101-UAC03C08v_01_0 PERFORM FIELD MAINTENANCE ON THE MACHINE GUN CALIBER .50 M2A1.pdf
PDF 327 KB Posted
- Attached to
- Small Arms Maintenance (SAM 31)
- Solicitation number
- W912PB-27-Q-A004
About this file
This document is a Curriculum Requirement Module (CRM) lesson plan report for Army training on performing field maintenance on the .50 caliber M2A1 machine gun.
The lesson introduces newly designated unit armorers to field maintenance procedures for the M2A1 Machine Gun in accordance with TM 9-1005-347-10, TM 9-1005-347-23&P, and DA Pam 750-8. The training is designed to enable students to perform field maintenance operations without supervision and identify all deficiencies while maintaining weapon accountability. The lesson supports Army Learning Area professional competence and General Learning Objective 14 regarding technical and tactical competence. The training requires 5 hours and 0 minutes of resident instruction (administrative/academic hours) plus 3 hours and 20 minutes of instructor action time. Instruction methods include discussion, demonstration, reflective discussion, and hands-on practical exercises delivered at a 1:30 military instructor-to-student ratio. Required equipment includes one M2A1 Machine Gun, one M3 tripod mount, armorer toolkit, safety goggles, classroom laboratory space (3,000 square feet), two laptop computers, one iPad tablet, one printer, one interactive display, and dummy ammunition (A560). Student evaluation occurs on a GO/NO-GO basis for disassembly/assembly procedures and field maintenance conduct. The lesson covers weapon characteristics, clearing procedures, disassembly, troubleshooting, assembly, function checking, headspace and timing verification, and preventive maintenance checks and services (PMCS), including completing DA Form 2404 maintenance documentation. The training material is classified as unclassified and is restricted to U.S. Government agencies and contractors only; it cannot be used to instruct international military students per FD3 foreign disclosure restrictions.
View the file
Other files
Show all 14
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
CUI
CRM LESSON PLAN REPORT
PERFORM FIELD MAINTENANCE ON THE MACHINE GUN, CALIBER .50, M2A1
101-UAC03C08 / 01.0 ©
Approved 08 Aug 2025
Effective Date: 08 Aug 2025
SCOPE:
This lesson introduces the newly designated unit armorer on how to perform Field Maintenance on the Machine Gun, Caliber .50, M2A1. The expected learning outcomes is for the student to be able to perform Field Maintenance on the M2A1 Machine Gun in accordance with TM 9-1005-347-10, TM 9- 1005-347-23&P and DA Pam 750-8, finding all deficiencies without losing accountability. This lesson supports the Army Learning Area (ALA) of professional competence, and General Learning Outcome (GLO) 14, Soldiers and Civilians are technically and tactically competent. The goal of this lesson is to provide the Student with the knowledge and skills to perform Field Maintenance on the M2A1 Machine Gun without supervision and to the standards outlined in TM 9-1005-347-10, TM 9-1005- 347-23&P, DA Pam 750-8 and ARIMS User Guide.
Distribution Restriction: Distribution authorized to U.S. Government agencies and their contractors only export controlled; critical technology. This determination was made on 17 May 2011.
Insert 6501 E. 11Mile rd., Detriot Aresenal, MI 48397-5000 Destruction Notice: Destroy by any method that will prevent disclosure of contents or reconstruction of the document Foreign Disclosure: FD3 - This training product has been reviewed by the developers in coordination with the Forg Gregg adams foreign disclosure officer. This training product cannot be used to instruct international military students.
SECTION I. ADMINISTRATIVE DATA
All Course Masters/POIs Including This Lesson
Courses
Course Number
None
POIs
Version Title Phase Status
Task(s) Taught(*) or Supported
Reinforced Task(s)
Knowledge
Skill
Administrative/ Academic Hours
Instructor Action
Test Lesson(s)
Prerequisite
POI Number Version Title Phase Status
Task Number Task Title Status
Task Number
Task Title
Status
Knowledge Id
K22092
Title
Understand general PMCS principles and procedures
Taught
Yes
Required
No
Skill Id
101-S-M014
Ability to perform PMCS on equipment used.
Taught
No
The administrative/academic (50 min) hours required to teach this lesson are as follows:
Academic Resident Hours / Methods
Yes Yes
0 hrs 0 hrs 3 hrs 0 hrs
30 mins 15 mins 25 mins 30 mins
Discussion (Small or Large Group) Reflective Discussion Demonstration Practical Exercise (Hands-On/Written)
Total Hours(50 min): 5 hrs 0 mins
The instructor action (60 min) hours required to teach this lesson are as follows:
Hours/Actions
Lesson(s)
0 hrs 15 mins Classroom Breakdown
0 hrs 15 mins Classroom Setup 1 hrs 0 mins Logistics Support – Weapon 0 hrs 25 mins Student Counseling 1 hrs 0 mins Student Re-test 0 hrs 25 mins Student Re-train
Total Hours (60 min): 3 hrs 20 mins
Lesson Number Version
Lesson Title
Lesson Number Version
Lesson Title
Training Material Classification
Security Level: This course/lesson will present information that has a Security Classification of: U - Unclassified.
Foreign Disclosure Restrictions
References
FD3. This training product has been reviewed by the developers in coordination with the Forg Gregg adams foreign disclosure officer. This training product cannot be used to instruct international military students.
Student Study Assignment None
Requirements
Support Personnel
Additional Support Personnel
Primary Instructor and Assistant Instructor(s)
Armorer Computer System Analyst
Student
Man
Number
Date
ARIMS User Guide Army Records Information Management System (ARIMS) User Guide
04 Aug 2022
DA PAM 750-8 The Army Maintenance Management System (TAMMS) Users Manual
22 Aug 2005
TM 9-1005-347-10 Operator’s Manual for Machine Gun, Caliber .50;
M2A1, with Fixed Headspace and Timing (1005-01- 511-1250)
08 Apr 2011
TM 9-1005-347-23&P Machine Gun, Caliber .50: M2A1 w/Fixed Headspace and Timing, NSN 1005-01-511-1250 (EIC 4AZ)
29 Jul 2011
Name Ratio Qty Hours
Armorer Remarks:
0:0 1 1.0
Computer System Analyst Remarks:
0:0 1 8.0
Equipment for Instruction
ID - Name Student
Materials
(Note: Asterisk before ID indicates a TADSS.)
Instructor Materials:
a. Lesson Plan.
b. Practical Exercise (PE)
c. Practical Exercise Solution.
d. Required Publications.
e. Safety Goggles.
Student Materials:
a. Student Handout (Blank Forms)
b. Practical Exercise (PE)
c. Required Publications.
d. Pen or pencil.
e. Safety Goggles.
Classroom, Training Area, and Range
ID - Name Quantity Student Ratio
Setup Mins
Cleanup Mins
Requirements 17135-3000 Laboratory Instructional Building, 3000 Square Foot
1:30 20 30
Ratio Ratio Spt Qty Exp
1005-00-322-9716 - Mount, Tripod, Machine Gun, .50 Caliber: M3 Remarks:
1:6 0:0 No 1 No
1005-01-511-1250 - Machine Gun Caliber M2A1 RIFLE Remarks:
1:1 0:0 No 1 No
4240-01-504-0052 -
GOGGLES,INDUSTRIAL
Remarks:
1:1 1:1 No 0 No
5180-00-357-7770 - Tool Kit, Repairman's, Small Arms Remarks:
1:10 0:0 No 1 No
7021-01-C14-3190 - Computer, Micro Lap-Top Portable AC: M4500 Dell Remarks:
0:0 0:0 No 2 No
7021-01-D01-0269 - PC Tablet, Data Entry: IPAD 2 WIFI 64GB Apple Remarks:
1:1 0:0 No 1 No
7025-01-C11-4208 - Printer, Daisy Wheel/Dot Matrix/:2335DN MFP Dell Remarks:
0:0 0:0 No 1 No
7050-01-C14-4309 - Interactive Pen Display: ID422W Smart Remarks:
0:0 0:0 No 1 No
7490-01-T00-0291 - Card Programmer: RFC-03G Turning Technologies Remarks:
1:1 0:0 No 0 No
7490-01-T00-0292 - Card Programmer: XRC-R02 Turning Technologies
1:30 0:0 No 0 No
Ammunition Requirements DODIC - Name Exp
Student
Instruct
Spt Qty
A560 - Dummy Cartridge, Caliber .50, M2 (Not Linked)
N 5:1 5:1
Instructional Guidance/ Conduct of Lesson
NOTE: Before presenting this lesson, instructors must thoroughly prepare by studying this lesson and identified reference material.
NOTE: Instructor/Facilitator will ensure to incorporate OE experiences.
ARMY LEARNING MODEL
All Instructors/Facilitators will facilitate training under Army Learning Model. Ensuring training is based on quality, relevance and effectiveness of face-to-face learning experiences through outcome-oriented instructional strategies. This type of instruction will foster critical thinking, initiative and operational relevance in context.
OE INTEGRATION
Instructors/Facilitators will facilitate conversations from students and relate this lesson to current Operational Environments (OE) using personal experiences and/or examples obtained from the Center for Army Lessons Learned (CALL). Instructors should provide sufficient OE variables and scenarios to produce the desired soldier training outcome for this lesson.
NOTE: Verify that the training material is loaded in the computers before beginning the lesson.
Proponent Lesson Plan Approvals Name Rank Position Date michelle.r.brown8.civ Not available Approver 08 Aug 2025
SECTION II. INTRODUCTION
Method of Instruction: Discussion (Small or Large Group) Mode of Delivery: Resident Instruction
Instr Type (I:S Ratio): Military - ICH (1:30) Time of Instruction: 15 mins
Motivator INSTRUCTOR NOTE: Have students draw the M2A1 Machine Gun from the arms room.
SLIDE 92Y10D09-1 (ON)
Introduce the Perform Field Maintenance on the Machine Gun, Caliber .50: M2A1 W/Fixed Headspace and Timing to the students.
The Commander has designated you as his or her Unit Armorer, responsible for the field maintenance of small arms. As a Unit Armorer, you will prepare, maintain, submit, and file all maintenance requirements for the unit's organizational weapons. You must have the skill set and the ability to perform all field maintenance tasks. The Unit Armorer is an important job and requires attention to detail. If the M2A1 Machine Gun is not maintained to required standards, the weapon may not operate, unit readiness will be degraded, and your unit may not be prepared to perform its mission.
SLIDE 92Y10D09-1 (OFF)
SLIDE 92Y10D09-2 (ON)
INSTRUCTOR NOTE: Review the lesson Terminal Learning Objective with the students.
SLIDE 92Y10D09-2 (OFF)
Terminal Learning Objective
NOTE. Inform the students of the following Terminal Learning Objective requirements.
At the completion of this lesson, you [the student] will:
Action: Perform Field Maintenance on the Machine Gun, Caliber .50, M2A1.
Conditions:
In a classroom environment, given the requirement to perform field maintenance on the M2A1 Machine Gun. Given TM 9-1005- 347-10, TM 9-1005-347-23&P, DA Pam 750-8, a DA Form 2404, armorer toolkit, safety equipment, and a M2A1 Machine Gun.
Standards:
Perform field maintenance on the M2A1 Machine Gun by finding all deficiencies without losing accountability, without error.
Learning Domain - Level: Psychomotor - Imitation
No JPME Learning Areas Supported: Supports GLO 10 & 11.
Safety
General classroom, weapon, and electrical safety procedures will be followed.
Before starting and/or performing any maintenance procedures, be sure to clear the weapon.
During the clearing procedure always keep the weapon pointed in a safe direction.
A potential safety hazard exists if the weapon is assembled or disassembled incorrectly. Do not attempt to disassemble or assemble this weapon until the Instructor tells you to do so.
Students will ensure that safety glasses are worn at all times during the assembly and disassembly of the weapon.
Risk Assessment Level
Low - Eye Hazard Assessment: Caused by mishandled springs
Controls: Ensure springs are properly handled and eye protection is worn.
Leader Actions: Supervise and ensure guidance is followed by the students.
Environmental Considerations NOTE: Instructor should conduct a risk assessment to include environmental considerations
IAW the current environmental considerations publication, and ensure students are briefed on hazards and control measures.
NOTE: It is the responsibility of all Soldiers, DA Civilians, and Contractors to protect the environment from damage.
NOTE: Have dirty rags turned into the supply room and cleaned on a weekly basis.
Instructional Lead-in Explain to the Student that performing field maintenance on small arms that it is similar to performing maintenance on a car. It is important to keep your car in good running condition so you can get back and forth to work. In the U.S. Army, weapons must be maintained to specified standards so the unit can successfully perform its mission.
SECTION III. PRESENTATION
TLO - LSA 1. Learning Step / Activity TLO - LSA 1. Identify the Characteristics, Capabilities, Features and Major Components of the M2A1 Machine Gun.
Method of Instruction: Discussion (Small or Large Group)
Instr Type (I:S Ratio): Military - ICH (1:10)*
Time of Instruction: 15 mins Media Type: Actual Equipment / PowerPoint Presentation Other Media: Unassigned
Security Classification: This course/lesson will present information that has a Security Classification of: U - Unclassified.
Note: Marked as (*) is derived from the parent learning object
SLIDE 3 ON:
PROJECTION UNIT: Instructor can use overhead projector to display appropriate TM pages as they are discussed.
a. Purpose of Equipment. To provide automatic weapon suppression fire for offensive and defensive purposes. This weapon can be used effectively against personnel, light armored vehicles, and low flying
/slow flying aircraft. The caliber .50, M2A1, is installed on mounts of several different types of combat vehicles and ships.
INSTRUCTOR NOTE: Refer students to TM 9-1005-347-10, WP 0002 00-2
b. Location and Description of Major Components.
1) The M2A1 Machine Gun (Flex Type) is composed of the following:
a) Front and Rear Sights
b) Barrel
c) Receiver
d) Retracting Slide Handle
e) Trigger/Trigger Block
2) M2A1 Unique Components.
a) Knurled Plain Nut
b) Timing Lock Screw
c) Barrel Support
d) Barrel Carrying Handle Assembly
e) Barrel Assembly
f) Barrel Extension Assembly
g) Breech Lock
h) Backplate Assembly
C. Equipment Characteristic, Capabilities, and Features
1. The .50 Caliber Machine Gun, M2, is a link-belt fed, recoil-operated, air-cooled, crew-served machine gun. The machine gun is capable of firing single-shot and automatic; is capable of right-hand or left-hand feed and includes a backplate trigger block assembly. It is used as a ground gun mounted on M3 tripod mount, MK 93 mount, M205 lightweight tripod mount or is installed on a M66 ring mount of several types of combat vehicles.
2. The M2A1, .50 caliber Machine Gun operates in the same manner as the standard .50 caliber machine gun. However, it offers added features, which include fixed headspace and timing, quick change barrel, and backplate trigger block assembly.
3. All major components of the .50 Cal. M2A1 are interoperable. The Barrel Extension Assembly and Bolt have been serialized to remain together as an assembly. If any parts of the Barrel Extension or Bolt is interchanged, headspace and timing must be reset.
NOTE: Do not attempt to remove the Breech Lock from the Barrel Extension. It is not intended for the
Breech Lock to be removed during cleaning. Pinning the Breech Lock ensures that the assigned Breech
Lock/Barrel Extension combination is maintained, thus insuring proper headspace.
4. The .50 Caliber Machine Gun, M2 Barrel, Fixed M48 Turret Type is a link-belt- fed, recoil-operated, air cooled, crew-served machine gun. The machine gun is capable of firing automatic only; is capable of right-handed or left-handed feed and is mounted on a M1, M1A1, or M1A2 System Equipment Package (SEP)
Abrams Main Battle Tank commander’s station.
5. The .50 Caliber Machine Gun, M2, Barrel, is a link-belt-fed, recoil operated, air-cooled, crew-served machine gun, is a capable of right- hand or left- handed feed, and is mounted on the MK93 MOD 2( Army) or
MK93 MOD 2.
6. The M3 tripod mount is a portable, folding mount that permits a high degree of accuracy and control of fire.
7. MK93 MOD 2 (Army) is a component assembly designed as a defensive ground mouth for the MK19
MOD 3 and M2 Heavy Barrel (HB) machine guns onto the High Mobility Multipurpose Wheeled Vehicle
(HMMWV) ring assembly. It is composed of MK93 MOD 0 machine gun mount .50 caliber ammunition holder assembly, mounting bracket, catch bag assembly Universal Pintle Adapter (UPA), and traverse and
Elevation (T&E) mechanism.
8. MK93 MOD 2 is a component assembly designed as assembly designed as a mount for the MK19 MOD
3, M2 HB, and M240B (with adapter) machine gun to fit on an MK16 MOD 8 stand or on a n MK16 MOD 9 stand assembly ( a tripod with the MK16 MOD 8 stand attached). The MK93 MOD 2 and MOD 4 machine gun mount comes with ammunition holder assembly, 250-round ammunition can, and horizontal and vertical stow bar assemblies.
9. M205 Lightweight Tripod Mount for the M2 heavy barrel machine gun. M2A1 machine gun and the MK19 grenade machine gun is composed of a traverse and elevation(T&E) assembly, pintle, right rear leg, left rear leg, front leg, and tri-head assemblies. The tripod can be carried, deployed, emplaced, and stowed in its carrying configuration by a sole operator without the use of tools.
D. Principles of Operation.
1) BARREL ASSEMBLY- Composed of barrel and barrel carrier assembly. Barrel carrier assembly permits quick removal or installation of barrel and is secured to locking and retaining grooves or barrel.
2) TRIGGER BLOCK-located at the top of the backplate assembly.
WARNING: During reassembly, the bolt and barrel extension serial numbers must match the last four digits of the receiver serial number to maintain headspace and prevent gun malfunctions and serious injury.
3) BARREL EXTENSION ASSEMBLY- Includes a breech lock specifically fitted to maintain the M2A1 fixed headspace. If any parts of the Barrel Extension or Bolt are interchanged, headspace and timing must be reset.
4) FLASH SUPPRESSOR- The Flash Suppressor reduces muzzle flash when firing. Installed on the of the
Barrel.
5) BARREL CAP- Placed on Barrel for protection and when using BFA
6) BARREL SUPPORT ALIGNMENT AND J SLOTS- correctly align and secure the M2A1 quick change barrel.
7) INTERRUPTED THREADS- All for quick barrel changes without prolonged operator exposure.
8) BARRELL ALIGNMENT PIN- Mates with the alignment and retention slots to properly position the quick change barrel.
9) FIX TIMING LOCK SCREW and ADJUSTMENT NUT- Provides fixed timing in conjunction with the quick change barrel and fixed headspace.
SLIDE 3 OFF:
Check on Learning: SLIDE 4 ON:
What is the weight of the 50 M2A1?
answer: 84lbs (38.10 kg) (TM 9-1005-213-10, pg. 0002-7
SLIDE 4 OFF:
Review Summary:
Conduct a Review/Summary of the information presented in the Learning Step.
TLO - LSA 2. Learning Step / Activity TLO - LSA 2. Clear the M2A1 Machine Gun.
Method of Instruction: Demonstration
Instr Type (I:S Ratio): Military - ICH (1:10)*
Time of Instruction: 10 mins Media Type: Actual Equipment / PowerPoint Presentation Other Media: Unassigned
Security Classification: This course/lesson will present information that has a Security
SLIDE 5 ON:
INSTRUCTOR NOTE: Refer students to TM 9-1005-347-10, WP 0005-1
1. Point weapon in a safe direction.
2. Place safety or trigger block on “S”( Safe).
3. Place the weapon in the single-shot mode.
4. Look away from the cover in a safe direction and away from the weapon.
5. Raise cover.
6. Lift the cartridge extractor and remove the ammunition belt from the feedway.
7. Lower cartridge extractor and close over.
WARNING: Round may fall to surface and possibly explode.
8. Pull and lock the bolt to the rear, leaving the retracting slide handle to the rear
9. Raise cover
10. The gunner must ensure gun is clear by visually inspecting the chamber and T-slot for rounds. In darkness, the gunner must feel inside the chamber and T-slot to ensure they are clear.
11. Depress the bolt latch release then release and ease the bolt forward wit retracting slide handle.
12. Close the cover.
13. If weapons is to be stored, depress the trigger to release spring compression.
SLIDE 5 OFF:
Check on Learning: SLIDE 6 ON:
How many steps are there in clearing the 50 M2A1?
Answer: 13 (TM 9-1005-347-10, WP 0005-1)
SLIDE 6 OFF:
Review Summary:
Conduct a Review/Summary of the information presented in
TLO - LSA 3. Learning Step / Activity TLO - LSA 3. Disassemble the M2A1 Machine Gun.
Instr Type (I:S Ratio): Military - ICH (1:10)*
Time of Instruction: 25 mins Media Type: Actual Equipment / PowerPoint Presentation Other Media: Unassigned
Security Classification: This course/lesson will present information that has a Security
SLIDE 7 ON:
a. Field Strip the M2A1 Machine Gun
INSTRUCTOR NOTE: Refer students to TM 9-1005-347-10, WP 0024 00-1
WARNING: To avoid accidental firing, remove ammunition, clear weapon, and verify that chamber is clear.
WARNING: Heat protective mitten should be used when barrel is hot to avoid injury to personnel.
1) M2/M2A1 Machine Gun and Fixed M48- Retract bolt approximately 3/8 in. for barrel locking lug to center in barrel locking spring hole on right hand side of the receiver.
2) M2 and M48: Unscrew and remove barrel assembly.
3) M2A1 Only: Rotate the barrel using barrel carrying handle until the barrel alignment pin engages alignment slot. The barrel is now unlocked from the barrel extension.
4) Pull barrel forward and remove from receiver.
WARNING:
- Never remove the backplate assembly from any weapon until the chamber has been cleared.
- DO NOT attempt to charge weapon without backplate installed to the machine gun.
- DO NOT attempt to remove backplate unless the bolt is in the forward position.
- Failure to comply with above warning may result in injury or death to personnel. Seek immediate medical attention if injury occurs.
5) Ensure the bolt latch release is in unlocked position.
WARNING:
- DO NOT stand behind machine gun while removing backplate. Failure to comply may result in injury or death to personnel. Seek immediate medical attention if injury occurs.
6) Pull backplate latch lock straight back while lifting up on backplate latch.
7) Raise backplate assembly straight up and remove from receiver.
8) Push rear of drive spring rod assembly forward and to the left until free from the side of receiver.
9) Remove drive spring rod assembly.
10) Remove M10 charge cover.
11) Retract bolt assembly far enough to align bolt stud with bolt stud hole in receiver.
12) Remove bolt stud.
13) Remove bolt assembly from receiver.
14) Rotate cartridge extractor upward and remove from left side of bolt.
15) Remove bolt switch by lifting straight up from bolt.
16) Place cocking lever in its rearmost position.
17) Release firing pin spring by pressing down on sear with swab holder section.
18) Using swab holder section, removing cocking lever pin and cocking lever.
19) M2A1 only: Using thin edge of cocking lever, rotate sear stop and pin to center of recess and bolt.
20) M2A1 only: Turn bolt over and use thin edge of cocking lever to press sear stop and pin from bottom of bolt.
21) M2A1 only: With top bolt up, use thin edge of cocking lever to pry up and remover sear stop and pin.
22) Using thin edge of cocking lever, rotate accelerator stop lock to center of recess in bolt.
23) Pry up accelerator stop lock and remove accelerator stop lock.
24) Turn bolt over and use thin end of cocking lever to pry accelerator stop from bottom of bolt.
25) Depress sear and remover dear slide.
26) Remove sear and sear spring.
27) Tip the front end of bolt upward and remove firing pin extension assembly and firing pin.
28) Removing firing pin from firing pin extension assembly.
29) Insert pointed end of clearing rod into hole in receiver.
30) Depress buffer body lock with clearing rod while apply rearward pressure on barrel extension assembly.
31) Remove barrel buffer assembly and barrel extension assembly together.
32) Separate the barrel buffer assembly and barrel extension assembly by pushing forward on tips of buffer accelerator.
33) Remover buffer assembly by pushing it out toward the rear of barrel buffer body.
34) Drive accelerator pin assembly from barrel buffer body with swab holder.
35) Remove buffer accelerator.
36) M2 and M48 only: Use pointed end of clearing rod to remove breech lock pin assembly and breech lock from extension assembly.
37) Remove safety wire or retaining from belt hold pawl pin.
38) Remove belt holding pawl pin.
39) Remove front cartridge stop and rear cartridge stop assembly.
CAUTION: Hold down on belt holding pawl assembly to prevent loss of spring. Failure to comply may result in malfunction or damage to equipment.
40) Remove belt holding pawl pin, belt holding pawl assembly, and two springs.
SLIDE 7 OFF:
Check on Learning: SLIDE 8 ON:
SLIDE 8 OFF:
Conduct a Review/Summary of the information presented in
TLO - LSA 4. Learning Step / Activity TLO - LSA 4. Troubleshoot the M2A1 Machine Gun
Instr Type (I:S Ratio): Military - ICH (1:10)*
Time of Instruction: 25 mins Media Type: Unassigned
Other Media: Unassigned Security Classification: This course/lesson will present information that has a Security
SLIDE 9 ON:
b. Troubleshoot the M2A1 Machine Gun.
INSTRUCTOR NOTE: Refer students to TM 9-1005-347-23&P, WP 0004 00-1.
Review the Troubleshooting Index with the students. Pick a symptom from Symptom Index; Walk students through the troubleshooting process.
SLIDE 9 OFF:
Check on Learning: SLIDE 10 ON:
SLIDE 10 OFF:
Conduct a Review/Summary of the information presented in
TLO - LSA 5. Learning Step / Activity TLO - LSA 5. Assemble the M2A1 Machine Gun.
Instr Type (I:S Ratio): Military - ICH (1:10)*
Time of Instruction: 30 mins Media Type: Actual Equipment / PowerPoint Presentation Other Media: Unassigned
Security Classification: This course/lesson will present information that has a Security
SLIDE 11 ON:
INSTRUCTOR NOTE: Refer students to TM 9-1005-213-23&P, WP 0011-17
WARNING: During reassembly, the bolt and barrel extension serial numbers must match the last four digits of the receiver serial number to maintain headspace and prevent gun malfunctions and serious injury.
ASSEMBLE
1) Install Extractor Switch Tenison Spring in recess inside Receiver Install Extractor Switch through
Receiver and secure with Plain Slotted Nut. Install Cotter Pin.
2) M2 and M2A1 only: Ensure Operating Head of Bolt Latch Spring Tool Assembly is screwed counterclockwise into Bracket before sliding it into Backplate grooves in Receiver.
3) M2 and M2A1 only: Install Bolt Latch Assembly in Receiver. Slide Bolt Latch Spring Tool Assembly into Backplate grooves until Stop contacts top of Receiver.
4) M2 and M2A1 only: Screw in Bolt Latch Sprong Tool Assembly Clockwise, compressing Helical
Compression Spring so that Plain Round Nut can be installed on Bolt Latch Assembly. Screw Plain Round
Nut Two turns onto Bolt Latch Assembly threads.
5) M2 and M2A1 only: UnScrew in Bolt Latch Spring Tool Assembly counterclockwise. Ensure Bolt Latch
Assembly is held on by Plain Round Nut.
6) M2 and M2A1 only: Lift up on Manual Control Lever until it is level with top Receiver. Screw in on Bolt
Latch Spring Tool Assembly clockwise and compress Helical Compression Spring.
7) M2 and M2A1 only: Tighten Plain Round Nut with spanner wrench. Line up slot in Plain Round Nut with hole in Bolt Latch Assembly Eccentric Pin.
8) M2 and M2A1 only: Install new Cotter Pin and spread ends to secure. Ensure Cotter Pin is installed from the bottom.
9) M2 and M2A1 only: Unscrew Bolt Latch Spring Tool Assembly counterclockwise and slide out of
Receiver.
10) M2 and M2A1 only: Install Retracting Slide Assembly into Receiver and secure with three Machine
Screws. Form inside Receiver, install tow Tee-Head Shoulder Bolts. Ensure that beveled edges of tee-head shoulder bolts face in opposite directions. Tighten two slotted Plain Nuts and install two new Cotter Pins.
11) M2 and M2A1 only: Install Front Sight and Gunsight Cover to Receiver and secure with two Straight
Headed Pins.
WARNING
Spring- loaded parts are an eye hazard. To avoid injury to your eyes, use care when removing and installing spring-loaded parts. Wear adequate eye protection. Failure to comply can result on serious injury to personnel.
12) Install Helical Compression Spring and Cover Detent Pawl on Receiver.
13) If removed, install new Cotter Pin in lock located at front of Receiver.
14) M2 and M2A1 only: Install Rear Sight Assembly on top of Receiver and secure front end with two
Machine Screws.
15) M2 and M2A1 only: Installed Adjustable Trigger Lever Stop Assembly inside receiver and align locating holes in Receiver and Rear Sight Assembly Adjustable Trigger Lever Stop Assembly to Receiver.
16) M2 and M2A1 only: Stake two Machine Screws.
17) M2 only: Stake Externally Relieved Screw.
18) Install Trigger Lever directly under Timing Nut in Receiver.
19) Align hole in Trigger Lever with mounting hole in Receiver.
20) Place Trigger lever Pin, loop end vertical, in assembly hole on left side plate of Receiver.
21) Match key on Trigger Lever Pin with keyway inside plate of Receiver and install Trigger Lever Pin completely.
22) Rotate Trigger Lever Pin 90 degrees to lock securely in place and fold down out of the way.
23) Check that Trigger Lever moves freely.
WARNING: Spring-loaded parts are an eye hazard. To avoid injury to your eyes, use care when removing and installing spring-loaded parts. Wear adequate eye protection. Failure to comply can result in serious injury to personnel.
24) Seat two Belt Holding Pawl Springs in place on Receiver.
25) Place Belt Holding Pawl Assembly on Belt Holding Pawl Springs Compress Belt Holding Pawl Springs and insert Belt Holding Pawl Pin.
26) Left- Hand Feed only: Place Rear Cartridge Stop Assembly and Front Cartridge Stop on Receiver.
27) Left Hand Feed only: Install Belt Holding with hooked end to rear.
28) Right-Handed Feed only: Place Front Cartridge Stop, Link Stripper, and Rear Cartridge Stop on
Receiver.
29) Right- Handed Feed only: Install Belt Holding Pawl Pin with hooked end to rear.
30) If removed, install new Barrel Locking Spring in Barrel Extension Assembly until it reaches the end of its grooves. Swage barrel extension assembly into notch of spring one place only. Barrel extension is acceptable with up to four swages per side (rivet side of barrel locking spring). Swaging that does not does not damage, prevent assembly, or impair normal operation is acceptable.
31) M2 and M48 only: Install Breech Lock in barrel extension assembly with double beveled edge up and to the front of Barrel Extension Assembly.
32) M2 and M48 only: Install Breech Lock in barrel extension assembly. Ensure both ends of Breech Lock
Pin are flush with sides of Barrel Extension Assembly.
33) Hold Barrel Buffer Assembly with Buffer Accelerator up and engage notch on shank of Barrel Extension
Assembly with cross groove in piston rod of Barrel Buffer Assembly.
34) Align Breech Lock Depressors with Buffer Accelerator up and engage notch on shank of Barrel
Extension Assembly with cross groove in piston rod of Barrel Buffer Assembly.
M2A1 Only: Ensure the Bolt and Barrel Extension Assembly serial number match the last four digits of the
Receiver serial number to prevent losing headspace, which can result in serious injury to personnel and MG damage.
35) Install Barrel Buffer Assembly and Barrel Extension Assembly in Receiver.
To avoid incorrect installation Bolt Assembly, DO NOT trip Buffer Accelerator. Failure to comply can result in machine gun damage. Ensure Cocking Lever s forward before installing Bolt Assembly into Receiver.
36) Raise Bolt Latch and push Bolt Assembly into Receiver.
37) Remove Barrel Extension Assembly and Barrel Buffer Assembly from the Receiver. Install Bolt
Assembly into the Barrel Extension Assembly and Barrel Buffer Assembly and install into the Receiver.
38) Raise Bolt Latch and push Bolt Assembly into Receiver.
The Bolt Stud is installed in the Bolt Stud hole on the right side of the Receiver and Bolt Assembly for the M2 and M2A1, and in the left side of the Receiver and Bolt Assembly for the M48
39) Align hole in Bolt Assembly with Bolt Stud hoe in Receiver.
40) M2 and M2A1 only: Install Bolt Stud in Bolt Stud hole in Receiver.
41) Install Drive Spring Rod Assembly in upper right-hand corner of Bolt Assembly. Push forward and to the right until Drive Spring Rod Assembly engages in hole in side plate of Receiver and not in the groove fore the Backplate.
42) Install Backplate Assembly in grooves of Receiver. Pull Backplate Latch Lock while lifting up on
Backplate Latch. Lower Backplate Assembly down until engaged in Receiver.
43) Pull Backplate Latch Lock back and pull up on Backplate Assembly to ensure proper locking.
44) Lift Backplate up and pull up Backplate Assembly to ensure proper locking.
45) Install Cover Assembly on Receiver and latch front to secure.
46) Reopen Cover Assembly. Retract Bolt Assembly far enough for Barrel Locking Spring Lug to center in
Barrel Locking Spring hole on the right-hand side of Receiver.
WARNING
Headspace and timing MUST be checked and adjusted before firing machine gun, after assembling machine gun, and after removing/replacing the barrel. Failure to comply can result in injury or death to personnel, and machine gun damage.
47) M2A1 only: Insert Barrel Assembly into Barrel Support until Barrel Alignment Pin engages Camming
Slot. Rotate Barrel Assembly clockwise and secure Barrel Alignment Pin in Retention.
48) M2 and M48 only: Install and screw Barrel Assembly completely into receiver. Unscrew Barrell
Assembly until completely into two clicks headspace and timing in accordance with TM 9-1005-213-10
49) Ensuring weapon is in single- shot mode, load five or more linked dummy. Close cover assembly and hand-operate MG to ensure all components are function properly. Machine gun should function through a complete cycle in single-shot mode and automatic, perform functions check.
50) Place weapon in automatic mode and repeat previous step.
51) Return weapon to single- shot mode.
SLIDE 11 OFF:
Check on Learning: SLIDE 12 ON:
SLIDE 12 OFF:
Conduct a Review/Summary of the information presented in
TLO - LSA 6. Learning Step / Activity TLO - LSA 6. Perform Function Check on the M2A1 Machine Gun.
Instr Type (I:S Ratio): Military - ICH (1:10)*
Time of Instruction: 25 mins Media Type: Actual Equipment
Other Media: Unassigned Security Classification: This course/lesson will present information that has a Security
SLIDE 13 ON:
INSTRUCTOR NOTE: Refer students to TM 9-1005-347-10, WP 0007-12/13.
1) Move the trigger block to the S (SAFE) position.
2) Move the bolt latch release lock to the unlocked position.
3) Pull back on the retracting slide handle and lock the bolt to the rear. The bolt should lock to the rear.
4) Hold the retracting slide handle, press the bolt latch release, and ride the bolt forward.
5) Press down on the trigger. Weapons should not fire.
6) Move the trigger block to F (FIRE) position.
7) Press down on the trigger. Weapon should fire.
8) Move the blot latch release lock to the locked position.
9) Pull the retracting slide handle to the rear and hold the retracting slide handle to the rear. The bolt should not lock to the rear.
10) Release the pressure on the retracting slide handle and ease the bolt forward.
11) Depress trigger. Weapon should fire.
SLIDE 13 OFF:
Check on Learning: SLIDE 14 ON:
SLIDE 14 OFF:
Conduct a Review/Summary of the information presented in
TLO - LSA 7. Learning Step / Activity TLO - LSA 7. Perform Fixed Headspace and Timing Verification.
Instr Type (I:S Ratio): Military - ICH (1:10)*
Time of Instruction: 30 mins Media Type: Actual Equipment
Other Media: Unassigned Security Classification: This course/lesson will present information that has a Security
SLIDE 15 ON:
INSTRUCTOR NOTE: Refer students to TM 9-1005-347-23&P, WP 0012-1.
WARNING
Failure to properly clear the M2A1 Machine Gun (MG) can result in an accidental discharge of a round.
Ensure to clear weapon disassembling, cleaning, inspecting, transporting or storing. Cleaning consists of unloading the MG and visually inspecting weapon and chamber to ensure all rounds have been removed.
DO NOT release the bolt or press the trigger.
Ensure field maintenance has performed headspace and timing check and adjustment for the M2A1.
DO NOT keep living ammunition in work area.
Failure to comply can result in death or injury to personnel.
Improper headspace and timing can cause the weapon to malfunction, resulting in injury to personnel and damage to equipment. The following guidelines should be strictly enforce to prevent improper headspace and timing issues:
Headspace and timing must be verified by unit armorer prior to issuing. M2A1 headspace and timing adjustment is performed at field support maintenance.
All M2A1 Machime Guns must be inspected and gauged at least once annually for safety and serviceability.
DO NOT insert any object such as coin or feeler gauge between the barrel extension and trunnion block while retracting the bolt to adjust headspace. Placing an object between the barrel extension and trunnion can cause excessive headspace adjustment and possible injury to personnel or damage to weapon.
All Army Reserve and National Guard M2A1 MGs must be inspected and gauged at least once every two years, after the initial/gauging procedures have been accomplished. This two- year interval may be maintained unless preventive maintenance checks and services (PMCS) or other physical evidence indicates that and individual unit’s M2A1 machine guns require inspecting/gauging at a more frequent interval. If it is determined that an inspection is necessary for an individual unit, only that unit will be affected.
This will not affect other units in regard to the interval of inspection. Ensure M2A1 headspace and timing check and adjustment has been performed by field maintenance personnel.
As long as the Wear-Limit Gauge indicates the weapons is acceptable, the Barrel can be change and fired as required. Once the weapons accepts the Wear – Limit Gauge, headspace servicing will be required.
M2 Barrels are not interchangeable with M2A1 barrels. Users shall not install or use M2 barrels with an
M2A1 Machine Gun receiver. Failure to comply can result in injury to personnel and damage to weapon.
Failure to proper attach the Barrel Assembly to the Barrel Extension will cause inaccurate headspace and timing which may result in a misfeed of ammunition, failure to fire, failure to cycle, or catastrophic weapon malfunction:
Ensure that during barrel install installation the square on the Barrel Extension is NOT pulled back
PAST the 3/8 in. hole on the right side of the receiver or the Barrel will not be attached to the Barrell
Extension.
Ensure during reassembly that the Bolt and Barrel Extension Assembly serial number match the last four digits of Receiver serial number to prevent losing headspace, which could cause gun malfunction and serious injury.
Maintain thumb pressure on Buffer Accelerator while install barrel buffer assembly and barrel extension assembly into receiver.
Failure to comply can result in serious injury to personnel and damage to weapon.
NOTE
If required, utilized assistant when performing headspace and timing verification
Headspace is the distance between the face of the Bolt and the base of the cartridge case, fully seated in the Chamber. Timing is the adjustment of the gun so that firing takes place when the recoiling parts are in the correct position for firing. Because the cartridge is held by the T-Slot of the Bolt, headspace with the MG is measured as the distance between the rear of the Barrel and the face of the Bolt. This occurs when the recoiling parts are forward and there is positive contact between the Breech Lock recess in the Bolt and the lock in the Barrel Extensions. Periodic calibration checks of the gauge, at least annually, should be made by support personnel.
Initial headspace is set by field maintenance and no adjustment should be required. Headspace increase gradually with firing due to normal component wear. Periodic checks by unit armor are required to ensure that the specific wear limit if 0.212 in. (5.385mm) is not exceeded.
1) Verify Headspace.
NOTE
If the 0.121. in (5.385 mm) wear limit is exceeded, a headspace adjustment must be performed by field maintenance personnel.
Bolt and Barrel Extension ( with Breech Lock) should remain with the original Receiver Assembly. These parts are identified with the last four digits of the Receiver serial number.
The Breech Lock is pinned to prevent removal from the Barrel Extension. The Breech Lock must only be changed by authorized maintenance personnel for headspace adjustment.
a) Charge weapon to ensure that Firing Pin is retracted.
b) Open Cover
c) Remove slack in the Bolt and Barrel Extension by Retracting Slide Handle until the Barrel Extension begins to separate from the Trunnion Block.
CAUTION
DO NOT depress Trigger when headspace gauge is in T-Slot. Failure to comply can damage equipment.
NOTE
Ensure that No-GO gauge does not have any broken, bent, rusted or pitted areas or there forms of mutilation that could affect dimensional tolerances.
d) Attempt to insert the wear limit gauge in T-Slot between face of Bolt and rear of Barrel.
e) Raise Cartridge Extractor and attempt to insert the wear limit gauge in the T-Slot between face of Bolt and rear of Barrel. If gauge enters, refer to WP 0013 to adjust headspace and timing. If gauge does not enter, release Charging Handle, rotate Cartridge Extractor down, allow Bolt to go forward.
f) Headspace verification is complete. Proceed to timing verification.
2) Verify Timing.
a) Grasp retracting Slide Handle and retract Bolt just enough to insert NO FIRE gauge with beveled edge against Barrel, between Barrel Extension and Trunnion. Release Retracting Slide Handle slowly.
b) Ensure weapon safety switch is in the fire mode. Depress trigger; gun should NOT fire. If M2A1 machine Gun does fire, perform timing adjustment.
c) Retract Bolt just enough to remove NO FIRE gauge and insert FIRE with beveled edge against, Barrell between Barrell and Trunnion Block. Release Retracting Handle slowly.
d) Depress Trigger; M2A1 Machine Gun should fire. If M2A1 does not fire, performing adjustment.
SLIDE 15 OFF:
Check on Learning: SLIDE 16 ON:
SLIDE 16 OFF:
Conduct a Review/Summary of the information presented in the Learning Step.
TLO - LSA 8. Learning Step / Activity TLO - LSA 8. Perform Field Maintenance (PMCS) on the M2A1 Machine Gun.
Instr Type (I:S Ratio): Military - ICH (1:10)*
Time of Instruction: 30 mins Media Type: Actual Equipment
Other Media: Unassigned Security Classification: This course/lesson will present information that has a Security
SLIDE 17 ON:
INSTRUCTOR NOTE: Refer students to TM 9-1005-347-23&P, WP 0007 00-1
NOTE: All PMCS checks and services will be completed before operation of the weapon. Inactive weapons, those not used for firing for three months or longer, will have those PMCS tasks listed as quarterly, semiannually, or annually completed as they are due. All PMCS checks and services annotated with an * will be completed annually during gaging unless forwarded for repair.
NOTE: M2A1 unique parts should NEVER be installed on the M2HB weapons. The Barrel Extension
Assembly and Bolt have been serialized to remain together as an assembly with serial number or receiver. If a new Barrel Extension or Bolt is required, servicing the headspace and timing will be necessary. If any part of the Barrel Extension or Bolt is interchanged, headspace and timing must be reset.
NOTE: Do not attempt to remove the Breech Lock from the Barrel Extension. It is not intended for the
Breech Lock to be removed during cleaning. Pinning the Breech Lock insures that the assigned Breech
Lock/Barrel Extension combination is maintained, thus insuring proper Headspace.
INSTRUCTOR NOTE: Instructor can identify additional faults if desired to ensure the students understand identify faults.
a. Verify the administrative information on the DA 2404.
1) Verify the DODAAC is WBAKT0.
2) Verify the organization is HHC, 13th Military Police Battalion.
3) Verify the ADMIN NUM and SERIAL NUMBER of the weapon.
INSTRUCTOR NOTE: Have students enter the serial number of the weapon that they are going to PMCS as the serial number on the DA Form 2404.
4) Verify M2A1 is listed as the EQUIP MODEL.
5) Verify Machine Gun, Caliber .50 is listed as the EQUIP NOUN.
6) Verify Quarterly is listed as the TYPE INSPECTION.
7) Verify the TMs being used.
b. Conduct the Before Interval Preventive Maintenance Checks and Services for Machine Gun M2A1.
NOTE: Ensure BOTH Barrels are checked during PMCS.
1) Barrel Assembly.
a) Check Barrel Locking notch for wear.
b) Check threads for burrs, cracks, or binding
c) Check Barrel Alignment Pin on barrel for cracks.
d) Check Flash Suppressor is tight and checks for cracks.
2) Bore
NOTE: There is a gap which allows for expansion (when the barrel gets got from firing) of the stellite liner.
If Saboted Light Armor Piercing (SLAP) Ammunition is being used, barrel life will be reduced.
a) Check Bore for pits, bulges, metal fouling, and empty cartridge case or rings.
1) Chamber
a) Check Chamber for pits, bulges, metal fouling and rings.
b) Check Barrel Chamber for empty cartridge case.
2) Barrel Support J Slot
a) Check M2A1 Barrel Support J Slot for burrs.
3) Front Right-Hand/Left-Hand Cartridge Stops
NOTE: Cartridge Stop for blank ammo is longer than cartridge stop for live ammo. Ensure Cartridge Stop is changed when firing blank or live ammo. Rear Cartridge Stop will not replace Front Cartridge Stop.
a) Check if Front Cartridge Stop Right Hand Feed/Front Cartridge Stop or Left Hand Feed is broken, tight fitting, incorrectly assembled, or missing
4) Link Stripper
a) Check if Link Stripper is broken, tight fitting, incorrectly assembled, or missing.
5) Rear Cartridge Stops
a) Check if Rear Cartridge Stop RH feed only/ Rear Cartridge Stop Assembly is broken, tight fitting, incorrectly assembled, or missing. Rear Cartridge Stop.
6) Pawl Pin
a) Check for broken or missing Pawl Pin.
7) Top Cover Assembly
a) Check cover Latch and Cover Latch Lever to see if broken or missing. Check that cover closes correctly.
8) Belt Feed Lever
a) Checks Belt Feed Lever for cracks, breaks and bends.
9) Lock Pin
a) Check for missing Lock Pin
10) Bolt
NOTE: Bolt Assembly with minor gouging and/or imperfections in Locking Lugs causing no degradation in performance in acceptable.
a) Check Bolt Surfaces and Cams for burrs or cracks.
b) Verify serial number on Barrel Extension and Bolt match last four numbers of serial number.
11) Bolt Assembly
NOTE: Bolt Assembly with minor gouging and/or imperfections in Bolt Assembly Bottom Slot that matches up with the Breech Lock causing no degradation in performance is acceptable.
a) Check Alternate Feed Area, Cam Grooves and T-slot for burrs or cracks. Check for chipped T-slot.
b) Inspect Bolt Face for pits and/or eroded areas up to maximum 0.062in. long or wide, 0.031in deep in scattered/random patterns, or rings 0.031in deep and 0.062 in.
12) Bolt Body
a) Check Bolt Body or burrs.
b) When assembled, ensure bolt body slides freely.
13) Sear Stop and Pin
a) Check Sear Stop and Pin for bends or breaks.
14) Cartridge Extractor
a) Check Cartridge Extractor and Spring for burrs or breaks.
15) Bolt Switch
CAUTION: Incorrect installation of Bolt Switch can lead to battered Belt Feed Lever if cover is closed and an attempt is made to function test the weapon.
NOTE: Correct installation of bolt Switch for LH feed is shown in the illustration is shown in the illustration.
a) Check for deformed, broken, or missing Extractor Stop Pin.
16) Extractor Stop Pin
a) Check for deformed, broken or missing Extractor Stop Pin
17) Arm Support
a) Check Bolt Extractor Mounting Arm Support for chips and burrs.
18) Cocking Lever Pin
a) Check Sear Slide for burrs. Ensure Sear notch has a sharp edge and is not chipped or broken.
19) Sear
a) Check Sear for burrs. Ensure Sear notch has a sharp edge and is not chipped or broken.
20) Sear Slide
a) Check Sear Slide movement in guide grooves.
b) Check for distorted Sear Slide notch and proper installation enters from left to right.
21) Barrel Extension
a) Check Barrel Extension for chipping.
b) Check Breech Lock for burrs, cracks, binding or is installed incorrectly.
c) Check beveled edge of Breech Lock for rolled back, broken or chipped edges.
d) Verify serial number on Barrel Extension and Bolt match last four number of serial number on Receiver.
22) Barrel Locking Spring
a) Check Barrel Locking Spring for retention; check Locking Spring for looseness and correct installation
Spring Locking Lug pointed towards Barrel Locking Lug.
b) Check Locking Lug for weakness and/or proper spring action. Check for wear spring locking lug.
23) Barrel Extension Assembly
a) Check for chipped or cracked metal. Check shaft for cracks or looseness.
b) Check first thread for chipped or cracked metal. Chips or cracks may be removing by hand stoning provided chip or crack does not visibly extend beyond the root of the thread.
c) Check last thread for chipped or cracked metal. Chips or cracks may be removed by hand stoning, provided chip or crack does not visibly extend beyond the root of the thread.
d) Check remaining threads in the Barrel Extension for chips or cracks. Chips or crack ½ in. in length or less shall be smoothed or repaired by hand stoning.
24) Trigger Lever
a) Check Trigger Lever for binding, bends cracks, and breaks.
25) Trigger Lever Pin
a) Check for bent or missing Trigger Lever pin and for a broken lock.
26) Drive Spring Rod Assembly
a) Check Drive Spring Rod Assembly for broken or cracked springs, flat spots on coil, or deformed, cracked, or broken rod.
27) Headspace and Timing
WARNING: Improper headspace and timing can cause the weapon to malfunction, resulting in injury to personnel and damage to equipment. Seek medical assistance at once if injury occurs.
a) Unit Armorer will verify headspace and timing.
28) Trigger Lever Stop Assembly
a) Check if Adjustable Stop is broken or as stripped screw threads.
29) Timing Adjustment Nut
a) Check for loose, stripped or missing Timing Adjustment.
30) Timing Lock Screw
a) Ensure Timing Lock Screw is seated into groove of timing adjustment nut and staked in place.
31) Helical Compression Spring
a) Check for burred, bent or missing Shoulder Pin. Check for missing Spring. Check Belt Feed Lever for proper spring action.
32) Belt Feed Lever
a) Check Belt Feed Lever for the correct direction of Feed.
33) Cover Extractor Spring
a) Check Cover Extractor Spring to see if burred or broken.
34) Belt Feed Slide Assembly
a) Check Belt Feed Slide Assembly for burrs, cracks and binding.
35) Belt Feed Pawl
a) Check Belt Feed Pawl for binding in Belt feed Slide Assembly.
36) Spring Pin
a) Check Spring Pin for looseness. Check if Spring Pin wire is broken, coil collapsed or missing.
37) Spring
a) Check for weak, broken, cracked elongated, or collapsed coils or missing Spring.
b) Check Spring for correct installation.
38) Pawl
a) Check for bent or broken Pawl Arm.
39) Pins
a) Check for bent, loose or broken Pins.
40) Flat Spring
a) Check if Flat Spring is weak, broken or not seated properly.
41) Cover Grooves
a) Check Cover Grooves for burrs, cracks or damage.
42) Cover Pin
a) Check for burred, bent, worn or missing Cover Pin.
43) Backplate
a) Check upper and lower Handle Frames for bends, crack or breaks.
44) Buffer Tube
a) Check backplate Buffer Tube for fluids coming from the inside of the Buffer Tube.
45) Buffer Tube Sleeve
a) Check Buffer Tube Sleeve for cracks or missing Bolt Latch Release Lock.
46) Handles
a) Check Handle grips for cracks or missing screws.
47) Bolt Latch Release Lock
a) Check Bolt Latch Release Lock for breaks or failure to hold Bolt Latch Release completely down.
48) Bolt Latch Release
a) Check Bolt Latch Release and Spring for cracks, collapsed Spring, or breaks. Check if Spring, or breaks. Check if Spring is broken or missing. Check for proper spring action by pressing on and releasing
Bolt Latch Release.
49) Trigger and Spring
a) Check Trigger and Spring for cracks, collapsed spring, or breaks. Check if spring is broken or missing.
Check for proper spring action by pressing on and releasing Trigger.
50) Trigger Block
a) Attempt to place Trigger Block in SAFE mode.
51) Retracting Slide Assembly
a) Check Bolt Stud for burrs or breaks.
52) Retracting Slide Handle
a) Check Retracting Slide Handle and Spring for cracks. Check for spring tension and proper assembly.
53) Retracting Slide
a) Check Retracting Slide for burrs and binding in bracket.
54) Cotter Pins
a) Check for missing or broken Cotter Pins.
55) Shoulder pin
a) Check for loose or broken Shoulder Pin, Stud or Shoulder Screw.
56) Nonelectrical Wire
a) Check for broken or missing Nonelectrical Wire.
57) Plunger
a) Check…
This is the start of the file's text. The full file is on GovTribe.
File details come from the government source that posted it. Updated .