification of: U - Unclassified.
SLIDE 3 ON:
INSTRUCTOR NOTE: Refer students to TM 9-1005-239-23&P, WP 0002-1 or TM 9-1005-239-10, WP
0002-1.
1) Characteristics: The basic M107 Sniper Rifle is equipped with bipod, muzzle brake, carrying handle, and 10-round removable magazine. The M107 system is composed of the rifle and a sniper scope, plus spare magazines. The rifle is also supplied with fitted carrying case, the requisite cleaning kit, drag bag, cleaning equipment, and the telescope adjustment tools. The M107 is a semi-automatic, air-cooled, box magazine-fed rifle chambered for .50 caliber ammunition, This rifle operates by means of the short recoil principle, rather than gas.
2) Capabilities: The M107 is a long-range sniper weapon system which utilizes standard .50 caliber ammunition. The M107 is a man-portable, direct line-of-sight system capable of providing precision fire on targets at distances up to 2000 yards (1,830 meters).
b. Location and description of major components:
INSTRUCTOR NOTE: Inform students on the location and description of major components. Refer students to TM 9-1005-239-23&P, WP 0002-2.
1) Upper Receiver Assembly: Includes the front sight, accessory base, carrying handle, muzzle brake, and barrel.
2) Rail: Used to attach the scope, the carrying handle and accessory optic sights.
3) Carrying Handle: Steel stock with hard plastic handle.
4) Front Sight: A 0.075 in. (0.19 cm) post.
5) Muzzle Brake: Critical to the functioning of the weapon; absorbs approximately 70% of the recoil.
6) Barrel: Length is 29 in. with 8 lands and grooves, in a uniform right hand twist, one turn in 15
in. Muzzle end is threaded to accept a muzzle brake; breech end has a barrel extension integral to the locking function.
7) Bolt Assembly: Houses the firing pin, extractor, and ejector.
8) Bolt and Carrier Assembly: Consists of the bolt, firing pin, all extraction and ejection mechanisms, cocking lever, and sear.
9) Bipod Assembly: Detachable forward support system composed of retractable legs and extending foot pads.
10) Lower Receiver Assembly: Includes detachable bipod assembly, buffer assembly, midlock pin, and trigger mechanism.
Equipment Data
c. M107 LRSR Equipment Data. The M107 Sniper Rifle System comprises the rifle with a fixed variable
4.5 x 14 power sniper scope, and six magazines. Also supplied are a fitted dirt-tight and watertight carrying case, cleaning kit, and telescope adjustment tools.
INSTRUCTOR NOTE: Refer students to TM 9-1005-239-23&P, WP 0002-4. Click on the picture to hear some of the specifications of the weapon.
INSTRUCTOR NOTE: Refer students to TM 9-1005-239-10, WP 0019-3
d. Compatible ammunition includes:
1) MK211 Mod 0, Caliber .50 API (Armor Piercing Incendiary) Cartridge.
2) M33, Caliber .50 Ball Cartridge.
3) M17, Caliber .50 Tracer Cartridge.
4) M8, Caliber .50 API Cartridge.
5) M20, Caliber .50 APIT (Armor-Piercing Incendiary Tracer) Cartridge.
6) M1A1, Caliber .50 Blank Cartridge.
e. A toolkit and special tools included with the weapon system are the only tools applicable for performing the maintenance as indicated in the TM. Follow the instructions in the TM 9-1005-239-23&P for the correct tool to use for each procedure described. Use only the right tool for the job. Otherwise, you may cause damage to the weapon that will render it unsafe or unserviceable!
INSTRUCTOR NOTE: Refer students to TM 9-1005-239-23&P, WP 0003-1.
1) Feeding. The force of the mainspring pushes the bolt forward toward the barrel extension, stripping a cartridge from the magazine and loading it into the chamber (by hand when first loading, by semiautomatic action afterwards.)
2) Chambering. The bolt forces the round fully into the firing chamber, and the extractor snaps over the case rim. Blockages (dirt or debris) can prevent full chambering, as can dirty, bent, dented, or otherwise faulty ammunition.
3) Locking. During chambering the bolt enters the barrel extension, and the bolt latch engages the bolt latch trip (inside top of the upper receiver, just behind barrel extension). The bolt latch is then depressed, allowing the bolt to retract into the bolt carrier. The bolt, in turn, rotates due to the cam slot and is locked when its three locking lugs rotate into place in the barrel extension, closing the firing chamber.
4) Firing. Pulling the trigger pivots it on the trigger housing pin and presses on the transfer bar, causing the bar to rise. The transfer bar engages the sear (housed in the bolt carrier), forcing it upward and out of engagement with the firing pin extension. The firing pin extension, under spring power, forces the firing pin forward to strike the primer of the cartridge.
5) Unlocking. When the cartridge is fired, gas pressure exerts a thrust on the bolt face via the case head. The bolt carrier carries the bolt and barrel extension to the rear until the accelerator, protruding beneath the bolt carrier, contacts a shoulder in the trigger housing area. The accelerator is then pivoted up, causing the accelerator rod to be pushed out of the bolt carrier. As it protrudes from the front of the bolt carrier, it separates the bolt carrier from the barrel extension. because of the cam slot in the side of the bolt, the bolt rotates as it is pulled and unlocks from the barrel extension.
6) Cocking. As the bolt recoils to the rear, the cocking lever "rides" the transfer bar back and down, causing it to disconnect from te trigger. The transfer bar is held down in this position by the disconnector and is not released until pressure is released from the trigger. After disconnection, the cocking lever swings on its pin and overrides the transfer bar. The other end of the cocking lever protrudes into the bolt carrier and into the firing pin extension. As the cocking lever pivots, it withdraws the firing pin and compresses the firing pin extension spring. The firing pin extension then catches the sear.
7) Extraction. As the bolt locking lugs rotates away from the barrel extension, the bolt withdraws from the barrel and the bolt latch locks the bolt in its extended position. The extractor, located on the bolt face and hooked over the rim of the fired case, pulls the case from the firing chamber.
8) Ejection. As soon as the fired case has been extracted and has cleared the rear of the barrel extension, it is expelled from the rifle by the spring-powered ejector.
INSTRUCTOR NOTE: Refer students to TM 9-1005-239-23&P, pg. 0002-4 for M107 Rifle System.
SLIDE 3 OFF:
Check on Learning:
What is the Barrell Length?
29 inches
TM 9-1005-239-23&P PG 2-2
What assembly hoses the firing Pin?
Bolt Assembly
TM 9-1005-239-23&P PG 2-2
SLIDE 4(OFF)
Review Summary:
Conduct a Review/Summary of the information presented in the Learning Step Activity.
TLO - LSA 2. Learning Step / Activity TLO - LSA 2. Clear the M107 Sniper Rifle.
Method of Instruction: Demonstration
Instr Type (I:S Ratio): Military - ICH (1:10)*
Time of Instruction: 30 mins Media Type: Actual Equipment
Other Media: Unassigned Security Classification: This course/lesson will present information that has a Security
Note: Marked as (*) is derived from the parent learning object
SLIDE 4 ON:
INSTRUCTOR NOTE: Before starting an inspection, and/or performing any maintenance procedures, be sure to clear the weapon. Inform the students not to squeeze the trigger until the weapon has been cleared.
INSTRUCTOR NOTE: Refer students to TM 9-1005-239-10, WP 0005-13.
a. Unloading the M107 Sniper Rifle.
WARNING: The bolt does not automatically remain to the rear when the rifle or magazine is empty. After the rifle is unloaded, and with the charging handle to the rear, always physically check the chamber to ensure that the rifle is empty.
1) Put on your safety goggles.
2) Point weapon in a safe direction.
3) Place the weapon safety on “Safe”. Press the magazine catch forward towards the magazine and remove the magazine.
NOTE: Remember that the bolt does NOT automatically remain to the rear when the rifle or magazine is empty.
4) Pull the charging handle to the rear, which will eject any cartridge still chambered.
5) After the rifle is unloaded, and with the charging handle to the rear, look into the chamber to make certain the breech area and chamber are empty
b. Clearing
Caution: Whenever it is necessary to insert cleaning rods or other devices through the muzzle end of the barrel, be especially careful not to damage the muzzle's crown, since it could affect the accuracy of the rifle.
Caution: Do not leave rounds in the magazine for extended periods of time since this will cause the spring to lose tension and may cause a malfunction.
Determine if the students have learned the material presented by soliciting student questions and explanations. Ask the students questions and correct misunderstandings.
SLIDE 4 OFF:
Question: Where does the bolt of the M107 remain when the magazine is empty while firing?
Answer: The bolt will stay forward
TM 9-1005-239-10 PG 05-13
Review Summary:
Conduct a Review/Summary of the information presented in
TLO - LSA 3. Learning Step / Activity TLO - LSA 3. Disassemble and Troubleshoot the M107 Sniper Rifle.
Instr Type (I:S Ratio): Military - ICH (1:10)*
Time of Instruction: 1 hr 10 mins Media Type: Actual Equipment
Other Media: Unassigned Security Classification: This course/lesson will present information that has a Security
SLIDE 7 ON:
a. Disassembly of the M107 Sniper Rifle. I will now demonstrate how to disassemble the M107
Sniper Rifle. You will perform each task as I describe the sequence.
INSTRUCTOR NOTE: Refer students to TM 9-1005-239-10, WP 0013-1. NOTE: Unless there is something wrong with the telescope, it will not be removed for normal field stripping.
1) The following procedures will illustrate field stripping the M107 Sniper Rifle disassembly into the four major components: upper receiver assembly, lower receiver assembly, bolt and carrier assemblies and the telescopic sight assembly.
WARNING: Ensure that the weapon is unloaded and on SAFE before performing these procedures.
a) Remove rear lock and mid-lock pins.
b) Grasp charging handle on the bolt carrier assembly and pull to the rear (2-3 inches) until the bolt clears the barrel extension.
c) While holding the charging handle to the rear (2-3 inches), lift the back end of the upper receiver assembly until it clears the bolt. Allow the bolt carrier assembly to return to its forward position slowly.
d) Disengage front hook from the front hook pin on the lower receiver and lift upper receiver assembly clear of lower receiver assembly.
WARNING: Exercise extreme caution …… Buffer and buffer spring are under heavy spring tension. DO
NOT release springs suddenly. Failure to comply may result in personal injury. Ensure all students are wearing safety goggles and keep their faces away from the buffer assembly to avoid injury!
e) Pull the bolt carrier rearward and insert the rear lock pin through the buffer and buffer spring. CAUTION:
Remove the bolt carrier from the lower receiver and ensure carrier is completely forward of the housing before lifting bolt. Failure to comply may result in weapon damage.
f) Pull the bolt carrier assembly forward gently and lift out of the lower receiver assembly
INSTRUCTOR NOTE: The M107 Sniper Rifle is now separated into the four major components, the upper receiver assembly with the telescopic sight assembly attached, lower receiver assembly, the bolt, and carrier assemblies. Are there any questions on the disassembly (field stripping) of this weapon?
INSTRUCTOR NOTE: Refer students to TM 9-1005-239-23&P, WP 0016 00-1. Inform students that further disassembly is authorized at unit level although it may not be performed in the classroom.
2) Disassembly of the Lower Receiver and Trigger Assembly:
INSTRUCTOR NOTE: Restate the safety measures and protection required when removing the mainspring buffer. Failure to follow instructor directions could result in serious injury. Ensure each student has the bolt carrier removed by having students raise it in the air before proceeding to the next step.
WARNING: Mainspring buffer and mainspring are under heavy spring tension. Stand to one side to avoid flying parts. Wear eye protection and heavy work gloves. Failure to comply may result in injury.
WARNING: Wear eye protection during removal of mainspring or mainspring buffer in case of improper release. Failure to comply may result in personal injury.
a) Ensure that bolt carrier has been removed. Push (e.g., using a screwdriver) mainspring buffer manually to rear and place rear lock pin or a 1/8-inch punch through coils of mainspring and ports in lower receiver. This will relieve some of the pressure on the buffer as it is removed. WARNING: Ensure the rear lock pin is inserted to secure the mainspring buffer and mainspring. Failure to comply may result in personnel injury.
b) Place fingertip into slot on mainspring buffer and turn buffer so that groove in its flange lines up with buffer stop on lower receiver.
c) Remove the rear lock pin.
d) Remove mainspring buffer and mainspring slowly and carefully.
e) Remove lock knob from left rear handgrip. Remove monopod assembly carefully from lower receiver.
f) Use a T-25 T-handle Torx screwdriver to remove two rear hand grip screws, two rear hand grip nuts, right rear hand grip, and left rear hand grip.
INSTRUCTOR NOTE: Instructor will now direct the students to visually inspect (most common type of inspection) each part of the weapon that has been disassembled. Inspection should include observations of cracks stripped screws/nuts, excessive wear, and overall general cleanliness of the weapon. The Instructors will emphasis the importance of maintaining the weapon to fully mission capable condition and impacts on unit readiness. Reinforce use of Technical Manual/Maintenance Allocation Code to determine if repair and request of items is authorized at field level.
3) Disassembly of the Carrying Handle.
INSTRUCTOR NOTE: Refer students to TM 9-1005-239-23&P, WP 0020-1. a) Loosen carrying handle nut by turning counterclockwise. b) Slide carrying handle clamp away from body of carrying handle assembly and lift handle from rail.
INSTRUCTOR NOTE: Repeat the inspection process.
3) Lower barrel.
CAUTION: Do not pull on barrel springs to remove the barrel key assembly. doing so may damage the springs. Failure to comply may result in equipment damage.
a) Turn upper receiver upside down and remove barrel key.
b) Slide barrel back into receiver and rotate 1/2 turn.
c)Troubleshoot the M107 Sniper Rifle.
INSTRUCTOR NOTE: Refer students to TM 9-1005-239-23&P, WP 0004-1/2. Review the
Troubleshooting Introduction.
INSTRUCTOR NOTE: Refer students to TM 9-1005-239-23&P, WP 0005. Select one of the
Troubleshooting Malfunction/Symptom and walk students through determining the corrective actions listed in WP 0006.
SLIDE 7 OFF:
SLIDE 8 ON:
1. What is the first step of fieldstripping the M107?
answer: Remove rear lock and midlock. (TM 9-1005-239-10, pg. 0013-
5)
2. How many major components are there for fieldstripping the M107?
answer: four. (TM 9-1005-239-10, pg. 0013-3)
SLIDE 8 OFF:
Conduct a Review/Summary of the information presented in
TLO - LSA 4. Learning Step / Activity TLO - LSA 4. Assemble the M107 Sniper Rifle.
Instr Type (I:S Ratio): Military - ICH (1:10)*
Time of Instruction: 30 mins Media Type: Actual Equipment
Other Media: Unassigned Security Classification: This course/lesson will present information that has a Security
SLIDE 9 ON:
a. Reassemble the M107 Sniper Rifle and components.
1) Extend the barrel.
INSTRUCTOR NOTE: Refer students to TM 9-1005-239-23&P, WP 0013-5.
a) Pick up upper receiver assembly carefully. Barrel will be nested inside it for compact storage. Move bumper rings into position on either side of receiver's central barrel bushing so that they rest snugly against bushing. Align barrel so that its feed ramp (slanted entry to firing chamber) is to bottom. Keep fingers away from barrel, hold upper receiver horizontally, and then tilt in direction of muzzle. Barrel should fall into place, at its full forward extension in receiver.
WARNING: The tension on the barrel springs is about 70 lb (31.8 kg), which may cause the springs to release suddenly. Failure to comply may result in personnel injury.
WARNING: Avoid incomplete or improper assembly. Failure to comply may result in personnel injury.
b) Barrel springs in upper receiver are held in place by a spring yoke, the barrel key.
c) Maintain the downward tilt of upper receiver (to keep barrel in place), firmly grasp barrel key, not springs, and pull it into place on forward slot of barrel.
d) Work key from side to side until it is firmly seated in barrel slot.
3) Reassemble the Carrying Handle Assembly.
INSTRUCTOR NOTE: Refer student to TM 9-1005-239-23&P, WP 0021-4.
a) With carrying handle nut loosened, position carrying handle assembly on rail.
Align carrying handle clamp with handle mount of carrying handle assembly.
b) Tighten the carrying handle nut until the assembly is firmly secured on the mounting rail.
4) Reassemble the Lower Receiver Assembly.
INSTRUCTOR NOTE: Refer student to TM 9-1005-239-23&P, WP 0016-12.
a) Align right rear hand grip and left rear hand grip on lower receiver.
b) Using T-25 T—handle Torx screwdriver to install two rear hand grip screws and two rear hand grip nuts.
c) Slide Monopod assembly into lower receiver and secure with lock knob.
d) Slide mainspring into lower receiver.
WARNING: Mainspring buffer and mainspring are under heavy spring tension.
Stand to one side to avoid flying parts. Wear eye protection and heavy work gloves.
failure to comply may result in injury.
e) Place mainspring buffer on end of mainspring. Guide mainspring into housing until buffer is even with housing.
f) Place the end of a screwdriver into slot on mainspring buffer, and turn buffer so that groove in its flange lines up with buffer stop on lower receiver.
g) Push mainspring buffer to rear after mainspring has passed buffer stop WARNING: Ensure the rear lock pin is inserted to secure the mainspring buffer and mainspring. Failure to comply may result in personnel injury.
h) Turn screwdriver so that groove in mainspring buffer and buffer stop are no longer in line. Insert rear lock pin through mainspring for safety.
i) Ease off pressure applied to screwdriver until mainspring buffer stops on buffer stop.
5) Reassemble the M107 Semi-Automatic Sniper system.
INSTRUCTOR NOTE: Refer student to TM 9-1005-239-23&P, WP 0015-4.
a) Place bolt and carrier assembly into forward part of lower receiver assembly.
WARNING: Mainspring buffer and mainspring are under heavy spring tension.
Stand to one side to avoid flying parts. wear eye protection and heavy work gloves.
failure to comply may result in injury.
b) Pull bolt and carrier assembly rearward and carefully remove rear lock pin from mainspring and mainspring buffer.
c) Align front hook of upper receiver assembly with front hook pin on lower receiver assembly.
d) With upper receiver assembly in position on lower receiver assembly, secure with rear lock pin and midblock pin.
SLIDE 9 OFF:
SLIDE 10 ON:
1. What Tool is used to help assembly the M107?
Screwdriver (TM 9-1005-239-23&P, PG. 0025-1)
SLIDE 10 OFF:
Conduct a Review/Summary of the information presented in the Learning Step.
TLO - LSA 5. Learning Step / Activity TLO - LSA 5. Perform a Functional Check on the M107 Sniper Rifle.
Instr Type (I:S Ratio): Military - ICH (1:10)*
Time of Instruction: 30 mins Media Type: Actual Equipment
Other Media: Unassigned Security Classification: This course/lesson will present information that has a Security
SLIDE 11 ON:
INSTRUCTOR NOTE: Refer students to TM 9-1005-239-23&P, WP 0034.
Whenever the weapon is disassembled beyond normal fieldstripping, perform a functional check when the weapon is reassembled. This quick check indicates whether or not the weapon has been properly assembled with all of its components. A functional check can also reveal the more obvious malfunctions that occur between interactive components of the weapon.
To complete a functional check, perform the following procedure:
1) Load ten .50 caliber dummy rounds in magazine.
2) Insert the magazine into the weapon.
3) Retract bolt fully to rear and release to chamber the first round.
4) With the safety selector switch set to SAFE, attempt to fire the weapon. The weapon should not fire.
5) With the safety selector switch set to FIRE, attempt to fire the weapon. The weapon should fire.
6) While holding the trigger to the rear, pull the bolt all the way to the rear and release the bolt.
7) Release the trigger. A click should be heard and the weapon should fire.
8) Repeat steps 6 and 7 at least three times to ensure proper functioning.
9) Cycle the bolt through the remaining rounds to ensure proper feeding, chambering, extracting, and ejecting.
SLIDE 10 OFF:
Check on Learning: SLIDE 12 ON:
What is the 9th and final step of the M107 functions check?
Answer: Cycle the bolt through the remaining rounds to ensure proper feeding, chambering, extracting, and ejecting. (TM 9-1005-239-23&P, pg. 0034-1/2.
SLIDE 12 OFF:
Review Summary:
Conduct a Review/Summary of the information presented in
TLO - LSA 6. Learning Step / Activity TLO - LSA 6. Perform Preventive Maintenance on the M107 LRSR.
Instr Type (I:S Ratio): Military - ICH (1:10)*
Time of Instruction: 1 hr Media Type: Actual Equipment / PowerPoint Presentation Other Media: Unassigned
Security Classification: This course/lesson will present information that has a Security
Check on Learning: SLIDE 14 ON:
What TM covers "clean exterior of weapon to remove dirt and debris?
answer: (TM 9-1005-239-10)
SLIDE 14 OFF:
Conduct a Review/Summary of the information presented in
SECTION IV. SUMMARY
Method of Instruction: Reflective Discussion
Instr Type(I:S Ratio): Military - ICH (1:30) Time of Instruction: 10 mins
Check on Learning
Review/ Summary
Determine if the students have learned the material presented by soliciting student questions and explanations. Ask the students questions and correct misunderstandings.
Question: What WP Sequence number lists of items used to perform PMCS on the M107?
Answer: Sequence number 00060 00.
Question: What are the M107 Sniper Rifle’s major external components?
Answer: Upper Receiver Assembly, Rail, Carrying Handle, Front Sight, Muzzle Brake, Barrel, Bolt Assembly, Bolt and Carrier Assembly, Bipod Assembly, and the Lower Receiver Assembly.
Question: What section in TM 9-1005-239-23&P covers field troubleshooting instructions?
Answer: Section 0005.
Question: What position should the safety lever be in prior to performing a function check?
Answer: In the ”SAFE” position“
During this lesson we discussed the following topics:
a. Identify the Characteristics, Capabilities and Features, and Major Components of the M107 Sniper Rifle.
b. Clear the M107 Sniper Rifle.
c. Disassemble and Troubleshoot the M107 Sniper Rifle.
d. Reassemble the M107 Sniper Rifle.
e. Performa functional Check on the M107 Sniper Rifle
f. Perform Preventive Maintenance on the M107 Sniper Rifle
SECTION V. STUDENT EVALUATION
Testing
Feedback
NOTE: Describe how the student must demonstrate the accomplishment of the TLO. Refer student to the Student Evaluation Plan.
The student will be evaluated on disassembly/assembly procedures and conducting field maintenance on a GO/NO-GO basis. Student must receive a GO to be successful.
NOTE: Feedback is essential to improving training, always encourage students to provide comments and ensure to complete the Module AAR.
NOTE: Review the completed practical exercise with the students. Ensure lesson is understood by asking questions and receiving feedback from the students. Clear up any misunderstandings.
A-1
Appendix A - Viewgraph Masters
Perform Field Maintenance on the Long-Range Sniper Rifle (LRSR) .50 Cal, M107
101-UAC03C06 / Version 01.0 ©
Sequence Media Name Media Type
B-1
Appendix B - Assessment Statement and Assessment Plan
Assessment Statement: None.
Assessment Plan: None.
C-1
Appendix C - Practical Exercises and Solutions
PRACTICAL EXERCISE(S)/SOLUTION(S) FOR LESSON 101-UAC03C06 Version 01.0 ©
D-1
Appendix D - Student Handouts
Perform Field Maintenance on the Long-Range Sniper Rifle (LRSR) .50 Cal, M107
101-UAC03C06 / Version 01.0 ©
Sequence Media Name Media Type
1 M107 PE DOCX
| CRM LESSON PLAN REPORT |
| SECTION I. ADMINISTRATIVE DATA |
| SECTION II. INTRODUCTION |
| SLIDE 92Y10D07-1 (ON) |
| SLIDE 92Y10D07-1 (OFF) SLIDE 92Y10D07-2 (ON) |
| SLIDE 92Y10D07-2 (OFF) |
| SECTION III. PRESENTATION |
| SLIDE 3 ON: |
| SLIDE 3 OFF: |
| TM 9-1005-239-23&P PG 2-2 |
| TM 9-1005-239-23&P PG 2-2 |
| SLIDE 4 ON: |
| SLIDE 4 OFF: |
| SLIDE 7 ON: |
| SLIDE 7 OFF: |
| SLIDE 8 ON: |
| SLIDE 8 OFF: |
| SLIDE 9 ON: |
| SLIDE 9 OFF: |
| SLIDE 10 ON: |
| SLIDE 10 OFF: |
| SLIDE 11 ON: |
| SLIDE 10 OFF: |
| SLIDE 14 OFF: |
| SECTION IV. SUMMARY |
| SECTION V. STUDENT EVALUATION |
File details come from the government source that posted it. Updated .