Attachment_0004_-_Target_Drawings.pdf

D

C

B

A

D

C

B

A

8 7 6 5 4 3 12

DESIGN ACTIVITY

SIZE CAGE CODE

SCALE UNIT WT.

DRAWN BY DATE(YEAR-MO-DA)

CHECKER ENGINEER

ENGINEER QUALITY ENGINEER

DRAWING APPROVAL

DESIGN APPROVALMATL ENGR MODELED BY

CONTRACT NUMBER

CONTRACTOR

SHEET

DRAWING SIZE D

TOLERANCES ON ANGLES �#� �$�

2 PLACE DECIMALS �#�

3 PLACE DECIMALS �#�

FORMAT: D_TACOM_ENG_1_0 12345678

DWG NO.

SEE NOTE 6

7.00 1.00

46.00 +1.00 -.00

10.50 +.50 -.00

8.50 +.50 -.00

12.968 .025

R

2 PLACES

3.00 .25

R

2 PLACES

2.00 .25

R

2 PLACES

3.50 .25

20.00 +.50 -.00

R3.00 .03 2 PLACES

69.0�$�.5�$�

1.030 .015

2 PLACES

2.60 .06

2 PLACES

.765 .015

2 PLACES

1.060 .015

2 PLACES

1.930 .015

2 PLACES

.465 .015

.750 .015

40.0 +.5 -.0

SEE NOTE 3

2.25

2.25

1.00

REVISIONS

APPROVEDDATE(YEAR-MO-DA)DESCRIPTIONDRAWING REV

INITIAL RELEASE

1 OF 1 3/16

1306623219200D

3-D TARGET, TALL

US ARMY

ARMAMENT RESEARCH, DEVELOPMENT AND ENGINEERING CENTER

PICATINNY ARSENAL, NEW JERSEY 07806-5000

YEAR-MM-DDM. CROSSON

YEAR-MM-DDL. MORSE

J. JENNINGSA. STETSON

T. MICHOSKIA. STETSON

2016-07-05J. KREIDER

APPLICATION

USED ONNEXT ASSY

IRETS

PMIC

MECHANICAL

PROPERTIES

YP

TS

EL2

RA

BH

RH J. KREIDER

THIRD ANGLE PROJECTION

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN INCHES

DO NOT SCALE DRAWING

PART NO. 13066232

THIS DRAWING WAS GENERATED FROM A SOLID MODEL

AND IS CAD MAINTAINED. CHANGES SHALL BE

INCORPORATED BY THE DESIGN ACTIVITY.

NSN

NOTES:

1. APPLICABLE STANDARDS/SPECIFICATIONS:

A. MIL-F-13926B

B. ASME Y14.5-2009

C. ASME Y14.100-2013

2. MATERIAL: SPECIFICATION CONTROL DRAWING 9363146.

3. MATERIAL THICKNESS:

A. ALONG BASE 2.25 INCHES ABOVE BASE OF THE

TARGET SHALL BE .065-.300 INCHES.

B. REMAINDER OF ENTIRE TARGET SHALL NOT BE LESS

THAN .065 INCHES.

4. TARGET SHALL WITHSTAND 6,000 UP AND DOWN

CYCLES (UP AND DOWN = 1 CYCLE), IN ALL

SPECIFIED WEATHER CONDITIONS, AND WITHOUT

DEGRADATION. THE TARGET IS RAISED FROM 0�$� TO

90�$� IN LESS THAN 0.5 SECONDS, AND LOWERED FROM

90�$� TO 0�$� IN LESS THAN 0.5 SECONDS.

5. ALL AREAS NOT DEFINED BY A DIMENSION ON THE

DRAWING ARE AT THE CONTRACTOR'S DISCRETION.

6. DIMENSION ONLY APPLIES UP TO 2.25 INCHES ABOVE

BASE OF THE TARGET.

7. ITEM IDENTIFICATION: AFTER FINAL FINISH APPLY THE

FOLLOWING MARKING ON THE BACK OF THE SILHOUETTE

IAW MIL-STD-130 BY METHOD OF STENCIL OR RUBBER

STAMP, IN CONTRASTING COLOR IAW A-A-208, OR MOLDED

IN CHARACTERS (FONT=ARIAL, MINIMUM 1/2" HIGH):

19200 - 13066232

MANUFACTURER'S CAGE CODE

DATE OF AND/OR LOT NUMBER OF MANUFACTURE

MARKINGS SHALL NOT INTERFERE WITH THE TARGET'S RIGIDITY.

8. COMPLETENESS OF MACHINING AND

FINISHING OPERATIONS PER DRAWING 13066232.

9. TARGETS SHALL BE PACKAGED BY NESTING EACH INSIDE THE

NEXT ONE. EACH BOX SHALL INCLUDE A QUANTITY OF 35 TARGETS.

10. QUALITY ASSURANCE PROVISION REQUIREMENTS

PER DRAWING 12993884 APPLY.

DISTRIBUTION STATEMENT A.

APPROVED FOR PUBLIC RELEASE;

DISTRIBUTION IS UNLIMITED.

SEE DETAIL A

SECTION B-B

SCALE 3/8

DETAIL A

SCALE 5/8

III

V

COLOR

III

Y

MATERIAL FLOW RATE

III

Y

MATERIAL TENSILE STRENGTH

III

W

ULTRA VIOLET (UV) ADDITIVES

III

V

WORKMANSHIP

C

III

Y

MATERIAL DENSITY

III

C

III

C

III

C

III

C

III

C

Distribution Statement A