101-UAC03C02v_1_0 PERFORM UNIT LEVEL PMCS ON (M4A1).pdf
PDF 312 KB Posted
- Attached to
- Small Arms Maintenance (SAM 31)
- Solicitation number
- W912PB-27-Q-A004
About this file
This document is a CRM (Curriculum Resource Management) Lesson Plan Report for military training, approved and effective as of August 14, 2025. The lesson (101-UAC03C02, Version 1.0) teaches soldiers how to perform Unit Level Preventive Maintenance Checks and Services (PMCS) on the M4A1 carbine rifle to earn MOS 92Y (Small Arms Maintenance). The lesson introduces baseline proficiencies and is designed for soldiers to perform maintenance on the M4A1 in austere environments in accordance with individual task 101-92Y-1043, supporting the Army Learning Area of professional competence and General Learning Outcome 14 regarding technical and tactical competence.
The lesson requires 8 hours of academic resident instruction delivered through discussion, demonstration, and practical exercises, with a 1:10 instructor-to-student ratio for most learning steps. Key instructional topics include demonstrating M4A1 characteristics and components, disassembly procedures (29 sequential steps), inspection for serviceability using PMCS checklists, recording faults on DA Form 2404, cleaning and lubricating with CLP/LSA, reassembly, and performing function checks. Reference materials include TM 9-1005-319-10 and TM 9-1005-319-23&P (technical manuals), DA PAM 750-8 (Army Maintenance Management System), and AR 25-400-2. Students must achieve 100 percent accuracy in sequential order and score a minimum of 80 percent on the examination administered in Lesson 101-92Y10D106. The document includes practical exercise sheets, instructor materials, student handouts, and comprehensive safety and environmental considerations. Distribution is restricted to DOD and DOD contractors due to export control restrictions, and the training product cannot be used to instruct international military students (FD3 foreign disclosure restriction).
View the file
Other files
Show all 14
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
CUI
CRM LESSON PLAN REPORT
PERFORM UNIT LEVEL PMCS ON (M4A1)
101-UAC03C02 / 1.0 ©
Approved 14 Aug 2025
Effective Date: 14 Aug 2025
SCOPE:
This lesson introduces baseline proficiencies to the Soldier trying to earn MOS 92Y, Perform Unit Level PMCS on Small Arms. The expected learning outcomes are that a Soldier will perform Preventive Check Maintenance Service on a M17 pistol. The Soldier will be able to perform this action in an austere environment, in accordance with individual task: 101-92Y-1043 . The lesson supports the Army Learning Area (ALA) of professional competence, and General Learning Outcome (GLO) 14, Soldiers and Civilians are technically and tactically competent. .The goal of this lesson is to provide the Soldier with the knowledge and skills to Perform Unit Level PMCS on Small Arms DA
PAM 750-8, TM 9-1005-470-10, TM 9-1005-470-23&P
Distribution Restriction: Distribution authorized to the DOD and DOD Contractors only due to export control restrictions.This determination was made on 15 June 2014.
Destruction Notice: Destroy by any method that will prevent disclosure of contents or reconstruction of the document Foreign Disclosure: FD3 - This training product has been reviewed by the developers in coordination with the Unit Armor foreign disclosure officer. This training product cannot be used to instruct international military students.
SECTION I. ADMINISTRATIVE DATA
All Course Masters/POIs Including This Lesson
Courses
Course Number
None
POIs
Version Title Phase Status
Task(s) Taught(*) or Supported
Reinforced Task(s)
Knowledge
Skill
Administrative/ Academic Hours
Instructor Action
Test Lesson(s)
Prerequisite Lesson(s)
Training Material Classification
POI Number Version Title Phase Status
Task Number
Individual
Task Title Status
101-92Y-1043 (*) Perform Unit Level PMCS on Small Arms
Approved
Task Number
Task Title
Status
Knowledge Id
Title
Taught
Required
Skill Id
Taught
The administrative/academic (50 min) hours required to teach this lesson are as follows:
Academic
Resident Hours
/ Methods
Yes 4 hrs 10 mins Discussion (Small or Large Group) Yes 2 hrs 30 mins Demonstration Yes 1 hr 10 mins Practical Exercise (Hands-On/Written)
Total Hours(50 min): 8 hrs 0 mins
The instructor action (60 min) hours required to teach this lesson are as follows:
Hours/Actions
0 hrs 10 mins Classroom Setup
Total Hours (60 min): 0 hrs 10 mins
Lesson Number Version
Lesson Title
Lesson Number Version
Lesson Title
Security Level: This course/lesson will present information that has a Security Classification of: U - Unclassified.
Foreign Disclosure Restrictions
References
Student Study Assignment
Requirements
FD3. This training product has been reviewed by the developers in coordination with the Unit Armor foreign disclosure officer. This training product cannot be used to instruct international military students.
Number
Date AR 25-400-2 Army Records Management Program 18 Oct 2022
PAM 750-8 THE ARMY MAINTENANCE MANAGEMENT
SYSTEM (TAMMS) USERS MANUAL
22 Aug 2005
TM 9-1005-470-10 OPERATOR MANUAL FOR MODULAR HANDGUN
SYSTEM (MHS) PISTOL, 9MM, SEMIAUTOMATIC
M17 (NSN 1005-01-661-7317) (EIC 2VN) PISTOL,
9MM, SEMIAUTOMATIC M18 (NSN 1005-01-661-
7323) (EIC 2VP) PISTOL, 9MM, SEMIAUTOMATIC
GO (NSN 1005-01-661-7309) (EIC 2VO)
31 Mar 2019
TM 9-1005-470-23&P MAINTAINER MAINTENANCE MANUAL INCLUDING
REPAIR PARTS AND SPECIAL TOOLS LIST FOR
MODULAR HANDGUN SYSTEM (MHS) PISTOL,
9MM, SEMIAUTOMATIC M17 (EIC 2VN) PISTOL,
9MM, SEMIAUTOMATIC M18 (EIC 2VP) PISTOL,
9MM, SEMIAUTOMATIC GO
30 Jun 2019 none
Instructors must be qualified and certified. Qualification means the faculty member has successfully completed the current TRADOC Center for Teaching and Learning Excellence approved qualification course.
Qualified faculty members can serve as an assistant to a certified instructor/facilitator in order to achieve the technical standard for the course content for which they are assigned.
Certification means the faculty member has completed the qualification requirements, has demonstrated the technical skills and competencies and has been evaluated and certified by a certified faculty member.
Instructor/facilitator candidates must demonstrate proficiency with the specialized content and competencies applicable to the MOS/SL, functional duty/course. After attaining the required technical standard the faculty member should rehearse with a certified instructor/facilitator prior to presenting a lesson or lessons to actual students.
A certified instructor/facilitator must be present to evaluate instructor/facilitator candidates during their initial presentation of each lesson until certified in every lesson for the course. It is the discretion of the certified instructor if the initial presentation was adequate or if more than one evaluation is needed to grant certification.
The certification process must ensure certified instructors display the highest level of competence in instructional techniques, subject matter expertise and the ethics needed to perform their training and education duties and responsibilities to the Army standard.
Support Personnel
Information Technology Support Personnel will provide support.
Additional Support Personnel
Equipment for Instruction
Name Armorer Remarks:
Computer System Analyst Remarks:
ID - Name Student
Student
Ratio Qty
0:0
0:0
Man
Materials
(Note: Asterisk before ID indicates a TADSS.)
Instructor Materials:
1. Lesson plan.
2. Practical Exercise (PE).
3. Practical Exercise Solution.
Ratio Ratio Spt Qty Exp
1005-01-382-0953 - Carbine, 5.56 Millimeter: M4A1 Remarks:
0:0 0:0 No 0 No
1005-01-630-9508 - 30 Round Magazine Assembly Remarks:
0:0 0:0 No 0 No
2540-00-840-9544 - TABLE
TOP,SEAT,PERS
Remarks: One per student, instructor, and visitor area.
1:1 1:1 No 0 No
4240-01-504-0052 -
GOGGLES,INDUSTRIAL
Remarks:
0:0 0:0 No 0 No
5180-00-357-7770 - Tool Kit, Repairman's, Small Arms Remarks:
0:0 0:0 No 0 No
5975-01-099-1035 - Rack, Electronic Equipment Remarks: One per classroom
0:0 0:0 No 1 No
6515-00-612-0000 - Pencil Remarks:
1:1 0:0 No 0 No
6515-01-211-5306 - Paper, Printer, 2- 1/2 Inch Roll Remarks:
0:0 0:0 No 1 No
7021-01-C14-3190 - Computer, Micro Lap-Top Portable AC: M4500 Dell Remarks:
0:0 0:0 No 0 No
7021-01-D01-0269 - PC Tablet, Data Entry: IPAD 2 WIFI 64GB Apple Remarks:
0:0 0:0 No 0 No
7045-01-444-5160 - Disk, CD Recordable, 74 Minutes, 650MB Remarks:
1:1 1:1 No 0 No
7050-01-C14-4309 - Interactive Pen Display: ID422W Smart Remarks:
0:0 0:0 No 0 No
7105-01-470-5332 - Chair, Desk, Lounge with Arms Remarks: One per student, instructor, and visitor area.
1:1 1:1 No 0 No
7490-01-T00-0291 - Card Programmer: RFC-03G Turning Technologies Remarks:
0:0 0:0 No 0 No
7490-01-T00-0292 - Card Programmer: XRC-R02 Turning Technologies
0:0 0:0 No 0 No
Classroom, Training Area, and Range
Ammunition Requirements DODIC - Name Exp
Student
Ratio
Instruct
Ratio
Spt Qty
Instructional Guidance/ Conduct of Lesson
Proponent Lesson Plan Approvals
NOTE: Before presenting this lesson, instructors must thoroughly prepare by studying this lesson and identified reference material.
NOTE: Instructor/Facilitator will ensure to incorporate Army Learning Model and Operational Environment experiences.
ARMY LEARNING MODEL
All instructors/Facilitators will facilitate training under Army Learning Model. Ensuring training is based on quality, relevance and effectiveness of face-to-face learning experiences through outcome-oriented instructional strategies. This type of instruction will foster critical thinking, initiative and operational relevance in context.
OPERATIONAL ENVIRONMENT INTEGRATION
Instructors/Facilitators will facilitate conversations from students and relate this lesson to current Operational Environments (OE) using personal experiences and/or examples obtained from the Center for Army Lessons Learned (CALL). Instructors should provide sufficient OE variables and scenarios to produce the desired Soldier training outcome for this lesson.
NOTE: Verify that the training material is loaded on the computers before beginning the lesson.
Name Rank Position Date michelle.r.brown8.civ Not available Approver 14 Aug 2025
Student Materials:
1. Practical Exercise
2. Pencil/Pen
3. Student Handout
4. Laptop with internet connectivity
5. AR 750-8, TM 9-1005-470-10, TM 9-1005-470-23&P.
ID - Name Quantity Student Ratio
Setup Mins
Cleanup Mins
17135-0 Laboratory Instructional Building, 0 Square Foot
0:0 0 0
SECTION II. INTRODUCTION
Method of Instruction: Discussion (Small or Large Group) Mode of Delivery: Resident Instruction
Instr Type (I:S Ratio): Military - ICH (1:30) Time of Instruction: 15 mins
Motivator
Terminal Learning Objective
Safety
As a unit armorer, it is important that you have a basic understanding on how to conduct preventive maintenance checks and services (PMCS) for small arms plays a vital part of operational readiness. You need to know how to use equipment technical manuals. You need to know, recognize, and understand maintenance forms, what they are, how to use them.
NOTE. Inform the students of the following Terminal Learning Objective requirements.
At the completion of this lesson, you [the student] will:
Action: Perform Unit Level PMCS on M4A1 Conditions:
In a classroom environment, given the requirement to perform field maintenance on the
M4A1 Carbine. Given TM 9-1005-319-10, TM 9-1005-319-23&P, AR 25-400-2, DA Pam
750-8, DA Form 2404, armorer toolkit, safety equipment, cleaner, lubricant and preservative
(CLP/LSA), pen or pencil, and a M4A1 Carbine.
Standards:
Perform unit level preventative maintenance checks and services on small arms in sequential order and with 100% accuracy.
Learning Domain - Level: None assigned
No JPME Learning Areas Supported: None
In a training environment, leaders must perform a risk assessment in accordance with current Risk Management Doctrine. Leaders will complete the current Deliberate Risk Assessment Worksheet in accordance with the TRADOC Safety Officer during the planning and completion of each task and sub-task by assessing mission, enemy, terrain and weather, troops and support available-time available and civil considerations, (METT-TC). Note: During MOPP training, leaders must ensure personnel are monitored for potential heat injury. Local policies and procedures must be followed during times of increased heat category in order to avoid heat related injury. Consider the MOPP work/rest cycles and water replacement guidelines IAW current CBRN doctrine. All operations will be performed to protect and preserve Army personnel and property against accidental loss. Procedures will provide for public safety incidental to Army operations and activities and safe and healthful workplaces, procedures, and equipment. Observe all safety and/or environment precautions regarding electricity, cable, and lines. Provide ventilation for exhaust fumes during equipment operation and use hearing protection when required IAW AR 385-10, the Clean Air Act (CAA) and the CAA amendments, and the OSHA Hazard Communication standard. Accidents are an unacceptable impediment to Army missions, readiness, morale, and resources. Decision makers at every level will employ risk management approaches to effectively preclude unacceptable risk to the safety of personnel and property affiliated with this task. (a) Take personal responsibility. (b) Practice safe operations. (c) Recognize unsafe acts and conditions. (d) Take action to prevent
Risk Assessment Level accidents. (e) Report unsafe acts and conditions. No food or drink is allowed near or around electrical equipment (CPU, file servers, printers, projectors, etc.) due to possible electrical shock or damage to equipment. Exercise care in personal movement in and through such areas. Avoid all electrical cords and associated wiring. In event of electrical storm, you will be instructed to power down equipment.
Low - 1: Fire Hazard.
2. Health Concerns.
3. Weather Hazards.
4. Operate Laptop Computer.
Assessment: 1. Fire, Smoke, limited visibility.
2. Heart Attack or other Medical Condition.
3. Cold Weather, Hot Weather, Tornados, Hail, Sleet, Snow, Rain, Lighting.
4. Liquid Spill, Electrical Hazard.
5. Trip/Falls.
Controls: 1. Emergency Evacuation Plan.
2. Automatic Electronic Defibrillator (AED) and trained personnel, Pre-Accident Plan.
3. Stay indoors and away from windows, wear appropriate clothing for conditions.
4. Liquids not allowed on tables/desks with computers.
5. High Visibility Marking, Briefing.
Leader Actions: 1. Provide Specific Direction to students.
2. Provide current equipment and trained personnel locations.
3. Provide Specific Direction on classroom hazards.
4. Provide Specific Direction on the established evacuation plan.
5. Provide Specific Direction for any emergency situation.1. Provide Specific Direction to students.
2. Provide current equipment and trained personnel locations.
3. Provide Specific Direction on classroom hazards.
4. Provide Specific Direction on the established evacuation plan.
5. Provide Specific Direction for any emergency situation.
Environmental Considerations
Instructional
NOTE: Instructor should conduct a risk assessment to include environmental considerations IAW the current environmental considerations publication, and ensure students are briefed on hazards and control measures.
It is the responsibility of all Soldiers, DA Civilians and Contractors to protect the environment from damage. Environmental protection is not just the law but the right thing to do. It is a continual process and starts with deliberate planning. Always be alert to ways to protect our environment during training and missions. In doing so, you will contribute to the sustainment of our training resources while protecting people and the environment from harmful effects. Refer to ATP 3-34.5 Environmental Considerations and GTA 05-08-002 ENVIRONMENTAL-
RELATED RISK ASSESSMENT.
Lead-in In this lesson, you'll learn to perform unit level PMCS on small arms emphasizing the critical role of creating an audit trail for your unit supply's success.
SECTION III. PRESENTATION
TLO - LSA 1. Learning Step / Activity TLO - LSA 1. Demonstrate knowledge of characteristics capabilities, and features, and Components of the carbine 5.56mm, M4A1
Instr Type (I:S Ratio): Military - ICH (1:10)* (Primary and Assistant Instructor(s): Qualified
Military or Civilian Instructor/Subject Matter Expert (SME); Complete Familiarity with TRADOC Regulation 350-6. Instructors must meet certification requirements in accordance with TRADOC Regulation 350-70; Army Regulation 614-20; QMS Policy #17 Instructor Development Training Plan (IDTP), Course 101-92Y10 CMP, Trained on GCSS-Army Educational Environment.
Time of Instruction: 30 mins Media Type: Unassigned Other Media: Unassigned
Security Classification: This course/lesson will present information that has a Security Classification of: U - Unclassified.
Note: Marked as (*) is derived from the parent learning object
LSA 1- Demonstrate knowledge of characteristics capabilities, and features, and Components of the carbine 5.56mm, M4A1
Instructor Notes: Refer students to TM 9-1005-319-10 WP 0005-1.
CLEARING WEAPON
The weapon MUST be cleared to be considered safe before disassembling, cleaning, inspecting transporting or storing.
If the weapon is not cocked, selector lever should not be pointed toward SAFE.
Ensure weapon is always pointed in a safe direction.
Failure to comply with above warnings may result in injury or death to personnel Seek medical attention if injury occurs.
TM 9-1005-319-10 WP 0005-2 -3
1. Point weapon in safe direction. Place selector lever on SAFE (Figure 1)
2. Remove magazines (Figure 2, Item 2) by pressing magazine catch (Figure 2, Item 1) and pulling the magazine (Figure 2, Item 2) down.
3. Pull the charging handle (Figure 3, Item 1) to the rear.
4. Press and hold the bottom of the bolt catch (Figure 3, Item 3).
5. Allow the bolt to move forward until it engages the bolt catch (Figure 3, Item 3).
6. Return the charging handle (Figure 3, Item 1) to the forward locked position.
7. Ensure that the selector (Figure 3, Item 2) is on SAFE.
8. TM ERROR, step 8 isn't mentioned.
9. Visually inspect the chamber to ensure it contains no ammunition.
10. Allow the bolt to move forward by pressing the upper portion of the bolt catch. (Figure 3, Item 3).
11. Close the ejection port cover.
Instructor Notes: Refer students to TM 9-1005-319-10 WP 0002-1.
Characteristics
M4A1 Carbines are lightweight, gas-operated, air-cooled, magazine-fed, shoulder-fired weapons that fire in semi-automatic, automatic (M16A3/M4A1).
Capabilities
The rifles and carbines provide personnel with an offensive/defensive capability to engage targets with direct small arms fire. The portability and logistical values are greatly increased particularly when air transports are used.
Features
The receivers are made of lightweight aluminum alloys; however, the safety, durability, and function of the rifles /carbines are in no way reduced. The bolt locking action is one of the mechanical features of the rifle/carbine. The bolt assembly and barrel extension contain locking lugs that engage and lock the bolt assembly firmly in the barrel extension. The initial force of the explosion contains locking lugs that engage and lock the bolt assembly firmly in the barrel extension. The initial force explosion of the cartridge is absorbed by the barrel, barrel extension, and bolt assembly. The trigger guard is easily adaptable to winter operations. A spring-loaded retaining pin is depressed to allow ready access to the trigger when wearing artic mittens. The ejection port cover prevents dirt or sand from getting into the ejection port. The ejection port cover must be closed during periods when firing is not anticipated. The ejection port cover opens automatically with the forward or rearward movement of the bolt carrier assembly.
Instructor Note: Refer students to TM 9-1005-319-23&P, 0002-6.
Charging Hand Assembly (Figure 3, item 1) provides initial charging of weapon. Locks forward during sustained fire.
Bolt and Bolt Carrier Assembly (Figure 3, item 2) provides feeding, chambering locking, firing, extracting, and ejecting of cartridges using the buffer spring and projectile propelling gasses for power.
Back up Iron Sight (Figure 3, Item 3) is used to aim weapon if optics are not present or inoperable.
Upper Receiver and Barrel Assembly (Figure 3, Item 4) provides support for bolt carrier assembly. The barrel chambers the cartridge for firing and directs the projectile.
Forward Pistol Grip Assembly (Figure 3, Item 5) is used to increase stability of weapon when firing.
Cartridge Magazine (Figure 3, Item 8) holds 30 cartridges and positions the rounds for feeding
Small Arms Sling (Figure 3, item 7) is used as a means to carry the weapon.
Lower Receiver and Buttstock Assembly (Figure 3, Item 7) assists in basic function of weapon and shoulders the weapon.
Back-up Iron Sight (Figure 3, Item 8) is used to aim weapon if optics are not present or inoperable.
Check on Learning:
Determine if the students have learned the material presented by soliciting student questions and explanations. Ask the students questions and correct any misunderstandings.
Question: Which Major Component of the M4 contains the ejection port and ejection port cover?
Answer: M4 Upper Receiver and Barrel Assembly. (REF: TM 9-1005-319-
10)
Review Summary:
Question: Which assembly on the M4 Carbine provides stripping, chambering, locking, firing, extraction and ejection of cartridges?
Answer: Bolt Carrier Assembly. (REF: TM 9-1005-319-10)
Summary: Take a few minutes to summarize the main topics addressed in this LSA: Review Demonstrate knowledge of Characteristics, Capabilities, Features, and
Major Components of the Carbine 5.56mm, M4A1.
TLO - LSA 2. Learning Step / Activity TLO - LSA 2. Disassemble the M4A1 Carbine
Method of Instruction: Demonstration Mode of Delivery: Resident Instruction
Instr Type (I:S Ratio): Military - ICH (1:10)* (Primary and Assistant Instructor(s): Qualified Military or Civilian Instructor/Subject Matter Expert (SME); Complete Familiarity with TRADOC Regulation 350-6. Instructors must meet certification requirements in accordance with TRADOC Regulation 350-70; Army Regulation 614-20; QMS Policy #17 Instructor Development Training Plan (IDTP), Course 101-92Y10 CMP, Trained on GCSS-Army Educational Environment.
Time of Instruction: 1 hr Media Type: Unassigned
Other Media: Unassigned Security Classification: This course/lesson will present information that has a Security
LSA 2: Disassemble the M4A1 Carbine Rifle.
INSTRUCTOR NOTES: Refer students to TM 9-1005-319-10, pg. 0013-1.
DISASSEMBLY:
1. Unload/clear weapon (WP 0005)
2. Remove sling.
3. Remove handguards or lower adapter rail.
4. Handguards. Place the weapon on the buttstock (Figure 1, Item 3) and press down on the slip ring
(Figure 1, Item 2) with both hands. Using the “buddy system”, have another person pivot the handguards
(Figure 1, Item 1) free.
5. Lower Adapter Rail. Place the weapon on the buttstock (Figure 2, Item 1).
6. Press down on the slip ring (Figure 2, Item 2).
7. Pivot lower rail away (Figure 2, Item 4) from weapon.
8. Pull lower rail (Figure 2, Item 4) back out of the forward handguard cap (Figure 2, Item 3).
9. Push takedown pin (Figure 3, Item 2) left to right as far as it will go.
10. Pivot upper receiver (Figure 3, Item 1) from lower receiver (Figure 3, Item 3)
11. Push receiver pivot pin (Figure 3, Item 4) left to right as far as it will go.
12. Separate upper and lower receivers (Figure 4).
13. Remove carrying handle (Figure 5) if applicable.
14. Loosen the screws (Figure 5, Item 2) on the left side of the clamping bar (Figure 5, Item 3) (DO NOT remove screws completely). The handle (Figure 5, Item 1) will lift off easily once the clamping bar (Figure 5, Item 3) is loose.
15. Pull back charging handle (Figure 6, Item 1) and bolt carrier (Figure 6, Item 2).
16. Remove bolt and bolt carrier assembly (Figure 6, Item 2).
17. Remove charging handle (Figure 6, Item 1).
18. Remove firing pin retaining pin (Figure 7, Item 2).
19. Push in bolt assembly (Figure 7, Item 4) to locked position.
20. Drop firing pin (Figure 7, Item 1) out of rear of bolt carrier (Figure 7, Item 5).
21. Remove bolt cam pin (Figure 7, Item 3) by giving it a ¼ turn and lifting out of the bolt carrier.
22. Remove bolt assembly (Figure 7, Item 4) from carrier (Figure 7, Item 5).
23. Remove extractor pin (Figure 8, Item 1).
24. Remove extractor and spring assembly (Figure 8, Item 3) from bolt (Figure 8, Item 2).
25. Press in buffer (Figure 9, Item 1), depress retainer (Figure 9, Item 2), and release buffer (Figure 9, Item 1).
26. Remove buffer (Figure 10, Item 2) and spring action (Figure 10, Item 1).
27. Carbine. Fully extend buttstock assembly (Figure 11, Item 1).
28. Grasp the lock release lever (Figure 12, Item 4), in the area of the retaining nut (Figure 12, Item 3).
29. Pull downward and slide buttstock (Figure 12, Item 1) rearward to separate the buttstock assembly
(Figure 12, Item 1) from the lower receiver extension (Figure 12, item 2).
Check on Learning:
Q: How many processes are there in the M4A1 disassembly? A: 29
REF: TM 9-1005-319-10, pg. 0014-1.
Q: What is the twelfth step in the M4A1 disassembly process? A: Separate upper and lower receiver (Figure 4).
REF: TM 9-1005-319-10, pg. 0014-4
Review Summary: Take a few minutes to summarize the main topics addressed in this LSA: Disassembly of the M41 Carbine.
TLO - LSA 3. Learning Step / Activity TLO - LSA 3. Inspect the M4A1 Carbine for serviceability
Mode of Delivery: Resident Instruction
Instr Type (I:S Ratio): Military - ICH (1:10)* (Primary and Assistant Instructor(s): Qualified Military or Civilian Instructor/Subject Matter Expert (SME); Complete Familiarity with TRADOC Regulation 350-6. Instructors must meet certification requirements in accordance with TRADOC Regulation 350-70; Army Regulation 614-20; QMS Policy #17 Instructor Development Training Plan (IDTP), Course 101-92Y10 CMP, Trained on GCSS-Army Educational Environment.
Time of Instruction: 1 hr Media Type: Unassigned
Other Media: Unassigned Security Classification: This course/lesson will present information that has a Security
INSTRUCTOR NOTES: Refer students to TM 9-1005-319-10, chapter 4 (PMCS). Briefly define PMCS
(Preventive Maintenance Check Services) to students and before and after PMCS.
PMCS: PMCS is the care, servicing, inspection, detection, and correction of minor faults before these faults cause serious damage, failure, or injury.
Operator Requirements:
1. Perform PMCS each time M4A1 is used.
2. Perform PMCS in order.
3. Perform BEFORE PMCS just before shooting M4A1
4. Perform AFTER PMCS right after shooting M4A1.
5. Attention should be paid to WARNINGS, CAUTIONS, and NOTES.
6. Use DA Form 2404/DA Form 5988-E, Equipment Inspection and Maintenance Worksheet, to record any faults that are discovered before, during, or after use unless you can perform repair. DO NOT record faults you fix.
<Graphic=x>
<Graphic=x><Graphic=x>
SLIDE 12 OFF:
SLIDE 13 ON:
Explanation of column entries.
Item No. Column
Numbers in this column are for reference only. When completing DA Form 2404 (Equipment Inspection and
Maintenance Record) and/or DA Form 5988-E (Equipment Inspection and Maintenance Record) do PMCS for the intervals listed in the sequence described in accordance with DA PAM 750-8 Army Maintenance
Management System (TAAMS) User’s Manual.
Interval Column
This column lists the designated interval for performing the procedure on the item. Be sure to complete the appropriate maintenance forms whenever a check, test, or service is performed. There are three intervals list: Before, During, and After operation of the M4A1 Carbines.
Item to be checked or serviced column
This column provides the location list the items to be checked or serviced.
Procedure column
This column gives the procedure used to check or service the item listed in the item to be checked or serviced column to know if the equipment is ready or available for its intended mission or the operation. The procedure must be done at the time stated in the interval column. No scheduled maintenance is required by dedicated maintenance levels maintainers.
Not Mission Capable (NMC) if: column
Information in this column describes what faults will keep the equipment from being capable of performing its primary mission. If applicable, following Not Mission Capable (NMC) if: condition is suggested remedy that will correct the discovered discrepancy. Follow Standard Operation Procedures (SOP) for maintaining the equipment or reporting equipment failure. Report any malfunctions or failures on DA Form 2404/DA Form
5988-E (Equipment Inspection and Maintenance Worksheet) or refer to DA PAM 750-8, The army
Maintenance Management System (TAMMS) Users Manual.
INSTRUCTOR NOTES: Refer students to table 1, PMCS for modular handgun system (MHS). Before & after
PMCS.
Q: How many days of inactivity of weapons should you do a PMCS?
A:90
REF: TM 9-1005-319-10 0013-1.
Q: How many items are checked or serviced in the before PMCS process of the M4A1 Carbine?
A: 7
REF: TM 9-1005-319-10.
Take a few minutes to summarize the main topics addressed in this LSA:
Inspect the M4A1 Carbine for serviceability.
TLO - LSA 4. Learning Step / Activity TLO - LSA 4. Record faults on a DA Form 2404
Method of Instruction: Discussion (Small or Large Group) Mode of Delivery: Resident Instruction
Instr Type (I:S Ratio): Military - ICH (1:10)* (Primary and Assistant Instructor(s): Qualified Military or Civilian Instructor/Subject Matter Expert (SME); Complete Familiarity with TRADOC Regulation 350-6. Instructors must meet certification requirements in accordance with TRADOC Regulation 350-70; Army Regulation 614-20; QMS Policy #17 Instructor Development Training Plan (IDTP), Course 101-92Y10 CMP, Trained on GCSS-Army Educational Environment.
Time of Instruction: 1 hr Media Type: Unassigned
Other Media: Unassigned Security Classification: This course/lesson will present information that has a Security
INSTRUCTOR NOTE: Refer Students to DA PAM 750-8, para 3-10.
DA Form 2404 (Equipment Inspection and Maintenance Worksheet) have four major purposes. These forms are the central record for-
1) Faults found during an inspection. These faults include PMCS, maintenance activity inspections, diagnostic checks, and spot checks, except as noted.
2) Actions taken during unit/organizational level services for quality control.
3) Faults and repairs required for estimated cost of damage (ECOD) reports.
4) Battlefield damage assessment and repair (BDAR) performed.
INSTRUCTOR NOTE: Refer students to DA Pam 750-8, Figure 3-26. Have students complete the header information as it is explained.
1) Prepare a DA Form 2404.
a) 1. ORGANIZATION. Enter the name of the unit to which the equipment belongs. Enter [HHC 13th Military Police Battalion] in block 1, Organization.
b) 2. NOMENCLATURE AND MODEL.
Enter the noun abbreviation and the model of the equipment. Enter [CARBINE, 5.56 MM, M4A1] in block 2, Nomenclature and Model Number.
c) 3. REGISTRATION/SERIAL/NSN. Leave blank.
(1) Enter the serial or registration number. Enter the NSN when no serial number or registration number is available.
(2) For more than one item, leave blank.
d) 4a MILES. When a deficiency or a shortcoming is found or a service is performed, enter the miles or kilometers on the equipment's odometer.
Leave blank.
e) 4b HOURS. Leave blank.
(1) When a deficiency or a shortcoming is found or a service is performed, enter the hour meter reading.
(2) Leave blank if hours do not apply to the equipment of if no faults are found.
f) 4c ROUNDS FIRED. Leave blank.
g) 4d HOT STARTS Leave blank.
h) 5. DATE. Enter the calendar date the service is performed or the shortcoming was found. Enter [11 Jul XX] in block 5, Date.
i) 6. TYPE OF INSPECTION.
(1) Enter the type of inspection or service to be done (lubrication, monthly, quarterly, semiannual, and so on).
(2) When doing more than one inspection or service at the same time, enter the service symbols in block 6
(for example, L/S).
(3) Enter [Quarterly] in block 6 Type Inspection.
j) 7. TM NUMBER, TM DATE.
(1) Enter the number and date of the PMCS TM. When two TMs cover an item, enter the second TM number and date in the second TM number and date block.
(2) When the manual has changed, print W/C and the latest change number after the TM number. Then, enter the latest change date in TM date block.
(3) Enter [TM 9-1005-319-23&P] and [30 June 2019] in block 7, Technical Manual that applies to the piece of equipment.
k) 8a. SIGNATURE (Person(s) performing inspection. Personnel performing service
/inspection signs and enters rank after inspection is completed.
l) 8b. TIME. Leave blank or use as needed locally
m) 9a SIGNATURE (Maintenance Supervisor). The maintenance supervisor or the commander's designated representative signs and enters rank after service/inspection is completed.
n) 9b. TIME. Leave blank or use as needed locally. for missile or missile subsystem items reported under AR 700-138, chapter 4, enter the time when item was found to be NMC.
o) 10. MANHOURS REQUIRED. Leave blank or use as needed locally.
p) TM ITEM NO a.
(1) Enter the PMCS item number that applies to the fault listed in column c. If the PMCS has no item numbers, list the page, paragraph, or sequence number. Circle the number if the fault is listed in the
Equipment not ready/available column or Not Mission Capable column of the PMCS. If the PMCS has no ready/available or NMC column, circle the TM item number, page, or paragraph number of any fault that makes the equipment NMC.
(2) Pubs or TM sections other than PMCS may be required for safety faults or local dispatching. For example, AR 385-5 lists safety checks that may not be in the PMCS. Those faults are not counted as NMC for DA Form 2406 unless they are listed in the PMCS not ready column or the NMC column. However, list them if a problem with one of them is found.
(3) For those faults not covered by the PMCS, leave this column blank.
q) STATUS b. Enter the status symbol that applies to the fault or deficiency.
r) DEFICIENCIES AND SHORTCOMINGS c.
(1) When using one DA Form 2404 for more than one item of equipment, enter the serial or administration number for the item with the fault. Write the fault on the line below the serial or administration number.
(2) If a fault that can be repaired is found, stop the PMCS and correct the fault. do not enter faults on the
DA Form 2404 that have been repaired. Continue the PMCS to ensure that no other faults exist.
(3) Briefly describe uncorrected faults.
(4) If any items require support maintenance, a separate DA Form 2404 is completed and attached to a DA
Form 2407.
s) CORRECTIVE ACTION d.
(1) Explain corrective action taken.
(2) If parts are needed, the PLL clerk orders them and enters the document number.
(3) Faults that need support maintenance go on a DA Form
2407. Print DA Form 2407 (SPT) in column d.
(4) The commander's designated representative decides what maintenance can be delayed. Faults that do not affect the operation of the equipment and the operator's safety can be deferred.
t) INITIAL WHEN CORRECTED. The person making the corrective action or transferring the information initials other entries. The initials go on the last line of the entry. For quality control, the inspector or commander's representative checks all corrected status symbol X faults to ensure proper repairs have been completed. If properly repaired, the inspector of the commander's designated representative initials the status symbol.
NOTE: Remind the students, if the pistol has not been used for 90 days, perform PMCS in the operator’s manual, refer to TM 9-1005-470-10. If rust is present, the PMCS will be done immediately.
Instructor Notes: Review DA Form 2404 located in DA Pam 750-8, Figure 3-25 (fault noted)
Use of status symbols.
Status symbols are used on automated and manual forms and records to show the seriousness of equipment faults or problems. The five status symbols used are X, Circled X, Horizontal Dash (-), diagonal
Slash (/), and Last Name Initial.
1) X. An X status symbol is for a fault or equipment condition that is a deficiency. Deficiencies put the equipment in an inoperative status. No one authorizes or orders equipment operated until the X condition is repaired or status is changed. If the condition is unusual and could occur on other similar equipment, check the other equipment. The commander or the commander’s designated representative then immediately places all similar equipment in an X status. An X status symbol applies to the following situations.
a) Deficiency on the equipment. The motor officer, maintenance officer, or designated representative inspects all work taken to correct each status symbol X deficiency.
b) Component or assembly. Defective or removed that makes the equipment unsafe to operate.
c) Equipment deficiency listed in the not mission capable if column (formerly equipment not ready/available
if) of the equipment technical manuals (TMs) (preventive maintenance checks and services) (PMCS) table.
d) Fault that endangers the lives of the operator or crew, listed in AR 385-55 as not mission capable (NMC), or that would further damage the equipment.
e) Emergency MWO published but not applied to the equipment: (1) Safety-of-use message issued stating a potentially dangerous or unsafe condition exists on the equipment. (2) Equipment judged by the commander as not able to do its mission.
2) CIRCLED X. A CIRCLED X means the equipment has a deficiency but may be operated under set limitations. The commander or the commander’s designated representative may authorize limited operation.
The limited operation is usually for a one-time only operation but is dependent on the mission. A CIRCLED X status symbol applies to the following situations: a) Urgent MWO or deficiency with limiting conditions on equipment. Limited condition means the equipment can be operated, but only within limits set by the MWO or other publication. The, limits may affect operation or require a maintenance action in a set time. b)
Potentially dangerous condition that requires limiting operations. When this type of condition is found, other similar equipment should also be limited. The commander or the commander’s designated representative puts all similar equipment under limited operations.
3) HORIZONTAL DASH (-). A HORIZONTAL DASH shows that an inspection, service or routine MWO is due.
4) DIAGONAL SLASH (/). A DIAGONAL SLASH shows a fault with equipment other than a deficiency.
Faults must be fixed to make the equipment fully usable and to prevent more problems.
5) LAST NAME INITIAL. The last name initial shows completely satisfactory condition or a corrected fault.
6) Status symbols reflect the judgment. The status symbol reflects the judgment of the person making the inspection, operating the equipment, or doing the maintenance. No one orders an individual to change a status symbol. All changes become permanent, except CIRCLED X, until the fault is corrected or determined otherwise by the commander’s designated representative, who is knowledgeable in maintenance. The faults are corrected per the Army -10 and -20 PMCS maintenance standards as noted in AR 750-1. A status symbol is changed only under the following conditions:
a) Status symbol change. The commander or commander’s designated representative ensures that the following is accomplished if there is a disagreement with a status symbol.
(1) Changes can be made from a less serious to a more serious status symbol, and from a serious to a less serious status symbol.
(2) The commander or commander’s designated representative shows a status symbol change on a DA
Form 5988-E/DA Form 2404 by reentering the fault and new status symbol on the next open line. Status symbol change is written in column D next to the fault.
(3) When either the original or final (change) status symbol is an X or CIRCLED X, the repair work is inspected. When the repair is finished, whoever performed the work initials in column E. The commander or commander’s designated representative designates a qualified person who did not perform the work; this designated inspector puts a last name initial over the status symbol to accept the work and start the process to close out the fault.
Q: What form is used for recording faults?
A: DA Form 2404.
REF: DA Form 750-8 and TM 9-1005-319-23&P.
Q: What is NMC?
A: Non-Mission Capable.
REF: DA Form 750-8.
Review record faults on DA form 2404.
TLO - LSA 5. Learning Step / Activity TLO - LSA 5. Inspect for cleanliness.
Instr Type (I:S Ratio): Military - ICH (1:10)* (Primary and Assistant Instructor(s): Qualified
Military or Civilian Instructor/Subject Matter Expert (SME); Complete Familiarity with TRADOC Regulation 350-6. Instructors must meet certification requirements in accordance with TRADOC Regulation 350-70; Army Regulation 614-20; QMS Policy #17 Instructor Development Training Plan (IDTP), Course 101-92Y10 CMP, Trained on GCSS-Army Educational Environment.
Time of Instruction: 1 hr Media Type: Unassigned
Other Media: Unassigned Security Classification: This course/lesson will present information that has a Security
Instructor Notes: Refer students to TM 9-1005-319-23&P. Go to page 0015-1 and 00-13-6 for cleaning instructions.
Warning: Always clear weapon before cleaning. Ensure weapon is pointed in a safe direction. Failure to comply may result in death or injury personnel. Seek immediate medical attention if injury occurs. Caution:
Do not mix parts of one weapon with other weapons. Parts are not interchangeable. Do not use hot water, or other solvents, or lubricant that has been building up as a result of using CLP will be washed away. Failure to comply with above cautions may result in damage to equipment.
Bore
1. Disassemble weapon (WP 0014).
2. Attach three cleaning rods (Figure 2, Item 1) sections together.
3. Swap out the bore with a patch moistened with CLP or rifle bore cleaner (RBC).
4. Attach the bore brush (Figure 3, Item 1) to the cleaning rods.
5. Point muzzle (Figure 3, Item 4) down.
6. Hold the upper receiver (Figure 3, Item 3) in one hand while inserting the end of the rod (Figure 3, Item 5) without the brush (Figure 3, Item 1) into the chamber (Figure 3, Item 5).
7. Let the rod fall (Figure 3, Item 2) straight through the bore. Approximately 2-3 inches will be sticking out of the muzzle (Figure 3, Item 4) at this point.
8. Attach the handle section (Figure 4, Item 2) of the cleaning rod to the end of the rod (Figure 4, Item
3) sticking out of the muzzle (Figure 4, Item 1).
9. Pull the brush through the bore and out the muzzle (Figure 4, Item 1).
10. After one pull, take off the handle section (Figure 4, Item 2) and repeat steps 5 through 10.
11. Send a patch through the bore after three pulls of the bore brush through the barrel to help clean out the dirt that the brush is getting loose.
12. Replace the bore brush with the rod tip patch holder and a wet patch.
13. Drop the cleaning rod with patch holder and wet patch through the bore.
Upper Receiver
1. Connect chamber brush (Figure 5, Item 3) to cleaning rod handle (Figure 4, Item 1).
2. Coat chamber brush (Figure 5, Item 3) in CLP and insert in chamber and locking lugs (Figure 5, Item
2).
3. Push and twist the chamber brush to clean.
4. Use a worn out bore brush (Figure 6, Item 3) to clean outside of gas tube (Figure 6, Item 2).
5. Wipe down and clean entire upper receiver (Figure 6, Item 1).
Bolt and Bolt Carrier Assembly
1. Clean carbon and oil from firing pin (Figure 7, Item 7)
2. Clean inside bolt carrier key (Figure 7, Item 6) with worn bore brush.
3. Clean firing pin recess (Figure 7, Item 1) with pipe cleaner.
4. Clean firing pin hole (Figure 7, Item 4) with pipe cleaner.
5. Clean behind bolt rings (Figure, Item 2) and lip extractor (Figure 7, Item 5).
6. Clean carbon deposits and dirt from locking lugs (Figure 7, Item 3).
Lower Receiver and Buttstock Assembly
1. Wipe dirt from trigger (Figure 8, Item 5) with a swab.
2. Use a swab dampened with CLP to clean powder fouling, corrosion, and dirt from outside parts of lower receiver and extension assembly (Figure 8, Item 4).
3. Use pipe cleaner to clean buttstock drain hole (Figure 8, Item 3).
4. Clean buffer assembly (Figure 8, Item 2), spring, (Figure 8, Item 1) and inside receiver extension
(Figure 8, Item 6) with swab dampened with CLP.
5. Wipe the exterior of lower receiver and extension assembly (Figure 8, Item 4).
Ejector
1. Place three drops of CLP on the ejector (Figure 9, Item 1).
2. Press down against the ejector (Figure 9, Item 1). Ejector is spring loaded; some resistance will be felt.
3. Ease off and press down again repeat several times. Add CLP as needed. Once spring action of ejector (Figure 9, Item 1) is smooth and strong, dry excess CLP off bolt (Figure 9, Item 2).
4. Dry off excess CLP when process is completed.
Cleaning Adapter Rails and Covers
1. Remove rail covers (Figure 10, Item 1).
2. Use a general-purpose brush (Figure 10, Item 4) from the standard cleaning kit to clean the adapter rails (Figure 10, Item 3) and rail covers (Figure 10, Item 1).
3. Lightly lubricate the upper and lower rail assemblies (Figure 10, Item 3) and retaining clips (Figure 10, Item 2) in the rail covers (Figure 10, Item 1).
4. Remove the lower rail assembly (Figure 11, Item 2) when debris is present and thoroughly clean the thermal liner (Figure 11, Item 3) to maintain heat reflective surface.
5. When exposed to salt water or corrosive materials, rinse the upper and lower rail assemblies (Figure
11, Item 1 and Item 2) in fresh water as soon as tactically possible.
6. Thoroughly clean, inspect, and lubricate the upper and lower rail assemblies as required.
Check on Learning:
Q: What are the 6 items that will be cleaned on a M4A1 Carbine?
A: Bore, Upper Receiver, Bolt and Bolt Carrier Assembly, Lower Receiver and Buttstock Assembly, Ejector, and Adapter Rails and Covers.
REF: TM 9-1005-319-10, pg. 0015-4 to 0015-13.
Q: Ejector is , ;
some resistance will
A: spring, loaded.
be felt.
REF: TM 9-1005-319-10, pg. 0015-11.
Review inspect for cleanliness.
TLO - LSA 6. Learning Step / Activity TLO - LSA 6. Lubricate with CLP.
Instr Type (I:S Ratio): Military - ICH (1:10)* (Primary and Assistant Instructor(s): Qualified
Military or Civilian Instructor/Subject Matter Expert (SME); Complete Familiarity with TRADOC Regulation 350-6. Instructors must meet certification requirements in accordance with TRADOC Regulation 350-70; Army Regulation 614-20; QMS Policy #17 Instructor Development Training Plan (IDTP), Course 101-92Y10 CMP, Trained on GCSS-Army Educational Environment.
Time of Instruction: 30 mins Media Type: Unassigned Other Media: Unassigned
Security Classification: This course/lesson will present information that has a Security
LSA 6 – Lubricate with CLP.
INSTRUCTOR NOTES: Refer students to TM 9-1005-470-10, WP 0013-10 and 11. Have weapons available for demonstration.
Lubrication (WP 0013)
Caution: Do not mix lubricants on weapon. Thoroughly clean the weapon when changing from one cleaner/lubricant to another. Failure to comply may result in malfunction or damage to equipment.
NOTE: CLP, LSA, and LAW are the only lubricants authorized for MHS. Under all but the coldest arctic conditions, CLP is the cleaner/lubricant to use on pistol. Use LAW at temperatures below -10 degrees
Fahrenheit (-23 degree Celsius). Always shake container well before use. Apply using a clean rag or swab.
Lightly lubricated means lubricant is a film barely visible to the eye. Generously lubricated means lubricant is thick enough to spread with finger.
1. Barrel. Lightly lubricate exterior surfaces of barrel.
2. Slide Assembly
Caution: Do not lubricate striker or allow lubricant to flow into striker. Failure to comply may result in damage to equipment.
a. Lightly lubricate rails on both sides of slide.
b. Lightly lubricate bushing surface of slide.
3. Recoils Spring Guide Assembly.
Lightly lubricate recoil spring and spring guide.
4. Receiver/Grip Module Assembly
Lubricate four receiver rails with one drop of lubricant per rail.
SLIDE 23 OFF:
SLIDE 24 ON:
Q: What are the only lubricate authorized for the Modular Handgun
System?
A: CLP, LSA, and LAW are the only lubricants authorized for MHS.
REF: TM 9-1005-470-10, WP 0013-10.
Q: What is needed when you change from one lubricant with another lubricant?
A: Clean weapon thoroughly.
REF: TM 9-1005-470-10, WP 0013-10.
SLIDE 24 OFF:
SLIDE 25 ON:
Lubricate with CLP.
SLIDE 25 OFF:
SLIDE 26 ON:
TLO - LSA 7. Learning Step / Activity TLO - LSA 7. Assemble the M4A1
Instr Type (I:S Ratio): Military - ICH (1:10)* (Primary and Assistant Instructor(s): Qualified
Military or Civilian Instructor/Subject Matter Expert (SME); Complete Familiarity with TRADOC Regulation 350-6. Instructors must meet certification requirements in accordance with TRADOC Regulation 350-70; Army Regulation 614-20; QMS Policy #17 Instructor Development Training Plan (IDTP), Course 101-92Y10 CMP, Trained on GCSS-Army Educational Environment.
Time of Instruction: 30 mins Media Type: Unassigned Other Media: Unassigned
Security Classification: This course/lesson will present information that has a Security
INSTRUCTOR NOTE: Refer students to TM 9-1005-319-10, WP 0018-1-15. Have weapons available for demonstration.
Extractor Assembly (WP 0018-1)
a. Ensure extractor spring (Figure 1, Item 1) is installed in the extractor (Figure 1, Item 2).
b. Insert extractor assembly (Figure 2, Item 3) into bolt (Figure 2, Item 2).
c. Install extractor pin (Figure 2, Item 1).
Bolt Carrier Assembly (WP 0018-2)
Caution: Do not switch bolts between weapons. Ensure that the bolt ring gaps are staggered (approximately
1/3 turn apart). Failure to do so will cause cycling and recoil problems. Failure to comply with above cautions may result in damage to equipment.
a. Slide bolt (Figure 3, Item 4) into carrier (Figure 3, Item 5).
b. Insert bolt cam pin (Figure 3, Item 3).
c. Turn cam pin (Figure 3, Item 3) a ¼ turn after reassembly.
d. Drop firing pin (Figure 3, Item 1).
e. Seat the firing pin (Figure 3, Item 1).
f. Pull bolt (Figure 3, Item 4) forward.
Note: Firing pin should not fall out when bolt carrier assembly is turned upside down.
g. Insert firing pin retaining pin (Figure 3, Item 2).
h. Insert charging handle (Figure 4, Item 1) part way.
i. Slide bolt carrier assembly (Figure 5, Item 1) into charging handle groove (Figure 5, Item 2).
j. Push charging handle (Figure 6, Item 3) and bolt carrier assembly (Figure 6, Item 1) together into upper receiver (Figure 6, Item 2) until fully seated.
k. Slide the clamping bar (Figure 7, Item 2) against the receiver (Figure 7, Item 3) with the lower edge of the carrying handle underneath the slotted section. Hand tighten round nuts (Figure 7, Item 1).
Reassemble buttstock
a. Grasp the lock release lever (Figure 8, Item 4) in the area of the retaining nut (Figure 8, Item 1) onto the lower receiver extension (Figure 8, Item 2).
b. Insert buffer spring (Figure 9, Item 1) and buffer (Figure 9, Item 2) into lower receiver extension (Figure
9, Item 3).
Join Receivers
a. Join upper (Figure 11, Item 1) and lower receivers (Figure 11, Item 2).
Engage Pivot Pin
a. Engage receiver pivot pin (Figure 12, Item 4).
b. Close upper (Figure 12, Item 1) and lower receiver assemblies (Figure 12, Item 3).
c. Push in takedown pin (Figure 12, Item 2).
Assemble Handguards
a. Place the weapon on the buttstock (Figure 13, Item 3) and press down on the slip ring (Figure 13, Item
4) with both hands. Have another person place the top handguard (Figure, Item 1) and the bottom handguard (Figure 13, Item 2) on the weapon. (Buddy System).
Lower Adapter Rail
a. Insert the front flange of the lower rail (Figure 14, Item 3) under the front handguard cap (Figure 14, Item 2).
b. Pull back on the handguard slip ring (Figure 14, Item 1).
c. Pivot rear flange of adapter rail (Figure 14, Item 3) over the edge of the handguard slip ring (Figure 14, Item 1) and release the slip ring (Figure 13, Item 1). Ensure the handguard slip ring (Figure 14, Item 1) engages completely around the flange.
d. Install Sling (Figure 15, Item 1).
Installation of Adapter Rail Covers
a. Install the right, left, and bottom rail covers (Figure 16, Item 5) from the muzzle end (Figure 16, Item 4) of the adapter rails (Figure 16, Item 3).
b. Ensure all rail covers have the retaining clip (Figure 16, Item 6)…
This is the start of the file's text. The full file is on GovTribe.
File details come from the government source that posted it. Updated .