101-UAC03A00v_01_0 CONTROL WEAPONS AND AMMUNITION IN THE ARMS ROOM.pdf
PDF 344 KB Posted
- Attached to
- Small Arms Maintenance (SAM 31)
- Solicitation number
- W912PB-27-Q-A004
About this file
This is a Curriculum Resource Material (CRM) Lesson Plan Report for Army training on controlling weapons and ammunition in the arms room, effective August 8, 2025. The lesson (101-UAC03A00/01.0) introduces newly designated unit armorers to weapons and ammunition control procedures and is designed to support professional competence and General Learning Outcome 14 for technical and tactical competency. The training is unclassified and restricted to U.S. Government agencies and contractors only; it cannot be used to instruct international military students (FD3 foreign disclosure restriction).
The lesson comprises six learning steps delivered over approximately 12 hours of classroom instruction plus 25 minutes of setup time. Key topics include: controlling physical security procedures for the arms room per AR 190-11, AR 190-13, AR 710-4, and related Army regulations; maintaining proper key control using DA Form 5513; preparing DA Form 3749 equipment receipts; issuing unassigned weapons via DA Forms 3161 and 2062; and performing custody transfers of arms room storage facilities. Required materials include the lesson plan, practical exercises, solutions, Army publications, high-security locks, and secondary padlocks. Students must demonstrate competency by achieving a minimum 80% score on an examination administered during Lesson 101-92Y10D03. The lesson employs discussion, demonstration, and reflective discussion methods and incorporates operational environment experiences and Center for Army Lessons Learned examples. Instructor preparation requires thorough study of referenced Army Regulations and verification that training data is loaded on instructor computers prior to delivery.
View the file
Other files
Show all 14
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
CUI
CRM LESSON PLAN REPORT
CONTROL WEAPONS AND AMMUNITION IN THE ARMS ROOM
101-UAC03A00 / 01.0 ©
Approved 08 Aug 2025
Effective Date: 08 Aug 2025
SCOPE:
This lesson introduces the newly designated unit armorer how to control weapons and ammunition in the arms room. The expected learning outcomes is for the student to be able to control weapons and ammunition in the arms room without losing supply accountability in accordance with AR 190-11, AR 190-13, AR 25-50, AR 25-400-2, AR 710-2, and DA Pamphlet 710-2-1. This lesson supports the Army Learning Area (ALA) of professional competence, and General Learning Outcome (GLO) 14, Soldiers and Civilians are technically and tactically competent. The goal of this lesson is to provide the Student with the knowledge and skills to control weapons and ammunition in the arms room without supervision and to the standards outlined in AR 190-11, AR 190-13, AR 25-50, AR 25-400-2, AR 710-2, and DA Pamphlet 710-2-1.
Distribution Restriction: Distribution authorized to U.S. Government agencies and their contractors only for specific authority and export control. This determination was made on 07 July 2025.
Insert Basement, Picatinny, NJ 07806 Destruction Notice: Destroy by any method that will prevent disclosure of contents or reconstruction of the document Foreign Disclosure: FD3 - This training product has been reviewed by the developers in coordination with the Unit Armor foreign disclosure officer. This training product cannot be used to instruct international military students.
SECTION I. ADMINISTRATIVE DATA
All Course Masters/POIs Including This Lesson
Courses
Course Number
None
POIs
Version Title Phase Status
Task(s) Taught(*) or Supported
Reinforced Task(s)
Knowledge
Skill
Administrative/ Academic Hours
Instructor Action
Test Lesson(s)
Prerequisite Lesson(s)
Training Material Classification
POI Number Version Title Phase Status
Task Number
Task Title
Status
Task Number
Task Title
Status
Knowledge Id
Title
Taught
Required
K0391 Know physical security standards. Yes No
Skill Id
Taught
S0929 Recognizing physical security standards, concept, controls, and systems
Yes No
The administrative/academic (50 min) hours required to teach this lesson are as follows:
Academic Resident Hours / Methods
Yes Yes Yes
3 hrs 0 hrs 8 hrs
5 mins 10 mins 35 mins
Discussion (Small or Large Group) Reflective Discussion Demonstration
Total Hours(50 min): 12 hrs 0 mins
The instructor action (60 min) hours required to teach this lesson are as follows:
Hours/Actions
0 hrs 25 mins Classroom Setup
Total Hours (60 min): 0 hrs 25 mins
Lesson Number Version
Lesson Title
Lesson Number Version
Lesson Title
Security Level: This course/lesson will present information that has a Security Classification of: U - Unclassified.
Foreign Disclosure Restrictions
References
FD3. This training product has been reviewed by the developers in coordination with the Unit Armor foreign disclosure officer. This training product cannot be used to instruct international military students.
Student Study Assignment
Instructor Requirements
Support Personnel
Additional Support Personnel Requirements
None
Primary Instructor and Assistant Instructor(s)
Armorer Computer System Analyst
Student
Man
Equipment for Instruction
Materials Required Instructor Materials:
1. Lesson plan.
2. Practical exercise (PE)
3. Practical exercise solution.
4. Required publications.
5. High security lock.
6. Secondary padlock.
Number
Date
AR 190-11 Physical Security of Arms, Ammunition and Explosives
17 Jan 2019
AR 190-13 The Army Physical Security Program 27 Jun 2019 AR 25-50, C7 Preparing and Managing Correspondence (Change 7
Incorporated 04 OCT 2024) 10 Oct 2020
AR 710-4 Property Accountability 26 Dec 2023 AR 735-5 Relief of Responsibility and Accountability 10 Mar 2024 ARIMS User Guide Army Records Information Management System
(ARIMS) User Guide 04 Aug 2022
Name Ratio Qty Hours
Armorer 0:0 1 1.0 Remarks:
Computer System Analyst 0:0 1 14.0 Remarks:
ID - Name Student Instructor
Ratio Ratio Spt Qty Exp
5340-00-158-3805 - Padlock 1:30 0:0 No 0 No Remarks:
7021-01-C14-3190 - Computer, Micro 0:0 0:0 No 2 No Lap-Top Portable AC: M4500 Dell
Remarks: 1 Computer for Instructor use
1 Computer for monitor's Table
7021-01-D01-0269 - PC Tablet, Data 1:1 0:0 No 1 No Entry: IPAD 2 WIFI 64GB Apple
Remarks:
7490-01-T00-0291 - Card 1:1 0:0 No 0 No Programmer: RFC-03G Turning
Technologies
Remarks:
(Note: Asterisk before ID indicates a TADSS.)
Student Materials:
1. Practical exercise.
2. Student handout.
3. Required publications.
4. Blank sheet of paper.
5. Pen or pencil.
Classroom, Training Area, and Range
Ammunition
Student
Instruct
Spt Requirements DODIC - Name Exp
Ratio Ratio Qty
Instructional Guidance/ Conduct of Lesson NOTE: Before presenting this lesson, instructors must thoroughly prepare by studying this lesson and identified reference material.
NOTE: Instructor/Facilitator will ensure to incorporate OE experiences.
Army Learning Model All instructors/facilitators will facilitate training under the Army Learning Model. Ensuring training is based on quality, relevance and effectiveness of face-to-face learning experiences through outcome-oriented instructional strategies. This type of instruction will foster critical thinking, initiative and operational relevance in context.
OE Integration Instructors/facilitators will facilitate conversations from students and relate this lesson to current operational environments (OE) using personal experiences and/or examples obtained from the Center of Army Lessons Learned (CALL). Instructors/facilitators should provide sufficient OE variables and scenarios to produce the desired soldier training outcome for this lesson.
NOTE: Verify that training data is loaded on the instructor computer and the computer is operational.
Proponent Lesson Plan Approvals Name Rank Position Date michelle.r.brown8.civ Not available Approver 08 Aug 2025
SECTION II. INTRODUCTION
Method of Instruction: Discussion (Small or Large Group) Mode of Delivery: Resident Instruction
Instr Type (I:S Ratio): Military - ICH (1:30) Time of Instruction: 5 mins
Motivator SLIDE 92Y10D01-1 (ON)
The Commander may designate you as the unit armorer. One of the most important duties you will have as the unit armorer is the control of the unit's arms, ammunition, and explosives. This responsibility must be taken very seriously. One could compare arms room security to bank vault security at the bank where your money is deposited. Access to the arms room is very similar except that the stakes are much higher as weapons and ammunition are involved. You must fully understand all of the physical security requirements and administrative procedures involved to properly secure all weapons and ammunition in the arms room without losing accountability.
Introduce the Control Weapons and Ammunition in the Arms Room lesson to the students.
SLIDE 92Y10D01-1 (OFF)
SLIDE 92Y10D01-2 (ON)
INSTRUCTOR NOTE: Review the Terminal Learning Objective with the students.
SLIDE 92Y10D01-2 (OFF)
Terminal Learning Objective
NOTE. Inform the students of the following Terminal Learning Objective requirements.
At the completion of this lesson, you [the student] will:
Action: Control Weapons and Ammunition in the Arms Room Conditions:
In a classroom environment and given the responsibility to control weapons and ammunition in the unit arms room. Given AR 190-11 (Physical Security of Arms, Ammunition, and Explosives), AR 190-13 (The Army Physical Security Program), AR 25-50 (Preparing and Managing Correspondence), AR 25-400-2 (The Army Records Information Management System (ARIMS), AR 710-4 (Using Unit Supply System (Manual Procedures)), Sensitive Item Inventory Listing, DA Form 2062 (Hand Receipt), DA Form 3161 (Request for Issue or Turn-In), DA Form 3749 (Equipment Receipt), Master Authorization List (MAL), DA Form 5513 (Key Control Register and Inventory), arms room, arms room keys, property records, access roster, restricted area signs, weapons/ammunition control log, equipment, local standing operating procedures (SOPs), local forms program, and a computer.
Standards:
Control weapons and ammunition in the arms room without losing supply accountability in accordance with AR 190-11, AR 190-13, AR 25-50, AR
25-400-2, AR 710-4.
Learning Domain - Level: Cognitive - Understanding
No JPME Learning Areas Supported: Supports GLO 10 & 11.
Safety
Risk Assessment Level
General classroom safety and electrical equipment safety procedures will be followed.
Warning: Do not place electrical equipment directly on wet ground, snow or ice for operation.
Electrocution can result if the equipment is operated without proper grounding. Before connecting the equipment to a power source, verify that all switches are in the off position. Equipment uses power line voltage. Serious injury or death may occur on contact. Observe all safety precautions when connecting power cables or performing maintenance.
Low - Tripping Assessment: Caused by loose wires or liquids.
Controls: Ensure wires are properly secured; no food or drink in classroom or near equipment.
Leader Actions: Supervise and ensure guidance is followed by the students.
Environmental Considerations
Instructional Lead-in
NOTE: Instructor should conduct a risk assessment to include environmental considerations IAW the current environmental considerations publication, and ensure students are briefed on hazards and control measures.
NOTE: It is the responsibility of all Soldiers, DA Civilians, and Contractors to protect the environment from damage.
During this lesson you will learn how to maintain a high state of security of the arms, ammunition, and explosives that are entrusted to you in the arms room. The Army's inventory of arms, ammunition, and explosives are a vital part of its readiness posture. Loss or theft of such equipment can foster fear in the public sector and create an image of the Army's inability to properly secure its assets.
SECTION III. PRESENTATION
TLO - LSA 1. Learning Step / Activity TLO - LSA 1. Control physical security procedures for the Arms Room
Method of Instruction: Discussion (Small or Large Group) Mode of Delivery: Resident Instruction
Instr Type (I:S Ratio): Military - ICH (1:15)* Time of Instruction: 3 hrs
Media Type: PowerPoint Presentation Other Media: Unassigned
Security Classification: This course/lesson will present information that has a Security Classification of: U - Unclassified.
Note: Marked as (*) is derived from the parent learning object
SLIDE 3 ON:
LSA 1. Control physical security procedures for the Arms Room
A. Required Regulations governing Arms, Ammunition and Explosives (AA&E) in the arms room.
INSTRUCTOR NOTE: Refer the students to AR 190-11, Para 1-2 and Appendix A.
Explain to the students that there are other regulations that will assist them with guidance on physical security, such as AR 190-13 and AR 710-4. Inform the students that they will visit the model arms room training facility or an arms room facility at the local training area (when available) to gain a better understanding of how an arms room is maintained.
SLIDE 3 OFF:
SLIDE 4 ON:
B. Responsibilities:
INSTRUCTOR NOTE: Refer the students to AR 190-11, Para 8-2(b)-(e)
b. Commanders and custodians of AA&E will—
(1) Submit a Serious Incident Report, if required by AR 190–45.
(2) Provide a report on DA Form 3056 (RCS Just–1010) on incidents meeting criteria in paragraph a, above, within 72 hours.
(3) Provide a report on DA Form 3056 on AA&E in-transit losses or inventory discrepancies, not due to theft within 12 days. If loss is recovered before 12 days, no report is required.
(4) Initiate a report of recovery on DA Form 3056 for AA&E items held as evidence by any local, state, or federal law enforcement agency in the area. Notify the commander having lost the items.
(5) Promptly submit appropriate report to the National Crime Information Center (NCIC) and DOD Central
Registry (see para 8–3, below).
(6) Conduct investigations per AR 15–6, when losses equal or exceed the amounts shown in appendix E of this regulation. AR 15–6 investigations may be conducted for lesser amounts.
(7) Reports will include incidents involving arms and ammunition meeting criteria in paragraph a, above, in the custody of a nonappropriated fund activity (such as an exchange, rod and gun club, or recreational marksmanship activity).
c. The IMCOM and the ARNG will maintain records including, at the very minimum, all instances of thefts, losses, and recoveries of AA&E, including any reported under paragraph a, above.
d. These records will include—
(1) A summary of the circumstances in each instance.
(2) Dates, locations, and units such as Regular Army, ARNG, or USAR.
(3) A statement regarding the loss or recovery based on the investigation, such as inventory, theft, in-transit, training, operational, or other.
e. Prepare a consolidated report on all losses, thefts, recoveries, or inventory adjustment of AA&E for the calendar year. Submit this report to the Headquarters, Department of the Army, Provost Marshal General
(DAPM–MPO–PS), 2800 Army Pentagon, Washington, DC 20310–2800, by 30 January of the following year.
SLIDE 4 OFF:
SLIDE 5 TO 7 ON:
C. Construction of facilities:
INSTRUCTOR NOTE: Go over the construction requirements listed in AR 190-11, Appendix G with the students.
1. The provisions of this regulation are mandatory for construction of new permanent storage structures at land-based installations that store sensitive AA&E. Modification to existing facilities will be accomplished per the criteria set forth in this regulation.
2. Qualified engineer personnel will verify the structure composition of AA&E storage facilities (for example, walls, ceilings, roofs, floors, and doors). Statements will be prepared on a current DA Form 4604
(Security Construction Statement). Existing statements will remain valid but will be transcribed to the current form within 180 days from the date of this regulation. Statements will indicate the highest construction category met for storage of AA&E (for example, Category I, Category II, Category III, or Category IV AA&E items) The DA Form 4604 will be affixed to the interior wall of each AA&E storage facility. A blanket statement on DA Form 4604 may be issued at an installation for all facilities, such as ammunition magazines, constructed according to the same specifications. Under these circumstances, a copy of the DA
Form 4604 need not be affixed to the interior wall of each individual storage structure, but must specifically identify the facilities by number and location and be readily available for inspection. Security construction statements will be reviewed during PS surveys and inspections. The statements will be revalidated by engineer personnel every 5 years.
3. PS personnel will monitor construction of new facilities and renovation of existing facilities. Engineer personnel will coordinate new construction and renovation projects with the local PM or security officer. In addition to meeting construction standards, storage of AA&E will meet PS criteria, such as Intrusion
Detection Systems (IDSs), locks and hasps, lighting, and security patrols, as necessary, for the particular category of AA&E involved.
D. All AA&E deployed in the field for training or operational purposes will be secured at all times.
1. Commanders will establish appropriate security measures to ensure that weapons stored or installed in tanks, vehicles, or aircraft are protected at all times.
SLIDE 5 TO 7 OFF:
SLIDE 8 ON:
INSTRUCTOR NOTE: Refer the students to AR 190-11, Para 2-5
E. Field level munitions storage area (FLMSA) will be designated by the commander and used to temporarily hold unit level munitions in a field environment to meet training requirements.
a) Access to the FLMSA will be strictly controlled.
b) Perimeter barriers, either temporary or permanent, must be in place to preclude unauthorized entry into the storage area.
c) Storage areas will be posted as a restricted area.
d) Armed guards will be posted at the FLMSA to control entry and to protect the AA&E.
SLIDE 8 OFF:
SLIDE 9 ON:
3) When storage in an arms storage room, modular vault or building impedes training or operational requirements, arms may be stored or installed on the vehicle or aircraft to which assigned or in other configurations per AR 190-11 and as specified by the PMG. Weapons stored or installed in tanks, vehicles or aircraft will be protected as part of the overall system in which they are installed or stored.
a) Commanders will establish appropriate security measures to ensure weapons stored or installed in tanks, vehicles or aircraft are protected at all times, particularly when unmanned.
(1) When not in use, tanks, vehicles or aircraft containing weapons will be parked inside a secure motor pool or an aircraft park area.
(2) When operational readiness permits, weapons mounted on tanks, vehicles, or aircraft that are accessible and easily removable will be dismounted and secured inside the locked tank, vehicle, aircraft, or other secure location. Weapons that are dismounted and secured inside the locked tank, vehicle, aircraft, and weapons that remain installed on board will be made inoperative by removal of barrels or other essential firing components. Such components will be secured in a locked metal container inside the tank, vehicle, or aircraft, or other secure location. The container will be secured to the tank, vehicle, aircraft, or other secure structure with bolts or chains equipped with secondary padlocks. Spare barrels may be stored inside a locked, totally enclosed, armored combat vehicle when the other essential firing components are secured in an arms storage room and the vehicle is parked inside a motor park which provides continuous surveillance by guards and Level III security measures per AR 190–51.
(3) Weapon systems that are impractical to dismount, due to operational readiness or damage to the weapon system will be made inoperable by the removal of essential component or components.
4) Large weapons (such as crew served weapons and mortar tubes) that cannot be secured in arms rooms or other arms storage facilities because of inadequate storage space, may be stored in a locked, totally enclosed armored vehicle. In such cases security measures as stated earlier apply.
5) Large weapons that cannot be secured in arms rooms, as stated above, may also be secured in other secure locations, such as a room made secure by compensatory measures. In such cases, protection and surveillance by guard or other personnel will be provided according to the risk category of the weapons involved. Such weapons will be rendered inoperable according to the requirements prescribed in paragraph
4–1a(1)(b).
SLIDE 9 OFF:
SLIDE 10 ON:
F. Inspections and Audits:
INSTRUCTOR NOTE: Refer students to AR 190-11, Para 2-6.
1) The garrison commander will ensure that physical security (PS) inspections are conducted in accordance with AR 190-13 for AA&E governed by AR 190-11.
a. Inspections.
(1) Security Management System (Counter Measures) will be used in accordance with AR 190–13.
(2) Physical security inspections will be conducted at intervals not to exceed 18 months and will include—
(a) Review of facility construction standards in accordance with this regulation.
(b) Review of PS measures and compliance.
(c) Review of current deviations and applied compensatory measures (if any) and the need to continue or cancel the deviation.
(d) AA&E inventory and accountability procedures, to include issue and turn in procedures.
(e) AA&E loss or gain reporting.
(f) Review of suitability and screening of personnel with access to AA&E in accordance with this regulation.(1) For new AA&E storage facilities, and before and immediately after occupancy.
(2) On significant change in facility structure.
(3) After a forced entry or attempted forced entry with or without theft.
(4) When units have received an unsatisfactory rating on PS inspection, re-inspection will be within 6 months. A copy of an unsatisfactory inspection concerning Reserve Component (RC) and Reserve Officers’
Training Corps (ROTC) units will be furnished to the installation commander providing the logistical report.
The follow-up report will include written comments to show what elements have received copies.
SLIDE 10 OFF:
SLIDE 11 TO 12 ON:
INSTRUCTOR NOTE: Refer students to AR 190-11, Para 2-11.
Commanders/directors will be selective in assigning personnel to duties involving control of all categories of
AA&E. Only personnel who are mature and stable and have shown a willingness and capability to perform assigned tasks in a dependable manner will be assigned to duties that involve responsibility for the control, accountability, and shipment of all categories of AA&E.
As part of this selection process, personnel assigned duties involved in the control, accountability, and shipment of AA&E will be screened and evaluated using DA Form 7281 (Command Oriented Arms, Ammunition, and Explosives (AA&E) Security Screening and Evaluation Records). Completed forms will be retained on file within the command, until the individual departs or is relieved of his or her AA&E-oriented duties. In addition, the senior commander or garrison commander will develop procedures to ensure the following:
Commanders/directors/managers who are responsible for the supervision of the personnel and the AA&E will pro-hibit access to personnel specified in paragraphs a. and b., above, when doubt exists as to their reliability or trustworthiness. All personnel will be required to undergo a command-oriented security screening or an equivalent foreign country check before access is authorized. The security screening check will be designed to provide the commander reasonable assurance that personnel with character traits that raise significant doubt as to their honesty or stability are not afforded access. At a minimum, the command-oriented security screening will include—
(1) A personal interview of the individual conducted by his or her immediate commander or supervisor.
(2) A request for medical file check of active duty military personnel.
(3) A personnel records check.
(4) A records check of the PM, DES, or security office.
(5) A records check of local civilian law enforcement agencies in the area of the person's residence, if permitted by state or local laws.
SLIDE 11 TO 12 OFF:
SLIDE 13 ON:
INSTRUCTOR NOTE: Refer students to AR 190-11, Para 3-6, Para 4-2e, Para 4-16, and Appendix F.
The IDS is an essential part of the PS system. The IDS consists of the combination of electronic components, including sensors, control units, transmission lines, and monitoring units integrated to be capable of detecting all types of intrusion into an area protected by the system including the stay-behind threat. An IDS includes both interior and exterior systems. The system will be a DOD standardized system or
DA-approved commercial system. The following policy applies:
a. Central monitoring station.
(1) A central monitoring station (CMS) will be provided at which alarms will present audible and visual alerts and from which a response force will be dispatched. The response force is not required to be collocated with the CMS.
(2) The CMS will alarm with audible and visual alerts whenever the system detects possible intrusion into the protected area or when the system is turned off, malfunctions, or is placed in maintenance mode.
(3) Some means of communication will be provided between the protected area and the CMS to coordinate status changes. Telephone communication should be considered.
(4) When IDSs are used in civilian communities, arrangements will be made to connect alarms to civil police head-quarters, private security companies, or a monitoring service from which immediate response can be directed. A commer-cial answering service is not authorized. Coordination is required with civil authorities to ensure a response force can be directed immediately.
b. Response force. The response force should respond to an activated alarm as soon as possible, but in no case may arrival at the scene exceed 15 minutes.
c. Alarm circuitry.
(1) Circuitry will be used that requires alarm signals to be cleared either at the CMS or from inside the protected area.
(2) Circuitry will be configured to ensure that alarms that announce intrusion detection have priority over other events announcements, such as a power or communication change.
(3) Use of alarm delay switches at RC facilities is prohibited.
(4) On and off, access, maintenance mode, and secure switches not located at the CMS will be located within the protected area.
d. Sensors.
(1) All AA&E storage facilities (other than bulk storage facilities) that require an IDS will be protected by at least a heavy-duty, industrial-grade balanced magnetic switch (BMS) and a volumetric sensor, such as a passive infrared sensor.
(2) The sensors will comply with the standards in Unified Facilities Guide Specification (UFGS) 28 10 05, available at the Whole Building Design Guide website at http://www.wbdg.org/.
(3) Walk-test lights should be disabled.
(4) Boundary sensors, such as vibration sensors, are encouraged.
(5) Dual- and tri-technology sensors, without need for independent alarm condition sensing, are authorized.
(6) Additional levels of protection, when practical, are encouraged (duress signaling components, for example) and will be considered for Category I and Category II arms storage facilities.
e. Personal identification number.
(1) A separate personal identification number (PIN) will be issued to each person whose duties require the ability to operate the IDS.
http://www.wbdg.org/
(2) The PIN will not be shared.
(3) The PIN will not be written anywhere except for official record maintained by the facility manager or designee.
(4) The PIN that has been or believed to be compromised will be immediately replaced.
(5) The PIN will be withdrawn immediately when the individual to whom it was issued departs the organization or no longer requires the ability to operate the IDS.
(6) The PINs will be secured to the same degree as afforded to IDS keys and to keys and combinations used to access the protected area.
(7) The PIN and IDS point of contact call rosters will be reviewed semiannually by the facility manager or designee to ensure the information is current and will document this, in writing, with an informal memorandum retained on file for 1 year.
(2) Circuitry will be configured to ensure that alarms that announce intrusion detection have priority over other events announcements, such as a power or communication change.
(3) Use of alarm delay switches at RC facilities is prohibited.
(4) On and off, access, maintenance mode, and secure switches not located at the CMS will be located within the protected area.
d. Sensors.
(1) All AA&E storage facilities (other than bulk storage facilities) that require an IDS will be protected by at least a heavy-duty, industrial-grade balanced magnetic switch (BMS) and a volumetric sensor, such as a passive infrared sensor.
(2) The sensors will comply with the standards in Unified Facilities Guide Specification (UFGS) 28 10 05, available at the Whole Building Design Guide website at http://www.wbdg.org/.
(3) Walk-test lights should be disabled.
(4) Boundary sensors, such as vibration sensors, are encouraged.
(5) Dual- and tri-technology sensors, without need for independent alarm condition sensing, are authorized.
(6) Additional levels of protection, when practical, are encouraged (duress signaling components, for example) and will be considered for Category I and Category II arms storage facilities.
e. Personal identification number.
(1) A separate personal identification number (PIN) will be issued to each person whose duties require the ability to operate the IDS.
(2) The PIN will not be shared.
(3) The PIN will not be written anywhere except for official record maintained by the facility manager or designee.
(4) The PIN that has been or believed to be compromised will be immediately replaced.
(5) The PIN will be withdrawn immediately when the individual to whom it was issued departs the organization or no longer requires the ability to operate the IDS.
(6) The PINs will be secured to the same degree as afforded to IDS keys and to keys and combinations used to access the protected area.
(7) The PIN and IDS point of contact call rosters will be reviewed semiannually by the facility manager or designee to ensure the information is current and will document this, in writing, with an informal memorandum retained on file for 1 year.
m. Testing and maintenance.
(1) Monthly operational checks will be conducted to ensure sensor activation and to visually inspect components and conduit for evidence of tampering.
http://www.wbdg.org/
(2) Commercial IDSs employing sensors equipped with a remote-test feature that activate the same sensing phenomenology as would an actual intruder do not require operational checks by organization personnel.
(3) Each sensor component, to include tamper circuits and equipment, will be checked and tested by alarm maintenance personnel a minimum of every 6 months during routine preventive maintenance.
(4) Maintenance will be provided by personnel who are qualified to install and repair IDSs. Maintenance will be per-formed consistent with operational requirements to ensure continuous operation and reliability of each system.
SLIDE 14 OFF:
SLIDE 15 ON:
G. Arms Racks and Storage Container
INSTRUCTOR NOTE: Refer students to AR 190-11, Para 4-2b.
(1) When not in use, arms will be stored in banded crates, metal containers, approved standard issue racks or locally fabricated arms racks, and secured in approved weapons storage facilities. Standard issue approved metal wall lockers or metal cabinets may be used. Crates or containers will be banded, locked, or sealed in a way that will prevent weapon removal without leaving visible signs of tampering. Screws or bolts used in assembling containers, lockers, or cabinets will be made secure to prevent disassembly.
(2) Standard issue DA-approved arms racks will be obtained through government supply channels.
Consider all arms racks that have a NSN and are not a part of a shipping container as DA-approved.
Weapons without a specific standard issue arms rack may be secured in a DA-approved Universal Arms
Rack (NSN 1095–01–454–6320, rack, storage, small arms, incorporated). The continued use of existing locally fabricated arms racks is prohibited unless certified as security equivalent to standard issue racks by
DA. Modifications to existing DA-approved arms racks, which have assigned NSNs, are prohibited without prior approval from DA. A Tank-automotive and Armaments Command Life Cycle Management Command logistics assistance representative and a battalion command-level representative will jointly perform certification authorizing the continued use of prior locally fabricated arms racks. The joint certification will serve as verification of the security adequacy of such arms racks. The AMC Executive Manager for Small
Arms Logistics and Demilitarization (EM–SALD) Office at Rock Island, IL will provide the certification training and administer the certification process and issue certificates required. Locally fabricated arms racks that are logistics assistance representative and battalion representative certified will be considered DA-approved
EM–SALD; stamped with a serial number, identifying the type of weapon rack; and tracked in a local database maintained by the EM–SALD office. The using unit will maintain the certification on file where such racks are used, as it will serve as security verification of the adequacy of such racks. The minimum requirements for certification of previously locally fabricated arms racks are—
(a) Fabrication and/or modification constructed of metal having an inherent strength that would prevent an individual from manipulating components (without tools) such that the weapon, receiver, or barrel could be removed.
(b) Overall design of fabrication and/or modification such that a weapon, receiver, or barrel cannot be removed by disassembly of the weapon/component and/or the rack without damage to the rack.
(c) Hinged locking bars for racks have the hinge pin welded or otherwise secured to prevent disassembly.
(d) Bolts or machine screws used for fabrication or modification are a minimum of 3/8–inch diameter. The bolt and nut will be tack welded, brazed, or peened to prevent disassembly.
(e) When all features in paragraphs 4–2b(2)(a) through 4–2b(2)(d) , above, are adequate, apply certification serial number provided by the EM–SALD to the rack in an appropriate location. Metal stamps, indelible marker, or paint stencil may be used.
(3) Requests for certification of locally fabricated or modified arms racks will be submitted to the
Commander, U.S. Army Tank-automotive Command Life Cycle Management Command (AMSTA – LC –
CSL), Rock Island, IL 61299 – 6000.
(4) All arms racks or containers will be locked with approved secondary padlocks. In facilities that are not manned 24 hours a day, rifle racks and containers weighing less than 500 pounds will be fastened to the structure (or fastened together in groups totaling more than 500 pounds) with bolts or with chains equipped with secondary padlocks. Bolts used to secure racks will be spot welded, brazed, or peened to prevent easy removal. Chains used to secure racks (and containers) will be heavy-duty hardened steel, welded, straight links steel, galvanized of at least 5/16–inch thickness, or of equivalent resistance to force required to cut or break a secondary padlock.
(5) When weapons are in transit, stored in depots or warehouses, or held for contingencies, the weapons crates or containers need not be fastened to the structure. However, such crates or containers will be banded or locked and sealed in a way that will prevent weapon removal without leaving visible signs of tampering. The facilities and buildings in which these weapons are stored will meet the structure and other security requirements of this regulation. Arms being unpacked or packed for shipping or in assembly-line configuration in a maintenance repair or rebuild facility do not require storage in racks or containers.
However, the facilities in which they are stored will meet the structure and other security requirements of this regulation.
SLIDE 15 OFF:
SLIDE 16 ON:
i. Security lighting.
INSTRUCTOR NOTE: Refer students to AR190-11, Para 4-2c.
1) Interior and exterior lighting will be provided for all arms storage buildings, buildings in which arms storage are located, and arms storage rooms. The lighting will be sufficient to allow guards (or individuals responsible for maintaining surveillance) to see illegal acts, such as forced entry or unauthorized removal of arms during hours of reduced visibility.
2) Areas appropriate for lighting include entrances to buildings, corridors, and arms rooms. When an arms room is located inside a building, the entrance door to the arms room will be illuminated. Arms rooms that are located within another room (for example, a supply room), do not require security lighting over the arms room door, instead the exterior door to that room (for example, supply room) will be illuminated.
3) Security lighting will also be provided for motor pools, hangers, and outside parking areas where vehicles or aircraft that have weapons installed or on board.
4) Switches for exterior lights will be installed so that they are not accessible to unauthorized individuals.
5) Exterior lights will be covered with wire mesh screen or equipped with vandal resistant lenses that will prevent the lights from being broken by thrown objects.
SLIDE 16 OFF:
SLIDE 17 ON:
j. Doors, locks and locking devices.
INSTRUCTOR NOTE: Refer students to AR 190-11, Para 4-2d.
INSTRUCTOR NOTE: Pass around a high security lock and secondary padlock while explaining their operations to the students.
1) Except for GSA approved Class 5 steel vault doors with built-in 3-position, changeable combination locks, and doors used for access to arms storage rooms or structures will be locked with an approved high security locking device or high security padlock and hasp providing comparable protection to the locks.
2) An approved high security shrouded hasp will be used to secure Category I and II AA&E storage facilities to enhance their security.
3) On existing storage facilities equipped with double-door protection, high security padlocks and hasps will be used on the most secure door. Secondary padlocks will be used to secure the other door of the double-door concept.
4) Other doors that cannot be secured from the inside with locking bars or dead bolts will be secured on the inside with secondary padlocks (for example, issue window or portal). When high security hasps are installed, locking bars and T-pins should be left in place to aid in opening and closing doors and prevent any misalignment of the hasps.
5) Key and lock controls will be established per AR 190-11, Para 3-8 and will be discussed later in this lesson.
k. Additional Controls:
SLIDE 17 OFF:
SLIDE 18 ON:
INSTRUCTOR NOTE: Refer students to AR 190-11, Para 4-2e, and Table 4-1.
1) Rendering weapons inoperable.
a) If the facility is not located on a military installation, weapons will be rendered method shown in Table 4-1 under any of the conditions below:
(1) A facility does not meet structural criteria.
(2) A threat is received.
(3) An IDS is inoperative for a period of 24 hours or longer.
(4) During periods of annual field training, if arms are left in the facility.
(5) Decision of the commander having direct security responsibility for the facility.
b) Storing removed items.
(1) The items removed for the purpose of rendering a weapon inoperable will be tagged with the weapons serial number to ensure return to the same weapon and secured in a separate building.
(2) Etching of weapon serial number on the removed parts is prohibited.
(3) The removed items will be stored in a locked container in a secure area away from the arms storage facility.
(4) If a secure area is not available for storage of these items, the container will be stored in the arms storage facility and secured to the structure with an approved lock and chain or equal methods when the container weighs less than 500 pounds.
l. Reserve Component (RC) weapons.
1) The Army policy of close cooperation between Active Army and RC activities is an essential element in eliminating the theft or loss of AA&E.
2) At times, RC activities may need to use local Active Army facilities for the temporary storage of AA&E as the result of emergency situations: (for example, during vehicle breakdown when transporting weapons), when an increased threat situation is forecast or present and during rifle matches.
3) Active Army facilities are authorized and encouraged to assist in temporarily securing RC items.
4) The receiving unit will ensure the accountability (number and type items, including serial numbers) of those items accepted for storage.
5) The above policy also applies between Reserve components as well as the temporary storage of Active stocks at Reserve storage facilities.
SLIDE 18 OFF:
SLIDE 19 ON:
m. Consolidated Arms Rooms (Ref: AR 190-11, Para 4-4)
a. Arms belonging to more than one unit or organization may be stored in the same arms room or arms storage facility.
b. One commander will be designated as having responsibility for the overall security of the consolidated storage facility.
c. Procedures will be established to fix responsibility for issue, receipt, and physical accountability for arms, including ammunition, and all other sensitive items, stored in the consolidated storage facility per AR 710–2 and DA Pam 710–2–1.
d. Access controls will be established to ensure protection of each unit's arms.
e. Arms and other sensitive items will be segregated by unit.
(1) Expanded metal mesh screening will be utilized (see USACE STD design drawing 40–21–01 at http://www.usace.army.mil).
(2) Units with small quantities of arms may use locked metal containers instead of separation by security cage.
(3) Cages will be locked. Each cage will be identified with unit designation (name).
f. Procedures for such consolidated arrangements will be established in the SOP of the consolidated storage facility, or in the SOP of the higher headquarters. In addition to those procedures as mentioned in paragraph
4–4b, above, the SOP will establish who will obtain the operational load of ammunition, type/quantity, and the accountability of the same for the armed guard. It will also establish procedures for who is responsible for the armed guard in case of IDS failure for short and extended periods of time. The SOP will also include a plan for testing of the IDS. (RCs should also include in the plan who will take over such duties in the event of mobilization and who will be responsible for weapons left behind by the mobilized unit.)
SLIDE 19 OFF:
SLIDE 20 ON:
n. Privately-Owned Weapons (POWs) and Ammunition:
INSTRUCTOR NOTE: Refer the students to AR 190-11, Para 4-5.
A. The SC will establish procedures and publicize punitive policies that regulate privately owned weapons, explosives, and ammunition on the installation. Such policies will provide procedures for—
(1) Registration of firearms belonging to personnel living on the installation and registration of firearms by personnel who bring a firearm onto the installation for the purpose of engaging in authorized activities such as hunting, dog training activities, or marksmanship events.
(2) Identification of prohibited weapons such as crossbows, nun-chucks, swords, and throwing stars.
(3) The requirement for all Soldiers and Family members to comply with federal, state, and local laws and regulations on ownership, possession, registration, off-post transport, and use of firearms.
B. Storage of privately owned firearms including authorized war trophies.
(1) The SC—
(a) Will ensure that firearms and ammunition belonging to Soldiers living in unit billets or on-post quarters are secured in the installation armory or unit arms room in approved locked containers separate from military http://www.usace.army.mil/
AA&E.
(b) May authorize storage of firearms and ammunition at a Soldier’s on-post quarters provided they are properly se-cured. Firearms will be secured in either a locked container or provided with a trigger lock.
Ammunition for the firearm will be secured separately from the firearm in a locked container.
(2) Unit commanders will—
(a) Account for and inventory privately owned firearms and ammunition secured in unit arms.
(b) Ensure that a DA Form 3749 has been issued for each privately owned firearm secured in the arms room. Privately owned firearms will be inventoried in conjunction with and at the frequency of the inventory of military weapons.
(c) Establish limits on the quantity and type of privately owned ammunition stored in the arms room, based upon avail-ability of space and safety considerations.
(d) Ensure that inspections are conducted per AR 190–13 and this regulation to ensure proper storage and control.
(e) Process unauthorized AA&E per AR 195–5.
(f) Post applicable local regulations and state and local law information on ownership, registration, and possession of firearms and ammunition on unit bulletin boards.
(g) Brief all newly assigned persons on this regulation and subordinate command guidance. All personnel will be made aware of changes.
(3) Personnel keeping or storing privately owned firearms and ammunition (including authorized war trophy firearms) on an installation will—
(a) Comply with federal, state, and local laws and regulations on ownership, possession, registration, off-post transport, and use.
(b) Store both firearms and ammunition in the unit arms room or other locations authorized by the installation commander.
(c) Follow local security and safety regulations. Safeguard the unit-issued DA Form 3749 for turn-in to the unit armorer, when the firearm is withdrawn from the arms room.
(d) Withdraw privately owned firearms and ammunition from the unit arms rooms only upon approval of the unit commander or authorized representative.
(e) Comply with the National Firearms Act and other relevant laws and regulations when receiving or bringing arms into the United States.
SLIDE 20 OFF:
SLIDE 21 ON:
o. Restricted Area Posting:
INSTRUCTOR NOTE: Refer the students to AR 190-11, Para 4-15 and AR 190-13, Para 6-4.
1) Except when such action would tend to advertise an otherwise concealed area or when in conflict with host nation agreements. Signs or notices will be posted in conspicuous and appropriate places to identify the
AA&E facility as a restricted area. This includes signs posted at each entrance or approach to the area and on perimeter fences or boundaries of the area.
2) Post signs so as not to provide concealment of an intruder or obstruct visual assessment.
3) Post conspicuous signs and notices to give people approaching a restricted area actual knowledge of the restriction.
4) Each sign or notice will be marked with the words "RESTRICTED AREA" and include the following warning notice: THIS ACTIVITY HAS BEEN DECLARED A RESTRICTED AREA BY AUTHORITY OF THE
INSTALLATION COMMANDER IN ACCORDANCE WITH THE PROVISIONS OF THE DIRECTIVE
ISSUED BY THE SECRETARY OF DEFENSE ON 10 DECEMBER 2005, PURSUANT TO THE
PROVISIONS OF SECTION 21, INTERNAL SECURITY ACT OF 1950. UNAUTHORIZED ENTRY IS
PROHIBITED. ALL PERSONS AND VEHICLES ENTERING HEREIN ARE LIABLE TO SEARCH.
PHOTOGRAPHY OF THE FACILITIES IS PROHIBITED WITHOUT SPECIFIC AUTHORIZATION FROM
THE COMMANDER, DEADLY FORCE IS AUTHORIZED.
SLIDE 21 OFF:
SLIDE 22 ON:
q. Security of Tools:
INSTRUCTOR NOTE: Refer the students to AR 190-11, Para 4-18
a. Tools such as hammers, bolt cutters, chisels, crowbars, hacksaws, cutting torches, and similar items which could be used to assist in gaining unauthorized access to an arms storage facility must not be readily accessible to intruders. Tools of this type should be removed from the vicinity of the arms storage facility or room. When an arms storage facility is the only security location available, such tools will be stored in a locked container within the facility. When the access door to an arms storage room is located within the unit supply room, tools will not be stored in the supply room.
b. When other secure storage facilities are reasonably available, high-value items will not be stored in arms storage facilities. Such items include field glasses, compasses, watches, and highly valuable items subject to pilferage. In the absence of secure facilities, commanders may authorize, in writing, those sensitive items to be stored in arms storage facilities. In the absence of secure facilities, commanders will authorize, in writing, those sensitive items to be stored in arms storage facilities. These items should be placed in a lockable container, and keys to cages and/or weapons racks/containers should not be on the same ring as these keys. Keys to weapons racks/containers should not be issued if only the high dollar value items are to be accessed. The same rule should apply if only weapons are to be issued; the keys to the high dollar value containers should not be issued.
SLIDE 22 OFF:
Check on Learning:
SLIDE 23 ON:
Question: The commander must appoint in writing, a commissioned officer, warrant officer, or noncommissioned officer to act as what for the unit? (AR
190-11)
Answer: Physical Security/Arms Room Officer.
Question: If an arms rack weighs less than 500 pounds, what must be done to meet physical security requirements? ( AR 190-11)
Answer: Must either be secured to the building or secured together with other racks to total over 500 pounds.
SLIDE 23 OFF:
Review Summary: SLIDE 24 ON:
Conduct a Review/Summary of the information presented in this Learning Step.
Control physical security procedures for the Arms Room
SLIDE 24 OFF:
TLO - LSA 2. Learning Step / Activity TLO - LSA 2. Maintain proper Key Control.
Method of Instruction: Demonstration
Instr Type (I:S Ratio): Military - ICH (1:15)*
Time of Instruction: 3 hrs Media Type: PowerPoint Presentation
Other Media: Unassigned Security Classification: This course/lesson will present information that has a Security
SLIDE 25 ON:
a. The unaccompanied access roster (memorandum) will be prepared to inform an individual that he or she is being designated to do a specific job on behalf of the commander.
SLIDE 25 OFF:
SLIDE 26 TO 27 ON:
INSTRUCTOR NOTE: Refer students to AR 190-11, Para 3-8. Review the contents of the paragraph. Have the students open the Microsoft Word program or get a blank sheet of paper and a pencil.
b. Remind students that the commander will select assigned personnel to perform duties involving control of arms room and each individual selected must be personally screened and evaluated. These individuals, after passing the initial screening and any specific requirements, will be listed on the Unaccompanied Access
Roster.
SLIDE 26 TO 28 OFF:
SLIDE 29 TO 30 ON:
INSTRUCTOR NOTE: Have students refer to AR 190-11, Para 2-11. Review the contents of the paragraph.
SLIDE 29 TO 30 OFF:
SLIDE 31 TO 32 ON:
c. Prepare the Unaccompanied Access Roster (memorandum).
INSTRUCTOR NOTE: Explain when personnel depart the unit or become disqualified, a new roster must be prepared.
1) Top center and five spaces down. Enter in [DEPARTMENT OF THE ARMY] for header.
2) Under DEPARTMENT OF THE ARMY, enter in [Headquarters and Headquarters Company].
3) Under Headquarters and Headquarters Company, enter in [13th Military Police Battalion].
4) Under 13th Military Police Battalion, enter [Fort Gregg-Adams, Virginia 23801].
5) Two spaces down, starting at the left margin. Enter [ASTM-MP-HHC] for the office symbol.
6) At the right margin, on the same line as the office symbol, enter the date. Enter [1 October 20XX] for the date.
7) Three spaces down, under office symbol. Enter [MEMORANDUM FOR RECORD].
8) Two spaces down, under MEMORANDUM FOR PERSONNEL CONCERNED, enter
[SUBJECT: Unaccompanied Access Roster].
9) Three spaces down, under SUBJECT: Unaccompanied Access Roster, enter in
1. Under the provisions of AR 190-11, the following named personnel are authorized unaccompanied access to the Arms Room Storage Facility located in Building 4210 during…
This is the start of the file's text. The full file is on GovTribe.
File details come from the government source that posted it. Updated .