101-UAC03C12v_01_0 PERFORM FIELD MAINTENANCE ON THE MACHINE GUN 7.62MM M240L.pdf
PDF 272 KB Posted
- Attached to
- Small Arms Maintenance (SAM 31)
- Solicitation number
- W912PB-27-Q-A004
About this file
This document is a Curriculum Resource Material (CRM) Lesson Plan Report for military training on field maintenance of the M240L Machine Gun, 7.62mm. The lesson is designated 101-UAC03C12/01.0, approved and effective as of August 8, 2025, with distribution restricted to U.S. Government agencies and their contractors only (FD3 foreign disclosure restriction preventing use with international military students).
The lesson introduces unit armorers to field maintenance procedures for small arms, specifically the M240B Machine Gun, with expected learning outcomes enabling students to perform field maintenance independently and to standards outlined in TM 9-1005-313-23&P, DA PAM 750-8, and TM 9-1005-313-10. The training requires 9 hours and 0 minutes of resident instruction (administrative/academic hours at 50-minute intervals) plus 3 hours and 20 minutes of instructor action time. Instruction methods include discussion, demonstration, reflective discussion, and practical hands-on exercises with an instructor-to-student ratio of 1:30 for most activities. The lesson encompasses seven learning steps: identifying characteristics and major components; clearing the weapon; disassembly procedures; troubleshooting; assembly; performing safety/function checks; and conducting preventive maintenance checks and services (PMCS) with documentation on DA Form 5988-E and DA Form 5990-E. Required equipment includes the M240B Machine Gun, armorer tool kit, safety goggles, computers, and dummy cartridges (A159 at 5:1 student ratio). A laboratory instructional building of 3,000 square feet accommodates up to 30 students with 20 minutes setup and 30 minutes cleanup. Students are evaluated on a GO/NO-GO basis for disassembly/assembly procedures and field maintenance tasks, and instructors must thoroughly prepare by studying lesson materials and reference publications before presentation.
View the file
Other files
Show all 14
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
CUI
CRM LESSON PLAN REPORT
PERFORM FIELD MAINTENANCE ON THE MACHINE GUN 7.62MM M240L.
101-UAC03C12 / 01.0 ©
Approved 08 Aug 2025
Effective Date: 08 Aug 2025
SCOPE:
This lesson introduces the newly designated unit armorer how to perform field maintenance of small arms. The expected learning outcomes is for the student to be able to perform field maintenance on the M240B Machine Gun, finding all deficiencies without losing accountability, in accordance with TM 9-1005-313-10, TM 9-1005-313-23&P, and DA Pamphlet 750-8. This lesson supports the Army Learning Area (ALA) of professional competence, and General Learning Outcome (GLO) 14, Soldiers and Civilians are technically and tactically competent. The goal of this lesson is to provide the Student with the knowledge and skills to perform the field maintenance of small arms without supervision and to the standards outlined in TM 9-1005-313-23&P, DA PAM 750-8 and TM 9-1005-313-10.
Distribution Restriction: Distribution authorized to U.S. Government agencies and their contractors only for specific authority and export control. This determination was made on 31 March 2006. Insert SFAE-SDR_CSW Building 151, Basement, Picatinny, NJ 07806 Destruction Notice: Destroy by any method that will prevent disclosure of contents or reconstruction of the document Foreign Disclosure: FD3 - This training product has been reviewed by the developers in coordination with the Unit Armor foreign disclosure officer. This training product cannot be used to instruct international military students.
SECTION I. ADMINISTRATIVE DATA
All Course Masters/POIs Including This Lesson
Courses
Course Number
None
POIs
Version Title Phase Status
Task(s) Taught(*) or Supported
Reinforced Task(s)
Knowledge
Skill
Administrative/ Academic Hours
Instructor Action
Test Lesson(s)
Prerequisite
POI Number Version Title Phase Status
Task Number Task Title Status
Task Number
Task Title
Status
Knowledge Id
K22092
Title
Understand general PMCS principles and procedures
Taught
Yes
Required
No
Skill Id
101-S-M014
Ability to perform PMCS on equipment used.
Taught
No
The administrative/academic (50 min) hours required to teach this lesson are as follows:
Academic Resident Hours / Methods
Yes Yes
0 hrs 0 hrs 6 hrs 1 hr
45 mins 15 mins 40 mins
0 mins
Discussion (Small or Large Group) Reflective Discussion Demonstration Practical Exercise (Hands-On/Written)
Total Hours(50 min): 9 hrs 0 mins
The instructor action (60 min) hours required to teach this lesson are as follows:
Hours/Actions
Lesson(s)
0 hrs 15 mins Classroom Breakdown
0 hrs 15 mins Classroom Setup 1 hrs 0 mins Logistics Support – Weapon 0 hrs 25 mins Student Counseling 1 hrs 0 mins Student Re-test 0 hrs 25 mins Student Re-train
Total Hours (60 min): 3 hrs 20 mins
Lesson Number Version
Lesson Title
Lesson Number Version
Lesson Title
Training Material Classification
Security Level: This course/lesson will present information that has a Security Classification of: U - Unclassified.
Foreign Disclosure Restrictions
References
FD3. This training product has been reviewed by the developers in coordination with the Unit Armor foreign disclosure officer. This training product cannot be used to instruct international military students.
Student Study Assignment None
Requirements
Support Personnel
Primary Instructor and Assistant Instructor(s)
Armorer Computer System Analyst
Additional Support Personnel
Student
Man
Number
Date
ARIMS User Guide Army Records Information Management System (ARIMS) User Guide
04 Aug 2022
DA PAM 750-8 The Army Maintenance Management System (TAMMS) Users Manual
22 Aug 2005
TM 9-1005-313-10 Operator Manual for Machine Gun, 7.62mm, M240, M240B, M240C, M240D, M240H, M240L
15 May 2022
TM 9-1005-313-23&P UNIT AND DIRECT SUPPORT MAINTENANCE
MANUAL (INCLUDING DEPOT MAINTENANCE
REPAIR PARTS) FOR MACHINE GUN, 7.62MM,
M240
20 Aug 2020
Name Ratio Qty Hours
Armorer Remarks:
0:0 1 1.0
Computer System Analyst Remarks:
0:0 1 8.0
Equipment for Instruction
ID - Name Student
Materials
Classroom, and Range Training Area, Ratio Ratio Spt Qty Exp
1005-01-412-3129 - Machine Gun,
7.62 Millimeter: M240B
Remarks:
1:1 0:0 No 1 No
1005-01-503-0141 - Mount, Machine Gun: M192 Remarks:
1:6 0:0 No 1 No
4240-01-504-0052 -
GOGGLES,INDUSTRIAL
Remarks:
1:1 1:1 No 0 No
5180-00-357-7770 - Tool Kit, Repairman's, Small Arms Remarks:
1:10 0:0 No 1 No
7021-01-C14-3190 - Computer, Micro Lap-Top Portable AC: M4500 Dell Remarks:
0:0 0:0 Yes 2 No
7021-01-D01-0269 - PC Tablet, Data Entry: IPAD 2 WIFI 64GB Apple Remarks:
1:1 0:0 No 1 No
7025-01-C11-4208 - Printer, Daisy Wheel/Dot Matrix/:2335DN MFP Dell Remarks:
0:0 0:0 No 1 No
7050-01-C14-4309 - Interactive Pen Display: ID422W Smart Remarks:
0:0 0:0 No 1 No
7490-01-T00-0291 - Card Programmer: RFC-03G Turning Technologies Remarks:
1:1 0:0 No 0 No
7490-01-T00-0292 - Card Programmer: XRC-R02 Turning Technologies Remarks:
1:30 0:0 No 0 No
(Note: Asterisk before ID indicates a TADSS.)
Instructor Materials:
a. Lesson Plan
b. Practical Exercise (PE)
c. Practical Exercise Solution
d. Required Publications
e. Safety Goggles
Student Materials:
a. Student Handout (Blank Forms)
b. Practical Exercise
c. Required Publications
d. Pen or pencil
e. Safety Goggles
ID - Name
Quantity
Ratio
Setup Mins
Cleanup
Mins
17135-3000 Laboratory Instructional Building, 3000 Square Foot
1:30 20 30
Ammunition Requirements DODIC - Name Exp
Instruct
Spt Qty
A159 - Dummy Cartridge, 7.62 Millimeter, M172 (Linked)
N 5:1 0:0
Instructional Guidance/ Conduct of Lesson
Proponent Lesson Plan Approvals
NOTE: Before presenting this lesson, instructors must thoroughly prepare by studying this lesson and identified reference material.
NOTE: Instructor/Facilitator will ensure to incorporate ALM2015 and OE experiences.
ARMY LEARNING MODEL
All Instructors/Facilitators will facilitate training under Army Learning Model. Ensuring training is based on quality, relevance and effectiveness of face to face learning experiences through outcome-oriented instructional strategies. This type of instruction will foster critical thinking, initiative and operational relevance in context.
OE INTEGRATION
Instructors/Facilitators will facilitate conversations from students and relate this lesson to current Operational Environments (OE) using personal experiences and/or examples obtained from the Center for Army Lessons Learned (CALL). Instructors should provide sufficient OE variables and scenarios to produce the desired soldier training outcome for this lesson.
NOTE: Verify that the training material is loaded on the computers before beginning the lesson.
Name Rank Position Date michelle.r.brown8.civ Not available Approver 08 Aug 2025
SECTION II. INTRODUCTION
Method of Instruction: Discussion (Small or Large Group) Mode of Delivery: Resident Instruction
Instr Type (I:S Ratio): Military - ICH (1:30) Time of Instruction: 15 mins
Motivator INSTRUCTOR NOTE: Have the students draw the M240B from the arms room.
SLIDE 92Y10D11-1 (ON)
The Commander has designated you as his or her unit armorer, responsible for the field maintenance of small arms. As a unit armorer, you will prepare, maintain, submit, and file all maintenance requirements for the unit's organizational weapons. You must have the skill set and the ability to perform all field maintenance tasks. The unit armorer is an important job and requires attention to detail. If the M240B Machine Gun is not maintained to proper standards, the weapon may not operate, unit readiness will be degraded, and your unit may not be prepared to perform its mission.
Introduce the lesson to the students.
SLIDE 92Y10D11-1 (OFF)
SLIDE 92Y10D11-2 (ON)
INSTRUCTOR NOTE: Discuss the Terminal Learning Objective with the students.
Terminal Learning Objective
Safety
SLIDE 92Y10D11-2 (OFF)
NOTE. Inform the students of the following Terminal Learning Objective requirements.
At the completion of this lesson, you [the student] will:
Action: Perform Field Maintenance on the Machine Gun 7.62mm M240L.
Conditions:
In a classroom environment, given the requirement to perform field maintenance on the M240B Machine Gun. Given TM 9-1005-313-10, TM 9-1005-313-23&P, DA Pamphlet 750-8, a DA Form 5988-E, DA Form 5990-E, armorer tool kit, safety equipment, M240B Machine Gun, and linked dummy rounds.
Standards:
Perform field maintenance on the M240L Machine Gun by finding all deficiencies without losing accountability, without error.
Learning Domain - Level: Psychomotor - Precision
No JPME Learning Areas Supported: Supports GLO 10 & 11.
General classroom, weapon, and electrical safety procedures will be followed.
Before starting an inspection and/or performing any maintenance procedures, be sure to clear the weapon. During the clearing procedure always keep the weapon pointed in a safe direction.
A potential safety hazard exists if the weapon is assembled or disassembled incorrectly.
Students will ensure that safety glasses are worn at all times during the assembly and disassembly of the weapon.
Risk Assessment Level
Low - Rod Assembly Driving Spring Assessment: During disassembly/assembly if not removed properly, the rod assembly driving spring can expel suddenly causing injury.
Controls: Additional instruction and supervision: Primary/Assistant instructor should ensure all bolts are in the forward position.
Additional instruction and supervision: Apply resistance to the rod assembly drive spring while removing and installing.
Wear safety glasses.
Leader Actions: Primary Instructor will utilize "stop-go" method when training. Students will not proceed until told to do
so. Instructor will spot check each weapon.
When possible, additional instructor(s) qualified on weapons will assist primary instructor during the block of instruction.
Continually emphasize safety. Let students know what the outcome will be if procedures are not followed exactly as described.
Environmental Considerations NOTE: Instructor should conduct a risk assessment to include environmental considerations
IAW the current environmental considerations publication, and ensure students are briefed on hazards and control measures.
NOTE: It is the responsibility of all Soldiers, DA Civilians, and Contractors to protect the environment from damage.
NOTE: Have dirty rags turned in to the supply room and cleaned on a weekly basis.
Instructional Lead-in Explain to the student that performing field maintenance on small arms is similar to performing maintenance on a car. It is important to keep your car in good running condition so you can get back and forth to work. In the U.S. Army, weapons must be maintained to specified standards so the unit can successfully perform its mission.
SECTION III. PRESENTATION
TLO - LSA 1. Learning Step / Activity TLO - LSA 1. Identify the Characteristics, Capabilities and Features, and Major Components of the M240L.
Method of Instruction: Discussion (Small or Large Group)
Instr Type (I:S Ratio): Military - ICH (1:10)*
Time of Instruction: 30 mins Media Type: Actual Equipment
Other Media: Unassigned Security Classification: This course/lesson will present information that has a Security
Classification of: U - Unclassified.
Note: Marked as (*) is derived from the parent learning object
SLIDE 3 ON: Click on picture to listen to the characteristics of the M240L.
INSTRUCTOR NOTE: Refer students to TM 9-1005-313-10, WP 0002-3.
a. Equipment Characteristics: The M240L is designed as a tripod mounted, vehicle mounted, or bipod supported machine gun for use by ground forces. The bipod is integrated into the receiver assembly of the weapon and has a forward rail accessory mounting. (Figure 5)
b. Capabilities and Features:
1) The M240 Series Machine Gun is gas-operated and fires from the open bolt position. The 7.62mm is the authorized round for the machine gun.
2) The M240B/M240L has an adjustable buttstock and hydraulic buffer assembly, an adjustable height bipod. The bipod is integrated into the receiver assembly of the weapon and has a forward rail for accessory mounting. Weapon can be mounted on the M122A1Tripod or M192 Lightweight Tripod.
INSTRUCTOR NOTE: Refer students to TM 9-1005-313-10, Table 1. M240 Major Components, WP 0002-4
c. Location and Description of Major Components.
1) Barrel Assembly-Houses cartridge for firing and directs projectile.
2) Buttstock and Buffer Assembly-Absorbs recoil for bolt and operating rod assembly at the end of recoil movement.
3) Driving Spring Rod Assembly-Provides energy for returning bolt and operating rod assembly to firing position.
4) Bolt and Operating Rod Assembly-Provides feeding, striping, chambering, firing, extraction, and ejection of cartridges using the projectile propelling gases for power.
5) Trigger Housing Assembly-Controls the firing of the machine gun.
6) Cover Assembly-Feeds linked belt, positions and holds cartridges in position for stripping, feeding and chambering. The cover has integral sight mounting rail for current/future accessories (all models except
M240C).
7) Feed Tray-Serves as a guide for positioning cartridges to assist in chambering.
8) Receiver Assembly-Serves as a support of all major components. The receiver houses action of weapon, and controls functioning of weapons through a series of cam ways. The receiver has a forward integral mounting rail for current/future accessories (M240L/M240B/M240H). (WP 0002-3 & WP 0002-4)
SLIDE 3 OFF:
Check on Learning:
SLIDE 4 ON:
Q: What is the 1st Description Major Component of the M240L?
A: Barrel Assembly: It houses cartridge for firing and directs projectile
(Figure 5, Item 1).
REF: TM9-1005-313-10. WP 0002-3 & WP
0002-4
Q: What is the 4th Description Major Component of the M240L?
A: Bolt and Operating Rod Assembly: It Provides feeding, striping, chambering, firing, extraction, and ejection of cartridges using the projectile propelling gases for power. (Figure 5, Item 4).
REF: TM 9-1005-313-10. WP 0002-3 & WP 0002-4
SLIDE 4 OFF:
Review Summary:
Conduct a Review/Summary of the information presented in the Learning Step.
TLO - LSA 2. Learning Step / Activity TLO - LSA 2. Clear the M240L Machine Gun.
Method of Instruction: Demonstration
Instr Type (I:S Ratio): Military - ICH (1:10)*
Time of Instruction: 1 hr Media Type: Actual Equipment
Other Media: Unassigned Security Classification: This course/lesson will present information that has a Security
SLIDE 5 ON:
INSTRUCTOR NOTE: Refer students to TM 9-1005-313-10, WP 0005-1.
a. Clear the M240L Machine Gun.
WARNING: Under no circumstances should the safety be engaged with the bolt in the forward position. Always ensure the safety is in the fire position before charging the weapon; otherwise, the weapon will become jammed when charged with the safety in the safe position. Failure to comply with above warnings may result in injury or death to personnel.
1) Place safety to "F" fire before actuating the bolt/operating rod assembly.
2) Pull charge cable handle (or cocking handle) fully to rear, and ensure bolt locks completely to rear.
3) Return cocking handle assembly (or charge cable) to fully forward and locked position.
4) Place safety to "S" safe.
5) Push in latches to open cover assembly.
6) Remove ammunition belt.
7) Raise feed tray.
8) Look into chamber to make sure it is empty. If a round is still in the chamber, refer to ruptured/stuck cartridge case or live round procedures.
9) Lower feed tray.
10) Place safety to "F" fire.
11) Pull and hold cocking handle assembly (or charging cable) to rear while fully depressing the trigger while easing the bolt forward to close and lock. Release the trigger. Safety must not be able to be moved to the safe position.
12) Close cover assembly. Make sure it locks shut.
NOTE: Be sure bolt is forward with safety in "F" fire when gun is not in use.
SLIDE 5 OFF:
Check on Learning: SLIDE 5 ON:
Q: What is the 1st step when clearing the M240L?
A: Place safety to "F" fire before actuating the bolt/operating rod assembly
(Figure 1)
REF: TM 9-1005-313-10, WP 0005-1
Q: What is the 11th step when clearing the M240L?
A: Pull and hold charge cable (Figure 1) or cocking handle assembly
(Figure 1) to rear. Fully depress and hold trigger, the easing charger cable or cocking handle assembly fully forward to close and lock bolt.
REF: TM 9-1005-313-10, WP 0005-3
SLIDE 5 OFF:
TLO - LSA 3. Learning Step / Activity TLO - LSA 3. Disassemble the M240B Machine Gun.
Instr Type (I:S Ratio): Military - ICH (1:10)*
Time of Instruction: 1 hr Media Type: Actual Equipment
Other Media: Unassigned Security Classification: This course/lesson will present information that has a Security
SLIDE 7 ON:
INSTRUCTOR NOTE: Refer students to TM 9-1005-313-10, WP 0021-1.
a. Disassemble the M240L Machine Gun.
1) Clear your machine gun.
2) Depress barrel locking latch and hold.
3) Turn barrel release/carrying handle to upright position.
4) Remove barrel. Push forward and lift out barrel.
5) To M240L/M240 only: Remove heat shield assembly from barrel. Lift rear of heat shield assembly off barrel then pry front tabs out of holes on gas hole bushing.
6) Depress spring and remove spring pin. (This can usually be done without tools).
7) Pull trigger housing down and back.
8) Depress back plate latch and lift buffer/buttstock and buffer assembly/buffer and spade grip assembly straight up.
9) Depress driving spring in, up, and out.
10) Depress cover latches
11) Raise cover assembly to first latching position
12) Pull cocking handle assembly
13) Push out spring pin as far as possible. Remove pin with fingers.
14) Lift cover assembly upward and remove the feed tray.
15) Extend bipod legs and locked position to collapse the bipod legs.
WARNING: Protect hands/fingers when raising cover. Injury could result
a. Depress cover latches and raise cover assembly to first latching position. Pull cocking handle assembly back; then pull bolt and operating rod assembly out.
CAUTION: Do not hit the cover pin with the back of the buffer or the pin will be damaged.
b. Push out spring pin as far as possible with the back of buffer. Then remove pin with fingers. Lift upward and remove cover assembly. Remove feed tray
c. In order to collapse the bipod legs is recommended to be in a flat surface this will allow you more precision and stability.
SLIDE 7 OFF:
Check on Learning:
SLIDE 8 ON:
Q: What is the 5th step when disassembling the M240L?
A: Remove heat shield assembly (Figure 2) from barrel.
Lift rear of heat shield assembly off barrel then pry front tabs out of the holes on the gas bushing.
REF: TM 9-1005-313-10, WP 0021-1
Q: What is the 18th step when disassembling the M240L?
A: Extend bipod legs to down and locked position (Figure9).
REF: TM 9-1005-313-10, WP 0021-5
SLIDE 8 OFF:
Review Summary:
Conduct a Review/Summary of the information presented in the Learning Step.
TLO - LSA 4. Learning Step / Activity TLO - LSA 4. Troubleshoot the M240L Machine Gun
Instr Type (I:S Ratio): Military - ICH (1:10)* Time of Instruction: 1 hr 30 mins
Media Type: Unassigned Other Media: Unassigned
Security Classification: This course/lesson will present information that has a Security
SLIDE 9 ON:
INSTRUCTOR NOTE: Refer students to TM 9-1005-313-23&P, WP 0015-1. Instructor can select troubleshooting procedures and walk students through the symptom, malfunction and corrective action.
SLIDE 9 OFF:
Check on Learning: SLIDE 10 ON:
Determine if the students have learned the material presented by soliciting student questions and explanations. Ask the students questions and correct misunderstandings
SLIDE 10 OFF:
Review Summary:
Conduct a Review/Summary of the information presented in
TLO - LSA 5. Learning Step / Activity TLO - LSA 5. Assemble the M240L Machine Gun.
Instr Type (I:S Ratio): Military - ICH (1:10)*
Time of Instruction: 1 hr 30 mins Media Type: Actual Equipment
Other Media: Unassigned Security Classification: This course/lesson will present information that has a Security
SLIDE 11 ON:
INSTRUCTOR NOTE: Refer students to TM 9-1005-313-10, WP 0023-1.
1) Position feed tray and cover assembly on receiver; push cover assembly downward; close cover and insert spring pin.
NOTE: Insert spring pin from right side.
2) Open top cover assembly. NOTE: Be sure to cover detent holds cover assembly open.
3) Set bolt and operating rod assembly on top of rails (inside receiver). Extend bolt to unlocked position; push the assembly all the way into the receiver. Close cover assembly and lock.
WARNING: Eye protection is required when assembling springs and operating rods.
4) Insert driving spring into operating rod assembly. Push it in fully and lower it to seat the stud in hole of receiver.
NOTE: Be sure operating rod assembly is properly seated in receiver before operating weapon. Top of buffer/buffer and spade grip/buttstock should be flush with top of receiver.
5) Install buffer assembly/buffer or spade grip assembly/buttstock and buffer assembly and make sure it latches.
6) Insert sprint pin
NOTE: Pin must be inserted from right side only.
7) Place trigger housing safety in fire "F" position; position front of housing assembly into place and pivot into position.
WARNING: Before firing, make sure the barrel is locked tightly in receiver. If the barrel is not locked tight, threads in receiver could be damaged or cause personal injury.
NOTE: Barrel must be in upright position when installing barrel.
8) Insert barrel fully into socket and push barrel release/barrel carrying handle clockwise as far as it will go.
9) Release the barrel release/barrel carrying handle and return to upright position.
10) Push barrel release /barrel carrying handle clockwise while counting the clicks (fewer than 2 or more than 7 clicks indicate defective parts) to lock.
NOTE: If barrel binds in socket or if barrel release/barrel carrying handle will not rotate when pushed, do not pound on barrel release/barrel carrying handle. Take machine gun to your maintenance activity.
SLIDE 11 OFF:
SLIDE 12 ON:
Q: What is the 1st step when reassembly of the M240L?
A: Position feed tray (Figure 1) and cover assembly (Figure 1) on receiver.
REF: TM 9-1005-313-10, WP 0023-1
Q: What is the 18th step when reassembly of the M240L?
A: Push barrel release /barrel carrying handle (Figure 6) clockwise while counting the clicks (Fewer than 2 or more than 7 clicks indicate defective parts) to lock. If barrel binds in socket or if barrel release/barrel carrying handle will not rotate when pushed, do not pound on barrel release/barrel carrying handle (Figure 6). Take machine gun to field level maintenance.
REF: TM 9-1005-313-10, WP 0023-4
SLIDE 12 OFF:
Review Summary:
Conduct a Review/Summary of the information presented in
TLO - LSA 6. Learning Step / Activity TLO - LSA 6. Perform Safety/Function Check on the M240L Machine Gun.
Instr Type (I:S Ratio): Military - ICH (1:10)*
Time of Instruction: 30 mins Media Type: Actual Equipment
Other Media: Unassigned Security Classification: This course/lesson will present information that has a Security
SLIDE 13 ON:
INSTRUCTOR NOTE: Refer students to TM 9-1005-313-10, WP 0024 00-1.
1) Place safety to "F" fire.
2) Pull cocking handle completely to rear to lock bolt back.
3) Return cocking handle to forward, locked position.
4) Check location of bolt to ensure it is fully rearward. Feed roller should line up with feed cover guide posts.
5) If roller is in front of post, place safety to “F” fire.
6) Pull cocking handle assembly (or charge cable) fully to the rear and ensure bolt locks completely to the rear.
7) Place safety to "S" safe position, depress trigger; nothing should happen.
8) Place safety to "F" fire.
9) Hold cocking handle assembly to rear.
10) Fully depress trigger.
11) Ease bolt forward to close and lock. Safety must not be able to be moved to the safe position.
SLIDE 13 OFF:
Check on Learning: SLIDE 14 ON:
Q: What is the 1st step when performing a functions check?
A: Place safety to "F" fire. (Figure 1)
REF: TM 9-1005-313-10, WP 0024 00-1
Q: What is the 4th step when performing a functions check?
A: Check location of bolt to ensure it is fully rearward. Feed roller should line up with feed cover guide posts. (Figure 2)
REF: TM 9-1005-313-10, WP 0024 00-1
SLIDE 14 OFF:
Conduct a Review/Summary of the information presented in
TLO - LSA 7. Learning Step / Activity TLO - LSA 7. Perform Maintenance on the M240L Machine Gun.
Instr Type (I:S Ratio): Military - ICH (1:10)*
Time of Instruction: 1 hr Media Type: Actual Equipment
Other Media: Unassigned Security Classification: This course/lesson will present information that has a Security
INSTRUCTOR NOTE: Provide students with a blank DA Form 5988-E from the student handout.
a. Verify the administrative information on the DA Form 5988-E.
1) Verify the DODAAC is WBAKT0.
2) Verify the organization is HHC, 13th Military Police Battalion.
3) Verify ADMIN NUM and SERIAL NUMBER of the weapon.
INSTRUCTOR NOTE: Have students enter the serial number of the weapon that they are going to
PMCS in the serial number.
4) Verify M240L is listed as the EQUIP MODEL.
5) Verify Machine Gun, 7.62mm is listed as the EQUIP NOUN.
6) Verify Quarterly is listed as the TYPE INSPECTION.
7) Verify the EQUIP NSN is 1005-01-549-5837.
8) Verify the TMs being used.
b. Conduct Field Preventive Maintenance Checks and Services on the M240L Machine Gun.
INSTRUCTOR NOTE: Refer students to TM 9-1005-313-23&P, WP 0005-00. Review the general instructions for conducting the PMCS.
1) Machine Gun
a) Field strip weapons are in accordance with TM 9-1005-313-10.
2) Barrel Assembly.
a) Check barrel for bulges, bends, burrs, and obstructions or pits in chambers or bore. Disassemble, inspect, clean (if necessary) and reassemble collar and plug. Make sure flash hider
/Suppressor is fastened securely.
b) Check for compliance with annual gaging requirements (headspace/barrel erosion). Ensure barrels are properly tagged as a set. Etching but no stamping on carrying handle is authorized.
c) Inspect front sight for looseness or any damage (bends).
NOTE: Some heat distortion, charring, and cracks may be observed on the outer non-metallic portion of the heatshield; these are not cause for replacement unless they cause edges that can cut, or enough plastic is displaced so as to allow contact with metal portions.
d) Inspect carrying handle assembly for bent, broken, or missing parts. Assure heatshield is present, remains retained on barrel assembly, and is not bent, broken or missing parts.
3) Buffer Assembly/Hydraulic Buffer Assembly.
a) Buffer Assembly
(1) Check for burs or rough edges on mating grooves and flanges. Check to make sure that back plate latch locks buffer assembly securely to receiver assembly when installed. Make sure buffer plug sticks out through back plate and flush or higher than the protrusion below it. Make sure there is no rattling sound when buffer is shaken or that the plug cannot rotate by finger pressure. Check for imprint on rear of operating rod on the buffer housing. Make sure machine plug is tight.
b) Hydraulic Buffer Assembly.
(1) Check for burrs or rough edges on mating grooves and flanges. check to make sure that back plate latch locks buffer assembly securely to receiver assembly when installed. Check buffer for leaks. Check buffer for looseness in backplate.
(2) Check buffer housing for peening, cracking or damage to include finish missing from the buffer housing stop. Check buffer shaft for bends, mushrooming, peening and cracks on the face. Check shaft for oil residue. Work the buffer assembly to check for fluid leakage. Buffer shaft should depress smoothly without chatter and return promptly when released.
c) Buttstock and Buffer Assembly.
(1) Inspect buttstock for cracks. Check to make sure backplate latch locks securely to receiver assembly when installed. check buttstock for looseness on buffer housing.
(2) Ensure buffer block is firmly attached to buttstock.
NOTE: Cracks may be observed on the outer non-metallic portions of the buttstock. These are not a cause for a replacement unless they cause edges that can cut, or enough plastic is displaced so as to allow contact with skin.
4) Driving Spring Rod Assembly.
a) Check spring for broken strands. Replace spring rod assembly if two strands are broken on the same coil or three or more strands are broken, regardless of location, on the same spring. Make sure driving spring rod assembly is not bent.
5) Bolt and Operating Rod Assembly
a) Remove pin and bolt assembly from operating rod assembly. check firing pin to make sure it is straight and has a smooth, round tip. Make sure ball end is installed between spring pin and bottom of groove. Clean and remove carbon, if necessary. Visually inspect bolt for cracks. check roller for spring action and freedom of movement. Reassemble pin and bolt assembly to operating rod assembly.
NOTE: Always turn in both barrels with the weapon if turned in with bolt assembly problems.
6) Trigger Spring Pin and Cover Hinge Spring Pin.
a) Inspect trigger spring pin and cover hinge spring pin for bends, and for missing springs. Replace pins if they are bent or if the spring pins are missing.
7) Trigger Housing Assembly.
a) Inspect tripping leaver and sear for burrs on edges or shoulders. Push back on tripping lever to raise sear.
Place safety to safe "S". Pull trigger. Sear should not drop down far enough to lock in downward position.
Place safety to fire "F". Pull trigger. Sear should drop down and lock in the downward position. Check for cracked grips. Check sear spring to maske ensure the leg of the sear spring is behind trigger pin and not between the trigger and the pin.
b) Check grip assembly for loose or missing grip screws. Check trigger guard for bends or cracks.
8) Cover Assembly.
a) Check cover assembly for cracks or distortion. Pivot feed lever back and forth to make sure the feed mechanism operates smoothly without binding. Push in on cover latches to make sure retaining clip is not weak or missing and cover latches do not bind in the housing. Push down on cartridge guides and feed pawls to make sure springs are not weak or missing. Inspect accessory mounting rail for nicks or burrs. Top cover should be able to hold up it's own weight without added weight.
b) Cover should be able to hold it's own weight without falling.
INSTRUCTOR NOTE: Inform students that during the check of the M240L Cover Assembly it was discovered that it was bent. You should stop and enter the deficiency on the DA Form 5988-E.
9) Annotate the deficiency on the DA Form 5988-E.
a) Enter [9] in the ITEM NUM column. Number is the item number from the TM.
b) Enter [22 April 20XX] in the FAULT DATE column as the date of the PMCS.
c) Enter [X] as the FAULT STATUS. The X should be circled as the deficiency is listed in the NOT FULLY
MISSION CAPABLE IF column of the TM.
d) Enter [Cover Assy is bent] in the FAULT DESCRIPTION column.
INSTRUCTOR NOTE:
support required.
Have students refer to TM 9-1005-313-23&P, WP 0042 to determine the level of
e) Enter in [DA Form 5990-E (SPT MNT)] in the CORRECTIVE ACTION column.
f) Have student enter their INSPECTORS LIC# (First initial of last name and the last five of their DOID).
INSTRUCTOR NOTE: After filling out the information for the deficiency, complete the PMCS.
10) Feed Tray.
a) Check feed tray for cracks, deformation, broken welds, and loose rivets.
11) Receiver Assembly
a) Check receiver for loose (finger tight) or missing rivets.
b) Check that rear sight assembly is securely mounted to receiver assembly and operates properly.
c) Check that manual control handle operates slide properly.
d) Check for damaged or missing ejection port cover, spring and pin.
e) Push in on barrel locking latch to make sure the latch spring is not missing or weak.
f) Check to make sure access cover is in place in the bottom of the receiver.
g) Repair or replace all damaged authorized parts.
12) Receiver Assembly with Forward Rail.
a) Check assembly for cracks; broken, loose, or missing parts.
13) Bipod Assembly.
a) Check bipod legs for cracks, twisted or incomplete assembly.
14) Machine Gun
a) Assemble weapon in accordance with TM 9-1005-313-10.
b) Be sure parts are installed correctly and are in good working condition.
c) When installing the barrel assembly in the receiver, rotate the barrel release latch/carrying handle assembly clockwise until it stops. Unlock and rotate counter-clockwise completely. While rotating clockwise, count the number of clicks until it stops. Fewer than 2 or more than 7 clicks indicate defective parts. (Make this check with spare barrel also.)
d) Check weapon functioning with belted dummy ammo.
e) Initial gaging is required 1 year from receipt of new or overhauled weapons. Ensure that machine gun has been inspected/gaged within the last year. For Army Reserve and National Guard weapons, the period is 2 years unless inspection shows need for gaging more often due to usage or other factors.
SLIDE 8 OFF:
Determine if the students have learned the material presented by soliciting student questions and explanations.
Ask the students questions and correct misunderstandings.
Review Summary:
SECTION IV. SUMMARY
Method of Instruction: Reflective Discussion
Instr Type(I:S Ratio): Military - ICH (1:30) Time of Instruction: 15 mins
Check on Learning Determine if the students have learned the material presented by soliciting student questions and explanations. Ask the students questions and correct misunderstandings.
Question: What assembly provides feeding, stripping, chambering, firing, extraction, and ejection of cartridges using the projectile propelling gases for power?
Answer: The bolt and operating rod assembly.
Question: What is the first step in clearing the machine gun M240B IAW TM 9-1005-313-10?
Answer: Place safety on ”F“.
Question: What action is required if you see rust or other signs of wear on a weapon?
Answer: PMCS should be done immediately.
Question: Which side of the weapons should the insert spring pin be entered?
Answer: Insert spring pin from the right side.
Question: When installing the barrel, what is the position of the barrel release?
Answer: The barrel release must be in the upright position.
Review/ Summary
During this lesson we covered the following areas-
a) Identify the Characteristics, Capabilities and Features, and Major Components of the M240B Machine Gun.
b) Clear the M240B Machine Gun.
c) Disassemble and Troubleshoot the M240B Machine Gun.
d) Troubleshoot the M240B Machine Gun.
e) Assemble the M240B Machine Gun.
f) Perform Safety/Function Check on the M240L Machine Gun.
g) Perform on the M240B Machine Gun.
h) Perform Maintenance on the M240L Machine Gun.
SECTION V. STUDENT EVALUATION
Testing
Feedback
NOTE: Describe how the student must demonstrate the accomplishment of the TLO. Refer student to the Student Evaluation Plan.
The student will be evaluated on disassembly/assembly procedures and conducting field maintenance on a GO/NO-GO basis. Student must receive a GO to be successful.
NOTE: Feedback is essential to improving training, always encourage students to provide comments and ensure to complete the Module AAR.
NOTE: Review the completed practical exercise with the students. Ensure lesson is understood by asking questions and receiving feedback from the students. Clear up any misunderstandings.
A-1
Appendix A - Viewgraph Masters
Perform Field Maintenance on the Machine Gun 7.62mm M240L.
101-UAC03C12 / Version 01.0 ©
Sequence Media Name Media Type
B-1
Appendix B - Assessment Statement and Assessment Plan
Assessment Statement: None.
Assessment Plan: None.
C-1
Appendix C - Practical Exercises and Solutions
PRACTICAL EXERCISE(S)/SOLUTION(S) FOR LESSON 101-UAC03C12 Version 01.0 ©
PRACTICAL EXERCISE SHEET 101-UAC03C12 PE1
Time: 1 hours 0 minutes
I:S Ratio: 1:15
Title 101-UAC03C12 M240L P.E Lesson Number/Title
101-UAC03C12 Version 01.0 © / Perform Field Maintenance on the Machine Gun 7.62mm M240L.
Security Classification Unclassified
Introduction INTRO
Motivator Soldiers draw weapons from the arms room.
Terminal Learning Objective
Safety
Risk Assessment Level
Environmental Considerations
NOTE. Inform the students of the following Terminal Learning Objective requirements.
At the completion of this lesson, you [the student] will:
Action: Perform Field Maintenance on the Machine Gun 7.62mm M240L.
Conditions:
In a classroom environment, given the requirement to perform field maintenance on the M240B Machine Gun. Given TM 9-1005-313-10, TM 9-1005-313-23&P, DA Pamphlet 750-8, a DA Form 5988-E, DA Form 5990-E, armorer tool kit, safety equipment, M240B Machine Gun, and linked dummy rounds.
Standards:
Perform field maintenance on the M240L Machine Gun by finding all deficiencies without losing accountability, without error.
General classroom, weapon and electrical equipment safety procedures will be followed. Before starting an inspection and/or performing any maintenance procedures, be sure to clear the weapon. During the clearing procedure always keep the weapon pointed in a safe direction. A potential safety hazard exists if the weapon is assembled or disassembled incorrectly. Do not attempt to disassemble or assemble this weapon until the Instructor tells you to do so, nor should you attempt to adjust or remove the sight from this weapon unless specifically directed by the Instructor in the classroom. Students will ensure that safety goggles are worn at all times during the disassembly and assembly of this weapon.
Low
NOTE: Instructor should conduct a risk assessment to include environmental considerations IAW the current environmental considerations publication, and ensure students are briefed on hazards and control measures.
NOTE: Instructor should conduct a risk assessment to include environmental considerations
C-2
IAW the current environmental considerations publication, and ensure students are briefed on hazards and control measures.
Instructional Lead-in NOTE: It is the responsibility or all Soldiers, DA Civilians, and Contractors to protect the environment from damage.
NOTE: Have dirty rags turned in to the supply room and cleaned on a weekly basis.
Evaluation The soldier will complete hands on performance based examination covering the materials presented in this lesson. The exam will be graded on a GO/NO-GO basis. Student must receive a GO to be considered successful.
Instructional Lead-in
Resource
Special Instructions
Explain to the Student that performing organizational maintenance on small arms is similar to performing maintenance on a car. It is important to keep your car in good running condition so you can get back and forth to work. In the U.S. Army, weapons must be maintained to specified standards so the unit can successfully perform its mission.
Instructor Materials:
Rifle, Sniper: M110 Remarks:
5180-00-357-7770 - 1:1 0:0 No No Tool Kit, Repairman's, Small Arms Remarks:
7021-01-C14-3190 - Computer, Micro Lap- 1:10 0:0 No No Top Portable AC:
M4500 Dell Remarks: 1 on monitor table
Student Materials:
PENCIL
PAPER
Procedures
SPECIAL INSTRUCTIONS
1. This is a hands-on practical exercise. You will use only the reference publications shown. You may use notes. Do not talk to other students at any time. Speak only to the instructor.
C-3
2. Be sure to read the “SITUATION”. If you have any questions, ask the instructor now.
3. The soldier will score a GO (G) if all steps are passed. The soldier will score a NO-GO (NG) if any steps are failed.
If the soldier scores a NG on any step, the soldier will be shown what was done incorrectly, how to do it properly, and then will be re-tested.
4. During this practical exercise you will need:
Feedback
SEE STEP 23 FOR PE
NOTE: Feedback is essential to improving training, always encourage students to provide comments and ensure to complete the Module AAR.
NOTE: Review the completed practical exercise with the students. Ensure lesson is understood by asking questions and receiving feedback from the students. Clear up any misunderstandings.
C-4
SOLUTION FOR
PRACTICAL EXERCISE 101-UAC03C12 PE1
SEE STEP 23
D-1
Appendix D - Student Handouts
Perform Field Maintenance on the Machine Gun 7.62mm M240L.
101-UAC03C12 / Version 01.0 ©
Sequence Media Name Media Type
2 M240L PE DOCX
| CRM LESSON PLAN REPORT |
| SECTION I. ADMINISTRATIVE DATA |
| ARMY LEARNING MODEL |
| OE INTEGRATION |
| SECTION II. INTRODUCTION |
| SLIDE 92Y10D11-1 (ON) |
| SLIDE 92Y10D11-1 (OFF) SLIDE 92Y10D11-2 (ON) |
| SLIDE 92Y10D11-2 (OFF) |
| SECTION III. PRESENTATION |
| SLIDE 3 OFF: |
| SLIDE 4 ON: |
| REF: TM9-1005-313-10. WP 0002-3 & WP |
| REF: TM 9-1005-313-10. WP 0002-3 & WP 0002-4 |
| SLIDE 5 ON: |
| SLIDE 5 OFF: |
| REF: TM 9-1005-313-10, WP 0005-1 |
| REF: TM 9-1005-313-10, WP 0005-3 |
| SLIDE 7 ON: |
| SLIDE 7 OFF: |
| SLIDE 8 ON: |
| REF: TM 9-1005-313-10, WP 0021-1 |
| REF: TM 9-1005-313-10, WP 0021-5 |
| SLIDE 9 ON: |
| SLIDE 9 OFF: |
| SLIDE 10 OFF: |
| SLIDE 11 ON: |
| SLIDE 11 OFF: |
| SLIDE 12 ON: |
| REF: TM 9-1005-313-10, WP 0023-1 |
| REF: TM 9-1005-313-10, WP 0023-4 |
| SLIDE 13 ON: |
| SLIDE 13 OFF: |
| REF: TM 9-1005-313-10, WP 0024 00-1 |
| REF: TM 9-1005-313-10, WP 0024 00-1 |
| SECTION IV. SUMMARY |
| SECTION V. STUDENT EVALUATION |
| PRACTICAL EXERCISE SHEET 101-UAC03C12 PE1 |
| SPECIAL INSTRUCTIONS |
SOLUTION FOR
File details come from the government source that posted it. Updated .